TABLE OF CONTENTS SECTION PAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1 1 INTRODUCTION 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4 UNDERSTANDING YOUR INSTRUMENT PANEL 5 STARTING AND OPERATING 6 WHAT TO DO IN EMERGENCIES 7 MAINTAINING YOUR VEHICLE 8 MAINTENANCE SCHEDULES 9 IF YOU NEED CONSUMER ASSISTANCE 10 INDEX . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS m Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m Van Conversions/Campers . . . . . . . . . . . . . . . . . 5 m How To Use This Manual . . . . . . . . . . . . . . . . . . 5 m Vehicle Identification Number . . . . . . . . . . . . . . . 6 m Warnings And Cautions . . . . . . . . . . . . . . . . . . . 5 m Vehicle Modifications / Alterations . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION HOW TO USE THIS MANUAL Consult the table of contents to determine which section contains the information you desire. The detailed index, at the rear of this manual, contains a complete listing of all subjects. WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle.
INTRODUCTION VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is found on a stamped plate located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment. NOTE: It is illegal to remove the VIN plate.
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS 1 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . . .11 ▫ Power Door Locks — If Equipped . . . . . . . . . .17 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .11 ▫ Child Protection Door Lock . . . . . . . . . . . . . . .21 ▫ Sentry Key — If Equipped . . . . . . . . . . . . . . . .11 m Remote Keyless Entry — If Equipped . . . . . . . . .22 m Ignition And Steering Lock . . . . . . . . . . . . . . . . .14 ▫ To Unlock The Doors . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE m Security Alarm System — If Equipped . . . . . . . . .29 ▫ Rearming Of The System . . . . . . . . . . . . . . . . .29 ▫ To Set The Alarm . . . . . . . . . . . . . . . . . . . . . .29 ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .30 ▫ Enhanced Driver Seat Belt Reminder System (BeltAlert) . . . . . . . . . . . . . . . . . . . . . . . . . . .43 ▫ Seat Belts And Pregnant Women . . . . . . . . . . . .44 ▫ Seat Belt Extender . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to order duplicate keys from your dealer or a locksmith. If you received your keys without the bag, ask your dealer to give you the number.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The 9Security Light9, located in the instrument cluster, will illuminate for about 2 seconds when the ignition switch is first turned to the ON position. If the vehicle electronics do not receive a valid signal from the ignition key, the 9Security Light9 will flash continuously to signal that the vehicle has been immobilized. If the 9Security Light9 remains on during vehicle operation, it indicates a fault in the system electronics.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Customer Key Programming You can program new keys to the system if you have two valid keys by doing the following: 1. Insert the first valid key into the ignition and turn the ignition to the ON position for at least 3 seconds but no longer than 15 seconds. Turn the ignition back to the OFF position and remove the first key. 2. Insert the second valid key and switch the ignition to the ON position within 15 seconds.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE IGNITION AND STEERING LOCK Manual Transmissions When the steering wheel is in the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your vehicle. It may be difficult to turn the key from the LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until it turns easily.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Automatic Transmissions In the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your vehicle. It may be difficult to turn the key from the LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until it turns easily. The key can be inserted or withdrawn only in the LOCK position. Push in on the key in the ignition lock cylinder to rotate to the LOCK position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR KEY The same key used to start the vehicle is also used to unlock the doors. To unlock the vehicle doors, insert the key into the lock and turn. To lock the doors, insert the key and turn. WARNING! For personal security and safety in the event of an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. DOOR LOCKS Manual Locks Front and Rear doors may be locked, by moving the lock plunger up or down.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Power Door Locks — If Equipped NOTE: Vehicles equipped with remote keyless entry do not have a passenger side door lock cylinder. Vehicles equipped with power door locks can be locked or unlocked from inside by either the use of the door lock switches located on the front doors or by pressing the LOCK or UNLOCK buttons on the Remote Keyless Entry key fob (if equipped).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Central Locking — If Equipped Vehicles with security will have a feature called 9Central Locking9. When the key is placed in the door cylinder and turned to the 9Unlock9 position, the security will be disarmed, the illuminated entry will be turned on and that door will be mechanically unlocked. If the key is once again turned to the unlock position within 5 seconds of the first unlock, the remaining doors will unlock.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Fasten your seat belt (Fastening the seat belt will cancel any chiming that may confuse you during this programming procedure). 3. Place the key into the ignition. 4. Within 10 seconds cycle the key from the OFF position to the ON position four times; ending in the ON position ( Do not start the engine ). 5. Within 30 seconds, press the driver’s door lock switch in the LOCK direction. 6. A single chime will be heard to indicate the feature has been disabled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Unlock Feature Programming This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedure: Customer Programming sequence to disable or enable: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may be confusing during this programming procedure). 3. Insert the key into the ignition. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the childprotection door lock system. 21 To use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! REMOTE KEYLESS ENTRY — IF EQUIPPED Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To unlock the doors: Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, the parking lights will flash on twice and if installed, the cargo lamp will turn on for 30 seconds. The system can be programmed to unlock all the doors upon the first UNLOCK button press by using the following procedure: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To lock the doors: Press and release the LOCK button on the transmitter to lock all doors. If the ignition is OFF, when the doors are locked, the parking lights will flash on once and the horn will chirp once. The horn chirp feature will be shipped from the assembly plants activated. If desired this feature can be disabled by using the following procedure: 1. Enter your vehicle and close all doors. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Vehicles will be shipped from the assembly plants with the park lamp flash feature activated. If desired, this feature can be disabled by using the following procedure: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may confuse you during this programming procedure). 3. Place the key into the ignition. 4. Turn the ignition to the ON position ( Do not start the engine ). 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE automatically cancel after 3 minutes or if the vehicle is started and exceeds 15 mph. During the Panic Mode, the door locks and remote keyless entry systems will function normally. Panic mode will not disarm the security system on vehicles so equipped. Programming Additional Transmitters Vehicles with the keyless entry option will be shipped from the assembly plants with two key fob transmitters programmed only for that vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9. A single chime will be heard. The chime indicates that the fob has been recognized. 10. Within 4 seconds of hearing the chime, press and release any button on the fob being programmed. 11. A single chime will be heard. The chime indicates that the fob has been programmed. 12. Repeat steps 8 to 11 for a total of 4 fobs. 13. Turn the ignition to the OFF position or wait 60 seconds to exit program mode. 14.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. Transmitter Battery Service 1. With transmitter buttons facing down, use a flat blade or dime to pry the two halves of the transmitter apart. Make sure not to damage the rubber gasket during removal. 2. Remove and replace the batteries.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SECURITY ALARM SYSTEM — IF EQUIPPED This system monitors the vehicle doors and ignition for unauthorized operation. When the alarm is activated, the system provides both audible and visual signals. For the first 3 minutes the horn will sound and the headlights and security telltale will flash repeatedly. For an additional 15 minutes only the headlights and security telltale will flash. The engine will run only if a valid Sentry Key is used to start the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Disarm the System: Use the Keyless Entry transmitter or the key to turn the driver’s door lock to the unlock position. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the security lamp will flash for 30 seconds. Check the vehicle for tampering. The Security system will also disarm, if the vehicle is started with a programmed Sentry Key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WINDOWS Power Windows—If Equipped 2 The control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of Quad Cab models. The windows will operate only when the ignition switch is turned to the ON or ACC (Accessory) position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Down (Driver’s Side Only) The driver’s window switch has an Auto Down feature. Press the window switch past the detent, release, and the window will go down automatically. Window Lockout Switch (4 Door Models Only) The window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window lock button.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WIND BUFFETING Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Research has shown that seat belts save lives, and that they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” WARNING! • A belt buckled into the wrong buckle will not protect you properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. 37 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 WARNING! Detaching Buckle with Key 2. To reattach the seat belt to the front center seat, pull the black buckle latch plate forward from the cab back panel and insert it into the black keyed buckle until there is an audible click. Refer to the previous section for the proper seat belt usage.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Inserting Latch Plate In Use Position WARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Press the button located on the upper belt guide, and then move it up or down to the position that serves you best. 41 As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How To Disengage The Automatic Locking Mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly. The pretensioners are triggered by the airbag control module. Like the airbags, the pretensioners are single use items. After a collision that is severe enough to deploy the airbags and pretensioners, both must be replaced.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled. Seat Belts and Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. 4. Turn off the engine. A single chime will sound to signify that you have successfully completed the programming.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! 45 These airbags are certified to the new Federal regulations that allow less forceful deployments. Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. • Do not mount any aftermarket equipment such as trailer brake controllers, snowplow controllers, auxiliary light switches, radios, etc.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Infants in rear facing child restraints must NEVER ride in the front seat of a vehicle with a passenger front airbag unless the airbag is turned off (Standard Cab Vehicles Only). An airbag deployment can cause severe injury or death to infants in that position. See the Passenger Airbag On/Off Switch section. • If your vehicle does not have a rear seat, see the Passenger Airbag On/Off Switch section.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag System Components The airbag system consists of the following: • Airbag Control Module • AIRBAG Readiness Light • Driver Airbag The Window Airbag System, on vehicles equipped, consists of the following: • AIRBAG Readiness Light (shared with the front airbag system) • Window Bags Above the Side Windows.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The airbag control module also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or RUN positions. These include all of the items listed above except the knee bolsters, the instrument panel, and the steering wheel and column.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • When the airbag control module detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the airbags. The airbag covers separate and fold out of the way as the airbags inflate to their full size. The airbags fully inflate in milliseconds. This is less time than it takes you to blink your eyes. The airbags then quickly deflate while helping to restrain the driver and front passenger.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE because the infant has a medical condition which makes it necessary for the driver to be able to see the infant, • is a child, age 1 to 12 who must ride in the front seat because there is no rear seat, because there is no rear seat position available, or because the child has a medical condition which makes it necessary for the driver to be able to see the child, • has a medical condition which makes passenger airbag inflation (deployment) a greater risk for the
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Turn On the Passenger Airbag (Standard Cab Vehicles Only) If you do have a collision which deploys the airbags, any or all of the following may occur: Place the ignition key in the Passenger Airbag On/Off Switch, push the key in and turn counterclockwise, and remove the key from the switch. This will turn on the passenger airbag. The “Off” light near the switch will be off when the ignition switch is turned to the ON position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning. • It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags will not be in place to protect you. WARNING! Deployed airbags can’t protect you in another collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE bags to inflate, it signals the inflators on the crash side of the vehicle. A quantity of nontoxic gas is generated to inflate the window bag. The inflating window bag pushes the side pillar molding out of the way and covers the window.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Airbag Light You will want to have the airbags ready to inflate for your protection in an impact. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system promptly: NOTE: If the speedometer, tachometer or any engine related gauges are not working, the airbag control module may also be disabled. The airbags may not be ready to inflate for your protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position. • Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips for getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE outboard positions and also feature tether strap anchorages, which must be used, located behind the seatback (refer to Child Restraint Tether Anchor later in this section). Identification dots are located above the standard cab front seat lower anchorages as a guide for locating lower anchors. NOTE: For children riding in the front seat of a Standard Cab model refer to the “Passenger Airbag On/Off Switch” located in this section.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing the Child Restraint System WARNING! Do not install child restraint systems equipped with LATCH attachments in the center position of a Quad Cab model rear seat. The LATCH anchorages in this seat are designed for the two outboard seating positions only. A child may be placed in the rear center seating position of a Quad Cab model using the seat belt and child tether anchorage. Failure to follow this may result in serious or fatal injury.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 WARNING! WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. An incorrectly anchored tether strap could lead to seat failure and injury to the child.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tether Anchorage Points at the Right and Center Front Seat (Regular Cab - All Seats) 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back under the head restraint to the tether anchor directly behind the seat. 2. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Multiple Child Restraint Installation Sequence (Quad Cab Rear Seats) 3. Pass each tether strap hook under the head restraint and through the loop of webbing behind the child seat. 1. Obtain tether straps by raising the head restraints and reaching between the rear glass and rear seat. The tether strap may be retained with an elastic band. Accessibility to the tether strap is greatly improved by raising the seat cushion to the “up” position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Multiple Child Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few thousand miles of operation. This is a normal part of the break-in and is not an indication of difficulty. CAUTION! • During the first 500 miles (805 km) your new vehicle is driven, do not tow a trailer. Doing so may damage your vehicle. • Limit your speed to 50 mph (80 km/h) during the first 500 miles (805 km) of towing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lock Your Vehicle Always remove the keys from the ignition and lock all doors when leaving the vehicle unattended, even in your own driveway or garage. Try to park your vehicle in a well-lighted area and never invite theft by leaving articles of value exposed. Exhaust Gas WARNING! Exhaust gases contain carbon monoxide, a potentially toxic gas that by itself is colorless and odorless.