2014 Challenger SRT Chrysler Group LLC 14D492-126-AA First Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 VEHICLE IDENTIFICATION NUMBER . . . . . . . .6 䡵 HOW TO USE THIS MANUAL . . . . . . . . . . . . . .4 䡵 VEHICLE MODIFICATIONS/ALTERATIONS . . . .7 䡵 WARNINGS AND CAUTIONS . . . . . . . . . . . . . .
4 INTRODUCTION When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained techCongratulations on selecting your new Chrysler Group nicians and genuine parts, and cares about your satisfacLLC vehicle. Be assured that it represents precision tion. workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owners Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is on the left front corner of the instrument panel.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. VIN Location NOTE: It is illegal to remove or alter the VIN.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A WORD ABOUT YOUR KEYS . . . . . . . . . . . . .12 ▫ Rearming Of The System . . . . . . . . . . . . . . . . .20 ▫ Wireless Ignition Node (WIN) . . . . . . . . . . . . .12 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . . .20 ▫ Key Fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .21 ▫ Removing Key Fob From Ignition . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Programming Additional Transmitters. . . . . . . .27 䡵 TRUNK SAFETY WARNING. . . . . . . . . . . . . . . .43 ▫ Transmitter Battery Replacement . . . . . . . . . . .27 ▫ Trunk Emergency Release . . . . . . . . . . . . . . . .44 ▫ General Information . . . . . . . . . . . . . . . . . . . .28 䡵 OCCUPANT RESTRAINTS . . . . . . . . . . . . . . . .44 䡵 REMOTE STARTING SYSTEM — IF EQUIPPED . . .29 ▫ Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Supplemental Restraint System (SRS) — 䡵 SAFETY TIPS . . . . . . . . . . . . . . . . . . . . . . . Air Bags . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 ▫ Transporting Passengers. . . . . . . . . . . . . . . ▫ Air Bag Deployment Sensors And Controls . . . .64 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . ▫ Event Data Recorder (EDR) . . . . . . . . . . . . . . .71 ▫ Safety Checks You Should Make Inside The ▫ Child Restraints . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE is a spring-loaded momentary contact position. When released from the START position, the switch automatiYour vehicle uses a keyless ignition system. This system cally returns to the ON/RUN position. consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with NOTE: If your vehicle is equipped with Keyless Enterintegral ignition switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired position. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To remove the emergency key, slide the mechanical latch Removing Key Fob From Ignition on the Key Fob sideways with your thumb and then pull Place the shift lever in PARK or place the manual the key out with your other hand. transmission in REVERSE and apply the parking brake. Turn the Key Fob to the OFF position and then remove the Key Fob. With the Keyless Enter-N-Go™ system, the EVIC will display the ignition switch position “OFF/ACC/RUN”.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 NOTE: The power window switches, radio, power sunroof — if equipped, and ignition-powered power outlets will remain active for up to 60 minutes after the ignition switch is turned to the LOCK position. Opening either door will cancel this feature. The time for this feature is programmable. Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (CustomerProgrammable Features)” in “Understanding Your Instrument Panel” for further information.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever. • Do not leave the Key Fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/RUN mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 If your vehicle is equipped with Keyless Enter-N-Go™, opening the driver’s door when the vehicle’s ignition switch is placed in ACC or ON/RUN (engine stopped) will cause the reminder chime to sound. Refer to “Starting Procedures” in “Starting And Operating” for further information. system will shut the engine off in two seconds if an invalid Key Fob is used to start the engine.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! CAUTION! The Sentry Key® Immobilizer system is not compatible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. • Always remove the Key Fobs from the vehicle and lock all doors when leaving the vehicle unattended. • For vehicles equipped with Keyless Enter-N-Go™, always remember to place the ignition in the OFF position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: When having the Sentry Key® Immobilizer Sys- NOTE: Changes or modifications not expressly approved tem serviced, bring all vehicle Key Fobs with you to the by the party responsible for compliance could void the user’s authority to operate the equipment. authorized dealer.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Rearming Of The System If something triggers the alarm, and no action is taken to disarm it, the Vehicle Security Alarm will turn the horn off after three minutes, turn all of the visual signals off after an additional 15 minutes, and then the Vehicle Security Alarm will rearm itself. To Arm The System Follow these steps to arm the Vehicle Security Alarm: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 NOTE: The driver’s door key cylinder and the trunk The Vehicle Security Alarm can be disarmed using any of button on the RKE transmitter cannot arm or disarm the Vehicle Security Alarm. the following methods: To Disarm The System • The Vehicle Security Alarm remains armed during trunk entry. Pressing the trunk button will not disarm the Vehicle Security Alarm.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the Vehicle Security Alarm is armed and the battery becomes disconnected, the Vehicle Security Alarm will remain armed when the battery is reconnected; the exterior lights will flash, the horn will sound. If this occurs, disarm the Vehicle Security Alarm. ILLUMINATED ENTRY The courtesy lights will turn on when you use the Remote Keyless Entry (RKE) transmitter to unlock the doors or open any door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • The Illuminated Entry system will not operate if the dimmer control is in the “Dome defeat” position (extreme bottom position). 2 REMOTE KEYLESS ENTRY (RKE) The RKE system allows you to lock or unlock the doors, open the trunk, or activate the Panic Alarm from distances up to approximately 66 ft (20 m) using a hand-held Key Fob with RKE transmitter. The RKE transmitter does not need to be pointed at the vehicle to activate the system.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If equipped with Keyless Enter-N-Go™ (Passive Entry), 3. Test the feature while outside of the vehicle by pressing the LOCK/UNLOCK buttons on the RKE transrefer to “Keyless Enter-N-Go™” under “Things To Know mitter with the ignition switch in the OFF position and Before Starting Your Vehicle” for further information. the Key Fob removed. Remote Key Unlock, Driver Door/All Doors First This feature lets you program the system to unlock either 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Settings (Customer-Programmable Features)” in “Under- NOTE: Pressing the LOCK button on the RKE transmitstanding Your Instrument Panel” for further information. ter while you are in the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated • When not using the EVIC, perform the following steps: will cause the alarm to sound. Press the UNLOCK button 1.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If equipped with Keyless Enter-N-Go™ (Passive Entry), 2. Release both buttons at the same time. refer to “Keyless Enter-N-Go™” under “Things To Know 3. Test the feature while outside of the vehicle by pressBefore Starting Your Vehicle” for further information. ing the LOCK button on the RKE transmitter with the Sound Horn With Remote Key Lock ignition switch in the OFF position and the Key Fob removed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 If equipped with Keyless Enter-N-Go™ (Passive Entry), NOTE: refer to “Keyless Enter-N-Go™” under “Things To Know • The interior lights will turn off if you turn the ignition Before Starting Your Vehicle” for further information. switch to the ACC or ON/RUN position while the Panic Alarm is activated. However, the exterior lights Using The Panic Alarm and horn will remain on.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Perchlorate Material – special handling may apply. General Information See www.dtsc.ca.gov/hazardouswaste/perchlorate This device complies with Part 15 of the FCC rules and 1. If the RKE transmitter is equipped with a screw, RSS 210 of Industry Canada. Operation is subject to the remove the screw. With the RKE ransmitter buttons following conditions: facing down, use a flat blade to pry the two halves of • This device may not cause harmful interference.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 2. Closeness to a radio transmitter such as a radio station How To Use Remote Start tower, airport transmitter, and some mobile or CB All of the following conditions must be met before the radios.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Monoxide (CO) which is odorless and colorless. Carbon Monoxide is poisonous and can cause serious injury or death when inhaled. • Keep Remote Keyless Entry (RKE) transmitters away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 To Exit Remote Start Mode Without Driving The Vehicle Press and release the REMOTE START button one time or allow the engine to run for the entire 15-minute cycle. NOTE: • For vehicles not equipped with the Keyless Enter-NGo™ feature, the ignition switch must be in the ON/RUN position in order to drive the vehicle.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Any engine warning lights come on • Low Fuel Light turns on • The hood is opened • The hazard switch is pressed • The shift lever is moved out of PARK • The brake pedal is pressed DOOR LOCKS Manual Door Locks Door Lock Knob To lock each door, push the door lock knob on each door If the door lock knob is down when you shut the door, trim panel downward. To unlock each door, pull the door the door will lock.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! WARNING! (Continued) • For personal security and safety in the event of a collision, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • When leaving the vehicle, always remove the Key Fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks The power door lock switch is located on each door trim panel. Use this switch to lock or unlock the doors. The doors can also be locked and unlocked with the Keyless Enter-N-Go™ (Passive Entry) system. For further information, refer to “Keyless Enter-N-Go™” in “Things To Know Before Starting Your Vehicle”. If you press the power door lock switch while the Key Fob is in the ignition, and either door is open, the power locks will not operate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 authorized dealer per written request of the customer. Automatic Unlock Doors On Exit Programming Please see your authorized dealer for service. The Automatic Unlock Doors On Exit feature can be enabled or disabled. Refer to “Electronic Vehicle InforAutomatic Unlock Doors On Exit mation Center (EVIC)/Personal Settings (CustomerThe doors will unlock automatically if: Programmable Features)” in “Understanding Your In1.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE handle to unlock the driver’s door automatically. The interior door panel lock knob will raise when the door is • Passive Entry may be programmed ON/OFF; refer to unlocked. “Electronic Vehicle Information Center (EVIC)/ Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 NOTE: If “Unlock All Doors 1st Press” is programmed all doors will unlock when you grab hold of the front driver’s door handle. To select between “Unlock Driver Door 1st Press” and “Unlock All Doors 1st Press”, refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If you inadvertently leave your vehicle’s Passive Entry RKE transmitter in the trunk and try to close the With a Passive Entry RKE transmitter within 5 ft (1.5 m) deck lid, the deck lid will automatically unlatch, unless of the deck lid, press the button on the located on the another one of the vehicle’s Passive Entry RKE transmitcenter of the light bar which is located on the deck lid ters is outside the vehicle and within 5 ft (1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 To Lock The Vehicle’s Doors: With one of the vehicle’s Passive Entry RKE transmitters within 5 ft (1.5 m) of the driver or passenger front door handles, press the door handle LOCK button to lock both doors. Do NOT grab the door handle, when pressing the door handle lock button. This could unlock the door(s).
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • After pressing the door handle LOCK button, you must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking. • The Passive Entry system will not operate if the RKE transmitter battery is dead.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 NOTE: • The Key Off Power Delay feature will allow the power windows to operate for up to 10 minutes after the ignition is turned OFF. This feature is cancelled when either front door is opened. The time for this feature is programmable. Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer- Programmable Features)” in “Understanding Your Instrument Panel” for further information.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To open the window part way, press the window switch open or partially open positions. This is a normal occurto the first detent and release it when you want the rence and can be minimized. If the buffeting occurs with one window open, then open the other window to window to stop. minimize the buffeting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 NOTE: The transmission must be in PARK before the With the ignition switch in the OFF position or the key button will operate. If equipped with a manual transmis- removed from the ignition switch, the Trunk Open symsion, the vehicle speed must be under 5 mph (8 km/h) bol will display until the trunk is closed. before the button will operate.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Trunk Emergency Release As a security measure, a Trunk Internal Emergency Release lever is built into the trunk latching mechanism. In the event of an individual being locked inside the trunk, the trunk can be simply opened by pulling on the glow-in-the-dark handle attached to the trunk latching mechanism.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 • Advanced Front Air Bags for driver and front passenger • Supplemental Side Air Bag Inflatable Curtains (SABIC) for the driver and passengers seated next to a window all the way out and then adjusting the belt to the desired length to restrain a child seat or secure a large item in a seat — if equipped Please pay close attention to the information in this • Supplemental Seat-Mounted Side Air Bags (SAB) for section.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some simple steps you can take to minimize the ride properly buckled up in the rear seat. Never allow risk of harm from a deploying air bag: children to slide the shoulder belt behind them or under their arm. 1. Children 12 years old and under should always ride If a child from 2 to 12 years old (not in a rear facing child buckled up in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 4. Do not lean against the door or window. If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between you and the door. 5. If the air bag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided under ⴖIf You Need Assistanceⴖ. WARNING! • Relying on the air bags alone could lead to more severe injuries in a collision.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) Lap/Shoulder Belts • Being too close to the Supplemental Side Air Bag Inflatable Curtain (SABIC) and/or Seat-Mounted Side Air Bag (SAB) during deployment could cause you to be severely injured or killed. All seating positions in your vehicle are equipped with lap/shoulder belts. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 WARNING! (Continued) • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision best. • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Latch Plate 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 WARNING! WARNING! (Continued) • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snug.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt cannot do its job as well. In a collision, it could even cut into you. Be sure the belt is straight.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.). Lap/Shoulder Belt Untwisting Procedure 2.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE First Row Second Row Driver N/A ALR Center N/A ALR Passenger ALR ALR Automatic Locking Retractor Mode (ALR) — If Equipped In this mode, the shoulder belt is automatically prelocked. The belt will still retract to remove any slack in • N/A — Not Applicable the shoulder belt. The Automatic Locking Mode is available on all passenger-seating positions with a combina• ALR — Automatic Locking Retractor tion lap/shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 3. Allow the belt to retract. As the belt retracts, you will Energy Management Feature hear a clicking sound. This indicates the safety belt is This vehicle has a safety belt system with an Energy now in the Automatic Locking Mode. Management feature in the front seating positions to help further reduce the risk of injury in the event of a head-on How To Disengage The Automatic Locking Mode collision.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: These devices are not a substitute for proper seat Reminder Light and sounding an intermittent chime. belt placement by the occupant. The seat belt still must be Once the sequence starts, it will continue for the entire duration or until the respective seatbelts are fastened. worn snugly and positioned properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 BeltAlert® can be enabled or disabled by your autho- Seat Belt Extender rized dealer. Chrysler Group LLC does not recommend If a seat belt is too short even when fully extended and deactivating BeltAlert®.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Restraint System (SRS) — Air Bags This vehicle has Advanced Front Air Bags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s Advanced Front Air Bag is mounted in the center of the steering wheel. The passenger’s Advanced Front Air Bag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the air bag covers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 The Advanced Front Air Bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severity and type of collision. This vehicle is equipped with Supplemental Side Air Bag Inflatable Curtains (SABIC) to protect the driver, front, and rear passengers sitting next to a window. The SABIC air bags are located above the side windows and their covers are labeled: SRS AIRBAG.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Steering Wheel and Column • Instrument Panel • Knee Impact Bolsters • Driver Advanced Front Air Bag • Passenger Advanced Front Air Bag • Supplemental Seat-Mounted Side Air Bags (SAB) • Supplemental Side Air Bag Inflatable Curtains (SABIC) • Front and Side Impact Sensors • Front Seat Belt Pretensioners, Seat Belt Buckle Switch, and Seat Track Position Sensors Advanced Front Air Bag Features The Advanced Front Air Bag system has multistage driver and front pas
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 WARNING! (Continued) • Do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air bags are inflating. • Do not drill, cut or tamper with the knee bolster in any way.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Side Air Bag Inflatable Curtain (SABIC) SABIC air bags may offer side-impact protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each air bag features inflated chambers placed adjacent to the head of each outboard occupant that reduce the potential for sideimpact head injuries. The curtains deploy downward, covering both windows on the impact side.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 The system includes side impact sensors that are calibrated to deploy the side air bags during impacts that require air bag occupant protection. WARNING! • Your vehicle is equipped with left and right Supplemental Side Air Bag Inflatable Curtain (SABIC), do not stack luggage or other cargo up high enough to block the location of the SABIC. The area where the SABIC is located should remain free from any obstructions.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Always sit upright as possible with your back against the seat back, use the seat belts properly, and use the appropriate sized child restraint, infant restraint or booster seat recommended for the size and weight of the child. Knee Impact Bolsters The ORC determines if deployment of the front and/or side air bags in a frontal or side collision is required.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 impact, Advanced Front Air Bags may deploy in crashes The ORC contains a backup power supply system that with little vehicle front-end damage but that produce a may deploy the air bags even if the battery loses power or severe initial deceleration. it becomes disconnected prior to deployment. The side air bags will not deploy in all side collisions. Side air bag deployment will depend on the severity and type of collision.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the Air Bag Warning Light in your instrument panel could mean you won’t have the air bags to protect you in a collision. If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 The ORC determines if a side collision requires the side and type of collision. In these events, the ORC will air bags to inflate, based on the severity and type of deploy the SABIC only on the impact side of the vehicle. collision. A quantity of non-toxic gas is generated to inflate the side Based on the severity and type of collision, the side air curtain air bag.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front And Side Impact Sensors • Unlock the doors automatically. In front and side impacts, impact sensors can aid the In order to reset the Enhanced Accident Response System ORC in determining appropriate response to impact functions after an event, the ignition switch must be events. changed from IGN ON to IGN OFF.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 you might get sliding along a carpet or gymnasium Do not drive your vehicle after the air bags have defloor. They are not caused by contact with chemicals. ployed. If you are involved in another collision, the air They are not permanent and normally heal quickly. bags will not be in place to protect you. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor WARNING! immediately.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Air Bag System WARNING! (Continued) WARNING! • Modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Air Bag Warning Light NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to “Fuses” in “Maintaining Your Vehicle” for the proper air bag fuses. See your authorized dealer if the fuse is good.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Whether or not the driver and passenger safety belts To read data recorded by an EDR, special equipment is were buckled/fastened; required, and access to the vehicle or the EDR is needed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 WARNING! In a collision, an unrestrained child can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Summary Of Recommendations For Restraining Children In Vehicles Infants and Toddlers Small Children Larger Children Children Too Large for Child Restraints Child Size, Height, Weight Or Age Children who are two years old or younger and who have not reached the height or weight limits of their child restraint Children who are at least two years old or who have out-grown the height or weight limit of their rear-facing child restraint Children who have out-gr
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Infants And Child Restraints Safety experts recommend that children ride rearwardfacing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carriers and convertible child seats. The infant carrier is only used rearward-facing in the vehicle.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat belts fit properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Children Too Large For Booster Seats 3. Does the shoulder belt cross the child’s shoulder between their neck and arm? Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend 4. Is the lap part of the belt as low as possible, touching over the front of the seat when their back is against the the child’s thighs and not their stomach? seatback, should use the seat belt in a rear seat. Use this 5.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Recommendations For Attaching Child Restraints Restraint Type Combined Weight of the Child + Child Restraint Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Lower Anchors And Tethers For Children (LATCH) Restraint System Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCHequipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH Positions For Installing Child Restraints In This Vehicle • • Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? Can the LATCH anchorages and the seat belt be used together to attach a rear-facing or forward-facing child restraint? Can a child seat be installed in the center position using the inner LATCH lower anchorages? Can two child restraints be attached using a common lower LATCH anchorage? 65 lbs (29.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the head restraints be removed? No The child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint owner’s manual for more information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 Locating The LATCH Anchorages In addition, there are tether strap anchorages behind each rear seating position located in the panel between the rear seatback and the rear window. These tether strap anchorages are under a plastic cover with the tether anchorage symbol on it. 2 Tether Strap Anchorages LATCH-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE tether strap. The tether strap will have a hook at the end Always follow the directions of the child restraint manuto attach to the top tether anchorage and a way to tighten facturer when installing your child restraint. Not all child restraint systems will be installed as described here. the strap after it is attached to the anchorage.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 restraint to get a better fit. If the rear seat can be moved 7. Test that the child restraint is installed tightly by forward and rearward in the vehicle, you may wish to pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) move it to its rear-most position to make room for the in any direction. child seat. You may also move the front seat forward to allow more room for the car seat.
