TABLE OF CONTENTS SECTION PAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1 1 INTRODUCTION 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4 INSTRUMENT PANEL AND CONTROLS 5 STARTING AND OPERATING 6 WHAT TO DO IN EMERGENCIES 7 MAINTAINING YOUR VEHICLE 8 MAINTENANCE SCHEDULES 9 IF YOU NEED CONSUMER ASSISTANCE 10 INDEX . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS m Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m Vehicle Identification Number . . . . . . . . . . . . . . . 5 m How To Use This Manual . . . . . . . . . . . . . . . . . . 4 m Vehicle Modifications / Alterations . . . . . . . . . . . 6 m Warnings And Cautions . . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . . . 9 ▫ Power Door Locks . . . . . . . . . . . . . . . . . . . . .14 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . . 9 ▫ Child Protection Door Lock . . . . . . . . . . . . . . .17 ▫ Sentry Key — If Equipped . . . . . . . . . . . . . . . . 9 m Remote Keyless Entry . . . . . . . . . . . . . . . . . . . . .19 m Ignition And Steering Lock . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE m Security Alarm System — If Equipped . . . . . . . . .24 ▫ To Set The Alarm . . . . . . . . . . . . . . . . . . . . . .25 ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .25 m Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 m Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 ▫ Power Windows . . . . . . . . . . . . . . . . . . . . . . .27 ▫ Auto Down . . . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to order duplicate keys from your dealer or a locksmith. If you received your keys without the bag, ask your dealer to give you the number. NOTE: Integrated keys (key and key fob combined) must be cut by the dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE on the remaining transmitters will work. If the vehicle is shifted out of PARK, all the transmitter buttons are disabled for all keys. NOTE: The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and a loss of security protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed and needs to be cut. NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer. Customer Key Programming You can program new keys to the system if you have two valid keys by doing the following: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IGNITION AND STEERING LOCK In the LOCK position, the steering and ignition systems are locked to provide anti-theft protection for your vehicle. It may be difficult to turn the key from the LOCK position when starting your vehicle, if the steering wheel is locked.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: The steering wheel will lock when the key is removed, and the steering wheel is turned around 115 degrees clockwise or 65 degrees counterclockwise from the center position. The interior lights will remain on for 30 seconds after the last door is closed, or until all doors are closed and either the ignition is turned to the ON position or a key fob LOCK button is pressed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. WARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 • The driver’s door is open while the key is in the ignition. Automatic Door Locks If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedure: 1. Enter your vehicle and Close all doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Within 10 seconds, cycle the key from the OFF position to the ON position four times; ending in the ON position ( Do not start the engine ). • The Automatic Door Lock feature must be enabled. 5. Within 30 seconds, press the driver’s door lock switch in the LOCK direction. • The vehicle is in P (Park) and the ignition switch is in the Off position. 6. A single chime will be heard to indicate the feature has been disabled. 7.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may be confusing during this programming procedure). 3. Insert the key into the ignition. 4. Within 10 seconds, cycle the key from the OFF position to the ON position four times ending in the ON position (do not start the engine). 5. Within 30 seconds, press the driver’s door lock switch in the UNLOCK direction. 6. A single chime will sound to indicate the feature has been changed. 7.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position. To use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY 19 NOTE: The line of transmission must not be blocked with metal objects. To unlock the doors and liftgate: Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors and liftgate. When the UNLOCK button is pressed, the illuminated entry will initiate, and the parking lights will flash on twice.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Test the feature while outside of the vehicle, by pressing the LOCK/UNLOCK button on the keyfob. NOTE: Pressing the LOCK button on the keyfob while you are inside the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. 5. If the desired programming was not achieved or to reactivate this feature, repeat the above steps.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. 6. If the desired programming was not achieved or to reactivate this feature, repeat the above steps. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Fasten your seat belt (Fastening the seatbelt will cancel any chiming that may confuse you during this programming procedure). 3. Place the key into the ignition. 4. Turn the ignition to the ON position ( Do not start the engine ). 5. Press and hold the UNLOCK button on the key fob. 6. After holding the UNLOCK button for four seconds, also press the PANIC button within 6 seconds. 7. When a single chime is heard release both buttons.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Battery Replacement The recommended replacement battery is CR2032. 1. If the key fob is equipped with a screw, remove the screw. With the transmitter buttons facing down, use a flat blade to pry the two halves of the transmitter apart. Make sure not to damage the elastomer seal during removal. 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Set the Alarm: The alarm will set when you use the power door locks or use the Keyless Entry transmitter to lock the doors. After all the doors are locked and closed the security light in the instrument cluster will flash rapidly to signal that the system is arming. The security light in the instrument panel cluster will flash rapidly for about 15 seconds to indicate that the alarm is being set.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNLOCK button or by inserting a programmed Sentry Key into the ignition and turning the key to the ON position. LIFTGATE Once unlocked, the liftgate can be opened or closed without using the key. To open the liftgate, pull out on the outside handle and lift. WARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 WINDOWS Power Windows 2 The control on the left front door has up-down switches that give you finger tip control of all four power windows. There is a single opening and closing switch on the passenger doors for passenger window control.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ignition is turned OFF or the driver’s door is opened. This feature can be turned off by your authorized dealer. NOTE: The Power Accessory Delay feature will allow the power windows to operate for ten minutes after the ignition it turned OFF. Auto Down The driver’s window switch has an Auto Down feature. Push the window switch past the first detent, release, and the window will go down automatically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 window. If you will be carrying children too small for adult-size seat belts, your seat belts or the LATCH feature (refer to the Child Restraint section in this manual), can be used to hold infant and child restraint systems. Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE freely with you under normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out. WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch 31 plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is very dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your dealer and have it fixed. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front and second row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Push in on the anchorage release button to release the anchorage, and then move it up or down to the position that serves you best.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Locking Mode To convert from the normal emergency locking mode to the automatic locking mode, grasp the shoulder belt portion and pull all of the webbing out of the retractor. Allow some of the webbing to retract into the retractor, as the belt retracts you will hear a clicking sound to indicate the seat belt is now in the automatic locking mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Warning System (BeltAlert) will continue to chime and flash the Seat Belt Warning Light for 96 seconds or until the driver’s seat belt is buckled. The Enhanced Warning System (BeltAlert) will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts and Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug against the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbags the instrument panel, above the glove compartment. The words SRS/AIRBAG are embossed on the airbag covers. NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. • If your vehicle is equipped with window bags, do not stack luggage or other cargo up high enough to block the location of the window bag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly. 2. All occupants should use their lap and shoulder belts properly. Here are some simple steps you can follow to minimize the risk of harm from a deploying airbag. 3. The driver and front passenger seats should be moved back as far as practical to allow the airbag room to inflate. 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during airbag deployment could cause serious injury. Airbags need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Driver and Front Passenger Seat Belt Pretensioners • Occupant Classification System (OCS) for the Front Passenger Seat − Occupant Classification Module − Passenger Airbag Disable (PAD) Indicator Light − Weight Sensors The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or RUN positions. These include all of the items listed above except the steering wheel and column, and knee bolsters.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE light either momentarily or continuously. A single chime will sound if the light comes on again after initial start up. WARNING! Ignoring the AIRBAG warning light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE a rear-facing infant seat. Relatively light objects like brief cases and grocery bags will also turn on the PAD Indicator Light. The PAD Indicator Light will be off when teenagers, most children and most children in forward-facing seats are in the front passenger seat. The system is only required to turn the PAD Indicator Light on in the unlikely event that a rear-facing infant seat is installed in front passenger seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The OCS classifies an occupant using weight sensors mounted in the base of the front passenger seat. Any weight on the seat will be sensed by the system. Objects hanging on the seat or other passengers pushing down on the seat will also be sensed. The weight of an adult will cause the system to turn the airbag on. In this case, the OCS has classified the occupant of the seat as an adult.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE under the seat and interferes with operation of the weight sensors, a fault will occur which turns on both the PAD Indicator Light and the Airbag Warning Light. Once the lodged object is removed, the fault will be automatically cleared after a short period of time. Passenger Airbag Off Indicator • The Driver and Passenger Airbag/Inflator Units are located in the center of the steering wheel and the right side of the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Occupant Classification Module (OCM) is located beneath the front passenger seat. The OCM classifies the occupant into categories based on the measurements made by the seat weight sensors. The OCM communicates with the Occupant Restraint Controller (ORC). The ORC uses the occupant category to determine whether the front passenger airbag should be turned off. It also determines the rate of airbag inflation during a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Knee Impact Bolsters help protect the knees of the driver and the front passenger, and position everyone for the best interaction with the front airbag. If A Deployment Occurs The airbag system is designed to deploy the airbags when the impact sensors detect a moderate-to-severe frontal collision, to help restrain the driver and front passenger, and then immediately deflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and the front passenger seat belt retractor assembly, replaced by an authorized dealer as soon as possible. Also, have the Occupant Classification System serviced as well. 49 Maintaining Your Airbag System WARNING! • • • • • Modifications to any part of the airbag system could cause it to fail when you need it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Accident Response System If the airbags deploy after an impact and the electrical system remains functional, vehicles equipped with power door locks will unlock automatically. In addition, approximately 5 seconds after the vehicle has stopped moving, the interior lights will light until the ignition switch is turned off. Airbag Light You will want to have the airbags ready to inflate for your protection in an impact.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants and Small Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult seat belt. Always check the child seat owner’s manual to ensure you have the right seat for your child. Use the restraint that is correct for your child: • This vehicle is not capable of accommodating the installation of a car bed used for carrying newborn babies at the right front passenger seat position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the seat cushion while the child’s back is against the seatback, they need a belt-positioning booster seat. The child and booster seat are held in the vehicle by the lap/shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Standards. The manufacturer recommends that you try a child restraint in the vehicle seats where you will use it before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may not work when you need it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH - Child Seat Anchorage System (Lower Anchors and Tether for CHildren) Your vehicle’s second row seat is equipped with the child restraint anchorage system called LATCH. The LATCH system provides for the installation of the child restraint without using the vehicle’s seat belts, instead securing the child restraint using lower anchorages and upper tether straps from the child restraint to the vehicle structure.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 2 Second Row Left Side Second Row Right Side Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE were provided with the child restraint system. The rear seat lower anchorages are round bars, located at the rear of the seat cushion where it meets the seat back, and are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE to do something more. Disconnect the latch plate from the buckle, turn the latch plate around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position or use the locking clip provided with your child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 2 Second Row Seat
