Instructions / Assembly

ManualsBrandsDock Edge ManualsAutomotive8 l Grey Toilet Passport Space Saver

OPERATING INSTRUCTIONS:

CAUTIONS: Changes in altitude while travelling, or other conditions, may cause pressure build-up in the waste holding tank. Before use, always check for pressure build-up by first opening and

closing the flush valve with the lid and seat in the closed position. NEVER ADD WASTE HOLDING TANK CHEMICALS TO THE FRESH WATER SUPPLY. When adding chemical to the waste

holding tank, first open the flush valve fully. Never add chemical into the bowl and then flush into the holding tank.

1. How To Separate The Water Tank & Holding Tank Sections: On models with a single spring lock clip, pull out slightly on the single spring lock clip located at the rear of the fresh water tank.

Lift up on the rear of the water tank to disengage the front clasp, then lift vertically. To reassemble the two sections, align and engage the front clasp then press down gently on the rear of the

water tank until the spring lock clip engages.

On models with two spring lock clips, pull out slightly on the spring lock clips located on either side of the water tank then lift vertically. To reassemble the two sections, align the recesses in the

water tank with the locating pins on the holding tank and press down gently on the top of the toilet until the spring lock clips engage.

2. Filling and Adding Fresh Water Additives to the Fresh Water Supply Tank: Remove the water fill cap located at the top rear right-hand corner by grasping the edge of the cap and pulling

up. If using a fresh water additive, read the directions on the package for the proper amount to use. Fill the fresh water tank with water to the bottom of the fill tube. DO NOT OVERFILL. Replace

the water fill cap by pressing onto the water fill spout.

Operating the Water Pump: To add water to the bowl prior to use, operate the pump in an up-and-down stroking motion. Periodically lubricate the pump tube shaft with vaseline or silicone

grease.

3. Flushing: To flush after use, open the flush valve by pulling the handle located at the front of the toilet straight out. Push the handle back in all the way to close the valve. When the valve is

closed, the holding tank is sealed. It is not necessary to have water in the bowl after it has been flushed, but water should be added before use to ensure a proper flush. It is also useful to operate

the pump when flushing in order to rinse the bowl.

4. To Add Chemical Deodorizer to the Waste Holding Tank:

Be sure the flush valve is FULLY OPEN before pouring chemical into the waste holding tank. Read the directions on the package

for the proper amount to use. Open the flush valve fully as shown in Fig. 3. Pour chemical through the bowl opening into the waste holding tank. Pump sufficient water through the bowl to cover

the bottom surface of the holding tank. Close the flush valve fully and agitate the toilet to thoroughly mix the water and chemical.

5. Waste Level Indicator: All models have a waste level indicator located on the front left-hand side of the lower holding tank. As the tank becomes full, a dark indicator line will appear in the

centre of the window. When the line reaches the top, this is an indication that the tank should be emptied.

6 & 7. How to Empty the Waste Holding Tank: Separate the holding tank as previously described. Carry the tank to any permanent toilet waste disposal facility. For splash-free disposal, there

is a pour spout stored in a recess in the bottom of the waste holding tank. Remove the spout by pulling on its front end where the finger recess is located. Remove the plug and threaded cap

from each respective end of the spout. Remove the sealing cap from the holding tank outlet. Position the spout on the tank outlet as shown and attach by tightening the threaded collar ring onto

the tank. Pull up on the air vent valve (red cap) located on the top front left-hand corner of the tank. This will permit air flow through the tank for a smooth discharge of the tank contents while

emptying. Carefully empty the tank by gripping the rear handle and the finger recess in the bottom of the tank at the front. Gradually tilt up the front corner of the tank nearest to you and pour out

the spout on the diagonal. After emptying the tank, rinse with fresh water. Remove the spout and rinse if necessary. Replace the cap on the emptying outlet and push down on the air vent valve

to close. Replace the cap and end plug on the spout and press into the storage cavity. Reassemble and recharge the unit as previously described.

8. To Replace the Rubber Gasket Seal: If the bowl does not hold water or there is leakage from the waste holding tank through the flush valve, first check to see if there is some impediment on

the outer or inner sealing surfaces of the gasket that needs to be removed. If not, the gasket should be replaced. For ease of installation immerse the replacement gasket in warm water for five

minutes prior to installation. When replaced, ensure that the gasket is in the proper position inside the holding tank with the sealing surface vertical as shown.