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • Child restraint anchorages are designed to withstand only those loads imposed by correctly-fitted child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 Lap/Shoulder Belt Systems for Installing Child Restraints in this Vehicle 2 What is the weight limit (child’s weight + weight of the child restraint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? Weight limit of the Child Restraint Always use the tether anchor when using the seat belt to install a forward facing child restraint, up to the recommended weight limit of the child restraint.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the head restraints be removed? Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint? No Yes Installing A Child Restraint With A Switchable Automatic Locking Retractor (ALR) Contact between the front passenger seat and the child restraint is allowed, if the child restraint manufacturer also allows contact.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 out of the retractor. Then, allow the webbing to retract 9. Test that the child restraint is installed tightly by back into the retractor. As the webbing retracts, you pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) will hear a clicking sound. This means the seat belt is in any direction. now in the Automatic Locking mode. 6. Try to pull the webbing out of the retractor.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Next, pull enough of the seat belt webbing from the Any seat belt system will loosen with time, so check the retractor to pass it through the belt path of the child belt occasionally, and pull it tight if necessary. restraint. Do not twist the belt webbing in the belt path. If the buckle or the cinching latch plate is too close to the 3. Slide the latch plate into the buckle until you hear a belt path opening of the child restraint, you may have “click”.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 Installing Child Restraints Using The Top Tether Anchorage restraint and pass the tether strap around the outboard side of the head restraint. 2 Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage.
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Attach the tether strap hook of the child restraint to Transporting Pets the top tether anchorage as shown in the diagram. Air Bags deploying in the front seat could harm your pet. 4. Remove slack in the tether strap according to the child An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in restraint manufacturer’s instructions. a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. However, wide-open throttle acceleration in low gear can be detrimental and should be avoided. The engine oil is a high performance synthetic lubricant, the transmission fluid and axle lubricant installed at the factory is high-quality and energy-conserving.
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. WARNING! • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 The best protection against carbon monoxide entry into Front seat belt assemblies must be replaced after a the vehicle body is a properly maintained engine exhaust collision. Rear seat belt assemblies must be replaced after system. a collision if they have been damaged (i.e., bent retractor, torn webbing, etc.).
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Floor Mat Safety Information WARNING! (Continued) Always use floor mats designed to fit the footwell of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 WARNING! (Continued) • Always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • If required, mounting posts must be properly installed, if not equipped from the factory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .110 ▫ Automatic Dimming Mirror — If Equipped . . .104 ▫ Phone Call Features . . . . . . . . . . . . . . . . . . . .118 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . .105 ▫ Uconnect® Phone Features . . . . . . . . . . . . . .121 ▫ Outside Mirrors Folding Feature . . . . . . . . . .
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Voice Training . . . . . . . . . . . . . . . . . . . . . . . .145 䡵 SEATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145 ▫ Power Seats . . . . . . . . . . . . . . . . . . . . . . . . .146 ▫ Heated Seats — If Equipped . . . . . . . . . . . . .148 ▫ Manual Forward Or Rearward Adjustment . . .149 ▫ Manual Front Seatback Recline . . . . . . . . . . . .150 ▫ Passenger Seat Easy Entry . . . . . . . . . . . . . . .151 ▫ Head Restraints . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 䡵 WINDSHIELD WIPERS AND WASHERS . . . . . .164 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . .171 ▫ Intermittent Wiper System . . . . . . . . . . . . . . .165 ▫ To Accelerate For Passing . . . . . . . . . . . . . . . .172 ▫ Mist Feature . . . . . . . . . . . . . . . . . . . . . . . . .165 䡵 PARKSENSE® REAR PARK ASSIST — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . .173 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . .
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Sunglasses Storage . . . . . . . . . . . . . . . . . . . .181 ▫ Closing Sunroof — Express. . . . . . . . . . . . . . .191 䡵 GARAGE DOOR OPENER — IF EQUIPPED . . .181 ▫ Closing Sunroof — Manual Mode . . . . . . . . . .191 ▫ Before You Begin Programming HomeLink® . .182 ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . . .192 ▫ Programming A Rolling Code . . . . . . . . . . . .183 ▫ Venting Sunroof — Express . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 䡵 CONSOLE FEATURES . . . . . . . . . . . . . . . . . . .199 䡵 REAR WINDOW FEATURES . . . . . . . . . . . . . .200 ▫ Sliding Center Console Armrest . . . . . . . . . . .199 ▫ Rear Window Defroster . . . . . . . . . . . . . . . . .200 ▫ Console Storage. . . . . . . . . . . . . . . . . . . . . . .
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated. The sensor to the right of the button does not illuminate. NOTE: This feature is disabled when the vehicle is moving in reverse.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Outside Mirrors Outside Mirrors Folding Feature To receive maximum benefit, adjust the outside mirror(s) The mirrors are equipped with a rotational hinge. The to center on the adjacent lane of traffic and a slight mirrors have one detent (clockwise) towards the rear of overlap of the view obtained from the inside mirror. the vehicle and three detent’s (counterclockwise) towards the front of the vehicle.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Mirrors The power mirror controls are located on the driver’s door trim panel. To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When you are finished adjusting the mirror, turn the control to the center position to prevent accidentally moving a mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster (if equipped). Refer to “Rear Window Features” in “Understanding The Features Of Your Vehicle” for further information. 3 Illuminated Vanity Mirrors An illuminated vanity mirror is on the sun visor. To use the mirror, rotate the sun visor downward and swing the mirror cover upward.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE desired position. To use the extender feature of the sun Uconnect® PHONE — IF EQUIPPED visor, grab the extender which is located at the rear of the Uconnect® Phone is a voice-activated, hands-free, invisor and pull rearward. vehicle communications system. Uconnect® Phone allows you to dial a phone number with your mobile phone using simple voice commands (e.g., “Call” ѧ “Mike” ѧ “Work” or “Dial” ѧ “248-555-1212”).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Uconnect® Phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The Uconnect® Phone is driven through your Bluetooth® “Hands-Free Profile” mobile phone.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Command Button Operation Actual button location may vary with the ra- Voice commands can be used to operate the Uconnect® dio. The individual buttons are described in the Phone and to navigate through the Uconnect® Phone menu structure. Voice commands are required after most “Operation” section. Uconnect® Phone prompts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 example, you can use the compound form voice command “Phonebook New Entry,” or you can break the compound form command into two voice commands: “Phonebook” and “New Entry.” Please remember, the Uconnect® Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you. To activate the Uconnect® Phone, simply press the button and follow the audible prompts for directions.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The following are general phone to Uconnect® Phone • You will then be asked to give your mobile phone a priority level between one and seven, with one being pairing instructions: the highest priority. You can pair up to seven mobile button to begin. • Press the phones to your Uconnect® Phone. However, at any given time, only one mobile phone can be in use, • After the “Ready” prompt and the following beep, say “Device Pairing.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 • The system will prompt you to say the number you want to call. • For example, you can say “234 567 8901.” • The Uconnect® Phone will confirm the phone number and then dial. The number will appear in the display of certain radios. Call By Saying A Name • Press the button to begin. or downloaded phonebook. To learn how to store a name in the phonebook, refer to “Add Names to Your Uconnect® Phonebook,” in the phonebook.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Automatic download and update, if supported, begins • This downloaded phonebook cannot be edited or as soon as the Bluetooth® wireless phone connection is deleted on the Uconnect® Phone. These can only be edited on the mobile phone. The changes are transmade to the Uconnect® Phone, for example, after you ferred and updated to Uconnect® Phone on the next start the vehicle. phone connection.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 • When prompted, enter the number designation (e.g., Edit Uconnect® Phonebook Entries “Home,” “Work,” “Mobile,” or “Other”). This will NOTE: allow you to store multiple numbers for each phone• Editing names in the phonebook is recommended book entry, if desired. when the vehicle is not in motion. • When prompted, recite the phone number for the • Automatic downloaded phonebook entries cannot be phonebook entry that you are adding. deleted or edited.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After you are finished editing an entry in the phonebook, • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish you will be given the opportunity to edit another entry in to delete. You can either say the name of a phonebook the phonebook, call the number you just edited, or return entry that you wish to delete or you can say “List to the main menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Delete/Erase “All” Uconnect® Phonebook Entries List All Names In The Uconnect® Phonebook • Press the • Press the button to begin. button to begin. • After the “Ready” prompt and the following beep, say • After the “Ready” prompt and the following beep, say “Phonebook Erase All.” “Phonebook List Names.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer Or Reject An Incoming Call — Call The following features can be accessed through the Currently In Progress Uconnect® Phone if the feature(s) are available on your If a call is currently in progress and you have another mobile service plan.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 in progress. To go back to the first call, refer to “Toggling Conference Call Between Calls” in this section. To combine two calls, refer When two calls are in progress (one active and one on to “Conference Call” in this section. button until you hear a hold), press and hold the double beep indicating that the two calls have been Place/Retrieve A Call From Hold joined into one conference call.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE active call is terminated by the phone far end, a call on Call Continuation hold may not become active automatically. This is cell Call continuation is the progression of a phone call on the phone-dependent. To bring the call back from hold, press Uconnect® Phone after the vehicle ignition key has been button until you hear a single beep. and hold the switched to OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Uconnect® Phone Features Emergency Assistance Language Selection If you are in an emergency and the mobile phone is reachable: To change the language that the Uconnect® Phone is using: • Pick up the phone and manually dial the emergency number for your area. button to begin.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • The emergency number dialed is based on the country where the vehicle is purchased (911 for the U.S. and Canada and 060 for Mexico). The number dialed may not be applicable with the available mobile service and area. WARNING! To use your Uconnect® Phone System in an emergency, your mobile phone must be: • turned on, • paired to the Uconnect® System, • and have network coverage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 NOTE: You should program the desired Towing Assistance phone number using the Voice Command system. To do this, press the button and say “Setup,” followed by “Towing Assistance.” When prompted say 1-800-5212779 for U.S./Canada, say 55-14-3454 for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE “Send,” is also to be used for navigating through an • Some paging and voice mail systems have system time out settings that are too short and may not allow the automated customer service center menu structure, and use of this feature. to leave a number on a pager. You can also send stored Uconnect® phonebook entries as tones for fast and easy access to voice mail and pager entries. To use this feature, dial the number you wish to button and say “Send.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 • After the “Ready” prompt and the following beep, say dialing a number with your paired Bluetooth® mobile phone, the audio will be played through your vehicle’s one of the following: audio system. The Uconnect® Phone will work the same – “Setup Confirmation Prompts On” as if you dial the number using Voice Command.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Following the beep, say “Mute.” To un-mute the Uconnect® Phone: • Press the button. • Following the beep, say “Mute off.” Connect Or Disconnect Link Between The Uconnect® Phone And Mobile Phone Your mobile phone can be paired with many different electronic devices, but can only be actively “connected” with one electronic device at a time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 • The Uconnect® Phone will play the phone names of all • The selected phone will be used for the next phone call. If the selected phone is not available, the paired mobile phones in order from the highest to the Uconnect® Phone will return to using the highest lowest priority. To “Select” or “Delete” a paired phone priority phone present in or near (approximately button and say “Sebeing announced, press the within 30 ft (9 m)) the vehicle. lect” or “Delete.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Things You Should Know About Your Uconnect® Phone Uconnect® Phone Tutorial • Press the button and say the “Voice Training,” “System Training,” or “Start Voice Training” command. To hear a brief tutorial of the system features, press the You can either press the Uconnect® Phone button to restore the factory setting or repeat the words and button and say “Uconnect® Tutorial.” phrases when prompted by the Uconnect® Phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 This will delete all phone pairing, phone book entries, • Low-to-medium vehicle speed and other settings in all language modes. The System will • Low road noise prompt you before resetting to factory settings. • Smooth road surface Voice Command • Fully closed windows • For best performance, adjust the rearview mirror to provide at least ½ inch (1 cm) gap between the • Dry weather condition overhead console (if equipped) and the mirror.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Phonebook (Downloaded and Uconnect® Phone Lo- • cal) name recognition rate is optimized when the • entries are not similar. • • Numbers must be spoken in single digits. “800” must • be spoken “eight-zero-zero” not “eight hundred.” • You can say “O” (letter “O”) for “0” (zero). Low road noise Smooth road surface Fully closed windows Dry weather conditions, and • Operation from the driver’s seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Recent Calls • Uconnect® Phone will play the new text message for you. If your phone supports “Automatic Phonebook Download,” Uconnect® Phone can list your Outgoing, Incom- After reading a message, you can “Reply” or “Forward” ing and Missed Calls. the message using Uconnect® Phone. SMS Send Messages: Uconnect® Phone can read or send new messages on You can send messages using Uconnect® Phone. To send your phone.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE button while the 10. To send a message, press the system is listing the message and say “Send.” 11. Uconnect® Phone will prompt you to say the name or 12. number of the person you wish to send the message to. 13. List of Preset Messages: 14. 1. Yes 15. 2. No 16. 3. Where are you? 17. 4. I need more direction 18. 5. L O L 19. 6. Why 20. 7. I love you 8. Call me 9.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Turn SMS Incoming Announcement ON/OFF Bluetooth® Communication Link Turning the SMS Incoming Announcement OFF will stop Mobile phones have been found to lose connection to the the system from announcing the new incoming mes- Uconnect® Phone. When this happens, the connection can generally be reestablished by switching the phone sages. off/on. Your mobile phone is recommended to remain in button. • Press the Bluetooth® ON mode.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 3
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Voice Commands Primary Alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location Voice Commands Primary Alternate (s) all call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais 3
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Primary Alternate (s) help home language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book Voice Commands Primary Alternate (s) previous record again redial return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call Uconnect® Tutorial voice training work yes
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 General Information VOICE COMMAND — IF EQUIPPED This device complies with Part 15 of the FCC rules and Voice Command System Operation RSS 210 of Industry Canada.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. Pressing the Voice Command button while the system is speaking is known as “barging in.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 To hear the first available Menu, press the Voice Com- 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the Voice Combutton and say “Help” or “Main Menu.” mand mand system is speaking. Please note the volume Commands setting for Voice Command is different than the audio The Voice Command system understands two types of system. commands, Universal commands and Local commands. Universal commands are available at all times.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “Bluetooth Streaming” (to switch to Bluetooth® Radio FM Streaming mode) To switch to the FM band, say “FM” or “Radio FM.” In this mode, you may say the following commands: • “Memo” (to switch to the memo recorder) • “System Setup” (to switch to system setup) • “Frequency #” (to change the frequency) Radio AM • “Next Station” (to select the next station) To switch to the AM band, say “AM” or “Radio AM.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 • “Previous Channel” (to select the previous channel) USB Mode • “List Channel” (to hear a list of available channels) To switch to USB mode, say “USB.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memo Mode – “Previous” (to play the previous memo) To switch to the voice recorder mode, say “Memo.” In this mode, you may say the following commands: – “Delete” (to delete a memo) – “Delete All” (to delete all memos) • “New Memo” (to record a new memo) — During the Setup recording, you may press the Voice Command button to stop recording.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 • “Language French” 2. Repeat the words and phrases when prompted by Uconnect® Voice. For best results, the Voice Training • “Language Spanish” session should be completed when the vehicle is parked, engine running, all windows closed, and the • “Tutorial” blower fan switched off. This procedure may be re• “Voice Training” peated with a new user. The system will adapt to the last trained voice only.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. Power Seats The power seat switches are located on the outboard side of the front seat cushions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Push the switch rearward to decrease the lumbar support. Pushing upward or downward on the switch will The height of the seats can be adjusted up or down. Pull raise and lower the position of the support. upward or push downward on the seat switch, the seat will move in the direction of the switch. Release the switch when the desired position is reached.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 You can choose from HIGH, LOW or OFF heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for HIGH, one for LOW and none for OFF. Press the switch once to select HIGH-level heating. Press the switch a second time to select LOW-level heating. Press the switch a third time to shut the heating elements OFF.