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraints in Third Row Seating (If Equipped) The third seating row is not capable of installing child restraints that require the use of a tether strap. There are no tether anchor provisions for the third seating row in your vehicle, the hooks in the rear floor are not designed to withstand the forces that may occur during a crash. Child Restraint Tether Anchor There are tether strap anchorages behind each seating position in the second row.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Follow the instructions below. See your dealer for help if necessary.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration, within the limits of local traffic laws, contributes to a good break-in. Avoid wide open throttle acceleration in low gear.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • It may be necessary to sit in a parked vehicle with the engine running for more than a short period. If so, adjust your climate control system to force outside air into the vehicle. Set the blower at high speed and the controls in any position except OFF or RECIRC. • The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Outside The Vehicle: Door Latches Check for positive closing, latching and locking. Tires Examine tires for tread wear or uneven wear patterns. Check for stones, nails, glass or other objects lodged in the tread. Fluid Leaks Check the area under vehicle after overnight parking for fuel, water, oil, or other fluid leaks. Also, if gasoline fumes are detected, the cause should be located and corrected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS m Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .70 ▫ Automatic Dimming Mirror — If Equipped . . . .70 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .71 ▫ Exterior Mirrors Folding Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .71 ▫ Electric Remote-Control Mirrors . . . . . . . . . . . .72 ▫ Illuminated Vanity Mirrors — If Equipped .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Front Seats Manual Seat Recliners . . . . . . . . . . .87 ▫ Manual Lumbar Support Adjustment — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .88 ▫ Adjustable Head Restraints — All Seating Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . .88 ▫ 8 - Way Driver’s Power Seat — If Equipped . . .89 ▫ 4 - Way Passenger’s Power Seat — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .89 ▫ Front Heated Seats — If Equipped .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 ▫ Headlights, Parking Lights, Panel Lights . . . . . 106 m Driver Adjustable Pedals — If Equipped . . . . . . 114 ▫ Illuminated Entry . . . . . . . . . . . . . . . . . . . . . 107 ▫ Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 115 ▫ Daytime Running Lights (Canada Only) . . . . . 107 m Electronic Speed Control — If Equipped . . . . . . 116 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . 107 ▫ To Activate . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . 121 m Garage Door Opener — If Equipped . . . . . . . . . 126 ▫ Global Reset . . . . . . . . . . . . . . . . . . . . . . . . . 121 ▫ Programming Homelink . . . . . . . . . . . . . . . . 128 ▫ Step Button . . . . . . . . . . . . . . . . . . . . . . . . . 122 ▫ Canadian Programming/Gate Programming . . 130 ▫ Average Fuel Economy (AVG ECO) . . . . . . . . 122 ▫ Using Homelink . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Electrical Outlet Use With Engine Off (Battery Fed Configuration) . . . . . . . . . . . . . . 136 m Floor Console . . . . . . . . . . . . . . . . . . . . . . . . . 137 69 ▫ Floor Console Features . . . . . . . . . . . . . . . . . 137 m Factory Installed Roof Luggage Rack— If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of truck). The mirror should be adjusted while set in the day position (toward windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Exterior Mirrors Folding Feature — If Equipped Folding exterior mirrors are hinged and may be moved either forward or rearward to resist damage. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electric Remote-Control Mirrors The controls for the power mirrors are located on the driver’s door trim panel. To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When you are finished adjusting the mirror, turn the control to the center position to prevent accidentally moving a mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 WARNING! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side mirror. Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on each sun visor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Driver’s Exterior Mirror — If Equipped This mirror will automatically adjust for annoying light glare from vehicles behind you. This feature is controlled by the inside mirror and can be turned off by pressing the button at the base of the inside mirror. HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in-vehicle communications system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE access the system. The diagram below shows the mirror with the appropriate buttons. Individual button behavior is discussed in the “Operation” Section. 75 The UConnect™ system can be used with any Hands Free Profile certified Bluetooth™ cellular phone. If your cellular phone has a different profile (i.e. headset profile), you will not be able to use any UConnect™ features.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Operation Voice commands can be used in the operation of the UConnect™ system and to navigate through the UConnect™ menu structure. Voice commands should be given after each UConnect™ system prompt. You will be prompted for a specific command and then guided through the available options. There are two ways to give commands to the UConnect™ system: • You can say 9Dial9 at the 9Ready9 prompt.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 • You will then be asked to give your cellular phone a priority level between 1 and 7, 1 having the highest priority. You can connect up to seven cellular phones to your UConnect™ system and the priority allows the UConnect™ system to know which cellular phone to use if multiple cellular phones are in the vehicle at the same time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Next, enter the number designation (e.g. “Home”, “Work”, “Mobile”, or “Pager”). This will allow you to have multiple numbers for each phonebook entry. • Recite the phone number for the phonebook entry that you are adding. After you are finished adding an entry into the phonebook, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Delete Entries in the UConnect™ Phonebook Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • Press the ’Phone’ button to begin. • After the 9Ready9 prompt, say 9Phonebook Delete9. • After the 9Ready9 prompt, say 9Phonebook Delete All9. • After you enter the phonebook delete menu, you will then be asked for the name of the phonebook entry that you wish to delete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To call one of the names in the list, press the ’Voice Recognition’ button during the playing of the desired name and say 9Call9. • The UConnect™ system will then prompt you as to number designation you wish to call. • The selected number will be dialed. Phone Call Features The following feature(s) can be accessed through the UConnect™ system if the feature(s) are available on your cellular service plan.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Putting a Call on Hold and Retrieving a Call from Hold To put a call on hold, press the ’Phone’ button until you hear a single beep which will indicate that the call has been placed on hold. To bring the call back from hold, press the ’Phone’ button. Toggling Between Two Calls If two calls are in progress (one active and one on hold), press the ’Phone’ button until you hear a single beep indicating that the active and hold status of the two calls have switched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Advanced Phone Connectivity • At the next prompt, say 9Delete9. Transferring an Active Call between the UConnect™ System and Your Cellular Phone The UConnect™ system allows ongoing calls to be transferred to your cellular phone or to the UConnect™ system without terminating the call. To transfer an ongoing call from your cellular phone to the UConnect™ system or vice versa, press the ’Voice Recognition’ button and say 9Transfer Call9.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE List Paired Cellular Phone Names • Press the ’Phone’ button to begin. • After the 9Ready9 prompt, say 9Setup List Phones9 and the UConnect™ system will play the phone names of all paired cellular phones in order from highest priority to lowest priority. Select a Lower Priority Paired Cellular Phone • Press the ’Phone’ button to begin. • After the 9Ready9 prompt, say 9Setup9. • When prompted, say “Select Phone”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE are pressing a number on your keypad to navigate through a menu structure or to enter a number for a pager. Barge In - Overriding Prompts The ’Voice Recognition’ button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect™ system. By dialing a number with your paired Bluetooth™ cellular phone, the audio will be played through your vehicle’s stereo system. The UConnect™ system will work the same as if you dialed the number using voice recognition.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Front Seat Manual Seat Adjustment The adjusting lever is at the front of the seat, near the floor. Lift the lever and move the seat to the desired position. Release the bar to lock the seat into position. Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. 87 Front Seats Manual Seat Recliners The bucket seats are equipped with recliners. The reclining mechanism is operated by a control located on the outboard side of the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Lumbar Support Adjustment — If Equipped The manual lumbar support adjustment lever is located on the right side of the driver’s seat and on the left side of the passenger’s seat. Moving the lumbar control lever fore and aft increases or decreases the lumbar support. Adjustable Head Restraints — All Seating Positions Head restraints can reduce the risk of whiplash injury in the event of impact from the rear.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 3 8 - Way Driver’s Power Seat — If Equipped The driver’s power seat switches are located on the outboard side of the driver’s seat lower side trim. The bottom switch controls up/down, forward/rearward, and tilt adjustment. The top switch controls the seatback recline adjustment. 4 - Way Passenger’s Power Seat — If Equipped The front passenger’s power seat switches are located on the outboard side of the passenger seat lower side trim.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Heated Seats — If Equipped This feature heats the driver and front passenger seats. The controls for the front heated seats are located on the center of the instrument panel, below the climate controls. The heated seat system allows the driver and front passenger to select from two different levels of supplemental electrical seat heating, or no seat heating to suit their individual comfort requirements.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 then the system will turn off. Thus, a maximum of four hours of operation until the system is reactivated. seatbacks to fold with spring assistance. In this position, the back is horizontal and aligned to the rear floor. If the low heat setting is initially selected, the system will operate for two hours and then turn off. Second row leather seats have seatback recliners at the 40% seating positions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Raising the lever allows third row seat passengers to fold the seatbacks and release the latches when exiting the vehicle. Once the seatback is in a folded position continue raising the lever fully to release the cushion latches and tumble the seat. This folding and tumbling action provides easy access to the third row seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Third Row Seat Bench — If Equipped To Fold The Seats Folding the third seat occurs in two stages: the cushion is lifted and moved forward then the back is folded. Pull up and forward on either one of the 2 straps at the front of the cushion. The cushion rises on the ends of the U-shaped bracket that pivots on the floor underneath the cushion. If you continue to pull forward, the cushion drops back to the floor directly behind the second seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Flat Load Floor Unsnap the flipper panels on the third row seats and flip them forward on the back(s) of the second row seat(s).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Achieve Maximum Cargo Capacity Pull up the release handles and strap on the second row seats and fold the seat backs flat. Then fold the third row seat flat. Unsnap the flipper panel on the third row seat and flip it forward on the backs of the second row seats. NOTE: When returning the second row seats to their upright position, always snap the third row seat flipper panel(s) back to the third row seat first.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Third Seat 50/50 Split Seat — If Equipped simultaneously into a flat load floor position. The cushion and back will move forward together resting on the floor behind the second row seats. The seat belt buckles are hinged to fold with the seatback. To extend the load floor, unsnap the straps and flip the flipper panel(s) on the third row seat forward on the back(s) of the second row seat(s).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 To Return The Seat(s) To An Upright Position Snap the flipper panel(s) on the seat back. Then pull on the pull strap on the seat back to reposition the seat(s) to an upright position. NOTE: Make sure the seatback is properly engaged to lock the seatback to a upright position. This can be verified by pulling/pushing forward on the seatback. The seatback will not move forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE preset settings. Your Remote Keyless Entry transmitters can also be programmed to recall the same positions when the UNLOCK button is pressed. can accommodate up to two transmitters, each transmitter linked to either of the two memory positions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Adjust the Automatic Temperature Control (ATC) while the ATC is in Auto mode. 5. Press and release the SET (S) button located on the driver’s door. 6. Within 5 seconds, press and release memory button 1 or 2 on the driver’s door. The next step must be performed within 10 seconds if you desire to also use a Remote Keyless Entry transmitter to recall memory positions. 7. Press and release the LOCK button on one of the transmitters. 8.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE A recall can be cancelled by pressing any of the memory buttons on the drivers door during a recall (S, 1, or 2), or pressing any one of the power seat buttons, or pressing the adjustable pedals button, or pressing either the LOCK or UNLOCK button on the remote keyless entry transmitter when not in the ignition switch. When a recall is cancelled, the driver’s seat, and the pedals stop moving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE control may be restored by first reaching the recently limited or obstructed position, then release and reactivate the same button or buttons. Continued seat travel beyond the obstructed position will indicate the recently encountered self-limitation has been cleared. Driver Easy Exit and Easy Entry Control This additional feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Then push the safety latch lever to the right. It is located between the grille openings left of the center. To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the second upward detent position, or when the UNLOCK button is pressed on the key fob.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 all the way down to the OFF detent will cause all the interior lights to go out. This allows the doors to stay open for extended periods of time without discharging the vehicle’s battery. If the ignition is off and any door is left ajar for eight minutes or the dimmer control is rotated upwards for eight minutes, the interior lights will automatically turn off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlight Delay To aid in your exit, your vehicle is equipped with a headlight delay that will leave the headlights on for 90 seconds. This delay is initiated when the ignition is cycled off while the headlight switch is on, and then the headlight switch is cycled off. The headlights will remain on for 90 seconds. Headlight delay can be cancelled by either turning the headlight switch ON then OFF or by turning the ignition ON.