2010 OWNE R ’ S MANUAL Ram Truck
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Van Conversions/Campers . . . . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number .............. 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 6 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION NOTE: It is illegal to remove or alter the VIN. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through VEHICLE MODIFICATIONS/ALTERATIONS the windshield. This number also appears on the AutoWARNING! mobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 ▫ General Information . . . . . . . . . . . . . . . . . . . 17 ▫ Wireless Ignition Node (WIN) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 12 䡵 Vehicle Security Alarm — If Equipped . . . . . . . . 18 ▫ Key FOB . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 ▫ Removing Key FOB From Ignition . . . . . . . . . 14 ▫ Key-In-Ignition Reminder . . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Remote Open Window Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 23 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 24 ▫ Programming Additional Transmitters . . . . . . 24 ▫ Transmitter Battery Replacement . . . . . . . . . . 24 ▫ General Information . . . . . . . . . . . . . . . . . . . 25 䡵 Remote Starting System — If Equipped . . . . . . . 25 ▫ Power Windows – If Equipped . . . . . . . . . . . . 34 ▫ Wind Buffeting .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Driver And Right Front Passenger 䡵 Engine Break-In Recommendations . . . . . . . Supplemental Restraint System (SRS) – 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 ▫ Transporting Passengers . . . . . . . . . . . . . ▫ Airbag System Components . . . . . . . . . . . . . . 51 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . ▫ Advanced Front Airbag Features . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Key Fob with Remote Keyless Entry (RKE) — If Equipped Your vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the Key Fob into the ignition switch with either side up. authorized dealer. Ask your authorized dealer for these numbers and keep them in a safe place.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead. You can keep the emergency key with you when valet parking.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To remove the emergency key, slide the mechanical latch Removing Key Fob From Ignition at the top of the Key Fob sideways with your thumb and Place the shift lever in PARK. Turn the Key Fob to the OFF position and then remove the Key Fob. then pull the key out with your other hand.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 (EVIC)/Personal Settings (Customer-Programmable Key-In-Ignition Reminder Features)” in “Understanding Your Instrument Panel” Opening the driver’s door when the Key Fob is in the ignition and the ignition switch position is OFF or ACC, for further information. sounds a signal to remind you to remove the Key Fob. WARNING! Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system uses Key Fob with factory-mated Remote Keyless Entry (RKE) transmitter and Wireless Ignition Node (WIN) to prevent unauthorized vehicle operation. Therefore, only Key Fobs that are programmed to the vehicle can be used to start and operate the vehicle. The system will not allow the engine to crank if an invalid Key Fob is used to start and operate the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! Always remove the Sentry Keys威 from the vehicle and lock all doors when leaving the vehicle unattended. At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). Keep the PIN in a secure location. This number is required for authorized dealer replacement of Key Fobs.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE VEHICLE SECURITY ALARM — IF EQUIPPED The Vehicle Security Alarm monitors the vehicle doors and ignition for unauthorized operation. When the Vehicle Security Alarm is activated, the system provides both audible and visible signals. For the first three minutes the horn will sound and the headlights, park lamps and/or turn signals will flash and Vehicle Security Light will flash repeatedly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Vehicle Security Alarm will also disarm if the vehicle is started with a programmed Sentry Key威. If an unprogrammed Sentry Key威 is used to start a vehicle, the engine will run for two seconds and then the alarm will be initiated. To exit the alarming mode, press the RKE transmitter UNLOCK button, or start the vehicle with a programmed Sentry Key威.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED The RKE system allows you to lock or unlock the doors and activate the Panic Alarm from distances up to approximately 66 ft (20 m) using a hand-held radio transmitter with integrated key. The transmitter does not need to be pointed at the vehicle to activate the system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Key Unlock, Driver Door/All Doors First This feature lets you program the system to unlock either the driver’s door or all doors on the first press of the UNLOCK button on the RKE transmitter. To change the current setting, proceed as follows: • For vehicles equipped with the EVIC, refer to “Electronic Vehicle Information Center (EVIC)/CustomerProgrammable Features (System Setup)” in “Understanding Your Instrument Panel” for further information. 21 2.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Flash Lamps with Remote Key Lock This feature will cause the turn signal lights to flash when the doors are locked or unlocked with the RKE transmitter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • For vehicles equipped with the EVIC, refer to “Electronic Vehicle Information Center (EVIC)/CustomerProgrammable Features (System Setup)” in “Understanding Your Instrument Panel” for further information. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sound Horn with Remote Key Lock This feature will cause the horn to chirp when the doors are locked with the RKE transmitter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • For vehicles equipped with the EVIC, refer to “Electronic Vehicle Information Center (EVIC)/CustomerProgrammable Features (System Setup)” in “Understanding Your Instrument Panel” for further information. 23 3.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using the Panic Alarm • You may need to be less than 35 ft (11 m) from the To turn the Panic Alarm feature ON or OFF, press and vehicle when using the RKE transmitter to turn off the hold the PANIC button on the RKE transmitter for at Panic Alarm due to the radio frequency noises emitted least one second and release. When the Panic Alarm is on, by the system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 1. With the RKE transmitter buttons facing down, use a NOTE: Changes or modifications not expressly apflat blade to pry the two halves of the RKE transmitter proved by the party responsible for compliance could apart. Make sure not to damage the seal during removal. void the user’s authority to operate the equipment. 2. Remove and replace the battery. Avoid touching the If your RKE transmitter fails to operate from a normal new battery with your fingers.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Use Remote Start All of the following conditions must be met before the engine will remote start: • Shift lever in PARK • Doors closed • Hood closed • HAZARD switch off • BRAKE switch inactive (brake pedal not pressed) • Ignition key removed from ignition switch • Battery at an acceptable charge level • RKE PANIC button not pressed • Fuel meets minimum requirement WARNING! • Do not start or run an engine in a closed garage or confined area.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Remote Start Aborted - Hood Ajar • Remote Start Aborted - Fuel Low • Remote Start Aborted - System Fault 27 • For security, power window and power sunroof operation (if equipped) are disabled when the vehicle is in the Remote Start mode. • The engine can be started two consecutive times (two The EVIC message stays active until the ignition is turned 15-minute cycles) with the RKE transmitter. However, to the ON/RUN position.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Exit Remote Start Mode and Drive the Vehicle Before the end of the 15-minute cycle, press and release the UNLOCK button on the RKE transmitter to unlock the doors and disarm the Vehicle Security Alarm System (if equipped). Insert the Key Fob into the ignition switch and turn the switch to the ON/RUN position. turn on in cold weather. In warm weather, the driver vented seat feature will automatically turn on when the remote start is activated.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 Front doors may be opened with the inside door handle Power Door Locks — If Equipped A power door LOCK switch is on each front door trim without lifting the lock plunger. panel. Use this switch to lock or unlock the doors. Doors locked before closing will remain locked when closed. The emergency key will unlock the driver door lock on your vehicle.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE power locks will not operate. This prevents you from accidentally locking your Key Fob in the vehicle. Removing the Key Fob or closing the door will allow the locks to operate. A chime will sound if the Key Fob is in the ignition switch and a door is open, as a reminder to remove the Key Fob. • For vehicles not equipped with the EVIC, perform the following procedure: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 8. If a chime is not heard, program mode was canceled • For vehicles not equipped with the EVIC, perform the before the feature could be disabled. If necessary, repeat following procedure: the above procedure. 1. Enter your vehicle and close all doors. Auto Unlock Doors — If Equipped 2. Fasten your seat belt.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 7. Repeat the above steps to alternate the availability of this feature. 8. If a chime is not heard, the program mode was canceled before the feature could be changed. If necessary, repeat the above procedure. Child Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors (if equipped) of your vehicle have the child protection door lock system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position. 33 WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: • After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS Power Windows – If Equipped The control on the left front door panel has UP-DOWN switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of Quad Cab威, Mega Cab威 and Crew Cab models.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 WARNING! To open the window part way, press to the first detent and release it when you want the window to stop. Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE rough road conditions may trigger the auto reverse function unexpectedly during auto closure. If this happens, pull the switch lightly to the first detent and hold to close the window manually. press the window LOCK button into the latched or down position. To enable the window controls, press the window LOCK button again and return the switch to the released or up position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down or in partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Please pay close attention to the information in this section. It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible. WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 WARNING! WARNING! (Continued) • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Wearing a seat belt incorrectly is dangerous.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Latch Plate To Buckle 41 WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WARNING! WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision, it could even cut into you. Be sure the belt is straight.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE belt tongue is pressed into the buckle. Allow the retractor to take up the surplus webbing, and the buckles will hang vertically from the cab back exit bezel, thus freeing up all the area behind the front seats. 2. To reattach the seat belt to the front center seat, pull the black buckle latch plate forward from the cab back panel and insert it into the black keyed buckle until there is an audible “click”.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 2 Inserting Latch Plate In Use Position
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • If the black latch and black buckle are not properly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision. • When reattaching the black latch and black buckle, ensure the seat belt webbing is not twisted.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE you will prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Center Lap Belts The center seating position for the Quad Cab威, Mega Cab威 and Crew Cab front seat has a lap belt only. To fasten the lap belt, slide the latch plate into the buckle until you hear a ⬙click.⬙ To lengthen the lap belt, tilt the latch plate and pull. To remove slack, pull the loose end of the webbing.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Use The Automatic Locking Mode 1. Buckle the combination lap/shoulder belt. by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints. 2. Grasp the shoulder portion and pull downward until NOTE: These devices are not a substitute for proper seat the entire belt is extracted. belt placement by the occupant. The seat belt still must be 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Once the warning is triggered, the BeltAlert威 will continue to chime and flash the Seat Belt Reminder Light for 96 seconds or until the driver’s seat belt is buckled. The BeltAlert威 will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). 49 3.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Pregnant women should wear the lap part of the belt across the thighs and as snug against the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 The Advanced Front Airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on the severity and type of collision. This vehicle may also be equipped with Supplemental Side Airbag Inflatable Curtains (SABIC) to protect the driver, front, and rear passengers sitting next to a window.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Front Passenger Airbag • Front and Side Impact Sensors — if equipped • Steering Wheel and Column • Instrument Panel • Knee Impact Bolster • Front Seat Belt Pretensioners — if equipped • Supplemental Side Airbag Inflatable Curtains (SABIC) — if equipped Advanced Front Airbag Features The Advanced Front Airbag system has multistage driver and front passenger airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not put anything on or around the airbag covers or attempt to open them manually. You may damage the airbags and you could be injured because the airbags may no longer be functional. The protective covers for the airbag cushions are designed to open only when the airbags are inflating. • Do not drill, cut or tamper with the knee bolster in any way.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system includes sensors adjacent to both front and rear seat occupants that are calibrated to deploy the SABIC airbags during impacts that require airbag occupant protection. WARNING! • If your vehicle is equipped with left and right Side Airbag Inflatable Curtain (SABIC), do not stack luggage or other cargo up high enough to block the location of the SABIC. The area where the side curtain airbag is located should remain free from any obstructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Infants in rear-facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag. An airbag deployment can cause severe injury or death to infants in that position. 55 You should read the instructions provided with your child restraint to make sure that you are using it properly. All occupants should ALWAYS wear their lap and shoulder belts properly.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions, the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during front airbag deployment could cause serious injury, including death. Airbags need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Advanced Front Airbags will not deploy in all frontal collisions, including some that may produce substantial vehicle damage — for example, some pole collisions, truck underrides, and angle offset collisions. On the other hand, depending on the type and location of impact, Advanced Front Airbags may deploy in crashes with little vehicle front-end damage but that produce a severe initial deceleration. The side airbags will not deploy in all side collisions.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE It also includes diagnostics that will illuminate the instrument cluster Airbag Warning Light if a malfunction is noted. The diagnostics also record the nature of the malfunction. WARNING! Ignoring the Airbag Warning Light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 deploy the SABIC airbags, depending on severity and Front and Side Impact Sensors — If Equipped type of collision. In these events, the ORC will deploy the In front and side impacts, impact sensors aid the ORC in determining appropriate response to impact events. AdSABIC only on the impact side of the vehicle.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Turn on the interior lights, which remain on as long as the battery has power or until the ignition key is removed. • Unlock the doors automatically. floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and the front passenger seat belt retractor assembly replaced by an authorized dealer as soon as possible. Also, have the Occupant Restraint Controller (ORC) system serviced as well. 61 Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not attempt to modify any part of your advanced airbag system. The airbag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any advanced airbag system service. If your seat, including your trim cover and cushion, needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 located on the inside of the fuse block cover for the 2. Under certain circumstances, EDR data may not be proper airbag fuses. See your authorized dealer if the recorded (e.g., loss of battery power). fuse is good.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE accessing the electronic data stored, unless ordered to download data by a court with legal jurisdiction (i.e., pursuant to a warrant). A copy of the data will be provided to the custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the U.S. government and various states.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 United States and all Canadian provinces require that Infants and Small Children small children ride in proper restraint systems. This is the There are different sizes and types of restraints for children from newborn size to the child almost large law, and you can be prosecuted for ignoring it. enough for an adult safety belt. Use the restraint that is Children 12 years and younger should ride properly correct for your child.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE infant carriers do, so they can be used rearward-facing by children who weigh more than 20 lbs (9 kg) but are less than one year old. cushion while the child’s back is against the seat back, they should use a belt-positioning booster seat. The child and booster seat are held in the vehicle by the lap/shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips for getting the most out of your child restraint: 67 from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out. • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety • If the belt still can’t be tightened, or if pulling and Standards.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Lower Anchors and Tether for CHildren (LATCH) Each vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tether for CHildren.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products. Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchorages will continue to have features for installation in vehicles using the lap or lap/shoulder belt.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing the Child Restraint System WARNING! Do not install child restraint systems equipped with LATCH attachments in the center position of a Quad Cab威, Mega Cab威 or Crew Cab model rear seat. The LATCH anchorages in this seat are designed for the two outboard seating positions only. A child may be placed in the rear center seating position of a Quad Cab威, Mega Cab威 or Crew Cab model using the seat belt and child tether anchorage.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing Child Restraints Using the Vehicle Seat Belt The seat belts in the passenger seating positions are equipped with either an Automatic Locking Retractor (ALR) or a cinching latch plate or both. Both types of seat belts are designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a locking clip.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! 3. Install the child restraint and remove the slack in the tether strap according to the manufacturer’s instructions. An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Multiple Child Restraint Installation Sequence (Quad Cab威/Crew Cab/Mega Cab威 - Rear Seats) Quad Cab威/Mega Cab威 2 1. Obtain tether straps by raising the head restraints and reaching between the rear glass and rear seat. The tether strap may be retained with an elastic band. Accessibility to the tether strap is greatly improved by raising the seat cushion to the “up” position. Remove the elastic before use. Head Restraint Adjustment 2.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Route each tether strap to the anchor behind the center seat, and attach the hooks to the metal ring. 5. Place a child restraint on the center rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat and to the anchor directly behind the right seat. 6. Install each child restraint and remove the slack in the tether strap according to the child restraint manufacturer’s instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 2. Place a child restraint on each outboard rear seat and adjust the tether strap so that it will reach under the head 1. The tether straps loops are located between the rear glass restraint, through the outboard tether strap loop, then and the rear seat. There is a tether strap loop located behind route it to the tether strap loop located directly behind each seating position. You can gain access to the center the center rear seat.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. Install each child restraint and remove the slack in the Transporting Pets tether strap according to the child restraint manufactur- Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly er’s instructions. injured, or injure a passenger during panic braking or in Children Too Large for Booster Seats a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. For the recommended viscosity and quality grades refer to “Maintenance Procedures” in “Maintaining Your Vehicle”. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow these safety tips: Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to Seat Belts feel the air directed against the windshield. See your Inspect the belt system periodically, checking for cuts, authorized dealer for service if your defroster is frays, and loose parts. Damaged parts must be replaced inoperable. immediately. Do not disassemble or modify the system.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Door Latches Check for positive closing, latching, and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid, or brake fluid leaks are suspected, the cause should be located and corrected immediately.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 ▫ Illuminated Vanity Mirror — If Equipped . . . . 92 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 87 ▫ “Slide-On-Rod” Features Of Sun Visor — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 92 ▫ Automatic Dimming Mirror — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 88 ▫ Trailer Towing Mirrors — If Equipped . . . . . .
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Adjustable Head Restraints . . . . . . . . . . . . . . 97 ▫ Driver Easy Exit And Easy Entry Control . . . 112 ▫ Eight-Way Power Seats — If Equipped . . . . . 100 䡵 To Open And Close The Hood . . . . . . . . . . . . 113 ▫ Power Lumbar — If Equipped . . . . . . . . . . . 101 䡵 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 ▫ Heated Seats — If Equipped . . . . . . . . . . . . 102 ▫ Headlights . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Daytime Running Lights (DRL) (Canada Only And Fleet Vehicles) . . . . . . . . . 121 ▫ Multifunction Lever . . . . . . . . . . . . . . . . . . 121 䡵 Windshield Wipers And Washers . . . . . . . . . . 123 ▫ Windshield Wipers . . . . . . . . . . . . . . . . . . . 123 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . 124 ▫ Mist Feature . . . . . . . . . . . . . . . . . . . . . . . . 124 䡵 Tilt Steering Column . . . . . . . . . . . . . . . . . . .
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Parkview威 Rear Back Up Camera — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 141 ▫ Turning Parkview威 On Or Off — With Navigation/Multimedia Radio . . . . . . . 142 ▫ Turning Parkview威 On Or Off — Without Navigation/Multimedia Radio . . . . . 143 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 ▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . . 151 ▫ General Information . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . 154 䡵 Cigar Lighter And Ash Receiver — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 158 䡵 Power Inverter — If Equipped . . . . . . . . . . . . 159 䡵 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . 161 ▫ Front Instrument Panel Cupholders — (40–20–40 Seats) . . . . . . . . . . . . . . . . . . . . . 161 85 ▫ Center Storage Compartment — If Equipped . . . . . . . . . . . .