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE rearward. Release the bar once the seat is in the desired position. Using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Passenger Seat Easy Entry On the passenger seat, pull forward on the lever located on the side of the seatback in order to dump the seatback and slide the seat forward. You can also temporarily remove the seat belt from the guide loop on the seat and allow the seat belt to retract out of the way. This allows for easier access to the rear seat.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Head Restraints Active Head Restraints — Front Seats Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. The front driver and passenger seats are equipped with Active Head Restraints (AHR).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. NOTE: The head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your authorized dealer.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat The rear seatbacks can be folded forward to provide an additional storage area. Pull on the loops located on the upper part of the rear seatback to fold down either or both seatbacks. These loops can be tucked away when not in use. Folded Rear Seat When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 WARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. • The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Move to the outside of the vehicle and push the safety catch to the left. The safety catch is located under the center front edge of the hood. CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 LIGHTS Headlights And Parking Lights The headlight switch is located on the left side of the instrument panel. This switch controls the operation of the headlights, parking lights, instrument panel lights, instrument panel light dimming, interior lights and fog lights. 3 Headlight Switch Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch counterclockwise to the A (AUTO) position. When the system is on, the headlight time delay feature is also on. This means the headlights will stay on for up to 90 seconds after you place the ignition in the OFF position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 If you turn the headlights off before the ignition, they will DRL function. If equipped, the DRL will flash when a turn signal is in operation, and return to DRL mode when turn off in the normal manner. the turn signal is no longer flashing. NOTE: The lights must be turned off within 45 seconds of placing the ignition in the OFF position to activate this WARNING! feature. The Headlight delay time is programmable.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fog Lights — If Equipped The front fog light switch is built into the headlight switch. To activate the front fog lights, turn on the parking lights or the low beam headlights and press the headlight switch. To turn off the front fog lights, either press the headlight switch again or turn off the headlight switch. Fog Light Operation An indicator light in the instrument cluster illuminates when the fog lights are turned on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Multifunction Lever Turn Signals The multifunction lever controls the operation of the turn Move the multifunction lever up or down and the arrows signals, headlight beam selection and passing lights. The on each side of the instrument cluster flash to show multifunction lever is located on the left side of the proper operation of the front and rear turn signal lights. steering column.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If the multifunction lever is held in the flash-to pass position for more than 15 seconds, the high beams Tap the lever up or down once, without moving beyond will shut off. the detent, and the turn signal (right or left) will flash three times then automatically turn off. Map/Reading Lights Lane Change Assist These lights are mounted between the sun visors on the Push the multifunction lever away from you to switch overhead console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 open. This includes the glove box light, but not the trunk light. To restore interior light operation, either place the ignition in the RUN position or cycle the light switch. Dimmer Control The dimmer control is located to the right of the headlight switch.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Light Defeat (OFF) Rotate the dimmer control to the extreme bottom off position. The interior lights will remain off when the doors are open. Parade Mode (Daytime Brightness Feature) Rotate the dimmer control upward to the first detent. This feature brightens all text displays such as the odometer, Electronic Vehicle Information Center (EVIC), and radio when the parking lights or headlights are on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 CAUTION! Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper switch is left in any position other than off. Mist Feature Rotate the end of the lever downward to the Mist position to activate a single wipe cycle to clear off road mist or spray from a passing vehicle. The wipers will continue to operate until you release the multifunction lever.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you activate the washer while the windshield wiper is position. In addition, the headlights will turn off when turned off, the wipers will operate for three wipe cycles the wipers are turned off if they were turned on by this feature. and then turn off. WARNING! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. HEATED STEERING WHEEL — IF EQUIPPED Tilt/Telescoping Control Handle To unlock the steering column, pull the lever downward.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The heated steering wheel switch is located on the switch — If Equipped” in “Things to Know Before Starting Your bank below the climate controls. There are also soft-keys Vehicle” for further information. in the radio screen that will activate the heated steering wheel. WARNING! Press the switch to turn on the heated steering wheel. The light on the switch will illuminate to indicate the steering wheel heater is on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, the Electronic Speed Control takes over accelerator operations at speeds greater than 25 mph (40 km/h). The Electronic Speed Control buttons are located on the right side of the steering wheel.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 To Deactivate The speed increment shown is dependant on the speed of U.S. (mph) or Metric (km/h) units: A soft tap on the brake pedal, pushing the CANCEL button, or normal brake pressure while slowing the U.S. Speed (mph) vehicle will deactivate the Electronic Speed Control with• Pressing the RES (+) button once will result in a 1 mph out erasing the set speed memory. increase in set speed.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If the button is continually pressed, the set speed will continue to decrease until the button is released, then When the Electronic Speed Control is set, you can dethe new set speed will be established. crease speed by pushing the SET (-) button. The speed decrement shown is dependant on the speed To Accelerate For Passing To Decrease Speed of U.S. (mph) or Metric (km/h) units: U.S. Speed (mph) Press the accelerator as you would normally.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control and have an accident. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense® Warning Display The ParkSense® Warning screen will only be displayed if Sound and Display is selected from the Customer- Programmable Features section of the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (CustomerProgrammable Features)” in “Understanding Your Instrument Panel” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 3 Park Assist System Off The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the obstacle the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fast Tone Continuous Tone The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 Rear Distance (in/cm) Audible Alert Chime Arcs Greater than 59 in (150 cm) None Radio Volume Reduced No None WARNING ALERTS 59-39 in 39-25 in (150-100 cm) (100-65 cm) Single 1/2 Slow Second Tone 3 Solid 3 Slow (Continuous) Flashing Yes Yes NOTE: ParkSense® will reduce the volume of the radio, if on, when the system is sounding an audio tone.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE shift lever is moved to REVERSE and the system is disabled, the EVIC will display the “PARK ASSIST SYSTEM OFF” message for as long as the vehicle is in REVERSE. OFF REAR SENSORS⬙ message for as long as the vehicle is in REVERSE. Under this condition, ParkSense® will not operate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 ParkSense® System Usage Precautions NOTE: • ParkSense®, when on, will MUTE the radio when it is sounding a tone. • Clean the ParkSense® sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not working • Jackhammers, large trucks, and other vibrations could properly.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! • ParkSense® is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using ParkSense® in order to be able to stop in time when an obstacle is detected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 These lights also turn on when a door is opened, when the UNLOCK button on the Remote Keyless Entry (RKE) transmitter is pressed, or when the dimmer control is turned fully upward, past the second detent. Sunglasses Storage At the rear of the console, a compartment is provided for the storage of a pair of sunglasses. The storage compartment access is a ⬙push/push⬙ design. Push on the raised bar on the compartment door to open. Push on the raised bar to close.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink® buttons that are located in the overhead Before You Begin Programming HomeLink® console designate the three different HomeLink® chan- Ensure your vehicle is parked outside of the garage nels. before you begin programming. For efficient programming and accurate transmission of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink® system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 NOTE: • Erasing all channels should only be performed when programming HomeLink® for the first time. Do not erase channels when programming additional buttons. • If you have any problems, or require assistance, please call toll-free 1-800-355-3515 or, on the Internet at www.HomeLink.com for information or assistance. Programming A Rolling Code For programming garage door openers that were manufactured after 1995.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the hand - held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink® button you wish to program. Firmly press and release the “LEARN” or “TRAINING” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the LEARN/TRAIN mode. 3. Simultaneously press and hold both the Homelink® button you want to program and the hand - held transmitter button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 3. Simultaneously press and hold both the Homelink® button you want to program and the hand - held To reprogram a channel that has been previously trained, transmitter button. follow these steps: Reprogramming A Single HomeLink® Button 4. Continue to hold buttons until the EVIC display changes from “CHANNEL # TRAINING” to “CHAN2. Press and hold the desired HomeLink® button until NEL # TRAINED,” then release both buttons.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To program the remaining two HomeLink® buttons, Canadian/Gate Operator Programming repeat each step for each remaining button. DO NOT For programming transmitters in Canada/United States erase the channels. that require the transmitter signals to “time-out” after several seconds of transmission.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 3. Simultaneously press and hold both the Homelink® Reprogramming A Single HomeLink® Button button while you press and release (“cycle”), your To reprogram a channel that has been previously trained, hand - held transmitter every two seconds. follow these steps: 4. Continue to hold buttons until the EVIC display 1. Turn the ignition switch to the ON/RUN position. changes from “CHANNEL # TRAINING” to “CHAN2.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Did you unplug the device for programming and remember to plug it back in? It is advised to erase all channels before you sell or turn in your vehicle. If you have any problems, or require assistance, please To erase the channels press and hold the two outside call toll-free 1-800-355-3515 or, on the Internet at HomeLink® buttons (I and III) for up 20 seconds. The www.HomeLink.com for information or assistance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 WARNING! Your motorized door or gate will open and close while you are programming the universal transceiver. Do not program the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. Power Sunroof Switch WARNING! • Never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the Key Fob in or near the vehicle, or in a location accessible to children. Do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/RUN mode.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 WARNING! (Continued) • Do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or any object, to project through the sunroof opening. Injury may result. movement. The sunroof and sunshade will remain in a partially opened condition until the switch is pushed and held rearward again.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pinch Protect Feature Sunshade Operation This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an obstruction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruction if this occurs. Next, press the switch forward and release to Express Close. The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 Sunroof Maintenance ELECTRICAL POWER OUTLETS Use only a nonabrasive cleaner and a soft cloth to clean There are two 12 Volt (13 Amp) electrical power outlets the glass panel. on this vehicle. Both of the outlets are protected by a fuse. The front 12 Volt power outlet has power available only For Vehicles Not Equipped With The Electronic Vehicle when the ignition is placed in the ACC or RUN position.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 The center console power outlet is powered directly from the battery (power available at all times). 3 Power Outlet Fuse Locations Center Console Power Outlet Items plugged into this power outlet may discharge the battery and/or prevent the engine from starting.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. • Many accessories that can be plugged in draw power from the vehicle’s battery even when not in use (i.e., cellular phones, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 CAUTION! (Continued) • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your warranty. 3 CUPHOLDERS Front Cupholders The front cupholders are located in the center console. Front Cupholders Illuminated Front Cupholders — If Equipped The front cupholders are illuminated with LEDs.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Cupholders The rear seat cupholders are located in the center armrest between the rear seats. The cupholders are positioned forward in the armrest and side-by-side to provide convenient access to beverage cans or bottles while maintaining a resting place for the rear occupant’s elbows.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 CONSOLE FEATURES Console Storage The center console has a storage compartment located underneath the armrest, and also contains a 12 Volt The center console armrest slides forward with three power outlet, a molded-in coin holder (designed to hold detents to provide flexibility for comfort, cupholder use various size coins). The center console may also be and shifting ease. equipped with a Universal Consumer Interface (UCI).
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Defroster Center Console WARNING! Do not operate this vehicle with a console compartment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. The rear window defroster button is located on the climate control (Mode) knob. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 INSTRUMENT PANEL FEATURES . . . . . . . . . .206 ▫ Performance Features . . . . . . . . . . . . . . . . . .227 䡵 INSTRUMENT CLUSTER . . . . . . . . . . . . . . . . .207 ▫ Keyless Enter-N-Go™ Display — If Equipped . .231 䡵 INSTRUMENT CLUSTER DESCRIPTIONS . . . . .208 ▫ Driver-Selectable Surround Sound (DSS) – If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .232 䡵 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) . . . . . . . . . . . . . . . . .
204 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operating Instructions (Voice Command System) — If Equipped . . . . . . . . . . . . . . . . . . . . . . .239 ▫ Operating Instructions (Uconnect® Phone) — If Equipped. . . . . . . . . . . . . . . . . . . . . . . . . .239 䡵 Uconnect® 130 . . . . . . . . . . . . . . . . . . . . . . . . .240 ▫ Operating Instructions — Radio Mode . . . . . .240 ▫ Operation Instructions — CD MODE For CD And MP3 Audio Play . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 205 ▫ List Or Browse Mode . . . . . . . . . . . . . . . . . . .269 䡵 CD/DVD DISC MAINTENANCE . . . . . . . . . . .275 ▫ Bluetooth® Streaming Audio (BTSA) . . . . . . .271 䡵 RADIO OPERATION AND MOBILE PHONES . .276 䡵 HARMAN KARDON® Logic7® HIGH 䡵 CLIMATE CONTROLS . . . . . . . . . . . . . . . . . . .276 PERFORMANCE MULTICHANNEL SURROUND ▫ Automatic Temperature Control (ATC) . . . . . .276 SOUND SYSTEM WITH DRIVER-SELECTABLE SURROUND (DSS) — IF EQUIPPED . . . . . . . . .
206 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 2 3 4 5 — Air Outlets — Instrument Cluster — Glove Compartment — Radio — Heated Seat Switch 6 — ESC OFF Switch 7 — Sport Button 8 — Hazard Warning Switch 9 — Heated Steering Wheel Switch 10 — Climate Control 11 — Ignition Switch 12 — Trunk Release Button 13 — Headlight Switch
UNDERSTANDING YOUR INSTRUMENT PANEL 207 INSTRUMENT CLUSTER 4
208 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position. 4. Electronic Speed Control Indicator Light This light will turn on when the electronic speed control is on. 2. Trip Odometer Button 5. Tachometer Press this button to change the display from odometer to either of two trip odometer settings. The letter “A” or “B” will appear when in the trip odometer mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 charging system is experiencing a problem. See your If the light is flashing when the engine is running, immediate service is required. In this case, you may local authorized dealer to obtain service immediately. If jump starting is required, refer to “Jump Starting experience reduced performance, an elevated/rough idle or engine stall, and your vehicle may require towing. Procedures” in “What To Do In Emergencies”. 7.
210 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “260“, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “260”, and you hear continuous chimes, turn the engine off immediately and call an authorized dealer for service. WARNING! A hot engine cooling system is dangerous.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 engine running. If the “ESC Activation/Malfunction Indicator Light” comes on continuously with the engine running, a malfunction has been detected in the ESC system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles 11.
212 UNDERSTANDING YOUR INSTRUMENT PANEL • The ESC system will make buzzing or clicking The engine oil level must be checked under the hood. sounds when it is active. This is normal; the sounds 15. High Beam Indicator will stop when ESC becomes inactive following the This indicator will turn on when the high beam maneuver that caused the ESC activation. headlights are on. Push the multifunction lever 13.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 17. Shift Lever Indicator — Automatic Transmission NOTE: U.S. Federal regulations require that upon transOnly fer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been The Shift Lever Indicator is self-contained within the driven. If your odometer needs to be repaired or serviced, instrument cluster. It displays the gear position of the the repair technician should leave the odometer reading automatic transmission.
214 UNDERSTANDING YOUR INSTRUMENT PANEL 20. Brake Warning Light The light will remain on until the cause is corrected. This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 Operation of the Brake Warning Light can be checked by 22. Tire Pressure Monitoring Telltale Light turning the ignition switch from the OFF position to the Each tire, including the spare (if provided), ON/RUN position. The light should illuminate for apshould be checked monthly when cold and inproximately two seconds.
216 UNDERSTANDING YOUR INSTRUMENT PANEL Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 23. Anti-Lock Brake (ABS) Light 24. Low Fuel Light This light will turn on and a single chime will This light monitors the Anti-Lock Brake System sound when the fuel level drops to 1/8 tank. (ABS). The light will turn on when the ignition switch is placed in the ON/RUN position and 25. Malfunction Indicator Light (MIL) may stay on for as long as four seconds.
218 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the instrument cluster.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel.
220 UNDERSTANDING YOUR INSTRUMENT PANEL The system allows the driver to select information by press- UP Button ing the following buttons mounted on the steering wheel: Press and release the UP button to scroll upward through the main menus and sub-menus. DOWN Button Press and release the DOWN button to scroll downward through the main menus and sub-menus. EVIC Steering Wheel Buttons MENU Button Press and release the MENU button to access the main menu, or to return to the main menu from the sub-menus.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 Electronic Vehicle Information Center (EVIC) Displays • Door(s) Ajar (with a single chime if vehicle is in motion) When the appropriate conditions exist, the EVIC displays • the following messages: • • Turn Signal On (with a continuous warning chime if the vehicle is driven more than 1 mile [1.