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Entry Headlights turn on for 90 seconds, when the Remote Keyless Entry UNLOCK button is pressed. NOTE: This feature can be activated by your authorized dealer. 107 Lights-on Reminder If the headlights, parking lights, or courtesy lights are left On, after the ignition is turned Off, a chime will sound when the driver’s door is opened.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE position and pressing the fog light button. The fog lights will operate only when the parking lights are ON or when the vehicle headlights are ON low beam. An indicator light located in the instrument cluster will illuminate when the fog lights are on. The fog lights will turn off when the switch is pressed in, when the headlight switch is rotated to the OFF position, or the high beam is selected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE of the front and rear turn signal lights. If an indicator fails to light when the lever is moved, it would suggest that the switch or indicator lamp is defective. If a defective bulb or wiring circuit is detected for the turn signal system, the arrow indicators will flash at a faster rate. You can signal a lane change by moving the lever partially up or down. NOTE: If a turn signal has been left on for at least a mile duration, a continuous chime will sound.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wipers Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range. The delay interval decreases as you rotate the knob until it enters the LO continual speed position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during windshield washer use. NOTE: If the front wiper is operating when the ignition is turned off, the wiper will automatically return to the 9Park9 position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TRACTION CONTROL SWITCH — IF EQUIPPED Traction control monitors the amount of wheel spin in each of the driven wheels. If wheel spin is detected, the pressure to the brake system of the slipping wheel(s) is modulated to provide enhanced acceleration. The system operates at speeds typically encountered in city traffic driving. 4WD drive models also include unique logic in 4HI or 4LO to enhance off-road capabilities.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 To turn the system back ON, press the switch a second time until the traction control Indicator turns OFF. NOTE: • The traction control Indicator comes on each time the ignition switch is turned ON. This will occur even if you used the switch to turn the system OFF. • The Traction Control system will make buzzing or clicking sounds when in operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! DRIVER ADJUSTABLE PEDALS — IF EQUIPPED Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving. The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustment 1. Position the driver seat so that you are at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel. 2. Fasten and adjust the seatbelts. 3. Move the adjustable pedal switch, located to the left of the steering column near the parking brake release, up to move the pedals toward the driver or down to move the pedals away from the driver. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over accelerator operation at speeds greater than (refer to the table below for the speed for your specific engine). The controls are mounted on the steering wheel. To Activate Push the ON/OFF button to the ON position. In the instrument cluster, the word “CRUISE” illuminates when the system is on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Speed Control ON when not in use is dangerous. You could accidentally set the system to cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you aren’t using it. To Resume Speed To resume a previously set speed, push and release the RESUME button. Resume can be used at any speed above (refer to the table below for the speed for your specific engine).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Functions Engage Speed Minimun RESUME Speed ACCEL Increase COAST Decrease Dropout Speed 3.7L 35 mph (56 km/h) 30 mph (50 km/h) 2 mph (3km/h) 1 mph (2 km/h) 30 mph (50 km/h) To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 WARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy/Reading Lights Near the front of the console are two courtesy/reading lights. Both lights illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (fully upward position), or when the UNLOCK button is pressed on the Remote Keyless Entry transmitter, if so equipped. These lights are also operated individually as reading lights by pressing the recessed area of the corresponding lens.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE RESET Button Use this button to reset the following displays to zero: Average Fuel Economy Trip Odometer Elapsed time. 121 Global Reset If the RESET button and STEP button are pressed at the same time and held for 3 seconds the Global Reset feature will reset the distance to empty (using a default fuel economy value), fuel economy, trip odometer, and elapsed time displays.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Step Button Use this button to choose or cycle through the four trip conditions. Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. This display mode becomes less sensitive to instantaneous changes in fuel consumption as the number of total vehicle miles since the last reset increases.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE fuel capacity, which corresponds to approximately 8% of tank volume. This reserve capacity was put in place to prevent the likelihood of customers running out of fuel when operating at maximum load conditions in areas where there aren’t many gas stations. 123 C/T Button 3 NOTE: The Distance To Empty will remain equal to zero, until the vehicle runs out of fuel or is refueled. Trip Odometer (ODO) This display shows the distance traveled since the last reset.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass/Temperature Display WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible personal injury or property damage. Automatic Compass Calibration This compass is self-calibrating which eliminates the need to manually set the compass.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 free from large metal objects or power lines. The CAL symbol will turn off and the compass will function normally. Compass Variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set according to the Compass Variance Map.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press and hold the RESET button approximately five seconds. The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 WARNING! For additional information on HomeLinkt, call 1–800– 355–3515, or on the internet at www.homelink.com. A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming HomeLink NOTE: When programming a garage door opener, it is advised to park outside the garage. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio-frequency signal. 1. Press and hold the two outer HomeLink buttons, and release only when the indicator light begins to flash (after 20 seconds).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects. 2. Position the end of your hand-held transmitter 1-3 inches (3-8 cm) away from the HomeLink buttons while keeping the indicator light in view. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with (Programming( steps 6-8 to complete the programming of a rolling code equipped device (most commonly a garage door opener). 6. At the garage door opener receiver (motor-head unit) in the garage, locate the 9learn9 or 9smart9 button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 7.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you live in Canada or you are having difficulties programming a gate operator by using the 9Programming9 procedures (regardless of where you live), replace (Programming HomeLink( step 3 with the following: NOTE: If programming a garage door opener or gate operator, it is advised to unplug the device during the 9cycling9 process to prevent possible overheating. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming a Single HomeLink Button To program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1. Press and hold the desired HomeLink button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink button, proceed with 9Programming9 step 2 For questions or comments, contact HomeLink at: www.homelink.com or 1-800-355-3515.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE HomeLinkt is a trademark owned by Johnson Controls, Inc. POWER SUNROOF — IF EQUIPPED The power sunroof control is located between the sun visors on the overhead console. Pressing the 9open9 end of the rocker switch once moves the panel to a comfort stop position short of full opening. Pressing and holding the switch causes the panel to continue moving rearward, up to the full-open position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a nonabrasive cleaner and a soft cloth to clean the glass panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine OFF (Battery Fed Configuration) CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e. coolers, vacuum cleaners, lights, etc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 FLOOR CONSOLE Floor Console Features The Floor Console between the driver’s and front passenger’s seat, has the following features: • Miscellaneous storage compartments • Flexible cup holder inserts • Portable phone storage bin • Portable phone cord routing • 12 Volt battery fed power outlet inside storage compartment • Side open armrest lid • Tissue holder & pen holder • Coin slots • Removable CD bin 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The coin slots are located under the instrument panel center stack. Cup Holders The Durango has 8 cupholders. Four are located in the center console, two are located in the second row armrest, and two are located in the right hand quarter panel for third row occupants. The four cupholders located in the center console may be removed for cleaning and are dishwasher safe.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE FACTORY INSTALLED ROOF LUGGAGE RACK— IF EQUIPPED 139 The side rails between the stantions should be used to tie down cargo. Check the straps frequently to be sure that the load remains securely attached. NOTE: Crossbars are offered by Mopart accessories. External racks do not increase the total load carrying capacity of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity. Always distribute heavy loads as evenly as possible and secure the load appropriately. Long loads which extend over the windshield, such as wood panels or surfboards, should be secured to both the front and rear of the vehicle. Cargo must be securely tied before driving your vehicle.
INSTRUMENT PANEL AND CONTROLS CONTENTS m Instruments And Controls . . . . . . . . . . . . . . . . . 144 m Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 145 m Instrument Cluster Description . . . . . . . . . . . . . 146 m Radio Reception Information . . . . . . . . . . . . . . . 154 ▫ AM Reception . . . . . . . . . . . . . . . . . . . . . . . 154 ▫ FM Reception . . . . . . . . . . . . . . . . . . . . . . . . 154 m Electronic Digital Clock . . . . . . . . . . . . . . . . . .
INSTRUMENT PANEL AND CONTROLS ▫ Operation Instructions (CD Mode For CD Audio Play) . . . . . . . . . . . 165 ▫ Load/Eject Button (CD Mode For CD Audio Play) . . . . . . . . . . . 166 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . . 168 ▫ Operation Instructions (CD Mode For MP3 Audio Play) . . . . . . . . . . 171 ▫ Load/Eject Button (CD Mode For MP3 Play) . . 171 m Satellite Radio — If Equipped . . . . . . . . . . . . . . 173 ▫ System Activation . . . . . . . . . . . . . . . . . . . . .
INSTRUMENT PANEL AND CONTROLS 143 m Climate Controls . . . . . . . . . . . . . . . . . . . . . . . 179 ▫ Level Of Automatic Control . . . . . . . . . . . . . . 185 ▫ Manual Control . . . . . . . . . . . . . . . . . . . . . . 179 ▫ Manual Control (ATC) . . . . . . . . . . . . . . . . . . 186 ▫ Air Conditioning Operation . . . . . . . . . . . . . . 180 ▫ Rear Zone Climate Control — If Equipped . . . 189 ▫ Front Blower Control . . . . . . . . . . . . . . . . . . .
INSTRUMENT PANEL AND CONTROLS INSTRUMENTS AND CONTROLS
INSTRUMENT PANEL AND CONTROLS 145 Instrument Cluster 4
INSTRUMENT PANEL AND CONTROLS INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gage The fuel gauge shows level of fuel in tank when ignition switch is in the ON position. 2. Temperature Gage The temperature gage indicates engine coolant temperature. Any reading within the normal range indicates that the cooling system is operating satisfactorily.
INSTRUMENT PANEL AND CONTROLS 147 left/right turn signal is left on with the engine RPM vehicle speed greater than 15 mph (24 km/h) for more than one mile. 7. Fog Light Indicator — If Equipped This light shows when the fog lights are ON. 4. Low Fuel Warning Light This indicator lights when the fuel gauge reads 1/8 of a tank or less. 8. Coolant Temperature Light This light warns of an overheated engine condition. For a bulb check, this light will come on momentarily when the ignition is turned On.
INSTRUMENT PANEL AND CONTROLS CAUTION! WARNING! Driving with a hot engine cooling system could damage your vehicle. If the temperature light is on, safely pull over and stop the vehicle. Idle the vehicle in neutral with the air conditioner turned off until the light turns off. If the if the light remains on, turn the engine off immediately, and call for service. A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant.
INSTRUMENT PANEL AND CONTROLS engine is started. If the light stays on or turns on while driving, it indicates a problem with the charging system. Immediate service should be obtained. 11. Liftgate Open The Gate Open light will illuminate when the liftgate is not properly closed and the ignition is ON. 12. Security Light This light will flash rapidly for approximately 15 seconds when the vehicle theft alarm is arming. The light will flash at a slower speed continuously after the alarm is set.
INSTRUMENT PANEL AND CONTROLS each position to all other positions. For a good signal the display will place a box around the selected transmission range (PRND21). If the PRNDL displays only the characters PRND21 (no boxes) have the system checked by an authorized dealer. 17. Transfer Case Position and Service (SVC) Indicators These lights monitor the electric shift 4WD system for transfer case position and function.
INSTRUMENT PANEL AND CONTROLS NOTE: Extended heavy use of Traction Control may cause the system to deactivate and turn on the Traction Control indicator. This is to prevent overheating of the brake system and is a normal condition. The system will remain disabled for about 4 minutes until the brakes have cooled. The system will automatically reactivate and turn off the Traction Control indicator. 19.
INSTRUMENT PANEL AND CONTROLS light stays on, it may be an indication that the parking brake has not been released, or there is a low brake fluid level. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction. In this case, the light will remain on until the condition has been corrected.
INSTRUMENT PANEL AND CONTROLS CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. 25. Airbag Indicator The indicator lights and remains lit for 6 to 8 seconds when the ignition is first turned ON.
INSTRUMENT PANEL AND CONTROLS The trip odometer shows individual trip mileage. To toggle between the odometer and the trip odometer, press the Odometer/Trip Odometer Button. 29. Odometer/Trip Odometer Button Press this button to toggle between the odometer and the trip odometer display. Holding the button in resets the trip odometer reading. RADIO RECEPTION INFORMATION AM Reception AM radio signals usually travel longer distances than FM signals, especially at night.
