TABLE OF CONTENTS SECTION PAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1 1 INTRODUCTION 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4 UNDERSTANDING YOUR INSTRUMENT PANEL 5 STARTING AND OPERATING 6 WHAT TO DO IN EMERGENCIES 7 MAINTAINING YOUR VEHICLE 8 MAINTENANCE SCHEDULES 9 IF YOU NEED CONSUMER ASSISTANCE 10 INDEX . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS m Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m Vehicle Identification Number . . . . . . . . . . . . . . 6 m How To Use This Manual . . . . . . . . . . . . . . . . . 4 m Vehicle Modifications / Alterations . . . . . . . . . . 6 m Warnings And Cautions . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . . 9 ▫ Automatic Transaxle Ignition Interlock System . .14 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . . 9 m Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . .14 ▫ Locking Doors With The Key . . . . . . . . . . . . . .10 ▫ Manual Door Locks . . . . . . . . . . . . . . . . . . . . .14 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Unlock The Trunk . . . . . . . . . . . . . . . . . . . .18 ▫ Adjustable Upper Shoulder Belt Anchorage . . . .28 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .18 ▫ Lap/Shoulder Belt Untwisting Procedure . . . . .29 ▫ Programming Additional Transmitters . . . . . . . .19 ▫ Seat Belts And Pregnant Women . . . . . . . . . . . .30 ▫ General Information . . . . . . . . . . . . . . . . . . . .19 ▫ Seat Belt Extender . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place. 9 Automatic Transaxle Place the shift lever in PARK and make sure that the shift knob push button has returned to the out position. Turn the key to the OFF position, turn to the lock position, and remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service. WARNING! Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector lever. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SENTRY KEY The Sentry Key Immobilizer System prevents unauthorized operation of the vehicle by disabling the engine. The system will shut the engine off after 2 seconds of running if an invalid key is used to start the vehicle. This system utilizes ignition keys which have an electronic chip (transponder) embedded into them. Only keys that have been programmed to the vehicle can be used to start and operate the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE All of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle. At the time of purchase, the original owner is provided with a four digit PIN number. This number is required for dealer replacement of keys.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Repeat this procedure to program up to a total of 8 keys. If you do not have a programmed sentry key, contact your dealer for details. General Information The Sentry Key system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Transaxle Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK and the shift knob push-button is fully released. It also prevents shifting out of PARK unless the key is in the ON/RUN or START positions and you have depressed the brake pedal. CAUTION! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unattended.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death. 15 Power Door Locks — If Equipped A power door lock switch is on each front door panel. Press this switch to lock or unlock the doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. A single chime will sound to signify that you have successfully disabled the double activation feature. You can turn the feature back on by repeating the above mentioned procedure. You can turn the feature back on by repeating the above mentioned procedure. Automatic Door Locks — If Equipped The doors will lock automatically if: 3. Press the interior door lock switch to the LOCK position. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Lock the Doors Press and release the LOCK button to lock all doors. The park/lamps will flash and the horn will chirp to acknowledge the signal. Horn Chirp Feature The horn chirp that signals that the doors have been locked can be toggled on or off by using the following procedure: 1. Insert the ignition key and turn the switch to the ON/RUN position. 2. Press and hold the UNLOCK button on the transmitter for 4 to 10 seconds. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Programming Additional Transmitters Up to four transmitters can be programmed to your vehicle. Your new vehicle was shipped with two transmitters. See your dealer for additional transmitters. Additional transmitters can be programmed to the system by using the following procedure: 1. Insert the key into the ignition and turn the switch to the RUN position. 2. Press and hold the UNLOCK button on the transmitter for between four and ten seconds. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. With the transmitter buttons facing down, use a thin coin or similar object to pry the two halves of the transmitter apart. Make sure not to damage the rubber gasket during removal. VEHICLE THEFT ALARM — IF EQUIPPED The system monitors the doors, trunk key cylinder, and ignition for unauthorized operation. If something triggers the alarm, the system will signal for about 18 minutes.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 3. The indicator light in the instrument cluster will flash rapidly for 16 seconds. This shows that the system is arming. During this period, if a door is opened, the ignition switch is turned on, or the power door locks are unlocked in any manner, the system will automatically disarm. If the light comes on but does not flash, the system is arming but there is a problem in the trunk circuit. After 16 seconds the indicator light will flash slowly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE INTERNAL EMERGENCY TRUNK LID RELEASE WARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat. If trapped in the trunk, children can die from suffocation or heat stroke.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE POWER WINDOWS — IF EQUIPPED The window switches on the driver’s door panel control both front windows. The switch on the passenger’s door panel controls the passenger’s window. 23 OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” WARNING! • A belt that is buckled into the wrong buckle will not protect you properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. 27 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 29 1. Position the latch plate as close as possible to the anchor point.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. At about 6 to 12 inches above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing. 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seats, and their covers are also labeled SRS AIRBAG. NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment. WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbags inflate in moderate to high speed impacts. Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4. If your vehicle has side airbags, do not lean against the door, airbags will inflate forcefully into the space between you and the door. WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Airbag System Components The front airbag system consists of the following: • Right and Left Side Impact Airbag Control Modules (SIACM) • Airbag Control Module (ACM) • Interconnecting Wiring • AIRBAG Readiness Light How The Airbag System Works Front Airbag System • Driver Airbag • Passenger Airbag • Steering Wheel and Column • Instrument Panel • Crash Sensor • Interconnecting Wiring • Knee Impact Bolsters The side airbag system, if equipped, consists of
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Airbag Control Module also turns on the AIRBAG light in the instrument panel for 6 to 8 seconds when the ignition switch is first turned to ON/RUN, then turns the light off. If it detects a malfunction in any part of the system, it turns on the light either momentarily or continuously. WARNING! Ignoring the AIRBAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 • The knee impact bolsters help protect the knees and position you for the best interaction with the front airbag. However, if you have not healed significantly within a few days, or if you have any blistering, see your doctor immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed airbags can’t protect you in another collision. Have the airbags replaced by an authorized dealer as soon as possible. Side Airbag System — If Equipped • The Side Impact Airbag Control Modules determine if a side collision is severe enough to require the airbag to inflate. The Side Impact Airbag Control Modules is not designed to detect roll over, front, or rear impacts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag Systems WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or frame.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children 12 years and under should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats, rather than in the front. WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may not work when you need it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the rear seat to install the child restraint. You will easily feel them if you run your finger along the intersection of the surfaces. The lower strap hooks are passed over the top of each bar, pushing aside the seat cover material. In addition, there are tether strap anchorages behind each rear seating position located in the panel between the rear seat back and the rear window — under a hinged plastic cover with this symbol on it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and remove slack in the tether strap according to the child restraint manufacturer’s instructions. WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Do not install child restraint systems equipped with LATCH attachments at all three rear seating positions at one time. The LATCH anchorages are designed to restrain no more than two child restraints at a time in the event of a collision. We urge that you carefully follow the directions of the manufacturer when installing your child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back. Transporting Pets Airbags deploying in the front seat could harm your pet.