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Fold Flat Load Floor — If Equipped . . . . . . . . 173 䡵 Slide-In Campers . . . . . . . . . . . . . . . . . . . . . . 189 䡵 Rambox威 — If Equipped . . . . . . . . . . . . . . . . 175 ▫ Camper Applications . . . . . . . . . . . . . . . . . . 189 ▫ Rambox威 Integrated Box Side Storage Bins . . . . . . . . . . . . . . . . . . . . . . . . 176 䡵 Easy-Off Tailgate . . . . . . . . . . . . . . . . . . . . . . 189 ▫ Rambox威 Safety Warning . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 MIRRORS Inside Day/Night Mirror Headlight glare can be reduced by moving the small control lever under the mirror to the night position (lever flipped toward the rear of vehicle). 3 Adjusting Rearview Mirror The mirror should be adjusted with the lever set in the day position (lever flipped toward the windshield). The mirror should be adjusted to center on the view through the rear window.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the power button at the base of the mirror. A light next to the button will illuminate when the dimming feature is activated. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 WARNING! Vehicles and other objects seen in a passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side convex mirror. Some vehicles will not have a convex right side mirror.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The power mirror controls consist of mirror select butPower Mirrors — If Equipped The controls for the power mirrors are located on the tons and a four-way mirror control switch. driver’s door trim panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 To adjust a mirror, press the mirror select button for the Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This mirror that you want to adjust. Using the mirror control feature is activated whenever you turn on the rear switch, press on any of the four arrows for the direction window defroster. Refer to “Rear Window Features” in that you want the mirror to move. “Understanding the Features of Your Vehicle” for further information.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirror — If Equipped Illuminated vanity mirrors are located on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on automatically. Closing the mirror cover turns off the light. “Slide-On-Rod” Features of Sun Visor — If Equipped The sun visor “Slide-On-Rod” feature allows for additional flexibility in positioning the visor to block out the sun.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or outboard, the mirror head should be rotated (flipped in or out). NOTE: Fold the trailer towing mirrors rearward prior to entering an automated car wash. A small blindspot mirror is located next to main mirror and can be adjusted separately.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect™ Phone — IF EQUIPPED Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details. VOICE COMMAND — IF EQUIPPED Refer to “Voice Command” in the Uconnect™ Phone User Manual located on the DVD for further details. SEATS Seats are a primary part of the Occupant Restraint System of the vehicle. Proper use of the seats is needed for safe operation of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Seat Adjuster — If Equipped Both front seats are independently adjustable forward or rearward and are equipped with a seatback recliner. The manual forward or rearward seat adjustment handle is found under the seat cushion at the front edge of each seat. Pull up on the handle and slide the seat forward or backward to move the seat into the most comfortable position.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. Manual Reclining Seats — If Equipped The recliner handle is located on the outside of the seat cushion and is used to adjust the seatback position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 WARNING! WARNING! (Continued) • Actuating the recliner handle will allow the seatback to swing (dump) forward on manual recliner seats. Do not stand or lean in front of the seat while actuating the handle. The seatback may swing forward and hit you causing injury. This dump feature allows access to the storage bin behind the seat. To avoid injury, place your hand on the seatback and actuate the handle then position the seatback in the desired position.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the large button, located on the base of the head restraint, and push downward on the head restraint. To remove the head restraint, pull upward on the head restraint to it’s highest position, push in both buttons at the base of each head restraint rod, and simultaneously pull up on the head restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 until the head restraint reaches the first lock position, lower the head restraint, press the large button, located push the large button in and push down and adjust head on the base of the head restraint, and push downward on restraint to desired position. the head restraint. NOTE: Ensure that the front of the head restraint is facing toward the front of the vehicle.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Eight-Way Power Seats — If Equipped The power seat controls are on the outboard side of the front seat cushions. The power seat switch can be moved forward and backward as well as up and down to control the position of the seat. The power seatback switch is used to adjust the angle of the seatback to position yourself in the most comfortable driving position. Push forward or rearward on the switch and the seatback will move in either direction.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. 101 Power Lumbar — If Equipped The lumbar controls are located on the outboard side of the seat cushion.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. Heated Seats — If Equipped Both front seats and rear passenger seats can be equipped with heaters. The switches for the front seats are located in the instrument panel under the climate controls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The drivers heated seat can be programmed to come on during a remote start. Refer to “Remote Starting System — If Equipped” in “Things to Know Before Starting Your Vehicle” for further information. WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ventilated Seats — If Equipped Located in the seat cushion and seatback are small fans that draw the air from around the occupant and exhaust it underneath the seat and into the passenger compartment. The fans draw this air across the surface of the seat using air ducts and fine perforations in the covering to help keep the driver cooler in higher ambient temperatures. the switch will be illuminated. When Low speed is selected one light will be illuminated.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mega Cab姞 Rear Seat Features Reclining Rear Seats — If Equipped The recliner handle is located on the outside of the seat cushion. Pull upward on the handle, to release the seatback, and lean forward or rearward to the desired position. Rear Seat Recliner Handle 105 WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Fold the seatback forward. Folding Rear Seat (Table Mode) — If Equipped Both the left and right rear seatbacks can be folded down and used as a table. To fold down either rear seatback: 1. Lift the handle, located next to the head restraint. Table Mode 3. Lift the seatback, to return the seat to the upright position. Be sure the seatback is locked in place.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Cargo must be securely tied down before driving your vehicle.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Fold the seatback down and push the seat forward. 3. Lift the seatback, to return the seat to the upright position. Be sure the seat is locked in place. WARNING! Be certain that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Keyless Entry (RKE) transmitters can also be programmed to recall the same positions when the UNLOCK button is pressed. NOTE: The power lumbar option is not programmable with driver memory seats. Your vehicle was delivered with two RKE transmitters. One or both RKE transmitters can be linked to either memory position. The memory system can accommodate up to two RKE transmitters, each RKE transmitter linked to either of the two memory positions.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Adjust the driver’s seat, recliner, and both sideview performed within 10 seconds if you desire to also use a mirrors to the desired positions. RKE transmitter to recall memory positions. NOTE: Not all motors may be moved at one time. Refer 8. Turn the ignition OFF and remove the key. to “Seats/Eight-Way Power Seat” in this section for 9. Press and release the LOCK button on one of the RKE further information. transmitters. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 • Not all motors may be moved at one time. Refer to the when not in the ignition switch. When a recall is can“Seats/Eight-Way Power Seat” in this section for fur- celled, the driver’s seat and the pedals stop moving. A delay of one second will occur before another recall can ther information. be selected.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The capability to link RKE transmitters to memory is enabled when delivered from the factory. The capability to link RKE transmitters to memory can be disabled (or later re-enabled) by an authorized dealer. For vehicles equipped with the Electronic vehicle Information Center (EVIC), refer to “Electronic Vehicle Information Center (EVIC)/Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Easy Entry/Easy Exit feature can be enabled or disabled through the programmable features in the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/ Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information. 113 3 TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. 1.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Reach into the opening beneath the center of the hood and push the safety latch lever from right to left to release it, before raising the hood. CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. WARNING! Be sure the hood is fully latched before driving your vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS The headlight switch is located on the left side of the instrument panel, next to the steering wheel. The headlight switch controls the operation of the headlights, parking lights, instrument panel lights, cargo lights and fog lights (if equipped). 115 Your vehicle is equipped with plastic headlight and fog light (if equipped) lenses that are lighter and less susceptible to stone breakage than glass lights.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights To turn on the headlights, rotate the headlight switch clockwise. When the headlight switch is on the parking lights, taillights, license plate light and instrument panel lights are also turned on. To turn off the headlights, rotate the headlight switch back to the O (Off) position. Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 NOTE: The engine must be running before the head- 2. Turn the headlight switch to the AUTO headlight position. lights will turn on in the Automatic Mode. SmartBeam™ — If Equipped The SmartBeam™ system provides increased forward lighting at night by automating high beam control through the use of a digital camera mounted on the inside rearview mirror.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlight Delay To aid in your exit, your vehicle is equipped with a headlight delay that will leave the headlights on for approximately 90 seconds. This delay is initiated when the ignition is turned OFF while the headlight switch is on, and then the headlight switch is cycled off. Headlight delay can be cancelled by either turning the headlight switch on then off, or by turning the ignition ON. parking light symbol.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The fog lights will operate only when the parking lights are on or when the vehicle headlights are on low beam. An indicator light located in the instrument cluster will illuminate when the fog lights are on. The fog lights will turn off when the switch is pushed a second time, when the headlight switch is rotated to the off position, or the high beam is selected.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Light Lights-on Reminder The cargo lights are turned on by pressing on the cargo If the headlights, parking lights, or cargo lights are left on button. after the ignition is turned OFF, a chime will sound when the driver’s door is opened. Battery Saver To protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights (DRL) (Canada Only and Fleet Vehicles) The headlights on your vehicle will illuminate when the engine is started and the transmission is in any gear except PARK. This provides a constant ⬙Lights ON⬙ condition until the ignition is turned OFF. The lights illuminate at less than 50% of normal intensity. If the parking brake is applied, the Daytime Running Lights (DRL) will turn OFF.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. High/Low Beam Switch Push the multifunction lever toward the instrument panel to switch the headlights to high beam.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Intermittent Wiper System The intermittent feature of this system was designed for Windshield Wipers use when weather conditions make a single wiping cycle, The wipers and washers are operated by a switch in the with a variable pause between cycles, desirable. For multifunction lever. Turn the end of the handle to select maximum delay between cycles, rotate the control knob the desired wiper speed. into the upper end of the delay range.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Washers WARNING! To use the windshield washer, push the washer knob, located on the end of the multifunction lever, inward to Sudden loss of visibility through the windshield the second detent. Washer fluid will be sprayed until the could lead to an accident. You might not see other washer knob is released from this position. If the washer vehicles or other obstacles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pull the lever toward the steering wheel to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Release the lever to lock the steering column firmly in place. Tilt Steering Lever 125 WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The heated steering wheel switch is located on the switch bank below the climate controls. Press the switch to turn on the heated steering wheel. The light on the switch will illuminate to indicate the steering wheel heater is on. Pressing the switch a second time will turn off the heated steering wheel and light indicator. NOTE: • The engine must be running for the heated steering wheel to operate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 DRIVER ADJUSTABLE PEDALS — IF EQUIPPED The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals. Adjustment 1. Position the driver’s seat so that you are at least 10 in (25.4 cm) away from the airbag, located in the center of the steering wheel. 2. Fasten and adjust the seatbelts. 3.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, Electronic Speed Control takes over the accelerator operation at speeds greater than 25 mph (40 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated simultaneously. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Deactivating Electronic Speed Control A soft tap on the brake pedal or pulling the Electronic Speed Control lever (CANCEL) toward you will deactivate the Electronic Speed Control without erasing the set speed memory. Pushing the ON/OFF button to the OFF position or turning OFF the ignition erases the set speed memory. RESUME ACCEL position, the set speed will continue to increase until the lever is released, then the new set speed will be established.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate for Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on moderate hills is normal. Your vehicle may experience a downshift (automatic transmissions only) while climbing uphill or descending downhill. This downshift is necessary to maintain vehicle set speed.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKSENSE姞 REAR PARK ASSIST — IF EQUIPPED The ParkSense威 Rear Park Assist system provides visual and audible indications of the distance between the rear bumper and the detected obstacle when backing up. Refer to ParkSense威 System Usage and Precautions for limitations of this system and recommendations. ParkSense姞 Sensors The four ParkSense威 sensors, located in the rear bumper, monitor the area behind the vehicle that is within the sensors’ field of view.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 The ParkSense威 Warning Display is located in the instru- When the vehicle is in REVERSE, the warning display ment cluster’s EVIC display. It provides both visual and will turn ON indicating the system status. audible warnings to indicate the distance between the rear bumper and the detected obstacle.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Park Assist Disabled ParkSense威 will indicate a detected obstacle by showing three solid arcs and will produce a 1⁄2 second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 3 Fast Tone Continuous Tone The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING DISPLAY DISTANCES DISPLAY MESSAGE OBSTACLE DISTANCE FROM: REAR CORNERS REAR CENTER ARC’s AUDIBLE SIGNAL Park Assist ON None None Warning Object Detected 78.7 in (200 cm) 3 Solid Yes, 1/2 second Warning Object Detected 39.3 in (100 cm) 3 Flashing Slow Tone Warning Object Detected 27.5 in (70 cm) 31.4 in (80 cm) 3 Flashing Slow Tone Warning Object Detected 25.5 in (65 cm) 25.5 in (65 cm) 2 Flashing Fast Tone Warning Object Detected 19.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Enable/Disable ParkSense姞 ParkSense威 can be enabled and disabled with a switch located in the switch bank of the instrument panel or through the Customer-Programmable Features section of the EVIC. The available choices are: OFF, Sound Only, or Sound and Display. Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (CustomerProgrammable Features (SETUP)” in “Understanding Your Instrument Panel” for further information.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE and the system is disabled, the EVIC will display the If “CLEAN PARK ASSIST SENSORS” appears in the “PARK ASSIST DISABLED” message for as long as the Electronic Vehicle Information Center (EVIC) after making sure the rear bumper is clean and free of snow, ice, vehicle is in REVERSE. mud, or other debris, see your authorized dealer. The switch LED will be ON when ParkSense威 is disabled or defective.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When you turn ParkSense威 off, the instrument cluster will display “PARK ASSIST DISABLED.” Furthermore, once you turn ParkSense威 off, it remains off until you turn it on again, even if you cycle the ignition • key. • When you move the shift lever to the REVERSE position and ParkSense威 is turned off, the instrument cluster will display “PARK ASSIST DISABLED” message for as long as the vehicle is in reverse.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! • The ParkSense威 Rear Park Assist system is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the ParkSense威 sensors will not be detected when they are in close proximity.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Before using the ParkSense威 Rear Park Assist system, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear bumper when the warning display turns on the single flashing arc and sounds the continuous tone.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • To avoid vehicle damage, ParkView威 should only be used as a parking aid. The ParkView威 camera is unable to view every obstacle or object in your drive path. • To avoid vehicle damage, the vehicle must be driven slowly when using ParkView威 to be able to stop in time when an obstacle is seen. It is recommended that the driver look frequently over his/ her shoulder when using ParkView威.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Turning ParkView姞 On or Off — Without Navigation/Multimedia Radio • Courtesy/Reading Lights 1. Press the “menu” hard key. • Power Sliding Rear Window Switch — If Equipped 2. Select “system setup” soft key. • Universal Garage Door Opener — If Equipped • Power Sunroof Switch — If Equipped 3. Enable or disable the rear camera feature by selecting “enable rear camera in reverse” soft key. 4.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy/Reading Lights Both lights in the overhead console and rear passenger compartment will illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (full right position), or when the UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter, if equipped. These lights are also operated individually as reading lights by pressing on the corresponding lens.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 NOTE: The courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. If the interior lights are left on after the ignition is turned OFF, they will extinguish after 15 minutes.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink威 buttons are located in the overhead console, and contain one, two or three dots/lines designating the different HomeLink威 channels. HomeLink威 Buttons NOTE: HomeLink威 is disabled when the Vehicle Security Alarm is active. WARNING! • Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming HomeLink姞 147 2. Place the handheld transmitter 1 to 3 in (3 to 8 cm) from the HomeLink威 buttons while keeping the EVIC display in view. Before You Begin If you have not trained any of the HomeLink威 buttons, erase all channels before you begin training. For optimal training, point the battery end of the handheld transmitter away from the HomeLink威 To do this, press and hold the two outside buttons for 20 seconds.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Some gate operators and garage door openers This can usually be found where the hanging antenna may require you to replace Step 3 with procedures noted wire is attached to the garage door opener motor (it is in the “Gate Operator/Canadian Programming” section. NOT the button normally used to open and close the door). 4. Press and hold the just-trained HomeLink威 button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 6. Firmly press and release the LEARN or TRAINING Gate Operator/Canadian Programming button. The name and color of the button may vary by Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of manufacturer. transmission – which may not be long enough for NOTE: You have 30 seconds in which to initiate the next HomeLink威 to pick up the signal during programming. step after the LEARN button has been pressed.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE successfully accepted the frequency signal. The EVIC 1. Turn the ignition switch to the ON/RUN position. display will change from “CHANNEL # TRAINING” to 2. Press and hold the desired HomeLink威 button for “CHANNEL # TRAINED.” 20 seconds until the EVIC display states “CHANNEL # If you unplugged the device for training, plug it back in TRAINING.” Do not release the button. at this time. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Troubleshooting Tips General Information If you are having trouble programming HomeLink威, here This device complies with FCC rules Part 15 and Industry are some of the most common solutions: Canada RSS-210. Operation is subject to the following two conditions: • Replace the battery in the original transmitter. 1. This device may not cause harmful interference. • Press the LEARN button on the garage door opener to complete the training for rolling code. 2.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The power sunroof switch is located on the overhead console between the courtesy/reading lights. Power Sunroof Switch NOTE: The Power Accessory Delay feature will allow the power sunroof to operate for approximately ten minutes after the ignition is turned OFF or until a front door is opened. WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Open Sunroof — Express Mode Momentarily pressing the switch rearward will activate the Express Open Feature, causing the sunroof to open automatically. During the Express Open operation, any movement of the switch will stop the sunroof and it will remain in a partial open position. Again, momentarily pressing the switch rearward will activate the Express Open Feature.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunshade Operation Sunroof Maintenance The sunshade can be opened manually. However, the Use only a non-abrasive cleaner and a soft cloth to clean sunshade will open automatically as the sunroof opens. the glass panel. NOTE: The sunshade cannot be closed if the sunroof is Sunroof Fully Closed Press the switch forward and release to ensure that the open. sunroof is fully closed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 NOTE: • To ensure proper operation a MOPAR威 knob and element must be used. • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. 3 The auxiliary power outlets can be found in the following locations: • Lower left and lower right of the center stack — without floor mounted shifter.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Inside the upper lid of the center storage compartment — if equipped. Power Outlet — Rear Center Console The key symbol indicates that this outlet can supply power when the key is in the ON/RUN or ACC posiPower Outlet — Upper Lid • Rear of the center console storage compartment — tions. Quad Cab威 or Crew Cab.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE All accessories connected to the outlet(s) should be removed or turned off when the vehicle is not in use to protect the battery against discharge. WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CIGAR LIGHTER AND ASH RECEIVER — IF EQUIPPED A removable ash receiver and cigar lighter are available. For vehicles with a bench seat the cupholder tray can be used to hold the ash receiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE For vehicles equipped with an optional floor shifter. Optional Floor Shifter 1 — Cigar Lighter 2 — Ash Receiver 159 POWER INVERTER — IF EQUIPPED A 115 Volt (150 Watts Maximum) outlet is located on the center stack of the instrument panel, to the right of the radio. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset. If the power rating exceeds approximately 170 Watts, the power inverter may have to be reset manually. To reset the inverter manually press the power inverter button OFF and ON.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • When the power inverter switch is pressed, there will be a delay of approximately one second before the power inverter status indicator turns on. The status indicator of the AC power inverter indicates whether the inverter is producing AC power. CUPHOLDERS Front Instrument Panel Cupholders — (40–20–40 Seats) The cupholders are located in the pull-out tray at the bottom of the center stack.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Instrument Panel Cupholders — Floor Mounted Shifter For vehicles equipped with bucket seats and a floor mounted shifter there are two cupholders located in the floor console. Rear Cupholder — Quad Cab姞 Quad Cab威 vehicles may be equipped with a rear cupholder that consists of two cup wells for rear passenger convenience.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Rear Cupholder — Crew Cab STORAGE Crew Cab vehicles are equipped with rear cupholders Glove Box Storage located in the center armrest. The glove box is located on the passenger side of the instrument panel and features both an upper and lower storage area.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the upper glove box push upward on the handle To open the lower glove box, pull on the handle to release release. The glove box door will automatically open. the latch and lower the door.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Door Storage Front Door Storage — If Equipped Storage areas and bottle holders (drivers side only) are located in the door trim panels. 165 Rear Door Storage — Crew Cab Storage compartments are located in both the driver and passenger door trim panels.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Center Storage Compartment — If Equipped The center storage compartment is located between the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and lower storage area. WARNING! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or an accident. Only use the center seating position when the armrest is fully upright.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 3 Upper Storage Compartment With the upper lid closed, pull on the lower handle to open the lower storage bin.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second Row In-Floor Storage Bin — If Equipped In-floor storage bins are located in front of the second row seats and can be used for extra storage. The storage bins have removable liners that can be easily removed for cleaning. In-Floor Storage Bin And Latch To open in-floor storage bin, lift upward on the handle of the latch and open the lid. NOTE: The front seat may have to be moved forward to fully open the lid.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Seatback Storage Storage (Regular Cab) Located in the back of both the driver and passenger The storage bin is located behind the front seats and runs front seats are pockets that can be used for storage. the length of the cab.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage and Seats (Crew Cab) The Crew Cab models provide additional storage under the rear seats. Lift the seats to access the storage compartment. To open the storage compartments, lift upward on the handle of the latch and open the lid. Crew Cab Storage CAUTION! Always lift the storage compartment lids by using the handle. Failure to lift the lids by using the handle can result in damage to the lids.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time. NOTE: To prevent excessive battery drain, use the rear window defroster only when the engine is operating. CAUTION! Grocery Bag Hooks REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located on the climate control panel.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window. Power Sliding Rear Window — If Equipped The switch for the power sliding rear window is located on the overhead console. Press the left side of the switch to open the glass and the right side of the switch to close the glass.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 Unfolding the Load Floor FOLD FLAT LOAD FLOOR — IF EQUIPPED Quad Cab威 models with a 60/40 rear seat may be 1. Lift the 60/40 seat cushion(s) to the upward position. equipped with a folding load floor. WARNING! 3 Do not operate the vehicle with loose items stored on the load floor. While driving or in an accident you may experience abrupt stopping, rapid acceleration, or sharp turns.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Grasp the knob on the load floor and lift the knob until Positioning the Load Floor for Storage Access Under the load floor unfolds into position. the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor. 3. Lift the load floor up to access storage under the load floor. WARNING! Load Floor In Open Position 3. Reverse the procedure to store the load floor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 RAMBOX姞 — IF EQUIPPED The RamBox威 system is an integrated pickup box storage and cargo management system consisting of three features: • Integrated box side storage bins • Cargo extender/divider • Bed rail tie-down system Load Floor Securing Straps 4. Reverse the procedure to put the load floor back in the secured down position before you operate the vehicle.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE RamBox姞 Integrated Box Side Storage Bins Cargo storage bins are located on both sides of the pickup box. The cargo storage bins provide watertight, lockable, illuminated storage for up to 150 lbs (68 kg) of evenly distributed cargo. CAUTION! Failure to follow the following items could cause damage to the vehicle: • Assure that all cargo inside the storage bins is properly secured. • Do not exceed cargo weight rating of 150 lb (68 kg) per bin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 3 RamBox威 Pushbutton and Lock The interior of the RamBox威 will automatically illuminate when the lid is opened. In addition to the automatic illumination switch, there is a manual on/off switch located at the rear of each storage bin. Pushing the switch once will turn off the bin lights, pushing the switch again will turn the lights back on.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! (Continued) Leaving the lid open for extended periods of time could cause the vehicle battery to discharge. If the lid is required to stay open for extended periods of time, it is recommended that the bin lights be turned off manually using the on/off switch. The RamBox威 storage bins can be locked using the vehicle key. To lock the storage bin, insert the key into the keyhole on the pushbutton and turn clockwise to lock.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 RamBox姞 Safety Warning RamBox威 Storage Bin Cover Emergency Release Carefully follow these warnings to help prevent personal Lever — If Equipped As a security measure, a Storage Bin Cover Emergency injury or damage to your vehicle: Release is built into the storage bin cover latching mechaWARNING! nism. • Always close the storage bin covers when your vehicle is unattended. • Do not allow children to have access to the storage bins.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In the event of an individual being locked inside 1. Make sure the center handle is unlocked using the the storage bin, the storage bin cover can be opened from vehicle key and rotate the center handle vertically to inside of the bin by pulling on the glow-in-the-dark lever release the extender side gates. attached to the storage bin cover latching mechanism.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 2. With the side gates open, position the extender fully 3. Rotate the side gates closed allowing the outboard forward in the bed against the front panel. ends to be positioned in front of the cargo tie down loops.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Rotate the center handle horizontally to secure the side Divider Position The divider position is intended for managing your cargo gates in the closed position. and assisting in keeping cargo from moving around the bed. There are 11 divider slots along the bed inner panels which allow for various positions to assist in managing your cargo. To install the bed extender into a divider position perform the following: 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 3 Center Handle and Lock 1 — Center Handle Lock 2 — Handle 2. With the side gates open, position the extender so the outboard ends align with the intended slots in the sides of the bed. Aligning Gate To Slots 3. Rotate the side gates closed so that the outboard ends are secured into the intended slots of the bed.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Rotate the center handle horizontally to secure the side Extender Position The extender position allows you to load the bed of the gates in the closed position. truck beyond the tail gate. The bed extender will add an additional 15 in (38 cm) in the back of the truck when additional cargo room is needed. The extender position utilizes a locating pin and rotating handle located on both sides of the truck bed near the tailgate. Side Gates Closed 5.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 To install the bed extender into the extender position perform the following: 1. Lower the tailgate. 2. Make sure the center handle is unlocked and rotate the center handle vertically in order to release the extender side gates. 3 3. Fit the end of the side gate ends onto the pin and handle.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Rotate the handles to the horizontal position to secure into place. Locking Tab WARNING! To reduce the risk of potential injury or property damage: • Cargo must be secured. • Do not exceed cargo load rating of your vehicle. • Secure all loads to truck utilizing cargo tie downs. • Extender should not be used as cargo tie down. • When vehicle is in motion do not exceed 150 lbs (68 kg) load on the tailgate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Bed Rail Tie-Down System CAUTION! The maximum load per cleat should not exceed 250 lbs (113 kg) and the angle of the load on each cleat should not exceed 60 degrees above horizontal, or damage to the cleat or cleat rail may occur. 3 There are two adjustable cleats on each side of the bed that can be used to assist in securing cargo.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE out on the cleat and slide it to the detent nearest the To remove the cleats from the utility rail, remove the end desired location. Make sure the cleat is seated in the cap by pushing up on the locking tab, located on the detent and tighten the nut. bottom of the end cap. Slide the cleat off the end of the rail.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE SLIDE-IN CAMPERS 189 Disconnecting the Rear Camera — If Equipped 1. Open the tailgate to access the rear camera connector Camper Applications Certain truck models are not recommended for slide-in bracket located on the rear sill. campers. To determine if your vehicle is excluded, please refer to the “Consumer Information Truck-Camper Loading” document available from your authorized dealer. For safety reasons, follow all instructions in this important document.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Remove the connector bracket from the sill by press- 4. Connect the chassis plug and bracket (provided in the ing inward in the locking tab. glove box) to the chassis wiring harness and insert the bracket back into the sill. 5. Connect the tailgate plug (provided in the glove box) to the tailgate wiring harness to ensure that the terminals do not corrode. 6. Tape the tailgate harness and bracket against the forward-facing surface of the tailgate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 2. Unlatch the tailgate and remove the support cables by 5. Remove the tailgate from the vehicle. releasing the lock tang from the pivot. NOTE: Do not carry the tailgate loose in the truck pickup box. WARNING! To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the overhanging camper compartment and be free of leaks. Locking Tang 3.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 197 ▫ EVIC Displays . . . . . . . . . . . . . . . . . . . . . . 221 䡵 Switch Bank Button Description . . . . . . . . . . . 198 ▫ Distance To Empty (DTE) . . . . . . . . . . . . . . 226 ▫ Upper Switch Bank . . . . . . . . . . . . . . . . . . . 198 ▫ Average Fuel Economy / Fuel Saver Mode — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 227 ▫ Lower Switch Bank . . . . . . . . . . . . . . .