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.) or if the front airbags have deployed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS m Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 ▫ Inside Mirror . . . . . . . . . . . . . . . . . . . . . . . . .75 ▫ Automatic Dimming Mirror— If Equipped . . . .76 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .76 ▫ Exterior Mirrors Folding Feature . . . . . . . . . . .77 ▫ Electronic Power Mirrors — If Equipped . . . . . .77 ▫ Electric Rear Window Defroster And Heated Sideview Mirrors — If Equipped . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Adjustable Head Restraints . . . . . . . . . . . . . . .93 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . 102 ▫ Manual Rotary Lumbar Support Adjustment — If Equipped . . . . . . . . . . . . . . .94 ▫ Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . . 103 ▫ Power Seats — If Equipped . . . . . . . . . . . . . . .95 ▫ Heated Seats — If Equipped . . . . . . . . . . . . . .96 m To Open And Close The Hood . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 ▫ To Set At A Desired Speed . . . . . . . . . . . . . . . 110 ▫ Average Fuel Economy (AVG ECO) . . . . . . . . 116 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . . 110 ▫ Distance To Empty (DTE) . . . . . . . . . . . . . . . 116 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . . 110 ▫ Trip Odometer (ODO) . . . . . . . . . . . . . . . . . . 116 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . . 111 ▫ Elapsed Time (ET) . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Erasing Homelink Buttons . . . . . . . . . . . . . . . 124 m Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 ▫ Reprogramming a Single Homelink Button . . . 125 ▫ Center Storage Compartment — If Equipped . . 129 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 ▫ Storage And Seats — If Equipped . . . . . . . . . . 130 m Electrical Power Outlets . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 MIRRORS Inside Mirror The mirror should be adjusted to center on the view through the rear window. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror— If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side convex mirror. Some vehicles will not have a convex right side mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The controls for the power mirrors are located on the driver’s door trim panel. Set the top switch to the left or right for the left or right mirror, and set it to the center off position to prevent accidentally moving a mirror when you are finished adjusting the mirror. To adjust a mirror, select left or right with the top switch, and press one of the four arrows for the direction you want the mirror to move.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or outboard, the mirror head should be rotated (flipped Out or In). A small blindspot mirror is integrated onto the main mirror surface. 3 HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in-vehicle communications system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE “Call” or “Dial”). Your cellular phone’s audio is transmitted through your vehicle’s stereo system; the system will automatically mute your radio before receiving or sending a call. UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s microphone for private conversations. The UConnect™; phone book enables you to store up to 32 names and four numbers per name.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ system can be used with any Hands Free Profile certified Bluetooth™ cellular phone. If your cellular phone has a different profile (i.e. headset profile), you will not be able to use any UConnect™ features. The UConnect™ system is fully integrated into your vehicle, including your vehicle’s stereo system. All voice prompts as well as the other party’s voice in a conversation will be played over your vehicle’s stereo system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will be asked to say a four-digit pin number into the UConnect™ system which you will later need to enter into your cellular phone during the cellular phone pairing process. You can enter any four-digit pin number. You will not need to remember this pin number after the initial registration process. • The UConnect™ system will then prompt you to begin the cellular phone pairing process on your cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 • After the 9Ready9 prompt, say 9Dial9 or 9Call9 wait for the ready prompt followed by the name and designation of a phonebook entry that you wish to dial. For example, you can say 9Call John Doe Work9. After you are finished adding an entry into the phonebook, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu. phonebook from which you can choose. To select one of the entries from the list, press the 9Voice Recognition9 button while the UConnect™ system is playing the desired entry and say 9Delete9.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the 9Ready9 prompt, say 9Phonebook List Names9. • The UConnect™ system will play the names of all the phonebook entries. • To call one of the names in the list, press the ’Voice Recognition’ button during the playing of the desired name and say 9Call9. • The UConnect™ system will then prompt you as to number designation you wish to call. • The selected number will be dialed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, press the ’Phone’ button to place the current call on hold and answer the incoming call. To reject the incoming call, you can disregard the call and continue with your current conversation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Three-Way Calling To initiate three-way calling, press the ’Voice Recognition’ button while a call is in progress and make a second phone call. When the second call is established, press the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call. Call Termination To end a call in progress, press the ’Phone’ button. All calls in progress will be terminated.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will be asked to say the name of the phone that you wish to delete. You can either say the name of the phone that you wish to delete or you can say 9All9 to delete all the phones. • After the 9Ready9 prompt, say 9Setup List Phones9 and the UConnect™ system will play the phone names of all paired cellular phones in order from highest priority to lowest priority.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The lower priority phone will only be used for the next phone call. After that, the UConnect™ system will return to using the highest priority phone in the vehicle. UConnect™ System Features Barge In - Touch Tone Phone Inputs You can use your UConnect™ system to access a voice mail system, an automated service, or any other phone number that you can dial with any phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g. the UConnect™ system will not repeat a phone number before you dial it). • Press the ’Phone’ button to begin. • After the 9Ready9 prompt, say 9Setup Confirmation9. The UConnect™ system will play the current confirmation prompt status and you will be given the choice to change it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Help If you need assistance at any prompt or if you want to know what your options are at any prompt, say 9Help9. The UConnect™ system will play all the options at any prompt if you ask for help. Cancel At any prompt, you can say 9Cancel9 and you will be returned to the previous menu. Emergency Assistance If you are in an emergency, say 9Dial Emergency9 or 9Call Emergency9 and the UConnect™ system will instruct your cellular phone to call 911.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 40-20-40 Front Seat Each outboard seat is independently adjustable forward or backward and is equipped with a back recliner. The manual seat adjustment handle is found at the front edge of each seat cushion. Pull up on the handle and slide the seat to get the most comfortable position. WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Seats The recliner handle is on the outside of the seat cushion. Pull up on the handle to release the seat back and adjust for comfort. 93 WARNING! You can be seriously, even fatally injured riding in a seat with the seatback reclined. Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. If you ride in this position, the shoulder harness will no longer be restraining you.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To lower the head restraint, push in the button and then push down on the head restraint. Manual Rotary Lumbar Support Adjustment — If Equipped Rotating the lumbar control knob on the left side of the driver’s seatback and on the right side of the passenger’s seatback increases or decreases the lumbar support.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Power Seats — If Equipped CAUTION! Don’t put anything under a power seat. It may cause damage to the seat controls. 3 Up, Down, Forward, and Rearward The power seat controls are on the outboard side of the front seat cushions. Three switches control the seat movement. The four-way switch in the center can be moved forward or backwards to get the most comfortable position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE control seat height. Change the seat angle by using the two toggle switches, tilting it up or down. Tilt Adjustment Heated Seats — If Equipped The heated seat switches are located in the instrument panel under the climate controls. The engine must be running for the heated seats to operate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Each heated seat switch has two settings (HI and LOW). Press the switch once to obtain the desired heating position and press a second time in the same direction to turn the heated seats OFF. If you do not purposefully turn the switch OFF, the heating element in the seat will remain activated until the ignition is turned off. The indicators on the switch will illuminate when the heated seats are in the (HI or LOW) position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are latched fully before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS 99 Interior Lights 3 Courtesy/ dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the second upward detent position, or if equipped, when the UNLOCK button is pressed on the key fob.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE turn on the cargo light located on the back of the cab. When a door is open and the interior lights are on, rotating the dimmer control all the way down to the OFF detent will cause all the interior lights to go out. This is also known as the 9Party9 mode because it allows the doors to stay open for extended periods of time without discharging the vehicle’s battery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlamp Delay — If Equipped To aid in your exit, your vehicle, if equipped, can be programmed by your dealer with a headlamp delay that will leave the headlamps on for 0, 30, 60, or 90 seconds. This delay is initiated when the ignition is turned OFF while the headlamp switch is on, and then the headlamp switch is cycled off. The headlamps will remain on for 60 seconds.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO LIGHT The cargo lights are turned on by rotating the dimmer control to the optional fully upward position. The cargo lights will also turn on for 30 seconds when a key fob Unlock is pressed, as part of the illuminated entry feature. MULTIFUNCTION CONTROL LEVER The multifunction control lever is located on the left side of the steering column. Turn Signals Move the lever up or down to signal a right-hand or left-hand turn.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Passing Light You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steering wheel. This will cause the high beam headlights to turn on until the lever is released. High Beam / Low Beam Select Switch Pull the multifunction control lever fully toward the steering wheel to switch the headlights from HIGH or LOW beam.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wipers 105 Intermittent Wiper System 3 The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed. The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The delay interval decreases as you rotate the knob until it enters the LO continual speed position. The delay can be regulated from a maximum of about 15 seconds between cycles, to a cycle every 2 seconds. The delay intervals will double in duration when the vehicle speed is 10 mph (16 km) or less. WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Push the lever back up to lock the column firmly in place. 107 WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER ADJUSTABLE PEDALS — IF EQUIPPED Adjustment 1. Position the driver seat so that you are at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel. 2. Fasten and adjust the seatbelts. 3. Move the adjustable pedal switch, located to the left of the steering column near the parking brake release, in the direction you desire to move the pedals. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over accelerator operation at speeds greater than (refer to the table below for the speed for your specific engine).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Set At A Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. To Deactivate A soft tap on the brake pedal, normal braking, clutch pressure while slowing the vehicle, or pressing the CANCEL button will deactivate speed control without erasing the memory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Vary The Speed Setting When the speed control is on, speed can be increased by pressing and holding the ACCEL button. When the button is released, a new set speed will be established. Tapping the ACCEL button once will result in a speed increase (refer to the table below for the speed for your specific engine). Each time the button is tapped, speed increases so that tapping the button three times will increase speed by three increments.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: When driving uphill, at elevations above 2,000 feet (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE— IF EQUIPPED The two optional overhead consoles may consist of the following features: 113 Courtesy/Reading Lights In the middle of the console are two courtesy/reading lights. Both lights illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (fully upward position), or when the UNLOCK button is pressed on the Remote Keyless Entry transmitter, if so equipped.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE WITH COMPASS/TEMPERATURE MINI-TRIP COMPUTER — IF EQUIPPED This optional overhead console consists of the following: This overhead console allows you to choose between a compass/temperature display and one of four trip conditions being monitored. US/M Button • Courtesy Lights • Compass/Temperature Mini-Trip Computer (CMTC) Use this button to change the display from U.S. to metric measurement units.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE RESET Button 115 Global Reset If the RESET button is pressed twice within 4 seconds while in any of the 3 resettable displays, the Global Reset will reset all 3 displays. Step Button Use this button to reset the following displays to zero: Average Fuel Economy Trip Odometer Elapsed time Use this button to choose or cycle through the four trip conditions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. This display mode becomes less sensitive to instantaneous changes in fuel consumption as the number of total vehicle miles since the last reset increases. It is suggested that this mode be reset periodically for general operation or when driving conditions change significantly (for example, at the end of a trip or when a trailer is connected or disconnected).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Elapsed Time (ET) This display shows the accumulated ignition ON time since the last reset. C/T Button 117 WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible personal injury or property damage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Compass Calibration NOTE: To ensure proper compass calibration, make sure the compass variance is properly set before manually calibrating the compass. If the compass appears erratic and the CAL symbol does not appear, you must manually put the compass into the “Calibration” mode. To Put Into a Calibration Mode Turn on the ignition and set the display to “Compass/ Temperature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press the RESET button approximately five seconds. The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED The HomeLinkt Universal Transceiver replaces up to three remote controls (hand held transmitters) that operate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button. The Universal Transceiver operates off your vehicle’s battery and charging system; no batteries are needed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Programming HomeLink NOTE: When programming a garage door opener, it is advised to park outside the garage. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio-frequency signal. 1. Press and hold the two outer HomeLink buttons, and release only when the indicator light begins to flash (after 20 seconds).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects. 2. Position the end of your hand-held transmitter 1-3 inches (3-8 cm) away from the HomeLink buttons while keeping the indicator light in view. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with (Programming( steps 6-8 to complete the programming of a rolling code equipped device (most commonly a garage door opener). 6. At the garage door opener receiver (motor-head unit) in the garage, locate the 9learn9 or 9smart9 button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 7.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you live in Canada or you are having difficulties programming a gate operator by using the 9Programming9 procedures (regardless of where you live), replace (Programming HomeLink( step 3 with the following: NOTE: If programming a garage door opener or gate operator, it is advised to unplug the device during the 9cycling9 process to prevent possible overheating. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Reprogramming a Single HomeLink Button To program a device to HomeLink using a HomeLink button previously trained, follow these steps: This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. Press and hold the desired HomeLink button. DO NOT release the button. • This device may not cause harmful interference. 