F-01E INSTRUCTION MANUAL ’12.
Thank you for purchasing "F-01E". Before using F-01E, read this manual to ensure safe use and handling. About manuals for F-01E The operations of F-01E are described in this manual, "使いかたガイド (Guide)" (installed in FOMA terminal) and "Instruction manual (detailed version)" (in pdf format, Japanese only). Instruction manual (this manual) This manual provides information about screens and operations of basic functions.
Contents Part names and functions ............... Open assist button........................... FOMA terminal ................................. 2 4 5 Precautions (Always follow these directions) ..................................... Handling precautions....................... Waterproofness/Dustproofness ..... 6 15 20 Before Using ..................................... Screen Explanation .......................... Character Entry ................................ 25 28 32 Sound/Screen Setting ..........
Part names and functions Part names of F-01E and major functions assigned to each part are as follows.
To use the function with *, press the key for 1 second or more. Covering around the antenna by the hand may affect the quality. f 1Seg/FM transmitter antenna is built-in Covering around the antenna by the hand may affect the quality. g Light that turns on when receiving a call or while charging h Sub-display i GPS antenna is built-in Covering around the antenna by the hand may affect the quality. j FOMA antenna is built-in Covering around the antenna by the hand may affect the quality.
o (Side key) Light sub-display, switch display Z (Side camera key) Activate movie shooting, record video during 1Seg watching* SD Adjusting volume S stops ring alert, alarm, vibrator or activates quick message*, D conducts mail/message inquiry*, etc. Introduction Connection of Stereo Earphone Set 01 (Optional) for external connection jack Open assist button The FOMA terminal can be opened easily only by pushing the dedicated button.
FOMA terminal ･ Maintain a separate record of the data LAN System. ･ Because your FOMA terminal uses wireless transmission, it may not function in locations where it is difficult for radio waves to penetrate, such as tunnels, underground passages and some buildings, in areas where radio waves are weak, or out of service area. Even when you are high up in a tall building or condominium and nothing blocks your view outside, your FOMA terminal may not be able to receive or transmit signals.
Precautions (Always follow these directions) ・ Before using your FOMA terminal, or when Introduction necessary, read the precautions below to ensure safe use and handling. After reading this manual, keep it carefully. ・ These precautions are intended to protect you and others around you. Read and follow them carefully to avoid injury, damage to the product or damage to property.
Handling FOMA terminal, battery pack, adapter, desktop holder and docomo mini UIM card (common) DANGER May cause fire, burns, injuries, electric shock. Do not cover or wrap the terminal with a blanket, etc while using or charging. Don’t May cause fire or burns. May cause fire, burns or injuries. Do not put the terminal into heating cooking device such as microwave oven Don’t or high-pressure container.
Do Children using the equipment should be instructed in proper operation by an adult. Do not allow them to use the equipment without adult supervision. Do not turn on the light by getting the lighting part closer to other person's Don’t eyes. When shooting infants, keep at least 1 m away from the object. May cause injuries. Introduction Store the equipment out of reach of small children. Do Do May be accidentally swallowed or cause injuries.
Do When you talk by setting handsfree or ring alert is sounding, keep FOMA terminal away from your ear. And, when connecting the earphone/ microphone etc. to the FOMA terminal and play a game, music, etc. adjust the volume moderately. Do Do Do Do CAUTION Do not swing FOMA terminal by its strap etc. Don’t May cause harmful effect on electronic medical equipment etc. Do Turn FOMA terminal OFF near highprecision electronic control equipment or electronic equipment using lowpower signals.
If the display part is accidentally broken and the liquid crystal leaks out, do not Don’t make the substance contact with your skin of face or hands. Introduction May cause loss of sight or skin problems. If the liquid crystal gets into your eyes or mouth, rinse it with clean water and see a doctor immediately. And, if the liquid adheres to skin or clothing, use alcohol etc. to wipe it off, then wash with soap.
WARNING If the battery pack seems to have abnormalities such as deformation or Don’t scratches due to falling, never use it. Handling adapter and desktop holder WARNING May cause battery pack to ignite, burst, heat or leak. The vapors from leaking battery pack fluid may ignite or explode. Be careful not to let your pet bite the battery pack. Do May cause battery pack to ignite, burst, heat or leak. CAUTION Don’t Do May cause fire, burns, electric shock.
Do not touch the adapter cord, desktop holder or outlet with wet hands. No wet hands May cause fire, burns, electric shock. Do Introduction Only use with the specified power source and voltage. When charging FOMA terminal overseas, use AC Adapter for global use. If incorrect voltage is used, this may cause fire, burns or electric shock.
Handling mobile phones near electronic medical equipment ■These precautions are based on the guidelines produced at the Electromagnetic Compatibility Conference Japan, regarding the protection of electronic medical equipment from radio waves emitted by mobile phone units. Do Do Do Material list ･ Do not bring FOMA terminal into operating rooms (ORs), intensive care units (ICUs) or coronary care units (CCUs). ･ Turn FOMA terminal OFF in hospital wards.
Part Material Surface treatment Introduction Camera lens, camera panel Acrylate resin UV hard coating Light lens part Acrylate resin Engraving Side keys PC resin UV hard coating Keypad Urethane acrylate resin UV hard coating Open assist button PC resin UV hard coating Hinges PC resin UV hard coating External Body connection Flexure jack cap PC+ABS resin UV hard coating Elastomer resin None Water stop PC resin None Tabs PC resin None O ring Silicon rubber None External connecti
Handling precautions General ・ F-01E is waterproof/dustproof, however, do not allow to FOMA terminal or the battery. - If FOMA terminal is crammed into a brimming bag or placed in a pocket and sat on, display, internal PCBs or battery pack may be damaged or malfunction. And, if external devices are plugged into the external connection jack (earphone/microphone jack), the breakage of the connector or malfunction may result. ・ Do not rub or scrape the display with a metal piece etc.
・ Do not leave FOMA terminal with the camera in areas Introduction 16 under strong direct sunlight. - May cause discoloring or burn-in of elements. ・ Use FOMA terminal with the external connection jack cap closed. - Dust and/or water brought into FOMA terminal cause troubles. ・ Do not use FOMA terminal with the back cover removed. - May cause removal of battery pack, malfunction or damage. ・ Do not put extreme thick sticker on the display or keypad face.
docomo mini UIM card ・ Do not use excessive force to install/remove docomo a bc 2.4FH1 mini UIM card. ・ Note that DOCOMO assumes no responsibility for Bluetooth devices ・ This FOMA terminal is equipped with the security features, that are compliant with Bluetooth standards for communication via Bluetooth. However, depending on the settings, there may not be enough security. Be aware of security risks when using Bluetooth.
Wireless LAN (WLAN) ・ Wireless LAN (WLAN) exchanges information using Introduction radio waves, and allows you to freely establish LAN connection if you are within an area where radio wave reaches. On the other side, if you communicate without appropriate security settings, communications may be intercepted or hacked by malicious parties. It is recommended to make necessary security settings on your judgement and responsibility.