INSTRUMENT PANEL AND CONTROLS Clock Setting Procedure 1. Press and hold the time button until the hours blink. 155 SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL HANDS FREE PHONE CAPABILITY 2. Adjust the hours by turning the right side Tune / Audio control. 3. After the hours are adjusted, press the right side Tune / Audio control to set the minutes. 4. Adjust the minutes using the right side Tune / Audio control. 5. To exit, press any button/knob or wait approximately 5 seconds.
INSTRUMENT PANEL AND CONTROLS Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it.
INSTRUMENT PANEL AND CONTROLS NOTE: In Hands Free Phone (if equipped) mode, the MUTE button mutes the microphone. SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time.
INSTRUMENT PANEL AND CONTROLS Press the rotary TUNE control a third time and TREBLE will display. Turn the TUNE control to the right or left to increase or decrease the Treble tones. Press the rotary TUNE control a fourth time and BAL will display. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers. Press the rotary TUNE control a fifth time and FADE will display.
INSTRUMENT PANEL AND CONTROLS Preset Buttons 1 - 6 (Radio Mode) These buttons tune the Radio to the stations that you commit to push-button memory {12 AM, 12 FM, and 12 Satellite (if equipped) stations}. Operation Instructions - CD Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Inserting The Compact Disc (Single CD Player) Gently insert one CD into the CD player with the CD label facing up.
INSTRUMENT PANEL AND CONTROLS SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal. The unit will switch to the last selected mode. If you do not remove the disc within 15 seconds, it will be reloaded. The radio mode will continue to appear.
INSTRUMENT PANEL AND CONTROLS Operating Instructions - Hands Free Phone — If Equipped Refer to the HANDS FREE PHONE (UConnect™) section of the Owner’s Manual. SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, AND VIDEO CAPABILITIES 161 Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON.
INSTRUMENT PANEL AND CONTROLS Mode Button (Radio Mode) Press the mode button repeatedly to select between the Radio, CD player, Hands Free Phone, Satellite, or Vehicle Entertainment System (VES) (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down.
INSTRUMENT PANEL AND CONTROLS RW/FF (Radio Mode) Pressing the rewind/fast forward button causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM, FM or Satellite (if equipped) frequencies. TUNE Control (Radio Mode) Turn the right side rotary control to increase or decrease the frequency. AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control and BASS will display.
INSTRUMENT PANEL AND CONTROLS within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broadcast PTY information.
INSTRUMENT PANEL AND CONTROLS By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
INSTRUMENT PANEL AND CONTROLS begin to play when you insert the disc. The display will show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. SEEK Button (CD MODE For CD Audio Play) Press the right side of the SEEK button for the next selection on the CD.
INSTRUMENT PANEL AND CONTROLS LOAD / EJECT - Eject Press the LOAD/ EJECT button and the pushbutton with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show 9EJECTING DISC9 when the disc is being ejected and prompt the user to remove the disc. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not removed, the radio will continue to play the non-removed CD.
INSTRUMENT PANEL AND CONTROLS RND/PTY Button (Random Play Button) (CD MODE For CD Audio Play) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track. Press and hold the FF button to fast forward through the tracks. Release the FF button to stop the fast forward feature.
INSTRUMENT PANEL AND CONTROLS • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator 9.9 and a 3-character extension) • Level 2: 31 (including a separator 9.9 and a 3-character extension) Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files).
INSTRUMENT PANEL AND CONTROLS MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 Sampling Frequency (kHz) 48, 44.1, 32 24, 22.05, 16 Bit rate (kbps) 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 ID3 Tag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported.
INSTRUMENT PANEL AND CONTROLS Operation Instructions - (CD Mode For MP3 Audio Play) SEEK Button (CD Mode For MP3 Play) Pressing the right side of the SEEK button plays the next MP3 File. Pressing the left side of the SEEK button plays the beginning of the MP3 file. Pressing the button within the first ten seconds plays the previous file. LOAD/EJECT Button (CD Mode For MP3 Play) LOAD/ EJECT - Load Press the LOAD/ EJECT button and the pushbutton with the corresponding number where the CD is being loaded.
INSTRUMENT PANEL AND CONTROLS Press the MSG button once more to return to 9elapsed time9 priority mode. Press and hold the MSG button while in the message display priority mode or elapsed time display priority mode will display the song title for each file. SET/DIR Button (CD Mode For MP3 Play) Press the SET/DIR Button to display folders, when playing an MP3 discs that have a file/folder structure. Turn the TUNE control to display available folders or move through available folders.
INSTRUMENT PANEL AND CONTROLS Operating Instructions - Video Entertainment System (VESt) (If Equipped) Refer to separate Video Entertainment System (VESt) Guide. SATELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius™ Satellite Radio.
INSTRUMENT PANEL AND CONTROLS ESN/SID mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. ESN/SID Access With RAQ Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and TIME buttons simultaneously for 3 seconds. All twelve ESN/SID numbers will be displayed.
INSTRUMENT PANEL AND CONTROLS 175 Selecting a Channel Press and release the SEEK or TUNE buttons to search for the next channel. Press the top of the button to search up and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released. Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory.
INSTRUMENT PANEL AND CONTROLS one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. Reception Quality Satellite reception may be interrupted due to one of the following reasons. PTY Button (SEEK( When the desired program is obtained, press the 9SEEK9 button within five seconds. The channel will change to the next channel that matches the program type selected.
INSTRUMENT PANEL AND CONTROLS REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. 177 The right hand control is a rocker type switch with a push button in the center. Pressing the top of the switch will increase the volume and pressing the bottom of the switch will decrease the volume. The button located in the center of the right hand control will switch modes to Radio or CD.
INSTRUMENT PANEL AND CONTROLS The button located in the center of the left hand control will tune to the next pre-set station that you have programmed in the radio pre-set push-buttons. COMPACT DISC MAINTENANCE To keep the compact discs in good condition, take the following precautions: CD Player Pressing the top of the switch once will go to the next track on the CD.
INSTRUMENT PANEL AND CONTROLS NOTE: If you experience difficulty in playing a particular disc, it may be damaged (i.e. scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have theft protection encoding. Try a known good disc before considering disc player service. RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio.
INSTRUMENT PANEL AND CONTROLS Air Conditioning Operation To turn the air conditioning On or Off perform the following steps: • Position the mode control button to the desired airflow setting. engine speed or power may be noticed when the compressor is on. This is a normal occurrence since the compressor will cycle on and off to maintain comfort and improve fuel economy. Front Blower Control The Front Blower controls the amount of air delivered to the passenger compartment.
INSTRUMENT PANEL AND CONTROLS Front Mode Control The mode control allows you to choose from several patterns of air distribution. NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are identified by the small dots and give an even blend of both modes.
INSTRUMENT PANEL AND CONTROLS NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. Defrost Outside air is primarily directed to the windshield through the defroster outlet located at the base of the windshield and side window demist outlets. Heat (Floor) Outside air flows primarily through the floor outlets located under the instrument panel.
INSTRUMENT PANEL AND CONTROLS Temperature Control The temperature of the air is controlled by a slide located on the top center of the control panel. Move the slide left or right to change the temperature. The blue area of the scale indicates cooler temperatures while the red area indicates warmer temperatures.
INSTRUMENT PANEL AND CONTROLS mode on the front control will give you air from the outlets in the headliner in the rear. Floor mode in the front will give you floor in the rear. Rear Window Defrosting and Rear Window Washer/Wiper See the “Rear Window Features” section of this book. Automatic Temperature Control (ATC) — If Equipped The control can be turned on by pressing the POWER button. When the control is turned on, it will be in the last mode prior to being turned off.
INSTRUMENT PANEL AND CONTROLS The ATC system uses an infrared sensor located in the overhead console to measure the temperature of the driver. Based on the sensor input, the system will automatically control comfort by varying the temperature, fan speed, and mode. This maintains a comfortable temperature, even under changing conditions. It is important that the infrared sensor is kept clean and that objects are not blocking the sensor.
INSTRUMENT PANEL AND CONTROLS Manual Control (ATC) You also may choose to customize your comfort by selecting the fan speed and mode manually. Pressing the fan speed button or any mode button places the system into manual operation. While in manual operation there are six fan speeds available and the choice of any mode. The airflow temperature is adjusted automatically to maintain the desired comfort level. You can adjust the temperature by pressing the + or – TEMP rocker switch.
INSTRUMENT PANEL AND CONTROLS Manual control of Recirculation is possible only in Panel, Floor, and Bi-Level modes. It will not operate in Mix, or Defrost modes. The recirculation symbol will flash three times indicating recirculation is not available in these modes. NOTE: If the interior of the windows begin to fog, press the recirculate button to return to outside air. Some conditions will cause captured interior air to fog windows when in recirculate mode.
INSTRUMENT PANEL AND CONTROLS the A/C snowflake button has not been pressed. This dehumidifies the air to help dry the windshield. Rear Temperature Control (ATC) The “REAR FUNCTIONS” button cycles through the following modes: Rear Control from Front This allows the driver or passenger to control the rear blower speeds using the FAN +/– rocker switch and the rear temperature using the TEMP +/– rocker switch. While in this mode, pressing the POWER button will turn the rear system off.
INSTRUMENT PANEL AND CONTROLS 189 Rear Zone Climate Control — If Equipped 4 Headliner air comes from the outlets in the headliner. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vane knobs on the outlets to one side will shut off the airflow. The rear compartment control uses two rotary knobs: one for the temperature control and the other for the fan speed control.
INSTRUMENT PANEL AND CONTROLS Rear Rotary Blower Control The second row seat occupants have control of the rear blower speed, only when the front control unit is in the “REAR CONTROL” position. The rear blower switch has an “Off” position and a range of blower speeds. Rotating the rear blower control clockwise will increase the blower speed.
INSTRUMENT PANEL AND CONTROLS Front Unit to Rear Unit Chart If the Front Control is selected Panel Bi-Level • Between Bi-Level Floor Floor Mix Defrost Rear Airflow will come from Headliner Headliner Bi-Level Floor Floor Floor Operating Tips Fast Cooldown For a fast cooldown, set the blower fan to the highest setting, set the mode control to the panel fresh position, press the snowflake button to turn on the air conditioning, and drive with the windows open for the first few minutes.
INSTRUMENT PANEL AND CONTROLS and blower speed to maintain comfort. Interior fogging on the windshield can be quickly removed by selecting the defrost mode. Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging.
INSTRUMENT PANEL AND CONTROLS 193 Operating Tips Chart 4
INSTRUMENT PANEL AND CONTROLS REAR WINDOW FEATURES Rear Window Wiper/Washer A rotating switch located on the climate control panel turns the rear wiper On or Off. Pressing the rotating switch inward activates the rear window washer. Rotating the switch will enable one of five intermittent delay times for the rear wiper. The delay times range from 20 to 1 second.
INSTRUMENT PANEL AND CONTROLS If the rear wiper is operating when the ignition is turned off, the wiper will automatically return to the “Park” position. When the vehicle is restarted, the wiper will resume operation. Rear Window Defrosting A push-button type switch is located in the climate control panel. Press the switch and the rear window defroster and electric remote control heated mirrors (if equipped) will turn On. An amber indicator on the push-button will light when the defroster is turned On.