194 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Media Center 730N/430 (RER/REN/RBZ) — AM/FM Stereo Radio And CD/DVD/HDD/ NAV — If Equipped . . . . . . . . . . . . . . . . . . . . 238 ▫ Operating Instructions — Voice Command System — If Equipped . . . . . . . . . . . . . . . . . 238 ▫ Operating Instructions — Uconnect™ phone — If Equipped . . . . . . . . . . . . . . . . . . . . . . 239 ▫ Clock Setting Procedure — RBZ Radio . . . . . 239 ▫ Clock Setting Procedure — RER/REN Radio . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Using This Feature . . . . . . . . . . . . . . . . . . . 266 ▫ Controlling The iPod威 Using Radio Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . 266 ▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . 266 ▫ List Or Browse Mode . . . . . . . . . . . . . . . . . 268 䡵 Uconnect™ Multimedia (Satellite Radio) — If Equipped (REN/RER/RBZ/RES Radios Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270 ▫ System Activation . . . . . . .
196 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Automatic Temperature Control (ATC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 283 ▫ Summer Operation . . . . . . . . . . . . . . . . . . . 288 ▫ Winter Operation . . . . . . . . . . . . . . . . . . . . 288 ▫ Vacation/Storage . . . . . . . . . . . . . . . . . . . . 289 ▫ Window Fogging And Frosting . . . . . . . . . . 289 ▫ Outside Air Intake . . . . . . . . . . . . . . . . . . . 289 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 197 INSTRUMENT PANEL FEATURES 4 1 2 3 4 5 6 — — — — — — Headlight Switch Instrument Cluster Radio Upper Switch Bank Upper Glove Compartment Lower Glove Compartment 7 — 115v Power Inverter Outlet 8 — Power Outlet 9 — Lower Switch Bank 10 — Cup Holders 11 — Climate Controls 12 — Power Outlet/Cigar Lighter 13 14 15 16 — — — — Transfer Case Position Switch Ignition Switch Hood Release Parking Brake Release
198 UNDERSTANDING YOUR INSTRUMENT PANEL SWITCH BANK BUTTON DESCRIPTION Upper Switch Bank 1. TOW/HAUL Refer to “Starting And Operating” for more information. 2. ESP OFF The upper switch bank is located on the center of the Refer to “Starting And Operating” for more information. instrument panel. 3. HAZARD WARNING FLASHER Refer to “What To Do In Emergencies” for more information. 4. 115V POWER INVERTER Refer to “Understanding The Features Of Your Vehicle” for more information. 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 199 1. HEATED SEATS Refer to “Understanding The Features Of Your Vehicle” The lower switch bank is located on the center of the for more information. instrument panel. 2. VENTILATED SEATS Refer to “Understanding The Features Of Your Vehicle” for more information. Lower Switch Bank 3. HEATED STEERING WHEEL Refer to “Understanding The Features Of Your Vehicle” for more information.
200 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — BASE
UNDERSTANDING YOUR INSTRUMENT PANEL 201 INSTRUMENT CLUSTER — PREMIUM 4
202 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS • Check for an inoperative outside light bulb if either indicator remains on and does not flash, or flashes at a rapid rate. 1. Tachometer The Tachometer indicates engine speed in revolutions per minute. 3. Fuel Gauge Shows level of fuel in tank when ignition switch is in the CAUTION! ON position. Do not operate the engine with the tachometer pointer at high RPM for extended periods. Engine damage may occur. 4.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H” and you hear continuous chimes, turn the engine off immediately, and call an authorized dealership for service. WARNING! A hot engine cooling system is dangerous.
204 UNDERSTANDING YOUR INSTRUMENT PANEL 7. Electronic Throttle Control (ETC) Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. The light will come on when the ignition is first turned ON and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. For vehicles equipped with a premium cluster this indicator will display in the Electronic Vehicle Information Center (EVIC).
UNDERSTANDING YOUR INSTRUMENT PANEL 205 12. Electronic Stability Program (ESP) Indicator Light 10. SERV (Service) 4WD The SERV 4WD light monitors the electric shift If this indicator light flashes during acceleration, apply as little throttle as possible. While four-wheel drive system. If the SERV 4WD driving, ease up on the accelerator.
206 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the gauge pointer moves to either extreme of the same as it was before the repair or service. If s/he the gauge, the Check Gauges indicator will illuminate cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the and a single chime will sound. mileage was before the repair or service. It is a good idea 15.
UNDERSTANDING YOUR INSTRUMENT PANEL 207 Vehicle Odometer Messages display the engine hour value. The engine hours will be When the appropriate conditions exist, the following displayed for a period of 30 seconds until the ignition is messages will display in the odometer: turned OFF or the engine is started. ECO . . . . . . . . . . . . . . . . . . . Fuel Saver Indicator Off ECO-ON . . . . . . . . . . . . . . . . Fuel Saver Indicator On door . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
208 UNDERSTANDING YOUR INSTRUMENT PANEL If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a loose gascap indicator Loose will display in the odometer display area. Gascap Tighten the fuel filler cap properly and press Indicator the TRIP button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. damaged, a “noFUSE” message will display in the odometer display area.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 the oil change indicator system (after performing the pass H, the indicator will continuously flash and a scheduled maintenance), refer to the following proce- continuous chime will occur until the engine is allowed to cool. dure: 1. Turn the ignition switch to the ON position (Do not If the light turns on while driving, safely pull over and start the engine). stop the vehicle. If the A/C system is on, turn it off.
210 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: In vehicles with 4.7L or 5.7L engines, the highest available transmission gear is displayed in the lower right corner of the Electronic Vehicle Information Center (EVIC) whenever the Electronic Range Select (ERS) feature is active. Use the +/- selector on the shift lever to activate ERS. Refer to “Automatic Transmission” in “Starting And Operating” for further information.
UNDERSTANDING YOUR INSTRUMENT PANEL 22. Cargo Light The cargo light will illuminate when the cargo light is activated by pressing the cargo light button on the headlight switch. 23. Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-lock Brake System reservoir.
212 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately. Vehicles equipped with the ABS, are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 Center (EVIC). Refer to ”Electronic Vehicle Information possible, and inflate them to the proper pressure. Driving Center (EVIC) — If Equipped” for further information. on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also 25.
214 UNDERSTANDING YOUR INSTRUMENT PANEL When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 Although your vehicle will usually be drivable and not 26. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of need towing, see your authorized dealer for service as an onboard diagnostic (OBDII) system which soon as possible. monitors the emissions and engine control sysCAUTION! tem.
216 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants or wood or cardboard, etc. This could result in death or serious injury to the driver, occupants or others. 27.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 30. Transmission Temperature Warning Light WARNING! This light indicates that there is excessive transmission fluid temperature that might occur In some circumstances a Transmission Temperature with severe usage such as trailer towing.
218 UNDERSTANDING YOUR INSTRUMENT PANEL remain on continuously. Refer to “Occupant Restraints” Center (EVIC). Refer to ”Electronic Vehicle Information in “Things To Know Before Starting Your Vehicle” for Center (EVIC) — If Equipped” for further information. further information. 33. Electronic Stability Program (ESP) Indicator Light / Brake Assist System (BAS) Warning Light 32.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 Center (EVIC). Refer to ”Electronic Vehicle Information Center (EVIC) — If Equipped” for further information. WARNING! If a warning light remains on the system may not be working and you will not have the benefit of ESP or BAS. Under certain driving conditions, where ESP or BAS would be beneficial, you - if you have not adjusted your driving speeds and stopping in or to account for the lack of the feature, may be in accident.
220 UNDERSTANDING YOUR INSTRUMENT PANEL This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel. The EVIC consists of the following: Steering wheel EVIC control button, as it appears on the left side of the steering wheel.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 Steering wheel EVIC control button as • Door(s) Ajar (with a single chime, if vehicle is in it appears on the right side of the motion) steering wheel. • Wrong Key • Damaged Key • Key not programmed Press and release the SELECT button for access • Key In Ignition to main menus, sub menus or to select a • Turn Signal On personal setting in the system setup menu. • RKE Battery Low Press the BACK button to scroll back to a • LOW WASHER FLUID previous menu or sub menu.
222 UNDERSTANDING YOUR INSTRUMENT PANEL • Left Front Turn Signal Light Out EVIC Warning Lights • Left Rear Turn Signal Light Out • Door Ajar This light will turn on to indicate that one or more door may be ajar. • Right Front Turn Signal Light Out • Right Rear Turn Signal Light Out • Park Assist Disabled • Oil Pressure Warning Light This light indicates low engine oil pressure. The light should turn on momentarily when the engine Personal Settings Not Available — Vehicle Not in Park is started.
UNDERSTANDING YOUR INSTRUMENT PANEL • Charging System Light This light shows the status of the electrical charging system. The light should come on when the ignition switch is first turned ON and remain on briefly as a bulb check. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system.
224 UNDERSTANDING YOUR INSTRUMENT PANEL • Engine Temperature Warning Light • SERV 4WD This light warns of an overheated engine condiThe SERV 4WD light monitors the electric shift tion. As temperatures rise and the gauge ap4WD system. If the SERV 4WD light stays on or proaches H, this indicator will illuminate and a comes on during driving, it means that the single chime will sound after reaching a set threshold.
UNDERSTANDING YOUR INSTRUMENT PANEL cycles and the vehicle has been driven several miles at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible. 225 WARNING! In some circumstances a Transmission Temperature Indicator, under continued operation, could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.
226 UNDERSTANDING YOUR INSTRUMENT PANEL Oil Change Due Your vehicle is equipped with an engine oil change indicator system. The Oil Change Due message will flash in the EVIC display for approximately 10 seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty-cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 When the DTE value is less than 30 miles (48 km) will appear whenever MDS (if equipped) allows the estimated driving distance, the DTE display will change engine to operate on four cylinders, or if you are driving to a text display of ⬙LOW FUEL.⬙ This display will in a fuel efficient manner. continue until the vehicle runs out of fuel. Adding a significant amount of fuel to the vehicle will turn off the ⬙LOW FUEL⬙ text and a new DTE value will display.
228 UNDERSTANDING YOUR INSTRUMENT PANEL Trip Functions • Trip B Press and release the ODOMETER/TRIP ODOMETER Shows the total distance traveled for Trip B since the last button until one of the following Trip Functions displays reset. in the EVIC: • Elapsed Time • Trip A Shows the total elapsed time of travel since the last reset when the ignition switch is in the ACC position. Elapsed • Trip B time will increment when the ignition switch is in the ON • Elapsed Time or START position.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 System (Customer Information Features) Compass / Temperature Display Press and release the UP or DOWN button until “SYSThe compass readings indicate the direction TEM” displays in the EVIC and press the SELECT button. the vehicle is facing.
230 UNDERSTANDING YOUR INSTRUMENT PANEL blocked or reduced airflow to the underhood ambient temperature sensor caused by the snowplow. In addition, on vehicles equipped with Automatic Temperature Control (ATC), it is suggested that the interior cabin temperature be manually controlled should the system not perform as desired while in automatic mode. Both the outside temperature display and ATC operation will return to normal when the snowplow is removed.
UNDERSTANDING YOUR INSTRUMENT PANEL 231 5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the “CAL” indicator turns off. The compass will now function normally. Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To compensate for the differences the variance should be set for the zone where the vehicle is driven, per the zone map.
232 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Press the DOWN button until the “Compass Variance” Use the UP or DOWN button to display one of the message is displayed in the EVIC, then press the SELECT following choices. button. The last variance zone number displays in the Select Language EVIC. When in this display you may select one of five lan4. Press and release the SELECT button until the proper guages for all display nomenclature, including the trip functions and the navigation system (if equipped).
UNDERSTANDING YOUR INSTRUMENT PANEL 233 the feature showing the system has been activated or the Auto Lock Doors check-mark is removed, showing the system has been When this feature is selected, all doors will lock automatically when the vehicle reaches a speed of 15 mph deactivated. (24 km/h).
234 UNDERSTANDING YOUR INSTRUMENT PANEL 1st Press RKE When Driver Door 1st Press is selected, only the driver’s door will unlock on the first press of the RKE transmitter UNLOCK button. When Driver Door 1st Press is selected, you must press the RKE transmitter UNLOCK button twice to unlock the passenger’s doors. When All Doors 1st Press is selected, all of the doors will unlock on the first press of the RKE transmitter UNLOCK button.
UNDERSTANDING YOUR INSTRUMENT PANEL 235 is pressed. To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed, showing the system has been deactivated. with or without the sound horn on lock feature selected.
236 UNDERSTANDING YOUR INSTRUMENT PANEL a check-mark appears next to the feature showing the or the check-mark is removed, showing the system has system has been activated or the check-mark is removed, been deactivated. When this feature is deactivated, the system reverts to the standard intermittent wiper showing the system has been deactivated. operation.
UNDERSTANDING YOUR INSTRUMENT PANEL Tilt Mirror In Reverse When this feature is selected and the shift lever is placed in reverse gear, the side mirrors tilt downward to allow the driver to see into the previous blind spot and avoid objects in close proximity to the rear of the vehicle. To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed, showing the system has been deactivated.
238 UNDERSTANDING YOUR INSTRUMENT PANEL Display Fuel Saver — If Equipped The “Fuel Saver Mode” message is located in the Compass/Temperature display, this message can be turned on or off. To make your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears. Display Units of Measure In The EVIC, odometer, and navigation system (if equipped) can be changed between English and Metric units of measure.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 Operating Instructions — Uconnect™ Phone — If displayed. To move the minute backward, touch the screen where the word “Min” with the arrow pointing Equipped Refer to “Uconnect™ Phone” in the Uconnect™ User downward is displayed. Manual located on the DVD for further details. 5. To save the new time setting, touch the screen where the word “Save” is displayed.
240 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Touch the screen where the words “Set Time Zone” are Show Time if Radio is Off When selected, this feature will display the time of day displayed. The time zone selection menu will appear on on the touch screen when the radio is turned off. Proceed the screen. as follows to change the current setting: 4. Select a time zone by touching the screen where your selection appears. If you do not see a time zone that you 1. Turn on the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL To Manually Set the Clock — RER/REN 1. Turn on the radio. 2. Touch the screen where the time is displayed. 3. Touch the screen where “User Clock” is displayed, the clock setting menu will appear on the screen. 4. To move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is displayed. To move the hour backward, touch the screen where the word “Hour” with the arrow pointing downward is displayed. 241 6.
242 UNDERSTANDING YOUR INSTRUMENT PANEL Show Time if Radio is Off Changing the Time Zone When selected, this feature will display the time of day 1. Turn on the radio. on the touch screen when the radio is turned off. Proceed 2. Touch the screen where the time is displayed. as follows to change the current setting: 1. Turn on the radio. 2. Touch the screen where the time is displayed. 3. Touch the screen where “User Clock” is displayed, the clock setting menu will appear on the screen. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 130 (RES) — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) 243 Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC NOTE: The radio sales code is located on the lower right position to operate the radio. side of the radio faceplate. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
244 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save time change. 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the AM/FM Button mid-range tones. Press the buttons to select either AM or FM mode. Push the rotary TUNE/SCROLL control knob a third SET/RND Button — To Set the Pushbutton time and TREBLE will display.
246 UNDERSTANDING YOUR INSTRUMENT PANEL SET 2 in both AM and FM. This allows a total of 12 AM Operation Instructions — CD MODE For CD And and 12 FM stations to be stored into pushbutton memory. MP3 Audio Play The stations stored in SET 2 memory can be selected by NOTE: pressing the pushbutton twice. • The ignition switch must be in the ON or ACC position to operate the radio. Every time a preset button is used, a corresponding button number will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 If you insert a disc with the ignition ON and the radio EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. If you have ejected a disc and have not removed it within CAUTION! 10 seconds, it will be reloaded.