FeliCa reader/writer ・ FeliCa reader/writer function of FOMA terminal uses weak waves requiring no licenses for radio stations. ・ It uses 13.56 MHz frequency band. When using other FM transmitter ・ FM transmitter of FOMA terminal uses weak waves requiring no licenses for radio stations. ・ It uses 77.4 - 85.0MHz frequency band. To use it, set frequency not to common to FM radio station of the area you use to avoid affecting FM radio users in neighborhood. remodeled terminal violates the Radio Law.
Waterproofness/Dustproofness Introduction F-01E provides waterproofness of IPX5*1, IPX8*2 and dustproofness of IP5X*3 with firmly closing the external connection jack cap and installing the back cover in a locked state. *1 IPX5 means that a phone keeps functioning after applying a jet flow of 12.5 L/min. from every direction from a distance of approximately 3 m for at least 3 minutes using water nozzle in 6.3 mm inner diameter.
To ensure waterproofness/dustproofness Groove After using the external connection jack, close the cap as the direction shown in the illustration, and make sure that the cap is completely closed without slack by pushing the tabs in. To keep the terminal waterproofness/ dustproofness, replacement of parts is required every 2 years regardless of whether the terminal appears normal or abnormal. DOCOMO takes the FOMA terminal to replace the parts as a chargeable service.
Important precautions Do not perform actions shown in the illustrations below. Introduction Using Soap/Detergent/ Bath powder Washing with brush/sponge Machine-washing Applying strong water flow Soaking in ocean water Using in hot spring Observe the following precautions to use FOMA terminal properly. ・ Accessories and optional devices are not waterproof/dustproof. When watching 1Seg etc.
Washing FOMA terminal With pressing and holding the external connection jack cap not to open, wash the terminal in tap water without rubbing hard Press here Draining water from FOMA terminal Introduction When FOMA terminal is wet, water may flow out after wiping it off; drain the water in the following steps. a Wipe off moisture on the FOMA terminal surface and back side with dry, clean cloth etc.
c Press lightly the FOMA terminal against dry, clean cloth etc. about 10 times to wipe off water remaining in the microphone, earpiece, speaker, keypad, hinges or charging jack, etc. Introduction 24 d Wipe off water drained from FOMA terminal with dry, clean cloth etc., and dry naturally. ･ Water, if any, remaining in FOMA terminal may ooze up after wiping off. ･ Do not wipe off water remaining in gaps directly with a cotton swab etc. Charging Check the following before and after charging.
Before Using Attaching docomo mini UIM card/battery pack After turning power OFF, close FOMA terminal and hold it in your hand so that you can properly attach docomo mini UIM card/battery pack.
Before Using Charging The battery pack does not have a full charge at time of purchase. Use AC adapter for FOMA terminal to charge the battery before using FOMA terminal.
Before Using Power ON - Default setting Initial setting is an operation when FOMA terminal is turned ON for the first time. a f (2 sec. or more) The Initial setting screen appears. b Set required itemseC [Complete] c On a confirmation screen of software update function, geOn the confirmation screen of Error info send set., g Caller ID notification Set whether to notify your phone number (caller ID) to the other party's terminal when making a voice call.
Screen Explanation Viewing display New arrival information and current state can be checked by the icon appearing on the screen. Major icons are as follows. a Status area Status icons are displayed. Select an area on the stand-by screen to display icon details screen.
bUpdate notification of MyFACE⇒P31 cPedometer/ACT monitor Steps and activity amount of the day are displayed. d Machi-chara Characters moving about the screen and giving messages. In addition to the preinstalled characters, you can obtain characters by downloading. e New arrival Starting from the left, missed call, recorded message, message in voice mail service, unread mail, unread ToruCa, i-αppli call Select an arrival information etc.
Screen Explanation Basic operations for screen and keys Menu operation On the stand-by display, press m and then perform the functions from the menu. You can select a menu item with shortcut operations, which use the keypad, etc. or with multi-cursor key operation, which uses the multi-cursor key to move the cursor.
Screen Explanation docomo Palette UI MyFACE In the right and left area of the stand-by display, up to 12 MyFACEs downloaded from sites, etc. can be pinned. Screen Explanation 使いかたガイド (Guide) You can check outline of function, operations or troubleshooting. (In Japanese only) a mef Toole# GuideeSelect a search method a l or r Switch screens one after another in the same way to display MyFACE you want to use.
Character Entry Entering characters 5-touch input and conversion 5-touch input is an input method to switch a character by pressing a key repeatedly. a Enter character on the character entry screen Basic Operation When a character is entered, the cursor automatically moves in a regular interval. To quickly enter characters assigned to an identical key consecutively, press r.
Text input Set a text input method or operation during text entry. a meh Settinged Text display/ inputec Text inputea Text input methodeSet required itemseC [Set] Useful functions on the entry screen Entering common phrases a m [Submenu]ed Quote phrase/ dataeb PhraseeSelect phrase typee Select a phrase a m [Submenu]ed Quote phrase/ datae0 Pict/Symbol/Smileyec SmileyeSelect a smiley typeeSelect a smiley Copying/Cutting, pasting characters a m [Submenu]ec Copy/Cut/etc.
Sound/Screen Setting Sound settings You can set tones, such as changing a ring alert, adjusting the volume, or muting the sound emitted from FOMA terminal. Ring tone You can set your favorite melody, etc. for a ring alert.
Sound/Screen Setting Setting display Stand-by display setting You can change the default stand-by display. Setting an image a meh Settingea Screen/Display eb Stand-by display settingea Image/i-αppliea Set image b Select a foldereMove the cursor to an imageeC [OK]e"Yes" Display light You can set the brightness of screen and Light time-out. a meh Settingec Backlight/ Illuminationea Display lighteSelect an itemeSelect a time or operation a s (1 sec. or more) Canceling Privacy view : s (1 sec.
Setting Machi-chara Basic Operation You can set a character to be displayed on the stand-by display. A message can be changed to the speech in Machi-chara talk expression. You can also use Friendly message support Machichara that displays a message according to the FOMA terminal status or content of entered text. "リーフロボット (Leaf robot)" and "くーまん (Kuman)" stored by default are the friendly message support Machi-chara.
Sound/Screen Setting Light setting Indicator light You are notified of missed call or unread mail (including SMS) by the indicator light. Point ･ The indicator light blinks at approximately 10 seconds interval. However, when you receive information with the FOMA terminal closed or you open the FOMA terminal and close without checking the arrival information, the indicator light blinks at approximately 30 minutes interval.
Lock/Security Security codes Security codes vary by functions. Security code protects personal information. Be careful about handling the security code. Terminal security code (Default : 0000) Basic Operation The code is the security code to be used when changing settings or deleting all the items at once. To change the code, perform the following operation.
To change either code, perform the following operation. When changing PIN1 code, set PIN1 entry ON/OFF to "ON" in advance. a meh Settingef Lock/Securitye i UIM settingea Change PIN1 code or b Change PIN2 codeeAuthenticate b Enter the current PIN codeeEnter a new PIN code in New PIN code field and New PIN code - check fieldeC [Save] power on, mehficaeEnter PIN1 code, and then set PIN1 entry ON/OFF to "ON".
Lock/Security Various lock functions All lock ✜ Unoperated lock set Menu operation is unavailable. You can use only a part of operations such as answering calls, receiving mails, turning power ON/OFF. Activate : mehfabeAuthenticate Deactivate : Enter the terminal security code (When the fingerprint authentication is set, meAuthenticate) Lock key operation when no operation is performed for a certain period of time.