STARTING AND OPERATING CONTENTS m Starting Procedures . . . . . . . . . . . . . . . . . . . . . 200 ▫ Shifting Procedure - NV 144 Transfer Case . . . 210 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 200 ▫ NV 244 Generation II Transfer Case Operating Information / Precautions . . . . . . . . . . . . . . . 211 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 201 ▫ Engine Block Heater — If Equipped . . . . . . . . 202 m Automatic Transmission . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING m Tire Safety Information . . . . . . . . . . . . . . . . . . . 221 ▫ Alignment And Balance . . . . . . . . . . . . . . . . . 238 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 221 m Supplemental Tire Pressure Information . . . . . . . 239 ▫ Tire Identification Number (TIN) . . . . . . . . . . 225 m Tire Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . 239 ▫ Tire Loading And Tire Pressure . . . . . . . . . . . 226 m Snow Tires . . . . . . . .
STARTING AND OPERATING 199 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . . . 248 ▫ Trailer Towing Requirements . . . . . . . . . . . . . 258 m Catalytic Converter . . . . . . . . . . . . . . . . . . . . . 249 ▫ Trailer Tow Wiring . . . . . . . . . . . . . . . . . . . . 259 m Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . . . 250 ▫ Cooling System Tips—Trailer Towing . . . . . . . 260 ▫ Certification Label . . . . . . . . . . . . . . . . . . . . . 250 m Snowplow . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES The starter should not be operated for more than 15second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. Automatic Transmission Start the engine with the selector lever in NEUTRAL or PARK position. Apply the brake before shifting to any driving range. WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way.
STARTING AND OPERATING Normal Starting Normal Starting of either a warm or cold engine is obtained without pumping or depressing the accelerator pedal. Turn the key to the START position and release when the engine starts. If the engine fails to start within 10 seconds, turn the key to the OFF position, wait 5 seconds, then repeat the starting procedure. If Engine Fails To Start If the engine fails to start after you have followed the Normal Starting procedure, it may be flooded.
STARTING AND OPERATING WARNING! WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. After Starting The idle speed is automatically controlled on fuel injected engines and will decrease as the engine warms up.
STARTING AND OPERATING WARNING! Remember to disconnect the cord before driving. Damage to the 110-115 volt electrical cord could cause electrocution. AUTOMATIC TRANSMISSION Automatic Transmission The electronic PRNDL on the instrument cluster indicates the transmission gear selected. The selector lever is mounted on the right side of the steering column. To drive, move the selector lever from Park or Neutral to the desired drive position.
STARTING AND OPERATING WARNING! WARNING! Your vehicle could move and injure you and others if it is not completely in P (Park). Check by trying to move the gearshift lever back and forth without first pulling the lever toward you, after you have set it in P (Park). Make sure it is in Park before leaving the vehicle. It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed.
STARTING AND OPERATING 205 “N” Neutral Shift to Neutral when vehicle is standing for prolonged periods with engine running. Engine may be started in this range. Set the parking brake if you must leave the vehicle. “1” First For driving up very steep hills and for engine braking at low speeds 25 mph (40 km/h) or less when going down hill. To prevent excessive engine speed do not exceed 25 mph (40 km/h) in this range. “D” Drive For most city and highway driving.
STARTING AND OPERATING • transmission has reached normal operating temperature. NOTE: If the vehicle is started in extremely cold temperatures, the transmission may not shift into Overdrive and will automatically select the most desirable gear for operation at this temperature. Normal operation will resume when the transmission fluid temperature has risen to a suitable level. Refer also to the Note under torque converter clutch, later in this section.
STARTING AND OPERATING performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in “TOW/HAUL” mode, 5th gear (if equipped) is disabled and 2-3 and 3-4 shift patterns are modified. Shifts into Overdrive (4th gear) are allowed during steady cruise (for improved fuel economy) and automatic closed-throttle downshifts to 3rd gear (for improved braking) will occur during steady braking.
STARTING AND OPERATING transmission into gear may seem sluggish. This is due to the fluid partially draining from the torque converter into the transmission. This condition is normal and will not cause damage to the transmission. The torque converter will refill within five seconds of shifting from Park into any other gear position.
STARTING AND OPERATING 209 or illuminates during driving, it means that the 4WD system is not functioning properly and that service is required. Proper operation of four-wheel-drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the transfer case. WARNING! Because four-wheel-drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road conditions permit.
STARTING AND OPERATING 4LOCK Four-Wheel-Drive LOCK - Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only. Shifting Procedure - NV 144 Transfer Case AWD to 4LOCK or 4LOCK to AWD With the key ON and the engine either OFF or RUNNING, rotate the transfer case switch, located on the instrument panel to the desired position.
STARTING AND OPERATING NOTE: Delayed shifting out of 4LOCK may be experienced due to uneven tire wear, low tire pressure, or excessive vehicle loading. NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift.The indicator light will flash and the current transfer case position will be maintained.To retry a selection, turn the control knob back to the current position, wait five (5) seconds, and retry the shift.
STARTING AND OPERATING vehicle in the 4LOCK position on dry hard surfaced roads. This feature provides the safety, security, and convenience of operating in all-wheel drive at all times regardless of road conditions. NOTE: The transfer case Neutral (N) position is to be used for recreational towing only. See Recreational Towing section for specific procedures on shifting into and out of Neutral (N).
STARTING AND OPERATING WARNING! Always engage the parking brake when powering down the vehicle if the (Service 4WD( light is illuminated. Not engaging the parking brake may allow the vehicle to roll which may cause personal injury. NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning. The NV 244 Generation II transfer case is not equipped with a synchronizer and therefore the front and rear driveshaft speeds must be equal for the shift to take place.
STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position. The parking brake should always be applied when the driver is not in the vehicle.
STARTING AND OPERATING Shifting Procedure - NV 244 Generation II Transfer Case 215 wheels to complete the shift. There may be a delay up to 13 seconds for the shift to complete after the wheels have stopped spinning. NOTE: Delayed shifting out of the 4LOCK position may be experienced due to uneven tire wear, low tire pressure, or excessive loading. NOTE: When shifting into or out of 4LO some gear noise may be heard. This noise is normal and is not detrimental to the vehicle or occupants.
STARTING AND OPERATING 3. While still rolling, rotate the transfer case control switch to the desired position. 4. After the position indicator light has stopped flashing, shift the transmission back into gear. 4. After the position indicator light has stopped flashing, shift the transmission back into gear. NOTE: The ignition key must be ON for a shift to take place and for the position indicator lights to be operable.
STARTING AND OPERATING PARKING BRAKE The foot operated parking brake is positioned below the lower left corner of the instrument panel. To release the parking brake, pull the parking brake release handle. 217 Be sure the parking brake is firmly set when parked and the gear-shift lever is in PARK position.
STARTING AND OPERATING WARNING! • Always fully apply the parking brake when leaving your vehicle, or vehicle may roll and cause damage or injury. Also be certain to leave an automatic transmission in Park. Failure to do so may cause the vehicle to roll and cause damage or injury. • Be sure the parking brake is fully disengaged before driving, failure to do so can lead to brake failure and an accident. • Leaving children in a vehicle unattended is dangerous for a number of reasons.
STARTING AND OPERATING The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure. The pump motor makes a low humming noise during operation, which is normal. The Anti-Lock Brake system includes an amber (ABS) warning light. When the light is illuminated, the AntiLock Brake system is not functioning. The system reverts to standard non-anti-lock brakes. Turning the ignition Off and On again may reset the Anti-Lock Brake system if the fault detected was only momentary.
STARTING AND OPERATING WARNING! • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING ROCKING THE VEHICLE If vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between FIRST and REVERSE, while applying slight pressure to the accelerator. 221 TIRE SAFETY INFORMATION Tire Markings The least amount of accelerator pedal pressure to maintain the rocking motion without spinning the wheels or racing the engine is most effective.
STARTING AND OPERATING • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter 9P9 is absent from this tire size designation. Example: 215/65R15 96H • Temporary Spare tires are high pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
STARTING AND OPERATING 223 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards (....blank....( = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (ie. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. 225 Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: Some vehicles have a “Tire and Loading Information” placard located on the driver’s side “B” pillar. This placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires.
STARTING AND OPERATING 227 Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
STARTING AND OPERATING 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load carry capacity of your vehicle. 6.
STARTING AND OPERATING 229 5
STARTING AND OPERATING WARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 231 maximum loaded vehicle condition. These pressure conditions will be found in the “Supplemental Tire Pressure Information” section of this manual. 3.
STARTING AND OPERATING check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are underinflated. Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. CAUTION! Tire pressures change by approximately 1 psi (7 kPa) per 12° F (7° C) of air temperature change.
STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high speed vehicle operation.
STARTING AND OPERATING Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Always use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels). Never combine them with other types of tires. Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
STARTING AND OPERATING Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result.
STARTING AND OPERATING WARNING! WARNING! The limited use spare tires are for emergency use only. Installation of this limited use spare tire affects vehicle handling. With this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly. Replace (or repair) the original tire at the first opportunity and reinstall it on your vehicle.
STARTING AND OPERATING These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point. 237 Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that Replacing original tires with tires of a different size may result in false speedometer and odometer readings. specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.
STARTING AND OPERATING Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. SUPPLEMENTAL TIRE PRESSURE INFORMATION A light load vehicle condition is defined as two passengers {150 lbs (68 kg) each} plus 200 lbs (91kg) of cargo.
STARTING AND OPERATING These cautions apply to all chain traction devices, including link and cable (radial) chains. Tire chain use is permitted only on the rear tires of Durango trucks. NOTE: The use of class “S” chains is permitted on Durangos with P245/70R17 tires. CAUTION! Do not use tire chains on 4x4 Durango trucks equipped with P265/65R17 tires. There may not be adequate clearance for the chains and you are risking structural or body damage to your vehicle.
STARTING AND OPERATING 241 TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates and tend to develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all season type tires.
STARTING AND OPERATING FUEL REQUIREMENTS All engines (except 5.7L engines) are designed to meet all emissions regulations and provide excellent fuel economy and performance when using high quality unleaded “regular” gasoline having an ocAll Engines tane rating of 87. The routine use of preExcept 5.7L mium gasoline is not recommended. Under normal conditions the use of premium fuel will not provide a benefit over high quality regular gasolines and in some circumstances may result in poorer performance.
STARTING AND OPERATING and durability for your vehicle. We recommend the use of gasolines that meet the WWFC specifications if they are available. Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasolines contain oxygenates, and are specifically blended to reduce vehicle emissions and improve air quality. We strongly support the use of reformulated gasolines.
STARTING AND OPERATING MMT In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasolines blended with MMT provide no performance advantage beyond gasolines of the same octane number without MMT. Gasolines blended with MMT reduce spark plug life and reduce emission system performance. We recommend that gasolines free of MMT be used in your vehicle.
STARTING AND OPERATING 245 CAUTION! CAUTION! If the Check Engine or Service Engine Soon light is flashing, immediate service is required; see onboard diagnostics system section. To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. Materials Added To Fuel All gasolines sold in the United States are required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in unnecessary cost.
STARTING AND OPERATING WARNING! CAUTION! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle or on a truck bed. You could be burned. Always place gas containers on the ground while filling. Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door.
STARTING AND OPERATING WARNING! • Remove the fuel tank filler tube cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury. • The volatility of some gasolines may cause a buildup of pressure in the fuel tank that may increase while you drive. This pressure can result in a spray of gasoline and/or vapors when the cap is removed from a hot vehicle. Removing the cap slowly allows the pressure to vent and prevents fuel spray.
STARTING AND OPERATING • When pulling a heavy load or driving a fully loaded vehicle when the humidity is low and the temperature is high, use a premium unleaded fuel to help prevent spark knock. If spark knock persists, lighten the load, or engine piston damage may result. • The use of fuel additives which are now being sold as octane enhancers is not recommended. Many of these products contain high concentrations of methanol.