2. The indicator light will begin to flash after 20 seconds.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS The auxiliary electrical outlet can provide power for in cab accessories designed for use with the standard “cigar lighter” plug. The outlet is located in the instrument panel below the ash receiver. A cap is attached to the outlet base indicating “Power Outlet” 12V-20A. There is an additional Power Outlet in the center console of a 40/20/40 seat (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 CIGAR LIGHTER AND ASH RECEIVER The ash receiver is opened and closed by pushing on the front surface of the receiver and then allowing the receiver to open. The cigar lighter is located above and to the left of the ash receiver. As a child safety precaution, the lighter only operates with the ignition switch ON. It heats when pushed in and pops out automatically when ready for use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS Front Instrument Panel Cupholders — Automatic Transmission Only Your new Ram truck is equipped with dual-opening adjustable cupholders. The cupholder is opened and closed by pushing on the front surface. Each opening in the cupholder is adjustable and will hold cups and mugs of various sizes. To secure the cup, place the cup to be held into one of the cup wells and then push the cupholder arm toward the cup until it is held stable.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE Center Storage Compartment — If Equipped 129 configure the storage area into compartments. For example, compartments can be configured to hold a lap-top computer, a cellular telephone, CD’s and miscellaneous items. The top of the cover provides a generous firm surface to serve as a desktop for your “mobile office.” WARNING! The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage and Seats — If Equipped Located in the center of the front 40/20/40 seat cushion there is a storage compartment. Standard cab models also have storage behind the seat. The Quad Cab models provide additional storage under the rear seat. Lift the seat to access the storage compartment. FOLD FLAT LOAD FLOOR — IF EQUIPPED Fold Flat Load Floor — If Equipped Quad Cab models with a 60/40 rear seat, may be equipped with a folding steel load floor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not operate the vehicle with loose items stored on the load floor. While driving or in an accident you may experience, abrupt stopping, rapid acceleration, or sharp turns. Loose objects stored on the load floor may move around with force and strike occupants, resulting in serious or fatal injury. 131 Unfolding the Load Floor 1. Lift the 60/40 seat cushion(s) to the upward position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. Positioning the Load Floor for Storage Access Under the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor. 3. Lift the load floor up to access storage under the load floor. WARNING! 3. Reverse the procedure to store the load floor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 PICKUP BOX 3 4. Reverse the procedure to put the load floor back in the secured down position before you operate the vehicle. The pickup box on your new Ram has many features designed for utility and convenience. NOTE: If you are installing a toolbox to the front of the pickup box, you must use Mopart toolbox brackets available from you dealer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE You can carry wide building materials (sheets of plywood, etc.) by building a raised load floor. Place lumber across the box in the indentations provided above the wheel housings and in the bulkhead dividers to form the floor. WARNING! The pickup box is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. WARNING! • Care should always be exercised when operating a vehicle with unrestrained cargo.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE There are stampings in the sheet metal on the inner side bulkheads of the box in front of and behind both wheel housings. Place wooden boards across the box from side to side to create separate load compartments in the pickup box. There are four tie-down cleats bolted to the lower sides of the pickup box that can sustain loads up to 1000 lbs (450 kg) total. SLIDE-IN CAMPERS Camper Applications Certain truck models are not recommended for slide-in campers.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Dual rear wheel pickup models require properly spaced rear clearance lights. If such a vehicle is operated without a tailgate, suitable lights must be installed. WARNING! To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the overhanging camper compartment and be free of leaks.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS m Instruments And Controls . . . . . . . . . . . . . . . . . 141 ▫ Electronic Volume Control . . . . . . . . . . . . . . . 152 m Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 142 ▫ Seek . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 m Instrument Cluster Description . . . . . . . . . . . . . 143 ▫ Tune . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 m Electronic Digital Clock . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Cassette Player Features . . . . . . . . . . . . . . . . 154 ▫ Tone Control . . . . . . . . . . . . . . . . . . . . . . . . 160 ▫ CD Changer Control Capability — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 ▫ AM/FM Selection . . . . . . . . . . . . . . . . . . . . . 161 ▫ Radio Display Messages . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Pinch Roller Release . . . . . . . . . . . . . . . . . . . 163 ▫ Noise Reduction . . . . . . . . . . . . . . . . . . . . . . 163 ▫ Operating Instructions — CD Player . . . . . . . . 164 ▫ Inserting The Compact Disc . . . . . . . . . . . . . . 164 ▫ Seek Button . . . . . . . . . . . . . . . . . . . . . . . . . 165 ▫ EJT CD (Eject) Button . . . . . . . . . . . . . . . . . . 165 139 ▫ CD Changer Control Capability — If Equipped . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL m Remote Sound System Controls — If Equipped . . 181 ▫ Heater Only — Fleet Vehicles . . . . . . . . . . . . . 185 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 182 ▫ Air Conditioning—If Equipped . . . . . . . . . . . 187 ▫ Tape Player . . . . . . . . . . . . . . . . . . . . . . . . . 182 ▫ Electric Rear Window Defroster And Heated Sideview Mirrors — If Equipped . . . . . . . . . . 191 ▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 141 INSTRUMENTS AND CONTROLS 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Malfunction Indicator Light This light is part of an onboard diagnostic system which monitors the emissions and engine control system. If the vehicle is ready for emissions testing the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started.
UNDERSTANDING YOUR INSTRUMENT PANEL 2. Voltage Gauge When the engine is running, the gauge indicates the electrical system voltage. The pointer should stay within the normal range if the battery is charged. If the pointer moves to either extreme left or right and remains there during normal driving, the electrical system should be serviced. NOTE: If the gauge pointer moves to either extreme of the gauge, the “Check Gages” indicator will illuminate and a single chime will sound. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 7. Seat Belt Reminder Light When the ignition switch is first turned ON, this light will turn on for 5 to 8 seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver seat belt remains unbuckled, the Seat Belt Warning Light will flash or remain on continuously.
UNDERSTANDING YOUR INSTRUMENT PANEL 12. Electronic Throttle Control (ETC) Light 5.7L Engines Only This light informs you of a problem with the Electronic Throttle Control system. If a problem is detected the light will come on while the engine is running. If the light remains lit with the engine running your vehicle will usually be drivable, however, see your dealer for service as soon as possible.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Do not leave your vehicle unattended with the engine running as you would not be able to react to the temperature indicator if the engine overheats. 14. Security The light will flash rapidly for approximately 16 seconds when the vehicle theft alarm is arming. The light will flash at a slower rate after the alarm is set. The security light will also come on for about two seconds when the ignition is first turned ON. 15.
UNDERSTANDING YOUR INSTRUMENT PANEL parking brake has not been released. This light will illuminate if the brake fluid is low, especially when braking or accelerating hard. This light will illuminate if the ABS indicator light has a malfunction. This light will flash if the engine is running and the parking brake is on. If the light remains on when the parking brake is released, it indicates a possible brake hydraulic system malfunction.
UNDERSTANDING YOUR INSTRUMENT PANEL The trip odometer shows individual trip mileage. To toggle between the odometer and the trip odometer, press the Odometer/Trip Odometer Button. To reset the Trip Odometer, press and hold the button while in trip mode, until the Trip Odometer resets. NOTE: There is also an engine hour function. This indicates the number of hours the engine has been running. To display the engine hours perform the following: Place the ignition in RUN, but do not start the engine.
UNDERSTANDING YOUR INSTRUMENT PANEL 24. Low Wash Light This light comes on when the washer fluid level falls below approximately 1/4 filled. The light will remain on until fluid is added and one minute has elapsed. 25. Odometer/Trip Odometer Button Press this button to toggle between the odometer and the trip odometer display. Holding the button in resets the trip odometer reading when in trip mode. 26. Fuel Gauge Shows level of fuel in tank when ignition switch is in the ON position. 27.
UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the “ON” or “ACC” position. 151 SALES CODE RBB—AM/FM STEREO RADIO WITH CASSETTE TAPE PLAYER AND CD CHANGER CAPABILITY When the ignition switch is in the “OFF” position, or when the radio frequency is being displayed, time keeping is accurately maintained. 4 Clock Setting Procedure 1.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: When first learning the control functions, the user should set the controls as shown in the following list. Tone Controls…As illustrated. Speaker Control…Centered. Power Button The volume control/power button pops out when pressed, this turns the sound system ON in the mode last used. Pushing the button back in turns the sound system OFF.
UNDERSTANDING YOUR INSTRUMENT PANEL To Set The Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. The symbol SET 1 will now show in the display window. Select the “1–5” button you wish to lock onto this station and press and release that button. If a button is not selected within 5 seconds after pressing the SET button, the station will continue to play but will not be locked into push-button memory.
UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received in the FM mode. Mode Button Press the MODE button to select between the cassette tape player, CD changer, or the Satellite Radio (if equipped). When the Satellite Radio (if equipped) is selected “SA” will appear in your radio display.
UNDERSTANDING YOUR INSTRUMENT PANEL Selective Music Search Press the SEEK button up or down to move the track number to skip forward or backward 1 to 7 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc. Fast Forward And Rewind Buttons Pressing the TUNE button up or down momentarily activates Fast Forward or Rewind and makes the directional arrows appear on the display. To stop Fast Forward or Rewind, press the TUNE button again.
UNDERSTANDING YOUR INSTRUMENT PANEL Mode Button To activate the CD changer, press the MODE button until CD information appears on the display. Push-Button While the CD changer is playing, press the NUMBER 1 push-button or the NUMBER 5 push-button to select a disc numbered higher or lower than the one currently being played. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display.
UNDERSTANDING YOUR INSTRUMENT PANEL 157 An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following reasons: • Excessive vibration • Disc inserted upside down • Damaged disc • Water condensation on optics Radio Display Messages Your radio has been designed to display certain messages when a problem is detected with the CD player.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER AND CD CHANGER CONTROLS — IF EQUIPPED Power Switch, Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. The volume will be displayed and continuously updated while the button is pressed. Seek Button (Radio Mode) Press and release the Seek button to search for the next station in either the AM or FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL PTY (Program Type) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off. Pressing the PTY button within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broadcast PTY information.
UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If no station is found with the selected PTY program type, the radio will return to the last preset station.
UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received. Scan Button Pressing the SCAN button causes the tuner to search for the next station, in either AM or FM, pausing for 5 seconds at each listenable station before continuing to the next. Pressing the AM/FM button continues the search in the alternate frequency band.
UNDERSTANDING YOUR INSTRUMENT PANEL To Change From Clock To Radio Mode Press the Time button to change the display between radio frequency and time. Operating Instructions — Tape Player Insert the cassette with the exposed tape side toward the right and the mechanical action of the player will gently pull the cassette into the play position. NOTE: When subjected to extremely cold temperatures, the tape mechanism may require a few minutes to warm up for proper operation.
UNDERSTANDING YOUR INSTRUMENT PANEL Tape Eject Press the EJT Tape button and the cassette will disengage and eject from the radio. Scan Button Press this button to play 10 seconds of each selection. Press the scan button a second time to cancel the feature. Changing Tape Direction If you wish to change the direction of tape travel (side being played), press the PTY button. The lighted arrow in the display window will show the new direction.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — CD Player NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. CAUTION! This CD player will accept 4 3⁄4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. Inserting The Compact Disc The CD player contained within the radio is not a multi-disc changer, and will only accept one CD.
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Button Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. EJT CD (Eject) Button Press this button and the disc will unload and move to the entrance for easy removal. The unit will switch to the radio mode.
UNDERSTANDING YOUR INSTRUMENT PANEL MODE Press the MODE button to select between the tape player, CD player, or satellite radio (if equipped). Time Button Press this button to change the display from elapsed CD playing time to time of day. To select Satellite Radio (if equipped), press the MODE button until the word SIRIUS appears. The following will be displayed in this order: After three seconds, the current channel name and number will be displayed for five seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL Push-Button While the CD changer is playing, press the NUMBER 1 push-button or the NUMBER 5 push-button to select a disc numbered higher or lower than the one currently being played. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display. 167 CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection.
UNDERSTANDING YOUR INSTRUMENT PANEL Balance The Balance control adjusts the left-to-right speaker balance. Press the BAL button in and it will pop out. Adjust the balance and push the button back in. Fade The Fade control provides for balance between the front and rear speakers. Press the FADE button in and it will pop out. Adjust the balance and push the button back in. Bass and Treble Tone Control The tone controls consist of 2 separate bands.
UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice.
UNDERSTANDING YOUR INSTRUMENT PANEL CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. Inserting The Compact Disc CAUTION! This CD player will accept 4 3⁄4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day.
UNDERSTANDING YOUR INSTRUMENT PANEL The disc can be ejected with the radio and ignition OFF. FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play. This feature plays the tracks on the selected disc in random order to provide an interesting change of pace.
UNDERSTANDING YOUR INSTRUMENT PANEL CD Changer Control Capability — If Equipped This radio is compatible with a remote mounted CD changer available through Mopar Accessories. The following instructions are for the radio controls that operate this CD changer. Mode Button To activate the CD changer, press the MODE button until CD information appears on the display.
UNDERSTANDING YOUR INSTRUMENT PANEL A CD HOT symbol indicates the player is too hot. CD HOT will pause the operation. Play can be resumed when the operating temperature is corrected or another MODE is selected.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RBQ—AM/FM STEREO RADIO WITH 6 - DISC CD CHANGER 175 NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio. Mode Press the MODE button repeatedly to select between AM, FM, the CD changer and Sirius Satellite Radio™ (if equipped). The display will show ST when a stereo station is received. Radio Operation Power/Volume Control Press the PWR/VOL control to turn the radio on.
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will bypass stations without stopping until you release it. Tune Press the TUNE control up or down to increase or decrease the frequency.
UNDERSTANDING YOUR INSTRUMENT PANEL 5 seconds after pressing the SET RND button, the station will continue to play but will not be locked into pushbutton memory. You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be locked into push-button memory.
UNDERSTANDING YOUR INSTRUMENT PANEL Inserting The Compact Disc CAUTION! This CD player will accept 4 3⁄4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day. If you insert a disc with the ignition OFF, the display will show the time of day for about 5 seconds, then go out.