Lock/Security Lock/Security Incoming call restriction Resetting to default Call rejection setting Call reject setting allows you to reject calls from phone numbers not saved in phonebook and reject or accept calls from the specified numbers. In addition, you can set a receiving operation for each reason for hiding caller ID.
Call Telephone Making a call/videophone call Entering a phone number a Enter a phone number including area code (Up to 80 digits)en (voice call) or C (videophone call)eWhen ending the call, f Point ･ Do not cover the microphone during a call. Using phonebook a ueSearch phonebook Connect The phonebook list search result of the Show all names is displayed by default. You can switch lines by h or switch the pages by a / I.
Koe-no-Takuhaibin Koe-no-Takuhaibin is a service sending messages using voice call. You can record or play messages between FOMA terminals without calling a party. You are notified by record notification SMS when a message is recorded, and by play notification SMS when the party plays a message (when the party sets play notification to on. It is set to on by default). For details, refer to NTT DOCOMO website. Recording a message Record a message in the Koe-no-Takuhaibin service center.
Call Telephone Receiving a call/videophone call a Receive You are notified of an incoming call with ring alert, light alert, etc. On the display, the phone number appears when caller ID is sent, and caller's name appears when phone number is saved in the phonebook. When caller ID is not sent ,the reason (Anonymous, Payphone or Unavailable) appears.
Call Telephone When you cannot answer a call Record message Public mode When Record message is set to "ON", a greeting message is played and the caller can record message when you cannot answer the call. Public mode is an automatic answering service putting emphasis on manners in a highly public place or when driving a car. a meg TEL functioneb Record message/Voice memoed Record messageea ON Public mode (Drive mode) appears on the stand-by display.
Call Telephone Network Services Service Voice Mail Service Missed Call Notification Service Application Monthly charge Required Charged Not required Free Service Call Waiting Service Required Charged Call Forwarding Service Required Free Nuisance Call Blocking Service Not required Free Not required Free Not required Free Not required Free Caller ID Notification Service Connect Caller ID Display Request Service English guidance Multi Number 2in1 Koe-no-Takuhaibin Required Charged Requ
Call Telephone Emergency call You can make the following emergency calls from the FOMA terminal. Police 110 Fire and ambulance 119 Marine emergencies 118 ･ This FOMA terminal supports "Emergency terminal, inform them that you are calling from a mobile phone and give your phone number and your current location precisely since the police or fire department has to call you back for confirmation.
Call Telephone Using overseas You can talk with FOMA terminal and use i-mode overseas. 3G GSM/ GSM GPRS Connect ✜ International Roaming (WORLD WING) i-Widget*5 ○ ○ International roaming (WORLD WING) is a service that allows you to make voice calls and access imode using network of telecommunications carriers affiliated with DOCOMO overseas. Before using this service, check its subscription status. For details, contact "General Inquiries" on the last page of this manual.
Making a call from the country you stay You can make a voice call or videophone call from overseas using international roaming service. Making an international call a 0 (1 sec. or more) "+" is entered. b Enter "Country code (for Japan, 81)phone number without the leading 0 of Area code (City code)"en (voice call) or C (videophone call) In some countries and areas such as Italy, "0" is required.
Mail Sending i-mode mail/Sending SMS Sending i-mode mail Only by subscribing to i-mode, i-mode mails can be exchanged not only with i-mode compatible terminals but also via Internet. ･ For details of i-mode mail, refer to "Mobile Phone User's Guide [i-mode]". a aea [Write] b Enter an address, title and texteC [Send] When sending is completed correctly, the mail is automatically saved in a folder of Outbox.
Mail Deco-mail/Decome-Anime Deco-mail You can change a font size or background color, or insert still images, Deco-mail picture or Deco-mail pict. Specifying decoration before entering characters Decome-Anime You can create more expressive Deco-mail using templates made with Flash graphics.
Mail Receiving i-mode mail No specific operations or settings are required for receiving mails (mail automatic reception). a Receive i-mode mails Point ･ By selecting a mail and then pressing C, you can reply easily using stored common phrases (Quick reply). Blinking Checking new mail/message You can make inquiry for any i-mode mail or MessageR/F delivered while you were out of service area or the power was turned OFF. a a (1 sec.
Mail Phonebook Early warning "Area Mail" Phonebook new entry This is a service that you can receive emergency earthquake flash report etc. delivered by the Meteorological Agency. i-mode subscription is not required. There are two phonebooks: the FOMA terminal phonebook and the UIM phonebook. Receiving Area Mail When an Area Mail is received, turns on, and you are notified of reception with blinking light, the dedicated buzzer, dedicated ring alert or vibrate alert.
i-mode/Full Browser Displaying i-mode site/website With i-mode, you can use services such as site connection, Internet connection or i-mode mail by the display of i-mode compatible terminal. You can use Full Browser to display websites created for a PC. ･ i-mode is a charged service requiring subscription. For details, refer to "Mobile Phone User's Guide [i-mode]". ･ The contents of sites and Internet websites are Search generally protected by copyright laws.
Viewing and operating screen Bookmark You can bookmark frequently visited sites or websites to quickly display them the next time you want to visit. Saving : When a site or website is displayed, m [Submenu]eabe"OK"eSelect a saving folder Displaying : mebbeSelect a foldereSelect a bookmark Status, title/URL Pointer * Search Scrolling up and down : SD or k Scrolling up and down continuously* : k (1 sec.
i-channel Using i-channel Search 56 i-channel is a service that news, weather information, etc. is distributed to the i-channel compatible terminal. (In Japanese only) The autoreceived information appears in the ticker on the stand-by display. Press c to display the channel list. ● Basic Channel The channel is provided by DOCOMO, and the packet communication fee for automatically updating the distributed information is not charged.
Map/GPS Using Map/GPS function ･ This function is unavailable as a navigation ･ ･ ･ Map/Navigation You can start GPS compatible i-αppli to display maps after positioning location or navigate. a mei Map/Overseasea Map or b Navigation Point ･ i-αppli set in Select map in Map setting starts. "地図 アプリ (Map Application)" is set by default. Position location You can check where you are.
Map/GPS AUTO-GPS Search Your current location or information measured by Pedometer/Activity monitor is automatically sent to service providers on a regular basis (approximately once in every 5 minutes), which allows you to services that deliver information about the weather or shops around where you are, or sightseeing information. (In Japanese only) ･ To use an AUTO-GPS compatible service, set AUTO-GPS service information from its AUTOGPS compatible i-αppli.
Camera Shooting still images/moving pictures Viewing shooting screen a b c d e f Shooting still images aC b Point the camera at an object, g [ or Z ] When Auto save mode is "OFF", a confirmation screen for saving appears.
･ If the inside temperature of the FOMA terminal becomes high because of heat during camera operation, the recording or camera function may be deactivated before the maximum recording time to protect the FOMA terminal. In this case, wait until the temperature of the FOMA terminal drops and use the camera function. This is normal.