222 UNDERSTANDING YOUR INSTRUMENT PANEL • Tire Pressure Display Screen With Low Tire(s) “Inflate • Tire to XX” • • ESC Off – Electronic Stability Control is deactivated • • Check Gascap • • Key Fob Battery Low • • Service Keyless System • • Wrong Key • • Damaged Key • • Key not Programmed • • Push Button or Insert Key/Turn To Run (refer to • “Remote Starting System” in “Things To Know Before Starting Your Vehicle”) • • 1–4 SKIPSHIFT • UPSHIFT Sport Mode Active 0-60 mph (0-100 km/h) Braking Distance 1/8 Mi
UNDERSTANDING YOUR INSTRUMENT PANEL 223 Gear Shift Indicator (GSI) — If Equipped The Gear Shift Indicator (GSI) system is enabled on vehicles with a manual transmission, or when a vehicle with an automatic transmission is in manual shift mode. The GSI provides the driver with a visual indication within the EVIC when the recommended gear shift point has been reached. This indication notifies the driver that changing gear will allow a reduction in fuel consumption.
224 UNDERSTANDING YOUR INSTRUMENT PANEL When the shift down indicator (-) is shown on the display, Engine Oil Change Indicator System the GSI is advising the driver to engage a lower gear. Oil Change Required Your vehicle is equipped with an engine oil change indicator system. The “Oil Change Required” message will flash in the EVIC display for approximately 10 seconds after a single chime has sounded, to indicate the next scheduled oil change interval.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 Vehicles Equipped With Keyless Enter-N-Go™ Trip Functions 1. Without pressing the brake pedal, cycle the ignition to To access, press and release the MENU button until “Trip Functions” appears in the EVIC, then press and release the ON/RUN position (Do not start the engine.) the SELECT button. 2. Fully depress the accelerator pedal, slowly, three times The Trip Functions include the following: within 10 seconds. 3. Cycle the ignition to the OFF/LOCK position.
226 UNDERSTANDING YOUR INSTRUMENT PANEL The Trip Functions mode displays the following. When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change Average Fuel Economy to a text display of ⬙LOW FUEL.⬙ This display will Shows the average fuel economy since the last reset. When continue until the vehicle runs out of fuel.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 Display Units Of Measure In To make your selection, press and release the SELECT button until “ENGLISH” or “METRIC” appears. To Reset The Display Reset will only occur while a resettable function is being displayed. Press and release the SELECT button once to clear the resettable function being displayed. To reset all resettable functions, press and release the SELECT button a second time within three seconds of resetting the currently-displayed function.
228 UNDERSTANDING YOUR INSTRUMENT PANEL This mode provides performance based suspension tuning with improved handling and acceleration through an electronic controlled dampening system. This system reduces body roll and pitch in many driving situations including cornering, acceleration and braking.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 • Pressing the SELECT button will clear the current run • The distance measurement will be aborted if the brake pedal is released before the vehicle comes to a comtime and display the vehicle’s best 0-60 mph plete stop. (0-100 km/h) time. • To clear the vehicle’s best 0-60 mph (0-100 km/h) time, • The distance and speed measurements will continue to display until the SELECT button is pressed. press and hold the SELECT button for five seconds.
230 UNDERSTANDING YOUR INSTRUMENT PANEL • Dashes will display if the vehicle fails to reach 1/8 • When a force greater than zero is measured, the display will update the value as it climbs. As the mile (1/4 mile) in less then 30 seconds. G-Force falls, the peak forces will continue to display. • The time and speed will continue to display until the • Pressing the SELECT button will clear the peak force SELECT button is pressed. values.
UNDERSTANDING YOUR INSTRUMENT PANEL 231 Launch RPM Set (Manual Transmission Only) When selected, this screen displays the vehicle’s current Launch RPM used for Launch Control (refer to “ESC Operating Modes – Launch Control” in “Starting and Operating”). Keyless Enter-N-Go™ Display — If Equipped When the ENGINE START/STOP button is pressed to change ignition switch positions, the Keyless Enter-NGo™ icon momentarily appears in the EVIC display showing the new ignition switch position.
232 UNDERSTANDING YOUR INSTRUMENT PANEL The round symbol in the middle rotates to point at the new ignition switch position. If desired, the ignition switch position graphic can be set to be constantly visible by pressing the EVIC MENU button until the display appears. • Stereo • Surround Sound While in the Surround Sound menu, press the SELECT button to change surround modes. Refer to “Keyless Enter-N-Go™” in “Starting And Oper- Compass Display ating” for more information.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 Automatic Compass Calibration 3. Press the UP or DOWN button until “CALIBRATE COMPASS” displays in the EVIC. This compass is self-calibrating, which eliminates the need to set the compass manually. When the vehicle is 4. Press and release the SELECT button to start the new, the compass may appear erratic and the EVIC will calibration. The message “CAL” will display in the display “CAL” until the compass is calibrated. You may EVIC.
234 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Keep magnetic materials away from the top of the 1. Turn the ignition switch ON. instrument panel, such as iPod’s, Mobile Phones, Lap2. Press and release the MENU button until Personal tops and Radar Detectors. This is where the compass Settings displays in the EVIC. module is located, and it can cause interference with the compass sensor, and it may give false readings. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 235 • Oil Temperature Language Shows the actual oil temperature. When in this display, you may select one of three languages for all display nomenclature, including the trip functions and the Uconnect® gps (if equipped). Press the SELECT button while in this display to select English, Espanol, or Francais. Then, as you continue, the information will display in the selected language. • Oil Pressure Shows the actual oil pressure.
236 UNDERSTANDING YOUR INSTRUMENT PANEL remote start or until the key is turned to RUN. To make your selection, press and release the SELECT button until When Driver Door 1st Press is selected, only the driver’s a check-mark appears next to the feature showing the door will unlock on the first press of the Remote Keyless system has been activated or the check-mark is removed Entry (RKE) transmitter UNLOCK button. When Driver showing the system has been deactivated.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 Headlamps On with Wipers (Available with Auto Headlights Only) When ON is selected, and the headlight switch is in the AUTO (A) position, the headlights will turn on approximately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on by this feature. To make your selection, press and release the SELECT button until “ON” or “OFF” appears. when exiting the vehicle.
238 UNDERSTANDING YOUR INSTRUMENT PANEL Delay Power Off To Accessories Until Exit Keyless Enter-N-Go™ (Passive Entry) When this feature is selected, the power window switches, radio, Uconnect® phone (if equipped), power sunroof (if equipped), and ignition-powered power outlets will remain active for up to 60 minutes after the ignition switch is turned OFF. Opening either front vehicle door will cancel this feature. To make your selection, press and release the SELECT button until “Off,” “45 sec.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 is removed showing the system has been deactivated. Refer to “Rear Park Assist System” in “Understanding The Features Of Your Vehicle” for system function and operating information. Uconnect® 730N/430/430N CD/DVD/HDD/NAV — IF EQUIPPED Refer to your Uconnect® 730N, 430 or 430N user’s manual for detailed operating instructions.
240 UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) Uconnect® 130 Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction, without stopping. Turning the ON/VOLUME control knob to the right increases the volume, and to the left decreases it.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 another selection. Holding either button will bypass 5. To exit, press any button/knob, or wait five seconds. stations without stopping, until you release it. RW/FF TIME Button Pressing the RW (Rewind) or FF (Fast Forward) buttons Press the TIME button to alternate display of the time causes the tuner to search for the next frequency in the and radio frequency. direction of the arrows. This feature operates in either AM or FM frequencies.
242 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the AM/FM Button mid-range tones. Press the buttons to select either AM or FM mode. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice. Operation Instructions — CD MODE For CD And MP3 Audio Play NOTE: • The ignition switch must be in the ON or ACC position to operate the radio.
244 UNDERSTANDING YOUR INSTRUMENT PANEL If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. CAUTION! (Continued) • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 SEEK Button AM/FM Button Press the right SEEK button for the next selection on the CD. Press the left SEEK button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD and MP3 modes. Press the button to select either AM or FM mode.
246 UNDERSTANDING YOUR INSTRUMENT PANEL Supported Media (Disc Types) The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. Supported Medium Formats (File Systems) the file name and folder name, and will assign a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. MPEG Specification MPEG-1 Audio Layer 3 Sampling Frequency (kHz) 48, 44.
248 UNDERSTANDING YOUR INSTRUMENT PANEL Playback Of MP3 Files Operation Instructions — Auxiliary Mode When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 Uconnect® 130 WITH SATELLITE RADIO Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction, without stopping. Turning the ON/VOLUME control knob to the right increases the volume, and to the left decreases it.
250 UNDERSTANDING YOUR INSTRUMENT PANEL another selection. Holding either button will bypass Clock Setting Procedure stations without stopping, until you release it. 1. Press and hold the TIME button until the hours blink. Voice Command System (Radio) — If Equipped 2. Adjust the hours by turning the right side TUNE/ Refer to “Voice Command” for further details. SCROLL control knob. Voice Command Button Uconnect® Phone — If Equipped 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 step 2. For vehicles not equipped with satellite radio, press Setting The Tone, Balance And Fade the SETUP button and then follow the above procedure, Push the rotary TUNE/SCROLL control knob and BASS starting at step 2. will display. Turn the TUNE/SCROLL control knob to INFO Button the right or left to increase or decrease the bass tones. Press the INFO button for an RDS station (one with call Push the rotary TUNE/SCROLL control knob a second letters displayed).
252 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary TUNE/SCROLL control knob again to exit setting tone, balance, and fade. MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 Program Type Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 16-Digit Character Display Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R&B Sports Talk Top 40 Weather station with the same selected Music Type name. The Music Type function only operates when in the FM mode.
254 UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button Press the button to select either AM or FM mode. SET/RND Button — To Set The Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND button. The symbol SET 1 will now show in the display window. Select the button (1–6) you wish to lock onto this station and press and release that button.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will NOTE: show the track number, and index time in minutes and • The ignition switch must be in the ON/RUN or ACC seconds. Play will begin at the start of track 1. position to operate the radio.
256 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! (Continued) • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player. EJECT Button — Ejecting A CD Press the EJECT button to eject the CD. SEEK Button Press the right SEEK button for the next selection on the CD.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 AM/FM Button Supported Media (Disc Types) Press the button to select either AM or FM mode. The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. SET/RND Button (Random Play Button) Supported Medium Formats (File Systems) Press this button while the CD is playing to activate Random Play.
258 UNDERSTANDING YOUR INSTRUMENT PANEL the file name and folder name, and will assign a number Supported MP3 File Formats instead. With a maximum number of files, exceeding 20 The radio will recognize only files with the *.MP3 extenfolders will result in this display. With 200 files, exceedsion as MP3 files. Non-MP3 files named with the *.MP3 ing 50 folders will result in this display.) extension may cause playback problems.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 MPEG Specification MPEG-1 Audio Layer 3 Sampling Frequency (kHz) 48, 44.1, 32 MPEG-2 Audio Layer 3 24, 22.05, 16 Bit Rate (kbps) 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 Playback Of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium.
260 UNDERSTANDING YOUR INSTRUMENT PANEL To increase the speed of disc loading, it is recommended Press the INFO button once more to return to ⬙elapsed to use CD-R media and single-session discs. To create a time⬙ priority mode. single-session disc, enable the “Disc at Once” option Press and hold the INFO button for three seconds or before writing to the disc. more and the radio will display song titles for each file.
UNDERSTANDING YOUR INSTRUMENT PANEL 261 NOTE: The AUX device must be turned on and the device’s sports, news, entertainment, and programming for chilvolume set to the proper level. If the AUX audio is not loud dren, directly from its satellites and broadcasting studios. enough, turn the device’s volume up. If the AUX audio NOTE: Sirius service is not available in Hawaii and has sounds distorted, turn the device’s volume down. limited coverage in Alaska.
262 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Serial Number/Sirius Identification Number (ESN/SID) Selecting Uconnect® Multimedia (Satellite) Mode Press the SAT button until ⬙SAT⬙ appears in the display. A Please have the following information available when CD may remain in the radio while in the Satellite radio calling: mode. 1. The Electronic Serial Number/Sirius Identification Satellite Antenna Number (ESN/SID).
UNDERSTANDING YOUR INSTRUMENT PANEL 263 • Dense tree coverage may interrupt reception in the remain tuned to the new channel until you make another selection. Holding either button will bypass channels form of short audio mutes. without stopping until you release it. • Driving under wide bridges or along tall buildings can SCAN Button cause intermittent reception.
264 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the Music Type function is active, the radio will be tuned to the next Pressing the RW (Rewind) or FF (Fast Forward) buttons channel with the same selected Music Type name. causes the tuner to search for the next channel in the direction of the arrows. If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be TUNE Control (Rotary) exited and the radio will tune to the preset channel.
UNDERSTANDING YOUR INSTRUMENT PANEL 265 SET Button — To Set The Pushbutton Memory When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button. If a button is not selected within five seconds after pressing the SET button, the channel will continue to play but will not be stored into pushbutton memory.
266 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • If the radio has a USB port, refer to the appropriate Uconnect® Multimedia radio User’s Manual for iPod® or external USB device support capability. • Connecting an iPod® or consumer electronic audio device to the AUX port located in the radio faceplate, plays media, but does not use the iPod® /MP3 control feature to control the connected device.
UNDERSTANDING YOUR INSTRUMENT PANEL 267 NOTE: The center console will have a position where the iPod® or consumer electronic audio device cable can be routed through without damaging the cable when closing the lid. A factory cut out space for the cable to be routed may be located in the base of the center console on either the front or side. This allows routing of the cable without damaging it while closing the lid.
268 UNDERSTANDING YOUR INSTRUMENT PANEL Controlling The iPod® Or External USB Device Using Radio Buttons • Turning it clockwise (forward) by one click, while playing a track, skips to the next track or press the VR button and say ⬙Next Track.
UNDERSTANDING YOUR INSTRUMENT PANEL 269 during play mode will jump to the next track in the list, or press the VR button and say ⬙Next or Previous Track.⬙ SCAN button again. During Scan mode, pressing the << SEEK and SEEK >> buttons will select the previous and next tracks. • While a track is playing, press the INFO button to see • RND button (available on sales code RES radio only): the associated metadata (artist, track title, album, etc.
270 UNDERSTANDING YOUR INSTRUMENT PANEL • Turning it clockwise (forward) and counterclockwise (backward) scrolls through the lists, displaying the track detail on the radio display. Once the track to be played is highlighted on the radio display, press the TUNE control knob to select and start playing the track. Turning the TUNE control knob fast will scroll through the list faster. During fast scroll, a slight delay in updating the information on the radio display may be noticeable.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 device, then follow the same steps to go to the desired track in that list. Not all iPod® or external USB device sub-menu levels are available on this system. WARNING! Do not plug in or remove the iPod® or external USB device while driving. Failure to follow this warning could result in an accident. • MUSIC TYPE button: The MUSIC TYPE button is another shortcut button to the genre listing on your audio device.
272 UNDERSTANDING YOUR INSTRUMENT PANEL device first, then it will get streamed to the Uconnect® phone system. Seven devices can be paired to the Uconnect® phone system, but just one can be selected and played. Previous Track Selecting A Different Audio Device Browse Use the SEEK DOWN button, or press the VR button on the radio and say “Previous Track,” to jump to the previous music track on your cellular phone. 1. Press the PHONE button to begin.
UNDERSTANDING YOUR INSTRUMENT PANEL 273 proprietary amplifier and speaker technologies deliver- AUX input; and is activated through Uconnect® radio ing substantial increases in component and system effi- touchscreen. Refer to “Customer Programmable Features” under “Uconnect® SETTINGS” in “Understandciency levels. ing Your Instrument Panel”.
274 UNDERSTANDING YOUR INSTRUMENT PANEL The right-hand control is a rocker-type switch with a push-button in the center and controls the volume and The remote sound system controls are located on the rear mode of the sound system. Pressing the top of the rocker surface of the steering wheel. Reach behind the wheel to switch will increase the volume, and pressing the bottom of the rocker switch will decrease the volume. access the switches.
UNDERSTANDING YOUR INSTRUMENT PANEL 275 The button located in the center of the left-hand control CD/DVD DISC MAINTENANCE will tune to the next preset station that you have pro- To keep a CD/DVD in good condition, take the following grammed in the radio preset pushbutton. precautions: CD Player 1. Handle the disc by its edge; avoid touching the Pressing the top of the switch once will go to the next surface. track on the CD. Pressing the bottom of the switch once 2.
276 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particular disc, it may be damaged (e.g., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service.
UNDERSTANDING YOUR INSTRUMENT PANEL 277 You will experience the greatest efficiency by simply allowing the system to function automatically. Selecting Operation of the system is quite simple. the “O” (OFF) position on the blower control stops the Turn the Mode Control knob (right knob) and the Blower system completely and closes the outside air intake. Control knob (left knob) to AUTO.
278 UNDERSTANDING YOUR INSTRUMENT PANEL • If your air conditioning performance seems lower than expected, check the front of the A/C condenser located in front of the radiator for an accumulation of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser. Fabric front fascia protectors may reduce airflow to the condenser, reducing air conditioning performance.
