Owner’s Manual SR606 • Line Mixer • Distribution Amp • Buffer Amp A Harman International Company
Warning For your protection, please read the following: Water and Moisture: Appliances should not be used near water (e.g. near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc.) Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. These symbols are internationally accepted symbols that warn of potential hazards with electrical products.
SR606 INTRODUCTION Congratulations, and thank you for your purchase of the DOD SR606 Line Mixer/Distribution Amp. The DOD SR606 is one of the most flexible sound reinforcement tools available on the market today. It can be used as a distribution amp, line mixer, buffer amp, or any combination of the three. The SR606 is laid out in a logical and simplistic format. Each channel has its own level and pan control.The stereo inputs and stereo outputs have their own level adjustment as well.
2 SR606 FRONT PANEL 3 1 2 4 5 6 1. Master Input Level - Controls the signal strength entering the Left and Right Inputs. 2. Channel 1-6 Level - Controls the signal strength entering the 1-6 inputs, being delivered to the 1- 6 Outputs, or being delivered to the Left and Right Outputs, depending on your application. 3. Channel 1-6 Pan - Controls the Left/Right position being delivered from Channels 1-6 to the Stereo Outputs, or Selects which Stereo Input Channel 1-6 is receiving its signal from. 4.
SR606 REAR PANEL 4 1 2 3 5 6 1. Power Receptacle - Connect the detachable Power cord from here to an AC outlet 2. Main Output - These Left and Right Outputs can receive signal from the Left and Right Inputs, or the Channel 1-6 Inputs, or a combination, depending on your application. 3. Channel 1- 6 Outputs - The Channel 1-6 Outputs can receive signal from the Main Inputs, or from the Channel 1- 6 Inputs, or a combination, depending on your application. 4.
4 SR606 INSTALLATION Install the SR606 in a rack with the provided rack screws. Route the AC power cord to a convenient power outlet away from audio lines. The unit may be turned on and off using the front panel power switch. Since the units draw a relatively small amount of current during idle, they can be left on continuously. The DOD SR606 generates very little heat during operation and thus does not need to be specially ventilated or cooled.
SR606 DISTRIBUTION AMP To use the SR606 as a distribution amp connect your source signal to either the Left, Right, or Left and Right Inputs. Connect as many of the 1 through 6 Outputs as desired.You may also use the Left and Right Outputs for a total of 8 Outputs. The signal coming in to the Left/Right Inputs will be delivered to the 1 through 6 Channel Outputs. The Level control of each Channel will adjust the volume at each individual Channel Output.
6 SR606 SPECIFICATIONS Input Connectors: Input Impedance: Maximum Input Level: Input Gain: Output Connectors: Output Impedance: Maximum Output Level: Frequency Response: THD+N: SNR: Dynamic Range: 8 1/4” TRS balanced 20K balanced 22dBu -98dB to +6dBu 8 1/4” TRS balanced 200 ohms balanced 22dBu 10Hz. to 22KHz. .015% Ref. +4dBu @ 1KHz. 90dB to mix outputs 108dB DOD WARRANTY 1. The warranty registration card must be mailed within ten days after purchase date to validate this warranty. 2.
DECLARATION OF CONFORMITY Manufacturer’s Name: DOD Electronics Manufacturer’s Address: 8760 S.
V ISIT DOD E LECTRONICS ON THE WORLD W IDE W EB HTTP :// WWW. DOD. COM AT DOD E LECTRONICS C ORPORATION 8760 S OUTH S ANDY PARKWAY S ANDY, U TAH 84070 T ELEPHONE 801-566-8800 FAX 801-566-7005 I NTERNATIONAL D ISTRIBUTION 8760 S OUTH S ANDY PARKWAY S ANDY, U TAH 84070 T ELEPHONE 801-568-7638 FAX 801-568-7642 DOD IS A R EGISTERED T RADEMARK OF H ARMAN M USIC G ROUP I NC .