1Seg Watching 1Seg "Auto setting", make sure to register them to the channel list. For details on rearrangement of Digital Terrestrial Television Broadcasting, refer to the following websites. 総務省テレビ受信者支援センター（デジサポ） (DTV Support Center, Ministry of Internal Affairs and Communications) チャンネル変更コールセン ター (Channel change call center) Phone number : 0120-922-303 From a PC : http://www.digisuppo.jp/repack/ (In Japanese only) From i-mode : http://digisuppo.jp/m/index.
b Select an areae"Yes" Watching 1Seg a T (1 sec. or more) Viewing and operating the watching screen You can watch 1Seg in full screen, or divide the screen to watch the data broadcasting. Enjoy When Switch active operations in Image & Effect is "OFF", the following operations are available.
Music MUSIC Player You can play Chaku-uta full downloaded from a site and Windows Media Audio (WMA) files imported from music CDs, the Internet, etc. to a PC. And Uta-moji lyrics downloaded from a site can be displayed on the player screen by setting Link lyrics & song. * For details of MUSIC Player, refer to NTT DOCOMO website. For Windows Media Player, contact the manufacturer of your PC. Saving WMA file on a PC to microSD card For connection to a PC, FOMA USB Cable (optional) is required.
i-αppli i-αppli/i-Widget Enjoy 64 i-αppli is a software for i-mode compatible terminals, which updates the information of stock price or weather automatically, or provides games that can be played without connecting to the network. i-Widget is a convenient function that allows you to easily access frequently-used contents and tools (Widget Appli) such as calculator, clock, memo, stock price information, etc.
i-motion/Movie Playing i-motion/movie You can obtain i-motion/movie (images, sound, etc) from sites or websites. ✜ Playable i-motion Type Playing action Standard While the i-motion data is type (can downloaded, it is played. be saved*) ･ The downloaded i-motion can be operated in the same way as the imotion which is played after entire data is downloaded. After the entire i-motion data is downloaded, it is played. Streaming While the i-motion data is downloaded, it is played.
Osaifu-Keitai Using Osaifu-Keitai More Convenient 66 ■Osaifu-Keitai Just hold the FOMA terminal over the reader in store etc. to use "おサイフケータイ対応サービス (Osaifu-Keitai compatible service)" that allows you to use the terminal for payment or as coupon, or "かざしてリンク対応サービス (Hold to link compatible service)" that can access information by holding over home electrical appliance, smart poster, etc. Additionally, you can deposit e-money or check the balance, or check points via network.
i-concier Using i-concier ･ Automatic updating i-schedule/memo/ToruCa/ phonebook, etc. requires a packet communication fee separately. ･ For details, refer to "Mobile Phone User's Guide [i-mode]". Receiving information Information is sent automatically. a Information is received lights on in the status area with light or ring alert for notification.
Convenient tools Shabette-Kensaku Convenient tools Voice quick start You can use i-mode search by speaking a keyword. (In Japanese only) ･ A packet communication fee is charged for using. When you do not know a desired menu of function or you want to activate the function quickly, the function can be activated by voice sound input from the stand-by display. (In Japanese only) a U (1 sec. or more) a n (1 sec. or more) The FOMA terminal vibrates.
Convenient tools Schedule Manage memos by Schedule or check a downloaded i-schedule. (In Japanese only) The view and function of schedule varies by the schedule type. "Normal" in which you can manage the schedules linking with i-concier or the memo list is described here.
Convenient tools Bluetooth You can establish a wireless connection between FOMA terminal and a Bluetooth device. For operations of the Bluetooth device, refer to the operation manual of your Bluetooth device. * Wireless communication is not guaranteed for all Bluetooth devices. ✜ Compatible version Bluetooth standard Version 2.
Convenient tools Wi-Fi You can make Wi-Fi connection in Access point mode (Base unit) or Client mode (Sub unit). ･ The FOMA terminal is compatible with wireless LAN standards of IEEE802.11b, IEEE802.11g and IEEE802.11n (client mode only). Base unit and client device should be compatible with the same standard to connect. ･ Note that using Wi-Fi makes battery consumption faster.
Setting Access point (APN) Set an access point to use for external connection in AP mode. a mef Toole"Wi-Fi"eb Access point (main)ec Access points (APN) b Select an access point (APN)eC [Save] Select "" and press a to add new APN. Point ･ mopera U is registered by default. "mopera U 128k" is set as the access point (APN).
Data Management Using microSD card ✜ Precautions on using microSD card ･ The data saved from another device such as a PC may not be displayed or played in FOMA terminal. And the data saved from FOMA terminal may not be displayed or played in other device.
Data Management Exchanging data between FOMA terminal and microSD card Copying images to microSD card a mee Data Boxea My picturee Select a foldereMove the cursor to data When the folder list of microSD card, select "→phone". b m [Submenu]ee Move/Copye c Copy to microSDeSelect copying method Select image to copy selected itemeC, authenticate to copy all data in a folder. c "Yes" More Convenient Move the cursor to a folder to copy an iteme Press C.
Data Management Infrared communication/iC transmission You can send/receive data to/from devices such as FOMA terminal supporting infrared communication function or iC transmission function. Infrared data port 15° 15° Approx. 20 cm or less iC transmission Point ･ When sending/receiving all data items, the sender and receiver need to determine a 4-digit authentication password in advance. For infrared communication, the receiver's terminal must be ready for communication first.
Data Management Connecting to a PC More Convenient You can connect FOMA terminal to a PC to transfer WMA files or images in the microSD card. Also, connecting to the Internet for data communication is available. ･ FOMA USB Cable with Charge Function 02 (optional) or FOMA USB Cable (optional) is required. ･ To perform data transfer using data communication or DOCOMO keitai datalink, install FOMA communication configuration (driver) on a PC. For details, refer to "Manual for PC Connection".
Support Troubleshooting Check for the necessity of software update first, and update the software if necessary. ⇒P81 When checking the following items not to improve the state, contact "Repairs" on the last page of this manual (in Japanese only) or DOCOMO-specified repair office. ✜ Terminal operation ● FOMA terminal cannot be turned ON. ･ Is the battery pack installed correctly? ･ Is the battery exhausted? ● The FOMA terminal cannot be charged (the light does not turn on while charging).
Others 78 ● FOMA terminal etc. become hot while operating/ charging. While operating or charging, or if you use i-αppli, videophone call, 1Seg watching, etc. for a long time while charging the battery, FOMA terminal, battery pack and adapter may become hot. There is no problem about safety and continue to use it. ● The clock is not on time. The clock time may become wrong while turning on the power for a long time.
Support Warranty and After-Sales Service Warranty ･ FOMA terminal is provided with a written warranty. Make sure that you receive it. Check the written contents and items such as "販売店 名・お買い上げ日 (Shop name/date of purchase)" and keep it in a safe place. If it does not contain the necessary information, immediately contact the shop where you bought it. The warranty is valid for a period of one year from the date of purchase.
✜ Notes ･ Do not modify FOMA terminal or its accessories. ･ ･ ･ ･ Others 80 ･ - Repair may be refused depending on the nature of modification. The following cases may be regarded as modifications. - A sticker etc. is put on the display or keypad part - FOMA terminal is embellished with adhesive material etc. - Exteriors are replaced with other than DOCOMO's genuine parts - Repair of failures or damage caused by modification is charged even during the warranty period.