UNDERSTANDING YOUR INSTRUMENT PANEL If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not removed, the radio will continue to play the non-removed CD. If the CD is removed and there are other CD’s in the radio, the radio will play the next CD. If the CD is removed and there are no other CD’s in the radio, the radio will return to the last selected AM or FM mode. The disc can be ejected with the radio and ignition OFF.
UNDERSTANDING YOUR INSTRUMENT PANEL PTY (Program Type) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off. Pressing the PTY button within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broadcast PTY information.
UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If no station is found with the selected PTY program type, the radio will return to the last station.
UNDERSTANDING YOUR INSTRUMENT PANEL increase the volume and pressing the bottom of the switch will decrease the volume. The center button of the right hand control will allow you to change the mode. The left hand control is a rocker type switch with a push button in the center. The function of the left hand control is different depending on which mode you are in. The following describes the left hand control operation in each mode.
UNDERSTANDING YOUR INSTRUMENT PANEL If you press the switch up or down twice it plays the second track, three times, it will play the third, etc. The button in the center of the left hand switch has no function in this mode. CASSETTE TAPE AND PLAYER MAINTENANCE To keep the cassette tapes and player in good condition, take the following precautions: 1. Do not use cassette tapes longer than C-90; otherwise, sound quality and tape durability will be greatly diminished. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL COMPACT DISC MAINTENANCE To keep the compact discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzene, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6.
UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS The controls for the heating and ventilation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desired interior conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are identified by the small dots. Panel Outside air flows through the outlets located in the instrument panel. Recirculation Modes (Panel or Bi-Level ) Select the recirculation modes when the outside air contains smoke or odors. This feature allows for recirculation of interior air only.
UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control 187 Air Conditioning—If Equipped The rotary knob at the center of the control panel controls the temperature of the interior air. You can choose your degree of comfort by rotating the knob. The coldest temperature setting is to the extreme left (blue region) and the warmest setting is to the extreme right (red region) of the rotation.
UNDERSTANDING YOUR INSTRUMENT PANEL snowflake button shows that the air conditioning is on. Press the button a second time to turn the air conditioning off. Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy.
UNDERSTANDING YOUR INSTRUMENT PANEL Floor 189 Blower Control Outside air flows primarily through the floor outlets located under the instrument panel. Mix Outside air flows in equal proportions through the floor and defroster outlets, and the air conditioning may be on.
UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control The rotary knob at the center of the control panel controls the temperature of the interior air. You can choose your degree of comfort by rotating the knob. The coldest temperature setting is to the extreme left (blue region) and the warmest setting is to the extreme right (red region) of the rotation. Circulation The cab is designed with features to promote outside air circulation. There are grilles in the cab back panel.
UNDERSTANDING YOUR INSTRUMENT PANEL Electric Rear Window Defroster and Heated Sideview Mirrors — If Equipped The Electric Rear Window Defroster and Heated side view mirrors are activated by pressing the heated grid button, located on the Climate Control panel, with the ignition On. Turning Off the ignition will deactivate the Electric Rear Window Defroster and Heated side view mirrors feature. These features also turn off after activation, when 15 minutes have elapsed.
UNDERSTANDING YOUR INSTRUMENT PANEL snowflake button shows that the air conditioning is on. Press the button a second time to turn the air conditioning off. A/C Pushbutton Air Conditioning Operation To turn on the Air Conditioning, set the fan control at any speed and press the snowflake button located on the control panel. Conditioned air will be directed through the outlets selected by the mode control.
UNDERSTANDING YOUR INSTRUMENT PANEL 193 Recirculation Pushbutton Pushing the Recirculation button allows interior air to recirculate continuously in any position except defrost and defrost/floor mode for rapid cool down of the interior. See “Fast Cooldown” later in this section. the major modes. These intermediate positions are identified by the small dots and give an even blend of both modes.
UNDERSTANDING YOUR INSTRUMENT PANEL Mix Blower Control Outside air flows in equal proportions through the floor and defroster outlets. Defrost Outside air is primarily directed to the windshield through the defroster outlets located at the base of the windshield and side window demist outlets. NOTE: The air conditioning compressor operates in both Mix and Defrost or a blend of these modes, even if the A/C button has not been pressed. This dehumidifies the air to help dry the windshield.
UNDERSTANDING YOUR INSTRUMENT PANEL Dual Zone Temperature Control Use this control to regulate the temperature of the air inside the passenger compartment. This is accomplished by having separate temperature control slides for both the driver and front passenger. The blue area of the scale indicates cooler temperatures while the red area indicates warmer temperatures.
UNDERSTANDING YOUR INSTRUMENT PANEL edges of the instrument panel. The demisters also provide extra air ducts for circulation. They are in operation whenever the Floor, Mix or Defrost modes are in use. NOTE: When you turn off the engine you may hear a hissing sound from under the hood for a short period of time. This is a normal condition that occurs if the air conditioning system has been on. It is not an indication of a problem with the air conditioning system.
UNDERSTANDING YOUR INSTRUMENT PANEL speeds will reduce fogging. Interior fogging on the windshield can be quickly removed by selecting the defrost mode. Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Chart
STARTING AND OPERATING CONTENTS m Ignition/Starter Switch . . . . . . . . . . . . . . . . . . . 204 ▫ Manual Transmission . . . . . . . . . . . . . . . . . . 205 ▫ Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 206 ▫ Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . . 206 ▫ On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING ▫ Manually Shifted Transfer Case Operating Information/Precautions . . . . . . . . . . . . . . . . 217 ▫ Rear Wheel Anti-Lock Brake System — RWAL . . . . . . . . . . . . . . . . . . . . . 231 ▫ Shifting Procedure - Manually Shifted Transfer Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219 ▫ Four-Wheel Anti-Lock Brake System — If Equipped . . . . . . . . . . . . . . . . . . 232 ▫ Transfer Case Reminder Light . . . . . . . . . . . . 220 m Power Steering .
STARTING AND OPERATING 201 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . . 248 ▫ Sulfur In Gasoline . . . . . . . . . . . . . . . . . . . . . 258 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . . 249 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . . 259 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . . 249 ▫ Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 259 ▫ Alignment And Balance . . . . . . . . . . . . . . . . .
STARTING AND OPERATING ▫ Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 265 ▫ Trailer Towing Mirrors — If Equipped . . . . . . 278 m Catalytic Converter . . . . . . . . . . . . . . . . . . . . . 266 ▫ Cooling System Tips — Trailer Towing . . . . . . 278 m Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . . . 267 ▫ Automatic Transmission Oil Temperature Warning Light . . . . . . . . . . . . . . . . . . . . . . . 279 ▫ Certification Label . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 203 m Recreational Towing — 4–Wheel Drive Vehicles (Behind Motorhome, Etc.) . . . . . . . . . . . . . . . . . 284 ▫ Returning To Normal Operation — Electronic Shift Transfer Case . . . . . . . . . . . . . . . . . . . . 289 ▫ Recreational Towing Procedure — Manual Shift Transfer Case — If Equipped . . . . . . . . . 285 m Driving Off-Road . . . . . . . . . . . . . . . . . . . . . . . 291 ▫ Returning To Normal Operation — Manual Shift Transfer Case . . . . . . . . . . . . . . . . .
STARTING AND OPERATING IGNITION/STARTER SWITCH NOTE: This vehicle is equipped with a transmission shift interlocking system. The brake pedal must be depressed to shift out of Park (P). OFF Unlocks the steering wheel (if equipped with locking wheel) and the automatic transmission shift control with engine off. ON This is the normal running position. LOCK Locks the automatic transmission shift control into the PARK position.
STARTING AND OPERATING 205 ACC Allows the electrical accessories to be used when the engine is not running. Key Reminder An alarm will sound to remind you if the key is left in the ignition and the driver’s door is opened. Manual Transmission Key Release Button STARTING PROCEDURES The starter should not be operated for more than 15second intervals. Waiting a few seconds between such intervals will protect the starter from overheating.
STARTING AND OPERATING Automatic Transmission Start the engine with the selector lever in NEUTRAL or PARK position. Apply the brake before shifting to any driving range. Normal Starting of either a warm or cold engine is obtained without pumping or depressing the accelerator pedal. Turn the key to the START position and release when the engine starts. If the engine fails to start within 10 seconds, turn the key to the OFF position, wait 5 seconds, then repeat the starting procedure.
STARTING AND OPERATING If the engine shows no sign of starting after two 15 second periods of cranking with the accelerator pedal held to the floor, the normal starting procedure should be repeated. 207 The engine block heater cord is routed under the hood to the right side of the vehicle and held to the body with removable clips. WARNING! WARNING! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle.
STARTING AND OPERATING CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust temperatures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. WARNING! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death.
STARTING AND OPERATING this range. Never use Park while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply parking brake first, then place the selector in Park position. On 4-wheel-drive vehicles be sure that the transfer case is in a drive position! WARNING! Never use Park position on an automatic transmission as a substitute for the parking brake.
STARTING AND OPERATING “R” Reverse Use this range only after the vehicle has come to a complete stop. “N” Neutral Shift to Neutral when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Set the parking brake if you must leave the vehicle. “D” Drive This position provides all forward gears, including 3rd gear direct and 4th or 5th (if equipped) gear overdrive (see Overdrive Operation). Use this range for most city and highway driving.
STARTING AND OPERATING Overdrive Operation The overdrive automatic transmission contains an electronically controlled fourth and fifth (if equipped) speed (Overdrive).
STARTING AND OPERATING When To Use “TOW/HAUL” Mode equipped) is disabled and 2-3 and 3-4 shift patterns are modified. Shifts into Overdrive (4th gear) are allowed during steady cruise (for improved fuel economy) and automatic closed-throttle downshifts to 3rd gear (for improved braking) will occur during steady braking. The “TOW/HAUL” light will illuminate in the instrument cluster to indicate when the switch has been activated. Pressing the switch a second time restores normal operation.
STARTING AND OPERATING high gear. When the vehicle speed drops or during acceleration when the transmission downshifts to second gear, the clutch automatically disengages. NOTE: The torque converter clutch will not engage until the transmission fluid and engine coolant are warm [usually after 1-3 miles (1.6 - 4.8 km) of driving]. Because the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting into Overdrive when cold. This is normal.
STARTING AND OPERATING Manual Transmission — 5–Speed (NV3500) 1500 models are equipped with the NV3500 manual transmission. Be sure the transmission is in 1st gear when starting from a standing position. Damage to the clutch can result from starting in 2nd or 3rd gear. Use each gear in numerical order – do not skip a gear. For most city driving you may find it easier to use only 1st through 4th gear ranges. For steady highway driving with light accelerations, 5th gear is recommended.
STARTING AND OPERATING Manual Transmission Shift Speeds in MPH (KPH) Engine Model Axle Mode 1 to 2 2 to 3 3 to 4 4 to 5 3.7L 1500 3.55 ACCEL 15 (24) 25 (40) 40 (65) 45 (72) & & 3.92 CRUISE 4.7L 1500 All ACCEL 15 (24) 25 (40) 40 (65) 45 (72) & CRUISE Manual Transmission – 5–Speed (NV4500) 2500 and 3500 models are equipped with the NV4500 manual transmission. This transmission has a “creeper” 1st gear which should be used to start from a standing position when carrying a payload or towing a trailer.
STARTING AND OPERATING Never drive with your foot resting on the clutch pedal, or attempt to hold the vehicle on a hill with the clutch pedal partially engaged, as this will cause abnormal wear on the clutch. Manual Transmission Shift Speeds To utilize your manual transmission efficiently for both fuel economy and performance, it should be upshifted as listed in the following chart. Shift at the vehicle speeds listed for acceleration.
STARTING AND OPERATING Manually Shifted Transfer Case Operating Information/Precautions The transfer case provides 4 mode positions - 2 (rear)wheel-drive high range, 4-wheel-drive high range, neutral, and 4-wheel-drive low range. This transfer case is intended to be driven in the 2-wheeldrive position (2H) for normal street and highway conditions such as dry hard surfaced roads.
STARTING AND OPERATING place. Shifting while only the front or rear wheels are spinning can cause damage to the transfer case. WARNING! Because 4-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road conditions permit. You or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake.
STARTING AND OPERATING 4H 4-Wheel-Drive High Range - Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only. 219 Shifting Procedure - Manually Shifted Transfer Case N Neutral - Disengages both the front and rear driveshafts from the powertrain. To be used for flat towing behind another vehicle. See Recreational Towing for more information. 4L 4-Wheel-Drive Low Range - Low speed 4-wheel-drive.
STARTING AND OPERATING vehicle in motion, the transfer case will engage / disengage faster if you momentarily release the accelerator pedal after completing the shift. Apply a constant force when shifting the transfer case lever. 2H or 4H ⇔ 4L With the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift an automatic transmission to N (Neutral) or depress the clutch on a manual transmission.
STARTING AND OPERATING Electronically Shifted Transfer Case Operating Information/Precautions This is an electric shift transfer case and is operated by the 4WD Control Switch (Transfer Case Switch), which is located on the instrument panel. The Electronically Shifted transfer case provides 4 mode positions: 2 (rear) wheel drive high range or all wheel drive high range, 4 wheel drive high range, 4 wheel drive low range, and neutral.