STARTING AND OPERATING the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. CATALYTIC CONVERTER The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device.
STARTING AND OPERATING vehicle should be stopped, the engine shut off and the vehicle allowed to cool. Service, including a tune-up to manufacturer’s specifications should be obtained immediately. To minimize the possibility of catalyst damage: VEHICLE LOADING Certification Label As required by National Highway Traffic Safety Administration Regulations, your vehicle has a certification label affixed to the driver’s side door. • Do not try to start the engine by pushing or towing the vehicle.
STARTING AND OPERATING Rating (GAWR) front and rear, and Vehicle Identification Number (VIN). A Month-Day-Hour (MDH) number is included on this label and shows the Month, Day, and Hour of manufacture. The bar code that appears on the bottom of the label is your Vehicle Identification Number (VIN). Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options, and cargo.
STARTING AND OPERATING Inflation Pressure (Cold) This is the cold tire inflation pressure for your vehicle for all loading conditions up to full GAWR. Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle. The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.
STARTING AND OPERATING WARNING! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle. A loaded vehicle is shown in the following example. Note that neither GVWR nor GAWR capabilities are exceeded. Overloading can cause potential safety hazards and shorten service life.
STARTING AND OPERATING TRAILER TOWING To maintain warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing. Definitions The following trailer towing related terminology definitions will assist in understanding the subsequent sections: GROSS COMBINATION WEIGHT RATING (GCWR) is the total permissible weight of your vehicle and trailer when weighed in combination. (Note that GCWR ratings include a 68 kg (150 lb.
STARTING AND OPERATING Consider the following items when computing the weight on the rear axle: • The tongue weight of the trailer. • The weight of any other type of cargo or equipment put in or on your vehicle. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle.
STARTING AND OPERATING • Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs. (907 kg). • Use an approved trailer harness and connector. If a hitch is ordered, the proper wiring will be provided. • When hauling cargo or towing a trailer, do not overload your vehicle or trailer. Overloading can cause a loss of control, poor performance or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure or tires.
STARTING AND OPERATING 257 Gross Combined Vehicle Weight Rating (GCWR) The Gross Combined Vehicle Weight Rating (GCWR) is the MAXIMUM allowable weight of the towing vehicle, including passengers and cargo, and the weight of the loaded trailer. Calculate the maximum trailer weight (MTW) by subtracting the towing vehicle’s weight, including passengers, and cargo from GCWR. Trailer sway control and equalizing hitch are required for tongue weights above 350 lbs. (159 kg).
STARTING AND OPERATING • Total weight must be distributed between the tow vehicle and the trailer such that the following four (4) ratings are not exceeded: 1. GVWR 2. GTW 3. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight.) 4.
STARTING AND OPERATING 259 outside lamp/bulb failure. Therefore, an occasional visual check around the vehicle is recommended. Once the trailer is removed the above indication will return to the vehicle. Heavy trailer towing also may require breakaway electric trailer brakes, anti-sway devices or equalizing hitches for safe operation. Such devices are commonly required by state law.
STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 7 - Pin Connector 4 - Pin Connector Cooling System Tips—Trailer Towing To reduce potential for engine and transmission overheating, take the following actions: • City Driving When stopped for short periods of time, put transmission in neutral and increase engine idle speed.
STARTING AND OPERATING • Highway Driving Reduce speed. • Air Conditioning Turn off temporarily. • See Cooling System Operating information in the Maintenance section of this manual for more information. To reduce potential for automatic transmission overheating, turn the “TOW/HAUL” feature on when driving in hilly areas or shift the transmission to Drive position 2 on more severe grades. Move the shift lever to the next lower position to eliminate excessive transmission shifting.
STARTING AND OPERATING CAUTION! Using this vehicle for snowplow applications can cause damage to the vehicle. WARNING! Attaching a snowplow to this vehicle could adversely affect performance of the airbag system in an accident. Do not expect that the airbag will perform as described earlier in this manual RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
STARTING AND OPERATING 263 CAUTION! CAUTION! Internal damage to the transfer case will occur if a front or rear wheel lift is used when recreational towing. It is necessary to follow these steps to be certain that the transfer case is fully in Neutral (N) before recreational towing to prevent damage to internal parts. NOTE: The NV 244 Generation II transfer case must be shifted into Neutral (N) for recreational towing.
STARTING AND OPERATING 7. After shift is completed and the Neutral (N) light comes on release Neutral (N) button. 8. Start engine. 9. Shift automatic transmission into Reverse (R). 10. Release brake pedal for five seconds and ensure that there is no vehicle movement. 11. Repeat steps 9 and 10 with the transmission in Drive (D). 12. Shut engine OFF and place ignition key to the unlocked OFF position. 13. Shift automatic transmission into Park (P). 14. Attach vehicle to tow vehicle with tow bar.
STARTING AND OPERATING CAUTION! Damage to the transmission may occur if the transmission is shifted into Park (P) with the transfer case in Neutral (N) and the engine RUNNING. With the transfer case in Neutral (N) ensure that the engine is OFF prior to shifting the transmission into Park (P) Shifting OUT of Neutral (N) Use the following procedure to prepare your vehicle for normal usage. 1. Bring vehicle to a complete stop. 2. Shut engine OFF. 3. Place ignition key in the ON position. 4.
STARTING AND OPERATING the 1 second time, then all of the position indicator lights will flash continuously until all requirements are met or until the Neutral (N) button is released. NOTE: The ignition key must be ON for a shift to take place and for the position indicator lights to be operable. If the key is not On, the shift will not take place and no position indicator lights will be on or flashing.
STARTING AND OPERATING TRACTION When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observed: 1. Slow down during rainstorms or when roads are slushy. 2. Slow down if road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible.
WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 270 ▫ Tire Changing Procedure . . . . . . . . . . . . . . . . 275 m Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 270 m Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 280 m Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . 272 m Towing A Disabled Vehicle . . . . . . . . . . . . . . . . 282 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is on the top of the steering column, just behind the steering wheel. Press the flasher switch and all front and rear directional signals will flash intermittently. Press the switch a second time to turn off the emergency flashers. This is an emergency warning system and should not be used when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists.
WHAT TO DO IN EMERGENCIES 271 WARNING! WARNING! A fire may result if gasoline is pumped into a portable container that is in a vehicle or on a truck bed. You could be burned. Always place gas containers on the ground while filling. Remove the gas cap slowly to prevent fuel spray from the filler neck which may cause injury. The volatility of present gasolines may cause a build up of pressure in the fuel tank that may increase while you drive.
WHAT TO DO IN EMERGENCIES CHANGING A FLAT TIRE Jack Location In the Durango, the scissor jack and tire changing tools are stowed under the second row seat. The jack is secured in place with a winged stud and a fixed stud. It is very important to secure the jack tightly in place by engaging the slot in the base to the fixed stud under the middle seat. The winged stud inserts through the eyelet in the end of the jack’s worm screw.
WHAT TO DO IN EMERGENCIES WARNING! The jack is designed as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes, unless suitable supports are placed under the vehicle as a safety measure. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. 273 Removing The Spare Tire The spare tire on the Dodge Durango is located underneath the vehicle in the rear.
WHAT TO DO IN EMERGENCIES Remove the spare tire before attempting to jack the truck. 1. Remove the rubber plug from the floor in the cargo area. 3. Turn the wrench counterclockwise to lower the spare tire. Continue to turn the wrench until the spare tire can be pulled out from under the vehicle. It is recommended that you stow the flat or spare to avoid tangling the loose cable. CAUTION! The winch mechanism is designed for use with the jack extension tube only.
WHAT TO DO IN EMERGENCIES Tire Changing Procedure WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. Do not raise this vehicle using a bumper jack.
WHAT TO DO IN EMERGENCIES • Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. 4. When changing a front wheel, place the jack under the frame rail behind the wheel. Locate the jack as far forward as possible on the straight part of the frame (prior to inboard transition.
WHAT TO DO IN EMERGENCIES 277 When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle as close to the tire as posssible with the drive tubes extending to the rear. Connect the jack tube extension and wheel wrench. 6 Rear Right Jacking Location Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required.
WHAT TO DO IN EMERGENCIES WARNING! WARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Always stow the jack, tools and the extra tire and wheel in the places provided. 6. Remove the wheel nuts and pull the wheel off.
WHAT TO DO IN EMERGENCIES WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised. • Apply the parking brake firmly before jacking. • Never start the engine with the vehicle on a jack. • Do not let anyone sit in the vehicle when it is on a jack.
WHAT TO DO IN EMERGENCIES JUMP STARTING WARNING! • Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush the contaminated area immediately with large quantities of water. • A battery generates hydrogen gas which is flammable and explosive. Keep flame or spark away from the vent holes.
WHAT TO DO IN EMERGENCIES 4. Connect one end of a jumper cable to the positive terminal of the booster battery. Connect the other end of the same cable to the positive terminal of the discharged battery. WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result. 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery.
WHAT TO DO IN EMERGENCIES WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle. TOWING A DISABLED VEHICLE Proper towing or lifting equipment is required to prevent damage to your vehicle. Use of safety chains is recommended.
MAINTAINING YOUR VEHICLE CONTENTS m Engine Compartment 3.7L V6 . . . . . . . . . . . . . . 286 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 292 m Engine Compartment 4.7L V-8 . . . . . . . . . . . . . . 287 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . . 297 m Engine Compartment 5.7L HEMI V-8 . . . . . . . . . 288 ▫ Drive Belts — Check Condition And Tension . . 297 m Onboard Diagnostic System — OBD II . . . . . . . . 289 ▫ Spark Plugs . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Air Conditioner Maintenance . . . . . . . . . . . . . 302 ▫ Axles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319 ▫ Power Steering — Fluid Check . . . . . . . . . . . . 303 ▫ Selection Of Lubricating Grease . . . . . . . . . . . 320 ▫ Front Suspension Ball Joints . . . . . . . . . . . . . . 304 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 ▫ Drive Shaft Constant Velocity Joints . . . . . . . .
MAINTAINING YOUR VEHICLE 285 ▫ Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 335 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337 m Fluids And Capacities . . . . . . . . . . . . . . . . . . . 335 ▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338 m Recommended Fluids, Lubricants And Genuine Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT 3.
MAINTAINING YOUR VEHICLE 287 ENGINE COMPARTMENT 4.
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT 5.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing.
MAINTAINING YOUR VEHICLE 291 the key is turned off. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL symbol is on with the engine running. b. The MIL light will remain fully illuminated until the first engine crank or the key is turned off. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station.
MAINTAINING YOUR VEHICLE NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. WARNING! Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance.
MAINTAINING YOUR VEHICLE 293 1. Position the vehicle on a level surface. 2. Turn Off the engine and allow approximately 5 minutes for the oil to settle to the bottom of the crankcase. 3. Remove the engine oil level indicator (dipstick). 4. Wipe the engine oil level indicator (dipstick) clean. 5. Install the engine oil level indicator (dipstick) and make sure it is seated in the tube. 6.
MAINTAINING YOUR VEHICLE Frequency Of Oil Change Road conditions and your style of driving affect the interval at which your oil should be changed. Check the following to determine if ANY apply to you: • Day or night temperatures are below 32°F (0°C). • Stop and Go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16.2 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C).
MAINTAINING YOUR VEHICLE This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacture only recommends API Certified engine oils that meet the requirements of DaimlerChrysler Material Standard MS-6395. Use Mopar or an equivalent oil meeting the specifi- periodically. Make sure that these units are always clean. This will tend to reduce to a minimum the amount of abrasive material that may enter the engine.
