2015 OWNER’S MANUAL Challenger
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated nondrinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS ! INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .4 ! VEHICLE IDENTIFICATION NUMBER . . . . . . . .6 ! HOW TO USE THIS MANUAL . . . . . . . . . . . . . .4 ! VEHICLE MODIFICATIONS/ALTERATIONS . . . .7 ! WARNINGS AND CAUTIONS . . . . . . . . . . . . . .
4 INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained techLLC vehicle. Be assured that it represents precision nicians and genuine parts, and cares about your satisfacworkmanship, distinctive styling, and high quality - all tion. essentials that are traditional to our vehicles.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owners Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is on the left front corner of the instrument panel.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. VIN Location NOTE: It is illegal to remove or alter the VIN.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS ! A WORD ABOUT YOUR KEYS . . . . . . . . . . . . .12 ! VEHICLE SECURITY ALARM . . . . . . . . . . . . . .18 ▫ Keyless Ignition Node (KIN) . . . . . . . . . . . . . .12 ▫ Rearming Of The System . . . . . . . . . . . . . . . . .19 ▫ Key Fob . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . .19 ▫ Ignition Or Accessory On Message . . . . . . . . . .15 ▫ To Disarm The System . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Unlatch The Trunk . . . . . . . . . . . . . . . . . . .24 ! WINDOWS . . . . . . . . . . . . . . . . . . . . . . . . . . .38 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .24 ▫ Power Windows . . . . . . . . . . . . . . . . . . . . . . .38 ▫ Programming Additional Transmitters . . . . . . .25 ▫ AUTO-Down Feature — If Equipped . . . . . . . .39 ▫ Transmitter Battery Replacement . . . . . . . . . . .25 ! TRUNK LOCK AND RELEASE . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ! ENGINE BREAK-IN RECOMMENDATIONS . . . .90 ! SAFETY TIPS . . . . . . . . . . . . . . . . . . . . . . . . . .93 ▫ Transporting Passengers. . . . . . . . . . . . . . . . . .93 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . .94 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 ▫ Periodic Safety Checks You Should Make Outside The Vehicle . . . . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Keyless Ignition Node (KIN System) has four operating positions, three of which are labeled and will Your vehicle uses a keyless ignition system. This system illuminate when in position. The three positions are: OFF, consists of a Key Fob with Remote Keyless Entry (RKE) ACC, and ON/RUN. The fourth position is START. transmitter and a Keyless Ignition Node (KIN). During start, ON/RUN will illuminate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the Key Fob go dead. The emergency key is also for locking/unlocking the glove compartment. You can keep the emergency key with you when valet parking.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To remove the emergency key, slide the mechanical latch on the back of the Key Fob sideways with your thumb and then pull the key out with your other hand. Emergency Key Removal NOTE: You can insert the double-sided emergency key into the lock cylinders with either side up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Ignition Or Accessory On Message Opening the driver’s door when the ignition is in ACC or ON (engine not running), a chime will sound to remind you to cycle the ignition to OFF. In addition to the chime, the ignition or accessory on message will display in the cluster.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. CAUTION! An unlocked car is an invitation to thieves. Always remove the Key Fob from vehicle, place the ignition in the OFF and lock all doors when leaving the vehicle unattended.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer. CAUTION! The Sentry Key® Immobilizer system is not compatible with some aftermarket remote starting systems.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Duplication of Key Fobs may be performed at an autho- • This device must accept any interference that may be received, including interference that may cause underized dealer. This procedure consists of programming a sired operation. blank Key Fob to the vehicle electronics. A blank Key Fob is one that has never been programmed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 Rearming Of The System If something triggers the alarm, and no action is taken to disarm it, the system will turn off the horn after approximately 29 seconds, turn off all of the visual signals after 5 seconds, and then the system will rearm itself up to 8 times. To Arm The System Follow these steps to arm the Vehicle Security Alarm: 1.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Vehicle Security Alarm remains armed during power trunk entry. Pushing the trunk button will not The Vehicle Security Alarm can be disarmed using any of disarm the Vehicle Security Alarm. If someone enters the following methods: the vehicle through the trunk and opens any door, the • Push the UNLOCK button on the Remote Keyless alarm will sound. Entry (RKE) transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 remain armed when the battery is reconnected; the This feature also turns on the approach lighting in the exterior lights will flash, and the horn will sound. If this outside mirrors — if equipped. Refer to “Mirrors” in “Understanding The Features Of Your Vehicle” for furoccurs, disarm the Vehicle Security Alarm. ther information.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY (RKE) The RKE system allows you to lock or unlock the doors, open the trunk, or activate the Panic Alarm from distances up to approximately 66 ft (20 m) using a hand-held Key Fob with RKE transmitter. The RKE transmitter does not need to be pointed at the vehicle to activate the system. NOTE: Driving at speeds 5 mph (8 km/h) and above disables the system from responding to all RKE transmitter buttons for all RKE transmitters.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 If the vehicle is equipped with Passive Entry, refer to Headlight Illumination On Approach “Keyless Enter-N-Go™” under “Things To Know Before This feature activates the headlights for up to 90 seconds Starting Your Vehicle” for further information. when the doors are unlocked with the RKE transmitter. The time for this feature is programmable on vehicles 1st Push Of Key Fob Unlocks equipped through Uconnect®.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE second and release. When the Panic Alarm is activated, the turn signals will flash, the horn will pulse on and off, This feature will cause the horn to chirp when the doors and the interior lights will turn on. are locked with the RKE transmitter. This feature can be turned on or turned off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Programming Additional Transmitters Programming Key Fobs or RKE transmitters may be performed at an authorized dealer. Transmitter Battery Replacement The recommended replacement battery is one CR2032 battery. NOTE: • Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate • Do not touch the battery terminals that are on the back Keyless Ignition Node (KIN) Emergency Key Removal housing or the printed circuit board. 2.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE on the battery to the + sign on the inside of the battery clip, located on the back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 4. To assemble the RKE transmitter case, snap the two halves together, reposition and secure the screw as shown in step #2 for removal.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 NOTE: Changes or modifications not expressly approved REMOTE STARTING SYSTEM — IF EQUIPPED by the party responsible for compliance could void the user’s authority to operate the equipment. This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conveIf your RKE transmitter fails to operate from a normal niently from outside the vehicle while still distance, check for these two conditions: maintaining security.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Use Remote Start All of the following conditions must be met before the engine will remote start: • Shift lever in PARK • Doors closed • Hood closed • Hazard switch off • Brake switch inactive (brake pedal not pushed) • Battery at an acceptable charge level • RKE PANIC button not pushed • System not disabled from previous remote start event • Vehicle security alarm not active • Ignition in Off position (Keyless Enter-N-Go™) WARNING! • Do not start
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 will flash, and horn will chirp twice (if programmed). To Exit Remote Start Mode Without Driving The Then, the engine will start and the vehicle will remain in Vehicle the Remote Start mode for a 15-minute cycle. Push and release the REMOTE START button one time or allow the engine to run for the entire 15-minute cycle.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For vehicles equipped with the Keyless Enter-N- DOOR LOCKS Go™ feature, the message “Push Button/Insert Key” will Manual Door Locks display in the Driver Information Display (DID) until To lock each door, push the door lock knob on each door you push the START button. trim panel downward. To unlock each door, pull the door Cancel Remote Start lock knob on each door trim panel upward.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 If the door lock knob is down when you shut the door, the door will lock. Therefore, make sure the Key Fob is not inside the vehicle before closing the door. WARNING! • For personal security and safety in the event of a collision, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • When leaving the vehicle, remove the Key Fob from the vehicle and lock your vehicle.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks The power door lock switch is located on each door trim panel. Use this switch to lock or unlock the doors. The doors can also be locked and unlocked with the Keyless Enter-N-Go™ (Passive Entry) system. For further information, refer to “Keyless Enter-N-Go™” in “Things To Know Before Starting Your Vehicle.” If you push the power door lock switch while the ignition is on, and either door is open, the power locks will not operate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Automatic Unlock Doors On Exit Automatic Unlock Doors On Exit Programming The doors will unlock automatically if: 1. 2. 3. 4. 5. 6. The Automatic Unlock Doors On Exit feature can be enabled or disabled. Refer to “Uconnect® Settings” in The Automatic Unlock Doors On Exit feature is en“Understanding Your Instrument Panel” for further inabled. formation.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To Unlock From The Driver’s Side: • Passive Entry may be programmed ON/OFF; refer to With a Passive Entry RKE transmitter within 5 ft (1.5 m) “Uconnect® Settings” in “Understanding Your Instru- of the driver door handle, grab the front driver door ment Panel” for further information. handle to unlock the driver’s door automatically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 NOTE: If “Unlock All Doors 1st Press” is programmed all doors will unlock when you grab hold of the front driver’s door handle. To select between “Unlock Driver Door 1st Press” and “Unlock All Doors 1st Press,” refer to “Uconnect® Settings” in “Understanding Your Instrument Panel” for further information. To Unlock From The Passenger Side: With a Passive Entry RKE transmitter within 5 ft (1.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If you inadvertently leave your vehicle’s Passive Entry RKE transmitter in the trunk and try to close the With a Passive Entry RKE transmitter within 5 ft (1.5 m) deck lid, the deck lid will automatically unlatch, unless of the deck lid, push the button located on the center of another one of the vehicle’s Passive Entry RKE transmitthe light bar which is located on the deck lid above the ters is outside the vehicle and within 5 ft (1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Do NOT grab the door handle, when pushing the door handle button. This could unlock the door(s).
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: WINDOWS • After pushing the door handle button, you must wait Power Windows two seconds before you can lock or unlock the doors, The window controls on the driver’s door control both of using either Passive Entry door handle. This is done to the door windows. allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 There is a single window control on the passenger’s door trim panel that operates the window on the passenger’s door. The window controls will operate only when the ignition switch is in the ON/RUN or ACC position. NOTE: • The Key Off Power Delay feature will allow the power windows to operate for up to 10 minutes after the ignition is turned OFF. This feature is cancelled when either front door is opened. The time for this feature is programmable.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To open the window part way, push the window switch NOTE: The transmission must be in PARK before the to the first detent and release it when you want the button will operate. If equipped with a manual transmission, the vehicle speed must be under 5 mph (8 km/h) window to stop. before the button will operate. To stop the window from going all the way down during the AUTO-down operation, pull up on the switch briefly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 With the ignition switch in the ON/RUN position, the TRUNK SAFETY WARNING Trunk Open symbol will display in the instrument cluster indicating that the trunk is open. The odometer display WARNING! will reappear once the trunk is closed.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Trunk Emergency Release OCCUPANT RESTRAINT SYSTEMS As a security measure, a Trunk Internal Emergency Release lever is built into the trunk latching mechanism. In the event of an individual being locked inside the trunk, the trunk can be opened by activating the glow-in-the-dark handle attached to the trunk latching mechanism.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 2. If a child from 2 to 12 years old (not in a rear-facing 6. All occupants should always wear their lap and child restraint) must ride in the front passenger seat, shoulder belts properly. move the seat as far back as possible and use the 7. The driver and front passenger seats should be moved proper child restraint. (Refer to “Child Restraints”) back as far as practical to allow the Advanced Front 3.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Never place a rear-facing child restraint in front of an air bag. A deploying Passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rearfacing child restraint. • Only use rear-facing child restraint in a vehicle with a rear seat. from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Once the sequence starts, it will continue for the entire duration or until the respective seat belts are buckled. After the sequence completes, the Seat Belt Reminder Light remains illuminated until the respective seat belts are buckled. The driver should instruct all other occupants to buckle their seat belts.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wear your seat belt even though you have air bags. • In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 WARNING! (Continued) WARNING! (Continued) • A lap belt worn too high can increase the risk of injury in a collision. The seat belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt as low as possible and keep it snug. • A twisted seat belt may not protect you properly. In a collision, it could even cut into you. Be sure the seat belt is flat against your body, without twists.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. • A frayed or torn seat belt could rip apart in a collision and leave you with no protection. Inspect the seat belt system periodically, checking for cuts, frays, or loose parts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 2 Pulling Out The Latch Plate Inserting Latch Plate Into Buckle 3. When the seat belt is long enough to fit, insert the latch 4. Position the lap belt so that it is snug and lies low plate into the buckle until you hear a “click.” across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the seat belt, push the red button on the buckle. The seat belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the seat belt to retract fully. Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: These devices are not a substitute for proper seat We recommend that pregnant women use the seat belts belt placement by the occupant. The seat belt still must be throughout their pregnancy. Keeping the mother safe is worn snugly and positioned properly. The pretensioners are triggered by the Occupant Rethe best way to keep the baby safe. straint Controller (ORC).