F-02D INSTRUCTION MANUAL ’11.
Thank you for purchasing "F-02D" mobile terminal. Before using F-02D, read this manual to ensure safe use and handling. About manuals for F-02D The operations of F-02D are described in this manual, "使いかたガイド (Guide)” (installed in FOMA terminal) and "Instruction manual (detailed version)" (in pdf format). Instruction manual (this manual) This manual provides information about screens and operations of basic functions.
Contents FOMA terminal ................................. What you can do with F-02D........... Part names and functions ............... Usage styles ..................................... 2 3 4 6 Precautions (Always follow these directions) ..................................... Handling precautions....................... Waterproofness/Dustproofness ..... 7 16 21 Before Using ..................................... Screen Explanation .......................... Character Entry ..............................
FOMA terminal ･ F-02D supports W-CDMA, GSM/GPRS, Wireless LAN System. ･ Because your FOMA terminal uses wireless transmission, it may not function in locations where it is Introduction ･ ･ ･ ･ ･ ･ difficult for radio waves to penetrate, such as tunnels, underground passages and some buildings, in areas where radio waves are weak, or out of service area.
What you can do with F-02D Waterproofness/Dustproofness 21 docomo Palette UI 31 You can operate flicking left and right to switch MyFACEs pasted to the stand-by display. Paste function, data, etc. to the stand-by display as shortcuts. You can activate them readily just by selecting the icon. 使いかたガイド (Guide) 32 Without the instruction manual at your hand, you can check readily the operations of function.
Part names and functions Part names of F-02D and major functions assigned to each part are as follows.
To use the function with *, press the key for 1 second or more. Covering around the antenna by the hand may affect the quality. g Light that turns on when receiving a call or message or while charging h Sub-display i GPS antenna is built-in Covering around the antenna by the hand may affect the quality. j FOMA antenna is built-in Covering around the antenna by the hand may affect the quality.
Introduction m # Enter "#" or punctuation, or start/cancel Silent mode* n s (Multitask key) Start another function during a call or operation, or switch between 3D and 2D* o (Side key) Light sub-display, switch display Z (Side camera key) Activate movie shooting, record video during 1Seg watching* SD Adjusting volume S stops ring alert, alarm, vibrator or activate quick message*, D conducts mail/message inquiry*, etc.
Precautions (Always follow these directions) ・ Before using your FOMA terminal, or when DANGER WARNING CAUTION This sign denotes that death or serious injury may directly result from improper use. This sign denotes that death or serious injury may result from improper use. This sign denotes that minor injury or damage to property may result from improper use. ・ The symbols below show specific directions. This symbol denotes that the action is prohibited.
Handling FOMA terminal, battery pack, adapter, desktop holder and docomo mini UIM card (common) DANGER Introduction Do not use, store, or leave the equipment in hot areas such as near Don’t flames or in areas under strong direct sunlight such as inside a vehicle. Keep conductive materials (metal pieces, pencil lead, etc.) from coming in Don’t contact with the charging jack or external connection jack. Do not put those materials inside the terminal. May cause fire, burns, injuries, electric shock.
Do Children using the equipment should be instructed in proper operation by an adult. Do not allow them to use the equipment without adult supervision. Do not turn on the light by getting the lighting part closer to other person's Don’t eyes. When shooting infants, keep at least 1 m away from the object. May cause injuries. Do Do May be accidentally swallowed or cause injuries. Be careful especially when using FOMA terminal connected to the adapter continuously for a long time.
Do When you talk by setting handsfree or ring alert is sounding, keep FOMA terminal away from your ear. And, when connecting the earphone/ microphone etc. to the FOMA terminal and play a game or music etc., adjust the volume moderately. Do Surfaces of display and camera lens are made of plastic panels and they are structured for the glass not to scatter, however, if you mistakenly touch broken or exposed parts, you may be injured. Introduction Too loud volume may cause a hearing loss.
If the display part is accidentally broken and the liquid crystal leaks out, do not Don’t make the substance contact with your skin of face or hands. Do To use the terminal in car, check with automobile manufacturer or dealer to determine how the device is affected by radio waves before using. In rare cases, using the phone in some vehicle models can cause the vehicle's electronic equipment to malfunction. In that case, stop using the terminal immediately.
WARNING If the battery pack seems to have abnormalities such as deformation or Don’t scratches due to falling, never use it. Handling adapter and desktop holder WARNING May cause battery pack to ignite, burst, heat or leak. Introduction Do If the battery pack leaks or gives off a strange smell, immediately remove it from the vicinity of open flames. The vapors from leaking battery pack fluid may ignite or explode. Be careful not to let your pet bite the battery pack.
Do not touch the adapter cord, desktop holder or outlet with wet hands. No wet hands May cause fire, burns, electric shock. Do If incorrect voltage is used, this may cause fire, burns or electric shock. AC adapter : AC100V DC adapter : 12 or 24V DC (specific for negative ground vehicle) AC adapter for global use : Between 100V and 240V AC (Connect to the AC outlet for internal household use) If the DC adapter's fuse blows, replace it only with the specified fuse.
Handling mobile phones near electronic medical equipment ■These precautions are based on the guidelines produced at the Electromagnetic Compatibility Conference Japan, regarding the protection of electronic medical equipment from radio waves emitted by mobile phone units. Do Introduction FOMA terminal's signals may affect the performance of electronic medical equipment. WARNING Obey the following rules inside medical facilities.
When viewing 3D images, take a proper break every half hour of watching. Do Long-time viewing may cause eyestrain. Do When viewing 3D images, watch the screen straight ahead at a distance of approximately 30 cm.
Handling precautions General ・ F-02D is waterproof/dustproof, however, do not allow Introduction 16 water to seep into FOMA terminal and do not allow accessories or optional devices to get wet or let dust attach. - Battery pack, adapter, desktop holder, docomo mini UIM card are not waterproof/dustproof. Do not use in a bathroom or other highly humid area or do not let rain attached. Or putting the terminal on your body, humidity of sweat may cause internal corrosion and malfunction.
・ Do not close FOMA terminal with the strap etc. held Battery pack ・ The battery pack is a consumable part. - Replace the battery pack if FOMA terminal has extremely short operation time on a full charge, though it may vary by operating conditions. Purchase a new battery pack of the specified type. ・ Charge the battery in an area within the proper ambient temperature range (5-35℃). ・ The operation time provided by the battery pack varies by the operating environment and battery pack's deterioration.
docomo mini UIM card ・ Do not use excessive force to install/remove docomo mini UIM card. ・ Note that DOCOMO assumes no responsibility for Introduction malfunctions occurring as the result of inserting and using docomo mini UIM card with another IC card reader/writer. ・ Always keep docomo mini UIM card ICs clean. ・ Clean docomo mini UIM card with a soft, dry cloth (such as a cloth for eyeglasses). ・ Maintain a separate record of the data you saved in docomo mini UIM card.
Wireless LAN (WLAN) ・ Wireless LAN (WLAN) exchanges information using a b Cautions on using 2.