248 UNDERSTANDING YOUR INSTRUMENT PANEL the current selection. Pressing and holding the SEEK SET/RND Button (Random Play Button) button will allow faster scrolling through the tracks in Press this button while the CD is playing to activate Random Play. This feature plays the selections on the CD and MP3 modes. compact disc in random order to provide an interesting TIME Button change of pace. Press this button to change the display from a large CD playing time display to a small CD playing time display.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 exceeding 20 folders will result in this display. With Supported Medium Formats (File Systems) 200 files, exceeding 50 folders will result in this The medium formats supported by the radio are ISO 9660 display.) Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than • Maximum number of characters in file/folder names: ISO 9660 Level 1 and Level 2, the radio may fail to read • Level 1: 12 (including a separator ⬙.
250 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 Loading times for playback of MP3 files may be affected MP3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the by the following: vehicle speakers. • Media - CD-RW media may take longer to load than Pressing the DISC/AUX button will change the mode to CD-R media auxiliary device if the AUX jack is connected.
252 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 130 (RES/RSC) — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) AND SIRIUS RADIO Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate. Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. 253 Phone Button Uconnect™ Phone — If Equipped Press this button to operate the Uconnect™ Phone feature (if equipped). Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details.
254 UNDERSTANDING YOUR INSTRUMENT PANEL 3. After adjusting the hours, press the right side TUNE/ INFO Button SCROLL control knob to set the minutes. The minutes Press the INFO button for an RDS station (one with call letters displayed). The radio will return a Radio Text will begin to blink. message broadcast from an FM station (FM mode only). 4. Adjust the minutes using the right side TUNE/ SCROLL control knob.
UNDERSTANDING YOUR INSTRUMENT PANEL Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the bass tones. 255 Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and rear speakers.
256 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the MUSIC TYPE button to select the following format types: Program Type No program type or undefined Adult Hits Classical Classic Rock College Country Foreign Language Information Jazz News Nostalgia Oldies 16-Digit Character Display None Adlt Hit Classicl Cls Rock College Country Language Inform Jazz News Nostalga Oldies Program Type Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk To
UNDERSTANDING YOUR INSTRUMENT PANEL 257 the minutes using the right side TUNE/SCROLL By pressing the SEEK button when the Music Type icon control knob. Press the TUNE/SCROLL control knob is displayed, the radio will be tuned to the next frequency to save time change. station with the same selected Music Type name. The Music Type function only operates when in the FM AM/FM Button mode. Press the button to select either AM or FM mode.
258 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET/RND button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 If you insert a disc with the ignition ON and the radio EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. If you have ejected a disc and have not removed it within CAUTION! 10 seconds, it will be reloaded.
260 UNDERSTANDING YOUR INSTRUMENT PANEL the current selection. Pressing and holding the SEEK SET/RND Button (Random Play Button) button will allow faster scrolling through the tracks in Press this button while the CD is playing to activate Random Play. This feature plays the selections on the CD and MP3 modes. compact disc in random order to provide an interesting TIME Button change of pace. Press this button to change the display from a large CD playing time display to a small CD playing time display.
UNDERSTANDING YOUR INSTRUMENT PANEL 261 exceeding 20 folders will result in this display. With Supported Medium Formats (File Systems) 200 files, exceeding 50 folders will result in this The medium formats supported by the radio are ISO 9660 display.) Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than • Maximum number of characters in file/folder names: ISO 9660 Level 1 and Level 2, the radio may fail to read • Level 1: 12 (including a separator ⬙.
262 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 263 Loading times for playback of MP3 files may be affected begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain by the following: playable files). • Media - CD-RW media may take longer to load than The folder list will time out after five seconds.
264 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack which allows the user to plug in a portable device such as an MP3 player or cassette player and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Operating Instructions - Uconnect™ Phone (If Equipped) Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details.
UNDERSTANDING YOUR INSTRUMENT PANEL 265 This feature allows you to plug an iPod威 into the Connecting The iPod姞 vehicle’s sound system through a 16–pin connector, using Use the provided connection cable to connect an iPod威 to the vehicle’s 16–pin connector port (which is located in the provided interface cable. the glove compartment on some vehicles). Once the UCI supports Mini, 4G, Photo, Nano, 5G iPod威 and iPod威 is connected and synchronized to the vehicle’s UCI iPhone威 devices.
266 UNDERSTANDING YOUR INSTRUMENT PANEL Using This Feature Play Mode By using the provided connection cable to connect an When switched to UCI mode, the iPod威 automatically iPod威 to the vehicle’s UCI 16–pin connector port: starts Play mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 267 • Jump backward in the current track by pressing and • While a track is playing, press the INFO button to see holding the << RW button. Holding the << RW the associated metadata (artist, track title, album, etc.) button long enough will take you to the beginning for that track. Pressing the INFO button again jumps of the current track. to the next screen of data for that track.
268 UNDERSTANDING YOUR INSTRUMENT PANEL • RND button (available on sales code RES radio only): Pressing this button toggles between Shuffle ON and Shuffle OFF modes for the iPod威. If the RND icon is showing on the radio display, then the shuffle mode is ON. List Or Browse Mode During Play mode, pressing any of the buttons described below, takes you to List mode. List mode enables you to scroll through the list of menus and tracks on the iPod威.
UNDERSTANDING YOUR INSTRUMENT PANEL • Pressing a PRESET button will display the current list on the top line and the first item in that list on the second line. • To Exit List mode without selecting a track, press the same PRESET button again to go back to Play mode. • LIST button: The LIST button will display the top level menu of the iPod威. Turn the TUNE control knob to list the top-menu item you wish to select and press the TUNE control knob.
270 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect™ Multimedia (SATELLITE RADIO) — IF EQUIPPED (REN/RER/RBZ/RES RADIOS ONLY) Satellite radio uses direct satellite-to-receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius Satellite Radio. This service offers over 130 channels of music, sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 Sirius ID number will display. The Sirius ID number bikes should be placed as far rearward as possible, within display will time out in two minutes. Press any button on the loading design of the rack. Do not place items directly on or above the antenna. the radio to exit this screen. ESN/SID Access With REN/RER/RBZ Radios Reception Quality While in SAT mode, press the MENU button on the radio Satellite reception may be interrupted due to one of the faceplate.
272 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button Pressing the INFO button will cycle the display information between Artist, Song Title, and Composer (if availNOTE: The ignition switch must be in the ON or ACC able). Also, pressing and holding the INFO button for an position to operate the radio. additional three seconds will make the radio display the SEEK Buttons Song Title all of the time (press and hold again to return Press and release the SEEK buttons to search for the next to normal display).
UNDERSTANDING YOUR INSTRUMENT PANEL MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be selected. 273 SETUP Button Pressing the SETUP button allows you to select the following items: • Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number.
274 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second channel to each pushbutton by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2. This allows a total of 12 Satellite channels to be stored into pushbutton memory. The channels stored in SET 2 memory can be selected by pressing the pushbutton twice.
UNDERSTANDING YOUR INSTRUMENT PANEL 275 The LCD screen is located in the overhead compartment console. 4 VES™ Remote Control Location Overhead Video Screen NOTE: Refer to the “Uconnect™ Multimedia” section of Uconnect™ User Manual located on the DVD for further details.
276 UNDERSTANDING YOUR INSTRUMENT PANEL REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a rocker type switch with a pushbutton in the center. Pressing the top of the switch will increase the volume, and pressing the bottom of the switch will decrease the volume.
UNDERSTANDING YOUR INSTRUMENT PANEL 277 The button located in the center of the left hand control CD/DVD DISC MAINTENANCE will tune to the next pre-set station that you have To keep a CD/DVD in good condition, take the following precautions: programmed in the radio pre-set pushbuttons. CD Player Pressing the top of the switch once will go to the next track on the CD.
278 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particular disc, it may be damaged (i.e., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service. throughout the vehicle. The controls are located on the instrument panel below the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 279 dials and inner push knobs. These comfort controls can Front Blower Control There are four blower speeds. Use this be set to obtain desired interior conditions. control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the OFF position.
280 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If your air conditioning performance seems Panel Mode Air is directed through the outlets in the instrument lower than expected, check the front of the A/C conpanel. These outlets can be adjusted to direct airflow. denser (located in front of the radiator), for an accumulation of dirt or insects. Clean with a gentle water spray Bi-Level Mode from behind the radiator and through the condenser. Air is directed through the panel and floor outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 281 Mix Mode Recirculation Control Air is directed through the floor, defrost and side Press this button to choose between window demist outlets. This setting works best in outside air intake or recirculation of cold or snowy conditions that require extra heat at the air inside the vehicle. A LED will the windshield. This setting is good for maintaining illuminate when you are in Recirculacomfort, while reducing moisture on the windshield. tion mode.
282 UNDERSTANDING YOUR INSTRUMENT PANEL • Continuous use of the Recirculation mode may make NOTE: For maximum airflow to the rear, the center the inside air stuffy and window fogging may occur. instrument panel outlets can be directed toward the rear seat passengers. Extended use of this mode is not recommended. • In cold or damp weather, the use of the Recirculation mode will cause windows to fog on the inside because of moisture buildup inside the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL MAX A/C 283 Automatic Temperature Control (ATC) — If For maximum cooling, when MAX Equipped A/C is selected the A/C is turned on • The Automatic Temperature Control (ATC) allows automatically and the air is recircuboth driver and front passenger seat occupants to lated. select individual comfort settings.
284 UNDERSTANDING YOUR INSTRUMENT PANEL • The system can be controlled manually, if desired. • SYNC feature links the temperature controls, the passenger side temperature becomes the same as the temperature selected by the driver. The ATC system automatically maintains the interior comfort level desired by the driver and all passengers.
UNDERSTANDING YOUR INSTRUMENT PANEL 285 NOTE: • It is not necessary to move the temperature settings for 1. Position the MODE control knob to the Auto position cold or hot vehicles. The system automatically adjusts on the Automatic Temperature Control (ATC) Panel. the temperature, mode and fan speed to provide 2. Position the BLOWER control knob in the Auto posicomfort as quickly as possible. tion on the ATC Panel. • The temperature can be displayed in U.S.
286 UNDERSTANDING YOUR INSTRUMENT PANEL blower will engage immediately if the Defrost mode is The blower fan speed can be set to any fixed speed by selected, or by adjusting the blower control knob and adjusting the blower control knob. The fan will now operate at a fixed speed until additional speeds are setting the fan to any fixed speed. selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 287 NOTE: In many temperature positions, the BI-LEVEL NOTE: While operating in the other modes, the system mode is designed to provide cooler air out of the panel will not automatically sense the presence of fog, mist or ice on the windshield. Defrost mode must be manually outlets and warmer air from the floor outlets. selected to clear the windshield and side glass. Floor Mode Air comes from the floor outlets.
288 UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation Control When outside air contains smoke, odors, or high humidity, or if rapid cooling is desired, you may wish to recirculate interior air by pressing the RECIRCULATION control button. Recirculation mode should only be used temporarily. The recirculation LED will illuminate on the blower control knob when this button is selected. Push the button a second time to turn off the Recirculation mode LED and allow outside air into the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL Vacation/Storage Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in fresh air with the blower setting in high. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. Window Fogging and Frosting Vehicle windows tend to fog on the inside of the glass in mild, rainy and/or humid weather.
290 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 297 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 297 ▫ Automatic Transmission . . . . . . . . . . . . . . . 297 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . 298 ▫ After Starting . . . . . . . . . . . . . . . . . . . . . . . 299 䡵 Engine Block Heater — If Equipped . . . . . . . . 299 䡵 Automatic Transmission . . . . . . . . . . . . . . . . . 300 ▫ Key Ignition Park Interlock . . . . . .
292 STARTING AND OPERATING ▫ Shifting Procedure – Manually Shifted Transfer Case . . . . . . . . . . . . . . . . . . . . . . . 317 ▫ Transfer Case Position Indicator Light . . . . . . 318 ▫ Electronically Shifted Transfer Case (Four-Position Switch) – If Equipped . . . . . . . 318 ▫ Shifting Procedure . . . . . . . . . . . . . . . . . . . 322 ▫ Electronically Shifted Transfer Case (Five-Position Switch) – If Equipped . . . . . . . 324 ▫ Shifting Procedure . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 䡵 Driving Off-Road 293 . . . . . . . . . . . . . . . . . . . . . 355 ▫ Four-Wheel Anti-Lock Brake System . . . . . . . 380 䡵 Winch Usage (Power Wagon Only) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 356 䡵 Electronic Brake Control System . . . . . . . . . . . 382 ▫ Things To Know Before Using Your Winch . . 356 ▫ Understanding The Features Of Your Winch . . . . . . . . . . . . . . . . . . . . . . 358 ▫ Winch Accessories . . . . . . . . . . . . . . . . . .
294 STARTING AND OPERATING 䡵 Tires — General Information . . . . . . . . . . . . . 404 䡵 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 414 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . 404 䡵 Tire Rotation Recommendations . . . . . . . . . . . 414 ▫ Tire Inflation Pressures . . . . . . . . . . . . . . . . 405 ▫ Dual Rear Wheels . . . . . . . . . . . . . . . . . . . . 416 ▫ Tire Pressures For High Speed Operation . . . 407 䡵 Tire Pressure Monitor System (TPMS) . . . .
STARTING AND OPERATING 295 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . 428 ▫ Cruising Range . . . . . . . . . . . . . . . . . . . . . . 435 ▫ E-85 Usage In Non-Flex Fuel Vehicles . . . . . . 428 ▫ Replacement Parts . . . . . . . . . . . . . . . . . . . 435 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . 429 ▫ Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 435 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . 429 䡵 Adding Fuel . . . . . . . . . . . . . . . . . .
296 STARTING AND OPERATING ▫ Towing Requirements . . . . . . . . . . . . . . . . . 447 ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . 455 䡵 Snowplow . . . . . . . . . . . . . . . . . . . . . . . . . . 457 ▫ 1500 Models Only . . . . . . . . . . . . . . . . . . . . 457 ▫ 2500/3500 Models Only . . . . . . . . . . . . . . . . 457 䡵 Recreational Towing (Behind Motorhome, Etc.) . . . . . . . . . . . . . . . . 461 ▫ Recreational Towing – Two-Wheel Drive Models . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 297 STARTING PROCEDURES Normal Starting Before starting your vehicle, adjust your seat, adjust both Normal starting of either a warm or cold engine is inside and outside mirrors, and fasten your seat belt. obtained without pumping or pressing the accelerator pedal. Turn the key fob to the START position and release The starter should not be operated for more than 15when the engine starts. If the engine fails to start within second intervals.
298 STARTING AND OPERATING Tip Start Feature Do not press the accelerator. Turn the ignition switch briefly to the START position and release it. The starter motor will continue to run but will automatically disengage when the engine is running. If Engine Fails To Start If the engine fails to start after you have followed the “Normal Starting” procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine.
STARTING AND OPERATING If the engine has been flooded, it may start to run, but not have enough power to continue running when the key fob is released. If this occurs, continue cranking with the accelerator pedal pushed all the way to the floor. Release the accelerator pedal and the key fob once the engine is running smoothly. 299 1500 Models The engine block heater cord is routed under the hood on the passenger side of the vehicle near the right head lamp assembly.
300 STARTING AND OPERATING WARNING! CAUTION! (Continued) Remember to disconnect the cord before driving. Damage to the 110-115 Volt electrical cord could cause electrocution. AUTOMATIC TRANSMISSION • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly on the brake pedal.
STARTING AND OPERATING Key Ignition Park Interlock This vehicle is equipped with a Key Ignition Park Interlock which requires the shift lever to be placed in PARK prior to turning the key fob to the LOCK position. The key fob can only be removed from the ignition switch when the ignition is in the LOCK position and once removed the shift lever is locked in PARK.
302 STARTING AND OPERATING 5. Using the screwdriver, press and hold the override tab Center Console Shifter – If Equipped through the access port (ringed circle) on the bottom of There is an override for the BTSI that allows you to move the shift lever out of the PARK position if an electrical the steering column. system malfunction occurs (i.e., dead battery).
STARTING AND OPERATING 303 Four–Speed Automatic Transmission – If Equipped NOTE: Under extremely cold temperatures (-6°F (-21°C) and when in DRIVE, transmission operation may be briefly limited to only second gear operation. Normal operation will resume once the transmission temperature has risen to a suitable level. Shifting from DRIVE to PARK or REVERSE should be done only after the accelerator pedal is released and the vehicle is stopped.
304 STARTING AND OPERATING Never use PARK while the vehicle is in motion. Apply REVERSE the parking brake when leaving the vehicle in this range. This range is for moving the vehicle rearward. Use this Always apply the parking brake first, then place the shift range only after the vehicle has come to a complete stop. lever in the PARK position. NEUTRAL This range is used when the vehicle is standing for WARNING! prolonged periods with the engine running.
STARTING AND OPERATING 305 2 (Second) • the engine coolant has reached normal operating temThis range is for moderate grades and to assist braking perature on dry pavement or in mud and snow. Begins at a stop in • vehicle speed is above approximately 30 mph low gear with automatic upshift to second gear. Will not (48 km/h) shift to third gear.
306 STARTING AND OPERATING Temperature Warning Light” may illuminate and the transmission may downshift out of OVERDRIVE until the transmission cools down. After the transmission cools down, the transmission will resume normal operation. The transmission will downshift from OVERDRIVE to DRIVE if the accelerator pedal is fully pressed at vehicle speeds above approximately 35 mph (56 km/h). When To Use TOW/HAUL Mode When driving in hilly areas, towing a trailer, carrying a heavy load, etc.
STARTING AND OPERATING Transmission Limp Home Mode Transmission function is monitored for abnormal conditions. If a condition is detected that could result in transmission damage, the Transmission Limp Home Mode will be engaged. In this mode, the transmission will remain in the current gear until the vehicle is brought to a stop. To reset the transmission, use the following procedure: 1. Stop the vehicle. 2. Move the shift lever to the PARK position. 3.
308 STARTING AND OPERATING into 3 (third gear), the transmission will never shift above Five–Speed Automatic Transmission – If third gear, but can shift down to 2 (second gear) or 1 (first Equipped The shift lever display located in the instrument panel gear), when needed. cluster indicates the transmission gear range. The shift lever is mounted either on the right side of the steering column (if equipped) or on the floor console (if equipped).
STARTING AND OPERATING 309 through third gear are underdrive gears, and fourth gear is direct drive. ERS fifth gear (Overdrive) is the same as the normal fourth gear. When in the DRIVE position in first through fourth gear, the first tap down (-), will display the ERS designation for the current gear (the transmission will not downshift).
310 STARTING AND OPERATING WARNING! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid. Gear Ranges Do not race the engine when shifting from PARK or NEUTRAL position into another gear range. PARK This range supplements the parking brake by locking the transmission. The engine can be started in this range. Screen Display 1 2 3 4 5* D Never use PARK while the vehicle is in motion.
STARTING AND OPERATING WARNING! (Continued) • Your vehicle could move and injure you and others if it is not completely in PARK. Check by trying to move the shift lever back and forth without first pulling it toward you after you have set it in PARK. Make sure it is in PARK before leaving the vehicle. • It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed.
312 STARTING AND OPERATING • the engine coolant (antifreeze) has reached normal Temperature Warning Light” may illuminate and the transmission may downshift out of Overdrive until the operating temperature; transmission cools down. After cool down, the transmis• vehicle speed is above approximately 30 mph sion will resume normal operation.
STARTING AND OPERATING 313 activated. Pressing the switch a second time restores normal operation. If the TOW/HAUL mode is desired, the button must be pressed each time the engine is started. TOW/HAUL Switch Torque Converter Clutch A feature designed to improve fuel economy has been included in the automatic transmission on your vehicle. A clutch within the torque converter engages automatically at calibrated speeds.
314 STARTING AND OPERATING torque converter clutch is not engaged, it may seem as if the transmission is not shifting into Overdrive when cold. This is normal. Pressing the TOW/HAUL switch when the transmission is sufficiently warm will demonstrate that the transmission is able to shift into and out of Overdrive. • If the vehicle has not been driven in several days, the first few seconds of operation after shifting the transmission into gear may seem sluggish.
STARTING AND OPERATING moving the shift lever to the desired positions. The 4H and 4L positions are intended for loose, slippery road surfaces only. Driving in the 4H and 4L positions on dry, hard surfaced roads may cause increased tire wear and damage to the driveline components. The “Transfer Case Position Indicator Light” in the instrument cluster will alert the driver that the vehicle is in four-wheel drive and that the front and rear driveshafts are locked together.
316 STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake. The transfer case NEUTRAL position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position. The parking brake should always be applied when the driver is not in the vehicle.
STARTING AND OPERATING 317 NOTE: • Pausing in transfer case NEUTRAL in vehicles equipped with an automatic transmission may require 2H ⇔ 4H shutting the engine OFF to avoid gear clash while Shifting between 2H and 4H can be made with the completing the shift. If difficulty occurs, shift the vehicle stopped or in motion. If the vehicle is in motion, transmission into NEUTRAL, hold foot on brake, and shifts can be made up to 55 mph (88 km/h). With the turn the engine OFF. Make shift to the desired mode.