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 For additional information, refer to “Installing Child Restraints Using The Vehicle Seat Belt” under the “Child Restraints” section of this manual. The table below defines the type of feature for each seating position. If the passenger seating position is equipped with an ALR and is being used for normal usage, only pull the seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the ALR.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Never place a rear-facing child restraint in front of an air bag. A deploying Passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rearfacing child restraint. • Only use rear-facing child restraint in a vehicle with a rear seat. How To Engage The Automatic Locking Mode 1. Buckle the combination lap and shoulder belt. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 WARNING! (Continued) • Do not use the Automatic Locking Mode to restrain occupants who are wearing the seat belt or children who are using booster seats. The locked mode is only used to install rear-facing or forward-facing child restraints that have a harness for restraining the child.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The passenger’s Advanced Front Air Bag is mounted in the instrument panel, above the glove compartment. The words “SRS AIRBAG” or “AIRBAG” are embossed on the air bag covers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 This vehicle may be equipped with a driver and/or front passenger seat belt buckle switch that detects whether The Advanced Front Air Bag system has multistage the driver or front passenger seat belt is buckled. The seat driver and front passenger air bags. This system provides belt buckle switch may adjust the inflation rate of the output appropriate to the severity and type of collision as Advanced Front Air Bags.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, air bags won’t deploy at all. Always wear your seat belts even though you have air bags. Advanced Front Air Bag Operation Advanced Front Air Bags are designed to provide additional protection by supplementing the seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 way as the air bags inflate to their full size. The Advanced Supplemental Side Air Bags Front Air Bags fully inflate in less time than it takes to Your vehicle is equipped with two types of side air bags: blink your eyes. The air bags then quickly deflate while 1. Supplemental Seat-Mounted Side Air Bags (SABs): helping to restrain the driver and front passenger. Located in the outboard side of the front seats.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The SABs may help to reduce the risk of occupant injury 2. Supplemental Side Air Bag Inflatable Curtains (SABICs): Located above the side windows. The trim during certain side impact and certain rollover events, in covering the SABICs is labeled “SRS AIRBAG” or “AIRaddition to the injury reduction potential provided by the BAG.” seat belts and body structure. When the SAB deploys, it opens the seam on the outboard side of the seatback’s trim cover.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 SABICs may help reduce the risk of head injury to front and rear seat outboard occupants. SABICs may reduce the risk of injuries in certain side impact and vehicle rollover events, in addition to the injury reduction potential provided by the seat belts and body structure. The SABICs deploy downward, covering the side windows. An inflating SABIC pushes the outside edge of the trim out of the way and covers the window.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The SABICs and SABs (“Side Air Bags”) are designed to activate in certain side impacts and certain rollover events. The Occupant Restraint Controller (“ORC”) determines whether the deployment of the Side Air Bags in a particular side impact or rollover event is appropriate, based on the severity and type of collision. Vehicle damage by itself is not a good indicator of whether or not Side Air Bags should have deployed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 WARNING! (Continued) • Relying on the Side Air Bags alone could lead to more severe injuries in a collision. The Side Air Bags work with your seat belt to restrain you properly. In some collisions, Side Air Bags won’t deploy at all. Always wear your seat belt even though you have Side Air Bags. Side Air Bags deploy independently; a left side impact deploys the left Side Air Bags only and a right side impact deploys the right Side Air Bags only.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Side Air Bags will not deploy in all rollover events. If you do have a collision, which deploys the air bags, any The rollover sensing-system determines if a rollover event or all of the following may occur: may be in progress and whether deployment is appropri• The air bag material may sometimes cause abrasions ate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 throat irritation, move to fresh air. If the irritation NOTE: continues, see your doctor. If these particles settle on • Air bag covers may not be obvious in the interior trim, your clothing, follow the garment manufacturer’s inbut they will open during air bag deployment. structions for cleaning. • After any collision, the vehicle should be taken to an Do not drive your vehicle after the air bags have deauthorized dealer immediately. ployed.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Turn on the interior lights, which remain on as long as The ORC monitors the readiness of the electronic parts of the battery has power or until the ignition is placed in the air bag system whenever the ignition is in the START or ON/RUN position. If the ignition is in the OFF the “OFF” position. position or in the ACC position, the air bag system is not • Unlock the doors automatically. on and the air bags will not inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 The ORC also includes diagnostics that will illuminate the instrument panel Air Bag Warning Light if a malfunction is detected that could affect the air bag system. The diagnostics also record the nature of the malfunction. While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the air bag system immediately.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Redundant Air Bag Warning Light If a fault with the Air Bag Warning Light is detected, which could affect the Supplemental Restraint System (“SRS”), the Redundant Air Bag Warning Light will illuminate on the instrument panel. The Redundant Air Bag Warning Light will stay on until the fault is cleared. In addition, a single chime will sound to alert you that the Redundant Air Bag Warning Light has come on and a fault has been detected.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 WARNING! (Continued) • Do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion, needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE These data can help provide a better understanding of Child Restraints the circumstances in which crashes and injuries occur. Everyone in your vehicle needs to be buckled up at all NOTE: EDR data are recorded by your vehicle only if a times, including babies and children.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 WARNING! (Continued) great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size. Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. You should also make sure that you can install it in the vehicle where you will use it.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight Or Age Infants and Toddlers Small Children Larger Children Children Too Large for Child Restraints Children who are two years old or younger and who have not reached the height or weight limits of their child restraint Children who are at least two years old or who have out-grown the height or weight limit of their rear-facing child restraint Children who have out-gr
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Infants And Child Restraints Safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear-facing: infant carriers and convertible child seats. The infant carrier is only used rear-facing in the vehicle.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat belts fit properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether the child can use the vehicle’s seat belt alone: 1. Can the child sit all the way back against the back of the vehicle seat? 2.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Recommendations For Attaching Child Restraints Restraint Type Combined Weight of the Child + Child Restraint Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Lower Anchors And Tethers For Children (LATCH) Restraint System Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCHequipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH Positions For Installing Child Restraints In This Vehicle • • Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the head restraints be removed? Yes The child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint owner’s manual for more information. Center only may be removed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Locating Tether Anchorages There are tether strap anchorages behind each rear seating position located in the panel between the rear seatback and the rear window. They are found under a plastic cover with the tether anchorage symbol on it. Tether Strap Anchorages LATCH-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Center Seat LATCH To Install A LATCH-Compatible Child Restraint If a child restraint installed in the center position blocks the seat belt webbing or buckle for the outboard position, do not use that outboard position. If a child seat in the center position blocks the outboard LATCH anchors or seat belt, do not install a child seat in that outboard position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 3. Attach the lower hooks or connectors of the child How To Stow An Unused ALR Seat Belt: restraint to the lower anchorages in the selected seat- When using the LATCH attaching system to install a ing position. child restraint, stow all ALR seat belts that are not being 4. If the child restraint has a tether strap, connect it to the used by other occupants or being used to secure child top tether anchorage. See the section “Installing Child restraints.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Installing Child Restraints Using The Vehicle Seat Belt • Improper installation of a child restraint to the LATCH anchorages can lead to failure of the restraint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • Child restraint anchorages are designed to withstand only those loads imposed by correctly-fitted child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Lap/Shoulder Belt Systems for Installing Child Restraints in this Vehicle 2 • ALR = Switchable Automatic Locking Retractor • Top Tether Anchorage Symbol
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE What is the weight limit (child’s weight + weight of the child restraint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? Weight limit of the Child Restraint Always use the tether anchor when using the seat belt to install a forward facing child restraint, up to the recommended weight limit of the child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 5. To lock the seat belt, pull down on the shoulder part of the seat belt until you have pulled all the seat belt webbing out of the retractor. Then, allow the webbing 1. Place the child seat in the center of the seating to retract back into the retractor. As the webbing position. For some second row seats, you may need to retracts, you will hear a clicking sound.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the seat belt path. It should not move more than 1 inch (25.4 mm) in any direction. Any seat belt system will loosen with time, so check the seat belt occasionally, and pull it tight if necessary.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another position in the vehicle if one is available. 2. Rotate or lift the cover to access the anchor directly behind the seat where you are placing the child restraint. 3.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Attach the tether strap hook of the child restraint to Transporting Pets the top tether anchorage as shown in the diagram. Air Bags deploying in the front seat could harm your pet. 5. Remove slack in the tether strap according to the child An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in restraint manufacturer’s instructions. a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. However, wide-open throttle acceleration in low gear can be detrimental and should be avoided. NOTE: A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication of difficulty.
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE It is recommended for the operator to observe the follow- 100 to 300 miles (161 to 483 km): ing driving behaviors during the new vehicle break-in • Push the accelerator pedal slowly and not more than period: halfway to avoid rapid acceleration in lower gears (1st to 3rd gears). 0 to 100 miles (0 to 161 km): • Do not allow the engine to operate at idle for an • extended period of time.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 For the first 1500 mi (2414 km): • Do not participate in track events, sport driving schools, or similar activities during the first 1500 mi (2414 km). NOTE: Check engine oil with every refueling and add if necessary. Oil and fuel consumption may be higher through the first oil change interval. SAFETY TIPS Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. WARNING! • Do not leave children or animals inside parked vehicles in hot weather.
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! (Continued) WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO), follow these safety tips: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 Safety Checks You Should Make Inside The Vehicle Seat Belts is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Inspect the seat belt system periodically, checking for Defroster cuts, frays, and loose parts. Damaged parts must be Check operation by selecting the defrost mode and place replaced immediately.
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury. • Always make sure that floor mats are properly attached to the floor mat fasteners. • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfering with the pedals or the ability to control the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 Periodic Safety Checks You Should Make Outside The Vehicle Door Latches Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks, and bulges. Check the wheel nuts for tightness. Check the tires (including spare) for proper cold inflation pressure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS ! MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 ! BLIND SPOT MONITORING (BSM) — IF EQUIPPED. . . . . . . . . . . . . . . . . . . . . . . ▫ Automatic Dimming Mirror — If Equipped . . .105 ▫ Rear Cross Path — If Equipped. . . . . . . . . ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . .111 ▫ Modes Of Operation . . . . . . . . . . . . . . . . ▫ Outside Mirrors Folding Feature . . . . . . . . . .112 ▫ General Information. . . .
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Manual Front Seatback Recline . . . . . . . . . . . .130 ▫ Passenger Seat Easy Entry . . . . . . . . . . . . . . .131 ▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . .132 ▫ Folding Rear Seat . . . . . . . . . . . . . . . . . . . . .134 ! TO OPEN AND CLOSE THE HOOD . . . . . . . . .136 ! LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138 ▫ Headlight Switch . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 ▫ Mist Feature . . . . . . . . . . . . . . . . . . . . . . . . .149 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . .157 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . .149 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . .157 ▫ Headlights On With Wipers (Available With Automatic Headlights Only) . . . . . . . . . . . . .150 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . .157 ▫ Rain Sensing Wipers — If Equipped .
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ To Vary The Speed Setting . . . . . . . . . . . . . . .167 ▫ Changing FCW Status . . . . . . . . . . . . . . . . . .187 ▫ Setting The Following Distance In ACC . . . . . .169 ▫ Service FCW Warning . . . . . . . . . . . . . . . . . .188 ▫ Overtake Aid . . . . . . . . . . . . . . . . . . . . . . . .173 ! PARKSENSE® REAR PARK ASSIST — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . ▫ Adaptive Cruise Control (ACC) Menu . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 ! OVERHEAD CONSOLE . . . . . . . . . . . . . . . . . .200 ! POWER SUNROOF — IF EQUIPPED . . . . . . . .210 ▫ Courtesy/Reading Lights . . . . . . . . . . . . . . .201 ▫ Opening Sunroof — Express . . . . . . . . . . . . . .211 ▫ Sunglasses Storage . . . . . . . . . . . . . . . . . . . .201 ▫ Opening Sunroof — Manual Mode . . . . . . . . .211 ! GARAGE DOOR OPENER — IF EQUIPPED . . .201 ▫ Closing Sunroof — Express. . . . . . . . . . . . . . .