FeliCa reader/writer ・ FeliCa reader/writer function of FOMA terminal uses weak waves requiring no licenses for radio stations. ・ It uses 13.56 MHz frequency band. When using other Introduction reader/writers in your surroundings, keep FOMA terminal away sufficiently from them. Before using the FeliCa reader/writer, confirm that there are no radio stations using the same frequency band nearby. FM transmitter ・ FM transmitter of FOMA terminal uses weak waves requiring no licenses for radio stations.
Waterproofness/Dustproofness ✜ What you can do with waterproofness - If FOMA terminal gets wet with water from the swimming pool or soak in water of swimming pool, wash it in specified procedure (⇒P23). ・ You can use FOMA terminal in a bathroom. - Do not put the terminal in the bathtub. Do not use the terminal in hot water. May cause malfunction. - Never put FOMA terminal in hot spring water or water containing soap, detergent or bath powder.
After using the external/HDMI connection jack, close the cap as the direction shown in the illustration, and make sure that the cap is completely closed without slack by pushing the tabs in. Introduction ・ For installing the back cover, see "Installing back cover" of "Attaching docomo mini UIM card/ battery pack".⇒P25 ・ Securely lock the back cover and firmly close the external connection jack cap. Even a fine obstacle (one hair, one grain of sand, tiny fiber, etc.
DOCOMO does not guarantee actual operations under all states. Malfunctions deemed to be caused by inappropriate operation by the customer are not covered by the warranty. Washing FOMA terminal With pressing and holding the external connection jack cap not to open, wash the terminal in tap water without rubbing hard Press here Introduction ・ Do not move in water or slam the terminal against the surface of water with FOMA terminal opened.
Draining water from FOMA terminal When FOMA terminal is wet, water may flow out after wiping it off; drain the water in the following steps. a Wipe off moisture on the FOMA terminal surface and back side with dry, clean cloth etc. Introduction d Wipe off water drained from FOMA terminal with dry, clean cloth etc., and dry naturally. ･ Water, if any, remaining in FOMA terminal may ooze up after wiping off. ･ Do not wipe off water remaining in gaps directly with a cotton swab etc.
Before Using Attaching docomo mini UIM card/battery pack After turning power OFF, close FOMA terminal and hold it in your hand so that you can properly attach docomo mini UIM card/battery pack. ✜ Installing battery pack ✜ Removing back cover Convex parts a Slide the lever in the direction a to unlock Back cover Basic Operation b Press and slide the back cover in the arrow direction approx.
Before Using Charging The battery pack does not have a full charge at time of purchase. Use AC adapter for FOMA terminal to charge the battery before using FOMA terminal.
Before Using Power ON - Default setting Initial setting is an operation when FOMA terminal is turned ON for the first time. a f (2 sec. or more) The Initial setting screen appears. b Set required itemseC [Complete] c On a confirmation screen of software update function, geOn the confirmation screen of Error info send set., g The stand-by display appears. When a Machi-chara asks your name (user name), press g twice to enter a user name.
Screen Explanation Viewing display New arrival information and current state can be checked by the icon appearing on the screen. Major icons are as follows. a Status area Status icons are displayed. Select an area to display the status menu.
b Update notification for MyFACE⇒P31 c Machi-chara Characters moving about the screen and giving messages. In addition to the preinstalled characters, you can obtain characters by downloading. d Temperature/Humidity Temperature and humidity are displayed with the design according to TempHmd sensor set. e Pedometer/ACT monitor Steps and consumed calories of the day are displayed.
Screen Explanation Basic operations for screen and keys Menu operation On the stand-by display, select m and then perform the functions from the menu. You can select a menu item with shortcut operations, which use the keypad, etc. or with multi-cursor key operation, which uses the multi-cursor key to move the cursor.
Screen Explanation docomo Palette UI MyFACE In the right and left area of the stand-by display (vertical), up to 12 MyFACEs downloaded from sites, etc. can be pinned. a Flick left or right or h Switch screens one after another in the same way to display MyFACE you want to use. content for other than MyFACEs set by default. Note that using MyFACEs set by default is also charged if the i-mode access point is changed or while international roaming.
Basic operation on the touch panel Tap Touch the display lightly once and release the finger. The operation becomes effective when you release your finger from the display. This operation is mainly for selecting menus, items, etc. On the smart browser screen, quickly tap twice (double-tap) to zoom in/out. Basic Operation Touch (1 sec. or more) Touch the display for 1 sec. or more and release the finger. Some operations require to perform the subsequent action with your finger kept touching the screen.
Character Entry Entering characters You can enter characters by key operation and touch operation. Active input method depends on the style of FOMA terminal when you open the character entry screen. Key operation input activates in the open style and touch operation input activates in the flip style. 5-touch input is an input method to switch a character by pressing a key repeatedly.
Switching input modes Mail message editing screen a On the character entry screen, a or [TextMode] eSelect "Hiragana/Kanji", "Katakana", "Alphanumeric", "Number", etc. from the Switch input mode palette. Useful functions on the entry screen are explained taking mail message editing screen as an example.
Sound/Screen Setting Sound settings You can set tones, such as changing a ring alert, adjusting the volume, or muting the sound emitted from FOMA terminal. Ring tone You can set your favorite melody, etc. for a ring alert. Setting voice call ring tone Point ･ When Voice call ring tone is set, the setting applies to a # (1 sec. or more) appears on the stand-by display in Silent mode. Canceling Silent mode : # (1 sec.
Sound/Screen Setting Setting display Stand-by display setting You can change the default stand-by display. Setting an image Basic Operation a meh Settingea Screen/Display eb Stand-by display settingea Image/i-αppliea Vertical position or b Horizontal positionea Set image When Kisekae Tool is set, select "Yes" on the confirmation screen for canceling. b Select a foldereMove the cursor to an imageeC [OK]e"Yes" Display light You can set the brightness of screen and Light time-out.
Setting Machi-chara a meh Settingea Screen/Display ef Machi-chara settingeSet required itemseC [Set] Kisekae Tool You can set the stand-by display, menu, incoming/ outgoing call screens, etc. at once with a predefined combination. By default, Kisekae Tool matched to the FOMA terminal color is set. Setting preinstalled Kisekae Tool a mee Data Boxeh Kisekae Toole c Preinstall To display details of the Kisekae Tool, select a Kisekae Tool. To display the image of coordinate, select "Preview".
Sound/Screen Setting Light setting Indicator light You are notified of missed call or unread mail (including SMS) by the indicator light. Basic Operation a meh Settingea Screen/Display ee Each display settinged Info display & lighteb Indicator lighte a ON or b OFF Point ･ The indicator light blinks at approximately 10 seconds interval.
Lock/Security Security codes Security codes vary by functions. Security code protects personal information. Be careful about handling the security code. Terminal security code (Default : 0000) a meh Settingef Lock/Securitye c Code & Fingerprintea Change security codeeAuthenticate b Enter a new terminal security codee Enter the new terminal security code in New terminal security code-check field eC [Save] Point ･ If a wrong terminal security code is entered 5 times consecutively, the power is turned OFF.
a meh Settingef Lock/Securitye i UIM settingea Change PIN1 code or b Change PIN2 codeeAuthenticate b Enter the current PIN codeeEnter a new PIN code in New PIN code field and New PIN code - check fieldeC [Save] Point ･ To display the PIN1 code entry screen when turning Basic Operation power on, mehfica, and then set PIN1 entry ON/OFF to "ON".