Support Updating software This function allows you to connect the network and check if software in the FOMA terminal needs to be updated, if software update is necessary, download a part of software using packet communication and update the software. When software update is required, information is posted in "お客様サポート (user support)" on NTT DOCOMO website or iMenu (in Japanese only). Software may be updated in 3 methods: "Autoupdate", "Immediate update" and "Reserved update".
Support Scanning function (Security Scan) For the data or programs that are imported to FOMA terminal, this function detects data and deletes data or inhibits activation of applications that may cause troubles. ･ The Scanning function provides a certain countermeasure against invasion of data which causes some trouble in the mobile phone, when viewing website, receiving messages, etc.
Support Options and related devices ･ Remote controller with microphone F01*2 ･ Earphone Terminal P001*5 ･ Wireless Earphone Set P01 ･ Wireless Earphone Set 02/03 ･ Bluetooth Headset F01 ･ AC adapter for Bluetooth Headset F01 ･ FOMA AC Adapter 01 for Global use*1 ･ FOMA Indoor Booster Antenna*6 ･ FOMA Indoor Booster Antenna (Stand Type)*6 ･ Bone conduction microphone/receiver 01*2/02 ･ FOMA eco Solar Panel 01 *1 When using FOMA terminal overseas, use the adapter plug that is suitable for use in your travel
Appendix Menu list ･ Menu list for the case Select startup menu is set to "Basic menu" is described. ･ Menus indicated in red can be restored to the default by executing Reset (including the menu whose partial sub content menu will be reset to the default).
i-αppli setting Sound effect volume Melody Software info disp.
Guide Bluetooth Record message/Voice memo Record message list Accept registered Voice memo list Receive data Record voice memo Send all via BT List/cnnct/discnct Record message Dialed/Received calls Register new dev Bluetooth Power ON/OFF Wi-Fi F-LINK/Home media Received calls Redial Dial/Receive call setting Nuisance call blocking service Bluetooth setting Caller ID request Client mode (sub) Caller ID notification Access point (main) Arrival call act F-LINK Dial call detailed setting H
2in1 2in1 mode switching ■Setting Ph.
Lock/Security Locks Other setting Initial setting Code & Fingerprint Delete all data Security indicator Reset Kid-safe mode Software update Scanning function Error info send set. Password manager Check remote setting microSD password setting Memory status UIM setting Side key shortcut Call rejection setting IC card lock Battery Motion sensor Kisekae/Themes Kisekae Tool Caller/Sender info Style theme eco mode setting Timed theme eco mode auto-start set.
Overseas network search 3G/GSM setting ■i-concier Network search setting i-concier PLMN setting Display operator name setting Display area status Re-search icon display setting Overseas setting Inquiries(overseas) Barring incoming call when roaming Missed call notification for roaming ■Profile Profile ■Osaifu-Keitai IC card content DCMX ToruCa IC card lock setting IC card lock Roaming guidance Timed lock International dialing assist Programed activation IC lock(power-off) i-mode service settin
Appendix Main specifications ■Phone F-01E Size Approx. 111 mm (H) 50 mm (W) 11.7mm (T) (Thickest part : Approx. 16.2mm) Weight Approx. 110 g (with battery) Continuous FOMA/3G stand-by time*1, 2, 3 GSM Stationary (Auto) : Approx. 550 H Continuous FOMA/3G call time*2, GSM 3, 4 Voice call : Approx. 210 min. × × 1Seg watching time*2, 5 Moving picture shooting time*8 Others Type Display : TFT 16,777,216 colors Sub-display : Organic EL 1 color Size Display : Approx. 3.
*1 Continuous stand-by time indicates the estimated time when FOMA terminal is closed and able to receive radio waves normally. Stationary continuous stand-by time indicates the average utilization time FOMA terminal is closed and able to receive radio waves normally remains stationary.
Appendix Specific Absorption Rate (SAR) of Mobile Phones Others 92 This model F-01E mobile phone complies with Japanese technical regulations and international guidelines regarding exposure to radio waves. This mobile phone was designed in observance of Japanese technical regulations regarding exposure to radio waves (*1) and limits to exposure to radio waves recommended by a set of equivalent international guidelines.
This mobile phone complies with the EU requirements for exposure to radio waves. Your mobile phone is a radio transceiver, designed and manufactured not to exceed the SAR* limits** for exposure to radio-frequency(RF) energy, which SAR* value, when tested for compliance against the standard was 0.665W/kg for HEAD. While there may be differences between the SAR* levels of various phones and at various positions, they all meet*** the EU requirements for RF exposure.
Before a phone model is available for sale to the public, it must be tested and certified to prove to the FCC that it does not exceed the limit established by the U.S. government-adopted requirement for safe exposure. The tests are performed on position and locations (for example, at the ear and worn on the body) as required by FCC for each model. The highest SAR value for this model phone as reported to the FCC, when tested for use at the ear, is 0.561W/kg, and when worn on the body, is 0.599W/kg.
Important Safety Information Warning: To prevent possible hearing damage, do not listen to high volume levels for long periods. Appendix Export Administration Regulations This product and its accessories may be under coverage of the Export Administration Regulations of Japan ("Foreign Exchange and Foreign Trade Control Laws" and the related laws and regulations). And, they are also under coverage of Export Administration Regulations of the U.S.
Appendix Intellectual Property Right Copyrights and portrait rights Except for the case protected by copyright laws such as personal use, use of FOMA terminal to reproduce, alter, or publicly transmit recorded pictures or sounds, or copyrighted text, images, music or software downloaded from websites without the copyright holder's authorization is prohibited. Note that taking photos or recordings at some demonstrations, performances or exhibitions may be prohibited even when only for personal use.
･ "Multitask" is a registered trademark of NEC ･ ･ ･ ･ ･ ･ ･ ･ This product contains software licensed by Symbian ･ ･ ･ ･ ･ ･ ･ ･ ･ ･ ･ ･ Foundation Limited. Symbian is a registered trademark of Symbian Foundation Limited. "Privacy mode" is a registered trademark of FUJITSU LIMITED. "Uni-Type" is a universal designed font jointlydeveloped by LIM Corp., Ltd. and Faculty of Engineering, Chiba University. Uni-Type is a registered trademark of LIM Corp., Ltd.
Others ･ This product is licensed based on MPEG-4 Visual ･ This product contains a module developed by the Independent JPEG Group. ･ FeliCa is a contactless IC card technology developed by Sony Corporation. ･ OMRON Corporation's Mobile OmCR is used for a character recognition engine. ･ This product contains software licensed based on Apache License V2.0. and altered as necessary by NTT DOCOMO, INC.
･ The HMM-Based Speech Synthesis Engine embedded in this product uses the Simplified BSD License. ------------------------------------------------------------------------------------ The HMM-Based Speech Synthesis System (HTS) hts_engine API developed by HTS Working Group http://hts-engine.sourceforge.