318 STARTING AND OPERATING Transfer Case Position Indicator Light The “Transfer Case Position Indicator Light” in the instrument cluster is used to alert the driver that the front axle is fully engaged and all four wheels are driving. Electronically Shifted Transfer Case (Four-Position Switch) – If Equipped This is an electronic shift transfer case and is operated by the 4WD Control Switch (Transfer Case Switch), which is located on the instrument panel.
STARTING AND OPERATING 319 • Neutral (NEUTRAL) NOTE: The transfer case NEUTRAL position is selected by pressing the recessed button located on the lower left This electronically shifted transfer case is designed to be hand corner of the 4WD Control Switch. The transfer case driven in the two-wheel drive position (2WD) for normal NEUTRAL position is to be used for recreational towing street and highway conditions on dry, hard surfaced only. Refer to “Recreational Towing” in “Starting and roads.
320 STARTING AND OPERATING 3. When the shift is complete, the indicator light for the The “SVC 4WD Warning Light” monitors the electronic selected position will stop flashing and remain ON. shift four-wheel drive system. If this light remains on after engine start up or illuminates during driving, it If One Or More Shift Conditions Are Not Met: means that the four-wheel drive system is not function1. The indicator light for the current position will remain ing properly and that service is required. ON. 2.
STARTING AND OPERATING When operating your vehicle in 4WD LOW, the engine speed is approximately three times that of the 2WD or 4WD LOCK positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the transfer case.
322 STARTING AND OPERATING 4WD LOCK Shifting Procedure Four-Wheel Drive Lock Range - This range locks the front NOTE: and rear driveshafts together forcing the front and rear • If any of the requirements to select a new transfer case wheels to rotate at the same speed. This range provides position have not been met, the transfer case will not additional traction for loose, slippery road surfaces only. shift.
STARTING AND OPERATING 323 When the shift is complete, the position indicator light selected position indicator light will flash and the origifor the selected position will stop flashing and remain nal position indicator light will remain ON. At this time, reduce speed and stop spinning the wheels to complete ON. the shift. 2WD⇔ 4WD LOCK Rotate the 4WD control switch to the desired position.
324 STARTING AND OPERATING 3. While still rolling, rotate the transfer case control NOTE: • If Steps 1 or 2 of either the Preferred or Alternate switch to the desired position. Procedure are not satisfied prior to attempting the 4. After the desired position indicator light is ON (not shift, then the desired position indicator light will flash flashing), shift the transmission back into gear. continuously while the original position indicator light is ON, until all requirements have been met.
STARTING AND OPERATING 325 • Four-wheel drive low range (4WD LOW) • Neutral (NEUTRAL) This electronically shifted transfer case is designed to be driven in the two–wheel drive position (2WD) or fourwheel drive position (4WD AUTO) for normal street and highway conditions on dry hard surfaced roads). Driving the vehicle in 2WD will have greater fuel economy benefits as the front axle is not engaged in 2WD. For variable driving conditions, the 4WD AUTO mode can be used.
326 STARTING AND OPERATING the front and rear driveshafts together forcing the front and rear wheels to rotate at the same speed. This is accomplished by rotating the 4WD Control Switch to the desired position. Refer to “Shifting Procedure” for specific shifting instructions. The 4WD LOCK and 4WD LOW positions are designed for loose, slippery road surfaces only. Driving in the 4WD LOCK and 4WD LOW positions on dry hard surfaced roads may cause increased tire wear and damage to the driveline components.
STARTING AND OPERATING 2. The newly selected position indicator light will continue to flash. 3. The transfer case will not shift. 327 WARNING! Always engage the parking brake when powering down the vehicle if the “SVC 4WD Warning Light” is illuminated. Not engaging the parking brake may allow the vehicle to roll which may cause personal injury. NOTE: Before retrying a selection, make certain that all the necessary requirements for selecting a new transfer case position have been met.
328 STARTING AND OPERATING Proper operation of four-wheel drive vehicles depends For additional information on the appropriate use of each on tires of equal size, type and circumference on each transfer case mode position, see the information below: wheel. Any difference in tire size can cause damage to the 2WD transfer case. Rear-Wheel Drive High Range - This range is for normal Because four-wheel drive provides improved traction, street and highway driving on dry hard surfaced roads.
STARTING AND OPERATING 4WD LOW Four-Wheel Drive Low Range - This range provides low speed four-wheel drive. Locks the front and rear driveshafts together forcing the front and rear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). 329 position will remain ON, and the newly selected position indicator light will continue to flash until all the requirements for the selected position have been met.
330 STARTING AND OPERATING the vehicle in motion, the transfer case will engage/ disengage faster if you momentarily release the accelerator pedal after turning the control switch. If the vehicle is stopped, the ignition switch must be in the ON position with the engine either running or OFF. This shift cannot be completed if the ignition switch is in the ACC position. 2. Shift the transmission into NEUTRAL. 2WD or 4WD AUTO or 4WD LOCK ⇔ 4WD LOW Alternate Procedure 3.
STARTING AND OPERATING NOTE: If Steps 1 or 2 of either the Preferred or Alternate Procedure are not satisfied prior to attempting the shift or if they no longer are being met while the shift attempt is in process, the desired position indicator light will flash continuously while the original position indicator light is ON, until all requirements have been met. NOTE: The ignition switch must be in the ON position for a shift to take place and for the position indicator lights to be operable.
332 STARTING AND OPERATING The locking axles are controlled by the axle locker switch. To lock the rear axle, place the vehicle in 4LO. Refer to “Four Wheel Drive Operation” in “Starting and OperatThe switch has three positions, AXLE UNLOCK, REAR ing” for further information. Move the axle locker switch LOCK, and FRONT/REAR LOCK. Under normal drivposition to REAR LOCK while traveling less than 3 mph ing conditions, the switch should be left in the AXLE (5 km/h).
STARTING AND OPERATING WARNING! Do not use the locked axle position for normal driving. A locked front axle is intended for off-road driving only. Locking the front axle during on-road driving will reduce the steering ability. This could cause an accident and you may be seriously injured. 333 NOTE: The axle lockers could be torque locked due to side to side loads on the axle.
334 STARTING AND OPERATING (ORV) trails or recreation areas. You should always tread lightly and only use established roads, trails or ORV recreational areas. The National Forest Service, Bureau of Land Management or local Department of Natural Resources are a wealth of information and usually have maps with marked trails. Skid Plates And Underbody Protection Steel skid plates protect the major driveline components of the truck including the fuel tank, transfer case and steering damper.
STARTING AND OPERATING CAUTION! The door sill height is 25 inches. Water may intrude into the interior of the vehicle at greater depths. Simultaneous Brake And Throttle Operation Many off-road driving conditions require the simultaneous use of the brake and throttle (two footed driving). When climbing rocks, logs, or other stepped objects, using light brake pressure with light throttle will keep the vehicle from jerking or lurching.
336 STARTING AND OPERATING WARNING! Always wear your seat belt and firmly tie down cargo. Unsecured cargo can become projectiles in an off-road situation. When To Use Low Range When driving off-road, shift into 4L (Low Range) for additional traction or to improve handling and control on slippery or difficult terrain. Due to the lower gearing, low range will allow the engine to operate in a higher power range. This will allow you to idle over obstacles and down hills, with improved control and less effort.
STARTING AND OPERATING CAUTION! On icy or slippery roads, do not downshift at high engine RPMs or vehicle speeds because engine braking may cause skidding and loss of control. • Mud – Deep mud creates a great deal of suction around the tires and is very difficult to get through. You should use 4L (Low Range) with a gear low enough to maintain your momentum without shifting.
338 STARTING AND OPERATING CAUTION! Reduced tire pressures may cause tire unseating and total loss of air pressure. To reduce the risk of tire unseating, while at a reduced tire pressure, reduce your speed and avoid sharp turns or abrupt maneuvers. Crossing Obstacles (Rocks And Other High Points) While driving off road, you will encounter many types of terrain. These varying types of terrain bring different types of obstacles.
STARTING AND OPERATING Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest with your tires. This will lift your undercarriage over the obstacle. The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse. Always look ahead and make every effort to cross the large rocks with your tires. CAUTION! 339 independently. You need to use caution when crossing large obstacles with steep sides.
340 STARTING AND OPERATING accelerator to avoid spinning the log out from under your tires. Then ease the vehicle off the log using your brakes. CAUTION! CAUTION! Winching or rocking the vehicle off hard objects increases the risk of underbody damage. Do not attempt to cross a log with a greater diameter than the running ground clearance or the vehicle will become high centered.
STARTING AND OPERATING the vehicle if something goes wrong? If everything looks good and you feel confident, then change transmission into a lower gear, shift the transfer case into 4L (Low) and proceed with caution. You should use first gear and 4L (Low Range) for very steep hills. 341 fresh ⬙bite⬙ into the surface and will usually provide enough traction to complete the climb.
342 STARTING AND OPERATING ability to proceed then make sure you are in 4L (Low Range) with the transmission in first gear (manually select first gear on automatic transmissions) and proceed with caution. Allow engine braking to control the descent and apply your brakes if necessary, but do not allow the tires to lock. WARNING! Do not descend a steep grade in NEUTRAL. Use vehicle brakes in conjunction with engine braking.
STARTING AND OPERATING WARNING! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolling the vehicle, which may result in severe injury. Always back carefully straight down a hill in REVERSE. Never back down a hill in NEUTRAL using only the vehicle brakes. Never drive diagonally across a hill, always drive straight up or down.
344 STARTING AND OPERATING CAUTION! Water ingestion into the axles, transmission, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water. Water can cause permanent damage to engine, driveline or other vehicle components and your brakes will be less effective once wet and/or muddy • Before You Cross Any Type Of Water – As you approach any type of water you need to determine if you can cross it safely and responsibly.
STARTING AND OPERATING CAUTION! Muddy waters can reduce the cooling system effectiveness by depositing debris onto the radiator. • Crossing Ditches, Streams, Shallow Rivers Or Other Flowing Water – Flowing water can be extremely dangerous. Never attempt to cross a fast running stream or river even in shallow water. Fast moving water can easily push your vehicle downstream sweeping it out of control.
346 STARTING AND OPERATING form to the ground contour. Different terrain, tires, and vehicles require different tire pressure. Hard surfaces like rock and heavier vehicles require higher pressures than softer surfaces such as sand and lighter vehicles. You will need to experiment to determine what is right for your situation. It is easier and faster to let air out than it is to replace it so, start high and lower it as required.
STARTING AND OPERATING 347 vehicle impingement on the surroundings, then using a • Rock Cycling Your Vehicle – Rock cycling your vetow strap to the vehicle tow hooks would be fast and hicle is one of the easiest, fastest and most commonly easy. If the vehicle is severely hung up or in a situation used methods. This simply involves shifting your where great care needs to be taken during the recovery, vehicle from DRIVE to REVERSE, while applying then nothing can do the job better than a winch.
348 STARTING AND OPERATING CAUTION! Damage can occur when spinning your tires at an excessive high speed. Do not spin your tires faster than an indicated 35 mph (56 km/h). • Using the Tow Hooks With a Tow Strap – Tow straps are a quick and easy way to recover your vehicle from minor situations if you have a secondary vehicle which is not stuck. The tow hooks on your vehicle are designed to take the abusive force generated during vehicle recovery.
STARTING AND OPERATING WARNING! Never use tow straps with end hooks or link two straps with a clevis pin. These heavy metal objects could become projectiles if a strap breaks, which could cause severe injury. Never leave more than two or three feet of slack in the strap. More slack than this greatly increases the risk of injury and vehicle damage. Always keep everyone at least 30 feet away from a strapping or winching situation.
350 STARTING AND OPERATING as you power the winch in. Be careful not to allow • Completely inspect the underbody of your vehicle. slack in the cable as you recover the vehicle. Do not try Check tires, body structure, steering, suspension, and to guide the cable into the drum. If it starts to bunch exhaust system for damage. up on one end, let it. You can re-spool the cable • Check threaded fasteners for looseness, particularly on afterwards.
STARTING AND OPERATING 351 packed material. Packed foreign material can cause a driving and cornering, the limited-slip unit performs simiwheel imbalance and cleaning the wheels will correct larly to a conventional differential. On slippery surfaces, the situation. however, the differential delivers more of the driving effort to the rear wheel having the better traction. WARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.
352 STARTING AND OPERATING Care should be taken to avoid sudden accelerations when both rear wheels are on a slippery surface. This could cause both rear wheels to spin, and allow the vehicle to slide sideways on the crowned surface of a road or in a turn. 2. Slow down if the road has standing water or puddles. DRIVING ON SLIPPERY SURFACES When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface.
STARTING AND OPERATING Flowing/Rising Water WARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flowing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehicle away swiftly. Failure to follow this warning may result in injuries that are serious or fatal to you, your passengers, and others around you.
354 STARTING AND OPERATING CAUTION! (Continued) WARNING! • Driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.e., engine oil, transmission/transaxle, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water. Do not continue to operate the vehicle if any fluid appears contaminated, as this may result in further damage.
STARTING AND OPERATING DRIVING OFF-ROAD Care should be taken when attempting to climb steep hills or driving diagonally across a hill or slope. If natural obstacles force you to travel diagonally up or down a hill, choose a mild angle and keep as little side tilt as possible. Keep the vehicle moving and make turns slowly and cautiously.
356 STARTING AND OPERATING WINCH USAGE (POWER WAGON ONLY) — IF EQUIPPED Things To Know Before Using Your Winch General Winch Information Your vehicle is equipped with an electric vehicle recovery winch. This winch uses the electrical power from the vehicle charging system to power a motor that winds wire rope into the winch drum via planetary gear reduction. By nature, a winch is capable of generating very high forces and should be used with care.
STARTING AND OPERATING Low Voltage Interrupt Your winch is equipped with a device that will interrupt winch function if the vehicle charging system voltage drops to a low level. The winch will not power-in or out for 30 seconds if this device is tripped. If the interrupt is tripped, the vehicle should be operated at high idle for a few minutes to allow the vehicle charging system to recover before continuing to winch.
358 STARTING AND OPERATING Understanding The Features Of Your Winch Winch Components
STARTING AND OPERATING 359 1. Motor: The winch motor is powered by the vehicle 6. Clutch Lever: The clutch lever allows the winch drum charging system and features a thermal protection switch to be disconnected from the winch motor to allow the that automatically stops motor function in the power-in wire rope to be pulled from the winch by hand. direction if the motor gets too hot. 7. Remote Control: The remote control provides the 2.
360 STARTING AND OPERATING Winch Accessories The following accessories are necessary to attach the winch to anchors, change direction of pull, and for safe winching. Gloves: Wire rope, through use, will develop ⬙barbs⬙ which can slice skin. It is extremely important to wear protective gloves while operating the winch or handling the wire rope. Avoid loose fitting clothes or anything that could become entangled in the wire rope and other moving parts.
STARTING AND OPERATING 361 Clevis/D-Shackles: The Operating Your Winch D-Shackle is a safe means of WARNING! connecting the looped ends of cables, straps and snatch • Always use supplied hook strap to hold the hook blocks. The shackle’s pin is when spooling wire rope in or out. threaded to allow easy re• Never use as a hoist. moval. • Never use to move persons. • Never exceed winch or wire rope rated capacity. • Always wear heavy leather gloves when handling the wire rope.
362 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Always keep hands and clothing clear of the wire rope, hook and fairlead opening during operation and when spooling. • Never wrap wire rope back onto itself. Always use a choker chain, wire choker rope or tree trunk protector on the anchor. • Never attach a recovery strap to the winch hook to increase the length of a pull. • Never attempt to tow a vehicle with the recovery strap attached directly to the winch hook.
STARTING AND OPERATING 363 General Information Vehicle Recovery Using the Winch Practice using your winch before you get stuck. Some key CAUTION! points to remember when using your winch are: 1. Always take your time to assess the situation and plan your pull carefully. 2. Always take your time when using a winch. 3. Use the right equipment for the situation. 4. Always wear leather gloves and do not allow the wire rope to slip through your hands when handling the rope. 5.
364 STARTING AND OPERATING CAUTION! (Continued) • Always keep remote control lead clear of the drum, wire rope and rigging. • Inspect for cracks, pinches, frayed wires, or loose connections. Replace if damaged. • Be careful not to pull the Winch Cable Collar through the rollers. Watch and listen to Winch for proper snugness. 1. Inspect the winch, winch mount, and wire rope for damage. Do not use the winch if the mount is loose or rope shows excessive wear or damage. 2. Put on gloves.
STARTING AND OPERATING 365 3. Disengage the clutch to allow free spooling of the 4. Free the winch hook and attach the hook strap. Free winch drum, rotate the clutch lever on the winch to the winch hook from its anchor point. Attach the hook disengage. Freespooling conserves battery power. strap to the hook (if not attached).
366 STARTING AND OPERATING 5. Pull the wire to the anchor point. Pull out enough wire 6. Secure to the anchor point. Once you have established rope to reach your anchor point. Be sure to keep a certain your anchor point, secure the tree-trunk protector or amount of tension on the wire as it can become twisted choker-chain around the object. and over-wrapped when slackened, leading to wire rope damage. To prevent losing the end, hold the hook strap while you work.
STARTING AND OPERATING CAUTION! Always be certain the anchor you select will withstand the load. 367 7. Attach the Clevis/D-shackle and Tree Trunk Protector. Attach the shackle to the two ends of the strap or chain and through the hook loop, being careful not to over tighten (tighten and back-off 1/2 turn). NOTE: How to choose an anchor point: A secure anchor is critical to winching operations. An anchor must be strong enough to hold while winching. Natural anchors include trees, stumps and rocks.
368 STARTING AND OPERATING NOTE: Always ensure the clutch is fully engaged or disengaged. 9. Connect the remote control to the winch control box, located behind the front bumper. Be careful not to let the remote control cord dangle in front of the winch. If you choose to control the winch from inside your vehicle, always pass the remote through a window to avoid pinching the cord in the door. Always disconnect the remote control when not in use. 10. Put wire rope under tension.
STARTING AND OPERATING 369 12. Check wire rope. The wire rope should be neatly wound around the spooling drum. Improper winding can cause damage to the wire rope. 5 11. Check your anchor. Make sure all connections are secured and free of debris before continuing with the winching procedure.
370 STARTING AND OPERATING 13. In certain situations you the vehicle and never near the wire rope or snatch may decide to throw a heavy block. Your situation may have other ⴖno peopleⴖ zones. blanket or similar object over the wire rope. A heavy blanket can absorb energy should the wire rope break. Place it on the wire rope midway between the winch and the anchor point. Do this before the wire rope is put under tension. Do not approach or move the blanket once tension is applied.
STARTING AND OPERATING 371 For additional assistance, the winched vehicle can be NOTE: slowly driven while being pulled by the winch. Continue • Avoid overheating the winch motor. For extended winching, stop at reasonable intervals to allow the pulling until the vehicle is on stable ground. If you are winch motor to cool down. able to drive the vehicle, the winching operation is complete.
372 STARTING AND OPERATING section of the rope and reposition it to the opposite end of the drum, which will free up space for continued winching. 16. Secure vehicle. Once recovery of the vehicle’s is complete, be sure to secure the vehicle’s brakes and put the transmission in PARK. Release tension in the wire rope. 17. Disconnect the wire rope, and disconnect from the anchor. 18. Rewind the wire rope.
STARTING AND OPERATING NOTE: How to spool under no load: Arrange the remote control lead so it cannot be caught in the winch. Arrange the wire rope so it will not kink or tangle when spooled. Be sure any wire rope already on the spooling drum is wound tightly and evenly layered. Tighten and straighten the layer if necessary. Keep the wire rope under light tension and spool the wire rope back and onto the winch drum in even layers. Stop frequently to tighten and straighten the layers as necessary.
374 STARTING AND OPERATING Rigging Techniques How to Change the Pulling Direction Various winching situations will require application of other winching techniques. These could range from too little distance to achieve maximum pull using straight line rigging, simply increasing pulling power, or maintaining a straight-line pulling situation. You will have to assess what technique is correct for your situation. Think ⬙safety⬙ at all times.
STARTING AND OPERATING 375 will enable you to change your pulling direction while Double Line still allowing the wire rope to be at 90° to wind properly onto the spooling drum. Increasing Pulling Power In some cases, you may find yourself needing more pulling power. The use of snatch blocks increases mechanical advantage and that increases your pulling power.
