INSTRUCTION MANUAL ’ 12.
Introduction Thank you for your purchase of "SO-01E". For proper use of the SO-01E, read this manual carefully before and while you use the SO-01E. About manuals of SO-01E In addition to this manual, the operations of SO-01E are described in " クイックスタートガイド (Quick Start Guide)" (in Japanese only) and "Instruction Manual" application of the terminal (in Japanese only).
Operation descriptions In this manual, each key operation is described with p, x, y, r, m. And selection operations of the icons or function items on the touch screen are described as follows. Description From the Home screen, tap and tap [Settings]u[About phone]. Touch and hold an icon. Operation From the Home screen, tap (Applications button), and then tap "Settings" on the next screen and "About phone" on the following screen in order. Keep touching an icon longer (12 seconds).
Supplied accessories ･ ･ ･ Battery Pack SO08 ･ Desktop Holder SO14 (with warranty) ･ 1Seg antenna cable SO01 ･ microSD card (2GB) (Sample)* SO-01E (with warranty) Back Cover SO21 (Inserted in the terminal when purchased.
Contents ■ Supplied accessories. . . . . . . . . . . . . . . . . 2 ■ About using the terminal . . . . . . . . . . . . 5 ■ Safety Precautions (Always follow these directions) . . . . . . . . . . . . . . . . . . . . . . . . . . 7 17 24 ■ Handling precautions. . . . . . . . . . . . . . . ■ Waterproofness/Dustproofness . . . . . Before Using the Terminal . . . 30 Part names and functions................................................30 docomo mini UIM card ...................................................
Osaifu-Keitai........................................................................... 169 1Seg............................................................................................ 175 FM radio................................................................................... 183 Camera...................................................................................... 185 Playing multimedia content........................................ 203 Album.................................................
Contents/Precautions About using the terminal The terminal supports LTE, W-CDMA, GSM/ GPRS and Wireless LAN Systems. ･ Because a terminal operates using radio frequencies, it cannot be used inside a tunnel, underground, in a building or other locations where radio waves do not reach the terminal, in locations with weak radio wave condition, or out of Xi/FOMA service area.
The terminal automatically performs communication for synchronizing data, checking the latest software version, maintain connection with the server, etc. If you transmit a large amount of data such as downloading applications or watching movie, a packet communication charge becomes high. Subscription of packet flatrate service is highly recommended. ･ Depending on the applications or service you use, packet communication fees may be charged even in Wi-Fi communication.
The terminal supports only sp-mode, mopera U and Business mopera Internet. Other providers are not supported. ･ To use tethering, subscription of sp-mode is required. ･ Packet communication charge when using tethering varies depending on the charging plan you use. Subscription of packet flat-rate service is highly recommended. ･ For details on usage charge, etc., refer to the following website. http://www.nttdocomo.co.
■ The following symbols indicate specific directions. Indicates prohibited actions. Don’t 1. Handling the terminal, battery pack, adapter, desktop holder, docomo mini UIM card, 1Seg antenna cable (common) DANGER Indicates not to disassemble. No disassembly No liquids No wet hands Do Unplug ■ Indicates not to use where it could get wet. Don’t Indicates not to handle with wet hands. Indicates compulsory actions in accordance with instructions.
WARNING Don’t Don’t Don’t Do Do not subject the equipment to excessive force or throw it. Doing so may cause fire, burns, injury or electric shock. Do Do not allow the contacts for the desktop holder, the microUSB jack or headset jack to touch conducting foreign substances (a piece of metal, pencil lead, etc.). Never allow these objects to get inside. Doing so may cause fire, burns, injury or electric shock. Do not cover or wrap the equipment with a cloth or bedding in use or while charging.
Do Be careful especially when using the terminal connected to the adapter continuously for a long time. If you play a game, watch 1Seg, etc. for a long time while charging, the temperature of the terminal, battery pack and AC adapter may rise. If you are directly in contact with hot parts for a long period of time, it may cause your skin to become red, itchy, or develop a rash depending on your physical condition and also it may cause low-temperature burn. 2.
Do Do Do Always keep the terminal away from your ear when you talk setting the hands-free function. Also, when you play game, play back music, etc. connecting the Earphone/Microphone, etc. to the terminal, adjust the volume adequately. If the volume is too loud, it may cause difficulty in hearing. Moreover, if you barely hear the surrounding sounds, it may cause an accident. Do If you have a weak heart, set the vibrator or ringtone volume carefully. Failure to do so may affect your heart.
CAUTION Don’t Don’t Don’t Don’t Do Do Do not swing the terminal around by holding a strap etc. The terminal may hit you or others and cause accident such as injury. Do not use damaged terminal. Doing so may cause fire, burns, injury or electric shock. When using the motion sensor, check the safety around you, hold the terminal firmly, and do not shake it unnecessarily. May cause accident such as injuries.
Don’t Do Do not stick a nail into the terminal, hit it with a hammer, or step on it. Doing so may cause battery pack to ignite, burst, heat or leak. If the battery pack's fluid etc. contacts eyes, immediately flush the eyes with clean water and see a doctor right away. Do not rub the eyes. Failure to do so may cause blindness. Don’t Do WARNING Don’t Do Do If the battery pack seems to have abnormalities such as deformation or scratches due to falling, never use it.
Don’t Do not short-circuit the microUSB plug while it is connected to the power outlet or cigarette lighter socket. Do not touch the microUSB plug with your hands, fingers, or any part of your body. Doing so may cause fire, burns or electric shock. Don’t Do not place heavy objects on the adapter cord. Doing so may cause fire, burns or electric shock. Don’t When you insert and remove the AC adapter from power outlet, do not contact a metal strap or other metal objects with the jack.
5. Handling the docomo mini UIM card Do CAUTION Do Be careful of the cut surface when removing docomo mini UIM card. Failure to do so may cause injury. 6. Handling the terminal near electronic medical equipment ■ Do The following instructions observe the guidelines of the Electromagnetic Compatibility Conference, Japan to protect electronic medical equipment from radio waves from mobile phones. WARNING Do Please observe the following guidelines in medical facilities.
7.
Part Desktop holder (contacts) Desktop holder (label) Desktop holder (rubber foot) Desktop holder (screws) 1Seg antenna cable (headset jack : upper surface) 1Seg antenna cable (headset jack : ring) 1Seg antenna cable (headset jack : body) 1Seg antenna cable (cable) 1Seg antenna cable (plug : upper surface) 1Seg antenna cable (plug : ring) 1Seg antenna cable (plug : body) 1Seg antenna cable (plug : metal) Material Surface treatment Gold plating Phosphor bronze Polyester resin ― Handling precautions ■ Co
･ Clean the terminals occasionally with a dry cotton swab. If the jack is soiled, connection gets worse and it may cause power to be turned off or insufficient battery charge, so clean the jack with a dry cotton swab etc. When cleaning, be careful not to damage the terminals. ･ Do not leave the terminal near the air conditioning vent. Extreme temperature changes may produce condensation and corrode the internal parts of the terminal, causing it to malfunction.
･ Do not leave the camera under direct sunlight. Charge the battery pack in an environment with the proper ambient temperature (5 ℃ to 35 ℃ ). ･ The operating time of the battery pack varies depending on the operating environment and the secular degradation of the battery pack. ･ The battery pack may swell out as it comes to near the end of its lifetime depending on the usage conditions, but it is not a problem. ･ Be careful especially about the following points when preserving the battery pack.
The adapter cable could become warm while charging. This condition is not abnormal. You can continue using the terminal. ･ When using the DC adapter for charging, do not turn off the vehicle engine. ･ ･ Under no condition will DOCOMO be held liable for any damaged or lost data saved in the terminal. Take an expended docomo mini UIM card to sales outlet such as docomo Shop for proper disposal in order to protect the environment. ･ Do not carelessly damage, contact, or short-circuit an IC.
Please be aware that DOCOMO is not responsible for data leak when making data communications using Bluetooth.
･ Wireless LAN Do not use wireless LAN near magnetic devices such as electrical appliances or AV/OA devices, or in radio waves. - Magnetism or radio waves may increase noises or disable communications (especially when using a microwave oven). - When used near TV, radio, etc., reception interference may occur, or channels on the TV screen may be disturbed. - If there are multiple wireless LAN access points nearby and the same channel is used, search may not work correctly.
Channel number (Ch) 5.6GHz band 100 102 104 108 110 112 116 118 120 124 126 128 132 134 136 140 Frequency band (MHz) 5,500 5,510 5,520 5,540 5,550 5,560 5,580 5,590 5,600 5,620 5,630 5,640 5,660 5,670 5,680 5,700 ■ FeliCa reader/writer function precautions FeliCa reader/writer function of the terminal uses weak waves requiring no licenses for radio stations. ･ It uses 13.56 MHz frequency band. When using other reader/writers in your surroundings, keep the terminal away sufficiently from them.
■ Note ･ Do not use altered terminal. Using an altered device is a violation of the Radio Law. A "Technical Conformity Mark " affixed on the manufacturer's specification sticker certifies that the terminal meets technical regulations for specified radio equipment that are based on the Radio Law. If you remove the screws and alter the inside of the terminal, the technical regulations conformity certification becomes invalid.
What you can do with waterproofness/dustproofness of SO-01E You can talk without an umbrella in the rain (for rainfall of 20 mm or less per hour). - Do not open or close microUSB jack cover or headset jack cover when your hands are wet or waterdrops are attached to the terminal. ･ You can wash the terminal when it gets dirt or stained with liquid other than tap water. - Wash the terminal with tap water at normal temperature (5 ℃ -35 ℃ ) by weaker water flow (less than 6 L/min.
■ Opening the microUSB jack cover and headset jack cover Back cover Open the covers with your finger by the grooves. Groove ■ 1 Groove ■ Groove Closing the microUSB jack cover and headset jack cover Press the covers in the directions of the arrows and ensure there are no gaps. ■ 1 Attaching back cover Check the orientation of the back cover, and attach it to the terminal ( ), then press down the part firmly, and then check that there are no gaps between the terminal and back cover ( ).
It is recommended to replace the parts for maintaining waterproof/dustproof property once every two years regardless of whether any abnormality is present. DOCOMO replaces the parts as a chargeable service. Bring the terminal to a sales outlet such as a DOCOMO-specified repair office. Important precautions Do not perform actions shown in the illustrations below.
If the terminal gets splashed with water or other liquid while microUSB jack cover, headset jack cover or back cover is opened, the liquid may get inside the terminal causing electric shocks or malfunction. Stop using the terminal, turn off the power and contact a DOCOMO-specified repair office. ･ If the microUSB jack cover, headset cover, the rubber gasket of the inner side of the back cover is damaged or deformed, have it replaced at DOCOMO-specified repair office.
c d Swing the terminal in about 10 times against dry, clean cloth etc. to wipe off water remaining in the microphone, earpiece, speaker, power key, volume key, contacts for the desktop holder, each cover (microUSB jack cover/headset jack cover), etc. Wipe off water drained from the terminal with dry, clean cloth etc., and dry naturally. ･ Wipe off water drained from the terminal with dry, clean cloth etc., and dry naturally. ･ Do not wipe off water remaining in gaps directly with a cotton swab etc.
Part names and functions a b cde h i j w l f k m n g Front camera lens Ear speaker Infrared data port Light sensor : Use for auto controlling of the screen brightness. e Notification LED f Proximity sensor : Turns on or off the touch screen to prevent misoperation during a call. g Touch screen h GPS antenna section* i Camera lens j Second microphone : Reduce noise to make easy to listen.
❖Note Do not put stickers etc. on each sensors. Do not peel off the silver sticker on the inner side of the back cover. Removal of the sticker may disable reading/writing of IC card. ･ Do not peel off the round mesh sheet on the inner side of the back cover. Doing so makes waterproof ineffective. ･ ･ docomo mini UIM card The docomo mini UIM card is an IC card recorded user information such as your phone number etc. ･ You can use the terminal with docomo mini UIM card.
Inserting docomo mini UIM card 1 2 Insert the tip of your finger into the groove at the bottom of the terminal, and lift up the back cover (P.26). Remove the battery pack and microSD card, place the tip of your finger on the projection ( ) at the edge of the tray, and pull out the tray straight, then insert your docomo mini UIM card into the tray, with the metal (IC) part facing down, and then press the tray with the docomo mini UIM card straight to the end.
microSD card microSD card You can use microSD card for any other compatible devices. ･ The terminal supports microSD card of up to 2GB, and microSDHC card of up to 32GB (As of October, 2012). ･ For compatible microSD cards, contact manufacturers of microSD cards. ･ When inserting/removing a microSD card, make sure to power off the terminal. Do not connect the AC adapter. Inserting microSD card 1 Insert the tip of your finger into the groove at the bottom of the terminal, and lift up the back cover (P.
Removing battery pack Battery pack ･ When attaching/removing the battery pack, make sure to power off the terminal. Do not connect the AC adapter. 1 Attaching battery pack 1 Insert the tip of your finger into the groove at the bottom of the terminal, and lift up the back cover (P.26). 2 Check the position of charging contacts of the battery back, and align the tabs of the terminal with those of the battery pack, then insert it in the direction of the arrow ( ).
Battery pack life Charging The battery pack is not full charged when you purchased the terminal. Charging time The following is the time for charging an empty battery pack. Charging under low temperature requires longer time. AC Adapter 03 (Optional) DC Adapter 03 (Optional) Approx. 160 min. (approx. 170 min. with Desktop Holder SO14) Approx. 180 min. Operation time on full charge (estimate) The following time varies by the battery pack condition or operating environment. For details, see (P.254).
When you start charging, notification LED on the terminal turns red/orange/green, and green light indicates that the battery level has reached 90 % or more. To check the status of charging, from the Home screen, tap and tap [Settings]u[About phone]u[Status] to see "Battery level". When charging is complete, battery level is displayed as "100%" at the status bar or "Battery level", and "Charged." appears on the unlock screen.
❖Note You cannot charge the battery by connecting the desktop holder to a PC. ･ If you connect the microUSB cable to the USB jack of the desktop holder for charging, the terminal is powered on and notification LED lights although the operations are not available. Be careful not to connect with the microUSB cable in a place where the use is prohibited such as in a airplane or hospital. ･ Check the connecting direction to connect correctly. Wrong connection may cause damage.