Others 100 <三省堂 (SANSEIDO)> デイリー日仏英・仏日英辞典（村松定史監修／三省堂 編修所編）(Daily Japanese-French-English/FrenchJapanese-English dictionary) デイリー日独英・独日英辞典（渡辺学監修／三省堂編 修所編）(Daily Japanese-German-English/GermanJapanese-English dictionary) デイリー日中英・中日英辞典（池田巧監修／三省堂編 修所編）(Daily Japanese-Chinese-English/ChineseJapanese-English dictionary) デイリー日西英・西日英辞典（上田博人、アントニ オ・ルイズ・ティノコ監修／三省堂編修所編）(Daily Japanese-Spanish-English/Spanish-JapaneseEnglish dictionary) デイリー日伊英・伊日英辞典（藤村昌昭監修／三省堂 編修所編）(Daily Japanese-Italian-English/ItalianJapanese-Eng
Index A D AC adapter ...................................................... 26 Access point (main)........................................ 71 Adjust volume................................................. 34 After-Sales Service ......................................... 79 Alarm ............................................................... 69 All lock ............................................................. 40 Attachments ................................................... 50 AUTO-GPS.................
I i-αppli .............................................................. 64 IC card lock...................................................... 40 iC transmission ............................................... 75 i-channel .......................................................... 56 Icon .................................................................. 28 i-concier ........................................................... 67 i-mode fault diagnosis site ............................ 80 i-mode password....
Receiving a videophone call .......................... 44 Receiving i-mode mail.................................... 52 Record message ............................................. 45 Recording reservation.................................... 62 Redial ............................................................... 42 Replying to mail.............................................. 52 Reset ................................................................ 41 Ring tone ............................................
Please ask checking/changing subscription detail, application of various services and request of various information materials online. From i-mode iMenu ⇒ お客様サポート (Support) ⇒ お申込・お手続き (Application/Procedures) ⇒ 各種お申込・お手続き (Various application/Procedures) No packet communication charges From PCs * In Japanese only My docomo (http://www.mydocomo.com/) ⇒ 各種お申込・お手続き (Various application/Procedures) * In Japanese only * You need your "Network security code" to use the site from i-mode.
General Inquiries 0120-005-250 (toll free) * Service available in: English, Portuguese, Chinese, Spanish, Korean. * Unavailable from part of IP phones. (Business hours : 9:00 a.m. to 8:00 p.m.) ■ From DOCOMO mobile phones (In Japanese only) (No prefix) 151 (toll free) * Unavailable from land-line phones, etc. ■ From land-line phones (In Japanese only) Repairs ■ From DOCOMO mobile phones (In Japanese only) (No prefix) 113 (toll free) * Unavailable from land-line phones, etc.
Manual for PC Connection Data Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Flow of setup for data transfer (OBEX communication) . . . . . . . . . . . . 4 Flow of setup for data communication . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Connecting up PC to the FOMA terminal . . . . . . . . . . . . . . . . . . . . . . . . .
Data Communication There are 3 communication modes available by connecting FOMA terminal and a PC : data transfer (OBEX communication), packet communication and 64K data communication. ･ To make packet communications or 64K data communications or edit data such as the phonebook using a PC connected, downloading the software from NTT DOCOMO website, installation and various settings are required.
❖ 64K data communication You can connect to the Internet and perform 64K data communication. Communication charges are based on the duration of the connection to the network regardless of the volume of data. Access points that support FOMA 64K data communication services such as mopera U of DOCOMO's Internet connection service or ISDN synchronized 64K access points can be used. Please be careful that a high cost will be charged for long-time communications.
◆ Usage precautions ❖ Internet service provider usage charges When using the Internet on a PC, usage charge to your Internet service provider (hereinafter referred to as Provider) is required. This charge is paid directly to the Provider, and is separated from the FOMA service charge. For details, contact your Provider. ･ DOCOMO's Internet connection service mopera U is available. mopera U is a charged service requiring subscription. ❖ Dialup connection (Provider etc.
Flow of setup for data transfer (OBEX communication) When using USB Cable, install FOMA communication configuration file (driver) in advance. Downloading FOMA communication configuration file (driver) from NTT DOCOMO website and installing Data transfer Flow of setup for data communication This section describes the setup work for performing packet communication or 64K data communication.
Wi-Fi connection (packet communication only) Setting the FOMA terminal to the AP mode For AP mode, see “Instruction manual (detail version) (In Japanese only)” (PDF file) of the FOMA terminal. Setting the connection→P25 Performing communication ◆ Precautions for installation/uninstallation ･ Before starting operation, make sure that no other program is running and exit the program if any. * Exit any resident programs on Windows including antivirus software.
◆ Inserting USB cable 1 Insert the connector of the USB cable with engraved side up into FOMA terminal's external connection jack horizontally. 2 Insert the other end of the USB cable connector into the PC USB port. ･ When a PC and FOMA terminal are connected, appears on the stand-by display of FOMA terminal. ❖ Removing USB cable 1 Press the USB cable's release buttons on both sides of the connector and remove the connector from FOMA terminal horizontally. 2 Remove the USB cable out from the PC.
◆ Confirming FOMA communication configuration file (driver) ･ When a PC does not detect FOMA terminal correctly, settings and communication cannot be performed. Checking on Windows 7 1 (Start)→"コントロールパネル (Control panel)"→"システムとセキュリティ (System and security)"→"デバイスマネージャー (Device manager)" in the "シ ステム (System)" category. Under Windows Vista Click (Start)→"コントロールパネル (Control panel)"→"システムとメンテナンス (System and maintenance)"→"デバイスマネージャ (Device manager)".
✔INFORMATION ･ When "FOMA F01E USB Driver" is not displayed on the deletion screen, execute the operations in "Installing FOMA communication configuration file (driver)" again and uninstall.→P6 Preparing for Bluetooth connection You can make data communication by connecting a PC compatible with Bluetooth and FOMA terminal using Bluetooth. ･ For operations of a PC, refer to the instructions manual of the PC you use.
◆ Checking modem Confirm the name of modem used on a PC or COM port number set for dialup connection. ･ When a PC does not detect FOMA terminal correctly, settings and communication cannot be performed. Checking on Windows 7 1 Click (Start)→"コントロールパネル (Control panel)"→"システムとセキュリ ティ (System and security)"→"デバイスマネージャー (Device manager)" in the "システム (System)" category. Under Windows Vista Click (Start)→"コントロールパネル (Control panel)"→"システムとメンテナンス (System and maintenance)"→"デバイスマネージャ (Device manager)".
✔INFORMATION Using pay-as-you-go data communication ･ Note that communications of large-size data such as viewing websites containing images using packet communication and downloading (example: applications, music/video data, update data of OS or anti-virus software) will require high charges. Note that FOMA flat-rate packet services such as Pake-hodai and Pake-hodai full are not applied to the data communication by connecting the FOMA terminal to a PC or another device with a USB cable.
❖ Using connection software except for DOCOMO Connection Manager DOCOMO Connection Manager includes same function as that of software below and using together is not required. Perform to change setting not to be activated or uninstall as required. ･ mopera U start up tool ･ mopera U connection & setting tool ･ FOMA PC configuration software ･ FOMA Byte counter To use docomo Wi-Fi by DOCOMO Connection Manager, uninstall the following public wireless LAN connection software.
7 Confirm "注意事項 (Precautions)" and click "次へ (Next)". 8 Confirm the contents of ソフトウェア使用許諾契約 (Software license agreement) and if you agree to the agreement, select "使用許諾契約の条項に 同意します (Agree to the clauses of the agreement)" and click "次へ (Next)". 9 Confirm the installing folder and click "次へ (Next)". ･ To change the installation destination, click "変更 (Change)" and specify any installation destination.