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 remain open, close all windows. Adjust the heating or cooling system to force outside air into the vehicle. Set the blower at high speed. SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defrosters Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 m Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 ▫ Folding Rear Seat . . . . . . . . . . . . . . . . . . . . . .57 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .51 m To Open And Close The Hood . . . . . . . . . . . . .58 ▫ Inside Compass/Temperature Mirror—If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 m Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Headlight Dimmer Switch . . . . . . . . . . . . . . . .62 ▫ To Set At A Desired Speed . . . . . . . . . . . . . . . .66 ▫ Passing Light . . . . . . . . . . . . . . . . . . . . . . . . .62 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . . .66 m Windshield Wipers And Washers . . . . . . . . . . .63 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . . .66 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustment. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lights • Briefly press the “Right” button to toggle the right reading lamp “ON/OFF”. Repeat the key press to cycle the light • Briefly press the “Left” button to toggle the left reading lamp “ON/OFF”. Repeat the key press to cycle the light. NOTE: The light can be activated with the ignition off. NOTE: The light(s) will automatically shut off after seven minutes with ignition off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 53 Compass Variance • Find your current location and determine the correct Zone number from the map. • Press and hold the “Left” button for 5–10 seconds (until “Zone” appears in the display), then release the button. The number displayed is the current Zone value. • If a new Zone value is desired, briefly press the “Left” button to increment the displayed value, (Range 1–15) until you find your desired Zone number.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass Calibration If “CAL” is not displayed, press and hold the “Left” button for 10–15 seconds, or until “CAL” appears in the display, then release the button. The compass is now in calibration mode. The mirror can be calibrated in one of two ways • Drive the vehicle in circles at less then 5mph (8 km/h) until “CAL” no longer appears in the display.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Select a mirror and press one of the four arrows for the direction you want the mirror to move. 55 SEATS Front Seat Adjustment The adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position. Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched after the adjustment bar is released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the restraints so that the upper edge is as high as practical. Push in on the release button to lower the head restraint. 57 Folding Rear Seat To provide additional storage area, the center of each rear seatback can be folded forward. Pull on the loops shown in the picture to fold down either or both seatbacks.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seatbelts • Be sure that everyone in your vehicle is in a seat and using a seatbelt properly. TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 59 Then lift the safety catch located under the front edge of the hood, near the center and raise the hood. 3 WARNING! Use the hood prop rod to secure the hood in the open position as shown. To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Front Map/Reading Lights — If Equipped These lights, located under the rearview mirror, can be turned on by means of switches located at the base of the rearview mirror. Interior Lights The interior lights come on when a door is opened. The interior lights will automatically turn off in about 8 minutes if a door is left open or the dimmer control is left in the Dome light position. Turn the ignition switch ON to restore the interior light operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dome Light Position Rotate the dimmer control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position. 61 lights, the passing lights, and fog lights. The lever is located on the left side of the steering column. Headlights, Parking Lights, Instrument Panel Lights Turn the end of the Multi-Function Control Lever to the first detent for parking light operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights (Canada Only) The front fog lights will come on as Daytime Running Lights whenever the ignition is on, the headlights are off, and the parking brake is off. The headlight switch must be used for normal night time driving. Lights-on Reminder If the headlights or parking lights are on after the ignition is turned OFF, a chime will sound when the driver’s door is opened.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch on the control lever. The lever is located on the right side of the steering column. Move the control lever up to select the desired wiper speed. 63 If the lever is pulled while in the OFF position, the wipers will operate for two wipe cycles, then turn OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE the end of the lever. Rotate the knob upward (clockwise) to decrease the delay time and downward (counterclockwise) to increase the delay time. The delay can be regulated from a maximum of approximately 18 seconds between cycles, to a cycle every second. Lo Speed Wipers Move the wiper stalk upward to the 2nd detent to obtain a low speed wiper function. Hi Speed Wipers Move the wiper stalk upward to the 3rd position to obtain the fastest wiper speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65 WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 25 mph (40 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it. To Set At A Desired Speed: When the vehicle has reached the desired speed, press down on the lever and release. Release the accelerator and the vehicle will operate at the selected speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Transaxle: Depressing the clutch pedal will disengage the speed control. A slight increase in engine RPM before the speed control disengages is normal. Vehicles equipped with manual transaxles may need to be shifted into a lower gear to climb hills without speed loss. WARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The sunroof control is located on the headliner between the sun visors. one second) to initiate the express open mode. During this operation, any movement of the switch will stop the sunroof and it will remain in a partial open position. To close the sunroof, hold the switch in the forward position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if so equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ash Receiver and Cigar Lighter When the Smoker’s Package is ordered from your authorized dealer, an ash receiver tray and a cigar lighter element are furnished. The lighter element can be inserted in the auxiliary power outlet. The ash receiver fits snugly in a cupholder position. To clean the ash receiver, lift it from the cupholder.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS m Instrument Panel Features . . . . . . . . . . . . . . . .74 ▫ AM Reception . . . . . . . . . . . . . . . . . . . . . . . .84 m Standard Instrument Cluster . . . . . . . . . . . . . . .75 ▫ FM Reception . . . . . . . . . . . . . . . . . . . . . . . . .84 m Optional Instrument Cluster . . . . . . . . . . . . . . .76 m Sales Code RBB—AM/FM Stereo Radio With Cassette Tape Player And CD Changer Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Fade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86 ▫ Bass And Treble Tone Control . . . . . . . . . . . . .86 ▫ AM/FM Selection . . . . . . . . . . . . . . . . . . . . . .86 ▫ Mode Button . . . . . . . . . . . . . . . . . . . . . . . . .86 ▫ Cassette Player Features . . . . . . . . . . . . . . . . .86 ▫ CD Changer Control Capability — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .87 ▫ Radio Display Messages . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 73 ▫ Playing Discs . . . . . . . . . . . . . . . . . . . . . . . . .99 m Compact Disc Maintenance . . . . . . . . . . . . . . . 101 ▫ Seek Button . . . . . . . . . . . . . . . . . . . . . . . . . 100 m Radio Operation And Cellular Phones . . . . . . . 102 ▫ FF/Tune/RW . . . . . . . . . . . . . . . . . . . . . . . . 100 m Climate Controls . . . . . . . . . . . . . . . . . . . . . . 102 ▫ Mode Button . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES
UNDERSTANDING YOUR INSTRUMENT PANEL 75 STANDARD INSTRUMENT CLUSTER 4
UNDERSTANDING YOUR INSTRUMENT PANEL OPTIONAL INSTRUMENT CLUSTER
UNDERSTANDING YOUR INSTRUMENT PANEL 77 OPTIONAL INSTRUMENT CLUSTER — R/T MODEL 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Front Fog Light Indicator — If Equipped This light shows when the front fog lights are ON. 2. Brake System Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light comes on, it may indicate that the parking brake is applied, or there is a low brake fluid level.