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ! CUPHOLDERS . . . . . . . . . . . . . . . . . . . . . . . .217 ▫ Glove Compartment . . . . . . . . . . . . . . . . . . .218 ▫ Front Cupholders . . . . . . . . . . . . . . . . . . . . .217 ▫ Console Storage. . . . . . . . . . . . . . . . . . . . . . .219 ▫ Rear Cupholders . . . . . . . . . . . . . . . . . . . . .218 ! REAR WINDOW FEATURES . . . . . . . . . . . . . .220 ! STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 MIRRORS Automatic Dimming Mirror — If Equipped The Automatic Dimming Mirror feature can be turned On or Off through the touchscreen. • Press the Mirror Dimmer button once to turn the A single ball joint mirror is provided in the vehicle. It is feature On. a twist on mirror that has a fixed position at the windshield.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If equipped, the rearview mirror contains an ASSIST and • Uconnect® Access Customer Care – In-vehicle support a 9-1-1 button. for Uconnect® Access and Uconnect® Access Via Mobile features. NOTE: The ASSIST and 9–1–1 features operate through the Uconnect® Access service. These buttons will only • Vehicle Customer Care – Total support for all other operate as long as your Uconnect® Access service is vehicle issues. active.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 2. The LED light located between the Assist and 9-1-1 NOTE: Once a connection is made between the vehicle’s buttons on the Rearview Mirror will turn green once a 9-1-1 Call system and the 9-1-1 operator, the 9-1-1 operaconnection to a 9-1-1 operator has been made. tor may be able to open a voice connection with the vehicle to determine if additional help is needed. Once 3.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from a 9-1-1 operator. All occupants should exit the vehicle immediately and move to a safe location. • The 9-1-1 Call system is embedded into the vehicle’s electrical system. Do not add aftermarket electrical equipment to the vehicle’s electrical system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 9-1-1 Call System Limitations Vehicles sold in Canada and Mexico DO NOT have 9-1-1 Call system capabilities. 9-1-1 or other emergency line operators in Canada and Mexico may not answer or respond to 9-1-1 system calls.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Even if the 9-1-1 Call system is fully functional, factors • Equipment malfunction at the 9-1-1 operator facility. beyond Chrysler Group LLC’s control may prevent or • Operator error by the 9-1-1 operator. stop the 9-1-1 Call system operation. These include, but are not limited to, the following factors: • Wireless network congestion. • Delayed accessories mode is active. • The ignition is in the OFF position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 General Information Outside Mirrors This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors Folding Feature Power Mirrors The mirrors are equipped with a rotational hinge. The The power mirror controls are located on the driver-side mirrors have one detent (clockwise) towards the rear of door trim panel. the vehicle and three detent’s (counterclockwise) towards the front of the vehicle. Power Mirror Controls Folding Mirrors The power mirror controls consist of mirror select buttons and a four-way mirror control switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 a mirror, press either the L (left) or R (right) to select the Illuminated Vanity Mirrors mirror that you want to adjust. An illuminated vanity mirror is on the sun visor. To use NOTE: A light in the selected button will illuminate the mirror, rotate the sun visor downward and swing the indicating the mirror is activated and can be adjusted. mirror cover upward. The light turns on automatically.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE “Slide-On-Rod” And Extender Features Of Sun Visor To use the “Slide-On-Rod” feature of the sun visor, rotate the sun visor downward and swing the sun visor so it is parallel to the side window, grabbing the sun visor with your left hand pull rearwards until the sun visor is in the desired position. To use the extender feature of the sun visor, grab the extender which is located at the rear of the visor and pull rearward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 BLIND SPOT MONITORING (BSM) — IF EQUIPPED The Blind Spot Monitoring (BSM) system uses two radarbased sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.) that enter the blind spot zones from the rear/front/side of the vehicle.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Transmission Vehicles The BSM system sensors operate when the vehicle is in any forward gear or REVERSE and enters stand-by mode when the vehicle is in PARK. Manual Transmission Vehicles The BSM system sensors operate when the vehicle is in any gear and enters stand-by mode when the Park Brake is engaged, the vehicle is not in REVERSE, and the vehicle is stationary.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 bumper of the vehicle. The BSM system monitors the detection zones on both sides of the vehicle when the vehicle speed reaches approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas. NOTE: The area on the rear fascia where the radar sensors are located must remain free of snow, ice, and dirt/road contamination so that the BSM system can function properly.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Side Entering From The Rear Vehicles that move into your adjacent lanes from either Vehicles that come up from behind your vehicle on either side of the vehicle. side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Overtaking Traffic If you pass another vehicle slowly (with a relative speed of less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 10 mph (16 km/h), the warning light will not illuminate.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in berms, etc. However, occasionally the system may alert adjacent lanes. on such objects. This is normal operation and your vehicle does not require service.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 WARNING! (Continued) system is not designed to detect pedestrians, bicyclists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicle’s mirrors, glance over your shoulder, and use your turn signal before changing lanes. Failure to do so can result in serious injury or death.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When RCP is on and the vehicle is in REVERSE, the driver is alerted using both the visual and audible alarms, including reducing the radio volume.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 turn signal is then activated, and it corresponds to an Three selectable modes of operation are available in the alert present on that side of the vehicle, an audible chime Uconnect® System. Refer to “Uconnect® Settings” in will also be sounded. Whenever a turn signal and detected object are present on the same side at the same “Understanding Your Instrument Panel” for further intime, both the visual and audio alerts will be issued. In formation.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. The device must accept any interference received, including interference that may cause undesired opWhen the BSM system is turned off there will be no eration of the device. visual or audible alerts from either the BSM or RCP Changes or modifications to any of these systems by systems. other than an authorized service facility could void NOTE: The BSM system will store the current operating authorization to use this equipment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 WARNING! (Continued) • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. 3 Power Seats The power seat switches are located on the outboard side of the front seat cushions.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Push the switch rearward to decrease the lumbar support. Pushing upward or downward on the switch will The height of the seats can be adjusted up or down. Pull raise and lower the position of the support. upward or push downward on the seat switch, the seat will move in the direction of the switch. Release the switch when the desired position is reached.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 WARNING! CAUTION! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the HI-level setting is selected, the system will automatically switch to LO-level after approximately 60 minutes of continuous operation. At that time, the display will change from HI to LO, indicating the change. The LO-level setting will turn OFF automatically after approximately 45 minutes. NOTE: The engine must be running for the heated seats to operate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 NOTE: The engine must be running for the ventilated Located in the seat cushion and seat back are small fans seats to operate. that draw the air from the passenger compartment and Vehicles Equipped With Remote Start move air through fine perforations in the seat cover to help keep the driver and front passenger cooler in higher On models that are equipped with remote start, the ambient temperatures.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Forward Or Rearward Adjustment Manual Front Seatback Recline The adjusting bar is located at the front of the seat, near the floor. Pull the bar upward to move the seat forward or rearward. Release the bar once the seat is in the desired position. Using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. normal seating position, first return the seatback to its original recline location and then slide the entire seat back to the pre-set lock position.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Head Restraints Active Head Restraints — Front Seats Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. The front driver and passenger seats are equipped with Active Head Restraints (AHR).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 To raise the head restraint, pull upward on the head restraint. To lower the head restraint, push the adjustment button, located at the base of the head restraint and push downward on the head restraint. To remove the head restraint, remove the seat belt from the seat belt loop. Raise the head restraint as far as it can go then push the adjustment button and release button at the base of each post while pulling the head restraint up.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle. Always securely stow removed head restraints in a location outside the occupant compartment. • ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants. Follow the re-installation instructions above prior to operating the vehicle or occupying a seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 WARNING! Folded Rear Seat When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap. • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood. 2. Move to the outside of the vehicle, the safety catch is located under the center front edge of the hood. 1. Pull the hood release lever located under the left side of the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 3. Push the safety catch to the left. CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. WARNING! Hood Safety Catch Be sure the hood is fully latched before driving your vehicle.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Headlight Switch The headlight switch is located on the left side of the instrument panel. This switch controls the operation of the headlights, parking lights, instrument panel lights, instrument panel light dimming, interior lights and fog lights. Headlight Switch Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Automatic Headlights — If Equipped Headlights On With Wipers (Available With This system automatically turns the headlights on or off Automatic Headlights Only) according to ambient light levels. To turn the system on, When this feature is active, the headlights will turn on rotate the headlight switch counterclockwise to the after the wipers are turned on if the headlight switch is AUTO position.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film, The Automatic High Beam Headlamp Control system and other obstructions on the windshield or camera provides increased forward lighting at night by automatlens will cause the system to function improperly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 To Activate Headlight Time Delay 1. Turn the headlight switch to the AUTO headlight This feature provides the safety of headlight illumination for up to 90 seconds when leaving your vehicle in an position. unlit area. 2. Push the multifunction lever away from you (toward To activate the delay feature, turn OFF the ignition switch front of vehicle) to engage the high beam mode. while the headlights are still on.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Headlight Time Delay is programmable using Fog Lights — If Equipped the Uconnect® System, refer to “Uconnect® Settings” in The front fog light switch is built into the headlight “Understanding Your Instrument Panel” for further inforswitch. mation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 To activate the front fog lights, turn on the parking lights or the low beam headlights and press the headlight switch. To turn off the front fog lights, either press the headlight switch a second time or turn off the headlight switch. An indicator light in the instrument cluster illuminates when the fog lights are turned on. Multifunction Lever The multifunction lever controls the operation of the turn signals, headlight beam selection and passing lights.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals Lane Change Assist Move the multifunction lever up or down and the arrows Tap the lever up or down once, without moving beyond on each side of the instrument cluster flash to show the detent, and the turn signal (right or left) will flash proper operation of the front and rear turn signal lights. three times then automatically turn off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 NOTE: If the multifunction lever is held in the flash-to pass position for more than 20 seconds, the high beams will shut off. Map/Reading Lights 3 These lights are mounted between the sun visors on the overhead console. Each light is turned on by pressing the lens. Press the lens a second time to turn off the light.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights Dimmer Controls The interior lights come on when a door is opened. The dimmer control is part of the headlight switch and is located on the left side of the instrument panel. To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition is moved to the LOCK position. This will occur if the interior lights were switched on manually or are on because a door is open.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 With the parking lights or headlights on, rotating the left dimmer control upward will increase the brightness of the instrument panel lights and lighted cupholders (if equipped). Dome Light Position Rotate the left dimmer control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rotate the end of the multifunction lever to the first The multifunction lever operates the windshield detent past the intermittent settings for low-speed wiper wipers and washer when the ignition is placed in operation, or to the second detent past the intermittent settings for high-speed wiper operation. the ON/RUN or ACC position. The multifunction lever is located on the left side of the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 end of the lever to select the desired delay interval. There are four delay settings, which allow you to regulate the wipe interval from a minimum of one cycle every second to a maximum of approximately 36 seconds between cycles. The delay intervals will double in duration when the vehicle speed is 10 mph (16 km/h) or less.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 The sensitivity of the system can be adjusted with the multifunction lever. Wiper delay position 1 is the least sensitive, and wiper delay position 4 is the most sensitive. Setting 3 should be used for normal rain conditions. Settings 1 and 2 can be used if the driver desires less wiper sensitivity. Setting 4 can be used if the driver desires more sensitivity. Place the wiper switch in the OFF position when not using the system.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping lever is located below the steering wheel at the end of the steering column. To unlock the steering column, pull the lever downward. To tilt the steering column, move the steering wheel upward or downward as desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 POWER TILT/TELESCOPING STEERING COLUMN — IF EQUIPPED This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The power tilt/telescoping steering column lever is located below the multifunction lever on the steering column. Power Tilt/Telescoping Switch To tilt the steering column, move the lever up or down as desired.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE HEATED STEERING WHEEL — IF EQUIPPED Vehicles Equipped With Remote Start The steering wheel contains a heating element that helps warm your hands in cold weather. The heated steering wheel has only one temperature setting. Once the heated steering wheel has been turned on it will operate for up to 80 minutes before automatically shutting off. The heated steering wheel can shut off early or may not turn on when the steering wheel is already warm.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 WARNING! (Continued) • Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material. This may cause the steering wheel heater to overheat. 3 ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, the Electronic Speed Control takes over accelerator operations at speeds greater than 25 mph (40 km/h).
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “UnderA soft tap on the brake pedal, pushing the CANCEL standing Your Instrument Panel” for more information. button, or normal brake pressure while slowing the The speed increment shown is dependant on the chosen vehicle will deactivate the Electronic Speed Control withspeed unit of U.S. (mph) or Metric (km/h): out erasing the set speed from memory.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Metric Speed (km/h) The speed decrement shown is dependant on the chosen speed unit of U.S. (mph) or Metric (km/h): • Pressing the SET + button once will result in a 1 km/h increase in set speed. Each subsequent tap of the U.S. Speed (mph) button results in an increase of 1 km/h. • Pressing the SET - button once will result in a 1 mph • If the button is continually pressed, the set speed will decrease in set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 To Accelerate For Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control On Hills The transmission may downshift on hills to maintain the vehicle set speed. WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control and have an accident.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ACC will allow you to keep cruise control engaged in The Cruise Control system has two control modes: light to moderate traffic conditions without the constant • Adaptive Cruise Control mode for maintaining an need to reset your cruise control. ACC utilizes a radar appropriate distance between vehicles. sensor designed to detect a vehicle directly ahead of you. • Normal (fixed speed) cruise control mode is for cruisNOTE: ing at a constant preset speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 WARNING! WARNING! (Continued) • Adaptive Cruise Control (ACC) is a convenience system. It is not a substitute for active driving involvement. It is always the driver’s responsibility to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead; and, most importantly, brake operation to ensure safe operation of the vehicle under all road conditions.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • When circumstances do not allow safe driving at a constant speed. Adaptive Cruise Control (ACC) Operation The speed control buttons (located on the right side of the steering wheel) operates the ACC system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 NOTE: Any chassis/suspension or tire size modifications When the system is OFF, the DID displays “Adaptive to the vehicle will effect the performance of the Adaptive Cruise Control (ACC) Off.” Cruise Control and Forward Collision Warning System. NOTE: You cannot engage ACC under the following conditions: Activating Adaptive Cruise Control (ACC) You can only engage ACC if the vehicle speed is above • When you apply the brakes. 20 mph (32 km/h).
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To turn the system OFF, push and release the Adaptive Push and release the Adaptive Cruise Control (ACC) Cruise Control (ACC) ON/OFF button again. At this ON/OFF button. The ACC menu in the DID displays time, the system will turn off and the DID will display “Adaptive Cruise Control (ACC) Off.” “ACC Ready.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 WARNING! Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have a collision. Always leave the system off when you are not using it. To Set A Desired ACC Speed Remove your foot from the accelerator pedal. If you do not, the vehicle may continue to accelerate beyond the set speed.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The shift lever/gear selector is removed from the To Resume Drive position. If there is a set speed in memory press the RES (resume) • The Electronic Stability Control/Traction Control Sys- button and then remove your foot from the accelerator pedal. The DID will display the last set speed. tem (ESC/TCS) activates. • The vehicle parking brake is applied. • A Trailer Sway Control (TSC) event occurs. • The driver switches ESC to full-off mode.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 To Vary The Speed Setting Metric Speed (km/h) To Increase Speed • Pressing the SET + button once will result in a 1 km/h increase in set speed. Each subsequent tap of the While ACC is set, you can increase the set speed by button results in an increase of 1 km/h. pressing the SET + button.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The speed decrement shown is dependant on the chosen • If the button is continually pressed, the set speed will speed unit of U.S. (mph) or Metric (km/h): continue to decrease in 10 km/h increments until the button is released. The decrease in set speed is reU.S. Speed (mph) flected in the DID. • Pressing the SET - button once will result in a 1 mph NOTE: decrease in set speed. Each subsequent tap of the button results in a decrease of 1 mph.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 • The ACC system maintains set speed when driving up hill and down hill. However, a slight speed change on moderate hills is normal. In addition, downshifting may occur while climbing uphill or descending downhill. This is normal operation and necessary to maintain set speed. When driving up hill and down hill, the ACC system will cancel if the braking temperature exceeds normal range (overheated).