1- Clapper Gasket 2- Clapper Seal Opening 3- Inside Lip of Holding Tank 4- Correct Position 5- Incorrect Position

9. To Prevent Leakage Out Flush Valve Shaft: First pull out the flush valve handle to expose the plastic ring at the front of the bottom tank. Adjust the tightness of the valve shaft “O” ring seal

until leakage stops by using long-nose pliers and turning the plastic ring CLOCKWISE as shown. If leakage persists, the holding tank should be returned for inspection and repair or possible

replacement. 1- Turn to Tighten 2- Lubricate (vaseline or silicone grease)

CLEANING AND MAINTENANCE: Regularly clean the bowl with Visa Toilet Bowl and Waste Holding Tank Cleaner and Freshener or BIO-SAN® Rinse. Also recommended to clean and fresh-

en the bowl and tank for between-use storage. Other members of the Visa and BIO-SAN® family of Toilet Care Products include; Waste holding tank deodorizers in liquid or powder concentrate

form and rapidly disintegrating, biodegradable Visa Toilet Tissue. Periodically apply petroleum jelly to the surface of the flush valve rubber gasket seal. For cold weather use add a NON-TOXIC

anti-freeze to the fresh water supply tank. To prepare for storage, empty the water tank (including pump chamber) and holding tank. Rinse out the holding tank using Visa Toilet Bowl and Waste

Holding Tank Cleaner and Freshener or BIO-SAN® Rinse, or use one cup of bleach (5% solution) per 5 litres (1 Gallon) of water. Never use abrasive brushes, cleaners or harsh chemicals or

solvents that can scratch the finish or damage plastic surfaces and rubber seals.

1 2

PARTS

1. Lid Cover & Seat

2. Pump Assembly

3. Check Valve

4. Nozzle Assembly

5. Water Fill Cap

6. Fresh Water Tank

7. Spring lock(s)

8. Flush Gasket Seal

9. Tank/ Spout Cap

10. Waste Tank

11. Pour Spout Ass’y

12. Spout End Plug

Have the following

information avail-

able when ordering

replacement parts

(a) Brand Name

(b) Model Number

(d) Part Color

Parts may be obtained from your local dealer, place of purchase or contact:

OUTSIDE NORTH AMERICA

Go to http://cmpgroup.net for the dealer/

distributor nearest you

NORTH AMERICA

Canada Metal (Pacific) Ltd.

7733 Progress Way

Delta, BC, Canada V4G 1A3

Phone: 1-604-940-2010

Fax:1- 604-952-2650

Visa Chemicals

Waste Holding

Tank Deodorizer

Available in:

16 fl. oz. (437ml)

32 fl. oz. (947ml)

67 fl. oz. (2L)

•Eliminates odor

causing molecules

• Non staining

• Non corrosive

• Pleasant fragrance

Visa Chemicals

Waste Holding Tank

Deodorizer Crystals

Available in:

16 oz. (454g)

• Non dusting

granules

•Eliminates odor

causing molecules

• Non staining

• Non corrosive

• Pleasant fragrance

Visa Chemicals

Biodgradable Toilet

Tissue

Available in: 2 Pack

1000 sheets/ roll

• For R.V./ Marine &

portable toilets

•Rapidly disintegrat-

ing biodegradable

paper

• Resists clogging

• Superior strength

• Safe for septic use

Visa Chemicals

Toilet Bowl &

Holding Tank

Cleaner

Available in:

33 fl. oz. (1 Litre)

• Special formulation

for RV/ Marine,

portable or perma-

nent holding tanks

• Cleans & freshens

• Non abrasive

BIO-SAN

Sanitary Fluid

Available in:

67.6 fl. oz. (2 Litre)

• Eliminates odors

• Non staining

• Non corrosize

• Pleasant fragrance

BIO-SAN

Rinse

Available in:

67.6 fl. oz. (2 Litre)

• Keeps water sup-

ply reservoir fresh/

inhibits algae

• Lubricates bowl

surface & flush

valve for easier

flushing

• Leaves stain resist-

ant film

• Fresh scent

® Registered Trademark of:

Canada Metal (Pacific) Ltd.

Summary of content (2 pages)

PAGE 1
OPERATING INSTRUCTIONS: CAUTIONS: Changes in altitude while travelling, or other conditions, may cause pressure build-up in the waste holding tank. Before use, always check for pressure build-up by first opening and closing the flush valve with the lid and seat in the closed position. NEVER ADD WASTE HOLDING TANK CHEMICALS TO THE FRESH WATER SUPPLY. When adding chemical to the waste holding tank, first open the flush valve fully. Never add chemical into the bowl and then flush into the holding tank. 1.
PAGE 2
MODO DE EMPLEO: ADVERTENCIA: Los cambios de altitud u otras condiciones durante un viaje pueden provocar una acumulación de la presión en el depósito de retención. Antes de utilizar el inodoro, verifique siempre el nivel de presión abriendo y después cerrando la válvula de descarga automática, manteniendo la tapa y el asiento en posición cerrada. NO VIERTA NUNCA PRODUCTOS QUÍMICOS PARA EL DEPÓSITO DE DESECHOS EN LA RESERVA DE AGUA LIMPIA.