STARTING AND OPERATING Transfer Case Position Indicator Lights — Electronically Shifted Transfer Case Only Transfer case position indicator lights are located on the Four-Wheel-Drive Control Switch, found on your instrument panel, and indicate the current and desired transfer case selection. When you select a different transfer case position, the indicator lights will do the following: If All Shift Conditions are Met 1. The current position indicator light will turn OFF. 2.
STARTING AND OPERATING WARNING! Always engage the parking brake when powering down the vehicle if the (Service 4WD( light is illuminated. Not engaging the parking brake may allow the vehicle to roll which may cause personal injury. NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning. The transfer case is not equipped with a synchronizer and therefore the front and rear driveshaft speeds must be equal for the shift to take place.
STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position. The parking brake should always be applied when the driver is not in the vehicle.
STARTING AND OPERATING 225 Shifting Procedure - Electronically Shifted Transfer Case 5 NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift.The indicator light for the previous position will remain ON and the newly selected position indicator light will continue to flash until all the requirements for the selected position have been met.
STARTING AND OPERATING return the control knob back to the original position, make certain all shift requirements have been met, wait five (5) seconds and try the shift again. key must be in the ON position with the engine either RUNNING or OFF. This shift cannot be completed if the key is in the accessory position.
STARTING AND OPERATING Preferred Procedure 1. With engine RUNNING, slow vehicle to 2 to 3 mph (3 to 5 km/h). 2. Shift the transmission into NEUTRAL (depress clutch on manual transmissions). 3. While still rolling, rotate the transfer case control switch to the desired position. 4. After the desired position indicator light is ON (not flashing), shift transmission back into gear (release clutch on manual transmissions). Alternate Procedure 1. Bring the vehicle to complete stop. 2.
STARTING AND OPERATING LIMITED-SLIP DIFFERENTIAL — IF EQUIPPED The limited-slip differential provides additional traction on snow, ice, mud, sand and gravel, particularly when there is a difference between the traction characteristics of the surface under the right and left rear wheels. During normal driving and cornering, the limited-slip unit performs similarly to a conventional differential.
STARTING AND OPERATING 229 PARKING BRAKE The foot operated parking brake is positioned below the lower left corner of the instrument panel. To release the parking brake, pull the parking brake release handle. NOTE: The instrument cluster red brake warning light will come on and flash to indicate that the parking brake is applied. You must be sure that the parking brake is fully applied before leaving the vehicle.
STARTING AND OPERATING WARNING! • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury. Also be certain to leave an automatic transmission in Park, a manual transmission in Reverse or first gear. Failure to do so may allow the vehicle to roll and cause damage or injury. • Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be injured.
STARTING AND OPERATING 3500 Dual Rear Wheel Models Only The brake system power assist is provided by a hydroboost unit which shares fluid with the power steering system. You may experience some clicking or hissing noises from the hydro-boost system during hard braking conditions. NOTE: Under cold temperatures, pedal effort will be higher than normal until the power steering oil reaches operating temperature.
STARTING AND OPERATING WARNING! Both Anti-Lock Brake Systems contain sophisticated electronic equipment. It may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals.
STARTING AND OPERATING 233 WARNING! WARNING! Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
STARTING AND OPERATING POWER STEERING Your power steering system will provide mechanical steering capability if power assist is lost. TIRE SAFETY INFORMATION Tire Markings If for any reason the hydraulic pressure is interrupted, it will still be possible to steer your vehicle. Under these conditions you will experience a substantial increase in steering effort. NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards.
STARTING AND OPERATING 235 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter 9P9 is absent from this tire size designation. Example: 215/65R15 96H • Temporary Spare tires are high pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards (....blank....( = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING 237 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (ie. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure 239 Tire and Loading Information Placard Tire Placard Location NOTE: Some vehicles have a “Tire and Loading Information” placard located on the driver’s side “B” pillar. 5 This placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires.
STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
STARTING AND OPERATING 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 243 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. maximum loaded vehicle condition. These pressure conditions will be found in the “Supplemental Tire Pressure Information” section of this manual. 3.
STARTING AND OPERATING 245 check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are underinflated. Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. CAUTION! Tire pressures change by approximately 1 psi (7 kPa) per 12° F (7° C) of air temperature change.
STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high speed vehicle operation.
STARTING AND OPERATING Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Always use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels). Never combine them with other types of tires. Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
STARTING AND OPERATING Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 35 mph (55 km/h). Do not install more than one compact spare tire/wheel on the vehicle at any given time. See the paragraph on Freeing A Stuck Vehicle in Section 6 of this manual.
STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. 249 Many states have laws requiring tire replacement at this point.
STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. SUPPLEMENTAL TIRE PRESSURE INFORMATION A light load vehicle condition is defined as two passengers {150 lbs (68 kg) each} plus 200 lbs (91kg) of cargo.
STARTING AND OPERATING These cautions apply to all chain traction devices, including link and cable (radial) chains. Tire chain use is permitted only on the rear tires of Ram 4X2 trucks. NOTE: The use of class “S” chains is permitted on 1500 Ram Trucks with P245/70R17 tires only. NOTE: The use of class “U” chains is permitted on the front and rear of 4X4, 2500 Ram Trucks with LT245/ 70R17E tires.
STARTING AND OPERATING SNOW TIRES Snow tires should be of the same size and type construction as the front tires. Consult the manufacturer of the snow tire to determine any maximum vehicle speed requirement associated with the tire. These tires should always be operated at the vehicle maximum capacity inflation pressures under any load condition. While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires.
STARTING AND OPERATING Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed. NOTE: On Canadian vehicles only, if your Ram truck is equipped with All-Season type tires on the front and ON/OFF Road type tires mounted on the rear, do not use a front to back rotation pattern.
STARTING AND OPERATING Dual Rear Wheels 255 CAUTION! 3500 Dual Rear Tires have only one approved direction of rotation. This is to accommodate the asymmetrical design (tread pattern) of the ON/OFF road tire and the use of Outline White Letter (OWL) tires. The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires. The straight edge should touch all the tires.
STARTING AND OPERATING FUEL REQUIREMENTS All engines (except 5.7L engines) are designed to meet all emissions regulations and provide excellent fuel economy and performance when using high quality unleaded “regular” gasoline having an ocAll Engines tane rating of 87. The routine use of preExcept 5.7L mium gasoline is not recommended. Under normal conditions the use of premium fuel will not provide a benefit over high quality regular gasolines and in some circumstances may result in poorer performance.
STARTING AND OPERATING and durability for your vehicle. We recommend the use of gasolines that meet the WWFC specifications if they are available. Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasolines contain oxygenates, and are specifically blended to reduce vehicle emissions and improve air quality. We strongly support the use of reformulated gasolines.
STARTING AND OPERATING MMT In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasolines blended with MMT provide no performance advantage beyond gasolines of the same octane number without MMT. Gasolines blended with MMT reduce spark plug life and reduce emission system performance. We recommend that gasolines free of MMT be used in your vehicle.
STARTING AND OPERATING 259 CAUTION! CAUTION! If the Check Engine or Service Engine Soon light is flashing, immediate service is required; see onboard diagnostics system section. To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. Materials Added To Fuel All gasolines sold in the United States are required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in unnecessary cost.
STARTING AND OPERATING Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system.
STARTING AND OPERATING Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance, damage the emission control system, and could result in loss of warranty coverage. • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat.
STARTING AND OPERATING Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle.
STARTING AND OPERATING CAUTION! Only vehicles with the E-85 fuel filler door label can operate on E-85. ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame.
STARTING AND OPERATING NOTE: When the ambient temperature is above 90°F, you may experience hard starting and rough idle following start up even if the above recommendations are followed.
STARTING AND OPERATING Starting The characteristics of E-85 fuel make it unsuitable for use when ambient temperatures fall below 0°F. In the range of 0°F to 32°F, you may experience an increase in the time it takes for your engine to start, and a deterioration in drivability (sags and/or hesitations) until the engine is fully warmed up. Cruising Range Because E-85 fuel contains less energy per gallon than gasoline, you will experience an increase in fuel consumption.
STARTING AND OPERATING CATALYTIC CONVERTER The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, you must keep the engine maintained to assure proper operation and prevent possible damage.
STARTING AND OPERATING vehicle should be stopped, the engine shut off and the vehicle allowed to cool. Service, including a tune-up to manufacturer’s specifications should be obtained immediately. To minimize the possibility of catalyst damage: • Do not try to start the engine by pushing or towing the vehicle. • Do not idle the engine with any spark plug wires disconnected or removed. • Do not idle the engine for prolonged periods during very rough idle or malfunctioning operating conditions.
STARTING AND OPERATING rear axle systems (GAWR). Total load must be limited so GVWR and front and rear GAWR are not exceeded. Payload The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo. Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles. The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.
STARTING AND OPERATING 269 Loading The actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation. Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate. The entire vehicle should first be weighed on a commercial scale to insure that the GVWR has not been exceeded.
STARTING AND OPERATING NOTE: The weights shown in this chart are not necessarily the weights for your vehicle. Also, the amount of load added to both the front and rear axles can be computed after the vehicle has been weighed both in its (curb weight( condition, and in its (loaded and ready for operation( condition. Gross Vehicle Weight Rating (GVWR) 6500 LBS.
STARTING AND OPERATING include a 150 lb (68 kg) allowance for the presence of a driver.) Tongue Weight (of a trailer) is the weight placed on a vehicle’s trailer hitch by the trailer. GROSS TRAILER WEIGHT (GTW) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its 9loaded and ready for operation9 condition.
STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Certification label located at the driver’s door for the Gross Vehicle Weight Rating. CAUTION! When hauling cargo or towing a trailer, do not overload your vehicle or trailer.
STARTING AND OPERATING 2500/3500 Models • The Axles on 2500/3500 Models are trailer tow ready and DO NOT REQUIRE any special axle lubes or additives. Trailer Towing Recommendations • All trailer hitches should be professionally installed on your vehicle. • Safety chains must always be used between your vehicle and trailer. • Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury.
STARTING AND OPERATING • Be sure the trailer is loaded heavier in front, with 60% to 65% of the weight in front of the axle(s). Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents. (For a 95th Wheel9 style trailer, this range of loading on the 9King Pin9 should be between 15% and 25%.
STARTING AND OPERATING Connecting Trailer Lighting And Electric Trailer Brakes NOTE: A 4-way trailer tow connector, located behind the bumper, is standard equipment on all Ram pickup models. This connector contains the following vehicle circuits: park/tail lamps, left stop/turn lamp, right stop/ turn lamp, and ground. With the optional Trailer Tow Prep package a 7-way connector is also provided with the following additional circuits: backup lamp, trailer battery and electric brake.
STARTING AND OPERATING CAUTION! to 65% of the weight in the front of the trailer. This places 10% to 15% of the GTW on the tow hitch of your vehicle. Connect trailer lighting and brakes using factory harnesses only. Do not cut or splice wiring to the brake circuits. Use an approved wiring harness connector on the trailer. Trailer sway control and equalizing hitch are required for Class III or IV trailer hitches and tongue weights above 350 lbs (159 kg).
STARTING AND OPERATING Also, there are maximum tongue weight ratings that are not to be exceeded, as follows: • Class III (the bumper ball type) 500 lbs (227 kg) • Class IV (the receiver hitch type) 1200 lbs (544 kg) NOTE: When towing a trailer, the following requirements must be adhered to: • GCWR must not be exceeded • Total weight must be distributed between the tow vehicle and the trailer such that the following four (4) ratings are not exceeded: 1. GVWR 2. GTW 3.
STARTING AND OPERATING Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or outboard, the mirror head should be rotated (flipped Out or In). A small blindspot mirror is integrated onto the main mirror surface.
STARTING AND OPERATING • Air Conditioning— turn it off temporarily. • Hilly Terrain— Turn overdrive off. See Cooling System Operating information in the Service and Maintenance section of this manual for more information. Automatic Transmission Oil Temperature Warning Light All vehicles with automatic transmissions are equipped with a transmission sump oil temperature sensor and warning light.
STARTING AND OPERATING If your vehicle has an automatic transmission and you tow a trailer frequently, change transmission fluid and filter every 30,000 miles (48 000 km) SNOWPLOW Snowplow Prep Packages are available as a factory installed option. These packages include components necessary to equip your vehicle with a snowplow. Dodge Ram 1500 Models NOTE: Do not use Dodge Ram 1500 Models for snowplow applications.
STARTING AND OPERATING 2004 BODY BUILDER’S GUIDE. See your dealer, installer or snowplow manufacture for this information. There are unique electrical systems that must be connected to properly assure operator safety and prevent overloading vehicle systems that would void the vehicle warranty. WARNING! Attaching a snowplow to this vehicle could adversely affect performance of the airbag system in an accident.
STARTING AND OPERATING 2. The maximum number of occupants in the truck should not exceed two. 3. The total GVWR or the Front GAWR or the Rear GAWR should never be exceeded. 4. The snowplow prep packages are not available with the Sport Package. 5. Cargo capacity will be reduced by the addition of options or passengers, etc.