Lock/Security Various lock functions All lock Menu operation is unavailable. You can use only a part of operations such as answering calls, receiving mails, turning power ON/OFF. Activate : mehfabeAuthenticate Deactivate : Enter the terminal security code (When the fingerprint authentication is set, meAuthenticate) Touch panel lock Lock touch operations with the screen off in the flip style. Activate/Deactivate : In the flip style, Z Touch lock All functions requiring communication are unavailable.
Lock/Security Lock/Security Incoming call restriction Resetting to default Call rejection setting Call reject setting allows you to reject calls from phone numbers not saved in phonebook and reject or accept calls from the specified numbers. In addition, you can set a receiving operation for each reason for hiding caller ID.
Call Telephone Making a call/videophone call Entering a phone number a Enter a phone number including area code (Up to 80 digits)en (voice call) or C (videophone call)eWhen ending the call, f To operate in flick style, set Auto rotation in Motion sensor to "ON". You can also make a call by tapping in landscape view. Point ･ Do not cover the microphone during a call. a ueSearch phonebook The phonebook list search result of the Show all names is displayed by default.
Koe-no-Takuhaibin Koe-no-Takuhaibin is a service sending messages using voice call. You can record or play messages between FOMA terminals without calling a party. You are notified by record notification SMS when a message is recorded, and by play notification SMS when the party plays a message (when the party sets play notification to on. It is set to on by default). For details, refer to NTT DOCOMO website. Recording a message Select a party and record a message in the Koeno-Takuhaibin service center.
Call Telephone Receiving a call/videophone call a Receive You are notified of an incoming call with ring alert, light alert, etc. On the display, the phone number appears when caller ID is sent, and caller's name appears when phone number is saved in the phonebook. When caller ID is not sent ,the reason (Anonymous, Payphone or Unavailable) appears. j : Adjust the alert volume S : Stop the ring alert and vibrator f : On-hold You can also answer a call by tapping the screen and then tapping .
Call Telephone When you cannot answer a call Record message Public mode When Record message is set to "ON", a greeting message is played and the caller can record message when you cannot answer the call. Public mode is an automatic answering service putting emphasis on manners in a highly public place or when driving a car. a meg TEL functioneb Record message/Voice memoed Record messageea ON Public mode (Drive mode) appears on the stand-by display.
Call Telephone Network Services Service Voice Mail Service Application Required Charged Missed Call Notification Service Not required Call Waiting Service Monthly charge Free Required Charged Call Forwarding Service Required Free Nuisance Call Blocking Service Not required Free Caller ID Notification Service Not required Free Caller ID Display Request Service Free English guidance Required Charged Not required Free Multi Number Required Charged 2in1 Required Charged OFFICEED Koe-no-T
Call Telephone Emergency call You can make the following emergency calls from the FOMA terminal. Police 110 Fire and ambulance 119 Marine emergencies 118 ･ This FOMA terminal supports "Emergency Connect 48 Location Report". When making an emergency call to 110, 119, 118, etc., information of your location (location information) is automatically informed to an emergency call receiving organization such as police.
Call Telephone Using overseas You can talk with FOMA terminal and use i-mode overseas. Communication service 3G GSM/ GSM GPRS i-Widget*5 ○ ○ International roaming (WORLD WING) is a service that allows you to make voice calls and access imode using network of telecommunications carriers affiliated with DOCOMO overseas. Before using this service, check its subscription status. For details, contact "General Inquiries" on the last page of this manual.
Making a call from the country you stay When you enter a number within 2 digits to call overseas, a screen asking for selecting "Quick dial" or "Call" appears. If you select "Quick dial", the call is made to the other party in memory No. If you select "Call", the call is made as it is (used for emergency overseas). Making an international call a 0 (1 sec. or more) Making a call to WORLD WING user overseas a 0 (1 sec.
Mail Sending i-mode mail/Sending SMS Sending i-mode mail Only by subscribing to i-mode, i-mode mails can be exchanged not only with i-mode compatible terminals but also via Internet. ･ For details of i-mode mail, refer to "Mobile Phone User's Guide [i-mode] FOMA version". a aea [Write] b Enter an address, title and texteC [Send] When sending is completed correctly, the mail is automatically saved in a folder of Outbox.
Mail Deco-mail/Decome-Anime Deco-mail Decome-Anime You can change a font size or background color, or insert still images, Deco-mail picture or Deco-mail pict. Specifying decoration before entering characters You can create more expressive Deco-mail using templates made with Flash graphics.
Mail Receiving i-mode mail No specific operations or settings are required for receiving mails (mail automatic reception). a Receive i-mode mails Point ･ By selecting a mail and then pressing C, you can reply easily using stored common phrases (Quick reply). Blinking Checking new mail/message You can make inquiry for any i-mode mail or MessageR/F delivered while you were out of service area or the power was turned OFF. a a (1 sec.
Mail Phonebook Early warning "Area Mail" Phonebook new entry This is a service that you can receive emergency earthquake flash report etc. delivered by the Meteorological Agency. i-mode subscription is not required. There are two phonebooks: the FOMA terminal phonebook and the UIM phonebook. Receiving Area Mail When an Area Mail is received, turns on, and you are notified of reception with blinking light, the dedicated buzzer or vibrate alert.
i-mode/Full Browser/Smart Browser Displaying i-mode site/website With i-mode, you can use services such as site connection, Internet connection or i-mode mail by the display of i-mode compatible terminal. You can use Full Browser or Smart Browser to display websites created for a PC. ･ i-mode is a charged service requiring subscription. For details, refer to "Mobile Phone User's Guide [i-mode] FOMA version".
Viewing and operating screen Bookmark You can bookmark frequently visited sites or websites to quickly display them the next time you want to visit. Status, title/URL*2 i-mode/Full Browser Saving : When a site or website is displayed, m [Submenu]eabe"OK"eSelect a saving folder Displaying : mebbeSelect a foldereSelect a bookmark Pointer Search 56 Scrolling up and down*1 : SD or k Scrolling up and down continuously*1 : k (1 sec.
i-Channel Using i-Channel To view the detail information of the ticker displayed, perform the following operation. a On the stand-by display, ceSelect a channel The site is connected and the detail information appears. Point ･ When the detail information of i-Channel is displayed, the same operations as the ones when imode sites or websites are available.⇒P56 Search i-Channel is a service that news, weather information, etc. is distributed to the i-Channel compatible terminal.
Map/GPS Using Map/GPS function ･ This function is unavailable as a navigation ･ Search ･ ･ ･ 58 device for aircraft, vehicles or persons or as high-precision location surveying GPS.
Map/GPS AUTO-GPS Setting AUTO-GPS Set whether to use the AUTO-GPS function. a mei Map/Overseaseg Map&GPS setting/historyee AUTOGPSeb AUTO-GPS settingea ON or b OFF Setting services provided by DOCOMO To use AUTO-GPS services that work with iconcier or services provided by DOCOMO, set whether to send your location information to DOCOMO on a regular basis. These services require separate subscriptions to use.