UNDERSTANDING YOUR INSTRUMENT PANEL 279 4
280 UNDERSTANDING YOUR INSTRUMENT PANEL The operator can override the AUTO mode setting to • Floor change airflow distribution by rotating the Mode Control Air is directed through the floor outlets with a knob (right knob) to one of the following positions. small amount flowing through the defrost and • Panel side window demist outlets. Air is directed through the outlets in the instru- • Mix ment panel. These outlets can be adjusted to direct Air is directed through the floor, defrost, and side airflow.
UNDERSTANDING YOUR INSTRUMENT PANEL 281 • Air Conditioner Control NOTE: Press this button to turn on the air • When the ignition switch is turned to the LOCK position, the recirculation feature will be cancelled. conditioning during manual operation only. When the air conditioning is • In cold weather, use of the Recirculation mode may turned on, cool dehumidified air will lead to excessive window fogging.
282 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Vacation Storage NOTE: Refer to the chart at the end of this section for Anytime you store your vehicle, or keep it out of service suggested control settings for various weather conditions. (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the Summer Operation fresh air and high blower settings.
UNDERSTANDING YOUR INSTRUMENT PANEL 283 Side Window Demisters A/C Air Filter A side window demister outlet is located at each end of the instrument panel. These non-adjustable outlets direct air toward the side windows when the system is in the FLOOR, MIX, or DEFROST mode. The air is directed at the area of the windows through which you view the outside mirrors. The A/C Filter prevents most dust and pollen from entering the cabin.
284 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions For Various Weather Conditions While In Manual Override
STARTING AND OPERATING CONTENTS 䡵 STARTING PROCEDURES . . . . . . . . . . . . . . . .289 䡵 MANUAL TRANSMISSION — IF EQUIPPED . .298 ▫ Manual Transmission — If Equipped . . . . . . . .289 ▫ Six-Speed Manual Transmission . . . . . . . . . . .298 ▫ Automatic Transmission — If Equipped . . . . .290 䡵 AUTOMATIC TRANSMISSION — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . ▫ Keyless Enter-N-Go™ — If Equipped . . . . . . .291 ▫ Key Ignition Park Interlock. . . . . . . . . . . . ▫ Normal Starting. . . .
286 STARTING AND OPERATING ▫ Steering Wheel Mounted Paddle Shifters Or Console Mounted Shifter . . . . . . . . . . . . . . . .311 䡵 SPORT MODE . . . . . . . . . . . . . . . . . . . . . . . . .313 䡵 LAUNCH MODE — IF EQUIPPED . . . . . . . . . .315 䡵 DRIVING ON SLIPPERY SURFACES . . . . . . . . .319 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . .319 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . .320 䡵 DRIVING THROUGH WATER . . . . . . . . . . . . .
STARTING AND OPERATING 287 䡵 TIRE SAFETY INFORMATION . . . . . . . . . . . . .340 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . .356 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . .340 ▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . .357 ▫ Tire Identification Number (TIN). . . . . . . . . . .343 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . .358 ▫ Tire Terminology And Definitions . . . . . . . . . .345 䡵 TIRE CHAINS (TRACTION DEVICES) . . . . .
288 STARTING AND OPERATING ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . .370 䡵 VEHICLE LOADING . . . . . . . . . . . . . . . . . . . .377 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . .371 ▫ Vehicle Certification Label . . . . . . . . . . . . . . .377 ▫ E-85 Usage In Non-Flex Fuel Vehicles . . . . . . .371 ▫ Gross Vehicle Weight Rating (GVWR) . . . . . . .377 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . .372 ▫ Gross Axle Weight Rating (GAWR) . . . . . . . . .
STARTING AND OPERATING 289 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! • When leaving the vehicle, always remove the Key Fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle.
290 STARTING AND OPERATING Press the clutch pedal fully to the floor, and turn the ignition switch to the START position and release when the engine starts. If the engine fails to start within 15 seconds, turn the ignition switch to the OFF position, wait 10 to 15 seconds, then repeat the “Normal Starting” procedure. WARNING! Do not attempt to push or tow your vehicle to get it started.
STARTING AND OPERATING 291 Using Fob With Integrated Key (Tip Start) NOTE: Normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal. Keyless Enter-N-Go™ — If Equipped This feature allows the driver to operate the ignition switch with the push of a button, as long as the ENGINE START/STOP button is installed and the Remote Start/Keyless Enter-NGo™ Key Fob is in the passenger compartment. Do not press the accelerator.
292 STARTING AND OPERATING 3. Press firmly on the center of the button to secure it into 2. Press and hold the brake pedal while pressing the ENGINE START/STOP button once. position. 3. The system takes over and attempts to start the vehicle. If the vehicle fails to start, the starter will 1. The ENGINE START/STOP button can be removed disengage automatically after 10 seconds. from the ignition switch for key fob use. 4. If you wish to stop the cranking of the engine prior to 2.
STARTING AND OPERATING 293 2. Release the button when the engine starts. If the 3. If the shift lever is not in PARK, the ENGINE START/ STOP button must be held for two seconds and vehicle vehicle fails to start within 15 seconds, release the speed must be above 5 mph (8 km/h) before the button, wait 10 to 15 seconds, then repeat the “Normal engine will shut off. The ignition switch position will Starting” procedure. remain in the ACC position until the shift lever is in 3.
294 STARTING AND OPERATING • If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds before the engine will shut off. The ignition 1. With the vehicle stopped, place the shift lever in switch position will remain in the ACC position until NEUTRAL, then press and release the ENGINE the vehicle is stopped and the button is pressed twice START/STOP button. to the OFF position. 2. The ignition switch will return to the OFF position.
STARTING AND OPERATING 295 2. Press the ENGINE START/STOP button once to If Engine Fails To Start change the ignition switch to the ACC position (EVIC displays “IGNITION MODE ACCESSORY”), WARNING! 3. Press the ENGINE START/STOP button a second time to change the ignition switch to the RUN position (EVIC displays “IGNITION MODE RUN”), 4. Press the ENGINE START/STOP button a third time to return the ignition switch to the OFF position (EVIC displays “IGNITION MODE OFF”).
296 STARTING AND OPERATING WARNING! (Continued) • If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly. Refer to “Jump Starting” in “What To Do In Emergencies” for further information. disengage. Once this occurs, release the accelerator pedal and the brake pedal, wait 10 to 15 seconds, then repeat the “Normal Starting” procedure.
STARTING AND OPERATING 297 Clearing A Flooded Engine (Using Fob With Integrated Key) If the engine fails to start after you have followed the “Normal Starting” or “Extreme Cold Weather” procedures, it may be flooded. To clear any excess fuel: After Starting The idle speed is controlled automatically and it will decrease as the engine warms up. ENGINE BLOCK HEATER — IF EQUIPPED 1. Press the accelerator pedal all the way to the floor and The engine block heater warms the engine, and permits hold it.
298 STARTING AND OPERATING WARNING! CAUTION! Remember to disconnect the engine block heater cord before driving. Damage to the 110-115 Volt electrical cord could cause electrocution. • Never drive with your foot resting on the clutch pedal, or try to hold the vehicle on a hill with the clutch pedal partially engaged, as this will cause abnormal wear on the clutch. Refer to “Electronic Brake Control System/Hill Start Assist” in “Starting And Operating” for further information.
STARTING AND OPERATING 299 NOTE: During cold weather, you may experience in- Shifting creased effort in shifting until the transmission fluid Fully press the clutch pedal and lift your foot off the warms up. This is normal. accelerator pedal before shifting gears. As you release the clutch pedal, lightly press the accelerator pedal. Damage to the transmission or clutch may occur if you do not fully press the clutch pedal and lift off of the accelerator pedal when shifting.
300 STARTING AND OPERATING CAUTION! Earlier upshifts during cruise conditions (relatively steady speeds) may result in increased fuel economy. Always make sure the vehicle comes to a complete stop before shifting into REVERSE. Failure to do so may result in transmission damage. Higher upshift speeds may be used to obtain a desired acceleration rate. 1–4 Skip Shift You must always use first gear (or Reverse) when starting There are times when you must shift the transmission from a standing position.
STARTING AND OPERATING 301 first gear to fourth gear. After you shift the transmission to fourth gear, you can press the clutch in and shift to another forward gear. Downshifting To maintain a safe speed and prolong brake life, downshift to maintain a safe speed when descending a steep grade. WARNING! Skipping more than one gear while downshifting, could cause you to lose control of your vehicle. You could have a collision.
302 STARTING AND OPERATING CAUTION! (Continued) WARNING! • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift between PARK, REVERSE, NEUTRAL, or DRIVE when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly pressing the brake pedal. • Unintended movement of a vehicle could injure those in or near the vehicle.
STARTING AND OPERATING 303 WARNING! (Continued) WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.
304 STARTING AND OPERATING vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few This vehicle is equipped with a Brake Transmission Shift hundred miles (kilometers). Interlock system (BTSI) that holds the shift lever in PARK unless the brakes are applied. To shift the transmission Only shift from DRIVE to PARK or REVERSE when the out of PARK, the ignition switch must be turned to the accelerator pedal is released and the vehicle is stopped.
STARTING AND OPERATING 305 NOTE: • After selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. • If there is a need to restart the engine, be sure to cycle the ignition to the OFF position before restarting. Transmission gear engagement may be delayed after restarting the engine if the ignition is not cycled to the OFF position first.
306 STARTING AND OPERATING When parking on a level surface, you may shift the transmission into PARK first, and then apply the parking brake. When parking on a hill, apply the parking brake before shifting the transmission to PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of PARK. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.
STARTING AND OPERATING 307 WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, turn the engine off, and remove the key fob.
308 STARTING AND OPERATING CAUTION! • Before moving the shift lever out of PARK, you must turn the ignition switch from the LOCK/OFF position to the ON/RUN position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • DO NOT race the engine when shifting from PARK or NEUTRAL into another gear range, as this can damage the drivetrain.
STARTING AND OPERATING 309 CAUTION! Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage. Refer to “Recreational Towing” in “Starting And Operating” and “Towing A Disabled Vehicle” in “What To Do In Emergencies” for further information.
310 STARTING AND OPERATING result in transmission damage, Transmission Limp Home Mode is activated. In this mode, the transmission remains in the current gear until the vehicle is brought to a stop. After the vehicle has stopped, the transmission will remain in second gear regardless of which forward gear is selected. PARK, REVERSE, and NEUTRAL will continue to operate. The Malfunction Indicator Light (MIL) may be illuminated.
STARTING AND OPERATING 311 • Vehicle speed is sufficiently high. • The driver is not heavily pressing the accelerator. AUTOSTICK® Steering Wheel Mounted Paddle Shifters Or Console Mounted Shifter AutoStick® is a driver-interactive transmission feature providing manual shift control, giving you more control of the vehicle. AutoStick® allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance.
312 STARTING AND OPERATING DRIVE position, or tap one of the steering wheel- • If AutoStick® is engaged while in SPORT mode, the transmission will remain in the selected gear even mounted shift paddles (+/-). Tapping (-) to enter when maximum engine speed is reached. The transAutoStick® mode will downshift the transmission to the mission will upshift only when commanded by the next lower gear, while using (+) to enter AutoStick® driver.
STARTING AND OPERATING 313 • The system will ignore attempts to upshift at too low SPORT MODE of a vehicle speed. This vehicle is equipped with an electronic controlled • Avoid using speed control when AutoStick® is en- damping system. This system reduces body roll and pitch in many driving situations including cornering, acceleragaged. tion and braking. In addition, the driver has the ability to • Transmission shifting will be more noticeable when select a more aggressive shifting pattern.
314 STARTING AND OPERATING less aggressive shifting. The system will return to OFF when the ignition switch is cycled from RUN to OFF to RUN, if this mode is selected. • SPORT Mode — This mode is selected by the first press of the “SPORT” button. A “SPORT” message will display in the instrument cluster. The system will return to SPORT mode when the ignition switch is cycled from RUN to OFF to RUN, if this mode is selected.
STARTING AND OPERATING 315 shifter or paddle shifters). A “TRACK” message will display in the instrument cluster. The system will return to SPORT mode when the ignition switch is cycled from RUN to OFF to RUN, if this mode is selected. NOTE: For manual transmission vehicles, the available driving modes are SPORT on or SPORT Off. TRACK is not available.
316 STARTING AND OPERATING 6. While holding the brake, rapidly apply the accelerator pedal to wide open throttle. The engine speed will Launch Control is only available when the following hold at approximately 1825 RPM for the quickest procedure is followed: launch. 1. Press the “ESC OFF” button to put the vehicle into • Messages will appear in the cluster EVIC display to ESC Partial mode. The “ESC OFF” lamp will illumiinform the driver if one or more of the above nate in the cluster.
STARTING AND OPERATING 317 Control again from this state will require pressing the Manual Transmission (If Equipped): “ESC OFF” button twice. Repeat steps 3 through 8. Vehicles with a manual transmission have an adjustable Launch control will abort before launch completion and launch RPM controlled through the EVIC Performance display “Launch Aborted” in the cluster under any the Features. Set the desired launch rpm before entering following conditions: launch control.
318 STARTING AND OPERATING Launch control will be active until the vehicle reaches 62 mph (100 kph), at which point the ESC system 5. Fully depress the clutch pedal and make sure the continues in ESC Partial mode. Activating Launch Convehicle is in first gear. trol again from this state will require pressing the “ESC 6. While holding the clutch depressed, rapidly apply the OFF” button once. Repeat steps 3 through 8. accelerator pedal to wide open throttle.
STARTING AND OPERATING 319 CAUTION! Do not attempt to shift when the drive wheels are spinning and do not have traction. Damage to the transmission may occur. • The newly chosen launch rpm will then be displayed. When Launch Control is activated, the engine speed will hold at the newly chosen launch rpm. NOTE: Launch mode is not available within the first 500 miles of engine break-in.
320 STARTING AND OPERATING WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the rear wheels. You could lose control of the vehicle and possibly have a collision. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet mud, loose sand, etc.). Traction 2. Slow down if the road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5.
STARTING AND OPERATING 321 CAUTION! WARNING! (Continued) • Due to lower ground clearance, driving your vehicle up steep driveways, approach ramps or near parking blocks may cause damage to the front fascia and ground effects. • Driving through snow more than 4 inches (100 mm) deep may cause damage to the front fascia and ground effects. water. Furthermore, flowing and/or rising water can carry your vehicle away swiftly.
322 STARTING AND OPERATING WARNING! (Continued) CAUTION! (Continued) • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes. • Failure to follow these warnings may result in injuries that are serious or fatal to you, your passengers, and others around you.
STARTING AND OPERATING 323 CAUTION! (Continued) • Getting water inside your vehicle’s engine can cause it to lock up and stall out, and cause serious internal damage to the engine. Such damage is not covered by the New Vehicle Limited Warranty. NOTE: • Increased noise levels at the end of the steering wheel travel are considered normal and do not indicate that there is a problem with the power steering system.
324 STARTING AND OPERATING Power Steering Fluid Check Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer. CAUTION! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components.
STARTING AND OPERATING 325 NOTE: This system may take some time to return to full • This light only shows that the parking brake is applied. It does not show the degree of brake application. functionality after a battery disconnect. PARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied and place the shift lever in the PARK or REVERSE (manual transmission only) position.
326 STARTING AND OPERATING Manual Transmission — If Equipped Automatic Transmission — If Equipped The foot operated parking brake is positioned below the The foot operated parking brake is located below the lower lower left corner of the instrument panel. To release the left corner of the instrument panel. To apply the park brake, firmly push the park brake pedal fully. To release the parking brake, pull the parking brake release handle.
STARTING AND OPERATING 327 WARNING! WARNING! (Continued) • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • When leaving the vehicle, always remove the Key Fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons.
328 STARTING AND OPERATING CAUTION! If the “Brake Warning Light” remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. In the event power assist is lost for any reason (for example, repeated brake applications with the engine OFF) the brakes will still function. The effort required to brake the vehicle will be much greater than that required with the power system operating.
STARTING AND OPERATING 329 is working properly. This self check occurs each time the These are all normal characteristics of ABS. vehicle is started and accelerated past 7 mph (11 km/h). ABS is activated during braking under certain road or stopping conditions. ABS-inducing conditions can include ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops.
330 STARTING AND OPERATING WARNING! (Continued) • The Anti-Lock Brake System (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The Anti-Lock Brake System (ABS) cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.
STARTING AND OPERATING 331 If both the “Brake Warning Light” and the “ABS Warning Light” remain on, the ABS and EBD systems are not functioning. Immediate repair to the ABS system is required. Anti-Lock Brake System (ABS) This system aids the driver in maintaining vehicle control under adverse braking conditions by controlling hydraulic brake pressure. This prevents wheel lock-up to help avoid skidding on slippery surfaces during braking.
332 STARTING AND OPERATING situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes. This system monitors the amount of wheel spin of each This can help reduce braking distances. driven wheel. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is Applying the brakes very quickly results in the best BAS reduced to provide enhanced acceleration and stability. assistance.
STARTING AND OPERATING 333 WARNING! (Continued) very slippery surfaces, or hydroplaning. The capabilities of a BAS-equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user’s safety or the safety of others. Hill Start Assist (HSA) The HSA system is designed to assist the driver when starting a vehicle from a stop on a hill.