STARTING AND OPERATING conditions permit. Do not exceed 40 mph (64 km/h). The operator should always maintain a safe stopping distance and allow adequate passing clearance. Methods For Removing Snow 283 Operating Tips Under ideal snow plowing conditions, 20 mph (32 km/h) should be maximum operating speed. The operator should be familiar with the area and surface to be cleaned. Reduce speed and use extreme caution when plowing unfamiliar areas or under poor visibility.
STARTING AND OPERATING General Maintenance Snowplows should be maintained in accordance with the plow manufacturer’s instructions. Whenever the plow is disconnected from the vehicle, coat the exposed angling cylinder rods with chassis lubricant. The lift cylinder should be extended upward and chassis lubricant applied to the lift rod. The hydraulic hoses interconnect to keep the couplers clean. • Do not shift the transmission unless the engine has returned to idle and wheels have stopped.
STARTING AND OPERATING 285 for recreational towing. Refer below for the proper transfer case Neutral shifting procedure for your vehicle. 4. Shift automatic transmission to N (NEUTRAL), or depress the clutch on manual transmissions. Recreational Towing Procedure — Manual Shift Transfer Case — If Equipped Use the following procedure to prepare your vehicle for recreational towing: 5. Shift transfer case lever into N (NEUTRAL).
STARTING AND OPERATING CAUTION! Damage to the automatic transmission may occur if the transmission is shifted into P (PARK) with the transfer case in N (NEUTRAL) and the engine RUNNING. With the transfer case in N (NEUTRAL) ensure that the engine is OFF prior to shifting the transmission into P (PARK) Returning to Normal Operation — Manual Shift Transfer Case Use the following procedure to prepare your vehicle for normal usage: 1. Bring the vehicle to a complete stop. 2. Shut OFF the engine. 3.
STARTING AND OPERATING 287 CAUTION! CAUTION! • Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and damage the internal parts. It is necessary to follow these steps to be certain that the transfer case is fully in Neutral (N) before recreational towing to prevent damage to internal parts.
STARTING AND OPERATING 7. After shift is completed and the Neutral (N) light comes on release Neutral (N) button. 8. Start engine. 9. Shift automatic transmission into Reverse (R). 10. Release brake pedal for five seconds and ensure that there is no vehicle movement. 11. Repeat steps 9 and 10 with the transmission in Drive (D). 12. Shut engine OFF and place ignition key to the unlocked OFF position. 13. Shift automatic transmission into Park (P). 14. Apply parking brake. 15.
STARTING AND OPERATING 289 CAUTION! 5. Shift automatic transmission to Neutral (N) or depress clutch on manual transmission. Damage to the transmission may occur if the transmission is shifted into Park (P) with the transfer case in Neutral (N) and the engine RUNNING. With the transfer case in Neutral (N) ensure that the engine is OFF prior to shifting the transmission into Park (P). 6.
STARTING AND OPERATING during the 1 second time, then all of the mode position indicator lights will flash continuously until all requirements are met or until the Neutral (N) button is released. NOTE: The ignition key must be ON for a shift to take place and for the position indicator lights to be operable. If the key is not ON, the shift will not take place and no position indicator lights will be on or flashing.
STARTING AND OPERATING CAUTION! • Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and fluid loss will damage internal parts. DRIVING OFF-ROAD Care should be taken when attempting to climb steep hills or driving diagonally across a hill or slope.
STARTING AND OPERATING If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material. Impacted foreign material can cause a wheel imbalance. Removing the foreign material from the wheels will correct the situation. TRACTION When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface.
WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Lights . . . . . . . . . . . . . . . . . . 294 m Hoisting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312 m Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 295 m Jump-Starting . . . . . . . . . . . . . . . . . . . . . . . . . 312 m Jack Location . . . . . . . . . . . . . . . . . . . . . . . . . . 296 m Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . 316 ▫ Removal (All Models) . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING LIGHTS The Hazard Warning switch is mounted on the top of the steering column as shown in the illustration. will flash off and on to warn oncoming traffic of an emergency. Push the button a second time to turn off the flashers. This is an emergency warning system and should not be used when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists.
WHAT TO DO IN EMERGENCIES ADDING FUEL The fuel tank filler tube has a restricting door about 2 inches (50 mm) inside the opening. If using a portable fuel container, it should have a flexible nozzle long enough to force open the restricting door. WARNING! A fire may result if gasoline is pumped into a portable container that is in a vehicle or on a truck bed. You could be burned. Always place gas containers on the ground while filling.
WHAT TO DO IN EMERGENCIES JACK LOCATION Removal (All Models) The jack and jack tools are stored under the front passenger seat. Lift the flap on the side of the seat for access. Remove the jack and tools by removing the wing bolt and sliding the assembly from under the seat.
WHAT TO DO IN EMERGENCIES 297 WARNING! The jack is designed to use as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes, unless suitable supports are placed under the vehicle as a safety measure. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. WARNING! 2500/3500 Model Vehicles After using the jack and tools, always reinstall them in the original carrier and location.
WHAT TO DO IN EMERGENCIES Reinstalling The Scissors-Type Jack And Tools (1500 Models) 1. Lower the jack all the way down by turning the jack turn-screw until the jack is snug. 2. Position the jack and tool bag (unrolled). Make sure the lug wrench is under the jack near the jack turn-screw.
WHAT TO DO IN EMERGENCIES 299 3. Fold the flap and roll the jack tool kit into a cylindrical package (in direction of arrows), and tie to the jack using the tie straps.
WHAT TO DO IN EMERGENCIES Jack and Tools Tied Together 4. Place the jack and tools in the storage position holding the jack by the jack turn-screw, slip the jack and tools under seat so that the bottom slot engages into the fastener on the floor and then secure to the floor pan using the wing bolt.
WHAT TO DO IN EMERGENCIES 301 CHANGING A FLAT TIRE Removing The Spare Tire Remove the spare tire before attempting to jack the truck. Attach the wheel wrench to the jack extension tube. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube. Rotate the wheel wrench handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle.
WHAT TO DO IN EMERGENCIES Tire Changing Procedure WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. Do not raise this vehicle using a bumper jack.
WHAT TO DO IN EMERGENCIES • Turn on the Hazard Warning Flasher. • Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. • Passengers should not remain in the vehicle when the vehicle is being jacked.
WHAT TO DO IN EMERGENCIES 1. Remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. 3. Placement of the Jack: • For 1500 series trucks, when changing a front wheel, place the scissors jack under the rear portion of the lower control arm as shown below.
WHAT TO DO IN EMERGENCIES 305 6 1500 4X4 Jacking Location • For 2500/3500 4x2 series trucks, when changing a front wheel, place the bottle jack under the frame rail behind the wheel. Locate the jack as far forward as possible on the straight part of the frame. 2500/3500 4X2 Jacking Location • Operate the jack using the jack drive tube and the wheel wrench. The tube extension, may be used, but is not required.
WHAT TO DO IN EMERGENCIES Place the jack under the axle as close to the tire as possible with the drive tubes extending to the front. Connect the jack tube extension and wheel wrench. under the axle between the spring and the shock absorber with the drive tubes extending to the rear. Rear Jacking Location (All) 2500/3500 4X4 Jacking Location • For all trucks, when changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube.
WHAT TO DO IN EMERGENCIES NOTE: If the 2500/3500 bottle jack will not lower by turning the dial (thumb wheel) by hand, it may be necessary to use the jack drive tube in order to lower the jack. 4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface. WARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5.
WHAT TO DO IN EMERGENCIES WARNING! NOTE: Do not oil wheel studs. For chrome wheels, do not substitute with chrome plated wheel nuts. A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Always stow the jack parts and the extra tire and wheel in the places provided. Hub Caps The hub caps must be removed before raising the vehicle off the ground. 7. Install wheel center cap and remove wheel blocks.
WHAT TO DO IN EMERGENCIES 309 back and forth motion, loosen the wheel skin. Repeat this procedure around the tire until the skin pops off. Replace the wheel skins first using a rubber mallet. When replacing the hub caps, tilt the cap retainer over the lugnut bolt circle and strike the high side down with a rubber mallet. Be sure that the hub caps and wheel skins are firmly seated around the wheel. 8-Stud — Dual Rear Wheels Dual wheels are flat mounted, center piloted.
WHAT TO DO IN EMERGENCIES Dual wheel models require a special heavy-duty lug nut tightening adapter (included with the vehicle) to correctly tighten the lug nuts. Also, when it is necessary to remove and install dual rear wheels, use a proper vehicle lifting device. NOTE: When installing a spare tire as part of a dual rear wheel end combination, the tire diameter of the two individual tires must be compared. If there is a significant difference, the larger tire should be installed in a front location.
WHAT TO DO IN EMERGENCIES 1. Tighten the wheel nuts in the numbered sequence to a snug fit. 2. Retighten the wheel nuts in the same sequence to the torques listed in the table. Go through the sequence a second time to verify that specific torque has been achieved. Retighten to specifications at 100 miles (160 km) and after 500 miles (800 km). It is recommended that wheel stud nuts be kept torqued to specifications at all times. Torque wheel stud nuts to specifications at each lubrication interval.
WHAT TO DO IN EMERGENCIES Attach the wheel wrench to the extension tube. Rotate the winch mechanism until the wheel is drawn into place against the underside of the vehicle. Continue to rotate until you feel the winch mechanism slip or click 3 or 4 times. It cannot be overtightened. Push against the tire several times to be sure it is firmly in place. HOISTING A conventional floor jack may be used at the jacking locations, refer to the graphics that show jacking locations.
WHAT TO DO IN EMERGENCIES 313 WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush contaminated area immediately with large quantities of water. A battery generates hydrogen gas which is flammable and explosive. Keep flame or spark away from the vent holes.
WHAT TO DO IN EMERGENCIES both vehicles, place the automatic transmission in Park or the manual transmission in Neutral, and turn the ignition OFF. 3. Turn off the heater, radio, and all unnecessary electrical loads. 4. Connect one end of a jumper cable to the positive terminal of the booster battery. Connect the other end of the same cable to the positive terminal of the discharged battery.
WHAT TO DO IN EMERGENCIES 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. WARNING! • Do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. • During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze.
WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE If vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between DRIVE and REVERSE, while applying slight pressure to the accelerator. In general, the least amount of accelerator pedal pressure to maintain the rocking motion without spinning the wheels or racing the engine is most effective.
WHAT TO DO IN EMERGENCIES CAUTION! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. TOWING A DISABLED VEHICLE Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for the purpose, following equipment manufacturer’s instructions. Use of safety chains is mandatory.
WHAT TO DO IN EMERGENCIES If the vehicle is to be towed more than 15 miles (25 km) the vehicle must be towed with the rear wheels raised and the front wheels on the ground. It may also be towed on a flatbed or with the front wheels raised and the rear wheels on a dolly.
MAINTAINING YOUR VEHICLE CONTENTS m Engine Compartment— 3.7L/4.7L . . . . . . . . . . . 322 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 329 m Engine Compartment— 5.7L . . . . . . . . . . . . . . . 323 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . . 333 m Onboard Diagnostic System (OBD II) . . . . . . . . . 324 ▫ Drive Belts — Check Condition And Tensioner . . . . . . . . . . . . . . . . . . . . . . . . . . . 333 m Emissions Inspection And Maintenance Programs . . .
MAINTAINING YOUR VEHICLE ▫ Maintenance Free Battery . . . . . . . . . . . . . . . . 337 ▫ Clutch Hydraulic System . . . . . . . . . . . . . . . . 349 ▫ Air Conditioner Maintenance . . . . . . . . . . . . . 338 ▫ Clutch Linkage . . . . . . . . . . . . . . . . . . . . . . . 350 ▫ Power Steering — Fluid Check . . . . . . . . . . . . 339 ▫ Propeller Shaft Universal Joints . . . . . . . . . . . 350 ▫ Front Suspension Ball Joints . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . 361 m Fuse And Relay Center . . . . . . . . . . . . . . . . . . . 365 m Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . . 365 m Replacement Light Bulbs . . . . . . . . . . . . . . . . . 366 m Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 366 ▫ Headlight (Halogen)/Front Park And Turn Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT— 3.7L/4.
MAINTAINING YOUR VEHICLE 323 ENGINE COMPARTMENT— 5.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing. Normally, the OBD system will be ready. The OBD system may not be ready if your vehicle was recently serviced, if you recently had a dead battery, or a battery replacement.
MAINTAINING YOUR VEHICLE b. The MIL light will remain fully illuminated until the first engine crank or the key is turned off. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station. If your OBD system is not ready, you should see your dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update.
MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. REPLACEMENT PARTS Use of genuine Mopart parts for normal/scheduled maintenance and repairs is highly recommended to insure the designed performance.
MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. • The air conditioning system contains refrigerant under high pressure.
MAINTAINING YOUR VEHICLE 329 Engine Oil Checking Oil Level To assure proper lubrication of your vehicle’s engine, the engine oil must be maintained at the correct level. The best time to check the engine oil level is about 5 minutes after a fully warmed up engine is shut off or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings.