10 Click "インストール (Install)". 11 When the "InstallShieldウィザードを完了しました (InstallShield wizard is completed)" screen appears, click "完了 (Done)". Installation starts. Installing DOCOMO Connection Manager is completed. ✔INFORMATION ･ Installation may take a few minutes. ･ When a message notifying you to reboot Windows is displayed, follow the instruction of screen and reboot. ･ Do not install during data communication.
◆ Starting DOCOMO Connection Manager ･ Before operating, make sure that a PC and FOMA terminal are properly connected. Setting under Windows 7, Windows Vista 1 Click (Start)→"すべてのプログラム (All Programs)"→"NTT DOCOMO"→ "ドコモ コネクションマネージャ (DOCOMO Connection Manager)"→"ドコモ コネクションマネージャ (DOCOMO Connection Manager)". Under Windows XP Click "スタート (Start)"→Select "すべてのプログラム (All programs)"→"NTT DOCOMO"→"ドコモ コネクションマネージャ (DOCOMO Connection Manager)" and click "ドコモ コネクションマネージャ (DOCOMO Connection Manager)".
Setting communications without using DOCOMO Connection Manager The method of dialup connection setup without DOCOMO Connection Manager is explained. ◆ Flow of dialup network setting ･ Flow of setup for data communication→P4 ･ Before operating, make sure that a PC and FOMA terminal are properly connected. Setting the dialup connection (APN)*→P15 ・When the access point is mopera U, you do not need to set. Setting Show/Hide caller ID*→P17 ・Set as required.
❖ Setting the dialup connection (APN) Setting under Windows XP 1 Click "スタート (Start)"→Select "すべてのプログラム (All programs)"→"アク セサリ (Accessories)"→"通信 (Communication)" and click "ハイパーターミナ ル (Hyper terminal)". 2 Enter the desired dialup connection name in "名前 (Name)"→Click "OK". ･ The following characters (one-byte) cannot be used in "名前 (Name)". ￥/:＊?<>｜" 3 Enter a fictional phone number (such as "0") for "電話番号 (Phone number)" →Select "接続方法 (Connection method)"→Click "OK".
6 Confirm that "OK" is displayed and click "ファイル (File)"→Click "ハイパー ターミナルの終了 (End HyperTerminal)". 7 When confirming disconnection, click "はい (Yes)"→When confirming saving, click "いいえ (No)". ◆ Setting Show/Hide caller ID You can set to show/hide call ID for packet communication at once. Caller ID is your important information. Take care when deciding to disclose your caller ID. ･ If "Not notify" is set when using mopera U, connection is unavailable.
◆ Setting dialup network In this manual, the description takes the case of IP connection to mopera U via packet communication for example. ･ When connecting to mopera U via packet communication, enter the following number in the phone number field. mopera U (PPP connection) : ＊99＊＊＊1# mopera U (IP connection) : ＊99＊＊＊3# 128K communication (PPP connection) : ＊99＊＊＊4# ･ When connecting to mopera U via 64K data communication, enter the following number in the phone number field to connect to.
4 Enter the phone number of the dialup connection in "ダイヤルアップの電話番 号 (Dialup phone number)" ("＊99＊＊＊#" for packet communication) with one-byte→Enter "ユーザー名 (User name)"→Enter "パスワード (Password)"→Enter "接続名 (Connection name)" and click "接続 (Connect)". : The number registered in P16 "Setting the dialup connection (APN)" ･ In "ユーザー名 (User name)" and "パスワード (Password)", enter the user name and password specified by your provider or network administrator.
9 Confirm the setting of each item in "全般 (General)" tab. ･ When multiple modems are connected to a PC, set as follows. For USB cable connection : Select only "モデムFOMA F01E (Modem-FOMA F01E)" at "接続の方 法 (Connection method)" field. For Bluetooth connection : Select "モデム- (ご使用 のBluetoothリンク経由標準モデム) (Modem(Standard modem via Bluetooth link you use))" or "モデム- (Bluetooth機器メーカーが提供して いるBluetoothモデム) (Modem- (Bluetooth modem provided by Bluetooth device manufacturer))" at "接続の方法 (Connection method)" field.
❖ Setting for Windows XP 1 Click "スタート (Start)"→Select "すべてのプログラム (All programs)"→"アク セサリ (Accessories)"→"通信 (Communication)" and click "新しい接続ウィ ザード (New connection wizard)". 2 On the "新しい接続ウィザードの開始 (Start new connection wizard start)" screen, click "次へ (Next)". 3 Select "インターネットに接続する (Connect to Internet)" and click "次へ (Next)". 4 Select "接続を手動でセットアップする (Set up connection manually)" and click "次へ (Next)". 5 Select "ダイヤルアップモデムを使用して接続する (Use dialup modem to connect)" and click "次へ (Next)".
8 Enter "ユーザー名 (User name)"→Enter "パスワード (Password)"→Enter "パス ワードの確認入力 (Password confirmation entry)"→Select all items as shown below and click "次へ (Next)". ･ In "ユーザー名 (User name)" and "パスワード (Password)", enter the user name and password specified by your provider or network administrator. ･ When the access point is mopera U, you do not need to enter "ユーザー名 (User name)", "パス ワード (Password)" or "パスワードの確認入力 (Password confirmation entry)".
13 Click "ネットワーク (Network)" tab→Set each item as shown below→Click " 設定 (Settings)". ･ When settings of IP and DNS information have been requested from the provider, etc. select "イ ンターネットプロトコル (TCP/IP) (Internet protocol (TCP/IP))", click "プロパティ (Property)" and set necessary information. ･ Since "QoSパケットスケジューラ (QoS packet scheduler)" settings in "この接続は次の項目を使用 します (Use these items for this connection)" can not be changed, leave it as it is. 14 Uncheck all items ( 15 Click "OK". ) and click "OK".
4 Enter "ユーザー名 (User name)"→Enter "パスワード (Password)"→Click "ダイ ヤル (Dial)". ･ In "ユーザー名 (User name)" and "パスワード (Password)", enter the user name and password specified by your provider or network administrator. ･ When using mopera U, you do not need to enter "ユーザー名 (User name)" or "パスワード (Password)". ･ When "ユーザー名 (User name)" was entered or " パスワード (Password)" was saved while settings, these entries are no longer necessary. ･ Click "OK" when the connection established screen is displayed.
Connecting to a Wi-Fi compatible PC Even out of public wireless LAN area, you can perform packet communication with connecting a Wi-Fi compatible PC to use FOMA terminal as an access point. ･ Switch FOMA terminal to AP mode ON in advance. For AP mode settings, refer to "Instruction manual (detailed version) (in Japanese only)" (PDF file) of the FOMA terminal.
AT command AT commands are commands for setting FOMA terminal functions using a PC. FOMA terminals comply with AT commands and support some extended commands and proprietary AT commands. ❖ AT command input format "AT" must be entered before each AT command. Commands must be entered in one-byte alphanumeric characters. Connecting to mopera U with ATD command ATD＊99＊＊＊3# Return character : Press Enter key.
◆ List of AT command ･ The followings are AT command that can be used via the FOMA F01E (Modem). ･ Entering "￥" may cause "\" to appear depending on the font setting for a PC or communication software. ･ If the battery pack is removed from FOMA terminal before the terminal power is turned off, the setting values may not be recorded.