376 STARTING AND OPERATING vehicle’s frame/tow hook and run the wire rope through NOTE: a snatch block. Disengage the clutch and, using the • Increased noise levels at the end of the steering wheel travel are considered normal and do not indicate that snatch block, pull out enough wire to reach your anchor there is a problem with the power steering system. point. Do not attach the hook to the mounting kit.
STARTING AND OPERATING 377 CAUTION! CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur. Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components. Such damage is not covered by the New Vehicle Limited Warranty.
378 STARTING AND OPERATING surfaces. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. PARKING BRAKE The foot-operated parking brake is positioned below the lower left corner of the instrument panel. To release the parking brake, pull the parking brake release handle. NOTE: The “Brake Warning Light” will come on and flash to indicate that the parking brake is applied. You must be sure that the parking brake is fully applied before leaving the vehicle.
STARTING AND OPERATING WARNING! • Always fully apply the parking brake when leaving your vehicle or it may roll and cause damage or injury. Also be certain to leave the transmission in PARK. Failure to do so may allow the vehicle to roll and cause damage or injury. • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition.
380 STARTING AND OPERATING 3500 Dual Rear Wheel Models Only Four-Wheel Anti-Lock Brake System The brake system power assist is provided by a hydroWARNING! boost unit which shares fluid with the power steering system. You may experience some clicking or hissing The Four-Wheel Anti-Lock Brake System contains noises from the hydro-boost system during hard braking sophisticated electronic equipment. It may be susconditions.
STARTING AND OPERATING The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure. The pump motor makes a low humming noise during operation. This is normal. The ABS conducts a low-speed selftest at about 10 mph (16 km/h). If you have your foot lightly on the brake while this test is occurring, you may feel slight pedal movement. The movement can be more apparent on ice and snow. This is normal.
382 STARTING AND OPERATING WARNING! (Continued) • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents. • The capabilities of an ABS-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others.
STARTING AND OPERATING WARNING! • ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
384 STARTING AND OPERATING Brake Assist System (BAS) The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The BAS detects an emergency braking situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes. The system applies optimum pressure to the brakes in emergency braking conditions. This can help reduce braking distances. The BAS complements the ABS.
STARTING AND OPERATING 385 Hill Start Assist (HSA) The HSA system is designed to assist the driver in launching a vehicle on an incline. HSA will maintain the level of brake pressure the driver inputs for a short duration once the driver takes his foot off of the brake pedal. If the driver does not apply the throttle during this short duration, the system will release brake pressure and the vehicle will roll down the incline.
386 STARTING AND OPERATING The system will only work if the intended direction of the vehicle and vehicle gear match. For example, if the intended direction is forward up a hill and the vehicle is in DRIVE and the activation criteria are met, HSA will activate. The system will work in REVERSE and all forward gears, and will not activate if the vehicle is placed in NEUTRAL.
STARTING AND OPERATING WARNING! (Continued) • HSA is not a parking brake. If you stop the vehicle on a hill without putting the transmission in PARK or using the parking brake, it will roll down the incline and could cause a collision with another vehicle or object. Always remember to use the parking brake while parking on a hill and that the driver is responsible for braking the vehicle. 387 3. With the engine running and the brake applied, rotate the steering wheel 180° counterclockwise from center. 4.
388 STARTING AND OPERATING EVIC Equipped Vehicles HSA is a Customer Programmable Feature on a EVIC equipped vehicle. If you wish to turn off the HSA feature, refer to “Customer Programmable Features/Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. Electronic Stability Program (ESP) The ESP system enhances directional control and stability of the vehicle under various driving conditions.
STARTING AND OPERATING • Oversteer - when the vehicle is turning more than appropriate for the steering wheel position. • Understeer - when the vehicle is turning less than appropriate for the steering wheel position. 389 WARNING! • ESP cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.
390 STARTING AND OPERATING (2WD/4WD AUTO/4WD LOCK/4WD LOW/ NEUTRAL) transfer case. If you have a four-wheel drive vehicle, and want to determine which transfer case is on your vehicle and how to operate it, refer to “Four-Wheel Drive Operation” in “Starting and Operating” for further information. driving situations. ESP should only be turned to “Partial Off” or “ESP Off” for specific reasons as noted below. ESP Partial Off This mode is entered by momentarily pressing the ESP OFF switch.
STARTING AND OPERATING requiring ESP to be switched to the “Partial Off” mode is overcome, turn ESP back on by momentarily pressing the ESP OFF switch. This may be done while the vehicle is in motion. WARNING! In the “Partial Off” mode, the engine torque reduction and stability features are desensitized. Therefore, the enhanced vehicle stability offered by ESP is unavailable. All Four-Wheel Drive Vehicles in 4WD AUTO and 4WD LOCK Modes Can Also Choose the Following ESP Operating Mode.
392 STARTING AND OPERATING off at low vehicle speeds so that it will not interfere with off-road driving but ESP function returns to provide the stability feature at speeds above 40 mph (64 km/h). The “ESP/TCS Indicator Light” will always be illuminated when ESP is off. To turn ESP on again, momentarily press the ESP OFF switch. This will restore the normal “ESP On” mode of operation. WARNING! With the ESP switched off, the enhanced vehicle stability offered by ESP is unavailable.
STARTING AND OPERATING this light remains on after several ignition cycles and the vehicle has been driven several miles/kilometers at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected. NOTE: • The “ESP Indicator Light” and the “ESP/BAS Warning Light” will come on momentarily each time the ignition switch is turned ON. • Each time the ignition is turned ON, the ESP will be ON even if it was turned off previously.
394 STARTING AND OPERATING TSC is only active in the default “ESP On” mode. TSC can TIRE SAFETY INFORMATION be disabled by pressing the ESP OFF switch and entering Tire Markings “ESP Partial Off” mode. It is not active in the “ESP Partial Off” or “ESP Off” modes. Refer to the ESP portion of this section for an explanation of the different ESP operating modes.
STARTING AND OPERATING NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa• tion. Example: P215/65R15 95H. 395 tires is the same as for P-Metric tires except for the letters “LT” that are molded into the sidewall preceding the size designation. Example: LT235/85R16. Temporary spare tires are high-pressure compact spares designed for temporary emergency use only.
396 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
STARTING AND OPERATING 397 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
398 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
STARTING AND OPERATING 399 Tire Terminology and Definitions Term B-Pillar Cold Tire Pressure Maximum Inflation Pressure Recommended Inflation Pressure Tire Placard Definition The vehicle B-Pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.
400 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires.
STARTING AND OPERATING NOTE: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded. For further information on GAWRs, vehicle loading, and trailer towing, refer to “Vehicle Loading” in this section. To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard.
402 STARTING AND OPERATING 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load carry capacity of your vehicle.
STARTING AND OPERATING 403 5
404 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement.
406 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the Winter.
STARTING AND OPERATING 407 Tire Pressures for High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle important. Increased tire pressure and reduced vehicle poorly.
408 STARTING AND OPERATING original equipped tire on the front or rear axle of your vehicle, but it is not. Installation of this limited-use spare tire affects vehicle handling. Since it is not the same tire, replace (or repair) the original tire and reinstall on the vehicle at the first opportunity. Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck.
STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. 409 These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced.
410 STARTING AND OPERATING wear and correct cold tire inflation pressure. The manufacturer strongly recommends that you use tires equivalent to the originals in size, quality and performance Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to when replacement is needed. (Refer to the paragraph on follow this warning can result in sudden tire failure. “Tread Wear Indicators”).
STARTING AND OPERATING 411 WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
412 STARTING AND OPERATING TIRE CHAINS Use “Class S” chains, or other traction aids that meet SAE Type “S” specifications. Use “Class U” chains on 2500/3500 model trucks, or other traction aids that meet SAE Type “U” specifications. NOTE: Chains must be the proper size for the vehicle as recommended by the chain manufacturer.
STARTING AND OPERATING CAUTION! (Continued) • Observe the tire chain manufacturer’s instructions on method of installation, operating speed, and conditions for usage. Always use the lower suggested operating speed of the chain manufacturer if different than the speed recommended by the manufacturer. These cautions apply to all chain traction devices, including link and cable (radial) chains.
414 STARTING AND OPERATING CAUTION! Do not use tire chains on 4x4 model trucks equipped with P265/70R17, LT275/70R17, P275/60R20, tires. There may not be adequate clearance for the chains and you are risking structural or body damage to your vehicle. Do not use tire chains on the 4X2 front wheels of 2500/3500 SRW (Single Rear Wheels) equipped with LT245/70R17, LT265/70R17 LT235/ 80R17 tires, or 4X4 front wheels equipped with LT265/70R17E.
STARTING AND OPERATING 415 tires. Rotation will increase tread life, help to maintain mud, snow and wet traction levels and contribute to a smooth, quiet ride. Refer to “Maintenance Schedule” for the proper maintenance intervals. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed. The suggested rotation method is the “forward cross” shown in the following diagram.
416 STARTING AND OPERATING Dual Rear Wheels CAUTION! 3500 Dual Rear Tires have only one approved direction of rotation. This is to accommodate the asymmetrical design (tread pattern) of the On/Off-Road tire and the use of Outline White Letter (OWL) tires. Tire Rotation The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires. The straight edge should touch all the tires.
STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM (TPMS) The Tire Pressure Monitoring System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold tire inflation placard pressure. The placard pressure is defined on the Tire and Loading Information label. The Tire and Loading Information label is located on the drivers side B-pillar. The tire pressure will vary with temperature by approximately 1 psi (6.9 kPa) for every 12°F (6.5°C).
418 STARTING AND OPERATING have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) to receive this information. As an example, assume your vehicle has a recommended cold tire inflation placard pressure (parked for more than 3 hours) of 35 psi (241 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 30 psi (207 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressure to approximately 26 psi (179 kPa).
STARTING AND OPERATING 419 NOTE: • Seasonal temperature changes will affect tire pressure, • The TPMS is not intended to replace normal tire care and the TPMS will monitor the actual tire pressure in and maintenance, nor to provide warning of a tire the tire. failure or condition. Tire Pressure Monitor System Components • The TPMS should not be used as a tire pressure gauge The TPMS uses wireless technology with wheel rim while adjusting your tire pressure.
420 STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Lamp will illuminate in the instrument cluster, and an audible chime will be activated when one or more of the four active road tire pressures are low. Should this occur, you should stop as soon as possible, check the inflation pressure of each tire on your vehicle and inflate each tire to the vehicle’s recommended cold placard pressure value.
STARTING AND OPERATING 421 1. This spare tire does not have a tire pressure monitor- 4. For each subsequent ignition switch cycle, a chime will ing sensor. Therefore, the TPMS will not monitor the tire sound and the “TPM Telltale Light” will flash on and off pressure in the spare tire. for 75 seconds and then remain on solid. 2.
422 STARTING AND OPERATING Tire Pressure Monitor System (TPMS) Tire Light Load Inflation Switch Description (2500 Models) – If Equipped WARNING! Never operate your vehicle with the TPMS and tire pressures set to the Light Load Inflation Pressure settings if carrying more than two occupants (150 lbs [68 kg] each) plus 200 pounds (91 kg) of cargo. The vehicle “Light Load Definition” is found in the Supplemental Tire Pressure Information Label which is located on the rear face of the driver door.
STARTING AND OPERATING 423 Tire Light Load Inflation Switch Operation – If Equipped • This vehicle may have different recommended tire pressure values between the front and rear tires as shown in both the Tire Loading Information Label and the Supplemental Tire Pressure Information Label. It is also equipped to be driven with tire pressures appropriate to either a Light Load condition or the vehicle Max Load condition.
424 STARTING AND OPERATING • The tire light load inflation switch will allow the driver to change between the max load inflation pressure (cold) low pressure warning threshold and the light load inflation pressure (cold) low pressure warning threshold depending on the vehicle’s load condition. Refer to the “Supplemental Tire Pressure Information” label for the vehicle’s Light Load inflation pressures and “Tire and Loading Information” label for the vehicle’s Max Load inflation pressures.
STARTING AND OPERATING 425 Tire Pressure Information label. The Supplemental Tire the rear face of the driver door. Using an accurate tire Pressure Information label is located on the rear face of pressure gauge, re-check the tire pressures for the light the driver door. Use an accurate tire gauge to check the load inflation pressure (cold) value. tire pressures when lowering all four tire pressures.
426 STARTING AND OPERATING the max load inflation pressure (cold) values to switch the TPMS system to the max load inflation pressure (cold) low pressure warning threshold. If after pressing the tire light load inflation switch, and tire pressures are below the max load inflation pressure (cold) low pressure warning thresholds, the TPMS low pressure warning telltale light (located in the instrument cluster) will turn ON and a chime will sound.
STARTING AND OPERATING FUEL REQUIREMENTS 3.7L and 4.7L Engine All engines (except 5.7L engines) are designed to meet all emissions regulations and provide excellent fuel economy and performance when using high quality unleaded “regular” gasoline having an octane rating of 87. The use of premium gasoline is not recommended, as it will not provide any benefit over regular gasoline in these engines. 5.7L Engine The 5.
428 STARTING AND OPERATING Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasolines contain oxygenates and are specifically blended to reduce vehicle emissions and improve air quality. CAUTION! Do not use gasoline containing Methanol or E85 Ethanol. Use of these blends may result in starting and drivability problems and may damage critical fuel system components.
STARTING AND OPERATING 429 • OBD II “Malfunction Indicator Light” on blended with MMT provides no performance advantage beyond gasoline of the same octane number without • poor engine performance MMT. Gasoline blended with MMT reduces spark plug life and reduces emissions system performance in some • poor cold start and cold drivability vehicles. The manufacturer recommends that gasoline • increased risk for fuel system component corrosion without MMT be used in your vehicle.
430 STARTING AND OPERATING Fuel System Cautions CAUTION! (Continued) CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance and damage the emission control system. • An out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat.
STARTING AND OPERATING Carbon Monoxide Warnings 431 WARNING! (Continued) WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
432 STARTING AND OPERATING FLEXIBLE FUEL (4.7L ENGINE ONLY) — IF EQUIPPED E85 General Information The information in this section is for Flexible Fuel Vehicles (FFV) only. These vehicles can be identified by the unique fuel filler door label that states Ethanol (E85) or Unleaded Gasoline Only. This section only covers those subjects that are unique to these vehicles.
STARTING AND OPERATING 433 WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use E85 as a cleaning agent and never use it near an open flame. E85 Badge Fuel Requirements If your vehicle is E85 compatible, it will operate on unleaded gasoline with an octane rating of 87, or E85 fuel, or any mixture of these two fuels.
434 STARTING AND OPERATING • you drive the vehicle immediately after refueling for at Selection Of Engine Oil For Flexible Fuel Vehicles least 5 miles (8 km) (E85) and Gasoline Vehicles FFV vehicles operated on E85 require specially formuObserving these precautions will avoid possible hard lated engine oils. These special requirements are included starting and/or significant deterioration in driveability in MOPAR威 engine oils, and in equivalent oils meeting during warm up. Chrysler Specification MS-6395.
STARTING AND OPERATING NOTE: Use of the engine block heater (if equipped) is beneficial for E85 startability when the ambient temperature is less than 32°F (0°C). 435 CAUTION! Replacing fuel system components with non-ethanol compatible components can damage your vehicle. Cruising Range Because E85 fuel contains less energy per gallon/liter Maintenance than gasoline, you will experience an increase in fuel If you operate the vehicle using E85 fuel, follow the consumption.
436 STARTING AND OPERATING NOTE: When removing the fuel filler cap, lay the cap ADDING FUEL The fuel filler cap (gas cap) is located behind the fuel tether in the hook, located on the fuel filler door. filler door, on the left side of the vehicle. Open the fuel CAUTION! door and remove the fuel cap by turning it counterclockwise. • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap).
STARTING AND OPERATING WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel to the vehicle when the engine is running. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. 437 • When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
438 STARTING AND OPERATING Payload The payload of a vehicle is defined as the allowable load Certification Label weight a truck can carry, including the weight of the As required by National Highway Traffic Safety Admindriver, all passengers, options and cargo. istration regulations, your vehicle has a certification label Gross Axle Weight Rating (GAWR) affixed to the driver’s side door or pillar.
STARTING AND OPERATING 439 The entire vehicle should first be weighed on a commerRim Size This is the rim size that is appropriate for the tire size cial scale to insure that the GVWR has not been exceeded. The weight on the front and rear of the vehicle should listed. then be determined separately to be sure that the load is Inflation Pressure properly distributed over the front and rear axle.
440 STARTING AND OPERATING CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also overloading can shorten the life of your vehicle.
STARTING AND OPERATING 441 Gross Combination Weight Rating (GCWR) Tongue Weight (TW) The GCWR is the total permissible weight of your vehicle The tongue weight is the downward force exerted on the and trailer when weighed in combination. hitch ball by the trailer. In most cases it should not be less than 10% or more than 15% of the trailer load. You must NOTE: The GCWR rating includes a 150 lbs (68 kg) consider this as part of the load on your vehicle. allowance for the presence of a driver.
442 STARTING AND OPERATING hitches are the most popular on the market today and they’re commonly used to tow small- and medium-sized trailers. Weight-Distributing Hitch A weight-distributing system works by applying leverage through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s).
STARTING AND OPERATING 443 5 EXAMPLE — Without Weight-Distributing Hitch (Incorrect) EXAMPLE — With Weight-Distributing Hitch (Correct)
444 STARTING AND OPERATING Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck. The coupling arm connects to the hitch mounted over the rear axle in the truck bed. EXAMPLE — Improper Adjustment of WeightDistributing Hitch (Incorrect) Fifth-Wheel Hitch The fifth-wheel hitch is a special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed.
STARTING AND OPERATING 445 Weight Ratings)” for the website address that contains All trailer hitches should be professionally installed on the necessary information for your specific drivetrain. your vehicle. Trailer Hitch Classification Definitions Class Max.
446 STARTING AND OPERATING Never exceed the maximum tongue weight stamped on • The weight of any other type of cargo or equipment your bumper or trailer hitch. put in or on your vehicle • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.
STARTING AND OPERATING Towing Requirements To promote proper break-in of your new vehicle drivetrain components the following guidelines are recommended: CAUTION! • Do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven. The engine, axle or other parts could be damaged. • Then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle.
448 STARTING AND OPERATING WARNING! (Continued) • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. 1. GVWR 2. GTW 3. GAWR 4.
STARTING AND OPERATING • Check for signs of tire wear or visible tire damage before towing a trailer. Refer to “Tires – General Information” in “Starting and Operating” for the proper inspection procedure. • When replacing tires, refer to “Tires – General Information” in “Starting and Operating” for proper tire replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s GVWR and GAWR limits.
450 STARTING AND OPERATING WARNING! • Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. • Towing any trailer will increase your stopping distance. When towing you should allow for additional space between your vehicle and the vehicle in front of you. Failure to do so could result in an accident.
STARTING AND OPERATING 451 This display may also be used to display diagnostic The trailer and the vehicle’s brake lamps will come on when either vehicle braking or manual trailer brakes are information, if needed. applied. • SC — Short Circuit to Ground Trailer Brake Status Indicator Light • Sb — Short to Battery This light indicates the trailer electrical connection status.
452 STARTING AND OPERATING GAIN setting can be increased to a maximum of 10 or 3. When a trailer with electric brakes is plugged in, the decreased to a minimum of 0 (no trailer braking). GAIN setting will illuminate. GAIN The GAIN setting is used to set the trailer brake control for the specific towing condition and should be changed as towing conditions change. Changes to towing conditions include trailer load, vehicle load, road conditions and weather. Adjusting GAIN 4.
STARTING AND OPERATING EVIC Display Messages The trailer brake control interacts with the Electronic Vehicle Information Center (EVIC). Display messages, along with a single chime, will be displayed when a malfunction is determined in the trailer connection, trailer brake control, or on the trailer. Refer to “Electronic Vehicle Information Center” in “Understanding Your Instrument Panel” for further information.
454 STARTING AND OPERATING The Trailer Tow Package will include a four and sevenpin wiring harness. Use a factory approved trailer harness and connector. NOTE: Do not cut or splice wiring into the vehicle’s wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations.
STARTING AND OPERATING 455 WARNING! Any work done to the vehicle’s electrical system or wiring should be performed by a qualified automotive technician. If done improperly it may cause damage to the electrical system wiring and could result in serious or fatal injury. Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer up in an area away from heavy traffic.
456 STARTING AND OPERATING NOTE: Using “TOW/HAUL” mode or a lower gear Electronic Speed Control – If Equipped range while operating the vehicle under heavy operating − Do not use in hilly terrain or with heavy loads. conditions will improve performance and extend transmission life by reducing excessive shifting and heat build − When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until up. This action will also provide better engine braking.