Camera Shooting still images/moving pictures Fast-Mo Smile-finder Tracking focus Skew correction Shooting type (Switch img/voice) Viewing shooting screen a c b Shooting still images a CePoint the camera at an object, g [ ] or Z c d e f Enjoy a Sense orientation icon b Focus frame, face detection frame c Name of detected person (Find-me focus) d Zoom rate e Available remaining time estimate f Setting icons Attach location Touch AF Auto-f
Viewing still images/moving pictures Still images/moving pictures are saved to Data Box.
1Seg Watching 1Seg Enjoy 62 ● Using 1Seg 1Seg is a service provided by TV broadcasting enterprises (stations), etc. A communication fee for receiving video picture and sound is not required. Contact NHK for details on your NHK viewing fees. * For viewing "Data broadcasting site", "i-mode site", etc., packet communication fees are charged. Some sites require information fees (i-mode pay sites). * For details of "1Seg" service, refer to the following websites.
For "Auto setting", perform the operation with extending 1Seg antenna in the digital terrestrial broadcasting service area. Select "Use preset" to load broadcasting stations and channels that are pre-registered to the FOMA terminal. b Select an areae"Yes" Watching 1Seg a T (1 sec. or more) Viewing and operating the watching screen You can watch 1Seg in full screen, or divide the screen to watch the data broadcasting.
Music Music&Video Channel Music&Video Channel is a service which automatically distributes a program of up to approximately 2 hours at night. You can also enjoy high-quality video program of up to approximately 1 hour. (In Japanese only) ･ Music&Video Channel is a charged service Enjoy 64 requiring subscription. Subscriptions to i-mode and i-mode packet flat-rate services are required for the service.
Music MUSIC Player You can play Chaku-uta full downloaded from a site and Windows Media Audio (WMA) files imported from music CDs, the Internet, etc. to a PC. And Uta-moji lyrics downloaded from a site can be displayed on the player screen by setting Link lyrics & song. * For details of MUSIC Player, refer to NTT DOCOMO website. For Windows Media Player, contact the manufacturer of your PC.
i-αppli i-αppli/i-Widget Enjoy i-αppli is a software for i-mode compatible terminals, which updates the information of stock price or weather automatically, or provides games that can be played without connecting to the network. i-Widget is a convenient function that allows you to easily access frequently-used contents and tools (Widget Appli) such as calculator, clock, memo, stock price information, etc.
i-motion/Movie Playing i-motion/movie You can obtain i-motion/movie (images, sound, etc.) from sites or websites. ✜ Playable i-motion Type Playing action Standard While the i-motion data is type (can downloaded, it is played. be saved*) ･ The downloaded i-motion can be operated in the same way as the imotion which is played after entire data is downloaded. After the entire i-motion data is downloaded, it is played. Streaming While the i-motion data is downloaded, it is played.
Osaifu-Keitai Using Osaifu-Keitai More Convenient 68 ■Osaifu-Keitai Osaifu-Keitai is equipped with IC card and allows you to pay money or to use coupon or stamp rally only by holding FOMA terminal over the IC card reader in stores etc. And you can access site or web site by holding the FOMA terminal over IC card reader, obtain the latest coupon by using communication, credit electronic money, or check the usage. Various security systems are also equipped.
i-concier Using i-concier ･ Automatic updating i-schedule/memo/ToruCa/ phonebook, etc. requires a packet communication fee separately. ･ For details, refer to "Mobile Phone User's Guide [i-mode] FOMA version". Receiving information Information is sent automatically. a Information is received lights on in the status area with light or ring alert for notification.
Convenient tools Shabette-Kensaku You can use i-mode search by speaking a keyword. a U (1 sec. or more) The FOMA terminal vibrates. For the first activation, check the guidance screen and select "Use (default)" or "Use". b Speak search keyword within 10 secondseg [Fix] The i-mode site is connected and search results appear.
Convenient tools Schedule Manage memos by Schedule or check a downloaded i-schedule. (In Japanese only) The view and function of schedule varies by the schedule type. "Normal" in which you can manage the schedules linking with i-concier or the memo list is described here.
Convenient tools Bluetooth You can establish a wireless connection between FOMA terminal and a Bluetooth device. For operations of the Bluetooth device, refer to the operation manual of your Bluetooth device. * Wireless communication is not guaranteed for all Bluetooth devices. ✜ Compatible version Bluetooth standard Version 2.
Convenient tools Wi-Fi You can make Wi-Fi connection in Access point mode (Base unit) or Client mode (Sub unit). ･ The FOMA terminal is compatible with wireless LAN standards of IEEE802.11b, IEEE802.11g and IEEE802.11n (client mode only). Base unit and client device should be compatible with the same standard to connect. ･ Note that using Wi-Fi makes battery consumption faster.
Setting Access point (APN) Set an access point to use for external connection in AP mode. a mef Toole0 Wi-Fieb Access point(main)ec Access points (APN) b I [New]eSet required itemseC [Save] c Select an access point (APN)eC [Save] Point ･ mopera U and mopera are registered by default. "mopera U 128k" is set as the access point (APN).
Data Management Using microSD card QR code for site access From PC : FMWORLD (http://www.fmworld.net/) ⇒ 携帯電話の製品情報 (Product information for mobile phone) ⇒ microSD対応状況、 microSDHC対応状況 (microSD/microSDHC support information) (In Japanese only) * The access method may be changed without previous notice. ✜ Precautions on using microSD card ･ The data saved from another device such as a PC may not be displayed or played in FOMA terminal.
Data Management Exchanging data between the FOMA terminal and microSD card Copying images to microSD card a mee Data Boxea My picturee Select a foldereMove the cursor to data When the folder list of microSD card, select "→phone". b m [Submenu]ee Move/Copye c Copy to microSDeSelect copying method Select image to copy selected itemeC, authenticate to copy all data in a folder. c "Yes" More Convenient Move the cursor to a folder to copy an iteme Press C.
Data Management Infrared communication/iC transmission You can send/receive data to/from devices such as FOMA terminal supporting infrared communication function or iC transmission function. Infrared data port 15° 15° Approx. 20 cm or less iC transmission Point ･ When sending/receiving all data items, the sender and receiver need to determine a 4-digit authentication password in advance. For infrared communication, the receiver's terminal must be ready for communication first.
Data Management Connecting to a PC More Convenient You can connect FOMA terminal to a PC to transfer WMA files or images in the microSD card. Also, connecting to the Internet for data communication is available. ･ FOMA USB Cable with Charge Function 02 (optional) or FOMA USB Cable (optional) is required. ･ To perform data transfer using data communication or DOCOMO keitai datalink, install FOMA communication configuration (driver) on a PC. For details, refer to "Manual for PC Connection".
Support Troubleshooting Check for the necessity of software update first, and update the software if necessary. ⇒P83 When checking the following items not to improve the state, contact "Repairs" on the last page of this manual (in Japanese only) or DOCOMO-specified repair office. ✜ Terminal operation ● FOMA terminal cannot be turned ON. ･ Is the battery pack installed correctly? ･ Is the battery exhausted? ● The FOMA terminal cannot be charged (the light does not turn on while charging).
Others 80 ● FOMA terminal etc. become hot while operating/ charging. While operating or charging, or if you use i-αppli, videophone call, 1Seg watching, etc. for a long time while charging the battery, FOMA terminal, battery pack and adapter may become hot. There is no problem about safety and continue to use it. ● The clock is not on time. The clock time may become wrong while turning on the power for a long time.