334 STARTING AND OPERATING Disabling/Enabling HSA 5. Release the clutch pedal (if equipped). If you wish to turn on or off the HSA system, it can be 6. Rotate the steering wheel one-half turn to the left. done using the Customer Programmable Features in the Electronic Vehicle Information Center (EVIC). Refer to 7. Press the “ESC Off” switch (located in the lower switch bank below the climate controls) four times “Electronic Vehicle Information Center (EVIC)” in “Unwithin 20 seconds.
STARTING AND OPERATING 335 Electronic Stability Control (ESC) This system enhances directional control and stability of the vehicle under various driving conditions. The ESC corrects for oversteering and understeering the vehicle by applying the brake of the appropriate wheel. Engine power may also be reduced to assist in counteracting the condition of oversteer or understeer and help the vehicle maintain the desired path.
336 STARTING AND OPERATING The “ESC Off” switch is located in the switch bank near the bottom center of the instrument panel. To enter the The ESC system has three available operating modes: “Partial Off” mode, momentarily press the “ESC Off” ESC On switch and the “ESC Activation/Malfunction Indicator This is the normal operating mode for the ESC. When- Light” will illuminate.
STARTING AND OPERATING 337 WARNING! • When in “Partial Off” mode, the TCS functionality of ESC, (except for the limited slip feature described in the TCS section), has been disabled and the “ESC Off Indicator Light” will be illuminated. When in “Partial Off” mode, the engine power reduction feature of TCS is disabled, and the enhanced vehicle stability offered by the ESC system is reduced.
338 STARTING AND OPERATING WARNING! In the ESC “Full Off” mode, the engine torque reduction and stability features are disabled. Therefore, the enhanced vehicle stability offered by ESC is unavailable. In an emergency evasive maneuver, the ESC system will not engage to assist in maintaining stability. ⴖESC Offⴖ mode is intended for off-highway or off-road use only. NOTE: When the ESC is switched OFF, a feature of the system remains active.
STARTING AND OPERATING 339 when ESC becomes inactive following the maneuver The “ESC Activation/Malfunction Indicator Light” (located in the instrument cluster) starts to flash as soon as that caused the ESC activation. the tires lose traction and the ESC system becomes active. The “ESC Activation/Malfunction Indicator Light” also The “ESC OFF Indicator Light” indicates the flashes when TCS is active.
340 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
STARTING AND OPERATING 341 • Temporary spare tires are designed for temporary • High flotation tire sizing is based on U.S. design emergency use only. Temporary high pressure comstandards and it begins with the tire diameter molded pact spare tires have the letter “T” or “S” molded into into the sidewall. Example: 31x10.5 R15 LT. the sidewall preceding the size designation. Example: T145/80D18 103M. Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ...
342 STARTING AND OPERATING EXAMPLE: R = Construction code — ⬙R⬙ means radial construction — ⬙D⬙ means diagonal or bias construction 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved und
STARTING AND OPERATING 343 EXAMPLE: Load Identification: ⴖ....blank....
344 STARTING AND OPERATING EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation — This symbol certifies that the tire is in compliance with the U.S.
STARTING AND OPERATING 345 Tire Terminology And Definitions Term B-Pillar Cold Tire Inflation Pressure Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
346 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
STARTING AND OPERATING 347 Tire And Loading Information Placard 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
348 STARTING AND OPERATING To determine the maximum loading conditions of your 4. The resulting figure equals the available amount of vehicle, locate the statement “The combined weight of cargo and luggage load capacity. For example, if occupants and cargo should never exceed XXX lbs or “XXX” amount equals 1,400 lbs (635 kg) and there will XXX kg” on the Tire and Loading Information placard.
STARTING AND OPERATING 349 • For the following example, the combined weight of occupants and cargo should never exceed 865 lbs • If your vehicle will be towing a trailer, load from your (392 kg). trailer will be transferred to your vehicle. The following table shows examples on how to calculate total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and number and size of occupants.
350 STARTING AND OPERATING
STARTING AND OPERATING 351 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
352 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Tire Inflation Pressures The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or rear edge of the driver’s side door. At least once a month: • Check and adjust tire pressure with a good quality pocket-type pressure gauge.
STARTING AND OPERATING 353 Inflation pressures specified on the placard are always “cold tire inflation pressure”. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three hour period. The cold tire inflation pressure must not exceed the maximum inflation pressure molded into the tire sidewall.
354 STARTING AND OPERATING WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious collision. Do not drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Radial Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause a collision.
STARTING AND OPERATING 355 All Season Tires — If Equipped All Season tires provide traction for all seasons (spring, summer, fall and winter). Traction levels may vary between different all season tires. All season tires can be identified by the M+S, M&S, M/S or MS designation on the tire sidewall. Use all season tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle.
356 STARTING AND OPERATING While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states prohibit studded tires; therefore, local laws should be checked before using these tire types. Tire Spinning WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone.
STARTING AND OPERATING 357 tread wear indicators, the tire should be replaced. Refer to “Replacement Tires” in this section for further information. Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • Tire pressure • Distance driven • Performance tires, tires with a speed rating of V or higher, and summer tires typically have a reduced tread life. Rotation of these tires per the vehicle maintenance schedule is highly recommended.
358 STARTING AND OPERATING WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Information placard or the Vehicle Certification Label for the size designation of your tire. The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.
STARTING AND OPERATING 359 WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have a collision resulting in serious injury or death.
360 STARTING AND OPERATING • Install on Rear Tires Only. • Due to limited clearance, the Security Chain Company (SCC) Super Z6 low profile traction device or equivalent is recommended on P215/65R17, P225/60R18 or P235/55R18 tires.. • For an All Wheel Drive vehicle, P235/55R19 tire with the use of a traction device that meets the SAE type “Class S” specification is recommended. WARNING! Using tires of different size and type (M+S, Snow) between front and rear axles can cause unpredictable handling.
STARTING AND OPERATING 361 CAUTION! (Continued) • Observe the traction device manufacturer’s instructions on the method of installation, operating speed, and conditions for use. Always use the suggested operating speed of the device manufacturer’s if it is less than 30 mph (48 km/h). • Do not use traction devices on a compact spare tire. These effects can be reduced by timely rotation of tires.
362 STARTING AND OPERATING Tire Rotation — Same tire size on front and rear axle Tire Rotation — Different tire size on front and rear axle The suggested rotation method for vehicles equipped The suggested rotation method is the “side-to-side” as with all season tires is the “forward-cross” as shown in shown in the following diagram. This method is required due to different size tires on the front and rear of the vehicle. the following diagram.
STARTING AND OPERATING 363 also increase as the vehicle is driven - this is normal and there should be no adjustment for this increased presThe Tire Pressure Monitor System (TPMS) will warn the sure. driver of a low tire pressure based on the vehicle recommended cold placard pressure.
364 STARTING AND OPERATING The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information. For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 30 psi (207 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 27 psi (186 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressure to approximately 23 psi (158 kPa).
STARTING AND OPERATING 365 • Seasonal temperature changes will affect tire pressure, and the TPMS will monitor the actual tire pressure in • The TPMS is not intended to replace normal tire care the tire. and maintenance or to provide warning of a tire failure Premium System or condition. NOTE: • The TPMS should not be used as a tire pressure gauge The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to while adjusting your tire pressure.
366 STARTING AND OPERATING • Various TPMS messages, which display in the Electronic Vehicle Information Center (EVIC), and • TPM Telltale Light Tire Pressure Monitoring Low Pressure Warnings The “TPM Telltale Light” will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. In addition, the EVIC will display a “LOW TIRE” message and a graphic showing the pressure values of each tire with the low tire pressure values flashing.
STARTING AND OPERATING 367 will automatically update, the graphic display in the EVIC will stop flashing, and the “TPM Telltale Light” will turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information. Service TPMS Warning If a system fault is detected, the “TPM Telltale Light” will flash on and off for 75 seconds and then remain on solid. The system fault will also sound a chime.
368 STARTING AND OPERATING longer display, and a pressure value will display in place message is then followed with a graphic display with of the dashes. A system fault can occur due to any of the pressure values still shown. This indicates that the pressure values are still being received from the TPM sensors following: but they may not be located in the correct vehicle 1. Signal interference due to electronic devices or driving position.
STARTING AND OPERATING 369 low-pressure warning limit in any of the four active 3. After driving the vehicle for up to 20 minutes above road tires. The vehicle may need to be driven for up to 15 mph (24 km/h), the “TPM Telltale Light” will flash 20 minutes above 15 mph (24 km/h) in order for the on and off for 75 seconds and then remain on solid. In TPMS to receive this information.
370 STARTING AND OPERATING Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the World6.4L Engine wide Fuel Charter, WWFC) which define fuel properties necessary to deliver enhanced emissions, performance, The 6.4L engine is designed to meet all and durability for your vehicle.
STARTING AND OPERATING 371 Gasoline/Oxygenate Blends E-85 Usage In Non-Flex Fuel Vehicles Some fuel suppliers blend unleaded gasoline with oxy- Non-Flex Fuel Vehicles (FFV) are compatible with gasogenates such as Ethanol. Fuels blended with oxygenates line containing 10% ethanol (E10). Gasoline with higher may be used in your vehicle. ethanol content may void the New Vehicle Limited Warranty. CAUTION! DO NOT use gasoline containing Methanol or gasoline containing more than 10% Ethanol.
372 STARTING AND OPERATING To fix a Non-FFV vehicle inadvertently fueled once with without MMT be used in your vehicle. The MMT content of gasoline may not be indicated on the gasoline pump, E-85 perform the following: therefore, you should ask your gasoline retailer whether • Drain the fuel tank (see your authorized dealer). the gasoline contains MMT. MMT is prohibited in Federal and California reformulated gasoline. • Change the engine oil and oil filter.
STARTING AND OPERATING 373 Fuel System Cautions CAUTION! (Continued) CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance and damage the emissions control system. • An out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat.
374 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! (Continued) WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
STARTING AND OPERATING 375 CAUTION! Fuel Fill Cap NOTE: When removing the fuel filler cap, lay the cap tether in the hook, located on the fuel filler door. • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap could let impurities into the fuel system. • A poorly fitting gas cap may cause the “Malfunction Indicator Light (MIL)” to turn on.
376 STARTING AND OPERATING WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • Never add fuel to the vehicle when the engine is running. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. NOTE: • When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
STARTING AND OPERATING 377 VEHICLE LOADING • Gross Vehicle Weight Rating (GVWR) The load carrying capacity of your vehicle is shown on the • Gross Axle Weight Rating (GAWR) front “Vehicle Certification Label”. This information should be • Gross Axle Weight Rating (GAWR) rear used for passenger and luggage loading as indicated. • Vehicle Identification Number (VIN) Do not exceed the specified Gross Vehicle Weight Rating • Type of Vehicle (GVWR) or the Gross Axle Weight Rating (GAWR).
378 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) Overloading The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR. The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and the front and rear GAWR.
STARTING AND OPERATING 379 NOTE: Refer to the “Vehicle Certification Label” affixed to the rear of the driver’s door for your vehicle’s GVWR To load your vehicle properly, first figure out its empty weight, axle-by-axle and side-by-side. Store heavier items and GAWRs. down low and be sure you distribute their weight as TRAILER TOWING evenly as possible. Stow all loose items securely before driving. If weighing the loaded vehicle shows that you Trailer towing with this vehicle is not recommended.
380 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
STARTING AND OPERATING 381 Automatic Transmission — If Equipped Recreational towing (with rear wheels on the ground) is NOT ALLOWED. The only acceptable method for towing this vehicle (behind another vehicle) is on a vehicle trailer with all four wheels OFF the ground. Use of a towing dolly (with rear wheels on the ground) is NOT ALLOWED, as severe transmission damage will occur. Use of a towing dolly (with front wheels on the ground) is not recommended, as vehicle damage may occur.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 HAZARD WARNING FLASHERS . . . . . . . . . . .384 䡵 JUMP-STARTING PROCEDURES . . . . . . . . . . .397 䡵 IF YOUR ENGINE OVERHEATS . . . . . . . . . . . .384 ▫ Preparations For Jump-Start . . . . . . . . . . . . . .398 䡵 WHEEL AND TIRE TORQUE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . .385 ▫ Jump-Starting Procedure . . . . . . . . . . . . . . . .399 ▫ Torque Specifications . . . . . . . . . . . . . . . . . . .386 䡵 TIREFIT KIT — IF EQUIPPED . . . . . . . .
384 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS NOTE: With extended use the Hazard Warning flashers may wear down your battery. The Hazard Warning flasher switch is located in the switch bank near the bottom center of the instrument IF YOUR ENGINE OVERHEATS panel. In any of the following situations, you can reduce the Press the switch to turn on the Hazard Warning potential for overheating by taking the appropriate acflasher. When the switch is activated, all direc- tion.
WHAT TO DO IN EMERGENCIES 385 • You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads 240°F (116°C) or greater pull over and stop the vehicle.
386 WHAT TO DO IN EMERGENCIES Torque Specifications Lug Nut/Bolt Torque **Lug Nut/ Bolt Size 130 Ft-Lbs (176 N·m) M14 x 1.50 Lug Nut/ Bolt Socket Size 22 mm **Use only Chrysler recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Wheel Mounting Surface Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.
WHAT TO DO IN EMERGENCIES 387 After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. TIREFIT KIT — IF EQUIPPED Small punctures up to ¼” (6 mm) in the tire tread can be sealed with TIREFIT. Foreign objects (e.g.
388 WHAT TO DO IN EMERGENCIES TIREFIT Storage TIREFIT Kit Components And Operation The TIREFIT kit is located in the trunk.
WHAT TO DO IN EMERGENCIES 389 Using The Mode Select Knob And Hoses Your TIREFIT kit is equipped with the following symbols to indicate the air or sealant mode. Selecting Air Mode Using The Power Button Push and release the Power Button (4) once to turn On the TIREFIT kit. Push and release the Power Button (4) again to turn Off the TIREFIT kit. Push in the Mode Select Knob (5) and turn to this position for air pump operation only.
390 WHAT TO DO IN EMERGENCIES the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • For optimum performance, make sure the valve stem on the wheel is free of debris before connecting the TIREFIT kit. • You can use the TIREFIT air pump to inflate bicycle tires. The kit also comes with two needles, located in the Accessory Storage Compartment (on the bottom of the air pump) for inflating sport balls, rafts, or similar inflatable items.
WHAT TO DO IN EMERGENCIES 391 WARNING! WARNING! (Continued) • Do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the TIREFIT kit. • Do not use TIREFIT or drive the vehicle under the following circumstances: – If the puncture in the tire tread is approximately 1/4” (6 mm) or larger. – If the tire has any sidewall damage. – If the tire has any damage from driving with extremely low tire pressure.
392 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • TIREFIT Sealant solution contains latex. In case of an allergic reaction or rash, consult a physician immediately. Keep TIREFIT out of reach of children. If swallowed, rinse mouth immediately with plenty of water and drink plenty of water. Do not induce vomiting! Consult a physician immediately. Sealing A Tire With TIREFIT (A) Whenever You Stop To Use TIREFIT: the sealant into the deflated tire and running the air pump.
WHAT TO DO IN EMERGENCIES 393 5. Uncoil the Power Plug (8) and insert the plug into the If the sealant (white fluid) does not flow within 0 – 10 vehicle’s 12 Volt power outlet. seconds through the Sealant Hose (6): NOTE: Do not remove foreign objects (e.g., screws or 1. Press the Power Button (4) to turn Off the TIREFIT kit. nails) from the tire. Disconnect the Sealant Hose (6) from the valve stem. Make sure the valve stem is free of debris.
394 WHAT TO DO IN EMERGENCIES NOTE: If the Mode Select Knob (5) is on Air Mode and If the tire does not inflate to at least 26 psi (1.8 Bar) the pump is operating, air will dispense from the Air pressure within 15 minutes: Pump Hose (7) only, not the Sealant Hose (6). • The tire is too badly damaged. Do not attempt to drive the vehicle further. Call for assistance. If the sealant (white fluid) does flow through the Sealant Hose (6): NOTE: If the tire becomes over-inflated, press the Defla1.
WHAT TO DO IN EMERGENCIES 395 the hose, and place the TIREFIT kit in the vehicle storage location. Quickly proceed to (D) “Drive Vehicle.” CAUTION! • The metal end fitting from Power Plug (8) may get hot after use, so it should be handled carefully. • Failure to reinstall the cap on the fitting at the end of the Sealant Hose (6) can result in sealant contacting your skin, clothing, and the vehicle’s interior.
396 WHAT TO DO IN EMERGENCIES 3. Uncoil the Air Pump Hose (7) (black in color) and 2. Disconnect the TIREFIT kit from the valve stem, screw the fitting at the end of hose (7) onto the valve reinstall the cap on the valve stem and unplug from 12 Volt outlet. stem. 4. Check the pressure in the tire by reading the Pressure 3. Place the TIREFIT kit in its proper storage area in the Gauge (3). vehicle. 4.
WHAT TO DO IN EMERGENCIES 397 (F) Sealant Bottle And Hose Replacement: 1. Uncoil the Sealant Hose (6) (clear in color). 6. Verify that the cap is installed on the fitting at the end of the Sealant Hose (6) and return the hose to its storage area (located on the bottom of the air pump). 2. Locate the round Sealant Bottle release button in the 7. Return the TIREFIT kit to its storage location in the recessed area under the sealant bottle. vehicle. 3. Press the Sealant Bottle release button.