MAINTAINING YOUR VEHICLE used provided that the oil quality requirements described above are met and the recommended maintenance intervals for oil and filter changes are followed. • Lubricants which do not have both the engine oil certification mark or current service symbol and the correct viscosity grade number should not be used. Synthetic Engine Oils There are a number of engine oils being promoted as either synthetic or semi-synthetic.
MAINTAINING YOUR VEHICLE governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Engine Oil Filter Selection The manufacturer’s engines have a full-flow type oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high quality filters should be used to assure most efficient service.
MAINTAINING YOUR VEHICLE due to a faulty spark plug. Check the Vehicle Emissions Control Information label for the proper type of spark plug for your vehicle. CAUTION! When replacing plugs, do not overtighten. You could damage them and cause them to leak. Ignition Cables Replace the ignition cables (5.7L engines only) at the mileage interval shown in the maintenance charts. Engine Air Cleaner Filter Under normal driving conditions, replace the air filter at the intervals shown on Schedule “A”.
MAINTAINING YOUR VEHICLE Engine Fuel Filter A plugged fuel filter can cause stalling, limit the speed at which a vehicle can be driven or cause hard starting. Should an excessive amount of dirt accumulate in the fuel tank, frequent filter replacement may be necessary. Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device.
MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may indicate severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds. Always wash hands after handling the battery. 301 To determine the battery charge, check the battery test indicator (if equipped) on top of the battery. Refer to the illustration. CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.
MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system.
MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
MAINTAINING YOUR VEHICLE Front Suspension Ball Joints The ball joints and seals should be inspected whenever the vehicle is serviced for other reasons. Damaged seals should be replaced to prevent leakage or contamination of the grease. Drive Shaft Constant Velocity Joints All four wheel drive models are equipped with four constant velocity joints. Periodic lubrication of these joints is not required. However, the joint boot should be inspected for external leakage or damage periodically.
MAINTAINING YOUR VEHICLE Windshield Wiper Blades The rubber edges of the wiper blades and the windshield should be cleaned periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield.
MAINTAINING YOUR VEHICLE freezing the fluid on the cold windshield. Mopart All Weather Windshield Washer Solution used with water as directed on the container, aids cleaning action, reduces freezing point to avoid line clogging, and is not harmful to paint or trim. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
MAINTAINING YOUR VEHICLE 307 bugs, leaves, etc. If dirty, clean the radiator core by gently spraying water from a garden hose at the back of the core. WARNING! Check the coolant bottle tubing for condition and tightness of connection at coolant bottle and radiator. Inspect the entire system for leaks. You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood don’t open the hood until the radiator has had time to cool.
MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush And Refill If the solution is dirty and contains a considerable amount of sediment, it should be cleaned and flushed. See your authorized dealer for proper draining, flushing and refilling of your vehicle’s cooling system. Disposal of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community.
MAINTAINING YOUR VEHICLE CAUTION! Mixing of coolants other than specified (nonHOAT), may result in engine damage that may not be covered under the new vehicle warranty, and decreased corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible. Do not use plain water alone or alcohol base antifreeze products.
MAINTAINING YOUR VEHICLE WARNING! WARNING! Never add coolant to the radiator when the engine is overheated. Do not loosen or remove pressure cap to cool overheated engine. The coolant is under pressure and severe scalding could result. The warning words “DO NOT OPEN HOT” on the coolant pressure cap are a safety precaution. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap when the system is hot or under pressure.
MAINTAINING YOUR VEHICLE The radiator normally remains completely full, so there is no need to remove the pressure cap except checking coolant freeze point or replacement with new antifreeze coolant. Your service attendant should be advised of this. When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember A. Do not overfill the coolant bottle. B. Check coolant freeze point in the radiator and in the coolant bottle.
MAINTAINING YOUR VEHICLE swelling suggest deterioration of the rubber. Particular attention should be given to examining hose surfaces nearest to high heat sources, such as the exhaust manifold. specification, in any fuel system servicing. It is mandatory to replace all clamps that have been loosened or removed during service. Care should be taken in installing new clamps to insure they are properly torqued. Insure nylon tubing in these areas has not melted or collapsed.
MAINTAINING YOUR VEHICLE 313 Brake Master Cylinders The fluid level in the master cylinders should be checked whenever the vehicle is serviced, or immediately if the brake system warning light is on. If necessary, add fluid to bring level to the full mark on the side of the reservoir of the brake master cylinder. Be sure to clean the top of the master cylinder area before removing the cap. With disc brakes, fluid level can be expected to fall as the brake pads wear.
MAINTAINING YOUR VEHICLE WARNING! CAUTION! Use of brake fluid that may have a lower initial boiling point, or is unidentified, as to specifications may result in sudden brake failure during hard prolonged braking. You could have an accident. Do not allow a petroleum-base fluid to contaminate the brake fluid. Seal damage may result. WARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching on fire.
MAINTAINING YOUR VEHICLE WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any sign of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Automatic Transmission Fluid Level Check – 3.7L Engine This fluid level should be checked when the engine is fully warmed up and the fluid in the transmission is heated to its normal operating temperature.
MAINTAINING YOUR VEHICLE 5. Remove the dipstick and feel if the fluid is hot or warm. Hot fluid is approximately 180°F (82°C), the normal operating temperature after the vehicle has been driven at least 15 miles (24 km). The fluid cannot be comfortably held between the finger tips. Warm is when fluid is between 85° and 125°F (29° and 52°C). 6. Wipe the dipstick clean and reinsert until seated. Remove dipstick and note reading. a.
MAINTAINING YOUR VEHICLE 4. Place the gear selector momentarily in each gear position ending with the lever in P (Park). 5. Remove the dipstick, wipe it clean and reinsert it until seated. 6. Remove the dipstick again and note the fluid level on both sides. The fluid level should be between the “HOT” (upper) reference holes on the dipstick at normal operating temperature. Verify that solid coating of oil is seen on both sides of the dipstick. If the fluid is low, add as required into the dipstick tube.
MAINTAINING YOUR VEHICLE dipstick cap to spring back slightly from its fully seated position, as long as its seal remains engaged in the dipstick tube. Automatic Transmission Fluid And Filter Change To obtain best performance and long life for automatic transmissions, the manufacturer recommends that they be given regular maintenance service by an Authorized Dodge Dealer or Service Center.
MAINTAINING YOUR VEHICLE Transfer Case Inspect the transfer case for fluid leaks. If a fluid leak is evident the transfer case fluid level may be low. Have the transfer case serviced immediately. CAUTION! Damage may result from operation of the vehicle with low transfer case fluid. The transfer case fluid should be drained and refilled at the intervals specified. Lubricant Selection Refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE Front Axle Front Axle fluid level should be at the bottom of the filler hole plug. Selection of Lubricating Grease The National Lubricating Grease Institute (NLGI) has developed a symbol (Certification Mark) to aid the vehicle owner in the proper selection of grease for chassis components. This symbol, an example shown below, is located on the grease container and identifies the application and quality of the grease.
MAINTAINING YOUR VEHICLE Appearance Care and Protection from Corrosion The most common causes are: Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
MAINTAINING YOUR VEHICLE • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.
MAINTAINING YOUR VEHICLE • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use Mopart touch up paint on scratches as soon as possible. Your dealer has touch up paint to match the color of your vehicle. Interior Care Use Mopart Fabric Cleaner to clean fabric upholstery and carpeting.
MAINTAINING YOUR VEHICLE Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters or windshields equipped with a windshield wiper de-icer. Do not use scrapers or other sharp instruments which may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using.
MAINTAINING YOUR VEHICLE POWER DISTRIBUTION CENTER (FUSE/RELAY) Your vehicle is equipped with two electrical power distribution centers located next to each other in the left side of the engine compartment. Thess power distribution centers house new plug-in “Maxi” fuses which replace all the in-line fusible links previously used. The power distribution centers also contain “Mini”fuses and plug-in “ISO” relays.
MAINTAINING YOUR VEHICLE CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it suggests a problem in the circuit that must be corrected. NOTE: If you are leaving your vehicle dormant for longer than 21 days you may want to take steps to protect your battery.
MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS Dome Light . . . . . . . . . . . . . . . . . . . . . . . . WL212–2 Liftgate Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . 567 Overhead Console Lights . . . . . . . . . . . . . PLW214–2A Reading Light . . . . . . . . . . . . . . . . . . . . . . . WL212–2 Visor Vanity Lights . . . . . . . . . . . . . . . Not Serviceable LIGHT BULBS — Outside Bulb No. Headlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 2. Remove one nut that attaches the headlight to the inner fender panel. Access to the nut is possible by removing the fender panel access door which is located in the wheel liner. 3. Grasp the headlight and pull firmly to disengage the headlight from the fender panel. 4. While firmly holding the headlight in your hands disconnect all connectors by following the procedure described in step number 5 below. 5.
MAINTAINING YOUR VEHICLE 329 Rear Side Marker, Tail Lights, Turn Signals And Backup Lights — Replacement 1. Remove the two push-pins from the tail light housing.
MAINTAINING YOUR VEHICLE 2. Rotate the light to the outboard side of the vehicle and remove. 3. Unlock and remove electrical connector.
MAINTAINING YOUR VEHICLE 4. Remove the three screws holding the bulb strip to the back of the tail light lens. 331 5. Remove the bulb strip from the tail light lens.
MAINTAINING YOUR VEHICLE 6. Remove bulbs from bulb strip by pulling the bulb straight out.
MAINTAINING YOUR VEHICLE License Lights 333 2. Rotate the socket 1/4 turn counterclockwise. 1. Remove the two screws securing the lens to the liftgate. 3. Pull bulb from socket.
MAINTAINING YOUR VEHICLE Center High-Mounted Stoplight 1. Remove two screws securing stoplight housing assembly to the liftgate. 3. Pull bulb straight from socket to remove. 2. Turn socket 1/4 counterclockwise and free from housing.
MAINTAINING YOUR VEHICLE Fog Lights 1. Rotate bulb and connector 1/4 turn counterclockwise. 335 NOTE: For foglights ensure that the takeout pushfasteners are relocated back in their positions; one in the foglight molding and the other in the hydroform. 2. Pull bulb off of connector. FLUIDS AND CAPACITIES U.S. Metric 27 Gal. 27 Gal 102L 102L 5 Qt. 6 Qt. 7 Qt. 4.7L 5.7L 6.6L 13.5 Qt. 12.9L Fuel 3.7L/4.7L, 87 Octane 5.7L, 89 Octane Engine Oil (with filter) 3.7L, SAE 5W-30, API Certified 4.
MAINTAINING YOUR VEHICLE 3.7L with Rear Heat (Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula) 4.7L without Rear Heat (Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula) 4.7L with Rear Heat (Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula) 5.7L without Rear Heat (Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula) 5.7L with Rear Heat (Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula) NOTE: All fluid capacities are approximate capacities. U.S. Metric 14.5 Qt. 13.8L 13.1 Qt.
MAINTAINING YOUR VEHICLE 337 RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection 3.7L/4.7L Fuel Selection 5.7L Fluids, Lubricants and Genuine Parts Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) P/N 5011764AB or equivalent. Use SAE 5W-30, API Certified, meeting material standard MS-6395. Mopart Engine Oil Filter, P/N 5281090 or equivalent.
MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Transfer Case Front Axle Rear Axle Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopart ATF+4, Automatic Transmission Fluid. Mopart ATF+4, Automatic Transmission Fluid. SAE 75W-90 Multipurpose Type, GL-5 Gear Lubricant. SAE 75W-140 Synthetic Gear Lubricant. Mopart DOT 3 and SAE J1703 should be used. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E m Emission Control System Maintenance . . . . . . . . 340 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 343 m Emissions Testing . . . . . . . . . . . . . . . . . . . . . . . 340 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . . 353 C m Maintenance Schedules . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 340 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type on the following pages must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and S reliability.