UNDERSTANDING YOUR INSTRUMENT PANEL If the parking brake is off and the light remains on, have the brake system inspected as soon as possible. 3. Anti-Lock Warning Light (ABS) — If Equipped This light monitors the Anti-Lock Brake System (ABS) described elsewhere in this manual. This light will come on when the ignition key is turned to the ON position and may stay on for as long as four seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 8. Oil Pressure Light Shows low engine oil pressure. The light will come on and remain on when the ignition key is turned from the OFF to the ON position, and the light will turn off after the engine is started. If the bulb does not come on during starting, have the system checked by an authorized dealer. If the light comes on and remains on while driving, stop the vehicle and shut off the engine. DO NOT OPERATE THE VEHICLE UNTIL THE CAUSE IS CORRECTED.
UNDERSTANDING YOUR INSTRUMENT PANEL 14. Fuel Gauge When the ignition key is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 15. Low Fuel Light — If Equipped NOTE: The Low Fuel Light and Chime feature only functions on vehicles equipped with a tachometer. When the fuel level drops to about 1/8 tank, the fuel symbol will light and a single chime will sound. The light will remain on until fuel is added.
UNDERSTANDING YOUR INSTRUMENT PANEL correct mileage that the vehicle has been driven. Therefore, if the odometer reading changes during repair or replacement, be sure to keep a record of the reading before and after the service so the correct mileage can be determined. blue and red areas of the gauge shows that the engine cooling system is operating properly.
UNDERSTANDING YOUR INSTRUMENT PANEL 83 ELECTRONIC DIGITAL CLOCK RADIO GENERAL INFORMATION The clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the ON or ACC position. Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal.
UNDERSTANDING YOUR INSTRUMENT PANEL Power Button The volume control/power button pops out when pressed, this turns the sound system ON in the mode last used. Pushing the button back in turns the sound system OFF. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it.
UNDERSTANDING YOUR INSTRUMENT PANEL stations to be locked into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice. Every time a preset button is used a corresponding button number will be displayed. Balance The balance control adjusts the left-to-right speaker balance. Press the BAL button in and it will pop out. Adjust the balance and push the button back in. Fade The fade control provides for balance between the front and rear speakers.
UNDERSTANDING YOUR INSTRUMENT PANEL Music Search Pressing the SEEK button while playing a tape will start the Music Search mode. Press the SEEK button up for the next selection on the tape and down to return to the beginning of the current selection, or return to the beginning of the previous selection if the tape is within the first 5 seconds of the current selection. The SEEK symbol appears on the display when Music Search is in operation.
UNDERSTANDING YOUR INSTRUMENT PANEL Mode Button To activate the CD changer, press the MODE button until CD information appears on the display. Push-Button While the CD changer is playing, press the NUMBER 1 push-button or the NUMBER 5 push-button to select a disc numbered higher or lower than the one currently being played. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display.
UNDERSTANDING YOUR INSTRUMENT PANEL Radio Display Messages Your radio has been designed to display certain messages when a problem is detected with the CD player. 89 SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS 4 Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch.
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will bypass stations without stopping until you release it. Bass and Treble Tone Control The tone controls consist of 2 separate bands.
UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice.
UNDERSTANDING YOUR INSTRUMENT PANEL display will show the track number and index time in minutes and seconds. Play will begin at the start of track one. Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection.
UNDERSTANDING YOUR INSTRUMENT PANEL CD Changer Control Capability — If Equipped This radio is compatible with a remote mounted CD changer available through Mopar Accessories. The following instructions are for the radio controls that operate this CD changer. Mode Button To activate the CD changer, press the MODE button until CD information appears on the display.
UNDERSTANDING YOUR INSTRUMENT PANEL An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following reasons: • Excessive vibration • Disc inserted upside down • Damaged disc • Water condensation on optics Radio Display Messages Your radio has been designed to display certain messages when a problem is detected with the CD player.
UNDERSTANDING YOUR INSTRUMENT PANEL SATELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius™ Satellite Radio. This service offers up to 100 channels of music, sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios.
UNDERSTANDING YOUR INSTRUMENT PANEL ESN/SID Access With RBP, RBU, RAZ, and RBQ Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and TIME buttons simultaneously for 3 seconds. All twelve ESN/SID numbers will be displayed. The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed.
UNDERSTANDING YOUR INSTRUMENT PANEL 97 888-539-7474 to discuss options for channel blocking or unblocking. Please have your ESN/SID information available. one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory.
UNDERSTANDING YOUR INSTRUMENT PANEL • Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage. CASSETTE TAPE AND PLAYER MAINTENANCE To keep the cassette tapes and player in good condition, take the following precautions: 1. Do not use cassette tapes longer than C-90; otherwise, sound quality and tape durability will be greatly diminished. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 6 DISC CD CHANGER — IF EQUIPPED The CD changer is located below the radio in the instrument panel. The changer plays only 4 3⁄4 inch (12 cm) discs. The changer holds up to 6 discs. Each disc is loaded and ejected through a single slot in front of the changer. Each disc has a numbered button with an amber light above it which, when illuminated, indicates that a disc is loaded in that particular chamber.
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Button Press the top of this button on the radio once to play the next track. Press the bottom of the button once to return to the beginning of the current track. Press the bottom of the button twice to play the previous track. FF/TUNE/RW Press the FF (fast forward) button and the CD player will fast forward through the tracks until the button is released.
UNDERSTANDING YOUR INSTRUMENT PANEL • Pressing the AM/FM button while in the tape or CD mode will select the radio mode. • If in the CD mode and the last CD is ejected, the radio will tune to the last station selected. Removing Discs from the CD Changer If there is a single CD in the changer, press the EJT button and the CD will eject. If the CD is not removed within 15 seconds, it will automatically reload into the CD changer.