398 WHAT TO DO IN EMERGENCIES CAUTION! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur. WARNING! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. Preparations For Jump-Start Remote Battery Posts Locations The battery is stored under an access cover in the trunk.
WHAT TO DO IN EMERGENCIES 399 WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
400 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Do not connect the jumper cable to the negative (-) post of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. Only use the specific ground point, do not use any other exposed metal parts. Connecting The Jumper Cables 1.
WHAT TO DO IN EMERGENCIES 401 Disconnecting The Jumper Cables 1. Disconnect the negative (-) jumper cable from the remote negative (-) post of the vehicle with the discharged battery. 2. Disconnect the negative end (-) of the jumper cable from the negative (-) post of the booster battery. 3. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery.
402 WHAT TO DO IN EMERGENCIES CAUTION! CAUTION! Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the engine to idle with the transmission in NEUTRAL for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.
WHAT TO DO IN EMERGENCIES 403 WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck and do not let anyone near a spinning wheel, no matter what the speed.
404 WHAT TO DO IN EMERGENCIES 4. Press and maintain firm pressure on the brake pedal. 6. Move the shift lever to the NEUTRAL position. 5. Insert the screwdriver or similar tool into the access hole, 7. The vehicle may then be started in NEUTRAL. and push and hold the override release lever down. 8. Reinstall the shift lever override access cover.
WHAT TO DO IN EMERGENCIES 405 TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial wrecker service.
406 WHAT TO DO IN EMERGENCIES Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equipment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members of the vehicle, not to bumpers or associated brackets. State and local laws regarding vehicles under tow must be observed. If you must use the accessories (wipers, defrosters, etc.
WHAT TO DO IN EMERGENCIES 407 Automatic Transmission The manufacturer recommends towing your vehicle with all four wheels OFF the ground using a flatbed. CAUTION! Towing this vehicle in violation of the above requirements can cause severe transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty.
408 WHAT TO DO IN EMERGENCIES Manual Transmission The manufacturer recommends towing your vehicle with all four wheels OFF the ground using a flatbed. If flatbed equipment is not available, and the transmission is operable, the vehicle may be flat towed (with all four wheels on the ground) under the following conditions: • The transmission must be in NEUTRAL. • The towing speed must not exceed 65 mph (105 km/h). • There is no limitation on towing distance.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMPARTMENT — 6.4L (392 HEMI) . . .411 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . .418 䡵 ONBOARD DIAGNOSTIC SYSTEM — OBD II . .412 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . .419 ▫ Loose Fuel Filler Cap . . . . . . . . . . . . . . . . . .412 ▫ Air Conditioner Maintenance . . . . . . . . . . . . .420 䡵 EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . .413 ▫ Body Lubrication . . . . . .
410 MAINTAINING YOUR VEHICLE ▫ Clutch Hydraulic System (Manual Transmission) — If Equipped . . . . . . . . . . . . . . . . . . . . . . .437 ▫ Manual Transmission — If Equipped . . . . . . .437 ▫ Automatic Transmission — If Equipped . . . . .438 ▫ Rear Axle . . . . . . . . . . . . . . . . . . . . . . . . . . .440 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .440 䡵 FUSES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 411 ENGINE COMPARTMENT — 6.
412 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 413 Trip Odometer button to turn off the message. If the Normally, the OBD II system will be ready. The OBD II problem continues, the message will appear the next time system may not be ready if your vehicle was recently serviced, recently had a dead battery or a battery replacethe vehicle is started. ment. If the OBD II system should be determined not A loose, improperly installed, or damaged fuel filler cap ready for the I/M test, your vehicle may fail the test.
414 MAINTAINING YOUR VEHICLE 3. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced • The MIL will flash for about 10 seconds and then before going to the I/M station. The I/M station can fail return to being fully illuminated until you turn OFF your vehicle because the MIL is on with the engine the ignition or start the engine.
MAINTAINING YOUR VEHICLE 415 available which include detailed service information for MAINTENANCE PROCEDURES your vehicle. Refer to these Service Manuals before The pages that follow contain the required maintenance attempting any procedure yourself. services determined by the engineers who designed your NOTE: Intentional tampering with emissions control vehicle.
416 MAINTAINING YOUR VEHICLE CAUTION! (Continued) • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or air conditioning. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE 417 NOTE: Under no circumstances should oil change in- Engine Oil Viscosity tervals exceed 6,000 miles (10 000 km) or six months, Use Pennzoil Ultra™ 0W-40 engine or equivalent whichever occurs first. MOPAR® oil meeting the Chrysler Material Standard MS-12633 for use in all operating temperatures.
418 MAINTAINING YOUR VEHICLE the engine oil. Engine oil is an engineered product and its of replacement filters varies considerably. Only high performance may be impaired by supplemental addi- quality filters should be used to assure most efficient service. MOPAR® engine oil filters are a high quality oil tives. filter and are recommended. Disposing Of Used Engine Oil And Oil Filters Care should be taken in disposing of used engine oil and Engine Air Cleaner Filter oil filters from your vehicle.
MAINTAINING YOUR VEHICLE 419 Engine Air Cleaner Filter Selection The quality of replacement engine air cleaner filters varies considerably. Only high quality filters should be used to assure most efficient service. MOPAR® engine air cleaner filters are a high quality filter and are recommended. Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic maintenance required.
420 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
MAINTAINING YOUR VEHICLE 421 of the condenser fins and a performance test. Drive belt tension should also be checked at this time. WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs.
422 MAINTAINING YOUR VEHICLE Refrigerant Recovery And Recycling HFO 1234yf — If Equipped 1. Remove the access door in the cowl screen by pressing the retaining clips. HFO 1234yf Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product with a low GWP (Global Warming Potential).
MAINTAINING YOUR VEHICLE 423 2. Unsnap both ends and lift the filter access cover. A/C Air Filter Filter Access Cover 3. Remove the used filter. 5. Close the filter access cover. Refer to the “Maintenance Schedule” for the proper 4. Install the new filter with arrows pointing in the maintenance intervals. direction of airflow, which is toward the rear of the vehicle (text and arrows on the filter will indicate this).
424 MAINTAINING YOUR VEHICLE Body Lubrication Windshield Wiper Blades Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, sliding doors and hood hinges, should be lubricated periodically with a lithium based grease, such as MOPAR® Spray White Lube to assure quiet, easy operation and to protect against rust and wear.
MAINTAINING YOUR VEHICLE 425 The fluid reservoir will hold nearly 1 gal (4 l) of washer fluid when the message “Low Washer Fluid” appears in The windshield washer fluid reservoir is located in the the Electronic Vehicle Information Center (EVIC). front of the engine compartment. Be sure to check the fluid level in the reservoir at regular intervals.
426 MAINTAINING YOUR VEHICLE have an authorized technician inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, have the exhaust system inspected each time the vehicle is raised for lubrication or oil change. Replace as required. WARNING! (Continued) • A hot exhaust system can start a fire if you park over materials that can burn.
MAINTAINING YOUR VEHICLE 427 CAUTION! (Continued) • Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and vehicle.
428 MAINTAINING YOUR VEHICLE • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idle or malfunctioning operating conditions. Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the LOCK position (OFF position for Keyless Enter-N-Go™).
MAINTAINING YOUR VEHICLE 429 Check the coolant recovery bottle tubing for brittle rub- Refer to the “Maintenance Schedule” for the proper ber, cracking, tears, cuts, and tightness of the connection maintenance intervals. at the bottle and radiator. Inspect the entire system for NOTE: Some vehicles require special tools to add coolant leaks. properly. Failure to fill these systems properly could lead With the engine at normal operating temperature (but to severe internal engine damage.
430 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! (Continued) • Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any “globally compatible” coolant (antifreeze).
MAINTAINING YOUR VEHICLE 431 you use the same engine coolant (OAT coolant conforming to MS-12106) throughout the life of your vehicle. (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system.
432 MAINTAINING YOUR VEHICLE Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery tank. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution.
MAINTAINING YOUR VEHICLE 433 service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only Used ethylene glycol-based engine coolant (antifreeze) is be checked once a month. a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal When additional coolant is needed to maintain the rules for your community. To prevent ingestion by ani- proper level, it should be added to the coolant bottle.
434 MAINTAINING YOUR VEHICLE • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the • Check the coolant freeze point in the radiator and in condenser clean. the coolant expansion bottle. If engine coolant (antifreeze) needs to be added, the contents of the coolant • Do not change the thermostat for Summer or Winter operation.
MAINTAINING YOUR VEHICLE 435 WARNING! Overfilling of fluid is not recommended because it may cause leaking in the system. Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency.
436 MAINTAINING YOUR VEHICLE WARNING! WARNING! (Continued) • Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid for your vehicle is also identified on the original factory installed hydraulic master cylinder reservoir.
MAINTAINING YOUR VEHICLE 437 WARNING! (Continued) • Do not allow petroleum based fluid to contaminate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in a collision. Manual Transmission — If Equipped Fluid Level Check Check the fluid level by removing the fill plug on the left side of the transmission. The fluid level should be 1/4 inch (6.4mm) below the bottom of the fill hole. Add fluid, if necessary, to maintain the proper level.
438 MAINTAINING YOUR VEHICLE Automatic Transmission — If Equipped Selection Of Lubricant It is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s specified transmission fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for fluid specifications. It is important to maintain the transmission fluid at the correct level using the recommended fluid.
MAINTAINING YOUR VEHICLE 439 CAUTION! CAUTION! Do not use chemical flushes in your transmission as the chemicals can damage your transmission components. Such damage is not covered by the New Vehicle Limited Warranty. If a transmission fluid leak occurs, visit your authorized dealer immediately. Severe transmission damage may occur. Your authorized dealer has the proper tools to adjust the fluid level accurately.
440 MAINTAINING YOUR VEHICLE Rear Axle Appearance Care And Protection From Corrosion Fluid Level Check Protection Of Body And Paint From Corrosion Checking the fluid level while the vehicle is on level Vehicle body care requirements vary according to geoground will improve the accuracy of the fluid level graphic locations and usage. Chemicals that make roads reading.
MAINTAINING YOUR VEHICLE 441 • If insects, tar, or other similar deposits have accumulated on your vehicle, use MOPAR® Super Kleen Bug Corrosion is the result of deterioration or removal of and Tar Remover to remove. paint and protective coatings from your vehicle. • Use a high quality cleaner wax, such as MOPAR® The most common causes are: Cleaner Wax to remove road film, stains and to protect • Road salt, dirt and moisture accumulation. your paint finish. Take care never to scratch the paint.
442 MAINTAINING YOUR VEHICLE • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well • If you drive on salted or dusty roads or if you drive packaged and sealed. near the ocean, hose off the undercarriage at least once a month. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.
MAINTAINING YOUR VEHICLE 443 NOTE: If your vehicle is equipped with Dark Vapor Chrome wheels DO NOT USE wheel cleaners, abrasives or polishing compounds. They will permanently damage this finish and such damage is not covered by the New Vehicle Limited Warranty. USE ONLY MILD SOAP AND WATER WITH A SOFT CLOTH. Used on a regular basis this is all that is required to maintain this finish. CAUTION! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner.
444 MAINTAINING YOUR VEHICLE liquid. Please do not use polishes, oils, cleaning fluids, solvents, detergents, or ammonia-based cleaners to clean Use MOPAR® Fabric Cleaner or equivalent to clean your leather upholstery. Application of a leather condifabric upholstery and MOPAR® Carpet Cleaner or tioner is not required to maintain the original condition. equivalent for carpeting. Interior Care Interior Trim should be cleaned starting with a damp cloth, or MOPAR® Satin Select or equivalent.
MAINTAINING YOUR VEHICLE 445 To minimize the possibility of scratching the lenses and When cleaning the rear view mirror, spray cleaner on the reducing light output, avoid wiping with a dry cloth. To towel or rag that you are using. Do not spray cleaner remove road dirt, wash with a mild soap solution fol- directly on the mirror. lowed by rinsing.
446 MAINTAINING YOUR VEHICLE If the belts need cleaning, use MOPAR® Total Clean, a FUSES mild soap solution, or lukewarm water. Do not remove the belts from the vehicle to wash them. Dry with a soft WARNING! cloth. • When replacing a blown fuse, always use an approReplace the belts if they appear frayed or worn or if the priate replacement fuse with the same amp rating as buckles do not work properly. the original fuse. Never replace a fuse with another fuse of higher amp rating.
MAINTAINING YOUR VEHICLE 447 WARNING! (Continued) • If a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer. Integrated Power Module The Integrated Power Module is located in the engine compartment. This module contains fuses and relays.
448 MAINTAINING YOUR VEHICLE CAUTION! • When installing the integrated power module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the integrated power module and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
MAINTAINING YOUR VEHICLE 449 Cavity 7 Cartridge Fuse — 8 — 9 10 11 12 — 30 Amp Pink 30 Amp Pink 40 Amp Green MiniFuse Description Cavity 25 Amp Natural 30 Amp Green — — Headlamp Washer Relay – If Equipped Starter 13 — Anti-Lock Brake System (ABS) Valves Radiator Fan Lo/ High — — Windshield Wiper 14 15 16 17 18 19 20 21 22 Cartridge Fuse 50 Amp Red MiniFuse Description — — 50 Amp Red — — — — — — — — — Anti-Lock Brake System (ABS) Pump Motor — Radiator Fan — — — — — — — — — — — — —
450 MAINTAINING YOUR VEHICLE Rear Power Distribution Center There is also a power distribution center located in the trunk under the spare tire access panel. This center contains fuses and relays. Rear Power Distribution Center CAUTION! • When installing the power distribution center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure.
MAINTAINING YOUR VEHICLE 451 Cavity 1 2 3 Cartridge Fuse 60 Amp Yellow 40 Amp Green — MiniFuse Description Cavity — Ignition Off Draw (IOD) Cavity 1 of the Rear Power Distribution Center contains a black IOD fuse needed for vehicle processing during assembly. The service replacement part is a 60 Amp yellow cartridge fuse.
452 MAINTAINING YOUR VEHICLE Cavity 9 Cartridge Fuse — 10 — 11 * 12 * 13 * 14 — — — — 15 — MiniFuse Description Cavity 20 Amp Yellow 25 Amp Natural — — — 10 Amp Red Power Outlet 16 Cartridge Fuse — Vacuum Pump – If Equipped — — — AC Heater Control/ Cluster/Security Module – If Equipped Active Damper – If Equipped 17 — 18 — 19 — 20 21 22 23 24 25 — — — — — — 20 Amp Yellow MiniFuse Description 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 10 Amp Red — — — — — — Heated Seat Module – I
MAINTAINING YOUR VEHICLE 453 Cavity 26 27 Cartridge Fuse — — 28 — 29 — MiniFuse Description Cavity — 10 Amp Red 15 Amp Blue — Occupant Restraint Controller (ORC) Ignition Run, AC Heater Control/ Occupant Restraint Controller (ORC) Cluster/Electronic Stability Control (ESC)/Powertrain Control Module (PCM)/STOP LIGHT Switch 30 Cartridge Fuse — 31 32 33 34 35 — — — — — — — — — 5 Amp Orange 36 — 25 Amp Natural 5 Amp Orange MiniFuse Description 10 Amp Red Door Modules/ Power Mirrors/ Ste
454 MAINTAINING YOUR VEHICLE Cavity 37 Cartridge Fuse — 38 — 39 — 40 — 41 42 — 30 Amp Pink MiniFuse Description Cavity 15 Amp Blue 10 Amp Red Transmission 43 Cargo Light/Vehicle Information Module – If Equipped Heated Mirrors – If Equipped Auto Inside Rearview Mirror/Heated Seats – If Equipped/ Switch Bank — Front Blower Motor 44 10 Amp Red 5 Amp Orange — — Cartridge Fuse 30 Amp Pink 20 Amp Blue MiniFuse Description — Rear Window Defroster Amplifier/Sunroof – If Equipped — *Cavit
MAINTAINING YOUR VEHICLE 455 VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery. • Disconnect the negative cable from the battery. • Anytime you store your vehicle, or keep it out of service (e.g., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.
456 MAINTAINING YOUR VEHICLE Exterior Bulbs Headlamp – High Intensity Discharge (HID) Halogen Headlamp Front Park/Turn Lamp Front Fog Lamp Front Side Marker Tail Lamp Tail/Stop/Turn Lamp Rear Side Marker Backup Lamp Center High-Mount Stop Lamp (CHMSL) License BULB REPLACEMENT Bulb Number D1S (Serviced at Authorized Dealer) H13 3157A PSX24W (Serviced at Authorized Dealer) 168 3057K 3057K 168 921 LED (Serviced at Authorized Dealer) 168 NOTE: Lens fogging can occur under certain atmospheric conditions.
MAINTAINING YOUR VEHICLE 457 HID Headlamps Front/Rear Side Marker Lamp The headlamps are a type of high voltage discharge tube. 1. Remove the front/rear side marker. Use a fiber stick or High voltage can remain in the circuit even with the similar tool to gently pry the lamp on the outboard headlamp switch off and the key removed. Because of side to disengage the clip. this, you should not attempt to service a headlamp bulb NOTE: If a screwdriver is used, make sure a soft material yourself.