MAINTENANCE SCHEDULES MAINTENANCE SCHEDULES There are two maintenance schedules that show the required service for your vehicle. First is Schedule “B”. It is for vehicles that are operated under the conditions that are listed below and at the beginning of the schedule. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km).
M 342 MAINTENANCE SCHEDULES A I N CAUTION! T E Failure to perform the required maintenance items N may result in damage to the vehicle. A N C E At Each Stop for Fuel S C H E D U L E S 8 • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accuracy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark. • Check the windshield washer solvent and add if required.
SCHEDULE “B” Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90° F (32° C). 343 M A I N • Taxi, police, or delivery service (commercial service).
M 344 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Rotate tires. N C Change rear axle fluid. E Change front axle fluid (4X4). S C H E D U L E S 8 Inspect engine air cleaner filter, replace if necessary.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.* Drain and refill automatic transmission fluid and change main sump filter (4.7L/5.7L only).
M 346 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Rotate tires. N C Change rear axle fluid. E Change front axle fluid (4X4). S C H E D U L E S 8 Inspect brake linings. Inspect engine air cleaner filter, replace if necessary.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.* Inspect and replace ignition cables if necessary (5.7L only). Inspect auto tension drive belt and replace if required. Drain and refill automatic transmission fluid, change filter (3.7L).
M 348 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Rotate tires. N C Change rear axle fluid. E Change front axle fluid (4X4). S C H E D U L E S 8 Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Inspect auto tension drive belt and replace if required.
SCHEDULE “B” Miles (Kilometers ) Change engine oil and engine oil filter. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.* Inspect auto tension drive belt and replace if required. Drain and refill automatic transmission fluid and change main sump and cooler return filter (if equipped) (4.7L/5.7L only).
M 350 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Rotate tires. N C Flush and replace engine coolant. E Change rear axle fluid. S C H E D U L E S 8 Change front axle fluid (4X4).
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect and replace ignition cables if necessary (5.7L only). Inspect PCV valve, replace as necessary.* Inspect auto tension drive belt and replace if required.‡ Drain and refill transfer case fluid (4X4).
M 352 SCHEDULE “B” A I N Miles T (Kilometers) E N Drain and refill automatic transmission fluid, A change filter (3.7L). This applies only if your N vehicle is used for police, taxi, fleet, or trailer C towing. E S C H E D U L E S 8 105,000 (168 000) Drain and refill automatic transmission fluid and change main sump filter (4.7L/5.7L only). * This maintenance is recommended by the manufacture to the owner but is not required to maintain the emissions warranty.
SCHEDULE “A” 353 M Schedule “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check transfer case fluid level (4X4). Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs.
M 354 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Check transfer case fluid level (4X4). S C H E D U L E S 8 Flush and replace engine coolant at 60 months, regardless of mileage. Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. Inspect PCV valve, replace as necessary. * Inspect and replace ignition cables if necessary (5.7L only). Inspect auto tension drive belt and replace if required.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check transfer case fluid level (4X4). Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. Inspect PCV valve, replace as necessary.* Inspect auto tension drive belt and replace if required.‡ Drain and refill automatic transmission fluid and change sump and cooler return filter (if equipped) (4.7L/5.7L only).
M 356 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Drain and refill tranfer case fluid (4X4). S C H E D U L E S 8 Flush and replace engine coolant, if not done at 60 mos. Flush and replace engine coolant, if not done at 102,000 miles (163 000 km) Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. Inspect PCV valve, replace as necessary.
SCHEDULE “A” Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts. 357 M WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360 ▫ Prepare For The Appointment . . . . . . . . . . . . 360 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 360 ▫ Be Reasonable With Requests . . . . . . . . . . . . . 360 m If You Need Assistance . . . . . . . . . . . . . . . . . . . 360 m Warranty Information . . . . . . . . . . . . . . . . . . . . 363 m Mopart Parts . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE The manufacturer has empowered its dealers to make warranty and repair decisions that ensure you are not inconvenienced. There is no need for you to wait for a decision from the manufacturer. If a special circumstance occurs that requires information from the manufacturer, we have asked the dealer’s service management to make the contact on your behalf. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process.
IF YOU NEED CONSUMER ASSISTANCE In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico (915) 729–1248 or 729–1240 Outside Mexico (525) 729–1248 or 729–1240 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center.
IF YOU NEED CONSUMER ASSISTANCE Contract, and you require service after your manufacturer’s new vehicle limited warranty expires, please refer to your contract documents, and contact the person listed in those documents. We appreciate that you have made a major investment when you purchased your new vehicle. Your dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with your ownership experience.
IF YOU NEED CONSUMER ASSISTANCE
IF YOU NEED CONSUMER ASSISTANCE MOPART PARTS Mopart fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.
IF YOU NEED CONSUMER ASSISTANCE • Owner’s Manuals. These manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler group vehicles. Included are starting, operating, emergency and maintenance procedures as well as specifications, capabilities and safety tips. 367 Call Toll Free at 1–800–890–4038 (U.S.) or 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: www.techauthority.daimlerchrysler.com or www.daimlerchrysler.
INDEX 10
INDEX Adding Engine Coolant (Antifreeze) . . . . . . . . . . 309 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . 245,270 Air Cleaner, Engine . . . . . . . . . . . . . . . . . . . . . . 298 Air Conditioner Maintenance . . . . . . . . . . . . . . . 302 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 184 Air Conditioning Controls . . . . . . . . . . . . . . . . . 184 Air Conditioning Refrigerant . . . . . . . . . . . . . 302,303 Air Conditioning System . . . . . . . . . . . .
INDEX Axle Lubrication . . . . . . . . . . . . . . . . . . . . . . . . 319 Ball Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280 Emergency Starting . . . . . . . . . . . . . . . . . . . . . 280 Gas Caution . . . . . . . . . . . . . . . . . . . . . . . . . . 280 Keyless Transmitter Replacement . . . . . . . . . . . . 24 Saving Feature . . . . . .
INDEX Center High Mounted Stop Light . . . . . . . . . . . . 334 Certification Label . . . . . . . . . . . . . . . . . . . . . . . 250 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . . 272 Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280 Chart, Tire Sizing . . . . . . . . . . . . . . . . . . . . . . . . 223 Child Restraint . . . . . . . . . . . . . . . . . . . . . . 50,51,61 Child Restraint Tether Anchors . . . . . . . . . . . . .
INDEX Daytime Running Lights . . . . . . . . . . . . . . . . . . . 107 Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . . . 291 Defroster, Rear Window . . . . . . . . . . . . . . . . . . . 195 Defroster, Windshield . . . . . . . . . . . . . . . . 63,182,187 Delay Wipers . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Diagnostic System, Onboard . . . . . . . . . . . . . . . . 289 Dimmer Switch, Headlight . . . . . . . . . . . . . . . . . 147 Dipsticks Automatic Transmission . . . . .
INDEX Exhaust Gas Caution . . . . . . . . . . . . . . . . . . 62,248 Fails to Start . . . . . . . . . . . . . . . . . . . . . . . . . . 201 Flooded, Starting . . . . . . . . . . . . . . . . . . . . . . 201 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . 335 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 280 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 292,335,337 Oil Selection . . . . . . . . . . . . . . . . . . . . . . . . . . 335 Oil Synthetic . . . . . . .
INDEX Transfer Case . . . . . . . . . . . . . . . . . . . . . . . . . 319 Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 107,335 Folding Rear Seat . . . . . . . . . . . . . . . . . . . . . . 91,93 Four Wheel Drive . . . . . . . . . . . . . . . . . . . . . . . 208 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 Four-Way Hazard Flasher . . . . . . . . . . . . . . . . . . 270 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . . 221 Front Axle . . . . . . . . . . .
INDEX Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327 Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 High Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 High Beam/Low Beam Select Switch . . . . . . . . 109 Lights On Reminder . . . . . . . . . . . . . . . . . . . . 107 Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 Replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327 Heated Mirrors . . . . . . . . . .
INDEX Key, Replacement . . . . . . . . . . . . . . . . . . . . . . . . 10 Key, Sentry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Key-In Reminder . . . . . . . . . . . . . . . . . . . . . . . . . 9 Keyless Entry System . . . . . . . . . . . . . . . . . . . . . . 19 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Knee Bolster . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Lane Change and Turn Signals . . . . . . . . . 108,146,329 Lap/Shoulder Belts .
INDEX Turn Signal . . . . . . . . . . . . . . . . . . . . . . . . 108,329 Warning (Instrument Cluster Description) . . . . . 146 Washer Fluid . . . . . . . . . . . . . . . . . . . . . . . . . 153 Loading Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 250 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226 Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Auto Unlock . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Automatic Door . . . . . .
INDEX Rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Vanity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Modifications/Alterations, Vehicle . . . . . . . . . . . . . 6 Mopar Parts . . . . . . . . . . . . . . . . . . . . . . . . . 291,365 Multi-Function Control Lever . . . . . . . . . . . . . . . 108 New Vehicle Break-In Period . . . . . . . . . . . . . . . . 62 Occupant Classification System . . . . . . . . . . . . . . . 42 Occupant Restraints . . . . . . . . . .
INDEX Pets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Pets, Transporting . . . . . . . . . . . . . . . . . . . . . . . . 61 Phone, Cellular . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Phone, Hands-Free . . . . . . . . . . . . . . . . . . . . . . . 74 Placard, Tire and Loading Information . . . . . . . . . 226 Positive Crankcase Valve . . . . . . . . . . . . . . . . . . 312 Power Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Reclining Front Seats . . . . . . . . . . . . . . . . . . . . . . 87 Recommended Fluids, Lubricants and Genuine Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337 Recreational Towing . . . . . . . . . . . . . . . . . . . . . . 262 Shifting into Transfer Case Neutral (N) . . . . . . . 263 Shifting out of Transfer Case Neutral (N) . . . . . 265 Reformulated Gasoline . . . . . . . . . . . . . . . . . . . . 243 Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . . 88 Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Reclining . . .
INDEX Emergency (Jump Starting) . . . . . . . . . . . . . . . 280 Engine Block Heater . . . . . . . . . . . . . . . . . . . . 202 Engine Fails to Start . . . . . . . . . . . . . . . . . . . . 201 Starting Procedures . . . . . . . . . . . . . . . . . . . . . . 200 Steering Column Controls . . . . . . . . . . . . . . . . . . . . . . 108 Column Lock . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . 220,303 Wheel, Tilt . . . . . . . . . . . . . .
INDEX Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275 Load Capacity . . . . . . . . . . . . . . . . . . . . . 226,227 Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 237 Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 221,230 Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 Snow Tires . . .
INDEX Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318,338 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 315 Transmitter Battery Service . . . . . . . . . . . . . . . . . . 24 Transmitter, Garage Door Opener . . . . . . . . . . . . 126 Transmitter Programming . . . . . . . . . . . . . . . . . . . 22 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . 236 Trip Computer . . . . . . . . . . .
INDEX Windshield Defroster . . . . . . . . . . . . . . . . 63,182,187 Windshield Washers . . . . . . . . . . . . . . . . 110,111,305 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110,305 Windshield Wiper Blades . . . . . . . . . . . . . . . . . . 305 Windshield Wipers . . . . . . . . . . . . . . . . . . . . . . . 110 Wiper Blade Replacement Wiper, Rear . . . . . . . . . . Wipers, Intermittent . . . . Wrecker Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .