Installation Guide
Step 3 -
Locate the proper
location for the
receptacle box
cutout using our
cutout template. You
can locate the proper location
from either the inside or backside
of the drawer box, making sure that the arms
will not interfere with the slides and that there is
enough material surrounding the receptacle box to
securely hold it in place.
• Failure to follow these instructions can
cause death or permanent injury. Do
not work on live electrical circuits! Make
absolutely certain power is o before
connecting the device!
• This product is for dry, indoor and permanent
installations only.
• Install the device in accordance with all
national and local electrical codes.
• This manual is for POWERING outlets only.
CAUTION – READ CAREFULLY
NOTICE
How to Install the Outlet
Step 1 - Verify the drawer dimensions. Style
Drawer Blade and Blade Duo require at least 2”
behind the drawer box and Flush needs at least 5”
behind the drawer box.
Step 2 - Remove the cutout template and ip to
the side that corresponds with your product’s part
number.
Step 4 - With a 1/2” drill bit, drill a hole in each
corner, being careful not to splinter the wood on
the inside of the drawer box. Using one of the 1/2”
holes, insert a jigsaw and then make the required
cutouts in the drawer box.
of space
needed behind
drawer box
2”
2”
of space
needed behind
drawer box
of space
needed behind
drawer box
STYLE DRAWER 21 BLADE
& 21 BLADE DUO
STYLE DRAWER 24 BLADE
& 24 BLADE DUO
STYLE DRAWER FLUSH
5”
≥14.5”
≥13.5”
≥12”
min drawer box width for 24 Flush
min drawer box width for 21 Flush
≥10.5”
min drawer box width for 18 Flush
Step 5 - Reinstall the
drawer box and slide the
Style Drawer receptacle
box through the cutout.
Secure it with the 4 wood
screws provided.
Note for Blade outlets: Attach
the mounting ange before
securing the receptacle box.
min drawer box width if drawer box height is ≥ 5.25”
min drawer box width if drawer box height is ≥4”
≥16.25”
≥16”
min drawer box width if drawer box height is ≥ 5.25”
min drawer box width if drawer box height is ≥4”
≥17.75”
• It is the installer’s responsibility to make sure that
power supplied to the junction box conforms to all
applicable building codes and standards.
• The Style Drawer series outlets must be connected
to a 20A circuit using 12 AWG wire.
Style Drawer
Blade™
and Flush™
Installation
Instructions
STYLE DRAWER
BLADE PART #:
0290-00324
0290-00324-I
0290-00324-U
0290-00324-UI
0290-00321
0290-00321-I
0290-00321-U
0290-00321-UI
For Style Drawer Blade installations with optional
Interlock Box, see addendum installation manual
before starting the outlet installation.
Tools Needed:
• Jigsaw
• Drill
• Measuring Tape
• Screwdriver
• Square
• Pencil
• Cutout Template
Time Required - 30 min
STYLE DRAWER
BLADE DUO PART #:
0290-20324
0290-20324-I
0290-20324-U
0290-20324-UI
0290-20321
0290-20321-I
0290-20321-U
0290-20321-UI
STYLE DRAWER
FLUSH PART #:
0290-00033
0290-00033-U
0290-00032
0290-00032-U
0290-00050
0290-00050-U
CUTOUT TEMPLATE
for Style Drawer
Blade & Flush
STYLE DRAWER
BLADE PART #:
0290-00324
0290-00324-I
0290-00324-U
0290-00324-UI
0290-00321
0290-00321-I
0290-00321-U
0290-00321-UI
STYLE DRAWER
FLUSH PART #:
0290-00033
0290-00033-U
0290-00032
0290-00032-U
0290-00050
0290-00050-U
FOR ACCURACY SCALE PRINTER TO 100%