458 MAINTAINING YOUR VEHICLE Tail/Turn And Stop Lamp 1. Open the trunk. 3. Remove the fasteners from the back of the tail lamp assembly. 2. Using a screwdriver, remove the tail lamp retainer. Tail Lamp Fasteners 4. Pull back the trunk liner.
MAINTAINING YOUR VEHICLE 459 5. Remove the remaining fasteners from the back of the 7. Push the electrical connector locking tab to the side. tail lamp assembly. 8. Disconnect the electrical connector. 6. Pull the tail lamp assembly clear from the vehicle to 9. Turn the appropriate bulb and socket assembly counaccess the bulbs. terclockwise to remove it from the tail lamp assembly. 10. Disconnect the bulb from the socket assembly and install the replacement bulb. 11.
460 MAINTAINING YOUR VEHICLE 13. Reinstall tail lamp retainer. Center Tail/Backup Lamp See your authorized dealer for bulb replacement. Center High-Mounted Stop Lamp (CHMSL) The CHMSL uses LED lamps that are not serviceable separately. The CHMSL must be replaced as an assembly, see your authorized dealer. License Lamp 1. Remove the screws securing the lamp to the rear fascia. 2. Remove the bulb and socket assembly. Reinstall Tail Lamp Retainer 14. Close the trunk.
MAINTAINING YOUR VEHICLE 461 3. Disconnect the bulb from the socket assembly and 4. Reinstall the bulb and socket assembly. install the replacement bulb. 5. Reattach the lamp to the rear fascia, and then install the screws.
462 MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Fuel (Approximate) 19 Gallons Engine Oil With Filter 6.4 Liter Engine (SAE 0W-40, Synthetic API Certified) 7 Quarts Cooling System * 6.4 Liter Engine (MOPAR Antifreeze/Engine Coolant (OAT coolant 15 Quarts conforming to MS-12106) 10 Year/150,000 Mile Formula or equivalent) * Includes heater and coolant recovery bottle filled to MAX level. Metric 72 Liters 6.6 Liters 14.
MAINTAINING YOUR VEHICLE 463 FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT coolant conforming to MS-12106. For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends full synthetic engine oils.
464 MAINTAINING YOUR VEHICLE Chassis Component Manual Transmission – If Equipped Automatic Transmission – If Equipped Brake Master Cylinder Power Steering Reservoir Rear Axle Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® ATF+4® Automatic Transmission Fluid. Use only ATF+4® Automatic Transmission Fluid. Failure to use ATF+4® fluid may affect the function or performance of your transmission. We recommend MOPAR® ATF+4® fluid. We recommend you use MOPAR® DOT 3, SAE J1703 should be used.
M A I N T E N A ▫ Required Maintenance Intervals . . . . . . . . . . .467 N C E MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULE . . . . . . . . . . . . .
M A I N T E N A N C E 466 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE The Scheduled Maintenance services listed in this manual must be done at the times or mileages specified to protect your vehicle warranty and ensure the best vehicle performance and reliability. More frequent maintenance may be needed for vehicles in severe operating conditions, such as dusty areas and very short trip driving. Inspection and service should also be done anytime a malfunction is S suspected.
MAINTENANCE SCHEDULES 467 M referring to the steps described under “Electronic Vehicle • Check the fluid levels of the coolant reservoir, brake Information Center (EVIC)/Oil Change Required” in master cylinder, and power steering, and add as needed. “Understanding Your Instrument Panel” for further information. • Check all lights and other electrical items for correct operation. At Each Stop For Fuel • Check the engine oil level.
M 468 MAINTENANCE SCHEDULES A I 6,000 Miles (10,000 km) or 6 N T Months Maintenance Service E Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E S C H E D U L E S 8 Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
MAINTENANCE SCHEDULES 469 M 18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Inspect the rear axle fluid. ❏ Inspect the manual transmission fluid (if equipped), add as necessary. Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
M 470 MAINTENANCE SCHEDULES A I 30,000 Miles (50,000 km) or 30 N T Months Maintenance Service E Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C ❏ Replace the engine air cleaner filter. E S C H E D U L E S 8 ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
MAINTENANCE SCHEDULES 471 M 42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
M 472 MAINTENANCE SCHEDULES A I 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule N ❏ Change the engine oil and engine oil filter. T ❏ Rotate tires. E ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. N ❏ Inspect the brake linings, and replace if necessary. A ❏ Inspect the CV joints. N ❏ Inspect the exhaust system.
MAINTENANCE SCHEDULES 473 M 54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Inspect the rear axle fluid. ❏ Inspect the manual transmission fluid (if equipped), add as necessary. Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires.
M 474 MAINTENANCE SCHEDULES A I 66,000 Miles (110,000 km) or N T 66 Months Maintenance SerE vice Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E S C H E D U L E S 8 Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
MAINTENANCE SCHEDULES 475 M 78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary.
M 476 MAINTENANCE SCHEDULES A I 90,000 Miles (150,000 km) or N T 90 Months Maintenance SerE vice Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C ❏ Replace the engine air cleaner filter. E S C H E D U L E S 8 ❏ Inspect and replace the PCV Valve if necessary.* ❏ Inspect the rear axle fluid. ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ Inspect the manual transmission fluid (if equipped), add as necessary.
MAINTENANCE SCHEDULES 477 M 102,000 Miles (170,000 km) or 102 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
M 478 MAINTENANCE SCHEDULES A I 114,000 Miles (190,000 km) or N T 114 Months Maintenance SerE vice Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires.
MAINTENANCE SCHEDULES 479 M 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Flush and replace the engine coolant at 120 months or 150,000 miles (240 000 km) whichever comes first. Inspect the brake linings, and replace if necessary. Adjust parking brake on vehicles equipped with four-wheel disc brakes. Inspect the CV joints. Inspect the exhaust system.
M 480 MAINTENANCE SCHEDULES A I 126,000 Miles (210,000 km) or N T 126 Months Maintenance SerE vice Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C ❏ Inspect the rear axle fluid. E S C H E D U L E S 8 ❏ Inspect the manual transmission fluid (if equipped), add as necessary. Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 132,000 Miles (220,000 km) or 132 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter.
MAINTENANCE SCHEDULES 481 M 138,000 Miles (230,000 km) or 138 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
M 482 MAINTENANCE SCHEDULES A I 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule N ❏ Change the engine oil and engine oil filter. T ❏ Rotate tires. E ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. N ❏ Inspect the brake linings, and replace if necessary. A ❏ Inspect the CV joints. N ❏ Inspect the exhaust system.
MAINTENANCE SCHEDULES 483 M 150,000 Miles (250,000 km) or 150 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Flush and replace the engine coolant at 150,000 miles (240 000 km) or 120 months whichever comes first. ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
M A I N T E N A N C E S C H E D U L E S 8 484 MAINTENANCE SCHEDULES * This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . .487 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY). . . . . . . . . . . . . . . . . . .489 ▫ Prepare For The Appointment. . . . . . . . . . . . .487 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . .489 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . .487 䡵 WARRANTY INFORMATION . . . . . . . . . . . . .
486 IF YOU NEED CONSUMER ASSISTANCE 䡵 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES . . . . . . . . . . . . . . . . .493 ▫ Treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .493 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . .493 ▫ Temperature Grades. . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 487 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment Be Reasonable With Requests If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an appointment.
488 IF YOU NEED CONSUMER ASSISTANCE facilities, factory-trained technicians, special tools, and • Authorized dealer name the latest information to ensure the vehicle is fixed • Vehicle Identification Number (VIN) correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to an authorized dealer service manager first. Most matters can be re- Chrysler Group LLC Customer Center solved with this process. P.O.
IF YOU NEED CONSUMER ASSISTANCE 489 Mexico, D. F. Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered by Bell Canada. For TTY teletypewriter users, dial 711 and for Voice callers, dial 1-800-855-0511 to connect with a Bell Relay Service operator.
490 IF YOU NEED CONSUMER ASSISTANCE The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a service contract that is not a manufacturer’s service contract, and you require service after the manufacturer’s New Vehicle Limited Warranty expires, please refer to the contract documents, and contact the person listed in those documents.
IF YOU NEED CONSUMER ASSISTANCE 491 campaign. However, NHTSA cannot become involved in individual problems between you, your authorized MOPAR® fluids, lubricants, parts, and accessories are dealer, and the manufacturer. available from an authorized dealer. They are recommended for your vehicle in order to help keep the vehicle To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), operating at its best. or go to http://www.safercar.
492 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.
IF YOU NEED CONSUMER ASSISTANCE 493 Call toll free at: Treadwear • 1–800–890–4038 (U.S.) The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
494 IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10
496 INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . . .325 ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . . .328 Adding Engine Coolant (Antifreeze) . . . . . . . . . . . .430 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .374 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . .425 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .372 Airbag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 497 Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . .439 Fluid and Filter Changes . . . . . . . . . . . . . . . . . .439 Fluid Change . . . . . . . . . . . . . . . . . . . . . . . . . .439 Fluid Level Check . . . . . . . . . . . . . . . . . . . . . . .439 Fluid Type . . . . . . . . . . . . . . . . . . . . . . . . . . . .464 Special Additives . . . . . . . . . . . . . . . . . . . . . . .438 Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .311 Auto Unlock, Doors . .
498 INDEX Radiator (Coolant Pressure) . . . . . . . . . . . . . . . .432 Carbon Monoxide Warning . . . . . . . . . . . . . . . . . . .94 Cargo (Vehicle Loading) . . . . . . . . . . . . . . . . . . . .377 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . .441 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . . . .276 Center High Mounted Stop Light . . . . . . . . . . . . . .460 Certification Label. . . . . . . . . . . . . . . . . . . . . . . . .377 Chains, Tire . . . . . . . .
INDEX 499 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . .433 Points to Remember . . . . . . . . . . . . . . . . . . . . .433 Pressure Cap . . . . . . . . . . . . . . . . . . . . . . . . . .432 Radiator Cap . . . . . . . . . . . . . . . . . . . . . . . . . .432 Selection of Coolant (Antifreeze) . . . . . . . . . . . . .429 Corrosion Protection . . . . . . . . . . . . . . . . . . . . . . .440 Cruise Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .208 Cupholders . . . . . . .
500 INDEX Electronic Stability Control (ESC) . . . . . . . . . . . . . .335 Electronic Throttle Control Warning Light . . . . . . . .209 Electronic Vehicle Information Center (EVIC) . . . . . .218 Emergency Deck Lid Release . . . . . . . . . . . . . . . . . .44 Emergency, In Case of Freeing Vehicle When Stuck . . . . . . . . . . . . . . . .401 Hazard Warning Flasher . . . . . . . . . . . . . . . . . .384 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . .397 Overheating . . . . . . . . . . .
INDEX 501 Exhaust Gas Caution. . . . . . . . . . . . . . . . . . . . . . . .94 Exhaust System . . . . . . . . . . . . . . . . . . . . . . . . . . .94 Exterior Folding Mirrors . . . . . . . . . . . . . . . . . . . .105 Exterior Lighting. . . . . . . . . . . . . . . . . . . . . . . . . .157 Exterior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . .97 Filler Location Fuel . . . . . . . . . . . . . . . . . . . . . . . .374 Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .
502 INDEX Methanol . . . . . . . . . . . . . . . . . Octane Rating . . . . . . . . . . . . . . Requirements . . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . Tank Capacity . . . . . . . . . . . . . . Fueling . . . . . . . . . . . . . . . . . . . . Fuel System Caution . . . . . . . . . . . Fuses . . . . . . . . . . . . . . . . . . . . . . Garage Door Opener (HomeLink®) Gas Cap (Fuel Filler Cap) . . . . . . . Gasoline, Clean Air . . . . . . . . . . . . Gasoline (Fuel) . . . . . . . . . .
INDEX 503 Time Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . .158 Washers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .425 Headlight Washers . . . . . . . . . . . . . . . . . . . . . . . .425 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . .152 Head Rests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152 Heated Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . .107 Heated Seats. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
504 INDEX Kicker Sound System. . . . . . . . . . . . . . . . . . . . . . .272 Knee Bolster. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 Lane Change and Turn Signals . . . . . . . . . . . . . . . .161 Lane Change Assist . . . . . . . . . . . . . . . . . . . . . . . .162 Lap/Shoulder Belts. . . . . . . . . . . . . . . . . . . . . . . . .48 Latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97 Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 505 High Beam Indicator . . . . . . . . . . . . . . . . . . . . .212 High Beam/Low Beam Select . . . . . . . . . . . . . . .162 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . .22 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . .157 Intensity Control . . . . . . . . . . . . . . . . . . . . . . . .163 Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163 License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .460 Lights On Reminder . . . . . .
506 INDEX Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . .466 Malfunction Indicator Light (Check Engine). . . . . . .217 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . .492 Manual Transmission . . . . . . . . . . . . . . . . . . . . . .298 Fluid Level Check . . . . . . . . . . . . . . . . . . . . . . .437 Shift Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . .300 Map/Reading Lights . . . . . . . . . . . . . . . . . . . . . . .162 Master Cylinder (Brakes) . . .
INDEX 507 Filter Disposal . . . . . . . . . . . . . . . . . . . . . . . . .418 Materials Added to . . . . . . . . . . . . . . . . . . . . . .417 Recommendation . . . . . . . . . . . . . . . . . . . . . . .417 Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . . .417 Viscosity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .417 Oil Filter, Selection . . . . . . . . . . . . . . . . . . . . . . . .418 Onboard Diagnostic System . . . . . . . . . . . . . . . . . .
508 INDEX Pretensioners Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 Programmable Electronic Features . . . . . . . . . . . . .235 Programming Transmitters (Remote Keyless Entry) . . . .23 Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . . .354 Radiator Cap (Coolant Pressure Cap) . . . . . . . . . . .432 Radio Operation . . . . . . . . . . . . . . . . . . . . . . . . . .276 Radio Remote Controls . . . . . . . . . . . . . . . . . . . . .274 Rear Cupholder . . . .
INDEX 509 Safety Defects, Reporting . . . . . . . . . . . . . . . . . . . .491 Safety, Exhaust Gas. . . . . . . . . . . . . . . . . . . . . . . . .94 Safety Information, Tire . . . . . . . . . . . . . . . . . . . . .340 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94 Satellite Radio Antenna . . . . . . . . . . . . . . . . . . . . .262 Schedule, Maintenance . . . . . . . . . . . . . . . . . . . . .466 Seat Belt Maintenance . . . . . . . . . . . . . . . . . . . . . .
510 INDEX Settings, Personal . . . . . . . . . . . . . . . . . . . . . . . . .235 Setting the Clock. . . . . . . . . . . . . . . . . . . . . . . . . .241 Shift Indicator Light . . . . . . . . . . . . . . . . . . . . . . .300 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .301 Automatic Transmission . . . . . . . . . . . . . . . . . .301 Shift Lever Override . . . . . . . . . . . . . . . . . . . . . . .403 Shift Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 511 Steering Wheel Audio Controls . . . . . . . . . . . . . . .274 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . .340 Steering Wheel Mounted Sound System Controls . . .274 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97 Aging (Life of Tires) . . . . . . . . . . . . . . . . . . . . .357 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .455 Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . .351 Storage, Vehicle. . .
512 INDEX Spinning . . . . . . . . . . . . . Tread Wear Indicators . . . . Tire Safety Information . . . . . To Open Hood . . . . . . . . . . . Towing . . . . . . . . . . . . . . . . 24-Hour Towing Assistance Disabled Vehicle . . . . . . . . Recreational . . . . . . . . . . . Towing Assistance. . . . . . . . . Traction . . . . . . . . . . . . . . . . Traction Control . . . . . . . . . . Trailer Towing . . . . . . . . . . . Transmission . . . . . . . . . . . . Automatic . . . . . . . . . . . . Fluid . . . .
INDEX 513 Uconnect® 130 With Satellite Radio Playing MP3 Files . . . . . . . . . . . . . . . . . . . . . . .257 Uconnect® phone . . . . . . . . . . . . . . . . . . . . . . . . .121 Uniform Tire Quality Grades . . . . . . . . . . . . . . . . .493 Universal Consumer Interface (UCI) Connector . . . .265 Universal Garage Door Opener (HomeLink®) Programming HomeLink® . . . . . . . . . . . . . . . . .182 Unleaded Gasoline . . . . . . . . . . . . . . . . . . . . . . . .370 Untwisting Procedure, Seat Belt . . . .
514 INDEX Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Windshield Wipers . . . . . . . . . . . . . . . . . . . . . . . .164 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Wiper Blade Replacement . . . . . . . . . . . . . . . . . . .424 Windshield Defroster . . . . . . . . . . . . . . . . . . . . . . .95 Wipers, Intermittent . . . . . . . . . . . . . . . . . . . . . . .165 Windshield Washers . . . . . . . . . . . . . . . . . . . . . . .164 Fluid . . . .
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
OWNER’S MANUAL Chrysler Group LLC 14D492-126-AB 14PFD41-126-AA First Edition Second Edition Dar t Printed in U.S.A. 1409672cv1 14PFD41-126-AA Dart Chrysler 1" gutter 09/03/2013 10:49:27 2014 Dar t 2014 OWNER’S MANUAL Chrysler Group LLC 14PFD41-126-AA First Edition Printed in U.S.A.