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Distance Setting 3 Bars (Long) Distance Setting 2 Bars (Medium)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 To increase the distance setting, press the Distance Setting — Increase button and release. Each time the button is pressed, the distance setting increases by one bar (longer). To decrease the distance setting, press the Distance Setting — Decrease button and release. Each time the button is pressed, the distance setting decreases by one bar (shorter). Distance Setting 1 Bar (Short) If there is no vehicle ahead, the vehicle will maintain the set speed.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The vehicle will then maintain the set distance until: A Proximity Warning will alert the driver if ACC predicts that its maximum braking level is not sufficient to • The vehicle ahead accelerates to a speed above the set maintain the set distance. If this occurs, a visual alert speed. “BRAKE” will flash in the DID and a chime will sound • The vehicle ahead moves out of your lane or view of while ACC continues to apply its maximum braking capacity.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 NOTE: The “Brake!” Screen in the DID is a warning for the driver to take action and does not necessarily mean that the Forward Collision Warning system is applying the brakes autonomously. Overtake Aid Adaptive Cruise Control (ACC) Menu The DID displays the current ACC system settings. The DID is located in the center of the instrument cluster. The information it displays depends on ACC system status.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the SET + or the SET- button (located on the Display Warnings And Maintenance steering wheel) and the following will display in the DID: “Wipe Front Radar Sensor In Front Of Vehicle” ACC SET Warning When ACC is set, the set speed will display in the The “ACC/FCW Unavailable Wipe Front Radar Sensor” warning will display and also a chime will indicate when instrument cluster. conditions temporarily limit system performance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 vehicle has left these areas. Under rare conditions, when • Do not remove any screws from the sensor. Doing so the radar is not tracking any vehicles or objects in its path could cause an ACC system malfunction or failure and this warning may temporarily occur. require a sensor realignment.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If this occurs, try activating ACC again later, following an ignition cycle. If the problem persists, see your autho• If the “ACC/FCW Unavailable Wipe Front Radar rized dealer. Sensor” message occurs frequently (e.g. more than once on every trip) without any snow, rain, mud, or Precautions While Driving With ACC other obstruction, have the radar sensor realigned at In certain driving situations, ACC may have detection your authorized dealer. issues.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 the vehicle is out of the curve the system will resume your original Set Speed. This is a part of normal ACC system functionality. NOTE: On tight turns ACC performance may be limited. Offset Driving Condition Example Turns And Bends When driving on a curve with ACC engaged, the system may decrease the vehicle speed and acceleration for stability reasons, with no target vehicle detected.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using ACC On Hills Lane Changing When driving on hills, ACC may not detect a vehicle in your lane. Depending on the speed, vehicle load, traffic conditions, and the steepness of the hills, ACC performance may be limited. ACC may not detect a vehicle until it is completely in the lane in which you are traveling.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 Narrow Vehicles Some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There may not be sufficient distance to the vehicle ahead.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Stationary Objects And Vehicles General Information ACC does not react to stationary objects and stationary vehicles. For example, ACC will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane. Always be attentive and ready to apply the brakes if necessary.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 Normal (Fixed Speed) Electronic Speed Control Mode In addition to Adaptive Cruise Control mode, a Normal (Fixed Speed) Electronic Speed Control mode is available for cruising at fixed speeds. The Normal (Fixed Speed) Electronic Speed Control mode is designed to maintain a set cruising speed without requiring the driver to operate the accelerator. Electronic Speed Control can only be operated if the vehicle speed is above 20 mph (32 km/h).
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Once a speed has been set a message (CRUISE CON- The speed increment shown is dependant on the speed of TROL SET TO MPH/KM) will appear indicating what U.S. (mph) or Metric (km/h) units: speed was set. This light will turn on when the electronic U.S. Speed (mph) speed control is SET. • Pressing the SET + button once will result in a 1 mph To Vary The Speed Setting increase in set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 • If the button is continually pressed, the set speed will • If the button is continually pressed, the set speed will continue to increase in 10 km/h increments until the continue to decrease in 5 mph decrements until the button is released. The increase in set speed is reflected button is released. The decrease in set speed is rein the DID display. flected in the DID display.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Cancel To Resume Speed The following conditions will cancel the Normal (Fixed To resume a previously set speed, push the RES button Speed) Electronic Speed Control without clearing the and release. Resume can be used at any speed above memory: 20 mph (32 km/h). • The brake pedal is applied. • The CANCEL button is pressed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 FORWARD COLLISION WARNING (FCW) — IF EQUIPPED Forward Collision Warning (FCW) Operation The Forward Collision Warning (FCW) system provides the driver with audible warnings, visual warnings (within the DID), to warn the driver when it detects a potential frontal collision. The warnings are intended to provide the driver with enough time to react, avoid or mitigate the potential collision.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • The minimum speed for FCW activation is 5 mph (10 km/h). WARNING! (Continued) responsibility to avoid a collision by controlling the vehicle via braking and steering. Failure to follow this warning could lead to serious injury or death. • The FCW alerts may be triggered on objects other than vehicles such as guard rails or sign posts based on the course prediction.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Changing the FCW status to “Off” prevents the system Changing the FCW status to the “Near” setting, allows from warning you of a possible collision with the vehicle the system to warn you of a possible collision with the vehicle in front of you when you are much closer. This in front of you. setting provides less reaction time than the “Far” setting, NOTE: The FCW system state is kept in memory from which allows for a more dynamic driving experience.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Service FCW Warning If the system turns off, and the DID displays: • ACC/FCW Unavailable Service Required ParkSense® will retain the last system state (enabled or disabled) from the last ignition cycle when the ignition is changed to the ON/RUN position. ParkSense® can be active only when the shift lever is in REVERSE. If ParkSense® is enabled at this shift lever This indicates there is an internal system fault.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 The system will indicate a detected obstacle by showing a single arc in one or more regions based on the obstacle’s The ParkSense® Warning screen will only be displayed if distance and location relative to the vehicle. Sound and Display is selected from the Uconnect® System.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Single 1/2 Second Tone/Solid Arc Slow Tone/Solid Arc
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 3 Fast Tone/Flashing Arc Continuous Tone/Flashing Arc
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 Arc — Left Rear Arc — Center Rear Arc — Right Rear Radio Volume Reduced WARNING ALERTS None None None None None None 6th Solid 5th Solid 4th Solid 3rd Flashing None None None None None No Yes Yes Yes Yes 2nd Flashing 2nd Flashing 2nd Flashing Yes 1st Flashing 1st Flashing 1st Flashing Yes 3
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the ParkSense® system is disabled, the Drivers Information Display (DID) will display ParkSense® can be enabled and disabled with the the “PARKSENSE OFF” message for approxiParkSense® switch, located on the switch panel below mately five seconds. Refer to “Drivers Informathe Uconnect® display. tion Display (DID)” in “Understanding Your Instrument Panel” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 Service The ParkSense® Rear Park Assist System During vehicle start up, when the ParkSense® Rear Park Assist System has detected a faulted condition, the instrument cluster will actuate a single chime, once per ignition cycle and it will display the “PARKSENSE UNAVAILABLE WIPE REAR SENSORS” or “PARKSENSE UNAVAILABLE SERVICE REQUIRED” message for five seconds.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense® System Usage Precautions NOTE: • ParkSense® will reduce the volume of the radio when it is sounding an audio tone. • Clean the ParkSense® sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not working • Jackhammers, large trucks, and other vibrations could properly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 CAUTION! WARNING! • ParkSense® is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using ParkSense® in order to be able to stop in time when an obstacle is detected.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKVIEW® REAR BACK UP CAMERA — IF EQUIPPED If your vehicle is equipped with the Camera Delay feature and it is turned ON, the rear camera image will be displayed for up to 10 seconds when the vehicle is shifted out of REVERSE unless the forward vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into #PARK# or the vehicle’s ignition is cycled to the OFF position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 Different colored zones indicate the distance to the rear of The following table shows the approximate distances for the vehicle. each zone: Zone Red Yellow Green Distance to the rear of the vehicle 0 - 1 ft (0 - 30 cm) 1 ft - 6.5 ft (30 cm - 2 m) 6.5 ft or greater (2 m or greater) 3 WARNING! CAUTION! Drivers must be careful when backing up even when using the ParkView® Rear Back Up Camera.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • To avoid vehicle damage, the vehicle must be driven slowly when using ParkView® to be able to stop in time when an obstacle is seen. It is recommended that the driver look frequently over his/her shoulder when using ParkView®. OVERHEAD CONSOLE The overhead console contains courtesy/reading lights and sunglass storage. Universal Garage Door Opener (HomeLink®) button and a power sunroof switch may also be included, if equipped.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 Courtesy/Reading Lights Sunglasses Storage At the forward end of the overhead console are two At the rear of the console, a compartment is provided for courtesy/reading lights. the storage of a pair of sunglasses. Press the lens to turn on the light. Press it a second time The storage compartment access is a #push/push# design. to turn off the light. Push on the raised bar on the compartment door to open. Push on the raised bar to close.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink® buttons that are located in the overhead Before You Begin Programming HomeLink® console designate the three different HomeLink® chan- Be sure that your vehicle is parked outside of the garage nels. The HomeLink® indicator is located on the left side before you begin programming. of the first button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 NOTE: • Erasing all channels should only be performed when programming HomeLink® for the first time. Do not erase channels when programming additional buttons. • If you have any problems, or require assistance, please call toll-free 1-800-355-3515 or, on the Internet at HomeLink.com for information or assistance. Programming A Rolling Code For programming garage door openers that were manufactured after 1995.
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Place the ignition in the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view. 5. At the garage door opener motor (in the garage), locate the “LEARN” or “TRAINING” button. This can usually be found where the hanging antenna wire is attached to the garage door opener/device motor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 To program the remaining two HomeLink® buttons, Programming A Non-Rolling Code repeat each step for each remaining button. DO NOT For programming Garage Door Openers manufactured erase the channels. before 1995. Reprogramming A Single HomeLink® Button 1. Place the ignition in the ON/RUN position. (Rolling Code) To reprogram a channel that has been previously trained, 2.
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Push and hold the programmed HomeLink® button and observe the indicator light. • If the indicator light stays on constantly, programming is complete and the garage door/device should activate when the HomeLink® button is pushed. • To program the two remaining HomeLink® buttons, repeat each step for each remaining button. DO NOT erase the channels. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 It may be helpful to unplug the device during the cycling 4. Watch for the HomeLink® indicator to change flash rates. When it changes, it is programmed. It may take process to prevent possible overheating of the garage up to 30 seconds or longer in rare cases. The garage door or gate motor. door may open and close while you are programming. 1. Cycle the ignition to the ON/RUN position. 5. Push and hold the programmed HomeLink® button 2.
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming A Single HomeLink® Button (Canadian/Gate Operator) system, entry door lock, home/office lighting, etc.,). The hand-held transmitter of the device may also be used at any time. To reprogram a channel that has been previously trained, follow these steps: Security 1. Cycle the ignition to the ON/RUN position. It is advised to erase all channels before you sell or turn in your vehicle. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 Troubleshooting Tips If you are having trouble programming HomeLink®, here are some of the most common solutions: • Replace the battery in the original hand-held transmitter. • Push the LEARN button on the Garage Door Opener to complete the training for a Rolling Code.
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information POWER SUNROOF — IF EQUIPPED This device complies with FCC rules Part 15 and Industry The power sunroof switch is located between the sun Canada RSS-210. Operation is subject to the following visors on the overhead console. two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 WARNING! WARNING! (Continued) • Never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the Key Fob in or near the vehicle, or in a location accessible to children. Do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/RUN mode. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch.
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE movement. The sunroof and sunshade will remain in a Pinch Protect Feature partially opened condition until the switch is pushed and This feature will detect an obstruction in the opening of held rearward again. the sunroof during Express Close operation. If an obstruction in the path of the sunroof is detected, the Closing Sunroof — Express sunroof will automatically retract.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 Sunshade Operation Sunroof Maintenance The sunshade can be opened manually. However, the Use only a nonabrasive cleaner and a soft cloth to clean sunshade will open automatically as the sunroof opens. the glass panel. NOTE: The sunshade cannot be closed if the sunroof is Ignition Off Operation open. The power sunroof switch will remain active for up to approximately ten minutes after the ignition switch is Wind Buffeting turned to the LOCK position.
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS Your vehicle is equipped with two 12 Volt (13 Amp) power outlets that can be used to power cellular phones, small electronics and other low powered electrical accessories. The 12 Volt power outlets have power available at all times. These power outlets can also operate a conventional cigar lighter unit. NOTE: To ensure proper operation, a MOPAR® cigar knob and element must be used.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 3 Power Outlet — Center Console Power Outlet Fuse Locations NOTE: All accessories connected to these powered out- 1 — #12 Fuse 20A Yellow Power Outlet Integrated Center Stack lets should be removed or turned off when the vehicle is 2 — #38 Fuse 20A Yellow Power Outlet Center Console not in use to protect the battery against discharge.
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! (Continued) • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 CAUTION! (Continued) • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly. Only use these intermittently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle’s battery.
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Cupholders STORAGE The rear seat cupholders are located in the center armrest Glove Compartment between the rear seats. The cupholders are positioned The glove compartment is located on the passenger side forward in the armrest and side-by-side to provide conveof the instrument panel. nient access to beverage cans or bottles while maintaining a resting place for the rear occupant’s elbows.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 may also be equipped with a Universal Consumer Interface (UCI). UCI supports Mini, 4G, Photo, Nano, 5G iPod® and iPhone® devices. Refer to “Universal Consumer Interface (UCI) — If Equipped” in “Understanding Your Instrument Panel” for further information. Opened Glove Compartment Console Storage The center console has a storage compartment located underneath the armrest.
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not operate this vehicle with a console compartment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located on the climate control (Mode) knob. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped).
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS ! INSTRUMENT PANEL FEATURES . . . . . . . . . .224 ! Uconnect® SETTINGS . . . . . . . . . . . . . . . . . . .258 ! INSTRUMENT CLUSTER — BASE . . . . . . . . . .225 ▫ Buttons On The Faceplate. . . . . . . . . . . . . . . .259 ! INSTRUMENT CLUSTER — PREMIUM . . . . . .226 ▫ Buttons On The Touchscreen. . . . . . . . . . . . . .260 ! INSTRUMENT CLUSTER DESCRIPTIONS . . . . .227 ▫ Customer Programmable Features — Uconnect® 5.0 Settings . . . . . . . . . . . . . .
