Contents | 1. Fast Assembly 1.1. Moon-1 1 12 Moo 4 1l. Operation Pan: 7 21 Home Page -..oocccvoerrccimscne . 2.2. File Directory Interface 23. Molten Central Interface 2.4 Functional Module Control Interface 111 3D Printing 3.1. Set the Zero Point 9 10 3.3. Install the Filament 1 3.4. Use the Slice Software 12 3.4.1. Install the Slice Software 12 3.4.2. Configuration for Inhalant Use 13 Symbol Description | 3.4.3. Online Printing 13 3.4.4. Offline Printing 18 IV. Laser Engraving 4.1.
e i 1.1. 4 install the Main Control Board Install the Z-axis on the base with screws (M3x8 hex screw x8). Install the main control board back with screws (M3x8 hex screw x3). As shown below As shown below 1.1. 8 Inst ail the X axis Linear Actuator 1.1.8 Install the Functional Moguls Install the X-axis on the Z-axis siding plate with screws (M3x8 hex screw Select the functional module you need and fix it on the X-axis with screws 4). As shown below (M8 hox screw x4).
e e A warning: Wrong connection of scabies way cause burnout of man control bored! Hot-pkg & surety protected Always Eke sure that a1 cables are pigged In spice harbors power ond Plugging of scabies during positron status wil cause malformation Before power on the machine, please follow the chart below and connect all modules to the main control board comely. Functional module cable) Heated bed cable) < LCD touch pad 1.1.
L T e Install the Z-axis an the base with screws (M3xB hax craw x16). As shown below 1.2 4 Adjust the the Position of Z axis Siding Plato Push two sliding plates of Z-axis downwards o the end. As shown barrow Sliding plate e T Install X-axis on the siding plates of Z-axis with screws. As shown blow X-ads cable should be on this side e e T Install the main control board back with screws (M3x5 hex screw x3). As shown below Note: 1. Pay attention to the position of X-axis cable before installation.
T Attach 4 gummed gaskets on the back of heated bed and align them to the Mace the Y-sis sliding plats to an appropriate position and fix the heated bed mounting holes. As Shawn below ‘on It with forswear (M3x8 hex sower x4). Fix the filament support on the Z-axis with screws (M3xB screw x2). As shown below. @ee® Gum gaskets x4 1.2.10 Correct the Cables Before power on the machine, please follow the chart below and connect all modules to the man control board correctly.
1l | Operation Panel | {SWEETIE— Display file name current’y being executed Display execution progress of current file Display current nozzle temperature Display current temperatures of heats bed only available for 3D printing function ‘Work process control buttons: start, pause and stop (In order) Raul-time working sped control butane, Left " and right Interface switching buttons (In order): Home gaps, Mlle directory Interface, Functional module control interface, Motion control Interface Display current c
3D / Laser } CNC mauled control Interface switching button Display current temperature of nozzle / heated bed Set target temperature Nozzle heating: For testing whether the snazzily heating ls normal, press gala to stop heating Heated bed heating: For testing whether the bed heating l& normal, peers again to stop heating Filament feed button:For Installing lament &nd testing extrusion performance, provided that the nozzle Is preheated to about 200°C, Flaubert retraction button: For removing consumable, prov
< O Description: Not Avery Moon needs fo be leveled after proper assembling, pleads skip this section if the leveling condition of your prints hasted bed is fine. Steps to level the heated bed are similar to Section *: except you need to record three different points other than one to define a plans parallel! to the heated bed, these three points must be recorded In order with nozzle In the areas shown In the drawing bilious, one In each.
.2 Configuration for Inhalant Use O Description: Please visit www.dobot.cc to download the related tutorial videos and software. . . ®RunCua310andgo " o name your | i Operation steps: | i, and click “7ci 3 dllo\eg of Machine Sat tings wil popup J & Lw Configures the machine Peb” o Volume Note: Origin of Moon-1 and Moon-2 Is defaulted at left-bottom comer of the heated bed, so do not sack the “origin at center” box, otherwise the medal will be printed outside of the jested bed.
Profile the model: @ Adjust the mode: left click on the medal, four options and you can adjust as needed. and 'u' will appear on the left side of the interface, 5 @ View the details of the since: click the drop-down list on the » upper misdid comer of th Interface and sslsct » @ list on the right bottom comer of the to view the details of the since. i ‘ Note: Pleas makes sure the machine has bean properly inked t your PC, power it on before starting Cara.
3.4.4 Offline Printing Note: The U disk or 5> card format shall be Fat with the capacity not greater than 32GB. Operation steps : 1. Save Geode file to U disk or SD card with curs. 2. Insert U disk or SD card to the printer. 3. Follow the steps bellow to execute the Geode fell. Moon Wit for the heated bed and noodle to be heated to the target temperature Start printing automatically Click the " button to.
n e Warning: Never touch, A Away from children] [ protective o I No Touch Note: Please be sure to wear the goggles and use the protective shied for safety! 4R Operation steps: Stick a small piece of tape to the bottom of work piece (graceless double-sided tape Is recommended), keeping the edges of the work piece aligned with grids and adhere it to the heated bed.
Wear the protective glasses to control the Z-as to focus the laser Adjust the X-ax and Y-axis to move beam {until the spot is the minimum which should be judged by the laser spot to desired position, naked eyes) Switch the step distance to for fine tuning. generally intersection at the lower left comer of the work piece.
[T Note: Currently the software only supports offline working. Please visit wiwwidokiot.cc to download the related tutorial videos and software. Operation steps: @ Select to import ] i @Ticktock generate principled Click the Laser tab page clink ]s@» (o Click Store the file into U ® Select the fail to engrave @s'm o save Meade via the touch pad | u can adjust the sis of the engraving patter.
Select Click to. rats J ke > l gfil Operation steps: |®cm . l S w2 [ @ Store the e into U dicks or SD card o (w Select the file to carve via the touch pad () sermonize you can adjust the size of the engraving patter -+ adjust according to the hardness of different materials, the materials that are more difficult to carve require the sower speed. Carve speed can be adjusted real-me through the touch screen.