UNDERSTANDING YOUR INSTRUMENT PANEL RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Air is directed through the panel and floor outlets. NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. Defrost Air is directed through the windshield and side window demister outlets. Use this setting with maximum fan and heat settings for the best windshield and side window clearing.
UNDERSTANDING YOUR INSTRUMENT PANEL Outside Air Intake When operating the system during the winter months, make sure the air intake, directly in front of the windshield, is free of ice, slush, snow or other obstructions such as leaves. Leaves collected in the air-intake plenum may reduce air flow and plug the plenum water drains. The blower air will heat faster in cold weather if you use only a low blower speed for the first few minutes of vehicle operation.
UNDERSTANDING YOUR INSTRUMENT PANEL fan speed increases as you move the control counterclockwise from the OFF position. NOTE: The air conditioning compressor will not engage until the engine has been running for about 10 seconds. Fan speeds to the right of OFF are for heater or ventilation operation. The fan speed increases as you move the control clockwise from the OFF position. Mode Control (Air Direction) The mode control allows you to choose from several patterns of air distribution.
UNDERSTANDING YOUR INSTRUMENT PANEL Mix Air is directed through the floor, defrost and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat at the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. Defrost Air is directed through the windshield and side window demist outlets. Use this mode with maximum fan and temperature settings for best windshield and side window defrosting.
UNDERSTANDING YOUR INSTRUMENT PANEL Circulation Control Use this control to choose between outside air intake or recirculation of the air inside the vehicle. Only use the recirculate mode to temporarily block out any outside odors, smoke, or dust and to cool the interior rapidly upon initial start up in very hot or humid weather. This control only operates in the Outside Air and Recirculate modes; there is no in between position. Do not place the control between these positions.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips
UNDERSTANDING YOUR INSTRUMENT PANEL 109 Window Fogging Vehicle side windows tend to fog on the inside in mild rainy or humid weather. To clear the windows, use the A/C, PANEL and blower controls. Direct the panel outlets toward the side windows. Do not use recirculate without A/C for long periods as fogging may occur.
UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRIC REAR WINDOW DEFROSTER A push-button at the center of the instrument panel, below the radio, turns the defroster and the heated mirrors (if equipped) ON or OFF. An amber light shows that the defroster is on. NOTE: The defroster turns off automatically after 10 minutes of operation. Each following activation of the defroster will last for five minutes.
STARTING AND OPERATING CONTENTS m Starting Procedures . . . . . . . . . . . . . . . . . . . . 114 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . . 114 ▫ Manual Transaxle . . . . . . . . . . . . . . . . . . . . . 114 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 114 ▫ Starting In Cold Weather (Below 32°F Of 0°C) . . . . . . . . . . . . . . . . . . . 115 ▫ Extremely Cold Weather (Below -20°F Or -29°C) . . . . . . . . . . . . . . . . .
STARTING AND OPERATING ▫ Anti-Lock Brake System (ABS) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 m Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 125 m Tire Safety Information . . . . . . . . . . . . . . . . . . 125 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 125 ▫ Tire Identification Number (TIN) . . . . . . . . . . 128 ▫ Tire Loading And Tire Pressure . . . . . . . . . . . 129 m Tires—General Information . . . . . . . . . . . . . . .
STARTING AND OPERATING m Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . . 147 113 ▫ Warranty Requirements . . . . . . . . . . . . . . . . . 148 m Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Automatic Transaxle The gear selector must be in the NEUTRAL or PARK position before you can start the engine. CAUTION! NOTE: You must press the brake pedal before shifting out of Park. Long periods of engine idling, especially at high engine speeds can cause excessive exhaust temperatures which can damage your vehicle.
STARTING AND OPERATING Starting in Cold Weather (Below 32°F of 0°C) Slightly depress and hold the accelerator before starting the engine. Turn the key to the START position. When the engine starts, release the key, then the accelerator pedal. If the engine fails to start within 15 seconds, turn the key OFF wait 10 to 15 seconds, then repeat the normal starting procedure. WARNING! Do not attempt to push or tow your vehicle to get it started.
STARTING AND OPERATING CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. After Starting The idle speed will automatically decrease as the engine warms up. AUTOMATIC TRANSAXLE — IF EQUIPPED CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop.
STARTING AND OPERATING NOTE: If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service. Four Speed Automatic Transaxle The electronically controlled transaxle provides a precise shift schedule. The transaxle electronics are self calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt.
STARTING AND OPERATING WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the vehicle into P (Park), remove the key from the ignition, and apply the parking brake. Once the key is removed from the ignition, the transmission shift lever is locked in the P (Park) position, securing the vehicle against unwanted movement.
STARTING AND OPERATING When frequent transaxle shifting occurs while using the Overdrive range, such as when operating the vehicle under heavy loading conditions (in hilly terrain, traveling into strong head winds, or while towing trailers), use the “3” range. 119 MANUAL TRANSAXLE — IF EQUIPPED NOTE: The parking brake should be engaged and the gear selector placed in REVERSE before leaving the vehicle, especially on an incline. NOTE: Clutch must be depressed for engine to start.
STARTING AND OPERATING Never shift into REVERSE until the vehicle has come to a complete stop. NOTE: During cold weather, until the transaxle lubricant has warmed, you may have difficulty shifting. This is normal and not harmful to the transaxle. Recommended Shift Speeds To use your manual transaxle for optimal fuel economy, it should be upshifted as listed in tables 1 and 2.
STARTING AND OPERATING If you exceed these speeds, you may notice the engine cut in and out. This is caused by an electronic limiter in the engine computer. The engine will run normally when you reduce engine speed. Downshifting Proper downshifting may improve fuel economy and prolong engine life. CAUTION! If you skip more than one gear while downshifting or downshift at too high an engine speed, you could damage the engine, transaxle, or clutch.
STARTING AND OPERATING Before leaving the vehicle, make sure that the parking brake is set. To set the parking brake, pull up firmly on the lever. Also place the gear selector in the Park position (automatic transaxle) or Reverse (manual transaxle). To release the parking brake, apply the brake pedal and pull up on the parking brake lever. Push the release button and lower the lever fully.
STARTING AND OPERATING WARNING! • Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake or the gear selector. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle. • Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and an accident.
STARTING AND OPERATING malfunction is caused by an internal leak, as the brake fluid in the master cylinder drops, the brake warning indicator will light. Anti-Lock Brake System (ABS) — If Equipped The ABS gives increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock up.
STARTING AND OPERATING POWER STEERING The power assisted steering system of your vehicle provides mechanical steering capability in the event power assist is lost. If for some reason the hydraulic pressure is interrupted, it will still be possible to steer your vehicle. Under these conditions you will observe a substantial increase in steering effort. TIRE SAFETY INFORMATION Tire Markings 125 NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards.
STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards (....blank....( = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING 127 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (ie. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure 129 Tire and Loading Information Placard Tire Placard Location NOTE: Some vehicles have a “Tire and Loading Information” placard located on the driver’s side “B” pillar. 5 This placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires.
STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
STARTING AND OPERATING 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE: The following table shows examples on how to calculate total load, cargo/luggage and towing capacities of your vehicle with varying seating configurations and 131 number and size of occupants.
STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 133 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3. Ride Comfort and Vehicle Stability— Proper tire inflation contributes to a comfortable ride. Overinflation produces a jarring and uncomfortable ride.
STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1mile (1 km) after a 3 hour period.
STARTING AND OPERATING WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident.
STARTING AND OPERATING CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result. 137 Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 35 mph (55 km/h).
STARTING AND OPERATING Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manufacturer strongly recommends that you use tires equivalent to the originals in size, quality and performance when replacement is needed (see the paragraph on tread wear indicators). Refer to the Tire and Loading Information placard for the size designation of your tire.
STARTING AND OPERATING CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. Alignment And Balance Poor suspension alignment may result in: • Fast tire wear. • Uneven tire wear, such as feathering and one-sided wear. • Vehicle pull to right or left. 139 Tires may also cause the vehicle to pull to the left or right. Alignment will not correct this condition. See your dealer for proper diagnosis.
STARTING AND OPERATING CAUTION! To avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious damage. Stop the vehicle immediately if noise occurs that could indicate chain breakage. Remove the damaged parts of the chain before further use.
STARTING AND OPERATING 141 Tire Rotation Recommendations Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all season type tires.
STARTING AND OPERATING 2.0L High Output Engine Your engine is designed to meet all emission regulations and provide excellent fuel economy and performance when using high quality unleaded gasoline having an octane rating of 91. The purchase of higher octane is not recommended.
STARTING AND OPERATING 143 CAUTION! performance in some vehicles. The manufacturer recommends that gasolines free of MMT be used in your vehicle. The MMT content of gasoline may not be indicated on the gasoline pump, therefore you should ask your gasoline retailer whether or not his/her gasoline contains MMT. DO NOT use gasolines containing Methanol. Gasoline containing methanol may damage critical fuel system components.
STARTING AND OPERATING Malfunction Indicator light to illuminate. The manufacturer recommends that you try a different brand of unleaded gasoline having lower sulfur to determine if the problem is fuel related prior to returning your vehicle to an authorized dealer for service. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: CAUTION! If the Check Engine or Service Engine Soon light is flashing, immediate service is required.
STARTING AND OPERATING resulting from the use of such fuels or additives is not the responsibility of the manufacturer and may not be covered under the New Vehicle Warranty. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases.
STARTING AND OPERATING CAUTION! CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. CAUTION! A poorly fitting gas cap may cause the Malfunction Indicator Lamp to turn on. NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
STARTING AND OPERATING 147 WARNING! WARNING! • Remove the fuel tank filler tube cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury. • The volatility of some gasolines may cause a build up of pressure in the fuel tank that may increase while you drive. This pressure can result in a spray of gasoline and/or vapors when you remove the cap from a hot vehicle. Removing the cap slowly allows the pressure to vent and prevents fuel spray.
STARTING AND OPERATING TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer carefully review this information to tow your load as efficiently and safely as possible. To maintain warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing. Perform maintenance services as prescribed in the maintenance schedules manual.
STARTING AND OPERATING and Loading Information placard. Refer to the Tire– Safety Information Section in this manual. • The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range must be selected. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance and extend transaxle life by reducing excessive shifting and heat build up.
WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Flasher . . . . . . . . . . . . . . . . . 152 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 m If Your Engine Overheats . . . . . . . . . . . . . . . . 152 m Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 160 m Jacking And Tire Changing . . . . . . . . . . . . . . . 153 m Towing A Disabled Vehicle . . . . . . . . . . . . . . . 161 ▫ Preparations For Jacking . . . . . . . . . . . . . . . . 154 ▫ With Ignition Key .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and the vehicle locked. NOTE: With extended use, the flasher may wear down your battery. IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. • On the highways — Slow down.
WHAT TO DO IN EMERGENCIES CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, turn the engine off immediately, and call for service. WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant.
WHAT TO DO IN EMERGENCIES Preparations For Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, and set the parking brake. Place the gear selector in PARK (automatic transaxle) or REVERSE (manual transaxle). • Turn on the Hazard Warning Flasher. • Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if changing the right front tire, block the left rear wheel.
WHAT TO DO IN EMERGENCIES CAUTION! 155 Do not raise the vehicle until you are sure the jack is securely engaged. Do not attempt to raise the vehicle by jacking on the crossmember below the radiator or on the front suspension crossmember. 3. Jack saddle support must be positioned in between locating darts at the front of the vehicle and behind locating dart at the rear. Turn the jack screw to the right until the jack head is properly engaged with the lift area closest to the wheel to be changed. 6 4.
WHAT TO DO IN EMERGENCIES WARNING! align the wheel cover to the valve stem, place the wheel cover onto the wheel, then install the wheel nuts. Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Lower the vehicle by turning the jack screw to the left. 5. Remove the wheel nuts and pull the wheel and wheel covers where applicable off the hub.
WHAT TO DO IN EMERGENCIES NOTE: The spare tire well is designed to hold the compact spare tire or a deflated (flat) tire. A fully inflated tire will not fit in the spare tire well. JUMP-STARTING PROCEDURES IF BATTERY IS LOW WARNING! Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be hurt by the fan. 157 WARNING! Do not attempt to push or tow your vehicle to get it started.
WHAT TO DO IN EMERGENCIES 4. Connect one end of a jumper cable to the positive terminal of the booster battery. Connect the other end to the positive terminal of the discharged battery. WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result. WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing.
WHAT TO DO IN EMERGENCIES 159 WARNING! WARNING! Do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump starting because the battery could rupture or explode. The battery temperature must be brought up above freezing point before attempting to jump start.
WHAT TO DO IN EMERGENCIES WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have an accident. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet, mud, loose sand, etc.). Traction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface.
WHAT TO DO IN EMERGENCIES WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed.
WHAT TO DO IN EMERGENCIES All Transaxles CAUTION! If the vehicle being towed requires steering, the ignition switch must be in the OFF position, not in the LOCK or ACCESSORY positions. If it is necessary to use the accessories while being towed (wipers, defrosters, etc.), the key must be in the ON position, not the ACCESSORY position. Make certain the transaxle remains in NEUTRAL. Without The Ignition Key Special care must be taken when the vehicle is towed with the ignition in the LOCK position.