Support Warranty and After-Sales Service Warranty ･ FOMA terminal is provided with a written warranty. Make sure that you receive it. Check the written contents and items such as "販売店 名・お買い上げ日 (Shop name/date of purchase)" and keep it in a safe place. If it does not contain the necessary information, immediately contact the shop where you bought it. The warranty is valid for a period of one year from the date of purchase.
✜ Notes ･ Do not modify FOMA terminal or its accessories. ･ ･ ･ ･ Others 82 ･ - Repair may be refused depending on the nature of modification. The following cases may be regarded as modifications. - A sticker etc. is put on the display or keypad part - FOMA terminal is embellished with adhesive material etc. - Exteriors are replaced with other than DOCOMO's genuine parts - Repair of failures or damage caused by modification is charged even during the warranty period.
Support Updating software This function allows you to connect the network and check if software in the FOMA terminal needs to be updated, if software update is necessary, download a part of software using packet communication and update the software. When software update is required, information is posted in "お客様サポート (user support)" on NTT DOCOMO website or iMenu (in Japanese only). Software may be updated in 3 methods: "Autoupdate", "Immediate update" and "Reserved update".
Support Scanning function (Security Scan) For the data or programs that are imported to FOMA terminal, this function detects data and deletes data or inhibits activation of applications that may cause troubles. ･ The Scanning function provides a certain countermeasure against invasion of data which causes some trouble in the mobile phone, when viewing website, receiving messages, etc.
Support Options and related devices ･ Stereo Earphone Set P001*5 ･ Remote controller with microphone F01*2 ･ Earphone Terminal P001*5 ･ Wireless Earphone Set P01 ･ Wireless Earphone Set 02 ･ Bluetooth Headset F01 ･ AC adapter for Bluetooth Headset F01 ･ FOMA AC Adapter 01 for Global use*1 ･ FOMA Indoor Booster Antenna*6 ･ FOMA Indoor Booster Antenna (Stand Type)*6 ･ Bone conduction microphone/receiver 01*2/02 ･ FOMA eco Solar Panel 01 *1 When using FOMA terminal overseas, use the adapter plug that is suita
Appendix Menu list ･ Menu list for the case Select startup menu is set to "Basic menu" is described. ･ Menus indicated in red can be restored to the default by executing Reset (including the menu whose partial sub content menu will be reset to the default).
■i-αppli Music&Video Channel Software list ■Data Box i-αppli call logs My picture i-αppli run information i-αppli setting Sound effect volume 3D intensity setting Software info disp.
Bluetooth Accept registered ドコモ故障問合せ 海外紛失・盗難等 List/cnnct/discnct 海外故障 Bluetooth Power ON/OFF Bluetooth setting ■TEL function Phonebook UIM operation Add group F-LINK Home media Record message/Voice memo Record message list Voice memo list Guide Data Security Service Record voice memo Data check/Download Record message Update phonebooks Update schedule etc Dialed/Received calls Update setting information Dial/Receive call setting Caller ID notification Arrival call act microSD Steps/Activi
Call duration/charge Call charge Other network service Call waiting Reset call cost English guidance Call cost limit Remote access Hide call cost icon Multi Number Disaster Voice Messaging Koe-no-Takuhaibin Dual network Message confirm/set(site) Additional service Message confirm(voice) Settings(voice) 2in1 OFFICEED Fake call 2in1 mode switching Ph.
Text display/input Time Font size External connection HDMI Text input Bluetooth バイリンガル Wi-Fi Multilingual usage setting F-LINK/Home media Discreet display mode Femtocell Date and time setting Print setting Clock format Data exchange settings Backup/Restore Auto power ON/OFF Time tone setting Lock/Security Other setting Self mode Phone refresh Initial setting Locks Delete all data Privacy mode Reset Code & Fingerprint Software update Security indicator Error info send set.
Position location/Location notification Position location ■i-concier Notify location i-concier Maps&GPS setting/history Loc.
Appendix Main specifications ■Phone Camera section Product name F-02D Size Approx. 111 mm (H) 50 mm (W) 13.9 mm (T) (Thickest part : Approx. 18.3 mm) Weight Approx. 130 g (with battery) Continuous FOMA/3G stand-by time*1, 2, 3 GSM Stationary (Auto) : Approx. 680 H Continuous FOMA/3G call time*2, Voice call : Approx. 260 min. Videophone call : Approx. 100 min. (Substitute image displayed : Approx. 140 min.
Wireless LAN Type Conform to IEEE802.11b/g/ n*11 (Access point mode: IEEE802.11b/g) × × ■Battery Pack Quality Battery Pack F22 Battery used Li-ion battery Nominal voltage 3.
Appendix Specific Absorption Rate (SAR) of Mobile Phones Others 94 This model F-02D mobile phone complies with Japanese technical regulations and international guidelines regarding exposure to radio waves. This mobile phone was designed in observance of Japanese technical regulations regarding exposure to radio waves (*1) and limits to exposure to radio waves recommended by a set of equivalent international guidelines.
This mobile phone complies with the EU requirements for exposure to radio waves. Your mobile phone is a radio transceiver, designed and manufactured not to exceed the SAR* limits** for exposure to radio-frequency(RF) energy, which SAR* value, when tested for compliance against the standard was 0.403W/kg. While there may be differences between the SAR* levels of various phones and at various positions, they all meet*** the EU requirements for RF exposure.
Before a phone model is available for sale to the public, it must be tested and certified to prove to the FCC that it does not exceed the limit established by the U.S. government-adopted requirement for safe exposure. The tests are performed on position and locations (for example, at the ear and worn on the body) as required by FCC for each model. The highest SAR value for this model phone as reported to the FCC, when tested for use at the ear, is 0.542W/kg, and when worn on the body, is 0.519W/kg.
Important Safety Information Appendix Export Administration Regulations This product and its accessories may be under coverage of the Export Administration Regulations of Japan ("Foreign Exchange and Foreign Trade Control Laws" and the related laws and regulations). And, they are also under coverage of Export Administration Regulations of the U.S. When exporting and reexporting this product and its accessories, take necessary procedures on your responsibility and expense.
Appendix Intellectual Property Right Copyrights and portrait rights Except for the case protected by copyright laws such as personal use, use of FOMA terminal to reproduce, alter, or publicly transmit recorded pictures or sounds, or copyrighted text, images, music or software downloaded from websites without the copyright holder's authorization is prohibited. Note that taking photos or recordings at some demonstrations, performances or exhibitions may be prohibited even when only for personal use.
･ QR code is a registered trademark of Denso Wave ･ ･ ･ ･ ･ ･ ･ ･ ･ ･ This product contains software licensed by Symbian ･ ･ ･ ･ ･ ･ ･ ･ ･ ･ ･ ･ Foundation Limited. Symbian is a registered trademark of Symbian Foundation Limited. "Privacy mode" is a registered trademark of FUJITSU LIMITED. "Uni-Type" is a universal designed font jointlydeveloped by LIM Corp., Ltd. and Faculty of Engineering, Chiba University. Uni-Type is a registered trademark of LIM Corp., Ltd.
Others ･ Content owners use Windows Media digital rights ･ This product contains a module developed by the Independent JPEG Group. ･ FeliCa is a contactless IC card technology developed by Sony Corporation. ･ OMRON Corporation's Mobile OmCR is used for a character recognition engine. ･ This product contains software licensed based on ･ Others 100 Apache License V2.0. and altered as necessary by NTT DOCOMO, INC.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Others 102 <三省堂 (SANSEIDO)> デイリー日仏英・仏日英辞典（村松定史監修／三省堂 編修所編）(Daily Japanese-French-English/FrenchJapanese-English dictionary) デイリー日独英・独日英辞典（渡辺学監修／三省堂編 修所編）(Daily Japanese-German-English/GermanJapanese-English dictionary) デイリー日中英・中日英辞典（池田巧監修／三省堂編 修所編）(Daily Japanese-Chinese-English/ChineseJapanese-English dictionary) デイリー日西英・西日英辞典（上田博人、アントニ オ・ルイズ・ティノコ監修／三省堂編修所編）(Daily Japanese-Spanish-English/Spanish-JapaneseEnglish dictionary) デイリー日伊英・伊日英辞典（藤村昌昭監修／三省堂 編修所編）(Daily Japanese-Italian-English/ItalianJapanese-Eng
Index A D AC adapter ...................................................... 26 Access point mode (Base unit)...................... 73 Adjust volume................................................. 35 After-Sales Service ......................................... 81 Alarm ............................................................... 71 All lock ............................................................. 41 Attachments ................................................... 51 AUTO-GPS.........................
H Hand writing input ......................................... 33 I i-αppli .............................................................. 66 IC card lock...................................................... 41 iC transmission ............................................... 77 i-Channel ......................................................... 57 Icon .................................................................. 28 i-concier ...........................................................
R Receive setting ............................................... 54 Received calls.................................................. 43 Receiving a call ............................................... 45 Receiving a videophone call .......................... 45 Receiving i-mode mail.................................... 53 Record message ............................................. 46 Recording reservation.................................... 63 Redial ........................................................
Please ask checking/changing subscription detail, application of various services and request of various information materials online. From i-mode iMenu ⇒ お客様サポート (Support) ⇒ お申込・お手続き (Application/Procedures) ⇒ 各種お申込・お手続き (Various application/Procedures) No packet communication charges From PCs * In Japanese only My docomo (http://www.mydocomo.com/) ⇒ 各種お申込・お手続き (Various application/Procedures) * In Japanese only * You need your "Network security code" to use the site from i-mode.
General Inquiries 0120-005-250 (toll free) * Service available in: English, Portuguese, Chinese, Spanish, Korean. * Unavailable from part of IP phones. (Business hours : 9:00 a.m. to 8:00 p.m.) ■ From DOCOMO mobile phones (In Japanese only) (No prefix) 151 (toll free) * Unavailable from land-line phones, etc. ■ From land-line phones (In Japanese only) Repairs ■ From DOCOMO mobile phones (In Japanese only) (No prefix) 113 (toll free) * Unavailable from land-line phones, etc.
Manual for PC Connection Data Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Flow of setup for data transfer (OBEX communication) . . . . . . . . . . . . 4 Flow of setup for data communication . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Connecting up PC to the FOMA terminal . . . . . . . . . . . . . . . . . . . . . . . . .
Data Communication There are 3 communication modes available by connecting FOMA terminal and a PC : data transfer (OBEX communication), packet communication and 64K data communication. ･ To make packet communications or 64K data communications or edit data such as the phonebook using a PC connected, downloading the software from NTT DOCOMO website, installation and various settings are required.
❖ 64K data communication You can connect to the Internet and perform 64K data communication. Communication charges are based on the duration of the connection to the network regardless of the volume of data. Access points that support FOMA 64K data communication services such as mopera U of DOCOMO's Internet connection service or ISDN synchronized 64K access points can be used. Please be careful that a high cost will be charged for long-time communications.
◆ Usage precautions ❖ Internet service provider usage charges When using the Internet on a PC, usage charge to your Internet service provider (hereinafter referred to as Provider) is required. This charge is paid directly to the Provider, and is separated from the FOMA service charge. For details, contact your Provider. ･ DOCOMO's Internet connection service mopera U is available. mopera U is a charged service requiring subscription. ❖ Dialup connection (Provider etc.
Flow of setup for data transfer (OBEX communication) When using USB Cable, install FOMA communication configuration file (driver) in advance. Downloading FOMA communication configuration file (driver) from NTT DOCOMO website and installing Data transfer Flow of setup for data communication This section describes the setup work for performing packet communication or 64K data communication.
Wi-Fi connection (packet communication only) Setting the FOMA terminal to the AP mode For AP mode, see “Instruction manual (detail version) (In Japanese only)” (PDF file) of the FOMA terminal. Setting the connection→P25 Performing communication ◆ Precautions for installation/uninstallation ･ Before starting operation, make sure that no other program is running and exit the program if any. * Exit any resident programs on Windows including antivirus software.
◆ Inserting USB cable 1 Insert the connector of the USB cable into FOMA terminal's external connection jack horizontally. 2 Insert the other end of the USB cable connector into the PC USB port. ･ When a PC and FOMA terminal are connected, appears on the stand-by display of FOMA terminal. ❖ Removing USB cable 1 Press the USB cable's release buttons on both sides of the connector and remove the connector from FOMA terminal horizontally. 2 Remove the USB cable out from the PC.
◆ Confirming FOMA communication configuration file (driver) ･ When a PC does not detect FOMA terminal correctly, settings and communication cannot be performed. Checking on Windows 7 1 (Start)→"コントロールパネル (Control panel)"→"システムとセキュリティ (System and security)"→"デバイスマネージャー (Device manager)" in the "シ ステム (System)" category. Under Windows Vista Click (Start)→"コントロールパネル (Control panel)"→"システムとメンテナンス (System and maintenance)"→"デバイスマネージャ (Device manager)".
✔INFORMATION ･ When "FOMA F02D USB Driver" is not displayed on the deletion screen, execute the operations in "Installing FOMA communication configuration file (driver)" again and uninstall.→P6 Preparing for Bluetooth connection You can make data communication by connecting a PC compatible with Bluetooth and FOMA terminal using Bluetooth. ･ For operations of a PC, refer to the instructions manual of the PC you use.
◆ Checking modem Confirm the name of modem used on a PC or COM port number set for dialup connection. ･ When a PC does not detect FOMA terminal correctly, settings and communication cannot be performed. Checking on Windows 7 1 Click (Start)→"コントロールパネル (Control panel)"→"システムとセキュリ ティ (System and security)"→"デバイスマネージャー (Device manager)" in the "システム (System)" category. Under Windows Vista Click (Start)→"コントロールパネル (Control panel)"→"システムとメンテナンス (System and maintenance)"→"デバイスマネージャ (Device manager)".
✔INFORMATION Using pay-as-you-go data communication (including i-mode flat-rate packet communication services) ･ Note that communications of large-size data such as viewing websites containing images using packet communication and downloading (example: updating of application, music, movie, OS or anti-virus software) will require high charges.
❖ Using connection software except for DOCOMO Connection Manager DOCOMO Connection Manager includes same function as that of software below and using together is not required. Perform to change setting not to be activated or uninstall as required. ･ mopera U start up tool ･ mopera U connection & setting tool ･ FOMA PC configuration software ･ FOMA Byte counter To use Mzone (docomo Public wireless LAN service) by DOCOMO Connection Manager, uninstall the following public wireless LAN connection software.
5 Confirm the contents of ソフトウェア使用許諾契約 (Software license agreement) and if you agree to the agreement, select "使用許諾契約の条項に 同意します (Agree to the clauses of the agreement)" and click "次へ (Next)". 6 Confirm the installing folder and click "次へ (Next)". ･ To change the installation destination, click "変更 (Change)" and specify any installation destination. 7 Click "インストール (Install)". Installation starts.
8 When the "InstallShieldウィザードを完了しました (InstallShield wizard is completed)" screen appears, click "完了 (Done)". Installing DOCOMO Connection Manager is completed. ✔INFORMATION ･ Installation may take a few minutes. ･ When a message notifying you to reboot Windows is displayed, follow the instruction of screen and reboot. ･ Do not install during data communication. ◆ Starting DOCOMO Connection Manager ･ Before operating, make sure that a PC and FOMA terminal are properly connected.
✔INFORMATION ･ Just exiting the Internet browser or mail software may not disconnect communication. When you do not use communication, be sure to disconnect the communication from "切断する (Disconnect)" button of DOCOMO Connection Manager. ･ Please note that if auto update is set for OS update etc., the software is updated automatically and high cost may be charged for the packet communication fee.
◆ Setting the dialup connection (APN) ❖ The dialup connection (APN) and registration number (cid) The dialup connections (APN) for packet communication can be set for registration numbers (cid) between 1 and 10 in FOMA terminal. By default, "mopera.ne.jp" (APN) to connect to mopera is registered in cid1, "mopera.net" (APN) to connect to mopera U is registered in cid2 and 3, and "mpr.ex-pkt.net" (APN) to connect in 128K communication is registered in cid4.
3 Enter a fictional phone number (such as "0") for "電話番号 (Phone number)" →Select "接続方法 (Connection method)"→Click "OK". ･ "市外局番 (Area code)" differs depending on the PC environment. The code does not relate to Dialup connection (APN) setup. So no need to change. ･ Set as follows at "接続方法 (Connection method)" field. For USB cable connection : Select "FOMA F02D".
◆ Setting Show/Hide caller ID You can set to show/hide call ID for packet communication at once. Caller ID is your important information. Take care when deciding to disclose your caller ID. ･ If "Not notify" is set when using mopera U or mopera, connection is unavailable. Setting under Windows XP 1 2 Perform Step 1 - 4 in "Setting the dialup connection (APN)". 3 Confirm that "OK" is displayed and click "ファイル (File)"→Click "ハイパー ターミナルの終了 (End HyperTerminal)".
◆ Setting dialup network In this manual, the description takes the case of IP connection to mopera U via packet communication for example. ･ When connecting to mopera U or mopera via packet communication, enter the following number in the phone number field.
4 Enter the phone number of the dialup connection in "ダイヤルアップの電話番 号 (Dialup phone number)" ("＊99＊＊＊#" for packet communication) with one-byte→Enter "ユーザー名 (User name)"→Enter "パスワード (Password)"→Enter "接続名 (Connection name)" and click "接続 (Connect)". : The number registered in P15 "Setting the dialup connection (APN)" ･ In "ユーザー名 (User name)" and "パスワード (Password)", enter the user name and password specified by your provider or network administrator.
9 Confirm the setting of each item in "全般 (General)" tab. ･ When multiple modems are connected to a PC, set as follows. For USB cable connection : Select only "モデムFOMA F02D (Modem-FOMA F02D)" at "接続の 方法 (Connection method)" field. For Bluetooth connection : Select "モデム- (ご使用 のBluetoothリンク経由標準モデム) (Modem(Standard modem via Bluetooth link you use))" or "モデム- (Bluetooth機器メーカーが提供して いるBluetoothモデム) (Modem- (Bluetooth modem provided by Bluetooth device manufacturer))" at "接続の方法 (Connection method)" field.
❖ Setting for Windows XP 1 Click "スタート (Start)"→Select "すべてのプログラム (All programs)"→"アク セサリ (Accessories)"→"通信 (Communication)" and click "新しい接続ウィ ザード (New connection wizard)". 2 On the "新しい接続ウィザードの開始 (Start new connection wizard start)" screen, click "次へ (Next)". 3 Select "インターネットに接続する (Connect to Internet)" and click "次へ (Next)". 4 Select "接続を手動でセットアップする (Set up connection manually)" and click "次へ (Next)". 5 Select "ダイヤルアップモデムを使用して接続する (Use dialup modem to connect)" and click "次へ (Next)".
8 Enter "ユーザー名 (User name)"→Enter "パスワード (Password)"→Enter "パス ワードの確認入力 (Password confirmation entry)"→Select all items as shown below and click "次へ (Next)". ･ In "ユーザー名 (User name)" and "パスワード (Password)", enter the user name and password specified by your provider or network administrator. ･ When the access point is mopera U or mopera, you do not need to enter "ユーザー名 (User name)", "パスワード (Password)" or "パスワード の確認入力 (Password confirmation entry)".
13 Click "ネットワーク (Network)" tab→Set each item as shown below→Click " 設定 (Settings)". ･ When settings of IP and DNS information have been requested from the provider, etc. select "イ ンターネットプロトコル (TCP/IP) (Internet protocol (TCP/IP))", click "プロパティ (Property)" and set necessary information. ･ Since "QoSパケットスケジューラ (QoS packet scheduler)" settings in "この接続は次の項目を使用 します (Use these items for this connection)" can not be changed, leave it as it is. 14 Uncheck all items ( 15 Click "OK". ) and click "OK".
4 Enter "ユーザー名 (User name)"→Enter "パスワード (Password)"→Click "ダイ ヤル (Dial)". ･ In "ユーザー名 (User name)" and "パスワード (Password)", enter the user name and password specified by your provider or network administrator. ･ When using mopera U or mopera, you do not need to enter "ユーザー名 (User name)" or "パス ワード (Password)". ･ When "ユーザー名 (User name)" was entered or " パスワード (Password)" was saved while settings, these entries are no longer necessary. ･ Click "OK" when the connection established screen is displayed.
Connecting to a Wi-Fi compatible PC Even out of public wireless LAN area, you can perform packet communication with connecting a Wi-Fi compatible PC to use FOMA terminal as an access point. ･ Switch FOMA terminal to AP mode ON in advance. For AP mode settings, refer to "Instruction manual (detailed version) (in Japanese only)" (PDF file) of the FOMA terminal.
AT command AT commands are commands for setting FOMA terminal functions using a PC. FOMA terminals comply with AT commands and support some extended commands and proprietary AT commands. ❖ AT command input format "AT" must be entered before each AT command. Commands must be entered in one-byte alphanumeric characters. Connecting to mopera U with ATD command ATD＊99＊＊＊3# Return character : Press Enter key.
◆ List of AT command ･ The followings are AT command that can be used via the FOMA F02D (Modem). ･ Entering "￥" may cause "\" to appear depending on the font setting for a PC or communication software. ･ If the battery pack is removed from FOMA terminal before the terminal power is turned off, the setting values may not be recorded.
Upper slot : Command Lower slot : Example ATS4= ATS4=10 OK ATS5= ATS5=8 OK ATS6= ATS6=5 OK ATS8= ATS8=3 OK ATS10=*1 ATS10=1 OK ATS30= ATS30=0 OK ATS103= ATS103=1 OK ATS104= ATS104=1 OK ATV*1 ATV1 OK ATX*1 ATX4 OK ATZ*3 Description Set the line feed (LF) character. When result code is displayed as alphabetic characters, appends the character after the carriage return (CR) character. n=10 (fixed value) ATS4? : Display current settings Set the back space (BS) character.
Upper slot : Command Lower slot : Example AT&E*1 AT&E1 OK AT&F AT&F OK (When in offline mode) AT&S*1 AT&S0 OK AT&W Description Set the speed display used when connection is made. n=0 : Display communication speed of wireless zone n=1 : Display communication speed between a PC and FOMA terminal (default) Reset the current setting to the default. When this command is executed during communication, the terminal is reset after the line is disconnected (displaying "NO CARRIER").
Upper slot : Command Lower slot : Example AT+CBST=,1,0*1 AT+CBST=116,1,0 OK AT+CDIP=*1 AT+CDIP=0 OK AT+CEER AT+CEER +CEER : 36 OK AT+CGDCONT*2 Description Set the line to use (Setting of bearer service) n=116 : 64K data communication (default) n=134 : 64K videophone AT+CBST? : Display current settings AT+CBST=? : Display a list of assignable values Set to notify/not to notify the sub address when receiving in packet communication or 64 data communication.
Upper slot : Command Lower slot : Example AT+CNUM AT+CNUM +CNUM : ,"090XXXXXXXX", 129 OK AT+COPS=,2, *2 AT+COPS=0 OK AT+CPAS AT+CPAS +CPAS : 0 OK AT+CPIN="", "" AT+CPIN="0000" OK AT+CR=*1 AT+CR=0 OK AT+CRC=*1 AT+CRC=0 OK AT+CREG=*1 AT+CREG=0 OK AT+CUSD=,""*1 AT+CUSD=0,"012345678" OK AT+FCLASS=*1 AT+FCLASS=0 OK AT+GCAP AT+GCAP +GCAP : +CGSM,+FCLASS, +W OK Description Display FOMA terminal's own phone number in the "+CNUM : ,""," format.
Upper slot : Command Lower slot : Example AT+GMI Description Display FOMA terminal manufacturer name. AT+GMI FUJITSU OK AT+GMM Display model name of FOMA terminal. AT+GMM FOMA F02D OK AT+GMR Display FOMA terminal version. AT+GMR Ver1.00 OK AT+IFC=*1 AT+IFC=2,2 OK Set how to control local flow between a PC and FOMA terminal.
■ 64K data communication Value Description 1 Specified number does not exist. 16 Normal disconnection. 17 Communication is impossible because remote device is busy. 18 You made a call but did not receive a response within the specified time. 19 The remote device is called but no response. 21 The remote device rejected incoming calls. 63 The service and option of the network are not valid. 65 Unavailable processing speed was specified.
■ Command name : +CGEQMIN=[parameter] ･ Outline ･ ･ ･ ･ Set the criteria for judging whether to permit QoS (Quality of Service) provisioned by the network when packet communication is established.
◆ Result codes ･ When ATV command is set to n=1 (default), the result code is displayed in alphabetic characters. When the command is set to n=0, the result code is displayed numerically.→P28 ■ Result codes No.
■ Display example of result code When ATX0 is set Regardless of the settings of AT￥V command, only "CONNECT" is displayed upon completion of connection. Text display example : ATD＊99＊＊＊1# CONNECT Number display example : ATD＊99＊＊＊1# 1 When ATX1 is set ･ When ATX1, AT￥V0 (default) is set Upon completion of connection, the result code is displayed in the following format : "CONNECT ".
Kuten Code List For entering characters using code, see "Entering characters using code" in the attached manual. Note that some characters in the code input list may look different from actual ones.
1st -3rd 261 262 263 264 265 266 267 268 269 270 271 272 273 0 1 2 叉 鎖 塞 采 際 榊 搾 笹 察 鯖 捌 惨 撒 讃 賛 唆 裟 妻 犀 剤 肴 昨 匙 拶 錆 散 酸 佐 詐 哉 災 載 堺 咋 鮭 4th digit of code 3 4 5 6 7 さ 嵯 坐 宰 砕 在 咲 朔 冊 撮 鮫 桟 餐 左 座 彩 砦 材 崎 柵 刷 擦 皿 燦 斬 沙 催 栽 細 冴 鷺 索 8 9 瑳 再 歳 菜 坂 作 錯 些 砂 最 済 裁 阪 削 桜 差 挫 才 祭 罪 埼 窄 査 債 採 斎 財 碕 策 札 晒 珊 暫 殺 薩 雑 皐 三 傘 参 山 産 算 纂 蚕 残 し 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314
1st -3rd 447 447 448 449 449 450 451 452 452 453 454 455 456 4th digit of code 0 1 2 3 4 5 6 7 紋 門 匁 や 也 冶 夜 爺 耶 矢 厄 役 約 薬 訳 躍 靖 鑓 ゆ 愉 愈 油 癒 諭 輸 唯 佑 優 勇 友 悠 憂 揖 有 柚 湧 涌 猶 祐 裕 誘 遊 邑 郵 雄 融 よ 余 揚 窯 養 与 揺 羊 慾 誉 擁 耀 抑 輿 曜 葉 欲 預 楊 蓉 沃 傭 様 要 浴 8 9 野 弥 柳 薮 宥 幽 猷 由 夕 予 幼 妖 容 庸 洋 溶 熔 用 謡 踊 遥 陽 翌 翼 淀 ら 456 457 458 羅 雷 洛 絡 落 酪 藍 蘭 覧 螺 裸 来 莱 頼 乱 卵 嵐 欄 濫 り 458 459 460 461 462 463 464 465 履 李 痢 葎 掠 隆 竜 両 凌 糧 良 厘 林 466 瑠 塁 涙 累 類 利 吏 梨 裏 略 龍 寮 諒 淋 理 裡 劉 侶 料 遼 燐 璃 里 流 慮 梁 量 琳 離 溜 旅 涼 陵 臨 陸 琉 虜 猟 領 輪 律
1st -3rd 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 696 697 698 699 700 701 702 703 704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 0 瞽 砌 碚 碾 礫 禊 秕 稟 穢 窖 竊 竦 笞 筧 箚 箴 簇 簟 籘 粭 粽 糲 紵 經 緇 緘 縡 縵 繙 辮 纎 罟 羇 羮 翦 耙 聚 聿 胛 脛 腦 膣 臂 臠 舍 艝 艷 苣 苞 茯 茣 莨 菷 菻 蒂 蒿 蒡 蓼 薨 藉 蘊 虍 蚋 蛔 蜀 蜷 蝴 螽 蟯 1 瞻 砒 碌 碼 磧 祀 禝 秧 禀 穩 窩 竍 竭 笵 筺 筰 箋 篆 簓 簷 籟 粢 糀 糴 紂 絆