222 UNDERSTANDING YOUR INSTRUMENT PANEL ! iPod®/USB/MP3 CONTROL — IF EQUIPPED . .322 ! Uconnect® VOICE RECOGNITION QUICK TIPS . . . . . . . . . . . . . . . . . . . . . . . . . .339 ! STEERING WHEEL AUDIO CONTROLS — ▫ Introducing Uconnect® . . . . . . . . . . . . . . . . .339 IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .323 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . .324 ▫ Get Started . . . . . . . . . . . . . . . . . . . . . . . . . .340 ▫ Media Mode . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 223 ▫ Mobile App (8.4A/8.4AN) . . . . . . . . . . . . . . .349 ▫ SiriusXM Travel Link™ (8.4A/8.4AN) . . . . . . .352 ▫ Voice Texting (8.4A/8.4AN) . . . . . . . . . . . . . .350 ▫ Additional Information . . . . . . . . . . . . . . . . .353 ▫ Yelp® (8.4A/8.4AN). . . . . . . . . . . . . . . . . . . .
224 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 2 3 4 — Air Outlets — Instrument Cluster — Glove Box — Media Center 5 — Keyless Start/Stop Button 6 — Trunk Release Button 7 — Headlight Switch
UNDERSTANDING YOUR INSTRUMENT PANEL 225 INSTRUMENT CLUSTER — BASE 4 Instrument Cluster For 3.6L or 5.
226 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — PREMIUM Instrument Cluster For 6.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the MIL after 1. Tachometer engine start. The vehicle should be serviced if the MIL The red segments indicate the maximum permissible stays on through several of your typical driving cycles. In engine revolutions per minute (RPM x 1000) for each gear most situations, the vehicle will drive normally and will range.
228 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to the driver, occupants or others. 3. Vehicle Security Light — If Equipped 4.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock Brakes.
230 UNDERSTANDING YOUR INSTRUMENT PANEL 7. Gear Status Indicator — Automatic Transmission Only The Gear Status Indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. 8. Seat Belt Reminder Light This light will turn on for four to eight seconds as a bulb check when the ignition switch is first placed in ON/RUN. A chime will sound if the driver’s seat belt is unbuckled during the bulb check.
UNDERSTANDING YOUR INSTRUMENT PANEL 231 The light will remain on until the cause is corrected. NOTE: The light may flash momentarily during sharp cornering maneuvers which change fluid level conditions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is necessary. WARNING! Driving a vehicle with the brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle.
232 UNDERSTANDING YOUR INSTRUMENT PANEL 10. Air Bag Warning Light 13. High Beam Indicator This light will turn on for four to eight seconds This indicator will turn on when the high beam as a bulb check when the ignition switch is first headlights are on. Push the multifunction lever turned to the ON/RUN position. If the light is away from the steering wheel to switch the headlights to either not on during starting, stays on, or turns high beam.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 16. Temperature Gauge CAUTION! (Continued) The temperature gauge shows engine coolant temperature. Any reading within the normal range for a fully warm vehicle should be 200 F - 230 F which indicates that the engine cooling system is operating satisfactorily. drops back into the normal range. If the pointer remains on the “H,” and you hear a chime, turn the engine OFF immediately and call for service.
234 UNDERSTANDING YOUR INSTRUMENT PANEL 17. Tire Pressure Monitoring Telltale Light Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires).
UNDERSTANDING YOUR INSTRUMENT PANEL 235 of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. CAUTION! The TPMS has been optimized for the original equipment tires and wheels.
236 UNDERSTANDING YOUR INSTRUMENT PANEL 19. Electronic Stability Control (ESC) Activation/Malfunction Indicator Light — If Equipped The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON/RUN position. It should go out with the engine running. If the “ESC Activation/Malfunction Indicator Light” comes on continuously with the engine running, a malfunction has been detected in the ESC system.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 This system conveniently allows the driver to select a The Driver Information Display (DID) features an inter- variety of useful information by pushing the arrow active display which is located in the instrument cluster. buttons located on the left side of the steering wheel.
238 UNDERSTANDING YOUR INSTRUMENT PANEL • Diagnostics — If Equipped • Performance Shift Indicator (PSI) — If Equipped The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: Up And Down Arrow Buttons: Using the Up or Down arrows allows you to cycle through the Main Menu Items. Changes the Main Screen area and Menu Title area.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 NOTE: For Screen Setup and Vehicle Settings: • Holding the Up/Down or Left/Right arrow buttons • OK button allows user to enter menu and submenus. will loop the user through the currently selected menu • Within each submenu layer, the up/down arrows will or options presented on the screen. allow the user to select the item of interest. • Main menu and submenu’s wrap for continuous • Pushing the OK button makes the selection and a scrolling.
240 UNDERSTANDING YOUR INSTRUMENT PANEL Engine Oil Life Reset Oil Change Required Vehicles Equipped With Keyless Enter-N-Go™ 1. Without pushing the brake pedal, push the ENGINE START/STOP button and place the ignition to the Your vehicle is equipped with an engine oil change ON/RUN position (do not start the engine). indicator system. The “Oil Change Required” message will display in the DID for five seconds after a single 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 Secondary Method Of Navigating To The Oil Life Screen In The DID And Holding Ok 3. Push and release the RIGHT arrow button to access the ”Oil Life” screen. Your vehicle is equipped with an engine oil change 4. Push and hold the OK button until the “ Oil Life” indicator system. The “Oil Change Required” message screen displays. will flash in the DID display for approximately 10 seconds after a single chime has sounded to indicate the next 5.
242 UNDERSTANDING YOUR INSTRUMENT PANEL Cruise Control DID Yellow Telltales This area will show reconfigurable white caution tell- This area will show reconfigurable amber caution telltales. These telltales include: tales. These telltales include: • Cruise Ready This telltale will illuminate white to indicate that the Adaptive Cruise Control system is activated.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 • Service Adaptive Cruise Control — If Equipped This light will turn on when a ACC is not operating and needs service. For further information, refer to “Adaptive Cruise Control (ACC)” in “Understanding The Features Of Your Vehicle.” DID Red Telltales This area will show reconfigurable red caution telltales.
244 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • Even if power steering assistance is no longer operational, it is still possible to steer the vehicle. Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers. • Oil Pressure Warning Light This light indicates low engine oil pressure. The light should turn on momentarily when the engine is started.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system. OBTAIN SERVICE IMMEDIATELY. See an authorized dealer. If the light remains lit with the engine running, your vehicle will usually be drivable. However, see an authorized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required.
246 UNDERSTANDING YOUR INSTRUMENT PANEL on while driving, have the system inspected at an authorized dealer as soon as possible. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further information. • Speed Limit Warning Light Push and release the UP or DOWN arrow button until the Speed Limit Warning Menu icon/title is highlighted in the DID. Push and release OK to enter speed warning.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 DID Selectable Menu Items Trans Temp Push and release the UP or DOWN arrow buttons until Oil Temp the desired Selectable Menu item is displayed in the DID. Oil Pressure Follow the Menu or submenu prompts as desired. Oil Life Speedometer Battery Voltage Push and release the LEFT or RIGHT arrow button to Intake Air Temp toggle between the Speedometer display type.
248 UNDERSTANDING YOUR INSTRUMENT PANEL Performance Features WARNING! Measurement of vehicle statistics with the Performance Features is intended for off-highway or offroad use only and should not be done on any public roadways. It is recommended that these features be used in a controlled environment and within the limits of the law.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 • 1/8 Mile (200 meters)Timer – Best – Last – Current – Reaction Timer • 1/4 Mile (400 meters)Timer – Best – Last – Current – Reaction Timer • Braking Distance – Distance – From Speed • Current G-Forces • Peak G-Forces • Lap Timer • Lap History – Will list the last 5 lap with the best lap highlighted in green.
250 UNDERSTANDING YOUR INSTRUMENT PANEL The following describes each feature and its operation: 0 to 100 mph (0 to 161 km/h) When selected, this screen displays the time it takes for the vehicle to go from 0 to 100 mph (0 to 161 km/h) When selected, this screen displays the time it takes for within 20 seconds. the vehicle to go from 0 to 60 mph (0 to 100 km/h) within 10 seconds. • The feature will “ready” when the vehicle speed is at 0 mph (0 km/h).
UNDERSTANDING YOUR INSTRUMENT PANEL 251 1/8 Mile (200 Meters) 1/4 Mile (400 Meters) When selected, this screen displays the time it takes the When selected, this screen displays the time it takes the vehicle to travel 1/8 mile within 15 seconds and the vehicle to travel 1/4 mile within 25 seconds and the vehicle’s speed when it reaches 1/8 mile. vehicle’s speed when it reaches 1/4 mile (200 meters).
252 UNDERSTANDING YOUR INSTRUMENT PANEL Braking Distance Current G-Force When selected, this screen displays the vehicle’s braking When selected, this screen displays the current G-Force distance, and the speed at which the brake pedal was (lateral and longitudinal) that displays the directions of depressed. the forces. • This feature will only function when applying the Peak G-Force brakes at speeds above 30 mph (48 km/h).
UNDERSTANDING YOUR INSTRUMENT PANEL 253 • Each time the driver pushes OK for a Lap that current time populates, the Last time and also populates the When selected, the Lap Timer page will show the timer 1st (top) space on the Timer History page the current always at 0:00.00 with the previous Best and Last time time resets to 0:00.0 at every push of the OK button. data (unless the driver has cleared it via hold to Reset).
254 UNDERSTANDING YOUR INSTRUMENT PANEL • Holding the OK button only resets the page you are on. Push the ADAPTIVE CRUISE CONTROL (ACC) ON/ OFF button (located on the steering wheel) until one of • Lap History page is a static display of lap times only. the following displays in the DID: Top Speed Adaptive Cruise Control Off When selected, this screen displays the Top Speed since When ACC is deactivated, the display will read “Adaplast reset: tive Cruise Control Off.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 The ACC screen may display once again if any ACC LaneSense — If Equipped activity occurs, which may include any of the following: The DID displays the current LaneSense system settings. • Distance Setting Change The information displayed depends on LaneSense system status and the conditions that need to be met. For • System Cancel further information, refer to “LaneSense — If Equipped” • Driver Override in “Understanding The Features Of Your Vehicle.
256 UNDERSTANDING YOUR INSTRUMENT PANEL • Lower end of gauge will be displayed in an amber Audio color and turn green as Fuel Economy improves. Push and release the UP or DOWN arrow button until • MPG will have the gauge fill from the left (clockwise). the Audio Menu displays in the DID. • L/100 km will have the gauge fill from the right Stored Messages (counter clockwise). Push and release the UP or DOWN arrow button until • Hold OK to reset average fuel economy information.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 • If the menu is exited before the end of codes is reached - when the driver re-enters the list will be restarted Push and release the UP or DOWN arrow button until from the beginning. the diagnostic Menu is selected. Then, the Driver is able to view engine and emission vehicle faults. • When no codes are present or the last code is reached = (P0000) and this message is displayed: • Push OK to have the most recent fault code sent.
258 UNDERSTANDING YOUR INSTRUMENT PANEL The PSI indicator in the DID display remains illuminated until the driver changes gear, or the driving conditions return to a situation where changing gear is not required, corresponding to the configured RPMs in the head unit. Uconnect® SETTINGS The Uconnect® system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel that allows you to access and change the customer programmable features.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 Buttons On The Faceplate Buttons on the faceplate are located below the Uconnect® system in the center of the instrument panel. In addition, there is a Scroll/Enter control knob located on the right side. Turn the control knob to scroll through menus and change settings (i.e., 30, 60, 90), push the center of the control knob one or more times to select or change a setting (i.e., ON, OFF).
260 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Only one touchscreen area may be selected at a Buttons On The Touchscreen Buttons on the touchscreen are accessible on the Uconnect® time. display. When making a selection, press the button on the touchscreen to enter the desired mode. Once in the desired Customer Programmable Features — Uconnect® mode, select the preferred setting. Once the setting is 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 261 Display • Touchscreen Beep After pressing the “Display” button on the touchscreen When in this display, you may turn on or shut off the sound the following settings will be available: heard when a touchscreen button is pressed. To change the Mode status, press and release the “On” or “Off” button on • Display Mode the touchscreen.
262 UNDERSTANDING YOUR INSTRUMENT PANEL • Fuel Consumption Voice Select from: “psi,” “kPa,” or “bar.” When in this display, you may change the Voice Response Length settings. To change mode status, press and release the “Brief” or “Long” button on the touchscreen. Press the back arrow/Done button on the touchscreen to return to the previous menu. Select from: “MPG” (US), “MPG” (UK), “L/100 km” or After pressing the “Voice” button on the touchscreen the following settings will be available: “km/L.
UNDERSTANDING YOUR INSTRUMENT PANEL 263 Clock & Date • Set Date After pressing the “Clock & Date” button on the touch- When in this display, you may set the date manually. screen the following settings will be available: Press the “Set Date” button on the touchscreen then press the corresponding arrows above and below the current • Set Time date to adjust. Press the back arrow button/Done on the When in this display, you may set the time and format touchscreen to return to the previous menu. manually.
264 UNDERSTANDING YOUR INSTRUMENT PANEL the setting for more dynamic driving, select the Near setting. This warns you of a possible collision when you are much closer to the vehicle in front of you. To change the FCW status, press and release the “Near” or “Far” button. Press the back arrow/Done button on the touchscreen to return to the previous menu. effort. Press the “Comfort” button on the touchscreen to provide a balance of steering feel and steering effort.
UNDERSTANDING YOUR INSTRUMENT PANEL 265 • Rear ParkSense® Chime Volume Lights & Chime mode is activated, the Blind Spot Monitor (BSM) will show a visual alert in the exterior mirrors as well as an audible alert when the turn signal is on. When Off is selected, the Blind Spot Monitor (BSM) system is deactivated. To change the Blind Spot Alert status, press the “Off,” “Lights,” or “Lights & Chime” button on the touchscreen. Then press the back arrow/ Done button on the touchscreen.
266 UNDERSTANDING YOUR INSTRUMENT PANEL display whenever the shift lever/gear selector is put into REVERSE. The image will be displayed on the radio touchscreen display along with a caution note to “check entire surroundings” across the top of the screen. After five seconds, this note will disappear. To enable or disable, press the “ParkView® Backup Camera Active Guidelines” button on the touchscreen, and select “On” or “Off.