STARTING AND OPERATING − Air Conditioning Turn off temporarily. 457 CAUTION! Using this vehicle for snowplow applications can cause damage to the vehicle. SNOWPLOW 1500 Models Only NOTE: Do not use this model vehicle for snowplow applications. WARNING! Snowplows and other aftermarket equipment should not be added to the front end of your vehicle. The airbag crash sensors may be affected by the change in the front end structure.
458 STARTING AND OPERATING Dodge Body Builders Guide. See your authorized dealer, Before Plowing installer or snowplow manufacturer for this information. • Check the hydraulic system for leaks and proper fluid There are unique electrical systems that must be conlevel. nected to properly assure operator safety and prevent • Check the mounting bolts and nuts for proper tightoverloading vehicle systems. ness.
STARTING AND OPERATING 2. The total GVWR or the Front GAWR or the Rear GAWR should never be exceeded. 459 if necessary at the beginning and end of the snowplow season. This will help prevent uneven tire wear. 3. Cargo capacity will be reduced by the addition of The blade should be lowered whenever the vehicle is options or passengers, etc. parked.
460 STARTING AND OPERATING Operating Tips Under ideal snow plowing conditions, 20 mph (32 km/h) should be maximum operating speed. The operator should be familiar with the area and surface to be cleaned. Reduce speed and use extreme caution when plowing unfamiliar areas or under poor visibility. NOTE: During snowplow usage on vehicles equipped with outside temperature display, the display may show higher temperatures than the outside ambient temperature.
STARTING AND OPERATING 461 • Do not shift the transmission unless the engine has Recreational Towing – Four-Wheel Drive Models returned to idle and wheels have stopped. Make a CAUTION! practice of stepping on the brake pedal before shifting the transmission. Failure to follow these requirements can cause severe damage to the transmission and/or transfer case. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
462 STARTING AND OPERATING Recreational Towing Procedure (Manual Shift Transfer Case) – If Equipped Use the following procedure to prepare your vehicle for recreational towing: CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in NEUTRAL before recreational towing to prevent damage to internal parts.
STARTING AND OPERATING 463 9. Repeat steps 7 and 8 with the transmission in DRIVE. Returning to Normal Operation – Manual Shift Transfer Case 10. Turn OFF the engine and place the ignition switch in Use the following procedure to prepare your vehicle for the OFF position. normal usage: 11. Shift the transmission into PARK. 1. Bring the vehicle to a complete stop. 12. Apply the parking brake. 2. Apply the parking brake. 13. Attach the vehicle to the tow vehicle with the tow bar. 3. Shut OFF the engine. 14.
464 STARTING AND OPERATING WARNING! CAUTION! You or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake. The transfer case NEUTRAL position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move, even if the transmission is in PARK. The parking brake should always be applied when the driver is not in the vehicle.
STARTING AND OPERATING Recreational Towing Procedure (Electronic Shift Transfer Case) – If Equipped Use the following procedure to prepare your vehicle for recreational towing: 465 CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in NEUTRAL before recreational towing to prevent damage to internal parts.
466 STARTING AND OPERATING • Steps 1 through 5 are requirements that must be met prior to pressing the NEUTRAL button, and must 9. Shift the transmission into REVERSE. continue to be met until the four seconds elapses and 10. Release the brake pedal for five seconds and ensure the shift has been completed. If any of these requirethat there is no vehicle movement. ments (with the exception of 3 - Key ON) are not met prior to pressing the NEUTRAL button or are no 11.
STARTING AND OPERATING CAUTION! Damage to the transmission may occur if the transmission is shifted into PARK with the transfer case in NEUTRAL and the engine running. With the transfer case in NEUTRAL, ensure that the engine is OFF prior to shifting the transmission into PARK. 467 5. Shift the transmission into NEUTRAL. 6. Press the transfer case switch NEUTRAL button for one second. 7. After the NEUTRAL indicator light turns off, release the NEUTRAL button. 8.
468 STARTING AND OPERATING of the mode position indicator lights will flash continuously until all requirements are met or until the NEUTRAL button is released. • The ignition switch must be in the ON position for a transfer case shift to take place and for the position indicator lights to be operable. If the ignition switch is not in the ON position, the shift will not take place and no position indicator lights will be on or flashing.
STARTING AND OPERATING CAUTION! • Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and fluid loss will damage internal parts. 469 EQUIPMENT IDENTIFICATION PLATE The equipment Identification Plate is located on the hood inner surface.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . 472 䡵 Hoisting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 491 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 472 䡵 Jump-Starting Procedures . . . . . . . . . . . . . . . . 491 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . 473 ▫ Preparations For Jump-Start . . . . . . . . . . . . . 492 ▫ Removing The Spare Tire . . . . . . . . . . . . . . .
472 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER JACKING AND TIRE CHANGING The Hazard Warning flasher switch is located on the WARNING! upper switch bank just below the radio. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off the Hazard Warning flasher.
WHAT TO DO IN EMERGENCIES 473 Jack Location The jack and jack tools are stored under the front passenger seat. Removal To access the jack and jack tools you must remove the plastic access cover, located on the side of the seat. To remove the cover, pull the front part of the cover (closest to the front of the seat) toward you to release a locking tab. Once the front of the cover is loose, slide the cover toward the front of the seat until it is free from the seat frame.
474 WHAT TO DO IN EMERGENCIES Remove the jack and tools by removing the wing bolt and sliding the assembly from under the seat.
WHAT TO DO IN EMERGENCIES 475 WARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid acceleration or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury. Reinstalling The Jack And Tools (1500 Series) 1. Lower the jack all the way down by turning the jack turn-screw until the jack is snug. 2.
476 WHAT TO DO IN EMERGENCIES 3. Fold the flap and roll the jack tool kit into a cylindrical package (in direction of arrows) and tie to the jack using the tie straps.
WHAT TO DO IN EMERGENCIES 477 6 Jack and Tools Tied 4. Place the jack and tools in the storage position holding the jack by the jack turn-screw, slip the jack and tools under the seat so that the bottom slot engages into the fastener on the floor, and then secure to the floor pan using the wing bolt. Reinstall the plastic cover.
478 WHAT TO DO IN EMERGENCIES Removing The Spare Tire Remove the spare tire before attempting to jack up the truck. Attach the wheel wrench to the jack extension tube. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube. Rotate the wheel wrench handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle.
WHAT TO DO IN EMERGENCIES 479 NOTE: The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. Preparations 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. WARNING! Removing the Spare Tire 1 — Wheel Wrench 2 — Spare Tire Do not attempt to change a tire on the side of the vehicle close to moving traffic.
480 WHAT TO DO IN EMERGENCIES 4. Turn the ignition OFF. 5. Turn on the Hazard Warning flasher. 6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked.
WHAT TO DO IN EMERGENCIES 481 WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway, be extremely careful of motor traffic. • To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground. • Turn on the Hazard Warning flasher.
482 WHAT TO DO IN EMERGENCIES • 1500 Series Trucks When changing a front wheel, place the scissors jack under the rear portion of the lower control arm as shown below. 4X4 Jacking Location Operate the jack using the jack drive tube and the wheel wrench. The tube extension may be used but is not required.
WHAT TO DO IN EMERGENCIES 483 For 4x2 and 4x4 trucks, when changing a rear wheel, Connect the jack tube extension and wheel wrench. assemble the jack drive tube to the jack and connect the CAUTION! drive tube to the extension tube. Place the jack under the axle between the wheel and the shock bracket with the Before raising the wheel off the ground, make sure drive tubes extending to the rear. that the jack will not damage surrounding truck parts and adjust the jack position as required.
484 WHAT TO DO IN EMERGENCIES • 2500/3500 Series Trucks For 2500/3500 4x2 series trucks, when changing a front wheel, place the bottle jack under the frame rail behind the wheel. Locate the jack as far forward as possible on the straight part of the frame. 4x2 Jacking Location Operate the jack using the jack drive tube and the wheel wrench. The tube extension, may be used, but is not required.
WHAT TO DO IN EMERGENCIES 485 6 4x4 Jacking Location Rear Jacking Location (All) For 4x2 and 4x4 trucks, when changing a rear wheel, Connect the jack tube extension and wheel wrench. assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle between the spring and the shock absorber with the drive tubes extending to the rear.
486 WHAT TO DO IN EMERGENCIES 5. Remove the wheel nuts and pull the wheel off. On single rear-wheel (SRW) trucks, install the spare wheel Before raising the wheel off the ground, make sure and wheel nuts with the cone shaped end of the wheel that the jack will not damage surrounding truck parts nuts toward the wheel. On 3500 dual rear-wheel models (DRW) the wheel nuts are a two-piece assembly with a and adjust the jack position as required. flat face. Lightly tighten the wheel nuts.
WHAT TO DO IN EMERGENCIES WARNING! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Always stow the jack parts and the extra tire and wheel in the places provided. 487 Hub Caps/Wheel Covers — If Equipped The hub caps must be removed before raising the vehicle off the ground. For 2500/3500 single rear-wheel (SRW) models, use the blade on the end of the lug wrench to pry the hub cap off.
488 WHAT TO DO IN EMERGENCIES Wheel Nuts All wheel nuts should be tightened occasionally to elimi• Use a back-and-forth motion to remove the hub cap. nate the possibility of wheel studs being sheared or the bolt Do not use a twisting motion when removing the holes in the wheels becoming elongated. This is especially important during the first few hundred miles/kilometers hub cap, damage to the hub cap finish may occur.
WHAT TO DO IN EMERGENCIES 8-Stud — Dual Rear Wheels Dual wheels are flat-mounted and center-piloted. The lug nuts are a two-piece assembly. When the tires are being rotated or replaced, clean these lug nuts and add two drops of oil at the interface between the hex and the washer. 489 Slots in the wheels will assist in properly orienting the inner and outer wheels. Align these slots when assembling the wheels for best access to the tire valve on the inner wheel.
490 WHAT TO DO IN EMERGENCIES These dual rear wheels should be tightened as follows: second time to verify that specific torque has been achieved. Retighten to specifications at 100 miles (160 km) and after 500 miles (800 km). It is recommended that wheel stud nuts be kept torqued to specifications at all times. Torque wheel stud nuts to specifications at each lubrication interval. To Stow The Flat Or Spare Tightening Pattern 1. Tighten the wheel nuts in the numbered sequence to a snug fit. 2.
WHAT TO DO IN EMERGENCIES WARNING! A loose tire thrown forward in a collision or hard stop could injure the occupants in the vehicle. Have the deflated (flat) tire repaired or replaced immediately. 491 HOISTING A conventional floor jack may be used at the jacking locations. Refer to the graphics that show jacking locations. However, a floor jack or frame hoist must never be used on any other parts or the underbody. CAUTION! Turn the wheel so that the valve stem is down.
492 WHAT TO DO IN EMERGENCIES NOTE: When using a portable battery booster pack Preparations for Jump-Start follow the manufacturer’s operating instructions and The battery in your vehicle is located in the front of the engine compartment, behind the left headlight assembly. precautions. CAUTION! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.
WHAT TO DO IN EMERGENCIES WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
494 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 5.
WHAT TO DO IN EMERGENCIES 495 8. Disconnect the opposite end of the positive (+) jumper FREEING A STUCK VEHICLE If the vehicle becomes stuck in snow, sand or mud, it can cable from the positive (+) post of the booster battery. often be moved by a rocking motion. Move the shift lever 9. Disconnect the positive (+) end of the jumper cable rhythmically between DRIVE and REVERSE while apfrom the positive (+) post of the discharged vehicle. plying slight pressure to the accelerator.
496 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! • When “rocking” a stuck vehicle by moving between 1st and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result. • Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h). Fast spinning tires can be dangerous.
WHAT TO DO IN EMERGENCIES WARNING! • Chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. • Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. CAUTION! Tow hooks are for emergency use only to rescue a vehicle stranded off-road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle.
498 WHAT TO DO IN EMERGENCIES CAUTION! CAUTION! Failure to follow these towing methods could result in damage to the transfer case. Such damage is not covered by the New Vehicle Limited Warranty. Towing faster than 30 mph (50 km/h) or for more than 15 miles (25 km) can cause severe damage to the transmission. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 3.7L . . . . . . . . . . . . . 502 䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . 508 䡵 Engine Compartment — 4.7L . . . . . . . . . . . . . 503 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 509 䡵 Engine Compartment — 5.7L . . . . . . . . . . . . . 504 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 511 䡵 Onboard Diagnostic System (OBD II) . . . . . . . 505 ▫ Engine Air Cleaner Filter . . . . . . . . .
500 MAINTAINING YOUR VEHICLE ▫ Windshield Wiper Blades . . . . . . . . . . . . . . . 516 䡵 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . 542 ▫ Adding Washer Fluid . . . . . . . . . . . . . . . . . 516 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 543 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . 517 ▫ Dual Or Quad Headlamp/Front Park And Turn Signal — If Equipped . . . . . . . . . . . . . 543 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 䡵 Fluid Capacities 501 . . . . . . . . . . . . . . . . . . . . . . 552 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 554 䡵 Fluids, Lubricants And Genuine Parts . . . . . . . 554 ▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . .
502 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 3.
MAINTAINING YOUR VEHICLE 503 ENGINE COMPARTMENT — 4.
504 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 5.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) Your vehicle is equipped with a sophisticated onboard diagnostic system called OBDII. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
506 MAINTAINING YOUR VEHICLE will appear the next time the vehicle is started. This serviced, recently had a dead battery or a battery replacemight indicate a damaged cap. If the problem is detected ment. If the OBD II system should be determined not twice in a row, the system will turn on the MIL. Resolving ready for the I/M test, your vehicle may fail the test. the problem will turn the MIL light off.
MAINTAINING YOUR VEHICLE 507 4. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced a. The MIL will flash for about 10 seconds and then before going to the I/M station. The I/M station can fail return to being fully illuminated until you turn OFF your vehicle because the MIL is on with the engine the ignition or start the engine.
508 MAINTAINING YOUR VEHICLE your vehicle. Refer to these manuals before attempting MAINTENANCE PROCEDURES The pages that follow contain the required maintenance any procedure yourself. services determined by the engineers who designed your NOTE: Intentional tampering with emissions control vehicle. systems may void your warranty and could result in civil Besides those maintenance items specified in the fixed penalties being assessed against you.
MAINTAINING YOUR VEHICLE CAUTION! (Continued) • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or air conditioning. Such damage is not covered by the New Vehicle Limited Warranty.
510 MAINTAINING YOUR VEHICLE NOTE: Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, whichever occurs first. CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE 511 Lubricants which do not have both the engine oil certi- Disposing of Used Engine Oil and Oil Filters fication mark and the correct SAE viscosity grade num- Care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, ber should not be used. indiscriminately discarded, can present a problem to the NOTE: For 2500/3500 trucks with a 5.7L engine operenvironment.
512 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter used to assure most efficient service. MOPAR威 engine air Refer to “Maintenance Schedule” for further information. cleaner filters are a high quality filter and are recommended. WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance.
MAINTAINING YOUR VEHICLE 513 WARNING! (Continued) CAUTION! • Battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a booster battery or any other booster source with an output greater than 12 volts. Do not allow cable clamps to touch each other. • Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling.
514 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. CAUTION! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air conditioning components.
MAINTAINING YOUR VEHICLE 515 tailgate, sliding doors and hood hinges, should be lubricated periodically with a lithium based grease, such as MOPAR威 Spray White Lube or equivalent, to assure quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit. After lubricating, excess oil and grease should be removed.
516 MAINTAINING YOUR VEHICLE Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield.
MAINTAINING YOUR VEHICLE 517 Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the Commercially available windshield washer solvents vehicle or when the underside or rear of the vehicle is are flammable. They could ignite and burn you. Care damaged, have a competent mechanic inspect the commust be exercised when filling or working around plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
518 MAINTAINING YOUR VEHICLE WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Safety Tips/Exhaust Gas” in “Things To Know Before Starting Your Vehicle” for further information. CAUTION! The catalytic converter requires the use of unleaded fuel only.
MAINTAINING YOUR VEHICLE 519 NOTE: Intentional tampering with emissions control To minimize the possibility of catalyst damage: systems can result in civil penalties being assessed • Do not shut off the engine or interrupt the ignition against you. when the transmission is in gear and the vehicle is in motion. WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system.
520 MAINTAINING YOUR VEHICLE Cooling System WARNING! You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot. Check the coolant recovery bottle tubing for brittle rubber, cracking, tears, cuts and tightness of the connection at the bottle and radiator. Inspect the entire system for leaks.
MAINTAINING YOUR VEHICLE Refer to “Maintenance Schedule” for further information. Selection Of Coolant Use only the manufacturer’s recommended engine coolant (antifreeze). Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. CAUTION! • Mixing of engine coolant (antifreeze) other than specified HOAT engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.
522 MAINTAINING YOUR VEHICLE Please review these recommendations for using Hybrid Please note that it is the owner’s responsibility to mainOrganic Additive Technology (HOAT) engine coolant tain the proper level of protection against freezing according to the temperatures occurring in the area where (antifreeze). the vehicle is operated.
MAINTAINING YOUR VEHICLE WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
524 MAINTAINING YOUR VEHICLE When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. coolant (antifreeze) needs to be added, contents of coolant recovery bottle must also be protected against freezing.
MAINTAINING YOUR VEHICLE • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emissions. Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Refer to “Maintenance Schedule” for further information.
526 MAINTAINING YOUR VEHICLE WARNING! WARNING! (Continued) • Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid for your vehicle is also labeled on the original factory installed hydraulic master cylinder reservoir.
MAINTAINING YOUR VEHICLE WARNING! (Continued) • Do not allow petroleum based fluid to contaminate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in an accident. Rear Axle And 4x4 Front Driving Axle Fluid Level For normal service, periodic fluid level checks are not required. When the vehicle is serviced for other reasons the exterior surfaces of the axle assembly should be inspected.
528 MAINTAINING YOUR VEHICLE Limited-Slip Differentials This vehicle requires that 4 oz. (118 ml) MOPAR威 Limited Slip Additive or equivalent be added to the gear lubricant. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. The MOPAR威 Limited Slip Additive or equivalent should be added to the gear lubricant whenever a fluid change is made. Fluid Level Check This fluid level can be checked by removing the filler plug.
MAINTAINING YOUR VEHICLE CAUTION! • Do not use chemical flushes in your transmission as the chemicals can damage your transmission components. Such damage is not covered by the New Vehicle Limited Warranty. • Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter changes.
530 MAINTAINING YOUR VEHICLE NOTE: If it is necessary to check the transmission below the operating temperature, the fluid level should be 3. Fully apply the parking brake and press the brake between the two “COLD” (lower) holes on the dipstick pedal. with the fluid at approximately 70°F (21°C) (room tem4. Place the shift lever momentarily into each gear posi- perature). If the fluid level is correctly established at tion ending with the lever in PARK.
MAINTAINING YOUR VEHICLE To prevent dirt and water from entering the transmission after checking or replenishing fluid, make certain that the dipstick cap is properly reseated. It is normal for the dipstick cap to spring back slightly from its fully seated position, as long as its seal remains engaged in the dipstick tube. Automatic Transmission Fluid and Filter Change Refer to “Maintenance Schedule” or further information.
532 MAINTAINING YOUR VEHICLE hot or cold weather and other extreme conditions will Washing have an adverse affect on paint, metal trim, and under• Wash your vehicle regularly. Always wash your vebody protection. hicle in the shade using MOPAR威 Car Wash or equivalent, or a mild car wash soap and rinse the panels The following maintenance recommendations will enable completely with clear water. you to obtain maximum benefit from the corrosion resistance built into your vehicle.
MAINTAINING YOUR VEHICLE CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder which will scratch metal and painted surfaces. 533 • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc.
534 MAINTAINING YOUR VEHICLE heavy soil and/or excessive brake dust, use MOPAR威 • For tough stains, apply MOPAR威 Total Clean or Wheel Cleaner or equivalent or select a nonabrasive, equivalent, or a mild soap solution to a clean, damp non-acidic cleaner. Do not use scouring pads, steel wool, cloth and remove stain. Use a fresh, damp towel to a bristle brush, or metal polishes. Only MOPAR威 or remove soap residue. equivalent is recommended. Do not use oven cleaner.
MAINTAINING YOUR VEHICLE Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and MOPAR威 Total Clean or equivalent. Care should be taken to avoid soaking your leather upholstery with any liquid.
536 MAINTAINING YOUR VEHICLE cleaner. Use caution when cleaning the inside rear window equipped with electric defrosters or the right rear quarter window equipped with the radio antenna. Do not use scrapers or other sharp instruments which may scratch the elements. When cleaning the rearview mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners.
MAINTAINING YOUR VEHICLE cover, otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart.