Upper slot : Command Lower slot : Example ATS4= ATS4=10 OK ATS5= ATS5=8 OK ATS6= ATS6=5 OK ATS8= ATS8=3 OK ATS10=*1 ATS10=1 OK ATS30= ATS30=0 OK ATS103= ATS103=1 OK ATS104= ATS104=1 OK ATV*1 ATV1 OK ATX*1 ATX4 OK ATZ*3 Description Set the line feed (LF) character. When result code is displayed as alphabetic characters, appends the character after the carriage return (CR) character. n=10 (fixed value) ATS4? : Display current settings Set the back space (BS) character.
Upper slot : Command Lower slot : Example AT&E*1 AT&E1 OK AT&F AT&F OK (When in offline mode) AT&S*1 AT&S0 OK AT&W Description Set the speed display used when connection is made. n=0 : Display communication speed of wireless zone n=1 : Display communication speed between a PC and FOMA terminal (default) Reset the current setting to the default. When this command is executed during communication, the terminal is reset after the line is disconnected (displaying "NO CARRIER").
Upper slot : Command Lower slot : Example AT+CBST=,1,0*1 AT+CBST=116,1,0 OK AT+CDIP=*1 AT+CDIP=0 OK AT+CEER AT+CEER +CEER : 36 OK AT+CGDCONT*2 Description Set the line to use (Setting of bearer service) n=116 : 64K data communication (default) n=134 : 64K videophone AT+CBST? : Display current settings AT+CBST=? : Display a list of assignable values Set to notify/not to notify the sub address when receiving in packet communication or 64 data communication.
Upper slot : Command Lower slot : Example AT+CNUM AT+CNUM +CNUM : ,"090XXXXXXXX", 129 OK AT+COPS=,2, *2 AT+COPS=0 OK AT+CPAS AT+CPAS +CPAS : 0 OK AT+CPIN="", "" AT+CPIN="0000" OK AT+CR=*1 AT+CR=0 OK AT+CRC=*1 AT+CRC=0 OK AT+CREG=*1 AT+CREG=0 OK AT+CUSD=,""*1 AT+CUSD=0,"012345678" OK AT+FCLASS=*1 AT+FCLASS=0 OK AT+GCAP AT+GCAP +GCAP : +CGSM,+FCLASS, +W OK Description Display FOMA terminal's own phone number in the "+CNUM : ,""," format.
Upper slot : Command Lower slot : Example AT+GMI Description Display FOMA terminal manufacturer name. AT+GMI FUJITSU OK AT+GMM Display model name of FOMA terminal. AT+GMM FOMA F01E OK AT+GMR Display FOMA terminal version. AT+GMR Ver1.00 OK AT+IFC=*1 AT+IFC=2,2 OK Set how to control local flow between a PC and FOMA terminal.
■ 64K data communication Value Description 1 Specified number does not exist. 16 Normal disconnection. 17 Communication is impossible because remote device is busy. 18 You made a call but did not receive a response within the specified time. 19 The remote device is called but no response. 21 The remote device rejected incoming calls. 63 The service and option of the network are not valid. 65 Unavailable processing speed was specified.
■ Command name : +CGEQMIN=[parameter] ･ Outline ･ ･ ･ ･ Set the criteria for judging whether to permit QoS (Quality of Service) provisioned by the network when packet communication is established.
◆ Result codes ･ When ATV command is set to n=1 (default), the result code is displayed in alphabetic characters. When the command is set to n=0, the result code is displayed numerically.→P28 ■ Result codes No.
■ Display example of result code When ATX0 is set Regardless of the settings of AT￥V command, only "CONNECT" is displayed upon completion of connection. Text display example : ATD＊99＊＊＊1# CONNECT Number display example : ATD＊99＊＊＊1# 1 When ATX1 is set ･ When ATX1, AT￥V0 (default) is set Upon completion of connection, the result code is displayed in the following format : "CONNECT ".
Kuten Code List For entering characters using code, see "Entering characters using code" in the attached manual. Note that some characters in the code input list may look different from actual ones.
1st -3rd 261 262 263 264 265 266 267 268 269 270 271 272 273 0 1 2 叉 鎖 塞 采 際 榊 搾 笹 察 鯖 捌 惨 撒 讃 賛 唆 裟 妻 犀 剤 肴 昨 匙 拶 錆 散 酸 佐 詐 哉 災 載 堺 咋 鮭 4th digit of code 3 4 5 6 7 さ 嵯 坐 宰 砕 在 咲 朔 冊 撮 鮫 桟 餐 左 座 彩 砦 材 崎 柵 刷 擦 皿 燦 斬 沙 催 栽 細 冴 鷺 索 8 9 瑳 再 歳 菜 坂 作 錯 些 砂 最 済 裁 阪 削 桜 差 挫 才 祭 罪 埼 窄 査 債 採 斎 財 碕 策 札 晒 珊 暫 殺 薩 雑 皐 三 傘 参 山 産 算 纂 蚕 残 し 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314
1st -3rd 447 447 448 449 449 450 451 452 452 453 454 455 456 4th digit of code 0 1 2 3 4 5 6 7 紋 門 匁 や 也 冶 夜 爺 耶 矢 厄 役 約 薬 訳 躍 靖 鑓 ゆ 愉 愈 油 癒 諭 輸 唯 佑 優 勇 友 悠 憂 揖 有 柚 湧 涌 猶 祐 裕 誘 遊 邑 郵 雄 融 よ 余 揚 窯 養 与 揺 羊 慾 誉 擁 耀 抑 輿 曜 葉 欲 預 楊 蓉 沃 傭 様 要 浴 8 9 野 弥 柳 薮 宥 幽 猷 由 夕 予 幼 妖 容 庸 洋 溶 熔 用 謡 踊 遥 陽 翌 翼 淀 ら 456 457 458 羅 雷 洛 絡 落 酪 藍 蘭 覧 螺 裸 来 莱 頼 乱 卵 嵐 欄 濫 り 458 459 460 461 462 463 464 465 履 李 痢 葎 掠 隆 竜 両 凌 糧 良 厘 林 466 瑠 塁 涙 累 類 利 吏 梨 裏 略 龍 寮 諒 淋 理 裡 劉 侶 料 遼 燐 璃 里 流 慮 梁 量 琳 離 溜 旅 涼 陵 臨 陸 琉 虜 猟 領 輪 律
1st -3rd 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 696 697 698 699 700 701 702 703 704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 0 瞽 砌 碚 碾 礫 禊 秕 稟 穢 窖 竊 竦 笞 筧 箚 箴 簇 簟 籘 粭 粽 糲 紵 經 緇 緘 縡 縵 繙 辮 纎 罟 羇 羮 翦 耙 聚 聿 胛 脛 腦 膣 臂 臠 舍 艝 艷 苣 苞 茯 茣 莨 菷 菻 蒂 蒿 蒡 蓼 薨 藉 蘊 虍 蚋 蛔 蜀 蜷 蝴 螽 蟯 1 瞻 砒 碌 碼 磧 祀 禝 秧 禀 穩 窩 竍 竭 笵 筺 筰 箋 篆 簓 簷 籟 粢 糀 糴 紂 絆