MAINTAINING YOUR VEHICLE CONTENTS m 2.0L Engine Compartment . . . . . . . . . . . . . . . 165 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . . . 175 m Onboard Diagnostic System — OBD II . . . . . . 166 ▫ Air Conditioner . . . . . . . . . . . . . . . . . . . . . . 176 m Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 ▫ Power Steering Fluid Check . . . . . . . . . . . . . . 177 m Replacement Parts . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Hoses And Vacuum/Vapor Harnesses . . . . . . . 184 m Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 197 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . . 185 ▫ Headlight Bulb Replacement . . . . . . . . . . . . . 197 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . . 187 ▫ Front Park/Turn Signal Lights . . . . . . . . . . . . 199 ▫ Manual Transaxle . . . . . . . . . . . . . . . . . . . . . 189 ▫ Front Sidemarker Light . . . . . . .
MAINTAINING YOUR VEHICLE 165 2.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing.
MAINTAINING YOUR VEHICLE If your OBD system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update. A recheck with the above test routine may then indicate that the system is now ready.
MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. 169 Engine Oil Checking Oil Level To assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop.
MAINTAINING YOUR VEHICLE the oil level between the MIN and MAX markings on the dipstick. Adding one quart of oil when the reading is at the MIN mark will result in a MAX reading on these engines. Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to decide if any apply to you. • Day and night temperatures are below 32°F (0°C) CAUTION! Overfilling or underfilling will cause aeration or loss of oil pressure.
MAINTAINING YOUR VEHICLE NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the 9Maintenance Schedules9 section of this manual. If none of these apply to you, then change your engine oil at every interval shown on schedule 9A9 of the 9Maintenance Schedules9 section of this manual. NOTE: Under no circumstances should oil change intervals exceed 6000 miles (10 000 km) or 6 months whichever comes first.
MAINTAINING YOUR VEHICLE the engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental additives. Disposing of Used Engine Oil Care should be taken in disposing of used engine oil from your vehicle. Used oil, indiscriminately discarded, can present a problem to the environment. Contact your dealer, service station, or governmental agency for advice on how and where used oil can be safely discarded in your area.
MAINTAINING YOUR VEHICLE 173 Drive Belts — Check Condition and Tension At the mileage shown in the maintenance schedules, check all drive belts for condition and proper tension. Improper belt tension can cause belt slippage and failure. Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device.
MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE 175 Fuel Filter A plugged fuel filter can cause hard starting or limit the speed at which a vehicle can be driven. Should an excessive amount of dirt accumulate in the fuel tank, frequent filter replacement may be necessary. Maintenance-Free Battery The top of the MAINTENANCE-FREE battery is permanently sealed. You will never have to add water, nor is periodic maintenance required.
MAINTAINING YOUR VEHICLE WARNING! CAUTION! Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling. Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Battery gas is flammable and explosive.
MAINTAINING YOUR VEHICLE a gentle water spray from behind the radiator and through the condenser as required. Fabric front fascia protectors may reduce air flow to the condenser, reducing air conditioning performance. WARNING! The air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced repairman.
MAINTAINING YOUR VEHICLE If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid types. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of a high quality lubricant such as Mopart Lock Cylinder Lubricant directly into the lock cylinder.
MAINTAINING YOUR VEHICLE Windshield Wiper Blade Replacement 1. Lift the wiper arm away from the glass. 2. Rotate the blade 45 degrees to gain access to the release tab. 3. Push the release tab shown in the picture and slide the wiper blade assembly down along the arm. Gently place the wiper arm on the windshield. 179 Windshield Washer Aiming To change the aim of the windshield washers, place a safety pin into the nozzle opening and move the nozzle slightly.
MAINTAINING YOUR VEHICLE into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required. WARNING! Exhaust gases can injure or kill. They contain carbon monoxide which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. Follow the above precautions to keep your exhaust system as safe as possible.
MAINTAINING YOUR VEHICLE Check the front of the radiator for an accumulation of bugs, leaves, etc. Clean the radiator by gently spraying water from a garden hose at the back of the core. Check the recovery bottle tank tubing for condition and tightness of connection at the bottle and radiator. Inspect the entire system for leaks.
MAINTAINING YOUR VEHICLE CAUTION! Mixing of coolants other than specified (nonHOAT), may result in engine damage that may not be covered under the new vehicle warranty, and decreased corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible. Do not use plain water alone or alcohol base antifreeze products.
MAINTAINING YOUR VEHICLE The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. WARNING! 183 coolant freeze point or replacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. never add coolant when the engine is overheated.
MAINTAINING YOUR VEHICLE of the engine compartment. This is normally a result of moisture from rain, snow, or high humidity accumulation on the radiator and being vaporized when the thermostat opens, allowing hot water to enter the radiator. If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. A. Do not overfill the coolant bottle. B. Check coolant freeze point in the system. C.
MAINTAINING YOUR VEHICLE Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present. Components should be replaced immediately if there is any evidence of degradation that could cause failure. Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Suggested service intervals can be found in the Maintenance Section.
MAINTAINING YOUR VEHICLE NOTE: Inspection of brake hoses should be done whenever the brake system is serviced and every engine oil change. WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning lamp is on.
MAINTAINING YOUR VEHICLE 187 WARNING! CAUTION! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Using a transmission fluid other than the manufacturers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes.
MAINTAINING YOUR VEHICLE To check the fluid level properly, the following procedure must be used: 1. The vehicle must be on level ground. reference holes when the transmission reaches 180°F (82°C). Remember it is best to check the level at the normal operating temperature. 2. The engine should be running at curb idle speed for at minimum of 60 seconds. 3. Fully apply parking brake. 4. Place the gear selector momentarily in each gear position ending with the lever in P (PARK). 5.
MAINTAINING YOUR VEHICLE 189 CAUTION! If the transaxle is disassembled for any reason, the fluid and filter should be changed. Do not overfill. Dirt and water in the transaxle can cause serious damage. To prevent dirt and water from entering the transaxle after checking or replenishing fluid, make certain that the dipstick cap is seated properly. Special Additives The manufacturer recommends against the addition of any fluid additives to the transaxle.
MAINTAINING YOUR VEHICLE Frequency of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless the following conditions exist: • The lubricant has become contaminated with water. If contaminated with water, the fluid should be changed immediately. • If severe usage has occurred, refer to Maintenance Schedule “B” in Section 8 of this manual.
MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar or other similar deposits have accumulated on your vehicle, wash it as soon as possible. • Use Mopar auto polish to remove road film and stains and to polish your vehicle. Take care never to scratch the paint.
MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. • If you carry special cargo such as chemicals, fertilizers, deicer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.
MAINTAINING YOUR VEHICLE Interior Care Use Mopar Fabric Cleaner to clean fabric upholstery and carpeting. Use Mopar Vinyl Cleaner to clean vinyl upholstery. Mopar Vinyl Cleaner is specifically recommended for vinyl trim. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth.
MAINTAINING YOUR VEHICLE Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters. Do not use scrapers or other sharp instruments which may scratch the elements. Instrument Panel Cover The instrument panel cover has a low glare surface which minimizes reflections in the windshield.
MAINTAINING YOUR VEHICLE FUSES Underhood Fuses (Power Distribution Center) A Power Distribution Center is located in the engine compartment; next to the battery. A label identifying the components and circuits is located on the underside of the cover. 195 Interior Fuses The fuse access panel is behind the end cover at the left side of the instrument panel. To remove the panel, pull it out, as shown. A diagram identifying the components and circuits is located on the inside of the cover.
MAINTAINING YOUR VEHICLE CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it shows a problem in the circuit that must be corrected. VEHICLE STORAGE If you will not be using your vehicle for more than 21 days you may want to take steps to preserve your battery.
MAINTAINING YOUR VEHICLE LIGHTS BULBS — Outside Bulb No. Headlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9007 Front Park/Turn Signal Light . . . . . . . . . . . . . 3457AK Front Side Marker Light. . . . . . . . . . . . . . . . . . . . 168 Front Fog Light . . . . . . . . . . . . . . . . . . . . . . . . . . 899 Center High Mounted Stop Light (CHMSL) . . . . . . . . . . . . . . . . . . . . . . . . . 921–W16W Rear Tail/Stop/Turn Signal Light . . . . . . 3157–P27/7W Backup Light . . . . . .
MAINTAINING YOUR VEHICLE 2. Remove two screws from the headlight assembly and remove the assembly from the vehicle. NOTE: The headlight assembly is located to the fender by a molded pin. Pull the outboard side of the headlight straight out until the molded pin clears the fender, then slide the headlight out from behind the bumper fascia and grille. 3. Disconnect the electrical connector. 4. Remove the retaining ring and replace the bulb.
MAINTAINING YOUR VEHICLE 199 Front Park/Turn Signal Lights Tail/Stop, Rear Turn Signals and Back-up Lights 1. Remove the headlight assembly 1. Open the trunk and move the trunk liner away from the rear light mounting area. 2. Twist the bulb socket 1/4 turn and remove. 3. Pull the bulb from the socket and replace. Front Sidemarker Light 1. Remove the screws and push-pins from the front fender splash shield. 2.
MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel (Approximate) Standard 2.0L Engines 87 Octane High Output 2.0L Engines 91 Octane Engine Oil-With Filter 2.0 Liter Engines (SAE 5W-30, API Certified Engine Oils) Cooling System * 2.0 Liter Engines (Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula) * Includes heater and coolant recovery bottle filled to MAX level. U.S. Metric 12.5 Gallons 12.5 Gallons 47.5 Liters 47.5 Liters 4.5 qts 4.3 Liters 6.5 qts 6.
MAINTAINING YOUR VEHICLE 201 RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluids, Lubricants and Genuine Parts Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) Use API Certified SAE 5W-30 Engine Oil. Refer to oil viscosity chart for correct SAE grade meeting DaimlerChrysler Material Standard MS-6395. Mopar 4105409 or equiv.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E m Emission Control System Maintenance . . . . . . 204 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 207 m Maintenance Schedules . . . . . . . . . . . . . . . . . . 204 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 204 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES • If equipped for and operating with E-85 (ethanol) fuel. 205 M At Each Stop for Fuel A I N T E N A N C E NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the 9Maintenance Schedules9 section of this manual. • Check the engine oil level about 5 minutes after a fully warmed engine is shut off.
M A I N T E N A N C E S C H E D U L E S 8 206 MAINTENANCE SCHEDULES • Check rubber seals on each side of the radiator for proper fit. • Check the automatic transaxle fluid level. At Each Oil Change • Check the manual transaxle fluid level and fill plug condition. • Change the engine oil filter. • Check the coolant level, hoses, and clamps. • Inspect the exhaust system.
SCHEDULE “B” Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an L. Change the manual transaxle fluid every 48,000 miles (77 000 km) if the vehicle is usually operated under one or more of the conditions marked with an †. • Day or night temperatures are below 32°F (0°C).
M 208 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Inspect the front brake pads and rear brake linings N C and rotors. E Inspect and replace, if required, the make-up air S C H E D U L E S 8 filter (located inside the air cleaner). Inspect and replace, if required, the air cleaner element (filter).
SCHEDULE “B” Miles (Kilometers ) Change engine oil and engine oil filter. Inspect the front brake pads and rear brake linings and rotors. Replace air cleaner element (filter). Check and replace, if necessary, the PCV valve. * Adjust the generator belt tension. Replace the make-up air filter (located inside the air cleaner). Replace the spark plugs. Inspect the tie rod ends and boot seal.
M 210 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Inspect the front brake pads and rear brake linings N C and rotors. E Inspect and replace, if necessary, the air cleaner S C H E D U L E S 8 element (filter). * Inspect and replace, if required, the make-up air filter (located inside the air cleaner).
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect the front brake pads and rear brake linings and rotors. Replace air cleaner element (filter). Check and replace, if necessary, the PCV valve. *‡ Change the automatic transaxle fluid and adjust the bands.L Replace manual transaxle fluid.† Inspect the tie rod ends and boot seals. Replace the drive belts. Replace the make-up air filter (located inside the air cleaner). Replace the spark plugs. Replace the ignition cables.
M 212 SCHEDULE “B” A I N Miles T ( Kilometers) E N Change engine oil and engine oil filter. A Inspect the front brake pads and rear brake linings N C and rotors. E Inspect and replace, if necessary, the air cleaner S C H E D U L E S 8 element (filter). * Inspect and replace, if required, the make-up air filter (located inside the air cleaner).
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect the front brake pads and rear brake linings and rotors. Replace air cleaner element (filter). Check and replace, if necessary, the PCV valve. *‡ Inspect the tie rod ends and boot seals. Adjust the generator drive belt tension. Replace the make-up air filter (located inside the air cleaner). Replace the spark plugs.