538 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse J09 30 Amp Pink J10 40 Amp Green J11 30 Amp Pink J12 J13 J14 J15 J16 40 Amp Green 60 Amp Yellow 40 Amp Green 60 Amp Yellow 40 Amp Green Mini Fuse Description Bat – Plg/Electric Brake Bat – L/Bar/Off-Road Bat – Sway/ Thatchum/Rear Doors Starter Solenoid Cavity Cartridge Mini Fuse Fuse M17 25 Amp Natural M18 25 Amp Natural M19 5 Amp Tan M20 Bat – Rad Fan #1/#2/ SSR Bat – Folding Seat/ PZEV Bat – IOD Main M21 Frt HVAC Motor M24 M22 M23 25 Amp Natur
MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse M25 10 Amp Red M26 10 Amp Red M27 15 Amp Blue M28 10 Amp Red M29 M30 M31 M32 15 Amp Blue 25 Amp Natural 20 Amp Yellow 20 Amp Yellow Description Bat – J1962 Diag/ Mirrors Bat – Ign Sw, WIN, PASS Bat – CHMSL/Brake Sw Bat – Corax TPM/ PEM/HVAC Htr Pump Bat – Folding Mirror Bat – Inverter Bat – Pwr Out #1 Fr/Rr Washer Cavity Cartridge Mini Fuse Fuse M33 15 Amp Blue M34 15 Amp Blue M35 20 Amp Yellow M36 20 Amp Yellow M37 10 Amp Red M38 20 Amp Yellow M3
540 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse M41 15 Amp Blue M42 M43 M44 M45 M46 M47 10 Amp Red 10 Amp Red 10 Amp Red 10 Amp Red 20 Amp Yellow 10 Amp Red Description IOD-SDARS/VES 2–3/DVD/HFM/ UGDO/Vanity Lamp IOD-HVAC, U/Hood Lamp Horn #2 IGN R/S-ORC/OCM IGN R-ORC/Trail Tow (BUX) Sense IGN R-Trail Tow (BUX) IGN R-H/Lamp Wash/HVAC/Park Assist/Ir Sns Cavity Cartridge Mini Fuse Fuse M48 20 Amp Yellow M49 20 Amp Yellow M50 25 Amp Natural M51 20 Amp Yellow M52 10 Amp Red M53 15 Amp Blue M54
MAINTAINING YOUR VEHICLE CAUTION! • When installing the totally integrated power module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the totally integrated power module and possibly result in a electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating.
542 MAINTAINING YOUR VEHICLE NOTE: • When reinstalling the IOD fuse push firmly until fully seated; the gauges in the instrument cluster will do a full sweep when the ignition switch is turned to the RUN position. This is a normal condition. • When the vehicle is shipped from the factory, the IOD fuse is in the up or extracted position.
MAINTAINING YOUR VEHICLE 543 BULB REPLACEMENT Dual or Quad Headlamp/Front Park and Turn Signal — If Equipped 1. Open the hood. 2. Disconnect and isolate the negative battery cable. 3. Remove the four plastic push-in fasteners that secure the upper radiator seal to the grille support and both fender ledges. 4. Remove the two plastic push-in rivets that secure the upper radiator seal to the radiator. 7.
544 MAINTAINING YOUR VEHICLE 8. Reach through the access hole of the wheel house 10. Disconnect the wiring harness connectors from the splash shield and lift the slide lock upward far enough to bulb socket. disengage it from the lock post on the back of the front 11. Replace bulb(s) as necessary. lamp unit housing. CAUTION! • Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result.
MAINTAINING YOUR VEHICLE Fog Lamps 545 Rear Tail/Stop, Turn Signal and Backup Lamps 1. Reach under and behind the front bumper to access 1. Remove the two screws that pass through the bed the back of the front fog lamp housing. sheetmetal. 2. Disconnect the fog lamp wiring harness connector from the fog lamp bulb. 3. Rotate the bulb counterclockwise 1⁄4 turn to unlock the bulb from the housing. 4. Pull the bulb straight out from the housing.
546 MAINTAINING YOUR VEHICLE 2. Pull the outboard side of the lamp rearward far 4. Rotate the bulb socket counterclockwise 1/4 turn to enough to unsnap the two receptacles on the outboard unlock it from the housing. side of the lamp housing from the two plastic snap post 5. Pull the bulb straight out of the socket. retainers in the outer box side panel. CAUTION! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces.
MAINTAINING YOUR VEHICLE 547 2. Separate the connector holding the housing and wir- 3. Turn the desired bulb socket 1⁄4 turn and remove the ing harness to the body. socket and bulb from housing.
548 MAINTAINING YOUR VEHICLE 4. Pull the desired bulb straight from the socket. • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High-Mounted Stop Lamp 5. Reverse the procedure for installation of bulbs and housing. Cab Top Clearance Lamps — If Equipped 1. Remove the two screws from the top of the lamp. CAUTION! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result.
MAINTAINING YOUR VEHICLE 549 2. Rotate the socket 1⁄4 turn and pull it from the lamp 3. Pull the bulb straight from it’s socket and replace. assembly.
550 MAINTAINING YOUR VEHICLE Rear Lamp Bar ID Marker (Dual Rear Wheels) — If 2. Turn the socket 1⁄4 turn counterclockwise to access the Equipped bulb. 1. Loosen the two screws and the housing to gain access 3. Pull the bulb straight out from the socket. to the bulb sockets. 4. Reverse the procedure for installation of the bulbs and housing.
MAINTAINING YOUR VEHICLE Side Marker Lamps (Dual Rear Wheels) — If Equipped 551 2. Pull the entire assembly from the fender. 3. Turn the socket 1⁄4 turn counterclockwise and remove from assembly to access the bulb. 4. Pull the bulb straight out from socket. 5. Reverse the procedure for installation of the bulbs and housing. 7 1. Push rearward on the side marker lamp assembly.
552 MAINTAINING YOUR VEHICLE FLUID CAPACITIES Fuel (Approximate) 1500 Regular Cab Shortbed/Crew Quad Cab Models 1500 Regular Cab Longbed/Crew Quad Cab Models (Optional) 2500/3500 Shortbed Models 2500/3500 Longbed Models Engine Oil with Filter 3.7L Engine (SAE 5W-20, API Certified) 4.7L Engine (SAE 5W-20, API Certified) 5.7L Engine (SAE 5W-20, API Certified) 5.7L Engine (SAE 5W-30, API Certified). For 2500/ 3500 trucks operating under a gross combined weight rating greater than 14,000 lbs (6 350 kg). U.S.
MAINTAINING YOUR VEHICLE Cooling System 3.7L Engine (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula or equivalent) 4.7L Engine (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula or equivalent) 5.7L Engine — 1500 Models (MOPAR威 Antifreeze/ Coolant 5 Year/100,000 Mile Formula or equivalent) 5.7L Engine — 2500/3500 Models (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula or equivalent) 5.
554 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Engine Oil Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to your engine oil filler cap for correct SAE grade.
MAINTAINING YOUR VEHICLE 555 Chassis Component Automatic Transmission Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product. Transfer Case MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product. Transfer Case – NVG 246 Only MOPAR威 NVG 246 Automatic Transmission Fluid or equivalent. Front Axle – 1500 Four-Wheel Drive GL-5 SAE 75W-90 (MS-9763) or equivalent.
M A I N T E N A N C ▫ Required Maintenance Intervals . . . . . . . . . . 560 E MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . 558 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 558 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or six months, whichever comes first.
M A I N T E N A N C E S C H E D U L E S 8 560 MAINTENANCE SCHEDULES • Inspect the battery and clean and tighten the terminals Required Maintenance Intervals as required. NOTE: ** Vehicle’s built with the 4.7L engine are • Check the fluid levels of the coolant reservoir, brake equipped with sixteen spark plugs. One set is located on master cylinder, power steering and transmission and the top of the engine under the coils and the second set is add as needed. located on the side of the engine.
MAINTENANCE SCHEDULES 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires. ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only). Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 561 M 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires.
M 562 MAINTENANCE SCHEDULES A I 18,000 Miles (30,000 km) or N T 18 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires. C ❏ Lube the front drive shaft fitting E S C H E D U L E S 8 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule (2500/3500 (4x4) models only). ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
MAINTENANCE SCHEDULES 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only). ❏ Inspect the brake linings, replace if necessary.
M 564 MAINTENANCE SCHEDULES A I 42,000 Miles (70,000 km) or N T 42 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires. C ❏ Lube the front drive shaft fitting E 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
MAINTENANCE SCHEDULES 54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires. ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only). ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
M 566 MAINTENANCE SCHEDULES A I 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule N ❏ Change the engine oil and engine oil filter. T E ❏ Rotate the tires. N ❏ Replace the engine air cleaner filter. A ❏ Replace the ignition cables (3.7L Engine). N ❏ Replace the spark plugs (3.7L and 5.7L Engines). C ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only). E ❏ Inspect the brake linings; replace if necessary.
MAINTENANCE SCHEDULES 66,000 Miles (110,000 km) or 66 Months Maintenance Service Schedule 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only). ❏ Inspect the brake linings; replace if necessary. ❏ Inspect the CV joints.
M 568 MAINTENANCE SCHEDULES A I 78,000 Miles (130,000 km) or N T 78 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires. C ❏ Lube the front drive shaft fitting E 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
MAINTENANCE SCHEDULES 90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate the tires. Replace the engine air cleaner filter. Replace the spark plugs (3.7L and 5.7L Engines). Inspect and replace PCV valve if necessary. † Lube the front drive shaft fitting (2500/3500 (4x4) models only). Inspect the transfer case fluid.
M 570 MAINTENANCE SCHEDULES A I 96,000 Miles (160,000 km) or 96 Months Maintenance Service N T Schedule E ❏ Change the engine oil and engine oil filter. N ❏ Rotate the tires. A ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the N engine air cleaner filter; replace if necessary. C ❏ Replace the top row of spark plugs (4.7L Engine). ** E ❏ Replace the side row of spark plugs (4.7L Engine). ** S C H E D U L E S 8 ❏ ❏ ❏ ❏ ❏ ❏ Replace the ignition cables (4.7L Engine).
MAINTENANCE SCHEDULES 108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only). ❏ Inspect the brake linings; replace if necessary.
M 572 MAINTENANCE SCHEDULES A I 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule N ❏ Change the engine oil and engine oil filter. T E ❏ Rotate the tires. N ❏ Replace the engine air cleaner filter. A ❏ Replace the ignition cables (3.7L Engine). N ❏ Replace the spark plugs (3.7L and 5.7L Engines). C ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only). E ❏ Inspect the brake linings; replace if necessary. S C H E D U L E S 8 ❏ Inspect the CV joints.
MAINTENANCE SCHEDULES 126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires. ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only). ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
M 574 MAINTENANCE SCHEDULES A I 138,000 Miles (230,000 km) or N T 138 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires. C ❏ Lube the front drive shaft fitting E (2500/3500 (4x4) models only). S C H E D U L E S 8 Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires.
MAINTENANCE SCHEDULES 575 M A 150,000 Miles (250,000 km) or 150 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate the tires. Replace the engine air cleaner filter. Replace the spark plugs (3.7L and 5.7L Engines). ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only). ❏ Inspect the transfer case fluid.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 579 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 581 ▫ Prepare For The Appointment . . . . . . . . . . . 579 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 581 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 579 䡵 Warranty Information (U.S. Vehicles Only) . . . .
578 IF YOU NEED CONSUMER ASSISTANCE 䡵 Publication Order Forms . . . . . . . . . . . . . . . . 583 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 585 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 584 ▫ Temperature Grades . . . . . . . . . . . . . . . . . . 585 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 579 the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the for an appointment. right papers with you. Take your warranty folder. All work to be performed may not be covered by the IF YOU NEED ASSISTANCE warranty.
580 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized • Vehicle delivery date and mileage dealer’s service manager first. Most matters can be reChrysler Group LLC Customer Center solved with this process. P.O. Box 21–8004 • If for some reason you are still not satisfied, talk to the Auburn Hills, MI 48321–8004 general manager or owner of the authorized dealer- Phone: (800) 992-1997 ship. They want to know if you need assistance. Chrysler Canada Inc.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
582 IF YOU NEED CONSUMER ASSISTANCE has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns. WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm.
IF YOU NEED CONSUMER ASSISTANCE If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. 583 Transport Canada, Motor Vehicle Defect Investigations and Recalls, 2780 Sheffield Road, Ottawa, Ontario K1B 3V9.
584 IF YOU NEED CONSUMER ASSISTANCE acquaint you with specific Chrysler Group LLC vehicles. Included are starting, operating, emergency and maintenance procedures as well as specifications, capabilities and safety tips. vehicle, system, and/or components is written in straightforward language with illustrations, diagrams, and charts. • Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.
IF YOU NEED CONSUMER ASSISTANCE 585 in each category is shown on the sidewall of the tires on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and your vehicle. concrete. A tire marked C may have poor traction perforAll passenger car tires must conform to Federal safety mance. requirements in addition to these grades.
586 IF YOU NEED CONSUMER ASSISTANCE grade C corresponds to a level of performance, which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law. WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.
INDEX 10
588 INDEX Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 436 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 127 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 512 Air Conditioner Maintenance . . . . . . . . . . . . . . . 514 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 278 Air Conditioning Controls . . . . . . . . . . . . . . . . . 278 Air Conditioning, Operating Tips . . . . . . . . . . . . 290 Air Conditioning Refrigerant . . . . . . . . . .
INDEX 589 Fluid Type . . . . . . . . . . . . . . . . . . . . . . . . 528,555 Brake System . . . . . . . . . . . . . . . . . . . . . . . . 379,525 Anti-Lock (ABS) . . . . . . . . . . . . . . . . . . . . 380,382 Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . . 303 Fluid Check . . . . . . . . . . . . . . . . . . . . . . . . . . 525 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . 525 Special Additives . . . . . .
590 INDEX Radiator (Coolant Pressure) . . . . . . . . . . . . . . . 522 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 532 Carbon Monoxide Warning . . . . . . . . . . . . . . . 78,431 Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Center High Mounted Stop Light . . . . . . . . . . . . 546 Center Lap Belts . . . . . . . . . . . . . . . . . . . . . . . . . 47 Center Seat Storage Compartment . .
INDEX 591 Dipsticks Automatic Transmission . . . . . . . . . . . . . . . . . 529 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 377 Disposal Antifreeze (Engine Coolant) . . . . . . . . . . . . . . . 523 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Door Opener, Garage . . . . . . . . . . . . . . . . . . . . . 145 Driving Off-Pavement . . . . . . . . . . . . . . . . . . . . . . . . . 333 Off-Road . . . . . . . . . . . . . . . . . . . . . . . . . . . .
592 INDEX Electronic Brake Control System . . . . . . . . . . . . . 382 Anti-Lock Brake System . . . . . . . . . . . . . . . . . 382 Brake Assist System . . . . . . . . . . . . . . . . . . . . 384 Electronic Stability Program . . . . . . . . . . . . . . . 388 Traction Control System . . . . . . . . . . . . . . . . . 383 Electronic Range Select (ERS) . . . . . . . . . . . . . . . 308 Electronic Speed Control (Cruise Control) . . . . . . 128 Electronic Stability Program (ESP) . . . . . . . . . . . .
INDEX Exterior Lighting . . . . . . . . . . . . . . . . . . . . . . . . 116 Exterior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 512 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . 511,554 Engine Oil Disposal . . . . . . . . . . . . . . . . . . . . 511 Flashers Turn Signal . . . . . . . . . . . . . . . . . . . . . . 79,121,202 Flat Tire Stowage . . . . . . . . . . . . . . . . . . . . . . . .
594 INDEX Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . 203 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 202 Voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210 Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . 303,310 General Information . . . . . . . . . . . . . . . . . . 17,25,426 Glass Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 535 Grocery Bag Retainer . . . . . . . . . . . . . . . . . . . . .
INDEX Automatic . . . . . . . . . . . . . . . . . . . . . . . . Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . High Beam . . . . . . . . . . . . . . . . . . . . . . . High Beam/Low Beam Select Switch . . . . . Lights On Reminder . . . . . . . . . . . . . . . . . Passing . . . . . . . . . . . . . . . . . . . . . . . . . . Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . Heated Mirrors . . . . . . . . . . . . . . . . . . . . . . Heated Seats . . . . . . . . . . . . . . . . . . . . . .
596 INDEX Jack Location . . . . . . . . . . . . . . . . . . . . . . . . . . . 472 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . . 491 Light Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79,115 Airbag . . . . . . . . . . . . . . . . . . . . . . 51,57,62,79,216 Key, Programming . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Four-Wheel Drive Indicator . . . . . . . . . . . . . . . 318 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 472 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 High Beam . . . . . . . . . . . . . . . . . . . . . . . . 122,210 High Beam Indicator . . . . . . . . . . . . . . . . . . . . 210 High Beam/Low Beam Select . . . . . . . . . . . . . 122 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . 19 Instrument Cluster . . . . . . . . . . . . . . . . . .
598 INDEX Maintenance Schedule . . . . . . . . . . . . . . . . . . . . 558 Malfunction Indicator Light (Check Engine) . . . . . 506 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . 583 Manual Transmission Fluid Level Check . . . . . . . . . . . . . . . . . . . . . 528 Lubricant Selection . . . . . . . . . . . . . . . . . . . . . 555 Memory Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 Mini-Trip Computer . . . . . . . . . . . . . . . . . . . . . . 228 Mirrors . . . . . . .
INDEX Dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 509 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511,554 Filter Disposal . . . . . . . . . . . . . . . . . . . . . . . . 511 Identification Logo . . . . . . . . . . . . . . . . . . . . . 510 Materials Added to . . . . . . . . . . . . . . . . . . . . . 511 Pressure Gauge . . . . . . . . . . . . . . . . . . . . . . . 205 Recommendation . . . . . . . .
600 INDEX Sliding Rear Window . . . . . . . . . . . . . . . . . . . 172 Steering . . . . . . . . . . . . . . . . . . . . . . . . . . 376,377 Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Power Steering Fluid . . . . . . . . . . . . . . . . . . . . . 555 Pregnant Women and Seat Belts . . . . . . . . . . . . . . 49 Pretensioners Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Reporting Safety Defects . . . . . . . . . . . . . . . . . . . 582 Resetting Oil Change Indicator . . . . . . . . . . . 208,226 Restraint, Head . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Restraints, Child . . . . . . . . . . . . . . . . . . . . . . . 64,70 Restraints, Occupant . . . . . . . . . . . . . . . . . . . . . . 37 Rotation, Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 414 Safety Checks Inside Vehicle . . . . . . . . . . . . . . . . .
602 INDEX Selection of Coolant (Antifreeze) . . . . . . . . . . 521,554 Sentry Key (Immobilizer) . . . . . . . . . . . . . . . . . . . 15 Sentry Key Programming . . . . . . . . . . . . . . . . . . . 17 Sentry Key Replacement . . . . . . . . . . . . . . . . . . . 16 Service Assistance . . . . . . . . . . . . . . . . . . . . . . . 579 Service Contract . . . . . . . . . . . . . . . . . . . . . . . . . 581 Service Manuals . . . . . . . . . . . . . . . . . . . . . . . . 583 Setting the Clock . . . . . . . . .
INDEX Steering Wheel Mounted Sound System Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276 Storage Compartment, Center Seat . . . . . . . . . . . 166 Storage, Vehicle . . . . . . . . . . . . . . . . . . . . . . 289,541 Storing Your Vehicle . . . . . . . . . . . . . . . . . . . . . . 541 Sun Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 Supplemental Tire Pressure Information . . . . . . . . 411 Sway Control, Trailer . . . . . . . . . . . . . . . . . . . . .
604 INDEX Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 394,404 Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 414 Spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . 409 Tongue Weight/Trailer Weight . . . . . . . . . . . . . . 445 Torque Converter Clutch . . . . . . . . . . . . . . . . 307,313 Tow Hooks, Emergency . . . . . .
INDEX 605 Transmitter, Remote Keyless Entry (RKE) . . . . . . . . 20 Voice Recognition System (VR) . . . . . . . . . . . . . . . 94 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . 409 Voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210 Trip Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . 206 Turn Signals . . . . . . . . . . . . . . . . . . . 121,202,543,545 Warning Lights (Instrument Cluster Description) . . . . . . . . . . 198,202 UCI Connector . . . . . . .
606 INDEX Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356 Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 37,154 Window Fogging . . . . . . . . . . . . . . . . . . . . . . . . 289 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Rear Sliding . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Windshield Defroster . . . . . . . . . . . . . . . . . . . . . .
Chrysler Group LLC 10D241-126-AB 2nd Edition Printed in U.S.A.