MAINTAINING YOUR VEHICLE • More than 50% of your driving is at sustained high speeds during hot weather, above 32°C (90°F) Change Engine Oil CAUTION! Overfilling or underfilling the crankcase will cause oil aeration or loss of oil pressure. This could damage your engine. Road conditions as well as your kind of driving affect the interval at which your oil should be changed. Check the following to determine if any apply to you: • Day or night temperatures are below 32°F (0°C). • Stop and go driving.
MAINTAINING YOUR VEHICLE Dusty Conditions Driving through dust-laden air increases the problems of keeping abrasive materials out of the engine. Under these conditions, special attention should be given to the engine air cleaner, the crankcase inlet air cleaner and the crankcase ventilation system. Make sure that these units are clean at all times. This will tend to reduce to a minimum the amount of abrasive material that may enter the engine.
MAINTAINING YOUR VEHICLE • SAE 5W-30 is the preferred oil for Dodge Trucks with 3.7L/4.7L/5.7L engines. • Lubricants which do not have both the engine oil certification mark or current service symbol and the correct viscosity grade number should not be used. Synthetic Engine Oils There are a number of engine oils being promoted as either synthetic or semi-synthetic. If you chose to use such a product, use only those oils that are API Certified and meet the SAE viscosity standard.
MAINTAINING YOUR VEHICLE governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Engine Oil Filter Selection The manufacturer’s engines have a full-flow type oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high quality filters should be used to assure most efficient service.
MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Under normal driving conditions, replace the air filter at the intervals shown on Schedule “A”. If, however, you drive the vehicle frequently under dusty or severe conditions, the filter element should be inspected periodically and replaced if necessary at the intervals shown on Schedule “B”. WARNING! The air induction system (air cleaner, hoses, etc) can provide a measure of protection in the case of engine backfire.
MAINTAINING YOUR VEHICLE Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.
MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may indicate severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE 337 plugged or sticking, replace with a new valve— do not attempt to clean the old PCV valve! Check the ventilation hoses for indications of damage, weepage or plugging with deposits. Replace if necessary. Maintenance Free Battery The top of the maintenance free battery is permanently sealed. You will never have to add water, nor is periodic maintenance required. To determine the battery charge, check the battery test indicator (if equipped) on top of the battery.
MAINTAINING YOUR VEHICLE WARNING! CAUTION! Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Battery gas is flammable and explosive. Keep flame or sparks away from the battery. Don’t use a booster battery or any other booster source with an output greater than 12 volts.
MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. • The air conditioning system contains refrigerant under high pressure.
MAINTAINING YOUR VEHICLE apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through a certified DaimlerChrysler Dealership.9 WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level.
MAINTAINING YOUR VEHICLE Steering Linkage — Inspection Whenever the vehicle is hoisted, all steering linkage joints should be inspected for evidence of damage. If seals are damaged, parts should be replaced to prevent leakage or contamination of the grease. Lubricate the steering linkage regularly according to the “Maintenance Schedule” in this manual. Half-shaft Constant Velocity Joints All four- wheel- drive 1500 models are equipped with four constant velocity joints.
MAINTAINING YOUR VEHICLE Windshield Wiper Blades The rubber edges of the wiper blades and the windshield should be cleaned periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield.
MAINTAINING YOUR VEHICLE directed on the container, aids cleaning action, reduces the freezing point to avoid line clogging, and is not harmful to paint or trim. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
MAINTAINING YOUR VEHICLE Cooling System Cooling System Maintenance At the intervals shown in the Maintenance Schedules Section of the manual, the system should be drained, flushed and filled. Inspection Coolant protection checks should be made every 12 months (prior to the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant as specified. Inspect the entire cooling system for leaks.
MAINTAINING YOUR VEHICLE The radiator normally remains completely full, so there is no longer a need to remove the coolant pressure cap except for checking coolant freeze point or replacement with new antifreeze coolant. WARNING! Never add coolant to the radiator when the engine is overheated. Do not loosen or remove pressure cap to cool an overheated engine! The coolant is under pressure and severe scalding could result.
MAINTAINING YOUR VEHICLE When additional coolant is needed to maintain the proper level, add the recommended concentration of antifreeze and water to the coolant bottle. Do not overfill. NOTE: Failure to follow the antifreeze concentration and replacement recommendations, or failure to use antifreeze formulated to prevent corrosion of all cooling system metals, may result in radiator plugging, overheating, or cooling system leaks such as in core hole plugs.
MAINTAINING YOUR VEHICLE Disposal Of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. Do not store ethylene glycol-based engine coolant in open containers or allow it to remain in puddles on the ground. Prevent ingestion by animals and children. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately.
MAINTAINING YOUR VEHICLE Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present. Components should be replaced immediately if there is any evidence of wear or damage that could cause failure.
MAINTAINING YOUR VEHICLE 349 WARNING! CAUTION! Use of a brake fluid that may have a lower initial boiling point, or is unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident. Do not allow a petroleum-base fluid to contaminate the brake fluid. Seal damage may result. WARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire.
MAINTAINING YOUR VEHICLE Clutch Linkage If the clutch pedal linkage begins to squeak or grunt, the clutch pedal pivot bushings should be lubricated. Refer to Recommended Fluids, Lubricants and Genuine Parts for the correct lubricant type. This inspection should be made with the vehicle in a level position. The fluid level should be even with the bottom of the fill hole for the Manufacturer’s C205F HD Front Axles. The fluid level should be 5/8” (16 mm) below on 9 1/4” Manufacturer’s Rear Axles.
MAINTAINING YOUR VEHICLE NOTE: The presence of water in the gear lubricant will result in corrosion and possible failure of differential components. Operation of the vehicle in water, as may be encountered in some off-highway types of service, will require draining and refilling the axle to avoid damage. Limited-Slip Differentials in 1500 Model vehicles require that 4 oz. (118 ml) Mopart limited slip additive be added to the gear lubricant.
MAINTAINING YOUR VEHICLE Lubricant Selection NV-3500 (5-Speed Manual Transmission — If Equipped) This transmission is filled with manual transmission fluid at the factory. This fluid does not require periodic changing. If it is necessary to add or change fluid in this transmission refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. This is the only lubricant recommended for use in the NV-3500 transmission.
MAINTAINING YOUR VEHICLE To check the automatic transmission fluid level properly, the following procedure must be used: 1. Operate the engine at idle speed and normal operating temperature. 2. The vehicle must be on level ground. 3. Fully apply the parking brake and press the brake pedal. 4. Place the gear selector momentarily in each gear position ending with the lever in P (Park). 5. Remove the dipstick, wipe it clean and reinsert it until seated. 6.
MAINTAINING YOUR VEHICLE CAUTION! Be aware that if the fluid temperature is below 50°F (10°C) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. Selection Of Lubricant Refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid. CAUTION! 7. Check for leaks. Release parking brake.
MAINTAINING YOUR VEHICLE Automatic Transmission Fluid and Filter Change To obtain best performance and long life for automatic transmissions, the manufacturer recommends that they be given regular maintenance service by an Authorized Dodge Dealer or Service Center. It is important that proper lubricant is used in the transmission. Refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. The fluid and filter(s) should be changed as specified in the Maintenance Schedule (Section 8).
MAINTAINING YOUR VEHICLE Selection of Lubricating Grease The National Lubricating Grease Institute (NLGI) has developed a symbol (Certification Mark) to aid the vehicle owner in the proper selection of grease for the lubrication of wheel bearings and chassis components. This symbol (an example is shown below) is located on the grease container and identifies the application and quality of the grease.
MAINTAINING YOUR VEHICLE 357 or suspected. Proper maintenance of the entire vehicle will help the effectiveness of the noise control systems. Air Cleaner Assembly Inspect air cleaner housing for proper assembly and fit. Make certain that the air cleaner is properly positioned and the cover is tight. Check all hoses leading to the cleaner for tightness. The gasket between the air cleaner housing and throttle body must be intact and in good condition.
MAINTAINING YOUR VEHICLE control prior to its sale or delivery to the ultimate purchaser or while it is in use, or (2) the use of the vehicle after such device or element of design has been removed or rendered inoperative by any person. ENGINE COOLING SYSTEM Among those acts presumed to constitute tampering are the acts listed below.
MAINTAINING YOUR VEHICLE 359 Noise Systems Maintenance Chart and Service Log Insert Month, Day, Year under column mileage closest to the mileage at which service was performed.
MAINTAINING YOUR VEHICLE Noise Systems Maintenance Chart and Service Log Insert Month, Day, Year under column mileage closest to the mileage at which service was performed.
MAINTAINING YOUR VEHICLE Appearance Care and Protection from Corrosion The most common causes are: Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
MAINTAINING YOUR VEHICLE • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.
MAINTAINING YOUR VEHICLE • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use Mopart touch up paint on scratches as soon as possible. Your dealer has touch up paint to match the color of your vehicle. Interior Care Use Mopart Fabric Cleaner to clean fabric upholstery and carpeting.
MAINTAINING YOUR VEHICLE Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters or windshields equipped with a windshield wiper de-icer. Do not use scrapers or other sharp instruments which may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using.
MAINTAINING YOUR VEHICLE FUSE AND RELAY CENTER 365 2. Use specified fuses only. 3. Always properly reinstall the cover. VEHICLE STORAGE If you are storing your vehicle for more than 21 days, we recommend that you take the following steps to minimize the drain on your vehicle’s battery: • Disconnect the Ignition-Off Draw fuse (I.O.D.) fuse located in the Fuse and Relay Center, located in the engine compartment. The I.O.D.
MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS BULB REPLACEMENT LIGHT BULBS — Inside Bulb No. Overhead Console Lights . . . . . . . . . . . . . . . TS 212-2 Dome Light. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7679 Headlight (Halogen)/Front Park and Turn Lights All of the inside bulbs are brass or glass wedge base. Aluminum base bulbs are not approved. LIGHT BULBS — Outside Bulb No. Back-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 367 7
MAINTAINING YOUR VEHICLE 2. Remove the three (3) bolts from the headlight housing. NOTE: The lower bolt on the driver side headlight also retains the ambient temperature sensor between the headlight assembly and the frame.
MAINTAINING YOUR VEHICLE 3. Pull the housing out from the fender to allow room to disconnect the electrical connectors. 369 4. Unlock and pull connector straight from the base of the headlight halogen bulb. 5. Twist connector on turn signal/park light bulb 1⁄4 turn and remove connector and bulb from housing. 6. Remove housing from vehicle with headlight halogen bulb in housing.
MAINTAINING YOUR VEHICLE 7. Twist collar on headlight halogen bulb 1⁄4 turn and remove headlight bulb from the housing. 8. Replace headlight or turn signal bulb. Do not touch the headlight halogen bulb. 9. Reverse procedure for installation of bulbs and housing. 10. Tighten the outboard fastener first. Tail, Stop, Turn and Backup Lights 1. Remove the two (2) screws that pass through the bed sheetmetal. 2.
MAINTAINING YOUR VEHICLE 371 4. Remove the four (4) screws from the bulb strip in the housing. 3. Push the red lock slide in on the connector and remove the housing from the vehicle.
MAINTAINING YOUR VEHICLE 5. Pull the appropriate bulb straight from the bulb strip. 7. While holding the taillight firmly in place, fasten the top screw first. Center High-Mounted Stoplight With Cargo Light 1. Remove the two (2) screws holding the housing/lens to the body as shown. • Top Bulb: Park/Turn/Hazard • Center Bulb: Stop/Park/Sidemarker • Bottom Bulb: Backup Lights 6. Reverse procedure for installation of bulbs and housing.
MAINTAINING YOUR VEHICLE 373 2. Separate the connector holding the housing and wiring harness to the body. • Outside Bulbs: Cargo Lamps 3. Turn desired bulb socket 1⁄4 turn and remove socket and bulb from housing. 4. Pull desired bulb straight from the socket. • Inside Bulb: Center High Mount Stop Lamp 5. Reverse procedure for installation of bulbs and housing.
MAINTAINING YOUR VEHICLE Cab Top Clearance Lights — If Equipped 1. Remove the two screws from the top of the light. 2. Rotate the socket 1⁄4 turn and pull it from the light assembly.
MAINTAINING YOUR VEHICLE 3. Pull the bulb straight from it’s socket and replace. 375 Tailgate ID Lights (Dual Rear Wheels) 1. Remove the two screws and housing and access the bulb sockets from the rear.
MAINTAINING YOUR VEHICLE 2. Turn socket 1⁄4 turn counterclockwise to access the bulb. 3. Pull bulb straight out from socket. 4. Reverse procedure for installation of bulbs and housing.
MAINTAINING YOUR VEHICLE Side Marker Lights (Dual Rear Wheels) 377 3. Turn socket 1⁄4 turn counterclockwise and remove from assembly to access the bulb. 4. Pull bulb straight out from socket. 5. Reverse procedure for installation of bulbs and housing. 1. Push rearward on the side marker light assembly. 2. Pull the entire assembly from the fender.
MAINTAINING YOUR VEHICLE Fog Lights 2. Pull bulb straight from the connector. 1. Reach under the vehicle, unlock and twist connector counterclockwise 1⁄4 turn and remove connector and bulb from housing. 3. Reverse procedure for installation of bulbs and housing.
MAINTAINING YOUR VEHICLE 379 FLUIDS AND CAPACITIES U.S. Metric Fuel 3.7L/4.7L, 87 Octane 5.7L, 89 Octane 1500 Shortbed Models 1500 Longbed Models 2500 Shortbed Models 2500 Longbed Models 3500 Shortbed Models 3500 Longbed Models Engine Oil (with filter) 3.7L Engine V-6, SAE 5W-30, API Certified 4.7L Engine V-8, SAE 5W-30, API Certified 5.7L Engine V-8, SAE 5W-30, API Certified 26 35 34 35 34 35 gal. gal. gal. gal. gal. gal. 98L 132L 128L 132L 128L 132L 5.0 qts. 6.0 qts. 7.0 qts. 4.7L 5.7L 6.
MAINTAINING YOUR VEHICLE Cooling System 3.7L (Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula) 4.7L (Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula) 5.7L (Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula) U.S. Metric 17 qts. 16L 17 qts. 16L 18.7 qts. 17.
MAINTAINING YOUR VEHICLE 381 RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection (all except 5.7L) Fuel Selection (5.7L) Fluids, Lubricants and Genuine Parts Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) P/N 5011764AB or equivalent. Use SAE 5W-30, API Certified, meeting material standard MS-6395. Refer to oil viscosity chart for alternative grade.
MAINTAINING YOUR VEHICLE Chassis Component Fluids, Lubricants and Genuine Parts. Automatic Transmission Mopart ATF+4, Automatic Transmission Fluid Transfer Case Mopart ATF+4, Automatic Transmission Fluid Manual Transmission Fluid NV 3500 Mopart “Manual Transmission Fluid” P/N 4874464. Manual Transmission Fluid NV 4500 75W-85 Synthetic, API grade GL4, Mopart P/N 4874459. Clutch Linkage Multipurpose Grease, NLGI Grade 2 E.P.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E m Emission Control System Maintenance . . . . . . . . 384 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 387 m Maintenance Schedules . . . . . . . . . . . . . . . . . . . 384 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 384 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type in this section (Section 8) must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and S reliability.
MAINTENANCE SCHEDULES • Heavy Loading. • Taxi, police, or delivery service (commercial service). • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the 9Maintenance Schedules9 section of this manual. NOTE: Most vehicles are operated under the conditions listed for Schedule 9B9. Second is Schedule “A”.
M 386 MAINTENANCE SCHEDULES A I At Each Stop for Fuel N T • Check the engine oil level about 5 minutes after a fully E warmed engine is shut off. Checking the oil level while N A the vehicle is on level ground will improve the accuN racy of the oil level reading. Add oil only when the C level is at or below the ADD or MIN mark. E S C H E D U L E S 8 • Check the windshield washer solvent and add if required. Once a Month • Check tire pressure and look for unusual wear or damage.
SCHEDULE “B” Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90° F C (32°). • Trailer towing. • Snowplowing.
M 388 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Lubricate outer tie rod ends 2500/3500 (4X4) modN C els only. E Change rear axle fluid. S C H E D U L E S 8 Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Lubricate outer tie rod ends 2500/3500 (4X4) models only. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary. Drain and refill automatic tranmission fluid and change main sump filter (45RFE/545RFE only).
M 390 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Lubricate outer tie rod ends 2500/3500 (4X4) modN C els only. E Change rear axle fluid. S C H E D U L E S 8 Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Lubricate outer tie rod ends 2500/3500 (4X4) models only. Drain and refill transfer case fluid (4X4). Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Replace ignition cables. Inspect PCV valve, replace as necessary. Drain and refill automatic tranmission fluid and change main sump filter (45RFE/545RFE only).
M 392 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Lubricate outer tie rod ends 2500/3500 (4X4) modN C els only. E Inspect engine air cleaner filter. S C H E D U L E S 8 Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect auto tension drive belt and replace if required. (3.7L/4.7L/5.7L).
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Lubricate outer tie rod ends 2500/3500 (4X4) models only. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary. Inspect auto tension drive belt and replace if required (3.7L/4.7L/5.7L).
M 394 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Lubricate outer tie rod ends 2500/3500 (4X4) modN C els only. E Flush and replace engine coolant. S C H E D U L E S 8 Flush and replace Power Steering Fluid. Inspect brake linings.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Lubricate outer tie rod ends 2500/3500 (4X4) models only. Drain and refill transfer case fluid (4X4). Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Replace ignition cables. Inspect PCV valve, replace as necessary. Inspect auto tension drive belt and replace if required (3.7L/4.7L/5.7L).
M 396 SCHEDULE “B” A I 105,000 108,000 111,000 114,000 117,000 120,000 N Miles T (Kilometers) (168 000) (173 000) (178 000) (182 000) (187 000) (192 000) E X N Drain and refill automatic tranmission fluid A and change main sump filter (45RFE/545RFE N only). C E * This maintenance is recommended by the manufacture Inspection and service should also be performed anytime S C H E D U L E S 8 to the owner but is not required to maintain the emissions warranty.
SCHEDULE “A” 397 M Schedule “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Check transfer case fluid level (4X4). Lubricate outer tie rod ends 2500/3500 (4X4) models only. Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs.
M 398 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Check transfer case fluid level (4X4). E Lubricate outer tie rod ends 2500/3500 (4X4) S C H E D U L E S 8 models only. Flush and replace engine coolant at 60 months, regardless of mileage. Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. Inspect PCV valve, replace as necessary. Replace ignition cables.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Lubricate outer tie rod ends 2500/3500 (4X4) models only. Check transfer case fluid level (4X4). Flush and replace Power Steering Fluid. Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. Inspect PCV valve, replace as necessary. Inspect auto tension drive belt and replace if required (3.7L/4.7L/5.7L).
M 400 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Drain and refill transfer case fluid (4X4). E Flush and replace engine coolant, if not done at 60 mos. S C H E D U L E S 8 Lubricate outer tie rod ends 2500/3500 (4X4) models only. Inspect brake linings. Inspect auto tension drive belt and replace if required (3.7L/4.7L/5.7L). Replace ignition cables. Replace engine air cleaner filter. Replace spark plugs.
SCHEDULE “A” WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404 ▫ Prepare For The Appointment . . . . . . . . . . . . 404 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 404 ▫ Be Reasonable With Requests . . . . . . . . . . . . . 404 m If You Need Assistance . . . . . . . . . . . . . . . . . . . 404 m Warranty Information . . . . . . . . . . . . . . . . . . . . 407 m Mopart Parts . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE The manufacturer has empowered its dealers to make warranty and repair decisions that ensure you are not inconvenienced. There is no need for you to wait for a decision from the manufacturer. If a special circumstance occurs that requires information from the manufacturer, we have asked the dealer’s service management to make the contact on your behalf. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process.
IF YOU NEED CONSUMER ASSISTANCE In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico (915) 729–1248 or 729–1240 Outside Mexico (525) 729–1248 or 729–1240 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center.
IF YOU NEED CONSUMER ASSISTANCE Contract, and you require service after your manufacturer’s new vehicle limited warranty expires, please refer to your contract documents, and contact the person listed in those documents. We appreciate that you have made a major investment when you purchased your new vehicle. Your dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with your ownership experience.
IF YOU NEED CONSUMER ASSISTANCE
IF YOU NEED CONSUMER ASSISTANCE MOPART PARTS Mopart fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.
IF YOU NEED CONSUMER ASSISTANCE 411 Call Toll Free at 1–800–890–4038 (U.S.) or 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: www.techauthority.daimlerchrysler.com or www.daimlerchrysler.
INDEX 10
INDEX Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . 259,295 Air Cleaner, Engine . . . . . . . . . . . . . . . . . . . 334,357 Air Conditioner Maintenance . . . . . . . . . . . . 327,338 Air Conditioning Refrigerant . . . . . . . 327,328,338,339 Air Conditioning System . . . . . . . . . . . . . 187,327,338 Air Conditioning System, Zone Control . . . . . . . . 191 Air Pressure, Tires . . . . . . . . . . . . . . . . . . . . 244,251 Airbag . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX B-Pillar Location . . . . . . . . . . . . . . . . . . . . . . . . 239 Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382 Brake System . . . . . . . . . . . . . . . . . . . . . . . . 230,348 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . 231,232 Disc Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . 348 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . 348 Parking . . . . . . .
INDEX Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . 185 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349 Clutch Linkage Maintenance . . . . . . . . . . . . . . . . 350 Compact Disc Maintenance . . . . . . . . . . . . . . . . . 184 Compact Disc Player . . . . . . . . . . . . . . . . . . 158,164 Compact Spare Tire . . . . . . . . . . . . . . . . . . . . . . 247 Compass . . . . . . . . .
INDEX Disposal Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 347 Door Ajar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Door Opener, Garage . . . . . . . . . . . . . . . . . . . . . 120 Drive Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333 Drive Shaft Universal Joints . . . . . . . . . . . . . . . . 341 Dual Rear Wheels . . . . . . . . . . . . . . . . . . . . . 255,309 E-85 Fuel . .
INDEX Exhaust System . . . . . . . . . . . . . . . . . . . . . . . 69,343 Exterior Lighting . . . . . . . . . . . . . . . . . . . . . . . . 101 Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . 334,357 Engine Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 334 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . 333,381 Engine Oil Disposal . . . . . . . . . . . . . . . . . . . . 332 Flashers Turn Signal . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Fuel, Flexible . . . . . . . . . . . . . See Flexible Fuel Vehicles Fueling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259 Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365 Garage Door Opener . . . . . . . . . . . . . . . . . . . . . 120 Gas Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260 Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . 257 Gauges . . . .
INDEX Hub Caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308 Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14,204 Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11,14 Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . 55,56 Inflation Pressure Tires . . . . . . . . . . . . . . . . . . . . 251 Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . .
INDEX Courtesy/Reading . . . . . . . . . . . . . . . . . . . . . 113 Cruise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 Daytime Running . . . . . . . . . . . . . . . . . . . . . . 102 Dual Wheel Assembly Rear . . . . . . . . . . . . . . . 375 Fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102,378 Four-Wheel Drive Indicator . . . . . . . . . . . . . . . 220 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 294 Headlights . . . . . . . . . . . . . . . . . . . . . . .
INDEX Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . . . 94 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 327 Maintenance Free Battery . . . . . . . . . . . . . . . . . . 337 Maintenance Procedures . . . . . . . . . . . . . . . . . . . 327 Maintenance Schedule . . . . . . . . . . . . . . . . . . . . 384 Schedule 9A9 . . . . . . . . . . . . . . . . . . . . . . . . . 397 Schedule 9B9 . . . . . . . . . . . . . . . . . . . . . . . . . . 387 Malfunction Indicator Light . .
INDEX Dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333,381 Filter Disposal . . . . . . . . . . . . . . . . . . . . . . . . 332 Identification Logo . . . . . . . . . . . . . . . . . . . . . 331 Materials Added to . . . . . . . . . . . . . . . . . . . . . 332 Pressure Gauge . . . . . . . . . . . . . . . . . . . . . . . 145 Recommendation . . . . . . . .
INDEX Pretensioners Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Programmable Electronic Features . . . . . . . . . 121,125 Programming Transmitters . . . . . . . . . . . . . . 121,125 Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . . 247 Radiator Cap . . . . . . . . . . . . . . . . . . . . . . . . 344,347 Radio . . . . . . . . . . . . . . . . . . . . . . . . 151,158,168,175 Radio Operation . . . . . . . . . . . . . . . . . . . . . .
INDEX Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . 33,34,70 Adjustable Upper Shoulder Anchorage . . . . . . . . 41 And Pregnant Women . . . . . . . . . . . . . . . . . . . 44 Child Restraint . . . . . . . . . . . . . . . . . . . . . . . 55,67 Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Front Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Reminder . . . . . . . . . . . . . . . .
INDEX Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333 Speed Control . . . . . . . . . . . . . . . . . . . . . . . . . . 109 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 Automatic Transmission . . . . . . . . . . . . . . . . . 206 Engine Block Heater . . . . . . . . . . . . . . . . . . . . 207 Engine Fails to Start . . . . . . . . . . . . . . . . . . . . 206 Manual Transmission .
INDEX Inflation Pressures . . . . . . . . . . . . . . . . . . . . . 244 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302 Load Capacity . . . . . . . . . . . . . . . . . . . . . 239,240 Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 249 Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . 253,386 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 234,243 Sizes . . . . . . . . . . . .
INDEX Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 Transmitter, Garage Door Opener . . . . . . . . . . . . 120 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . 249 Trip Computer . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Trip Odometer . . . . . . . . . . . . . . . . . . . . . . . 148,150 Turn Signals . . . . . . . . . . . . . . . . . . . 103,144,366,370 Underhood Fuses . . . . . . . . . . . . . . . . . . . . . . . . 365 Universal Transmitter . . . .
INDEX Wiper Blade Replacement . . . . . . . . . . . . . . . . . . 342 429 Wipers, Intermittent . . . . . . . . . . . . . . . . . . . . . .