❖Note If you connect the microUSB cable to the USB jack of the terminal for charging, the terminal is powered on and notification LED lights although the operations are not available. Be careful not to connect the microUSB cable in a place where the use is prohibited such as in a airplane or hospital. ･ 2 Notification LED lights on the terminal. For the notification LED for charging, see "Notification LED" (P.44). ･ When "PC Companion software" screen appears on the terminal, tap [Skip].
Turning power on/off Notification LED Turning power on 1 Press and hold p for over a second. ･ The unlock screen appears. microUSB plug AC adapter USB plug microUSB cable USB plug 2 Unlock the screen. ･ For unlocking the screen by default, see "Unlocking the screen" (P.40). ❖Information The first time you turn on, the initial setting screen appears (P.40). ･ If you have activated the screen lock (P.146) or SIM card lock (P.146), unlock screen/PIN code entry screen appears when turning power on.
Turning power off 1 Press and hold p for over a second. 2 3 Tap [Power off]. Tap [OK]. When the screen lock is set, the screen backlight turns off. You can avoid the touch screen or key from false operations. ･ The screen is locked with turning the screen backlight off after the specified time duration. Press p. ❖Information Screen lock is set by default. For changing the screen lock, see "Changing screen unlock method" (P.147).
2 Tap when initial setting screen for docomo service appears. ･ 3 After this step, follow the onscreen instructions to set up below, and tap . - Select whether to install all apps now or later - Select whether to set Osaifu-Keitai settings - Set docomo apps password settings - Set whether to respond when receive a request of location search A status bar appears at the top of the screen. In the status bar, the terminal status and notification are displayed.
Bluetooth function ON Connecting to Bluetooth device Airplane mode activated Silent mode (vibration) ON Silent mode (mute) ON Speakerphone ON Microphone set to mute Alarm is set Reader/Writer, P2P function ON Battery status The battery is charging PUK code locked or docomo mini UIM card not inserted Notification icon The main notification icons displayed on the screen are as follows.
1Seg activated FM radio in use USB connected MHL connected Available to activate TV launcher Screen mirroring connected Communicating via Infrared Data communication invalid Wi-Fi open network available Connecting to a VPN The terminal set as media server/Connection request notification received Error message Warning message Problem with sync Setup guide unchecked Notification such as personal area received More (undisplayed) notifications Wi-Fi tethering set/Wi-Fi Direct connected Setting USB tethering Set
❖Information Drag the status bar downwards to enable/disable silent mode or data communications. ･ ／ / / ／ / / ／ ／ ／ ／ Enable/disable Wi-Fi function. Enable/disable Bluetooth function. Enable/disable data communication. Switch screen brightness. Enable/disable silent mode (Vibrate/Mute). Enable/disable Wi-Fi tethering function. Enable/disable GPS function. Enable/disable Airplane mode. You can set whether to switch portrait/landscape view automatically according to the terminal orientation.
Basic operations Basic key icon operation x y r x Back y Home Small Apps r Go back to the previous screen. Or close a dialog box, an option menu, the Notification panel or a software keyboard. Go to the Home screen. Display recently used applications in thumbnail list, activate or delete from the list. Also, use or set small apps (P.83). * In this manual, each key icon operation is described with x, y, r.
■ Scroll When whole content cannot be displayed, flick up/down/left/right displayed content to scroll (move) the display position. Switching portrait/landscape view automatically You can set the screen orientation to switch between landscape and portrait view automatically according to the terminal orientation. 1 2 ■ Drag the status bar downwards. Tap (gray). ･ The setting is enabled. Tap disable.
Capturing screenshot You can save the current displayed screen as an image (screen shot). You can check captured screen shots on the album (P.205). 1 On the screen you want to capture, press and hold p and lower of m for over a second at the same time. ･ Screenshot is captured and in the status bar. When a checkbox/radio button is displayed besides a setting item, mark or unmark a checkbox/radio button to switch on/off for the setting.
Searching information in the terminal and web pages Enter a word in the search box to browse the information in the terminal or on the Internet. 1 From the Home screen, tap then tap [Search]. ･ 2 3 , The software keyboard appears. Enter a search word. Search suggestions appear as you enter a character. For character entry, see "Character entry" (P.49). ･ To enter a new search word, tap . ･ Tap at the right end of search item to enter a selected item and search again. ･ Tap a search item or ･ .
Change the search range by marking/unmarking data categories (Google, Apps, Browser, Chrome, Contacts, docomo phonebook, Email, File Commander, Messaging, OfficeSuite, Play Movies & TV, WALKMAN) in the terminal. Google Search Set whether to display search options from Web history when a search word is entered, or delete a search history for contents or applications in the terminal. ･ You need to create your Google account.
1 From the Home screen, tap then tap [Settings]. 2 Tap [Language & input]u[Default]u[Xperia™ Chinese keyboard]/[Xperia™ Japanese keyboard]/[Xperia™ keyboard]. , ■ Phonepad keyboard Portrait ❖Information While entering characters, drag the status bar downwards and tap [Select input method] to select from "Google voice typing"/"Moji-Henshu"/"Xperia™ Chinese keyboard"/"Xperia™ Japanese keyboard"/ "Xperia™ keyboard".
■ Japanese syllabary keyboard Changing keyboard or settings 1 On a character entry screen, touch and hold . 2 Tap / / / / / : The phonepad keyboard appears. : The QWERTY keyboard appears. : The Japanese syllabary keyboard appears. ･ : The Kana handwriting input appears. ･ Tap to display Japanese keyboard settings screen and you can check/ change the settings. ･ Tap to display the extensions list. ･ : Switch one-byte/two-byte character. ･ : Hide the software keyboard.
Entering characters on the phonepad keyboard Enter characters using a keyboard with characters allocated in the same arrangement as general cell phones. Flick input or toggle input is used for character entry. Icon / Function Each time you tap, the character mode switches "Hiragana/Kanji" → "Alphanumeric" in order and a status → / / appears in the icon, status bar. / Display a pop-up window.
Icon Function Display the available extensions list. Touch and hold Display the previous character (opposite order). In Hiragana/Kanji input mode, highlight and select word in conversion candidates. Tap continuously to change a word highlighted in conversion candidates and select a word to enter. Activate online dictionary. Touch and You need to mark "Online dictionary" hold checkbox in the Japanese keyboard setting screen. / Appears when entering numbers, tap to switch one-byte/two-byte character.
c [On-screen keyboard settings]uUnmark "Flick input" ･ ■ checkbox. To change sensitivity of the flick input, on a character entry screen, touch and hold , tap and [On-screen keyboard settings]u[Sensitivity of flick input], then select "High"/"Medium (default)"/"Low". c [On-screen keyboard settings]uUnmark "Multitap text input" checkbox.
Entering characters on the QWERTY keyboard Icon Enter characters using a keyboard with characters allocated in the same arrangement as general PCs. Enter Japanese in Roman character. Icon / Function Each time you tap, the character mode switches "Hiragana/Kanji" → "Alphanumeric" in order and a status → / / / / / icon, appears in the status bar. / Display a pop-up window.
Icon Function / / In alphanumerics input mode, tap to switch capitalization/upper case/lower case. In Hiragana/Kanji input mode, highlight and select word in conversion candidates. Tap continuously to change a word highlighted in conversion candidates and select a word to enter. Activate online dictionary. Touch and You need to mark "Online dictionary" hold checkbox in the Japanese keyboard setting screen. / Appears in number input mode. Tap to switch numbers or symbols to one-byte/ two-byte characters.
■ ■ Key highlight while typing Changing display keys Widen frequent using key and highlight the key that is predicted for the next entry. You can set not to display less-frequent-used keys (Q, X, C, etc.) on the QWERTY keyboard. Dynamic key resizing with highlight 1 On a character entry screen, touch and hold . 2 3 Tap . Tap [On-screen keyboard settings]u[Hide keys]. ･ Widen the key that is predicted for the next entry much further and highlight it. ■ When the Choose key type (P.
Customizing keyboard ❖Information You can change symbols which are displayed in QWERTY keyboard when entering number to desired characters/symbols. ･ 1 On a character entry screen, touch and hold . 2 3 Tap . Tap [On-screen keyboard settings]u[Keyboard customization]. 4 Tap a symbol you want to change and delete character previously set, then enter a character to display and tap [OK]. ･ 5 Only one character (two-byte or onebyte character) can be entered. Tap [OK].
Icon Function / Enter one-byte/two-byte symbols from Touch and the displayed list. Switch the tab to enter hold facemarks from the displayed list (a pictogram tab and deco-mail tab are also displayed when entering in spmode mail). Move the cursor*1 : To the left. Touch and hold to move continuously. Or change the range for conversion. Move the cursor*1 : To the right. Touch and hold to move continuously. Or change the range for conversion.
Entering characters on the Kana handwriting input Enter characters by tracing characters on the Kana handwriting area. Icon / Function Each time you tap, the character mode switches "Hiragana/Kanji" → "Alphanumeric" in order and a status → / / appears in the icon, status bar. / Display a pop-up window.
Icon Function When any character is entered or after entered character is fixed, a space can be entered. Touch and hold to input spaces continuously. Enter characters by voice input with "docomo voice input" or "Google voice typing". A candidate list appears. Tap the character string you want to enter. Kana handwriting input guide in the Touch and POBox Touch User Guide (Japanese) hold activates and you can view the detailed explanations on the Kana handwriting input.
❖Information Setting Xperia™ Japanese keyboard To paste a copied or cut character string, touch and hold a position where you want to insert, then tap [PASTE]. Alternatively, when texts are entered, tap a position where you want to insert, then tap and [PASTE]. ･ Edit menu icons vary by applications. ･ Setting character entry Displaying the setting screen for Xperia™ Japanese keyboard 1 From the Home screen, tap , then tap [Settings]u[Language & input]. 2 Tap on "Xperia™ Japanese keyboard".
Sound on keypress Vibration on keypress Pop-up on keypress No. of lines (portrait) No. of lines (landscape) Set whether to sound at the time of key tapping. Set whether to vibrate at the time of key tapping. Set to pop up the key you have tapped at the time of key tapping. Set number of lines for conversion candidates displayed in portrait mode. Set number of lines for conversion candidates displayed in landscape mode. Setting voice input Set voice input to "docomo voice input" or "Google voice typing".
Setting keyboard skin Setting Word suggestion You can change software keyboard skin. 1 1 On the setting screen for Xperia™ Japanese keyboard, tap [Keyboard skin]. 2 Select from displayed keyboards and tap [Set skin]. ❖Information To download and add keyboard skins from a website, tap [Search for skin] in Step 2. Some keyboard skins downloaded from website may not support the terminal.
Setting Auto space ❖Information When selecting English word suggestion, Auto space enters next to the entered character. However, space is not entered automatically in the mail address or URL input fields. ･ 1 On the setting screen for Xperia™ Japanese keyboard, mark "Auto space". User dictionary settings To display the word as the preferred candidate when entering characters, set the user dictionary beforehand.
Setting online dictionary 4 Tap [Go]. 5 Tap [OK]u[OK]. In Hiragana/Kanji input mode, touch and hold to activate online dictionary. 1 On the setting screen for Xperia™ Japanese keyboard, tap [Online dictionary]. 2 Tap [Online dictionary], then read the note and tap [Agree]. ･ "Online dictionary" is marked. Backing up and restoring dictionary User dictionary and Words by learning can be backed up onto an internal storage and restored when needed.
Using extensions You can use or add extensions when entering characters. Using Contact Picker 2.3 If contacts are registered to the Contacts, you can use "Contact Picker 2.3" to enter contact information when entering characters. 1 On a character entry screen, touch and hold . 2 3 Tap . Tap [Contact Picker 2.3]u"Contacts" tab. Tap the contact to pick up. 4 5 ･ When you enter a name or reading in the search box at the top of the screen, a list of contacts appears accordingly.
POBox Touch User Guide You can view the detailed explanations on the high performance Xperia™ Japanese keyboard from the basic to application. The latest information can be obtained from the websites for extensions or keyboard skins. 1 On the setting screen for Xperia™ Japanese keyboard, tap [POBox Touch User Guide]. ･ POBox Touch User Guide appears.
- Press "Ctrl" key and "C" key to copy a selected character string. - Press "Ctrl" key and "V" key to paste a copied or cut character string. ･ While displaying word suggestions, press "Shift" key/ "Alt" key on the USB keyboard or the Bluetooth keyboard to activate Online dictionary. You need to mark "Online dictionary" checkbox in the Japanese keyboard setting screen beforehand.
❖Information docomo Palette UI Home screen Learning Home screen Tapping y displays Home screen which consists of up to 12 screens you can use flicking left and right. a b c d e g f e a b c d e f g You can switch the home application between "docomo" and "Xperia™" in the terminal. "docomo" is set to the home application by default.
Displaying a list of home screens 1 From the Home screen, pinch-in. ･ A home screen list appears. ❖Information Touch an hold an area of the Home screen where no icons are displayed and tap [Home screens] to display list of home screens. ･ When the instruction guide for the home screen list appears, tap [OK]/[Do not show this again]. ･ To return to the home screen, pinch-out, or tap y or x. ･ Adding to the Home screen 1 Touch and hold an area of the Home screen where no icons are displayed.
Adding a widget to the Home screen 1 On "Select an action" menu screen (P.71), tap [Widget]. ･ A list of widgets appears. Bookmarks Bookmarks Calendar Contact Contents Headline docomo location information docomo Wi-Fi Easy Connection Email Facebook Gmail Google Search Google+ posts IC Tag/Barcode Reader Infrared Display bookmarks of Browser. Display bookmarks of Chrome. Display the calendar. Display contacts using Contacts application of Xperia™.
スマホなるほど ツアーズ (Tips View "Tips of smartphone for docomo with series". of smartphone for docomo with series) マチキャラ (Machi-chara) 診断ツール Select an item. ❖Information ･ If you install an application with widget from Google Play, the installed widget is added to the widget list. Adding a folder to the Home screen 1 On "Select an action" menu screen (P.71), tap [Folder]. ･ ･ Alternatively, touch and hold a folder and tap [Edit name], then enter a folder name and then tap [OK].
2 Tap [Album]/[Live Wallpapers]/ [Xperia™ wallpapers]. When you tap [Xperia™ wallpapers], select an image to set to the wallpaper, tap [Set wallpaper]. ･ When you tap [Album], select an image to set to the wallpaper, drag and set trimming frame for range in the image you want to use as wallpaper, and then tap [Crop] to set wallpaper. ･ When you tap [Live Wallpapers], select a content, tap [Set wallpaper]. You can also download and add Live wallpaper content from a web page.
Sorting home screens 1 From the Home screen, pinch-in. 2 Touch and hold a home screen you want to sort. 3 Drag it to the place you want to move. ･ A home screen list appears. Moving an icon on the Home screen 1 From the Home screen, touch an icon you want to move. 2 Drag it anywhere. ･ To move to another Home screen, keep touching the icon and drag it to left or right. Deleting an icon from the Home screen 1 From the Home screen, touch and hold an icon you want to delete. 2 Tap [Delete].
d Application screen You can access the applications installed in the terminal from the Application screen and use each function. Learning Application screen 1 From the Home screen, tap (Applications button). ･ The Application screen appears. a b Group name ･ To display/hide applications in the group, tap the group name. e Application icon ･ is displayed for newly arrived application. ･ Some application icons are displayed with a number of missed calls or unread mails.
services or functions of the terminal (in Japanese only). ドコモバックアップ (docomo backup) An application for using " ケータイデータお 預かりサービス (Data Security Service)", "電 話帳バックアップ (Phonebook backup)" or "SD カードバックアップ (SD card backup)". Back up or restore phonebook data etc. For information on docomo backup (save to microSD card), see " ドコモバックアップ (docomo backup)" (P.227). docomo Wi-Fi Easy Connection An application for simply using "docomo Wi-Fi" public wireless LAN service by DOCOMO or home Wi-Fi.
Disaster kit An application which helps you to check received Early Warning "Area Mail", make settings, and record and check messages on the docomo Disaster Message Board. Instruction Manual Display the terminal instruction manual. You can start a function you want to use from the explanation (in Japanese only). * See "About manuals of SO-01E" in "Introduction". Settings Make the terminal settings.oP.
■ Xperia FM radio Use FM radio.oP.183 Music Unlimited Connect to "Music Unlimited" which allows you to listen to music around the world anytime and anywhere. PlayMemories Online Upload simply photos or videos onto the photo/video cloud service by Sony, and share uploaded photos or videos with specified friends. PSMを始めよう (Let's start PSM) Show dedicated website for the "PS Store". Download games to play on the terminal. Timescape™ View Social Networking Service (SNS) history.oP.
Contacts Activate Xperia™ phonebook application to manage contacts of your friends or colleagues. Facebook Activate Facebook client application.oP.140 OfficeSuite View and read Office documents.oP.229 File Commander You can easily find still pictures, videos, music data, downloaded files, etc. ■ Google Email Send and receive emails (multiple accounts are also available).oP.105 Gmail Send and receive mails from/to a Google account.oP.112 Messaging Send and receive messages (SMS).oP.
Messenger Chat with friends using Google+ instant messaging. ❖Information ･ ･ ･ ･ ･ ･ The applications displayed on this application screen are pre-installed by default. Some pre-installed applications can be uninstalled. Even if you uninstall, you can download in "Play Store" (P.168) again. From the Home screen, tap and tap "Recommends" tab u[ おすすめアプリを見る (See recommended applications)] to display applications recommended by DOCOMO. For details, see "Installing "Recommends" applications" (P.84).
❖Information ･ To move an application icon to another application group, touch and hold the icon on the Application screen, tap [Move], then select a desired group, or touch and hold the icon on the Application screen, then drag it to a group to move to. Uninstalling an application Some application icons can be deleted from the Application screen. ･ Before uninstalling application, back up contents related to the application that you want to save including data saved in the application.
2 Tap [Delete]u[OK]. ･ Application icons belonged to the deleted group move to the "Download Application" group. ❖Information ･ "Recently", "DOCOMO Services", and "Download Application" groups cannot be deleted. Sorting groups 1 From the Application screen, touch and hold a group name you want to sort. 2 Drag it anywhere. Changing group name ･ The group is moved. Small apps 1 From the Application screen, touch and hold a group you want to rename.
Searching applications Search application installed into the terminal to activate. 1 From the Application screen, tap and then tap [Search]. ･ 2 3 The software keyboard appears. Enter application name to search. ･ Search suggestions appear as you enter a character. Tap a search item. ･ The application activates. ❖Information When you use for the first time, a confirmation screen appears asking whether to use My location info for the Google search result or service.
Emergency call Phone Making/Receiving a call Making a call 1 2 From the Home screen, tap , then tap "Dial" tab. Enter the number of the recipient and tap . ･ 3 If a wrong number is entered, tap delete the number. to In Step 2, tap without entering a phone number to enter the phone number registered as the latest call in Recent calls (phone number for missed call is not included). ･ To activate Xperia™ phone application, from the Home screen, tap , then tap [Dial].
location information and phone number are not notified. However, the Emergency call acceptance organization may decide to obtain the location information and phone number regardless of your settings when they consider it is necessary for lifesaving, etc. Note that the areas/time for which the "Emergency call location information" is ready to be used vary depending on the preparatory state of each Emergency call acceptance organization.
Declining a call 1 While receiving a call, touch and hold (right) and drag it to (left). ❖Information During the screen lock, the icon appears and you can reject a call by the same operation. ･ If you reject an incoming call during use of Voice Mail Service, the call is connected to the Voice Mail service center. ･ Declining an incoming call and sending a message (SMS) When you cannot answer a call, you can reject the call and send a message (SMS).
■ 1 Making a call Make a call with Stereo Headset with Microphone connected. ･ 2 ■ 1 Press the switch to end the call. Receiving a call While receiving a call, press the switch of Stereo Headset with Microphone. ･ ･ 2 An operation of making a call is the same as usual operation (P.85). Calling screen On the Calling screen, you can set speakerphone or mute, or enter a phone number to make a call to another party. a b c d e f The call is connected.
g Option menu : Set Hold during a call. ･ To cancel Hold, tap [Retrieve call] during Hold. ･ To set a call on hold, "Call waiting" subscription is required (P.91). h Mute : Set muting on/off of the microphone during a call. ･ When the microphone is muted, a mute icon appears in the status bar. i Dial key : Enter the phone number you want to add to make a call. ･ The ongoing call is automatically on hold. ･ To add a call, "Call waiting" subscription is required (P.91).
Tap desired phonebook entry, or tap [Register new]. Notified if calls are made with "186" (Notify)/"184" (Hide) prefixed to the number. ･ If you enter a phone number and tap , then select [Caller ID notification]u[Notify]/[Not notify] to make a call, / does not appear in the Recent calls screen. : Koe-no-Takuhaibin ･ For details on Koe-no-Takuhaibin, refer to "Koeno-Takuhaibin" (P.91) or NTT DOCOMO website.
Network service Displaying missed calls When you have missed calls, the status bar. 1 2 appears in Drag the status bar downwards. Tap [Missed call]. ･ Recent calls screen appears. ❖Information ･ When you have missed calls, an icon appears indicating missed calls and the number of them in the screen unlock screen. Call settings 2 From the Home screen, tap then tap . Tap [Call settings].
Network Service Second call Set action for additional settings incoming call during a call. Call Notify incoming calls by notification SMS while the power is off or you are out of service area. English Switch the voice guidance guidance to English or Japanese. Remote Set to operate Voice Mail operation Service or Call settings forwarding Service using land-line phone, public phone or DOCOMO mobile phone, etc. P.
Phonebook list screen On the phonebook list screen, you can view details of your contacts. You can add a picture to a phonebook entry, and display phonebook entries by group. g h a i j i j Option menu My profile tab ･ Check your own phone number. k Index character area ･ Tap index character to display phonebook entries allocated to the index character. l Index ･ Display the index character to search entries in the order of Japanese syllabary, alphabet, etc.
❖Information ❖Information When you save "Phonetic name (family/given)", phonebook list is displayed according to Japanese syllabary order or alphabets order of "Phonetic name". If you enter "family/given" in Kanji without entering "Phonetic name" to add phonebook entry, the name appear in "ABC" field on the phonebook list screen. ･ To check the number of registered data in the Phonebook, from the phonebook list screen, tap , then tap [Others]u[About].
Changing contacts display order 1 2 On the phonebook list screen (P.93), tap , then tap [Others]u[Contacts display order]. Tap [Japanese order]/ [Alphabetical order]/[Number order]. Displaying phonebook entries by group 1 On the phonebook list screen (P.93), tap [Groups]. 2 Tap a group. Changing accounts to display You can set registered phonebook entries to be displayed in the phonebook list. 1 2 On the phonebook list screen (P.93), tap , then tap [Others]u[Accounts to display].
Creating a new group in Phonebook 1 3 Select a required item and edit. 4 Tap [Save]. On the phonebook list screen (P.93), tap [Groups]u[Add]. When "Add" is not displayed, flick on groups to display. ･ When you set a Google account etc., you can select that account for adding. ･ 2 On the group addition screen, enter color, icon, group name, and tap [OK]. ･ The items vary depending on the account type.
Setting photo in a phonebook entry Setting ringtone 1 On the phonebook list screen (P.93), tap a phonebook entry you want to add a picture. 1 On the phonebook list screen (P.93), tap a phonebook entry to set ringtone. 2 3 4 On the profile screen, tap [Edit]. Tap [Setting] for image. Tap [Take photo]/[Select picture]. 2 On the profile screen, tap [Set ringtone]. 3 Select a ringtone and tap [Done]. When you tap [Take photo], select "Camera"/"Picture effect" to take a photo.
❖Information ･ To cancel binding, on the profile screen of the phonebook, tap , then tap [Join/ Separate]u[Separate]. 3 On the My profile screen, enter necessary information. ･ Deleting a phonebook entry 1 2 On the phonebook list screen (P.93), tap , then tap [Delete]. 4 Mark the phonebook entry you want to delete. ･ If you want to delete all phonebook entries, tap "Select all". ･ Tap [Index] to search phonebook. ･ 3 Tap [Delete]u[OK].
❖Information When sending all phonebook entries via infrared communication, you need to enter authentication password an docomo apps password. Authentication password is a 4-digit number fixed up between you and other party in advance. For the docomo apps password, see "docomo apps password" (P.139). ･ To activate infrared communication in a selected phonebook entry, tap in the profile screen, [Infrared]u[OK]u[OK].
Sharing phonebook entry currently displayed 1 2 3 On the phonebook list screen (P.93), tap , then tap [Others]u[Import/Export]. Tap [Share phonebook data]. Select sending method and follow the onscreen instructions. ･ If "Use by default for this action." checkbox is marked, application selection screen will not appear for the next time. ❖Information ･ ･ ･ ･ ･ ･ If display conditions for phonebook (P.95) are set, only phonebook entries to be displayed are exported.
5 Tap [OK]. Importing phonebook from microSD card Importing phonebook entries from docomo mini UIM card 1 Insert a microSD card in advance (P.33). 1 2 3 On the phonebook list screen (P.93), tap , then tap [Others]u[Import/Export]. Tap [Import from SD card]. When you set a Google account etc., you can select that account as an import account. ･ If there is only one file, the file is imported immediately.
Mail/Web browser sp-mode mail Send/receive mails using DOCOMO mail address (@docomo.ne.jp). You can use pictogram and Deco-mail. Mails can be received automatically. For details on sp-mode mail, refer to " ご利用ガイドブック (sp モード編 ) (Mobile Phone User's Guide [spmode]) (in Japanese only)". 1 2 From the Home screen, tap . Flick the screen upwards, then tap [ ダウンロード (Download)]. ･ After this step, follow the instructions on the screen.
･ 5 When the number of entered characters comes close to a limit, a number of enterable characters appears on the upper left of the text box. Tap [Send]. ❖Information For the character entry, see "Character entry" (P.49). You can also send/receive text messages to/from customers of overseas network operators. For details, see "Mobile Phone Users Guide [International Services]" or the DOCOMO International Services website.
Setting message (SMS) 1 From the Home screen, tap then tap [Messaging]. 2 Tap Deleting a message (SMS) , and then [Settings]. Delivery report Set whether to mark a message (SMS) you sent each time a recipient receives the message (SMS). Notifications Set whether to show message (SMS) arrival notification in the status bar. Notification Set ringtone when receiving a tone message (SMS). Notification Set whether to vibrate when vibration* receiving a message (SMS).
❖Information In Step 2, tap and tap [Delete conversations] to select a party to delete or delete all messages (SMS). ･ Email You can create an email account provided by mopera U mail, a POP3 or IMAP compatible email account provided by general ISP (provider), or an Exchange ActiveSync account to send or receive email. 4 ･ 5 1 From the Home screen, tap then tap [Email]. 2 Enter your email address and password. 3 Tap [Next].
Add video Select a file from the saved video file list to attach it. Record Start the camera to shoot a video and video attach it. Add sound WALKMAN : Select a file from the saved music file list to attach it. Sound Recorder : Record a voice message and attach it. Creating and sending email 1 From the Home screen, tap then tap [Email]. 2 3 Tap (Compose). Enter the email address of recipient. , Tap to display the contacts list screen to select from registered contacts.
1 From the Home screen, tap then tap [Email]. ･ , If you have already set an email account, tap [Inbox] to select an email account to receive. 2 On the Inbox, tap [Refresh]. 3 Tap an email you want to read. ･ and tap Email message appears. ❖Information The sender name of a received email is the name set on sender's terminal. ･ If you set "Email notifications" in Account settings (P.
Saving attachment file of email 1 From the Home screen, tap then tap [Email]. 2 Tap email with attached files and tap . ･ 3 , The attached file list is displayed. Tap [Save] of file you want to save. When attached file is not loaded, tap [Load]. ･ Tap [View] to view the attached file. ･ ❖Information The attached file is saved on the internal storage. ･ Replying/forwarding email 1 From the Home screen, tap then tap [Email]. 2 Tap email to reply or forward and tap .
Changing Email account settings 1 2 3 From the Home screen, tap then tap [Email]. Tap and [Settings]. , Tap an Email account you want to change the settings for. Change account name. Change your name (sender name). Change your signature. Register phrase that can be inserted when creating an email. Default Set to the default account to send account email, if you set two or more email accounts. Inbox check Set whether to check new messages frequency automatically and intervals of automatic check.
Setting another Email account 1 From the Home screen, tap then tap [Email]. 2 Tap and [Settings]u[ADD ACCOUNT]. Enter your email address and password. 3 ･ 4 5 If required, mark [Send email from this account by default.]. Tap [Next]. ･ To make the email account settings manually, tap [Manual setup] and follow the onscreen instructions. Set Inbox check frequency, mark required items and tap [Next].
Using mopera U Mail mopera U users can use mopera U Mail. For mopera U setting procedure, see "Setting mopera U" (P.129). In mopera U Mail, POP mail and IMAP mail are available. The mail box supports 50MB. Also, the Web mail system is available. ■ 1 POP mail From the Home screen, tap then tap [Email]. ･ 2 5 Select the security type. 6 7 Confirm the entry, then tap [Next]. Enter "mail.mopera.net" for the SMTP server and confirm the entry of "User name" and "Password" for mopera U.
Gmail Google Talk If you have a Google account, you can send/ receive emails by using Gmail on your terminal. If you have no Google account, see "Setting Google account" (P.139). ❖Information You can use Google Talk instant messaging to chat with friends. To use Google Talk, you need to make settings of your Google account. For details, refer to "Setting Google account" (P.139). Gmail messages are not displayed in Timescape. ･ Refreshing Gmail 1 From the Home screen, tap then tap [Gmail].
Early Warning "Area Mail" It is a service with which you can receive earthquake early warning, etc. delivered by the Meteorological Agency. ･ Area Mail is a free service for which subscription is not required. ･ Area Mail cannot be received in the following case.
Setting Early Warning "Area Mail" 1 2 3 From the Home screen, tap , then tap [Disaster Kit]. Tap [Early Warning "Area Mail"]. Tap Receive setting Beep tone and then [Settings]. Set whether to receive Area Mails. Set sounding time for Area Mail reception and whether to sound a dedicated ringtone even in silent mode. Check screen Check the ringtone and screen for image and reception of earthquake early warning, beep tone tsunami warning or disaster/ evacuation information.
❖Information ･ Zooming in/out a web page You can tap in Step 2 to enter search words by voice and search a web page. Going back to the previous page 1 Tap x. Adding a new tab Open multiple tabs and view web pages. 1 On the Browser screen, tap . ･ and A new tab opens in the default home page. To zoom in/out a webpage, perform any of the following operations. ･ Double-tap at the point you want to zoom in/ out.
2 Drag or to select a range of text to copy. ･ 3 4 Selected text is highlighted in blue. Tap ･ (Copy). A message "Text copied to clipboard." appears. Touch and hold the entry field on the pasting location, and tap [PASTE]. ❖Information On some web pages, selecting characters may not be available. ･ Adjusting Browser settings 1 On the Browser screen, tap and [Settings] to select an item for the Browser. Setting a home page Set home page for opening new tab.
Checking history Managing bookmarks and history 1 On the Browser screen, tap and tap [Bookmarks]uTap "History" tab. 2 Tap the time you browsed the web page, such as [Today], [Yesterday], etc. You can check history and store many bookmarks on the terminal. Bookmark a web page 1 On the Browser screen, display the web page you want to bookmark. 2 3 Tap and [Save to bookmarks]. Set label etc. and tap [OK]. ･ You can set the following options.
Settings Viewing the setting menu 1 ■ From the Home screen, tap then tap [Settings]. More... , Setting menu WIRELESS & NETWORKS DEVICE PERSONAL SYSTEM P.118 P.130 P.139 P.151 ❖Information ･ Alternatively, from the Home screen, tap and then tap [Settings], or drag the status bar downwards and tap to display the Settings screen. Wireless & networks You can make settings related to networks such as Wi-Fi, Bluetooth function. Wi-Fi Bluetooth Data usage P.118 P.122, P.161 P.
Before using Wi-Fi Turning on Wi-Fi To use Wi-Fi, turn on Wi-Fi and search available Wi-Fi network, then connect it. ･ To access the Internet using Wi-Fi, connect to Wi-Fi network in advance. 1 ❖Information ･ Make sure to receive enough signal strength for using Wi-Fi. The signal strength of the Wi-Fi network varies by the location of the terminal. Moving closer to the Wi-Fi router might enhance the signal strength.
❖Information The next time you connect to a Wi-Fi network, the security key is saved in the terminal. ･ If you enter a wrong password (security key) when selecting an access point to connect, any of the following appears. - Saved, Secured with WEP - Avoided poor Internet connection* - Authentication problem - Limited connectivity * It may take 5 minutes or more to display the message after [Connect] is tapped. Check a password (security key).
Setting the Wi-Fi network notification to ON 1 Confirm Wi-Fi is ON and from the Settings screen (P.118), tap [Wi-Fi]. 2 3 Tap and [Advanced]. Mark "Network notification". Scanning for Wi-Fi networks manually 4 Tap "Security" setting item and tap a security type of the Wi-Fi network you want to add. ･ 4 options, "None", "WEP", "WPA/WPA2 PSK", or "802.1x EAP", appear. 5 If required, enter security information for the Wi-Fi network you want to add. 6 Tap [Save]. 1 From the Settings screen (P.
Wi-Fi sleep policy By changing Wi-Fi sleep policy, you can choose to disable the Wi-Fi function in the terminal when the screen backlight turns off. You can also set the terminal to always turn on the Wi-Fi function or to always turn it on when the terminal is charged. Bluetooth Connect Bluetooth device wirelessly using Bluetooth function. For details on Bluetooth communication, see "Using Bluetooth function" (P.161).
Setting data usage limit Permitting data roaming 1 From the Settings screen (P.118), tap [Data usage]. 1 From the Settings screen (P.118), tap [Data usage]. 2 Tap [Set mobile data limit] and read the notes, and then tap [OK]. 2 Tap and [Data roaming], then read the notes and then tap [OK]. ･ "Set mobile data limit" is marked. ❖Information Note that data communication will be disabled when data usage volume reaches to the limit.
Airplane mode In this mode, the functions of using radio wave transmissions such as calling, accessing to the Internet (including sending/receiving mails), etc. are disabled. It is useful when you want to operate the terminal with no interruption of incoming calls or mails. Turning on Airplane mode 1 From the Settings screen (P.118), tap [More...]. 2 Mark [Airplane mode]. ･ When you unmark "Airplane mode", the Airplane mode turns off.
3 4 When an editing screen is displayed, follow the instruction of the network administrator to enter/set required items of VPN settings. Disconnecting a VPN 1 2 Drag the status bar downwards. Tap a notification that indicates VPN connected. Tap [Save]. 3 Tap [Disconnect]. ❖Information ･ Added VPNs can be edited/deleted. To edit VPNs, touch and hold a VPN you want to change, then tap [Edit network]. Change the VPN settings as required and tap [Save].
Setting USB tethering Setting Wi-Fi tethering Connecting the terminal to a USB compatible PC with Micro USB Cable 01 (optional), and using the terminal as a modem, you can connect the PC to the Internet. 1 From the Settings screen (P.118), tap [More...]u[Tethering & portable hotspot]. 2 3 Tap [Portable Wi-Fi hotspot]. Confirm "Details", then tap [OK]. 1 2 From the Settings screen (P.118), tap [More...]u[Tethering & portable hotspot]. Connect the terminal to a PC using a microUSB cable (P.38).
3 Enter a network SSID of the Wi-Fi access point to set. ･ 4 "Xperia AX_XXXX" is set by default. Tap "Security" setting item and tap a security type of the Wi-Fi network to set. ･ "None" and "WPA2 PSK" appear. Using Wi-Fi Direct device 1 2 From the Settings screen (P.118), tap [More...]u[Wi-Fi Direct settings]. Tap [Search]. ･ A list of detected Wi-Fi Direct devices appears. 5 Enter security information of the Wi-Fi access point to set as required. 3 6 Tap [Save].
Setting an access point An access point for connecting to the Internet (sp-mode, mopera U) is already registered. You can add or change it if necessary. By default, sp-mode (P.129) is set for the usual access point. Checking the access point in use 1 From the Settings screen (P.118), tap [More...]u[Mobile networks]u[Access Point Names]. ･ ･ Available access points (APN) appear. It is recommended that you use the displayed access point without editing.
❖Information This function is enabled by default. If disabled, access point is changed automatically and unexpected charges may apply. ･ Some applications you installed may not be operated correctly when this function is enabled. mopera U ･ Initializing an access point By initializing an access point, the default state is restored. 1 2 From the Settings screen (P.118), tap [More...]u[Mobile networks]u[Access Point Names]. Tap and tap [Reset to default].
Device Call settings You can use the network services and search for available networks. For Call settings, see "Call settings" (P.91). Vibrate on touch Set whether to vibrate the terminal for some operations such as specified software key operation. Adjusting each sound volume 1 From the Settings screen (P.118), tap [Sound]u[Volumes]. ･ Sound Set ringtones, operation sound, vibrator, etc. Set sound quality optimized for the built-in speaker.
Setting Silent mode 1 From the Settings screen (P.118), tap [Sound]u[Silent mode]. 2 Tap any of [Off]/[Vibrate]/[Mute]. ❖Information Alternatively, press and hold p for over a second and then tap / / in the pop-up screen, or drag the status bar downward and tap / / to switch Mute (Ringtone 0), Vibrate or Off (disabling Silent mode).
❖Information "Dial pad touch tones" is a sound for operations on the dial pad. "Touch sounds" is a sound for selecting menu. ･ To set the key sound of software keyboard, set from "Setting character entry" (P.62). ･ Adjusting the screen brightness 1 From the Settings screen (P.118), tap [Display]u[Brightness]. 2 Drag the slider to the right or left. 3 Tap [OK]. Display Set brightness, orientation of the screen, etc.
Setting information displayed on the unlock screen Yon can set notifications displayed on the unlock screen (P.40). ❖Information ･ To display notifications, on Preferred apps settings (P.70), set "Set all to" or "Lock screen" to "Xperia™", and set "Slide/Touch" for screen unlock method (P.147) in advance. 1 From the Settings screen (P.118), tap [Display]u[Lock screen]. ■ Displaying notification Mark "Missed calls"/"New sp-mode mails"/"New messages"/"New emails"/ "Calendar events".
Storage Check memory volume of the phone memory, internal storage, microSD card, and USB storage. And you can delete data in the internal storage, microSD card and USB storage and format. USB storage is an external memory such as a microSD card connected to the terminal using commercially available reader/writer cable. PHONE MEMORY Total space Check the phone memory for apps, available space, etc. INTERNAL STORAGE Check memory space for Apps, Total space Pictures/videos, Audio (music, ringtones, etc.
Formatting microSD card 1 From the Settings screen (P.118), tap [Storage]. 2 Tap [Erase SD card]u[Erase SD card]. ･ 3 Enter your screen unlock method as required. Tap [Erase everything]. ❖Information ･ Formatting microSD card deletes all the data in it. Formatting USB storage Insert external memory such as a microSD card into commercially available reader/ writer cable and connect the cable to the terminal in advance. 1 From the Settings screen (P.118), tap [Storage].
Apps Manage and delete installed applications, display memory usage condition, etc. or change the settings. Viewing permitted operation of the applications in the terminal You can check functions which are permitted to access to each application in the progress of performing, such as network communication function or location information function of the terminal. 1 From the Settings screen (P.118), tap [Apps]. 2 3 Tap an application to view. Flick the screen up to view permitted operations.
Deleting installed application Disabling application Before deleting installed application, back up contents related to the application that you want to save including data saved in the application. ･ Some applications cannot be deleted. You can disable some applications which cannot be uninstalled or services. Disabled applications are not displayed on the Application screen and you cannot execute them, but they are not uninstalled. ･ 1 From the Settings screen (P.118), tap [Apps].
Deleting settings for activating the application You can delete settings for activating the application and restore to the default. 1 From the Settings screen (P.118), tap [Apps]. 2 Tap an application to delete its settings. 3 Tap [Clear defaults]. Smart Connect Set to activate applications automatically when you connect the Stereo Headset with Microphone (Sample), a commercially available earphone or the AC adapter for charging. Also, set how applications operate when activating or deactivating.
PERSONAL docomo service You can set passwords for applications provided by docomo or to use the services supporting AUTO-GPS. Set to check update for applications regularly. Set to use docomo service when connecting Wi-Fi. Set a password for applications provided by docomo. docomo apps password is set "0000" by default. AUTO-GPS Set to use the services supporting AUTO-GPS. docomo location Set location information information function for imadoco search, imadocokantan search and Keitai-Osagashi Service.
❖Information You can use the terminal without creating your Google account, however the services such as Google Talk, Gmail, Google Play, etc. are not available. ･ To log in, you need a Google account and a password. ･ When you sign in, "Backup and restore" screen may appear. To backup applications, bookmark settings, etc. using Google account, mark "Keep this phone backed up with my Google Account" and then tap [Next].
1 From the Settings screen (P.118), tap [Accounts & sync]u[Add account]u[Facebook]. ･ 2 ■ If you already have a Facebook account and set account from Phonebook or Timescape of the terminal, you need not add a new account. Application control settings Sync Calendar Enter your sign in information. If you have no Facebook account, register an account. ･ If you have Facebook account, sign in. ･ Setting Xperia™ with Facebook Set Facebook account to display in the status bar.
Setting other account Removing account You can set docomo account, Evernote, Email, Corporate (Exchange ActiveSync) other than Google account (P.139) or Facebook account (P.140). 1 From the Settings screen (P.118), tap [Accounts & sync] and select a service account you want to delete. 2 Tap , then tap [Remove account]u[Remove account]. 1 From the Settings screen (P.118), tap [Accounts & sync]u[Add account]. 2 Tap an account type and follow the onscreen instructions.
5 Tap to mark an item for automatic synchronization. ･ If the items to be synchronized are marked and are displayed beside checkboxes, synchronization starts. When is not displayed, tap and tap [Sync now] to start synchronization. ❖Note Tap or drag it to the right to permit to synchronize with your Gmail, calendar, contacts, and profile information published by "Friends", etc. in Google account automatically. These communications may cause you to pay packet communications charges.
Set up SIM card lock P.146 Make passwords Set whether to show the input visible character before "・" appears on the password entry screen. Device Set whether to enable device administrators administrator. Unknown sources P.148 Trusted credentials Allow applications to access secure certificates and other credentials.*3 Install from internal Install encrypted certificates storage from internal storage. Clear credentials Clear all certificates or credential information from the credential storage*4.
･ The PUK code is written on the subscription form (copy for customer) handed at the subscription in the docomo Shop. If you subscribed other than docomo Shop, you must bring your official identification (such as drivers license), the docomo mini UIM card with you to the nearest docomo Shop or contact the "General Inquiries" on the last page.
Personal Unblocking Key (PUK code) Changing the PIN code The PUK code is an 8-digit number for canceling the locked PIN code. The PUK code cannot be changed by yourself. ･ If you failed to enter PUK code 10 times consecutively, the docomo mini UIM card is locked. Please contact a docomo Shop. ･ Enabling SIM card lock By setting PIN (security code) and entering PIN code when powered on, you can protect the docomo mini UIM card from improper use. 1 2 From the Settings screen (P.
Setting screen unlock method Changing screen unlock method 1 From the Settings screen (P.118), tap [Security]u[Screen lock]. 1 From the Settings screen (P.118), tap [Security]u[Screen lock]. 2 Tap [Slide/Touch]/[Face Unlock]/ [Pattern]/[PIN]/[Password]. 2 Enter the current unlock pattern/ PIN/password. 3 Select a new unlock method. When you tap [Face Unlock], follow the onscreen instructions to set face authentication.
If you forget how to unlock ■ ❖Information Tap [Try again] to retry entering pattern in 30 seconds. ･ When you tap [Try again]u[Forgot pattern?], the screen after tapping [Next] is displayed. ･ If you set multiple Google accounts, enter one of those accounts and password to unlock the screen. If you set "PIN"/"Password" Please contact a docomo Shop. If you set "Pattern" "Incorrect pattern" appears when you enter incorrect unlock pattern 5 times consecutively.
Language & input You can select language and input method. Language Spelling correction Personal dictionary Default Google voice typing Moji-Henshu Xperia™ Chinese keyboard Xperia™ Japanese keyboard Xperia™ keyboard Voice Search Text-to-speech output Pointer speed P.149 Set spelling correction. Register words. Set input method. P.62 ･ If you choose the wrong language and cannot read the menu texts, see the help of the following website. http://www.sonymobile.co.jp/so-01e/faq.
Backup & reset 1 Set backup of application etc. or restore the terminal to default by using Google account. Back up my data Backup account Automatic restore Data transfer mode Factory data reset Set to backup applications, settings, data, etc. to Google server. Set an account for backup to Google server. Set to restore backup settings or data when re-installing application. Set to the mode to transfer the data in the terminal using the docomo shop terminal. P.
SYSTEM Date & time You can change the date and time in the terminal. To set date/time or time zone manually, unmark "Automatic date & time" or "Automatic time zone" to disable networkprovided time/time zone in advance. Adjust date and time automatically by using network-provided information. Automatic time zone Adjust time zone automatically by using network-provided information. Set date P.151 Set time P.151 Select time zone P.151 Use 24-hour format P.152 Select date format P.
Setting the time format 1 From the Settings screen (P.118), tap [Date & time] and mark/ unmark "Use 24-hour format". ･ Mark the checkbox to shift to 24-hour format, and unmark to shift to 12-hour format. Setting the date format Accessibility You can set user support service which sounds or vibrates according to users operation and call end operation. TalkBack Large text Power button ends call 1 From the Settings screen (P.118), tap [Date & time]u[Select date format].
Developer options Put the terminal into debug mode when connecting USB or set the screen backlight to ON while charging. Keeping the screen backlight ON while charging 1 From the Settings screen (P.118), tap [Developer options]. 2 Mark "Stay awake". About phone You can check your own phone number, signal level, legal information, etc. P.250 Check your own phone number, signal level, battery level, etc. Legal information Check open source license or Google terms of use, etc.
File management Handling a file Files in the terminal should be operated on the file handling application. For example, to delete files saved in a microSD card or internal storage, use the deletion function of each application. With "Share" function of each application, you can exchange files sending to/receiving from other compatible devices via infrared communication, Bluetooth or by email file attachment.
･ 2 The terminal is connected by "Media transfer mode (MTP)" which is set by default. Follow onscreen instructions on a PC to access Internal Storage and microSD Card of the terminal. Tap [Skip]. ❖Information Screen that appears when connecting to a PC may vary depending on the operating system (OS) of a PC. ･ From the Home screen, tap and tap [Settings]u[Xperia™]u [Connectivity] to check connection mode and change the settings as follows.
Disconnecting the microUSB cable safely Dragging and dropping data on the terminal and a PC Do not disconnect the microUSB cable during data transferring. Data may be damaged. ･ If you connect the terminal in the Media transfer mode (MTP), make sure that data transfer is not in progress and just disconnect the microUSB cable. ■ Mass storage mode (MSC) Drag the status bar downwards. Tap [SD card connected]. 2 ･ ■ 1 2 3 ･ "SD card disconnected" appears in the status bar.
Connecting the terminal to a PC on a Wi-Fi network 4 Make sure that the terminal is displayed as a portable device on "Computer" the screen of the PC. If the terminal and a PC* are connected in a pair on a Wi-Fi network, automatic connection/disconnection of internal storage of the terminal with a PC is enabled when the terminal user comes in and out of the Wi-Fi area. You can easily access to files in the internal storage of the terminal from a connected PC.
❖Information From the Home screen, tap and tap [Settings]u[Xperia™]u[Connectivity] to display "Host name" (PC name) in the "TRUSTED DEVICES" field. To cancel connection setting, tap the host name and [Forget]. Until "Forget" is tapped, the connection setting retains even if you connect/ disconnect repeatedly by coming in and out of a WiFi area. ･ If the privacy separator function for Wi-Fi network (access point) is enabled, pair setting cannot be made.
Within 20cm Within ±15° from the center Infrared data port ❖Information ･ ･ ･ ･ ･ ･ Do not cover the infrared data port with the fingers, etc. while performing infrared communication. Infrared communication for the terminal conforms to IrMC version 1.1. However, some data cannot be sent or received even if the receiver's phone conforms IrMC version 1.1. Authentication password and docomo apps password may be required while sending or receiving infrared data.
3 Tap [Phonebook]/[sp-mode mail]/ [Schedule&Memo]. ･ 4 5 When you tap [sp-mode mail], select from "Inbox"/"Sent"/"Unsent". Tap [Start]. Enter docomo apps password and tap [OK]. Enter the same authentication password as that of the recipient and tap [OK]u[OK]u[OK]. ■ Sending with sharing menu of function 6 1 Select "Infrared" from the sharing menu of each application. ❖Information My profile (excluding name card) can be sent using infrared communication widget.
You may not save received data if the phone memory is full. ･ A file name may be changed when saving. A file named with 127 characters or more (Unicode) may not be saved properly. ･ Using Bluetooth function The Bluetooth function creates a wireless connection to other Bluetooth devices, for example, handsfree devices. A range within 10 meters, with no solid objects in between, is recommended. You must turn on the Bluetooth function to communicate with Bluetooth devices.
Making the terminal detectable with the Bluetooth function on 1 2 From the Home screen, tap , then tap [Settings]. Tap in Bluetooth or drag it right. ･ 3 4 appears on the status bar and Bluetooth function turns on. Tap [Bluetooth]. Tap [Xperia AX]. ･ The terminal becomes detectable by other Bluetooth devices for 2 minutes. Entering the terminal name You can name the terminal. The name appears on Bluetooth devices when you use the Bluetooth function. 1 Make sure that the Bluetooth function is on.
2 From the Home screen, tap tap [Settings]u[Bluetooth]. 3 Tap [Search for devices]. A list of detected Bluetooth devices appears. 1 4 Tap a Bluetooth device name to pair with the terminal. 2 5 Check a passkey on the "Bluetooth pairing request" screen, then tap [Pair]. 3 ･ and You can use the Bluetooth device that has been paired. ･ Some Bluetooth devices make connections continuously after making pair setting. ･ Authentication passcode may be required on the "Bluetooth pairing request" screen.
Deactivating the connection of a Bluetooth device 1 2 3 From the Home screen, tap and tap [Settings]u[Bluetooth]. Tap the connected Bluetooth device name. Tap [OK]. ･ To reconnect, tap the device name. Canceling the pair setting of a Bluetooth device 1 From the Home screen, tap tap [Settings]u[Bluetooth]. 2 Tap in a Bluetooth device name to unpair and tap [Unpair].
Sharing files with DLNA devices Using Wi-Fi function, you can share media files with other client (DLNA : Digital Living Network Alliance) devices. Set Wi-Fi connection (P.119) with another client device. Playing media files in the DLNA device with the terminal Set Wi-Fi connection with a DLNA device to allow access from the terminal in advance. 1 On the Media server settings screen, tap of "Share content" or drag it right. ･ Setting Media server "Media server turned on" appears in the status bar.
Playing a media file in the terminal with a DLNA device Connect the terminal to a DLNA device via Wi-Fi in advance. 1 On the Media server settings screen, tap of "Share content" or drag it right. ･ "Media server turned on" appears in the status bar. 2 Tap y. 3 From the Home screen, tap then tap [Album]/[Movies]. 4 5 Tap a tile you want to play. Tap and [Throw]. 6 Tap a device displayed on the "Throw" screen. ･ ･ ･ A home screen appears. , "Throw" screen appears.
Applications dmenu In dmenu, you can easily access sites recommended by DOCOMO or convenient applications. Opening dmenu 1 From the Home screen, tap [dmenu]. ･ dmarket You can obtain useful and interesting contents which meet your needs at dmarket. Opening dmarket 1 ･ Browser activates to display "dmenu". When you activate for the first time, "d マーケットソフトウェア使用許諾契約書 (License Agreement)" appears. Mark "Agree" checkbox and tap [Start use].
Play Store With Google Play, you can directly access useful applications or fun games which you can download and install on the terminal. And you can send feedback and comments about an application, or report objectionable application or incompatible application with the terminal as an inappropriate content. ･ To use Google Play, you need to set Google account (P.139). ･ Some applications and games are free of charge, and the others are paid.
Deleting application 1 From the Home screen, tap [Play Store]. 2 3 Tap and [My Apps]. Tap the applications you want to delete, then tap [Uninstall]u[OK]. ･ When you uninstall charged applications, a screen for refund may appear. For details, refer to "Help" (P.169). Help When you need help or have any questions about Google Play, display the Google Play screen, then tap and tap [Help] to open Google Play help page.
iC transfer service The iC transfer service is a service which helps you transfer all data in the IC card for OsaifuKeitai to your new Osaifu-Keitai when you change Osaifu-Keitai for changing of the model or repair. Data in the docomo mini UIM card remains the same after using the iC transfer service. Visit a sales outlet such as docomo Shop to use the iC transfer service. For details on iC transfer service, refer to " ご利 用ガイドブック (sp モード編 ) (Mobile Phone User's Guide [sp-mode]) (in Japanese only)".
Using " おサイフケータイ対応サー ビス (Osaifu-Keitai compatible service)" Using " かざしてリンク対応サービ ス (Kazashite-Link compatible service)" 1 From the Home screen, tap then tap [Osaifu-Keitai]. 1 From the Home screen, tap , then tap [Settings]u[More...]. 2 Select a service you want to use from a service list. 2 [NFC/Osaifu-Keitai settings]u[Reader/Writer, P2P]u[OK]. Download an application compatible with service site or service.
Set Reader/Writer, P2P function to ON 1 From the Home screen, tap , then tap [Settings]u[More...]. 2 [NFC/Osaifu-Keitai settings]u[Reader/Writer, P2P]u[OK]. "Reader/Writer, P2P" and "Android Beam" are marked. ･ Reader/Writer, P2P function is enabled, and appears in the status bar. ･ mark Set Reader/Writer, P2P function ON in advance (P.172). ･ Place 2 mobile phones in parallel position and point marks to each other. Do not move them until sending/receiving is complete.
Receiving data 1 Make sure that the Reader/Writer, P2P function is on. 2 Face the marks each other with the sending terminal. ･ When data is received, an application that supports the data opens. Follow the onscreen instructions. Notes on holding the mark over the other device such as a reader or device with the NFC module mark When holding mark over the other device, make sure not to hit the terminal strongly. ･ Hold the mark over parallel to the center of the other device.
❖Information Note that you cannot cancel "NFC/Osaifu-Keitai lock", if the battery runs out while "NFC/Osaifu-Keitai lock" is set. Be careful about remaining battery level. If you cancel "NFC/Osaifu-Keitai lock", charge the terminal before canceling. You need to unlock to use Osaifu-Keitai menu while "NFC/Osaifu-Keitai lock" is set. "NFC/Osaifu-Keitai lock" password is not be deleted even if you reset the terminal.
･ ･ ･ ･ ･ ･ ･ ･ ･ Depending on the settings of IP (Information Provider), the following functions may not be available. - Obtaining/Updating from the IC card reader, sharing ToruCa, moving to microSD card, copying/ displaying map Some ToruCa which can be displayed in a map from ToruCa (details) may not be displayed in a map from the ToruCa list depending on the IP settings. While "NFC/Osaifu-Keitai lock" is set, you cannot obtain ToruCa with an IC card reader.
For viewing "Data broadcasting site", etc., packet communication fees are charged. ･ Some sites require information fees. Airwaves 1Seg is one of the broadcast services and a different type of radio waves (airwaves) from that of FOMA service is received. Therefore, regardless of whether you are in or out of Xi service or FOMA service area, it cannot be received where airwaves do not reach or during broadcasting interruptions.
❖Information While emitting the sound of 1Seg with the 1Seg antenna cable SO01 connected alone, connecting the Stereo Headset with Microphone does not switch the sound output to the Stereo Headset with Microphone. To emit sound with the Stereo Headset with Microphone, remove the 1Seg antenna cable SO01 once and connect the Stereo Headset with Microphone to the 1Seg antenna cable SO01, then connect to the terminal.
c Watching 1Seg program 1 From the Home screen, tap tap [1Seg]. 2 Tap [Watch]. ■ ･ and 1Seg watching screen appears. Tap the image to temporarily view program information such as program name. 1Seg screen d e fg Data broadcasting : Display data broadcasting content. d Broadcasting station e Remote controller : Display numeric keys to switch channels and keys for searching stations. f Program guide : Display program guide.
･ If the terminal receives a call while watching 1Seg, 1Seg is interrupted and resumes after the call ends. Watching data broadcasting For data broadcasting, you can view various information by following the onscreen instructions. ❖Information ･ To watch data broadcasting, call charge or packet communication charge is not required. If you use additional services of data broadcasting, etc. via packet communication, packet communication fees are charged.
Setting 1Seg viewing 1 On the 1Seg watching screen (P.178), tap then tap [Viewing setting]. Display information for available channels. Program info Display information for received programs. Channel list Registered areas (broadcasting service area) are listed as a channel list. Add to channel Add a channel from 1Seg watching list screen. Reservation Reserve viewing or recording or display reservation results. Switch display Switch display between Video+DataBC and Data broadcasting.
Changing numbers for TV remote Initializing settings Change TV remote number assigned to each broadcasting station. Each broadcasting station can be called up via the corresponding TV remote number. You can initialize the channel setting and 1Seg setting. 1 From the Home screen, tap tap [1Seg]. and 2 Tap [Setting]u[Channel list] and tap a channel list to change. 3 Touch and hold channel information. 4 Tap [Remote control No.] and tap a broadcasting station to change.
Display TVlinks 1 On the 1Seg watching screen (P.178), tap . 2 Tap [TVlink]. 3 Select a TVlink. ･ ･ Reservation of recording/ viewing TV program Reserve recording/viewing TV program. 1 A TV link list screen appears. When selecting a link content or HTML content, tap [Yes]. ❖Information ･ Some TVlinks have period of validity. Out of date TVlinks are no longer available. Viewing/Deleting details of TVlink 1 On the 1Seg watching screen (P.178), tap .
❖Information Maximum recorded data file size is 4GB, and maximum continuous recordable time is approximately 24 hours. Items can be saved up to 99. ･ When you use the microSD card from another application during recording, recording may be failed. FM radio ･ Play a recorded program. 1 2 From the Home screen, tap tap [1Seg]. Tap [Recording data] and a program to play. You can listen to the FM radio with the terminal.
5 Tap entry box, enter a name and tap [Save]. ･ 6 The frequency bands of selected channels are registered to Favorites. To stop the FM radio, tap . ❖Information Alternatively, on the FM radio screen, tap and [Search for channels] to search. ･ You can return to the Home screen to perform another operation while listening to FM radio in the background. To return to the FM radio screen, from the Home screen, tap then tap [FM radio], or drag the status bar downward and tap [FM radio].
Camera You can shoot still pictures and videos by tapping the shutter icon or screen. You can hold the camera horizontally or vertically to shoot still pictures (when shooting with Sweep Panorama, always hold the camera horizontally). For recording videos, screen display supports landscape only. Still pictures and videos are saved automatically in the internal storage or a microSD card.
Note on Sweep Panorama In the following cases, Sweep Panorama does not work properly. - Shooting a moving object - Shooting the main object that is too close to the camera - Shooting an object with repetition of the same pattern such as a sky, beach, grass, etc. - Shooting a big object - Shooting an object with constantly changing pattern such as a wave, waterfall, etc.
h Shooting screen and key operation ■ Still picture shooting screen d e a b f c ❖Information g h ■ On the shooting screen, pinch-in/out or press m to zoom in/out. When capturing mode (P.188) is set to "Front camera", "Sweep Panorama" or "Front video", zoom is not available. ･ To end the camera, tap Navigation bar, then tap x.
Capturing mode icon ■ Capturing mode Superior auto The camera determines most suitable scene effect. A corresponding scene icon appears when the scene is recognized. "Soft snap", "Landscape", "Backlight", "Backlight portrait", "Night scene", "Night portrait", "Document", "Macro" or "Low light" is recognized. Normal A standard shooting mode. Front camera Shoot pictures using the front camera (P.199). Picture effect Apply various picture effects to pictures (P.201). Scene selection Set programmed scenes (P.
･ To shoot still pictures using auto-focus function, touch and hold the screen and release your finger when the focus frame turns green and sound beeps. A picture is taken as soon as you release the finger. If the focus frame turns red, auto-focus does not operate correctly. ❖Information When you connect Stereo Headset with Microphone (Sample), commercially available earphone set or other Bluetooth device, shutter sound may be softer.
Backlight correction HDR Correct backlight with the high dynamic range imaging function. Night portrait Suitable for shooting persons against the nightscape background. Due to long exposure time, be careful not to shake camera. Night scene Shoot a crisp and clear night scene. Due to long exposure time, be careful not to shake camera. Beach and snow Reconstruct beach and snowy scene brightly and vividly. Party Shoot an indoor picture creating good atmosphere of indoor lighting.
■ Flash Set the flash to light or not when lighting conditions are poor or in backlight. Auto Turn on the flash automatically according to the brightness. Fill flash Always turn on the flash regardless of the brightness. Red-eye reduction Reduce red-eye effect caused by the flash. Off The flash does not turn on. ･ Sometimes still picture quality can be better without flash. When you do not turn on the flash, use the self-timer to avoid blurring still picture.
■ Quick launch On the screen unlock screen, drag Quick launch icon ( ) to the left to activate the camera (P.199). Launch and capture Activate the camera to shoot a photo immediately. Launch only (still camera) Activate the camera to display shooting screen. Launch and record movie Activate the camera to record a video immediately. Launch only (movie camera) Activate the camera to display recording video screen. ■ Touch focus Tap an object on the shooting screen.
Fluorescent Adjust the color balance for lighting like fluorescent. Daylight Adjust the color balance for a sunny place. Cloudy Adjust the color balance for a cloudy sky or shaded area. ■ ■ Measure the brightness on the shooting screen to determine a well-balanced exposure automatically. Use when the capturing mode (P.188) is set to "Normal". Center Put emphasis at the center of the shooting screen and measure photometry at whole view finder to adjust the exposure.
■ Geotagging Tag photos location information (geotag) for the shooting spot. Enable the location information service setting to add Geotag. For details on location information service, see "Location services" (P.216). On Geotag (location information) is added to specify the shooting spot of the photo. Off Shooting location cannot be viewed on a map. ■ ■ Data storage Set the saving location for shot images. Appears when microSD card is inserted. Internal storage Save shot images in the internal storage.
❖Information Recording videos 1 From the Home screen, tap [Camera]. 2 Tap of photo/video switch icon (P.187). ･ Do not cover the microphone with fingers etc. when recording videos. ･ When you connect Stereo Headset with Microphone (Sample), commercially available earphone set or other Bluetooth device, shutter sound may be softer. ･ Tap the start recording icon ( )/stop recording icon ( ) or the recording screen for recording a video. For video recording screen, only landscape screen is supported.
❖Information To replace setting item icons displayed on the recording screen, tap on the recording screen and touch and hold a setting item and drag it to a dotted frame. ･ To delete a setting item icon displayed on the shooting screen, touch and hold an icon and drag it to displayed in the center of the screen. ･ or capturing mode icons (P.188) displayed on the recording screen cannot be moved or deleted. Party Shoot an indoor picture creating good atmosphere of indoor lighting.
Off The photo light does not turn on. Sometimes the video quality can be better without a photo light, even if lighting conditions are poor. Recording a good video without using the photo light requires a steady hand. ■ ■ Adjust the color balance to the light source. Auto Adjust the color balance automatically to the light source. Incandescent Adjust the color balance for lighting like incandescent bulb. Fluorescent Adjust the color balance for lighting like fluorescent.
■ Image stabilizer ■ Compensate for movements of the camera while recording a video. On Reduce blur. Off The stabilizer is not used. ■ ■ Set the recording method. On-screen button Tap the start recording icon/stop recording icon to start/stop recording a video. Touch capture Tap the recording screen to start/stop recording a video. Geotagging Tag videos location information (geotag) for the recording spot. Enable the location information service setting to add Geotag.
SD card Save recorded videos in a microSD card. ❖Note Some settings cannot be used in combination with one another. ･ Front camera Front camera allows you to shoot your own picture or video while watching the shooting screen. 1 From the Home screen, tap [Camera]. ･ 2 3 The still picture shooting screen (P.187) appears. For recording videos, tap on the photo/video switch icon (P.187) to display the video recording screen (P.187). Shoot photo/video.
❖Information To change Quick launch operations, set from the shooting screen. For details, see "Quick launch" (P.192). ･ By default, on the screen unlocking screen, tap to activate camera. ･ Setting face detection 2 Tap the frame you want to focus on or let the camera select which face to focus on without tapping. ･ 3 Each detected face is framed (up to 5 faces). A yellow frame shows the face in focus. Shoot photo/video. ･ For information on how to shoot, see "Shooting still pictures" (P.
Setting smile shutter 1 From the Home screen, tap [Camera]. ･ The still picture shooting screen (P.187) appears. 2 On the shooting screen, tap then tap [Smile Shutter]. 3 Select smile level for the smile shutter. ･ Picture effect and , Set "Off" to cancel smile shutter. Taking a photo using smile shutter 1 Set smile shutter, and point the camera at the object. Each detected face is framed (up to 5 faces). ･ The camera selects which face to focus on. A yellow frame shows the face in focus.
Taking a picture using picture effect 1 Set picture effect, and point the camera at the object. ･ 2 Shot pictures are automatically saved in the internal storage/microSD card. When you take a picture using picture effect, "Touch capture" (P.194) is not available. 1 Set Sweep Panorama, point the camera at the object. 2 Shoot a still picture. 3 Aligning the white frame with the black frame, slowly move the camera from left to right.
Playing multimedia content Photos or videos that you took with the terminal or multimedia contents (music, photos, videos, etc.) saved in the internal storage or microSD card are viewed/played in "Media Player", "WALKMAN", "Albums", etc. The terminal can play the following multimedia contents: Type Sound Still image Video File format WAV (PCM, G.711) (.wav), AAC (.3gp, .m4a, .mp4), AAC+ (.3gp, .m4a, .mp4), eAAC+ (.3gp, .m4a, .mp4), MP3 (.mp3), AMR-NB (.3gp), AMR-WB (.3gp), MIDI (SP-MIDI/GM/ GML (.
Using Stereo Headset with Microphone 1 Connect the plug of Stereo Headset with Microphone (Sample) to headset jack of the terminal. Check the connecting direction to connect correctly. Wrong connection may cause damage. ･ When Smart Connect appears, follow the onscreen instructions.
■ Album Album screen b Images, photos and videos you took can be viewed and played. Also, use Media Go to transfer content to the terminal and to take content from an external device. For details, refer to "Using microUSB cable" (P.154). a cd e Viewing photo/video 1 From the Home screen, tap then tap [Album]. ･ ･ , Album screen appears. icon is displayed on the video files. ❖Information ･ Depending on the number of saved images, it may take some times to load images.
■ Still picture viewing screen b Operating image files cde Sharing image files You can share image files by attaching to Gmail or Email, uploading to Picasa or Google+, or sending to other devices via Bluetooth or infrared communication. 1 a f a Location information ･ For a geotagged image, a country name and a region name appear, and tap the icon to view the image on the map. b Back to the image list c View share menu (P.206) d Delete image (P.
･ For shared files, file size and the file type are not particularly limited, but may be limited by the application to transfer. DRM content cannot be shared. Deleting image files 1 On the photo viewing screen/ video playing screen, tap and tap [OK]. ･ To delete several files, on the album screen, tap and [Select items], then select image files to delete, and then tap and tap [OK].
2 Tap a video to play it. Tap the screen to display play/pause icon or progress bar. Drag the marker left or right on the progress to change playing point. ･ Turn the terminal sideways to switch to the landscape view. ･ Tap x to stop playing and return to the video list screen. ･ To quit YouTube, tap y. ❖Information For movies with caption function which can display subtitles, "CC" appears on the playback screen in the landscape mode. Tap [CC] to set the caption function.
■ When the Applications screen is displayed ･ , appears on the status bar. Also, drag the status bar downwards and tap [TV launcher] to activate TV launcher. 2 Switch the TV to MHL input mode. 3 Flick an icon left or right to select application you want to use. ･ The screen of the terminal is shown on the TV screen. ❖Information ･ ･ ･ ･ ･ ･ ･ While MHL is connected, drag the status bar downwards and tap [MHL connected] to make output settings or check using a TV remote control etc.
❖Information Media Player Activating Media Player 1 From the Home screen, tap then tap [Media Player]. ･ ■ To change the order of tab icons, tap and tap [Settings]u[Arrange icons], drag up and down on the item to change then tap [Apply]. ･ Play back videos and music stored on a microSD card using Media Player. ･ For information on how to copy music and video data from a PC, see "Using microUSB cable" (P.154). ･ For information on file formats of playable data, see "Playing multimedia content" (P.
■ Music playback screen ■ Video playback screen c a c d a d e f a g h a b b i a b Back to song list Go back to the beginning of the track or to the previous track/Play or pause/Skip to the next track c Playback point ･ Appears when album art is tapped. d View optional menu e Album art f Show track information g Repeat OFF/Repeat ON/1 track repeat h Shuffle OFF/Shuffle ON i Volume control ･ Alternatively, press m during playback to adjust volume.
Play list You can play back songs in the order you decided using playlist. Editing songs in playlist 1 ■ Changing order of the songs Creating a playlist 1 2 From the Home screen, tap , then tap [Media Player]. Flick left and right on tabs at the bottom of the screen and tap [Play list]. ･ Play list screen appears. 3 Tap [Create new] and enter the access point name and tap [OK]. 4 Tap [Add songs to playlist] and select songs you want to add. You can also select songs from "Artists" and "Albums".
Initial settings for Timescape Timescape™ Timescape™ (hereinafter referred to as Timescape) displays various information such as Facebook, Foursquare, Twitter or mixi updates, etc. in chronological order. You can see a tile preview of events in chronological order before choosing to view the full content. With (infinite button), you can view all communication information related to the registered contacts (P.215).
Filter Icon Activating Timescape ■ Timescape screen a b c Displayed tile All tiles Updates from your Facebook contacts Updates from your Foursquare contacts Updates from your Twitter contacts Updates from your mixi contacts Previewing tiles Select a tile to view the content on the tile. d a b View optional menu Latest comment ･ Display the latest comments posted to Facebook/ Foursquare/Twitter/mixi.
Refreshing the Timescape screen When you refresh the Timescape screen, the terminal connects to the Internet to update information from your Facebook, Foursquare, Twitter and mixi whose accounts are set in Timescape. 1 Viewing the registered information of contacts in Timescape 1 On the Timescape screen, tap a tile. 2 Tap On the Timescape screen, tap and tap [Refresh]. Posting to Facebook, Foursquare, Twitter, mixi from Timescape 1 2 3 On the Timescape screen, tap and tap [Update status].
Location services There are two ways to find your location, using Mobile networks with Wi-Fi (Wireless network) or GPS. Wireless network technology determines your position fast but accuracy may vary. If you use GPS technology it may take a little longer, but it will find your exact position. You can enable both Wireless network and GPS to benefit from both technologies when trying to find your position. GPS function The terminal has a GPS receiver that uses satellite signals to calculate your location.
the discretion of the U.S. Department of Defense. ･ Some wireless communications products (mobile phone, data detectors and some others) block satellite signals and also causes instability of signal reception. ･ Some map displays based on location information (latitude/longitude information) may be not accurate due to some countries' or regions' regulations.
5 Read the note on location information and tap [Agree]. ･ "Google's location service" checkbox is marked. ❖Information Wireless network users' location information is stored without specifying who they are. Some location information is stored even when the application is not running. ･ 1 ･ ･ ❖Information ･ ･ ･ ･ ･ Make sure to enable the location information service setting before trying to get your position. To use Google Maps, enable data connection (LTE/ 3G/GPRS) or connect to Wi-Fi.
Searching for a location you want to look at 1 2 3 4 On the map screen, tap Fill out the search bar. . You can enter addresses, city names, business types and institution names (for example, London and art museum). ･ If a list of places searched or referred previously appears on the screen, tap an address, etc. on the list to check the location on the map. ･ Tap ･ ･ on the software keyboard. Search result appears on the map.
Getting direction Clearing the Maps Google Maps helps you receive detailed guides for your destination. Clear displayed layers, route search results and some others. 1 2 On the map screen, tap . Enter a start point in the upper entry field, and an end point in the lower entry field. ･ 3 Select a transportation from (Driving)/ (Transit)/ (Walking).
Joining Latitude You need to turn on the Wi-Fi setting beforehand. For details, see "Enabling current location search" (P.217) or "Enabling GPS function" (P.217). 1 From the Home screen, tap then tap [Latitude]. 2 Tap [MAP VIEW]. , ❖Information To set or disable Latitude, tap on the map screen, then tap [Settings]u[Location settings] to display a screen for the operation. ･ For details of Latitude, tap on the map screen, then tap [Help]u[How to]u[Additional Maps features]u[Latitude] to view the help.
Creating a schedule in Calendar 1 2 Tap on the calendar screen. Enter a name, date and time, location, description for event. ･ 3 Select the notification intervals of the schedule. ･ 4 If you have two or more calendar accounts, select one. Tap beside "Add reminder" to add a new notification. Tap [Done]. ❖Information ･ Tap in "More" and flick up the screen to set "Repetition", "Attendees", "Time zone", "Show me as:", "Privacy".
Releasing the reminder of a schedule or setting the snooze 1 If a reminder icon ( ) appears in the status bar, drag the bar downward. ･ 2 3 The reminder icon appears at set Notification time. Alarm & clock With "Alarm & clock" application, you can set an alarm and use world clock, stopwatch and timer. 1 From the Home screen, tap then [Alarm & clock]. ･ Tap a schedule. Tap [Snooze all]/[Dismiss all]. ■ Alarm screen appears.
Setting alarm 1 On the alarm screen, tap [Add alarm]. 2 Set time etc. and tap [Done]. ･ Tap [Advanced alarm settings] to view all setting items. Flick up and down on numbers to set time. Repeat Set a day of the week for the alarm. Alarm sound Set alarm sound. Snooze Set time interval to sound the duration ringtone again after stopping the ringtone. Alarm text Enter texts that appear while alarm is sounding.
Stopping an alarm while the alarm is sounding 1 While alarm is sounding, drag to the right. ❖Information If you tap [Snooze], the alarm sounds again when the time set in "Snooze duration" (P.224) has passed. ･ Using World clock Display the date and time in cities around the world. 1 On the alarm screen, tap "World clock" tab. ･ 2 3 World clock screen appears. Tap [Add city]. Select a city. ❖Information Tap to display date and time set on the terminal in full screen.
Using Stopwatch Using Timer 1 On the alarm screen, tap "Stopwatch" tab. 1 On the alarm screen, tap "Timer" tab. 2 Tap [Start]. 2 3 3 Tap [Stop]. Tap [Set time]. Flick up and down on numbers to adjust the time and then tap [Set]. Tap [Start]. Measurement starts and appears in the status bar. ･ Tap [Lap] to measure elapsed time. ･ ･ ･ Tap [Start] to resume measuring. Tap [Reset] to delete measured time and lap time.
ドコモバックアップ (docomo backup) Move or back up data such as phonebook entries, sp-mode mails, bookmarks, etc. using external memory such as microSD card. ･ Do not remove the battery pack or microUSB card during backup or restoring. Doing so may damage the terminal data. ･ If the battery is low, backup or restore may not be done. In that case, charge the terminal and retry to back up or restore. ･ docomo apps password is required to back up or restore.
Restoring 1 2 From the Home screen, tap then tap [ ドコモバックアップ (docomo backup)]. 6 2 Tap [microSD カードへ保存 (save to microSD card)]. , ･ , When you use for the first time, agree to "License agreement". When you use for the first time, agree to "License agreement". 3 Tap [Restore]. Tap [Select] on data type to restore and mark data to restore, and tap [Select]. Tap [Phonebook account copy], tap [Select] on Google account contacts you want to copy. 4 Tap [Overwrite]/[Add].
OfficeSuite With OfficeSuite, you can view files of Word, Excel, etc. from the terminal or a microSD card. ❖Information Some files may not be viewed properly due to corrupted layouts. ･ Starting OfficeSuite 1 From the Home screen, tap then tap [OfficeSuite]. ･ , OfficeSuite starts. ❖Information ･ When you activate for the first time, a screen for register name etc. appears. Follow the onscreen instructions.
International roaming Overview of International roaming (WORLD WING) With the international roaming (WORLD WING), you can use the terminal without changing phone number or mail address in the service area of the overseas network operator affiliated with DOCOMO. You do not need to change the settings of call and SMS. ■ Supporting networks The terminal is Class 4. The terminal works in a 3G roaming area and GSM/GPRS service area.
Before using Before leaving Japan To use the terminal overseas, check the following in Japan. ■ Subscription ･ ■ Charging ･ ■ Check if you subscribe WORLD WING. For details, contact "General Inquiries" on the last page. For AC adapter for charging overseas travel, use AC Adapter 03 (optional). Usage charge Overseas usage charges (call and packet communication) differ from those in Japan. ･ Some applications automatically perform packet communications. Your packet communication charges may be higher.
After arriving overseas When you arrive overseas and turn on the terminal, an available network is automatically set. Connectivity When you have set search mode of "Search mode" to "Automatic" in "Service providers" settings, optimized network is automatically selected (P.233). When you connect to the network operator conducted in flat-rate service, you can use the service with flat-rate packet communication charges overseas up to the specified upper limit per day.
After returning to Japan When you return to Japan, the terminal is connected to DOCOMO network automatically. If connection is failed, perform the following operations. ･ Set "Network Mode" to "LTE (preferred)/ WCDMA/GSM" (P.234). ･ Set "Search mode" to "Automatic" in "Service providers" settings (P.233). Making setting for international use When you start the international roaming or move out of your operator's network, you need to reconnect the terminal to another available network.
Changing network mode settings You can change network mode settings according to the network mode (communication method) adopted by the overseas network operator. 1 From the Home screen, tap then tap [Settings]. 2 Tap [More...]u[Mobile networks]u[Network Mode]. Select a network mode you use. 3 ･ , You can select from "LTE/WCDMA" "GSM only" and "LTE (preferred)/ WCDMA/GSM". If you select "LTE (preferred)/WCDMA/GSM" to switch available network automatically.
2 Dial + (touch and hold [0])uCountry codeuArea code (City code)uEnter a phone number. If the area code begins with "0", omit "0". However, "0" may be required to dial to some country or area such as Italy. ･ To call an overseas "WORLD WING" user, enter "81" (Japan) for the country code. ･ 3 Tap . ❖Information ･ During international roaming, if you make an international call to Japan using DOCOMO's phone application, the "International dialing assist" screen appears.
1 While receiving a call, touch and hold (left) and drag it to (right). 2 When the conversation is finished, tap [End call]. International roaming settings Make settings for using international roaming or international calls. ❖Information ･ When you received a call during the international roaming, regardless of which country the call is from, it is forwarded internationally from Japan. A caller is charged for a call fee to Japan, and the receiver is charged for a reception fee.
Setting incoming notification on roaming 1 From the Home screen, tap then tap . 2 Tap [Call settings]u[Roaming settings]. 3 Tap [Incoming notification on roaming]. ･ Check settings , Select items you want to use. Activate incoming call notification Deactiv. incoming call notification Check settings Tap [OK] to activate roaming incoming call notification. Tap [OK] to deactivate roaming incoming call notification. Check the current service settings.
1 From the Home screen, tap then tap . 2 Tap [Call settings]u[Roaming settings]. Tap [Network service]. 3 ･ , Select items you want to use. You need to set "Remote access" to activate. Voicemail Activate (charged) Voicemail (roaming) Deactivate Voicemail (roaming) Play Voicemail message (roaming) Voicemail settings (roaming) Voicemail ring time (roaming) Incoming call notific. (charged) Caller ID request (charged) Roaming guidance (charged) Remote operation (charged) Call Activate call Tap [OK].
Appendix/Index Optional and related devices A variety of commercially available optional devices allows you to expand the terminal's capabilities by supporting a wide range of purpose, including personal and business uses. Some accessories are only available in some areas. For details, please contact a sales outlet such as docomo Shop. For details on optional devices, see the user's manual of each device.
Check if the adapter cable and the terminal are set correctly. → P.37 ･ In case of using the AC adapter 03 (optional), is the plug of microUSB cable connected to the terminal and AC adapter or supplied desktop holder correctly? → P.36, P.37 ･ In case of using the desktop holder, are the terminal's contacts for the desktop holder dirty? Clean the contacts with a dry cotton swab etc. if they are dirty.
Operations are not possible when tapping or pressing keys. ･ Check if the power is turned off? → P.39 ･ Check if you activate the screen lock. → P.146 The screen reacts slowly when you tap or press keys. ･ When large amount of data is saved in the terminal or transferring large-size data between the terminal and microSD card, the reactions on the screen may be delayed. The docomo mini UIM card is not recognized. ･ Check if the docomo mini UIM card is attached in the right direction.→ P.
Check if the silent mode is active. → P.131 Is the ring time for Voice Mail service or Call Forwarding Service "0 Sec."? → P.91 ･ Check if you set call rejection. → P.91 Calls are not connected. (Even when moving " 圏外 (out of service area)" does not disappear, or although radio waves are enough, making/ receiving calls is unavailable.) ･ Turn the power OFF and ON, or remove and attach docomo mini UIM card. → P.32, P.34, P.
Shoot using shake reducing function. → P.193, P.198 ･ To shoot a close object, use "Superior auto" for the capturing mode. → P.188 ･ ■ 1Seg Watching 1Seg is unavailable. ･ Are you out of terrestrial digital TV broadcasting service area or in a place where airwave is weak? ･ Is channel set? → P.177 Cannot hear sound. ･ Is Stereo Headset with Microphone removed from 1Seg antenna cable SO01 when watching 1Seg using the Stereo Headset with Microphone (Sample)? → P.
The terminal suddenly became unavailable while using overseas. ･ Check if usage amount exceeds the limit of maximum charges for use. For use of "International roaming (WORLD WING)", the limit of maximum charges for use is set in advance. If exceeding the limit of maximum charges for use, pay the charges. Cannot receive calls overseas. ･ Is "Restricting incoming calls" set to "Activate restricting"? → P.
Calls cannot be made from the terminal connecting to external device such as car navigation or handsfree device. ･ If calls are made several times when the other party does not answer or is out of service, the call to this number may be disabled. In this case, turn terminal off and on. ■ Map/GPS Cannot set AUTO-GPS service information. ･ Check if the battery level is low and AUTOGPS function is stopped. If AUTO-GPS is stopped by "Lower-power operation settings", AUTO-GPS service information cannot be set.
● SIM card is locked Enter your PIN code (P.145) correctly. ● SIM card is PUK-locked Enter your PUK (Personal Unblocking Key) (P.146) correctly. ● PIN lock cancellation code is locked. PIN lock cancellation code is locked. Please contact a docomo Shop. ● The phone storage is full There is no memory space. Delete unnecessary applications (P.137) to obtain memory space.
1 Call スマートフォン遠隔サポートセン ター (Remote support center for smartphone) ( 0120-783-360, Business hours: 9:00 a.m. to 8:00 p.m., open all year round). 2 From the Home screen, tap , then tap [ 遠隔サポート (Remote support)]. ･ When you use for the first time, agree to " ソフトウェア使用許諾書 (License Agreement)". 3 Enter connection number notified by DOCOMO. 4 Remote support starts when you are connected. Warranty and After Sales Services Warranty Make sure that the warranty is received with the terminal upon purchase.
･ After Sales Services If you have problems with the terminal Before asking repair, see "Troubleshooting" (P.239) in this manual to check the problem. If the problem still persists, contact "Repairs" on the last page (in Japanese only). ■ Bring the terminal to the DOCOMO-specified repair office. However, it must be taken during business hours of the repair office. Make sure to bring a warranty card with the product when you visit the shop. Note that repair may take some days depending on the problem.
■ Parts stock period The functional parts necessary to repair the terminal will be basically available for a minimum of six years after the manufacture is discontinued. However, depending on the defective portion, repair may not be possible because of a shortage of repair parts. Note that repair may still be possible depending on the defective portion even if the stock period has expired. Contact "Repairs" on the last page (in Japanese only). Precautions ● Never modify the terminal or accessories.
● The terminal is waterproof. If inside of the terminal gets wet or moist, however, turn the power off, remove the battery pack immediately, and bring the terminal to a repair office as soon as possible. However, repair may not be possible depending on the condition of the terminal.
3 Mark "Notifications". ･ To change the notification tone, tap [Notification tone], then tap notification tone you want to change, and then tap [Done]. ❖Information If you mark "Notification vibration" in Step 3, software update is notified by vibration. ･ Downloading software updates wirelessly Downloading software to update Software can be downloaded wirelessly directly from your terminal via the Internet by using mobile network connection or by using a Wi-Fi network connection.
❖Note Note that if you tap from the Home screen, then tap [Settings]u[About phone]u[Software Update] and tap then [Settings]u[Preferred data traffic]u[Via mobile network/Wi-Fi], a Wi-Fi connection automatically switches to mobile network communications when the Wi-Fi connection is unstable and packet communication fee may apply. ･ Note that packet communication fee may apply for searching automatically.
Main specification ■ Display The terminal SO-01E Height approx. 129mmu Width approx. 65mmu Thickest part approx. 8.7mm (thickest part approx. 10.8mm) Weight Approx. 120g (with battery) Storage ROM 16GB RAM 1GB External storage microSD card of up to 2GB microSDHC card of up to 32GB (as of October, 2012) Continuous FOMA/3G Approx. 480 hours stand-by (stationary) time GSM Approx. 340 hours (stationary) LTE Approx. 350 hours (stationary) Continuous FOMA/3G Approx. 460 min. call time GSM Approx. 440 min.
Video recording size Frame rate Wireless LAN Bluetooth Video camera : 1920u1080 (Full HD) 1280u720 (HD 720p) 640u480 (VGA) Front video camera : 640u480 (VGA) 320u240 （QVGA） Max. 30 fps Compliant with IEEE802.11a*1/b/g/n*1 (Corresponding frequency band to IEEE802.11n : 2.4GHz/ 5GHz) Compliant with Bluetooth standard Ver. 4.0*2 Supported Bluetooth version Radio power Bluetooth standard Power Class 1 Available Within approx.
■ Battery Pack Product name Battery type Voltage Current ■ Battery Pack SO08 Lithium Ion Battery DC3.7V 1700mAh File format The terminal supports the display or playback of the following file format: Type Sound Still image* Video File format WAV (PCM, G.711) (.wav), AAC (.3gp, .m4a, .mp4), AAC+ (.3gp, .m4a, .mp4), eAAC+ (.3gp, .m4a, .mp4), MP3 (.mp3), AMR-NB (.3gp), AMR-WB (.3gp), MIDI (SP-MIDI/GM/ GML (.mid), XMF (.xmf ), Mobile XMF 1.0 (.mxmf ), RTTTL/RTX (.rtttl, .rtx), OTA (.ota), iMelody (.
Specific Absorption Rate of Mobile Phone, etc. Mobile phone : GSM/GPRS/EDGE 850/900/ 1800/1900 & UMTS/HSPA B1/5/6/19 & LTE B1/ 19/21 Specific Absorption Rate of Mobile Phone This model SO-01E mobile phone complies with Japanese technical regulations and international guidelines regarding exposure to radio waves.
performed over the last two decades to assess whether mobile phones pose a potential health risk. To date, no adverse health effects have been established as being caused by mobile phone use." Please refer to the WHO website if you would like more detailed information. http://www.who.int/docstore/peh-emf/ publications/facts_press/fact_english.htm Please refer to the websites listed below if you would like more detailed information regarding SAR.
standards include a safety margin designed to assure the safety of all individuals, regardless of age and health. The radio wave exposure guidelines employ a unit of measurement known as the Specific Absorption Rate (SAR). Tests for SAR are conducted using standardized methods with the phone transmitting at its highest certified power level in all used frequency bands.
* ** In the United States, the SAR limit for mobile phones used by the public is 1.6 watts/kilogram (W/kg) averaged over one gram of tissue. The standard incorporates a margin of safety to give additional protection for the public and to account for any variations in measurements. This paragraph is only applicable to authorities and customers in the United States. Europe This mobile phone model SO-01E has been designed to comply with applicable safety requirements for exposure to radio waves.
Guidelines for Safe and Efficient Use Please follow these guidelines. Failure to do so might entail a potential health risk or product malfunction. If in doubt as to its proper function, have the product checked by a certified service partner before charging or using it. ■ Recommendations for care and safe use of our products Handle with care and keep in a clean and dust-free place. ･ Warning! May explode if disposed of in fire. ･ Do not expose to liquid or moisture or excess humidity.
■ Children Warning! Keep out of the reach of children. Do not allow children to play with mobile phones or accessories. They could hurt themselves or others. Products may contain small parts that could become detached and create a choking hazard. ■ Power supply (Charger) Connect the charger to power sources as marked on the product. Do not use outdoors or in damp areas. Do not alter or subject the cord to damage or stress. Unplug the unit before cleaning it. Never alter the plug.
■ Personal medical devices ■ Mobile phones may affect implanted medical equipment. Reduce risk of interference by keeping a minimum distance of 22 cm (8.7 inches) between the phone and the device. Use the phone at your right ear. Do not carry the phone in your breast pocket. Turn off the phone if you suspect interference. For all medical devices, consult a physician and the manufacturer. ■ Some products provide GPS/Location based functions.
■ Antenna Use of antenna devices not marketed by Sony Mobile Communications AB could damage the phone, reduce performance, and produce SAR levels above the established limits. Do not cover the antenna with your hand as this affects call quality, power levels and can shorten talk and standby times. ■ Radio Frequency (RF) exposure and Specific Absorption Rate (SAR) When the phone or Bluetooth handsfree is turned on, it emits low levels of radio frequency energy.
■ Flight mode Bluetooth and WLAN functionality, if available in the device, can be enabled in Flight mode but may be prohibited onboard aircraft or in other areas where radio transmissions are prohibited. In such environments, please seek proper authorisation before enabling Bluetooth or WLAN functionality even in Flight mode. ■ Malware Malware (short for malicious software) is software that can harm the mobile phone or other computers.
■ Disposal of old electrical and electronic equipment Electronic equipment and batteries should not be included as household waste but should be left at an appropriate collection point for recycling. This helps prevent potential negative consequences for the environment and human health. Check local regulations by contacting your local city office, your household waste disposal service, the shop where you purchased the product or calling a Sony Mobile Communications AB Contact Center.
Warning! Insert the memory card as far as it will go into any memory card adapter needed. The memory card may not operate properly unless fully inserted. ･ We recommend that you make a backup copy of important data. We are not responsible for any loss or damage to content you store on the memory card.
Loudness warning! Avoid volume levels that may be harmful to your hearing. FCC Statement for the USA This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
End User Licence Agreement End User Licence Agreement Software delivered with this device and its media is owned by Sony Mobile Communications AB, and/or its affiliated companies and its suppliers and licensors. Sony Mobile grants you a non-exclusive limited licence to use the Software solely in conjunction with the Device on which it is installed or delivered. Ownership of the Software is not sold, transferred or otherwise conveyed.
About Open Source Software About Open Source Software This product includes certain open source or other software originating from third parties that is subject to the GNU General Public License (GPL), GNU Library/Lesser General Public License (LGPL) and different and/or additional copyright licenses, disclaimers and notices. The exact terms of GPL, LGPL and some other licenses, disclaimers and notices are reproduced in the about box in this product and are also available at http:// opensource.sonymobile.
Intellectual Property Right About the Copyright and Portrait rights Copyrighted contents you recorded or obtained from sites or Internet home pages using this product by downloading or other means, such as documents, images, music data, software, are prohibited from reproduction, transformation and transmission over public lines without consent of the copyright holders, unless intended for personal use or any other purpose permitted by law.
"Xperia" and "Timescape" are trademarks or registered trademarks of Sony Mobile Communications AB. ･ "Media Go" is a trademark or registered trademark of Sony Media Software and Services. ･ "PlayStation" and " " are trademarks or registered trademarks or Sony Computer Entertainment Inc. ･ "BRAVIA", "Sony", "Sweep Panorama", "WALKMAN", "xLOUD", "FeliCa", "Reader" and "Clear Phase" are trademarks or registered trademarks of Sony Corporation.
This product contains technology subject to certain intellectual property rights of Microsoft. Use or distribution of this technology outside of this product is prohibited without the appropriate license(s) from Microsoft. ･ Content owners use Microsoft PlayReady™ content access technology to protect their intellectual property, including copyrighted content. This device uses PlayReady technology to access PlayReady-protected content and/or WMDRM-protected content.
SIM unlock This terminal supports SIM unlock. If you release SIM lock, you can use SIM by a carrier other than NTT DOCOMO. ･ The SIM unlock service is provided at a docomo Shop. ･ A SIM unlock charge is separately required. ･ If you use a SIM other than by DOCOMO, LTE system is not available. Available services and functions will be limited. DOCOMO is not liable to any failures or malfunctions. ･ For details of SIM unlock, refer to NTT DOCOMO website.
Index A About phone ････････････････････････ 153 Access point Block access point change ････････････ 128 Initializing ･････････････････････････ 129 Setting････････････････････････････ 128 Accessibility ･････････････････････････ 152 Account setting Facebook･･････････････････････････ 140 Google ･･･････････････････････････ 139 Removing ･････････････････････････ 142 Accounts & sync ･･････････････････････ 139 Auto-sync ･････････････････････････ 142 Adjusting sound volume ･･･････････････ 130 Airplane mode ･･･････
Making ･････････････････････････ 85, 88 Mute ･･････････････････････････････ 89 Receiving ･･･････････････････････ 86, 88 Speaker ････････････････････････････ 88 Call forwarding service ･･････････････････ 91 Call history ･･･････････････････････････ 89 Adding to Phonebook ････････････････ 90 Deleting ･･･････････････････････････ 90 Making a call ････････････････････････ 90 Call notification････････････････････････ 92 Call settings･･･････････････････････････ 91 Call Waiting ･･･････････････････････････ 91 Caller
Receiving ･････････････････････････ 107 Replying ･･････････････････････････ 108 Saving attachment file ･･･････････････ 108 Sending ･･･････････････････････････ 106 Email account Adding ･･･････････････････････････ 110 Changing ･････････････････････････ 109 Deleting ･･････････････････････････ 110 Emergency call ････････････････････････ 85 English guidance ･･････････････････････ 92 Extensions ････････････････････････････ 67 H Facebook････････････････････････････ 140 File Commander ･･･････････････････････ 80 F
K Key icons ･････････････････････････････ 45 Kisekae ･･････････････････････････････ 73 Koe-no-Takuhaibin ･････････････････････ 91 L Landscape view ･･･････････････････････ 46 Language & input ･････････････････････ 149 Let's start PSM･････････････････････････ 79 Light sensor ･･････････････････････････ 30 Location services ････････････････ 143, 216 Location-based Wi-Fi ･･････････････････ 127 Lock screen ･･････････････････････････ 133 M Media Go････････････････････････････ 158 Media Player ･･･････････････････
Accounts to display ･･････････････････ 95 Adding a new entry ･･････････････････ 93 Combining ･････････････････････････ 97 Communication ･････････････････････ 93 Contacts display order ････････････････ 95 Deleting ･･･････････････････････････ 98 Editing ･････････････････････････････ 96 Exporting ･････････････････････････ 100 Favorites ･･･････････････････････････ 96 Groups ････････････････････････････ 95 Importing ･････････････････････････ 101 Infrared ････････････････････････････ 98 Making a call ････････････
Setup guide ･･････････････････････ 40, 150 Shabette concier･･･････････････････････ 77 Shooting still pictures ･････････････････ 188 Silent mode･･････････････････････････ 131 SIM card lock ･････････････････････････ 146 Small apps ････････････････････････････ 83 Smart Connect ･･･････････････････････ 138 Software keyboard ･････････････････････ 50 Common settings ････････････････････ 62 Keyboard skin ･･･････････････････････ 64 Software update ･･････････････････････ 250 Sound ･･････････････････････････････ 130 S
VPN ････････････････････････････････ 124 W WALKMAN ････････････････････････････ 79 Wallpaper ････････････････････････････ 73 Waterproofness/Dustproofness･･･････････ 24 Web browser ･････････････････････････ 114 Adding a tab ･･･････････････････････ 115 Adjusting settings ･･････････････････ 116 Bookmark ･････････････････････････ 117 Closing ･･･････････････････････････ 115 Copying text ･･･････････････････････ 115 Going back to the previous page ･･････ 115 History ････････････････････････････ 117 Link ･････････
Make various applications or charge your billing plan, check your charges and points, and more online. sp-mode: dmenu ⇒ " お客様サポートへ (To Customer support)" ⇒ " 各種お申込・お手続き (Various applications/procedures)" PC: My docomo (http://www.mydocomo.com/) ⇒ 各種お申込・お手続き (Various applications/procedures) (In Japanese only) * When using with sp-mode, "Network security code" is required. * When using with sp-mode, you may be charged. * "docomo ID and password" are required for use.
General Inquiries 0120-005-250 (toll free) *Service available in: English, Portuguese, Chinese, Spanish, Korean. *Unavailable from part of IP phones. (Business hours: 9:00 a.m. to 8:00 p.m.) ■From DOCOMO mobile phones (In Japanese only) (No prefix) 151 (toll free) *Unavailable from land-line phones, etc. Repairs ■From DOCOMO mobile phones (In Japanese only) (No prefix) 113 (toll free) *Unavailable from land-line phones, etc.