M 214 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Inspect the front brake pads and rear brake linings N C and rotors. E Inspect and replace, if necessary, the air cleaner S C H E D U L E S 8 93,000 (149 000) X element (filter). * Replace manual transaxle fluid.† Flush and replace the engine coolant. Replace the engine timing belt. Inspect and replace, if required, the make-up air filter (located inside the air cleaner).
SCHEDULE “A” 215 M Schedule “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the make-up air filter (located inside the air cleaner).
M 216 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Inspect the brake linings. E Replace the engine air cleaner filter. S C H E D U L E S 8 Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace, if necessary.* Flush and replace the engine coolant at 60 months, regardless of mileage. Replace the make-up air filter (located inside the air cleaner). Replace drive belts.
SCHEDULE “A” Miles (Kilometers) 72,000 (115 000) [Months] Change engine oil and engine oil filter. Inspect the front brake pads and rear brake linings and rotors. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Replace the make-up air filter (located inside the air cleaner). Adjust the generator drive belt tension.
M 218 SCHEDULE “A” A I WARNING! N T E You can be badly injured working on or around a N motor vehicle. Do only that service work for which A you have the knowledge and the right equipment. If N C you have any doubt about your ability to perform a E S C H E D U L E S 8 service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 ▫ Prepare For The Appointment . . . . . . . . . . . . 220 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 220 m Reporting Safety Defects . . . . . . . . . . . . . . . . . 224 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 224 m Publication Order Forms . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center.
IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unexpected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands behind only the manufacturer’s Service Contracts. If you purchased a manufacturer’s Service Contract, you will receive Plan Provisions and an Owner Identification Card in the mail within three weeks of your vehicle delivery date.
IF YOU NEED CONSUMER ASSISTANCE 223 9
IF YOU NEED CONSUMER ASSISTANCE MOPART PARTS Mopart fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
IF YOU NEED CONSUMER ASSISTANCE technicians to find and fix problems on computercontrolled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-by-step troubleshooting and driveability procedures, proven diagnostic tests and a complete list of all tools and equipment. PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below.
IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car.
IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
INDEX ABS (Anti-Lock Brake) System . . . . . . . . . . . . . 124 Adding Engine Coolant (Antifreeze) . . . . . . . . . 182 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Air Cleaner, Engine . . . . . . . . . . . . . . . . . . . . . 175 Air Conditioning . . . . . . . . . . . . . . . . . . . . 104,176 Air Conditioning Controls . . . . . . . . . . . . . . . . 104 Air Conditioning Refrigerant . . . . . . . . . . . . . . 177 Air Conditioning System . . . . . . . . . . . . . . . . .
INDEX Brake System . . . . . . . . . . . . . . . . . . . . . . . 123,185 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . 186 Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 Warning Light . . . . . . . . . . . . . . . . . . . . . . . . 78 Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123,185 Brake/Transmission Interlock . .
INDEX Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Contract, Service . . . . . . . . . . . . . . . . . . . . . . . 222 Coolant . . . . . . . . . . . . . . . . . . . . . . . . 181,200,201 Cooling System . . . . . . . . . . . . . . . . . . . . . . . . 180 Adding Coolant (Antifreeze) . . . . . . . . . . . . . 182 Coolant Level . . . . . . . . . . . . . . . . . . . . . 180,183 Disposal of Used Coolant . . . . . . . . . . . . . . . 181 Drain, Flush, and Refill . . . . . . . . .
INDEX Emission Control System Maintenance . . . . 167,204 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 Break-In Recommendations . . . . . . . . . . . . . . . 46 Checking Oil Level . . . . . . . . . . . . . . . . . . . . 169 Compartment . . . . . . . . . . . . . . . . . . . . . . . . 165 Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 Exhaust Gas Caution . . . . . . . . . . . . . . . . . . 145 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Octane Rating . . . . . . . . . . . . . . . . . . . . . . . . 141 Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . 200 Fuel System Caution . . . . . . . . . . . . . . . . . . . . 144 Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 Gas Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Gasoline . . . . .
INDEX Jack Operation . . . . . . . . . . . . . . . . . . . . . . . . . 153 Jacking Instructions . . . . . . . . . . . . . . . . . . . . . 154 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 157 Key, Programming . . . . . . . . . . . . . . . . . . . . . . . 12 Key Release Button . . . . . . . . . . . . . . . . . . . . . . . 9 Key, Replacement . . . . . . . . . . . . . . . . . . . . . . . 12 Key, Sentry . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Key-In Reminder . . . . . . . .
INDEX Theft Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Turn Signal . . . . . . . . . . . . . . . . . . . . . 62,79,199 Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Warning (Instrument Cluster Description) . . . . 78 Loading Vehicle . . . . . . . . . . . . . . . . . . . . . . . . 147 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Child Protection . . . . . . . .
INDEX Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Identification Logo . . . . . . . . . . . . . . . . . . . . 171 Materials Added to . . . . . . . . . . . . . . . . . . . . 172 Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 Recommendation . . . . . . . . . . . . . . . . . . 171,200 Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Viscosity . . . . . . . . . . . . . . . .
INDEX Release, Hood . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Remote Keyless Entry . . . . . . . . . . . . . . . . . . . . 17 Remote Trunk Release . . . . . . . . . . . . . . . . . . . . 21 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . . . 196 Replacement Keys . . . . . . . . . . . . . . . . . . . . . . . 12 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . 168 Replacement Tires . . . . . . . . . . . . . . . . . . . . . . 138 Reporting Safety Defects . . . . . . .
INDEX Speed Control . . . . . . . . . . . . . . . . . . . . . . . . 65,82 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Speedometer and Odometer . . . . . . . . . . . 75,76,77 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Engine Fails to Start . . . . . . . . . . . . . . . . . . . 115 Starting Procedures . . . . . . . . . . . . . . . . . . . . . 114 Steering Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 Tilt Column . . . . . . . . . .
INDEX Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 140 Spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Tread Wear Indicators . . . . . . . . . . . . . . . . . . 137 Towing Disabled Vehicle . . . . . . . . . . . . . . . . . . . . . . 161 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . 148 Minimum Requirements . . . . . . . . . . . . . . . . 148 Trailer and Tongue Weight . . . . . . . . . . . . . . 149 Warnings . . . . . . . . . . . . . . . . . . .
INDEX 241 Windows Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Windshield Washer Aiming . . . . . . . . . . . . . . . 179 Windshield Washers . . . . . . . . . . . . . . . . . . . . . 63 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 Windshield Wiper Blades . . . . . . . . . . . . . . . . . 178 Windshield Wipers . . . . . . . . . . . . . . . . . . . . . . 63 Wiper Blade Replacement . . . . . . . . . . . . . . . . . 179 Wipers, Intermittent . . . . . . . . . .