UNDERSTANDING YOUR INSTRUMENT PANEL 267 and operating information. To enable or disable, press the • Headlight Illumination On Approach “Hill Start Assist” button on the touchscreen, and select When this feature is selected, it allows the adjustment of “On” or “Off.” Press the back arrow/Done button on the the amount of time the headlights remain on when the touchscreen to return to the previous menu. doors are unlocked with the Remote Keyless Entry (RKE) transmitter.
268 UNDERSTANDING YOUR INSTRUMENT PANEL and select from “On” or “Off.” Press the back arrow/ arrow/Done button on the touchscreen to return to the Done button on the touchscreen to return to the previous previous menu. menu. • Flash Lights With Lock • Auto Dim High Beams — If Equipped When this feature is selected, the exterior lights will flash When this feature is selected, the high beam headlights will activate/deactivate automatically under certain conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL 269 NEUTRAL position and the driver’s door is opened. To make your selection, press the “Auto Unlock On Exit” button on the touchscreen and select from “On” or “Off.” Press the back arrow/Done button on the touchscreen to return to the previous menu.
270 UNDERSTANDING YOUR INSTRUMENT PANEL grabbed. To make your selection, press the “Passive Entry” button on the touchscreen and select from “On” or “Off.” Press the back arrow/Done button on the touchscreen to return to the previous menu. Refer to “Keyless Enter-N-Go™” in “Things To Know Before Starting Your Vehicle” for further information.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 10 minutes after the ignition is cycled to OFF. Opening either front door will cancel this feature. To change the After pressing the “Engine Off Options” button on the Engine Off Power Delay status press the “Engine Off touchscreen the following settings will be available. Power Delay” button and select from “0 seconds,” • Headlight Off Delay “45 seconds,” “5 minutes” or “10 minutes” buttons on the When this feature is selected, the driver can choose to touchscreen.
272 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Keep magnetic materials away from the top of the instrument panel, such as iPod’s, Mobile Phones, Laptops and Radar Detectors. This is where the compass module is located, and it can cause interference with the compass sensor, and it may give false readings. • Perform Compass Calibration Press the “Calibration” button on the touchscreen to change this setting. This compass is self-calibrating, which eliminates the need to manually reset the compass.
UNDERSTANDING YOUR INSTRUMENT PANEL 273 Press the back arrow/Done button on the touchscreen to • Surround Sound — If Equipped return to the previous menu. This feature provides simulated surround sound mode. • Equalizer To make your selection, press the “Surround Sound” When in this display you may adjust the Bass, Mid and button on the touchscreen, select “On” or “Off.” Press the Treble settings.
274 UNDERSTANDING YOUR INSTRUMENT PANEL the touchscreen, select “On” or “Off.” Press the back SiriusXM Setup — If Equipped arrow/Done button on the touchscreen to return to the After pressing the “SiriusXM Setup” button on the touchprevious menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 275 Press the “Subscription Info” button on the touchscreen If “Yes” is selected a pop-up will appear asking #Are you sure you want to reset your settings to default?” select to access the Subscription Information screen. “Yes” to restore, or “Cancel” to exit. Press back arrow/ Write down the SIRIUS ID numbers for your receiver. To Done button to return to the previous menu.
276 UNDERSTANDING YOUR INSTRUMENT PANEL Customer Programmable Features — Uconnect® 8.4 Settings mode, press and release the preferred setting until a check-mark appears next to the setting, showing that setting has been selected. Once the setting is complete, either press the Back Arrow button on the touchscreen to return to the previous menu, or press the “X” button on the touchscreen to close out of the settings screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 277 NOTE: When Day or Night is selected for the Display • Display Brightness With Headlights OFF Mode, the usage of the Parade Mode feature will cause When in this display, you may select the brightness with the radio to activate the Display Brightness Day control the headlights off. Adjust the brightness with the “+” and even though the headlights are on.
278 UNDERSTANDING YOUR INSTRUMENT PANEL • Set Language When in this display, you may select one of multiple languages (English / Français / Español) for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the Set Language button on the touchscreen, then press the desired language button on the touchscreen until a check-mark appears next to the language, showing that setting has been selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 279 Units • Pressure After pressing the “Units” button on the touchscreen you Select from: “psi,” “kPa,” or “bar.” may select each unit of measure independently displayed • Temperature in the Driver Information Display (DID), and navigation system (if equipped). The following selectable units of Select from: “°C,” or “°F.” measure are listed below: • Power • Speed Select from: “HP” (US), “HP” (UK), and “kW.” Select from: “MPH” or “km/h.
280 UNDERSTANDING YOUR INSTRUMENT PANEL Voice arrow button on the touchscreen to return to the previous menu. After pressing the “Voice” button on the touchscreen the following settings will be available: Clock • Voice Response Length After pressing the “Clock” button on the touchscreen the When in this display, you may change the Voice Re- following settings will be available: sponse Length settings.
UNDERSTANDING YOUR INSTRUMENT PANEL 281 buttons on the touchscreen to adjust the hours up or • Show Time In Status Bar — If Equipped down. Press the back arrow button on the touchscreen to This feature will allow you to turn on or shut off the return to the previous menu. digital clock in the status bar. To change the Show Time • Set Time Minutes Status setting press the “Show Time in Status Bar” button This feature will allow you to adjust the minutes.
282 UNDERSTANDING YOUR INSTRUMENT PANEL Near. The default status of FCW is the Far setting. This means the system will warn you of a possible collision with the vehicle in front of you when you are farther away. This gives you the most reaction time. To change the setting for more dynamic driving, select the Near setting. This warns you of a possible collision when you are much closer to the vehicle in front of you. To change the FCW status, press and release the “Near” or “Far” button.
UNDERSTANDING YOUR INSTRUMENT PANEL 283 effort. Press the “Comfort” button on the touchscreen to provide a balance of steering feel and steering effort. When this feature is selected, it sets the strength of the Press the back arrow button on the touchscreen to return steering wheel feedback for potential lane departures. to the previous menu.
284 UNDERSTANDING YOUR INSTRUMENT PANEL on the touchscreen, until a check-mark appears next to setting, indicating that the setting had been selected. The Front ParkSense® Chime Volume settings can be Press the back arrow button on the touchscreen to return selected from the DID or Uconnect® System. The chime to the previous menu. ParkSense® will retain its last volume settings include LOW, MEDIUM, and HIGH. The known configuration state through ignition cycles. factory default volume setting is MEDIUM.
UNDERSTANDING YOUR INSTRUMENT PANEL 285 Take your vehicle to an authorized dealer to verify sensor alignment. Having a sensor that is misaligned will result When this feature is selected, the Blind Spot Alert feature in the BSM not operating to specification. Provides alerts, visual and/or audible, to indicate objects in your blind spot. The Blind Spot Alert feature can be • ParkView® Backup Camera Active Guidelines activated in “Lights” mode.
286 UNDERSTANDING YOUR INSTRUMENT PANEL • ParkView® Backup Camera Delay When the vehicle is shifted out of REVERSE (with camera delay turned OFF), the rear camera mode is exited and the navigation or audio screen appears again.
UNDERSTANDING YOUR INSTRUMENT PANEL 287 transmitter. To change the Illuminated Approach status, After pressing the “Lights” button on the touchscreen the press the “+” or “-” button on the touchscreen to select your desired time interval. Press the back arrow button following settings will be available. on the touchscreen to return to the previous menu, or • Headlight Off Delay push the back button on the faceplate.
288 UNDERSTANDING YOUR INSTRUMENT PANEL indicating that the setting has been selected. Press the back arrow button on the touchscreen to return to the When this feature is selected, the high beam headlights previous menu, or push the back button on the faceplate. will activate/deactivate automatically under certain conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL 289 passive entry feature. This feature may be selected with After pressing the “Doors & Locks” button on the touch- or without the sound horn on lock feature selected. To make your selection, press the “Flash Lights with Lock” screen the following settings will be available: button on the touchscreen, until a check-mark appears • Auto Unlock On Exit next to setting, indicating that the setting has been When this feature is selected, all doors will unlock when selected.
290 UNDERSTANDING YOUR INSTRUMENT PANEL • Sound Horn With Remote Start When this feature is selected, the horn will sound when the remote start is activated. To make your selection, press the “Sound Horn with Remote Start” button on the touchscreen until a check-mark appears next to setting, showing that setting has been selected. Press the back arrow button on the touchscreen to return to the previous menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 291 setting, showing that the setting has been selected. Press the back arrow button on the touchscreen to return to the previous menu. Refer to “Keyless Enter-N-Go™” in “Things To Know Before Starting Your Vehicle”.
292 UNDERSTANDING YOUR INSTRUMENT PANEL Driver Heated/Ventilated Seat & Steering Wheel With Vehicle Start” button to select from “Off,” “Remote Start” or “All Starts” until a check-mark appears next to setting, showing that setting has been selected. Press the back arrow button on the touchscreen to return to the previous menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 293 Delay status press the “+” or “–” button on the touch- • Equalizer screen to select your desired time interval. Press the back This feature allows you to adjust the Bass, Mid and Treble arrow button on the touchscreen to return to the previous settings. Adjust the settings with the “+” and “–” setting menu.
294 UNDERSTANDING YOUR INSTRUMENT PANEL touchscreen, then choose “Yes” or “No.” Press the back arrow button on the touchscreen to return to the previous This feature provides simulated surround sound mode. menu. To make your selection, press the “Surround Sound” button on the touchscreen, select “On” or “Off.” Press the Phone/Bluetooth® back arrow button on the touchscreen to return to the After pressing the “Phone/Bluetooth®” button on the previous menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 295 Press the “Subscription Info” button on the touchscreen After pressing the “SiriusXM Setup” button on the touch- to access the Subscription Information screen. screen, the following settings will be available: Write down the SIRIUS ID numbers for your receiver. To reactivate your service, either call the number listed on • Channel Skip the screen or visit the provider online.
296 UNDERSTANDING YOUR INSTRUMENT PANEL select “Yes” to restore, or “Cancel” to exit. Once the System Information settings are restored, a pop up appears stating #settings After pressing the “System Information” button on the reset to default.# Press the okay button on the touchscreen touchscreen the following information will be available: to exit.
UNDERSTANDING YOUR INSTRUMENT PANEL 297 To access the Performance Pages, press the “Apps” button on the touchscreen then press the “Performance Pages” button on the touchscreen. Press the desired button on the touchscreen to access that specific Performance Page. WARNING! (Continued) exploited in a reckless or dangerous manner, which can jeopardize the user’s safety or the safety of others. Only a safe, attentive, and skillful driver can prevent accidents.
298 UNDERSTANDING YOUR INSTRUMENT PANEL The following describes each feature and its operation: Home When Home is selected, the following options will be available: • A series of six images which can be selected by the user. • A left and right arrow to allow the user to scroll through vehicle images. • A short-cut to the Performance Control feature.
UNDERSTANDING YOUR INSTRUMENT PANEL 299 When the Timers Page is selected you will be able to select from following “Tickets”: Timers • Current Pressing the “Current” button displays a “real time” summary of performance timers. • Last Pressing the “Last” button displays the last recorded run of performance timers. • Best Pressing the “Best” button displays the best recorded run of performance timers, except for braking data.
300 UNDERSTANDING YOUR INSTRUMENT PANEL • With a USB jump drive installed, press the “USB” button to save to the jump drive. • Save Pressing the “Save” button will let you save the last run. Any saved run over 10, will overwrite the last saved run • With an SD Card installed, press the “SD Card” to save for Uconnect® System storage. The operation of the Save runs to the SD Card. feature is listed below: • Press the “Uconnect” button to save the runs to the Owner web page.
UNDERSTANDING YOUR INSTRUMENT PANEL 301 NOTE: The Reaction Time, MPH, ⅛ and ¼ Mile timers • Brake Distance will be “ready” when the vehicle is at 0 MPH (0 km/h) Displays the distance it takes the vehicle to make a full • 0-60 MPH (0-100 km/h) stop. Displays the time it takes for the vehicle to go from 0 to NOTE: The distance measurement will be aborted if the 60 mph (0 to 100 km/h). brake pedal is released or the parking brake is engaged, before the vehicle comes to a complete stop.
302 UNDERSTANDING YOUR INSTRUMENT PANEL When selected, this screen displays the following values: Gauges 1 • Coolant Temperature Shows the actual coolant temperature. • Oil Pressure Shows the actual oil pressure. • Oil Temperature Shows the actual oil temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL 303 Gauges 2 4 Performance Pages — Gauges 2 (Manual Transmission) Performance Pages — Gauges 2 (Automatic Transmission)
304 UNDERSTANDING YOUR INSTRUMENT PANEL When selected, this screen displays the following values: G-Force • Battery Voltage Shows the actual battery voltage. • Intake Air Temperature Shows the actual intake air temperature. • Transmission Temperature (Automatic Transmission Only) Shows the actual transmission temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL 305 When selected, this screen displays all four G-Force • Peak G-Forces Fore Aft, Left and Right values (two lateral and two longitudinal) as well as This shows the maximum g-forces that have been steering angle. achieved since the last reset from the DID. Peak values When G-Force is selected, the following features will be are maintained through ignition cycles by the DID until available: they are cleared by the driver.
306 UNDERSTANDING YOUR INSTRUMENT PANEL When selected, this screen displays the following values: Engine • Vehicle Speed Shows the actual vehicle speed. • Instantaneous Horsepower/Kilowatts Shows the instantaneous horsepower. • Instantaneous Torque Shows the instantaneous torque. • Oil Pressure Shows the actual engine oil pressure. Performance Pages — Engine • Gear (Automatic Transmission Only) Shows the current (or pending) operating gear of the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 307 Descriptions of these features are provided below. To Your vehicle is equipped with a Performance Control access information about the functionality of these feafeature which allows for coordinating the operation of tures through the Uconnect® system, press the “Info” button on the touchscreen. various vehicle systems depending upon the type of driving behavior desired.
308 UNDERSTANDING YOUR INSTRUMENT PANEL quarter mile and zero to sixty times are desired. The system is not intended to compensate for lack of driver experience or familiarity with the race track. Use of this feature in low traction (cold, wet, gravel, etc.) conditions may results in excess wheel slip outside this systems control resulting in an aborted launch. NOTE: • Launch control should not be used on public roads. Always check track conditions and the surrounding area.
UNDERSTANDING YOUR INSTRUMENT PANEL 309 Automatic Transmission — If Equipped Launch Control is only available when the following procedure is followed: 1. Press the “Apps” button on the touchscreen, select “Performance Control”, and press the “Launch Control” button on the touchscreen or push the Super Track Pak button on the integrated center stack switch bank. NOTE: The default RPM for launch control is a preset factory value.
310 UNDERSTANDING YOUR INSTRUMENT PANEL 6. While holding the brake, rapidly apply the accelerator Launch Control will abort before launch completion and pedal to wide open throttle. The engine speed will display “Launch Aborted” in the DID for any the followhold at the RPM that was set in the “Launch RPM ing conditions: Set-up” screen. • The accelerator pedal is released during launch.
UNDERSTANDING YOUR INSTRUMENT PANEL 311 Manual Transmission — If Equipped Launch Control is only available when the following procedure is followed: 1. Press the “Apps” button on the touchscreen, select Performance Control, and press the “Launch Control” button on the touchscreen or push the Super Track Pak button on the center stack switch bank. NOTE: The default for launch control is 3000 RPM. Optimal launch RPM will depend on the engine and tires on the vehicle, as well as road and weather conditions.
312 UNDERSTANDING YOUR INSTRUMENT PANEL 6. While holding the clutch depressed, rapidly apply the Launch Control will abort before launch completion and accelerator pedal to wide open throttle. The engine display “Launch Aborted” in the DID for any the followspeed will hold at the RPM that was set in the “Launch ing conditions: RPM Set-up” screen. • The brake is applied during launch.
UNDERSTANDING YOUR INSTRUMENT PANEL 313 Drive Mode Set-Up Pressing the “Drive Mode Set-Up” button on the touchscreen within the Performance Control screen indicates the real-time status of the various systems. Pressing the “Sport Mode Set-Up” or “Default Mode Set-Up” buttons on the touchscreen, the driver can configure their individual drive modes and see how those configurations affect the performance of the vehicle.
314 UNDERSTANDING YOUR INSTRUMENT PANEL Available Mode Configurations Transmission Auto Manual Engine N/A X Engine/Trans X N/A Steering X X Paddle Shifters X N/A Refer to the Sport and Default modes for their detailed Default Mode operation. NOTE: These settings will remain in effect when using the Launch Control feature.
UNDERSTANDING YOUR INSTRUMENT PANEL 315 The vehicle will always start in Default Mode. This mode is for typical driving conditions. While in Default Mode, the Engine, Transmission and Traction will operate in their Normal settings and cannot be changed. The Steering assist may be configured to Normal, Sport, or Comfort by pressing the corresponding buttons on the touchscreen. The Paddle Shifters may be enabled or disabled while in this mode.
316 UNDERSTANDING YOUR INSTRUMENT PANEL Sport Mode is a configuration set-up for typical enthusiast driving. The Transmission and Steering are both set to their Sport settings. The steering wheel paddle switches are enabled. The Traction Control defaults to Normal. Any of these four settings may be changed to the driver’s preferences by pressing the buttons on the touchscreen. Push the Sport button on the instrument panel switch bank to put the vehicle in Sport Mode and activate these settings.
UNDERSTANDING YOUR INSTRUMENT PANEL 317 Possible Drive Mode configurations are listed below with accompanying descriptions. The information contained in the list below can also be accessed from within the mode Set-Up menus. To access the information, press the “Info” button on the touchscreen from the mode Set-Up menu, and use the left/right arrows to toggle through available descriptions.
318 UNDERSTANDING YOUR INSTRUMENT PANEL Engine • Sport Press the “Sport” button on the touchscreen for improved throttle response for an enhanced driving experience. • Normal Press the “Norm” button on the touchscreen for standard throttle response for normal driving.
UNDERSTANDING YOUR INSTRUMENT PANEL 319 Engine/Trans • Sport Press the “Sport” button on the touchscreen for improved throttle response and modified shifting for an enhanced driving experience. • Normal Press the “Norm” button on the touchscreen for a balance of throttle response, shift comfort and economy for normal driving.
320 UNDERSTANDING YOUR INSTRUMENT PANEL Paddle Shifters • ON Press the “ON” button on the touchscreen to enable steering wheel Paddle Shifters. • OFF Press the “OFF” button on the touchscreen to disable steering wheel Paddle Shifters.
UNDERSTANDING YOUR INSTRUMENT PANEL 321 Steering 4 Traction Control • SPORT Press the “SPORT” button on the touchscreen to turn off traction control and reduce stability control. • Sport • NORMAL Steering Press the “Sport” button on the touchscreen to provide Press the “NORM” button on the touchscreen to provide the greatest amount of steering feel, requiring the highest amount of steering effort. full traction control and full stability control.
322 UNDERSTANDING YOUR INSTRUMENT PANEL Located in the front storage area of the center console, this feature allows an iPod®/MP3 player, or an external Press the “Norm” button on the touchscreen to provide USB device, to be connected to the audio system. greater steering feel, requiring greater steering effort. • Normal • Comfort Press the “Comf” button on the touchscreen to provide a balance of steering feel and steering effort.
UNDERSTANDING YOUR INSTRUMENT PANEL 323 iPod® control supports Mini, 4G, Photo, Nano, 5G iPod® and iPhone® devices. Some iPod® software versions may not fully support the iPod® control features. Please visit Apple’s website for software updates. For further information, refer to the Uconnect® User’s Manual. 4 STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches.
324 UNDERSTANDING YOUR INSTRUMENT PANEL Pushing the center button will make the radio switch Media Mode between the various modes available (AM/FM/AUX etc.). Pushing the top of the switch once will go to the next The left-hand control is a rocker-type switch with a track on the selected media (AUX, Bluetooth®, SD Card). push-button in the center. The function of the left-hand Pushing the bottom of the switch once will go to the control is different depending on which mode you are in.
UNDERSTANDING YOUR INSTRUMENT PANEL 325 antenna, it is recommended that the radio volume be emitted is far less than the electromagnetic energy emitturned down or off during mobile phone operation when ted by wireless devices such as mobile phones. However, the use of wireless radios may be restricted in some not using Uconnect® (if equipped). situations or environments, such as aboard airplanes.
326 UNDERSTANDING YOUR INSTRUMENT PANEL brouillage radioélectrique subi, même si le brouillage est • Increase the separation between the equipment and susceptible d’en compromettre le fonctionnement. receiver. NOTE: • This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
UNDERSTANDING YOUR INSTRUMENT PANEL 327 General Overview Buttons On The Touchscreen Buttons On The Faceplate Buttons on the touchscreen are accessible on the Uconnect® system screen. The buttons on the faceplate are located below the Uconnect® screen. 4 Automatic Climate Controls — Buttons On The Faceplate Uconnect® 5.
328 UNDERSTANDING YOUR INSTRUMENT PANEL this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off. 2. A/C Button Press and release to change the current setting, the indicator illuminates when A/C is ON. Performing this function again will cause the A/C operation to switch into manual mode and the A/C indicator will turn off. 3. Recirculation Button Uconnect® 8.
UNDERSTANDING YOUR INSTRUMENT PANEL 329 5. Front Defrost Button Press and release to change the current airflow setting to Defrost mode. The indicator illuminates when this feature is ON. Air comes from the windshield and side window demist outlets. When the defrost button is selected, the blower level will increase. Use Defrost mode with maximum temperature settings for best windshield and side window defrosting and defogging. Performing this function will cause the ATC to switch into manual mode.
330 UNDERSTANDING YOUR INSTRUMENT PANEL temperature settings or on the touchscreen, press and when this feature is enabled. Sync is used to synchronize slide the temperature bar button towards the red arrow the passenger temperature setting with the driver temfor warmer temperature settings. perature setting. Changing the passenger temperature setting while in Sync will automatically exit this feature. NOTE: Pressing this button while in Sync mode will 10. Blower Control automatically exit Sync.
UNDERSTANDING YOUR INSTRUMENT PANEL 331 Button On The Touchscreen • Bi-Level Mode Air comes from the instrument panel outlets and Use the small blower icon to reduce the blower setting floor outlets. A slight amount of air is directed and the large blower icon to increase the blower setting. through the defrost and side window demister outlets. Blower can also be selected by pressing the blower bar area between the icons. NOTE: BI-LEVEL mode is designed under comfort con11.
332 UNDERSTANDING YOUR INSTRUMENT PANEL 12. Climate Control OFF Button 14. Driver Temperature Control Up Button (Uconnect® 8.4 Only) Press and release this button to turn the Climate Control ON/OFF. Provides the driver with independent temperature con13. Driver Temperature Control Down Button trol. Push the button on the faceplate for warmer temperature settings or on the touchscreen, press and slide (Uconnect® 8.
UNDERSTANDING YOUR INSTRUMENT PANEL 333 Climate Control Functions A/C (Air Conditioning) • If fog or mist appears on the windshield or side glass, select Defrost mode and adjust blower speed if needed. The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning • If your air conditioning performance seems lower than expected, check the front of the A/C condenser (losystem.
334 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: In cold weather, use of Recirculation mode may lead to excessive window fogging. The recirculation feature may be unavailable (button on touchscreen greyed out). The Recirculation mode is not allowed in Defrost mode to improve window clearing operation. Recirculation Recirculation will be disabled automatically if this mode is selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 335 2. Next, adjust the temperature you would like the • The temperature can be displayed in U.S. or Metric system to maintain by adjusting the driver and pasunits by selecting the Uconnect® customersenger temperature buttons on the faceplate or butprogrammable feature. Refer to the “Uconnect® Systons on the touchscreen. Once the desired temperature tem Settings” in this section of the manual.
336 UNDERSTANDING YOUR INSTRUMENT PANEL The operator can also select the direction of the airflow by selecting one of the available mode settings. A/C operation and Recirculation control can also be manually selected in Manual operation. coolant that meets the requirements of Chrysler Material Standard MS.90032 and 50% water is recommended. Refer to “Maintenance Procedures” in “Maintaining Your Vehicle” for proper coolant selection. NOTE: Each of these features operates independently from each other.
UNDERSTANDING YOUR INSTRUMENT PANEL 337 Window Fogging Outside Air Intake Interior fogging on the windshield can be quickly removed by turning the mode selector to Defrost. The Defrost/Floor mode can be used to maintain a clear windshield and provide sufficient heating. If side window fogging becomes objectionable, increase blower speed to improve airflow and clearing of the side windows. Vehicle windows tend to fog on the inside in mild but rainy or humid weather.
338 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions For Various Weather Conditions
UNDERSTANDING YOUR INSTRUMENT PANEL 339 Uconnect® VOICE RECOGNITION QUICK TIPS Introducing Uconnect® Start using Uconnect® Voice Recognition with these helpful quick tips. It provides the key Voice Commands and tips you need to know to control your Uconnect® 5.0 or 8.4A/8.4AN system. 4 Uconnect® 8.4AN If you see the icon on your touchscreen, you have the Uconnect® 8.4AN system. If not, you have a Uconnect® 8.4A system.
340 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Each time you give a Voice Command, you must first push either the VR or Phone button, wait until after All you need to control your Uconnect® system with the beep, then say your Voice Command. your voice are the buttons on your steering wheel. 1. Visit UconnectPhone.com to check mobile device and 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 341 Basic Voice Commands The basic Voice Commands below can be given at any point while using your Uconnect® system. Push the VR button . After the beep, say: • Cancel to stop a current voice session • Help to hear a list of suggested Voice Commands • Repeat to listen to the system prompts again Uconnect® Voice Command 1 — Push To Initiate Or To Answer A Phone Call, Send Or Receive A Text 2 — For all radios: Push To Begin Radio or Media functions. For 8.4A/8.
342 UNDERSTANDING YOUR INSTRUMENT PANEL Notice the visual cues that inform you of your voice Radio recognition system’s status. Cues appear on the touchscreen. Use your voice to quickly get to the AM, FM or SiriusXM Satellite Radio stations you would like to hear. (Subscription or included SiriusXM Satellite Radio trial required.) Push the VR button .
UNDERSTANDING YOUR INSTRUMENT PANEL 343 . After the beep, say one of the Push the VR button following commands and follow the prompts to switch your media source or choose an artist. • Change source to Bluetooth® • Change source to iPod® • Change source to USB • Play artist Beethoven; Play album Greatest Hits; Play song Moonlight Sonata; Play genre Classical Uconnect® 8.4A/8.4AN Radio Media Uconnect® offers connections via USB, SD, Bluetooth® and auxiliary ports (If Equipped).
344 UNDERSTANDING YOUR INSTRUMENT PANEL . After the beep, say one of Push the Phone button the following commands: • Call John Smith • Dial 123-456-7890 and follow the system prompts • Redial (call previous outgoing phone number) • Call back (call previous incoming phone number) Uconnect® 8.4A/8.4AN Media Phone Making and answering hands-free phone calls is easy with Uconnect®. When the Phonebook button is illuminated on your touchscreen, your system is ready. Check UconnectPhone.
UNDERSTANDING YOUR INSTRUMENT PANEL 345 1. Once an incoming text message is read to you, push . After the beep, say: “Reply.” the Phone button 2. Listen to the Uconnect® prompts. After the beep, repeat one of the pre-defined messages and follow the system prompts. Uconnect® 8.4A/8.4AN Phone Voice Text Reply Uconnect® will announce incoming text messages. Push and say Listen. (Must have comthe Phone button patible mobile phone paired to Uconnect® system.) PRE-DEFINED VOICE TEXT REPLY RESPONSES Yes.
346 UNDERSTANDING YOUR INSTRUMENT PANEL TIP: Your mobile phone must have the full implementation of the Message Access Profile (MAP) to take advantage of this feature. For details about MAP, visit UconnectPhone.com. Apple iPhone® iOS6 or later supports reading incoming text messages only. TIP: Voice Command for Climate may only be used to adjust the interior temperature of your vehicle. Voice Command will not work to adjust the heated seats or steering wheel (If equipped). Climate (8.4A/8.
UNDERSTANDING YOUR INSTRUMENT PANEL 347 Navigation (8.4A/8.4AN) The Uconnect® navigation feature helps you save time and become more productive when you know exactly how to get to where you want to go. (Navigation is optional on the Uconnect® 8.4A system. See your dealer to activate navigation at any time.) 1. To enter a destination, press the VR button the beep, say: 4 . After • For the 8.4A Uconnect® System, say: “Enter state.” • For the 8.
348 UNDERSTANDING YOUR INSTRUMENT PANEL press the Apps button on the 8.4-inch touchscreen to get started. Detailed registration instructions can be found on the next page. Roadside Assistance Call Wi-Fi Hotspot*** **If vehicle is equipped. *Uconnect® Access is available only on equipped vehicles purchased within the continental United States and ***Extra charges apply. Alaska. Services can only be used where coverage is Register (8.4A/8.4AN) available; see coverage map for details. 1.
UNDERSTANDING YOUR INSTRUMENT PANEL 349 5. Click on the link inside the email within 72 hours and complete the easy online registration process to create a personal Mopar® Owner Connect account linked to your vehicle. Mobile App (8.4A/8.4AN) Securely link your mobile device to your vehicle with the Uconnect® Access App. Once you have downloaded the App, you may start your vehicle or lock it from virtually any distance. (Vehicle must be properly equipped with factory-installed Remote Start.
350 UNDERSTANDING YOUR INSTRUMENT PANEL Download the Uconnect® Access App to a compatible 2. Listen to the prompt. After the beep, dictate the Apple® or Android® mobile devices. All you need to do message you would like to send. Wait for Uconnect® is: to process your message. 1. After registering with Uconnect® Access, log on to 3. The Uconnect® system will repeat your message and your Mopar® Owner Connect account at mopprovide a variety of options to add to, delete, send or arownerconnect.com.
UNDERSTANDING YOUR INSTRUMENT PANEL 351 Yelp® (8.4A/8.4AN) Once registered with Uconnect® Access, you can use your voice to search for the most popular places or things around you. 1. Press the VR button “Launch YELP.” . After the beep, say: 4 2. Once the YELP® home screen appears on the touchscreen, press the VR button , then say: “YELP search.” 3. Listen to the system prompts and after the beep, tell Uconnect® the place or business that you’d like Uconnect® to find.
352 UNDERSTANDING YOUR INSTRUMENT PANEL SiriusXM Travel Link™ (8.4A/8.4AN) Need to find a gas station, view local movie listings, check a sports score or the 5 - day weather forecast? SiriusXM Travel Link™ is a suite of services that brings a wealth of information right to your Uconnect® 8.4AN system. (Not available for 8.4A system.) Press the VR button following commands: .
UNDERSTANDING YOUR INSTRUMENT PANEL 353 Additional Information Uconnect® System Support: © 2014 Chrysler Group LLC. All rights reserved. Mopar and Uconnect are registered trademarks and Mopar Owner Connect is a trademark of Chrysler Group LLC. Android is a trademark of Google Inc. SiriusXM and all related marks and logos are trademarks of SiriusXM Radio Inc. Yelp, Yelp logo, Yelp burst and related marks are registered trademarks of Yelp. • U.S. residents call 1-877-855-8400 or visit DriveUconnect.
STARTING AND OPERATING CONTENTS ! STARTING PROCEDURES . . . . . . . . . . . . . . . .360 ! MANUAL TRANSMISSION — IF EQUIPPED . .368 ▫ Manual Transmission — If Equipped . . . . . . . .360 ▫ Six-Speed Manual Transmission . . . . . . . . . . .368 ▫ Automatic Transmission — If Equipped . . . . .361 ▫ Shifting. . . . . . . . . . . . . . . . . . . . . . . . . . . . .369 ▫ Keyless Enter-N-Go™ . . . . . . . . . . . . . . . . . .362 ▫ Recommended Shift Speeds . . . . . . . . . . . . . .370 ▫ Normal Starting. .
356 STARTING AND OPERATING ▫ Eight-Speed Automatic Transmission — If ! FUEL SAVER TECHNOLOGY 5.7L/6.4L ENGINES Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .375 ONLY — IF EQUIPPED . . . . . . . . . . . . . . . . . .389 ! AUTOSTICK . . . . . . . . . . . . . . . . . . . . . . . . . .382 ! PARKING BRAKE . . . . . . . . . . . . . . . . . . . . . .390 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .382 ▫ Manual Transmission — If Equipped . . . . . . . .
STARTING AND OPERATING 357 ▫ Synchronizing ESC . . . . . . . . . . . . . . . . . . . .403 ▫ Spare Tires — If Equipped . . . . . . . . . . . . . . .421 ! TIRE SAFETY INFORMATION . . . . . . . . . . . . .404 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . .424 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . .404 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . .424 ▫ Tire Identification Number (TIN). . . . . . . . . . .407 ▫ Life Of Tire . . . . . . . . . . . . . .
358 STARTING AND OPERATING ▫ 5.7L Engine (With Manual Transmission) . . . . .438 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . .445 ▫ 6.4L Engine . . . . . . . . . . . . . . . . . . . . . . . . . .438 ! VEHICLE LOADING . . . . . . . . . . . . . . . . . . . .445 ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . .439 ▫ Vehicle Certification Label . . . . . . . . . . . . . . .445 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . .439 ▫ Gross Vehicle Weight Rating (GVWR) . . . . . . .
STARTING AND OPERATING 359 ▫ Trailer Towing Weights (Maximum Trailer Weight Ratings) . . . . . . . . . . . . . . . . . . . . . . . . . . . .452 ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . .459 ▫ Trailer And Tongue Weight . . . . . . . . . . . . . .453 ! RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) . . . . . . . . . . . . . . . . . . .460 ▫ Towing Requirements . . . . . . . . . . . . . . . . . .454 ▫ Towing This Vehicle Behind Another Vehicle . .
360 STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! • When leaving the vehicle, always make sure the ignition is in the OFF position, remove the Key Fob from the vehicle, and lock the vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle.
STARTING AND OPERATING 361 Press the clutch pedal fully to the floor, and cycle the ignition switch to the START position and release when the engine starts. If the engine fails to start within 15 seconds, place the ignition in the OFF position, wait 10 to 15 seconds, then repeat the “Normal Starting” procedure. WARNING! Do not attempt to push or tow your vehicle to get it started.
362 STARTING AND OPERATING Using Fob With Integrated Key (Tip Start) NOTE: Normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal. Keyless Enter-N-Go™ This feature allows the driver to operate the ignition switch with the push of a button, as long as the ENGINE START/STOP button is installed and the Remote Start/Keyless Enter-NGo™ Key Fob is in the passenger compartment. Do not press the accelerator.
STARTING AND OPERATING 363 3. The system takes over and attempts to start the 3. If you wish to stop the cranking of the engine prior to the engine starting, release the button. vehicle. If the vehicle fails to start, the starter will disengage automatically after 10 seconds. NOTE: Normal starting of either a cold or a warm 4. If you wish to stop the cranking of the engine prior to engine is obtained without pumping or pressing the accelerator pedal. the engine starting, press the button again.
364 STARTING AND OPERATING position. If the shift lever is not in PARK and the 2. The ignition switch will return to the OFF position. ENGINE START/STOP button is pressed once, the 3. Place the shift lever in first gear or REVERSE and then Driver Information Display (DID) will display a “VEapply the parking brake. HICLE NOT IN PARK” message and the engine will remain running. Never leave a vehicle out of the NOTE: PARK position, or it could roll.
STARTING AND OPERATING 365 switch position will remain in the ACC position until 3. Press the ENGINE START/STOP button a third time to return the ignition switch to the OFF position. the vehicle is stopped and the button is pressed twice to the OFF position.
366 STARTING AND OPERATING WARNING! (Continued) • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. • If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.
STARTING AND OPERATING 367 Clearing A Flooded Engine (Using ENGINE START/STOP Button) — Manual Transmission Only ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a If the engine fails to start after you have followed the standard 110-115 Volt AC electrical outlet with a “Normal Starting” or “Extreme Cold Weather# proce- grounded, three-wire extension cord. dures, it may be flooded.
368 STARTING AND OPERATING MANUAL TRANSMISSION — IF EQUIPPED Six-Speed Manual Transmission WARNING! You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied. The parking brake should always be applied when the driver is not in the vehicle, especially on an incline.
STARTING AND OPERATING 369 NOTE: During cold weather, you may experience in- Shifting creased effort in shifting until the transmission fluid Fully press the clutch pedal and lift your foot off the warms up. This is normal. accelerator pedal before shifting gears. As you release the clutch pedal, lightly press the accelerator pedal. Damage to the transmission or clutch may occur if you do not fully press the clutch pedal and lift off of the accelerator pedal when shifting.
370 STARTING AND OPERATING CAUTION! You must always use first gear (or REVERSE) when starting from a standing position. Always make sure the vehicle comes to a complete stop before shifting into REVERSE. Failure to do so may result in transmission damage. Recommended Shift Speeds To utilize your manual transmission efficiently for fuel economy, it should be upshifted as listed in recommended shift speed chart. Axle Ratio 3.
STARTING AND OPERATING 371 NOTE: • Your vehicle is equipped with a transmission reverse inhibitor system. When vehicle speed is greater than 3 mph (5 km/h), the reverse inhibitor activates to help prevent shifts into REVERSE. When at a complete stop, you may notice lighter shift efforts into REVERSE with the ignition switch in the ON position (RUN position for Keyless Enter-N-Go™), as compared to the ignition LOCK position (OFF position for Keyless Enter-NGo™).
372 STARTING AND OPERATING Downshifting AUTOMATIC TRANSMISSION To maintain a safe speed and prolong brake life, downshift to maintain a safe speed when descending a steep grade. WARNING! Skipping more than one gear while downshifting, could cause you to lose control of your vehicle. You could have a collision. CAUTION! • If you skip more than one gear while downshifting or downshift at too high an engine speed, you could damage the engine, transmission, or clutch.
STARTING AND OPERATING 373 WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, turn the engine OFF, and remove the Key Fob. When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.
374 STARTING AND OPERATING CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Shift into or out of PARK or REVERSE only after the vehicle has come to a complete stop. • Do not shift between PARK, REVERSE, NEUTRAL, or DRIVE when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly pressing the brake pedal.
STARTING AND OPERATING 375 Eight-Speed Automatic Transmission — If Equipped The transmission gear range (PRNDM) is displayed both on the shift lever and in the Driver Information Display (DID). To select a gear range, press the lock button on the shift lever and move the lever rearward or forward.
376 STARTING AND OPERATING Only shift from DRIVE to PARK or REVERSE when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when shifting between these gears. The transmission shift lever has PARK, REVERSE, NEUTRAL, DRIVE, and MANUAL (Autostick) shift positions. Manual shifts can be made using the Autostick shift control (refer to “AutoStick” in this section for further information).
STARTING AND OPERATING 377 Never attempt to use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. When parking on a level surface, you may shift the transmission into PARK first, and then apply the parking brake. When parking on a hill, apply the parking brake before shifting the transmission to PARK. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.
378 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, turn the engine OFF, and remove the key fob. When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.
STARTING AND OPERATING 379 CAUTION! • Before moving the shift lever out of PARK, you must start the engine and also press the brake pedal. Otherwise, damage to the shift lever could result. • DO NOT race the engine when shifting from PARK or NEUTRAL into another gear range, as this can damage the drivetrain. • With brake pedal released, verify that the shift lever will not move out of PARK. REVERSE (R) This range is for moving the vehicle backward.
380 STARTING AND OPERATING WARNING! (Continued) practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. CAUTION! Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage. Refer to “Recreational Towing” in “Starting And Operating” and “Towing A Disabled Vehicle” in “What To Do In Emergencies” for further information.
STARTING AND OPERATING 381 restarted. The Malfunction Indicator Light (MIL) may be The MANUAL (M, +/-) position (beside the DRIVE illuminated. A message in the instrument cluster will position) enables full manual control of transmission inform the driver of the more serious conditions, and indicate what actions may be necessary. shifting (also known as AutoStick mode; refer to “AutoStick” in this section for further information).
382 STARTING AND OPERATING braking, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system 5. Restart the engine. can also provide you with more control during passing, 6. Shift into the desired gear range. If the problem is no city driving, cold slippery conditions, mountain driving, longer detected, the transmission will return to normal trailer towing, and many other situations. operation.
STARTING AND OPERATING 383 NOTE: Tapping one of the steering wheel-mounted shift • In temporary AutoStick mode (shift lever in DRIVE), paddles (+/-), if equipped, while the shift lever is in the transmission will automatically shift up when DRIVE, will activate a temporary AutoStick mode. Tapmaximum engine speed is reached.
384 STARTING AND OPERATING • The transmission will automatically downshift to first • Transmission shifting will be more noticeable when gear when coming to a stop. After a stop, the driver AutoStick is engaged. should manually upshift (+) the transmission as the • The system may revert to automatic shift mode if a vehicle is accelerated. fault or overheat condition is detected. • You can start out, from a stop, in first or second gear.
STARTING AND OPERATING 385 SPORT MODE — WITHOUT PERFORMANCE CONTROL Your vehicle is equipped with a Sport Mode feature. This mode is a configuration set up for typical enthusiast driving. The engine, transmission (when equipped with automatic transmission), and steering systems are all set to their SPORT settings. Sport Mode will provide improved throttle response and modified shifting for an enhanced driving experience, as well the greatest amount of steering feel.
386 STARTING AND OPERATING Your vehicle may be equipped with a Limited Slip When driving on wet or slushy roads, it is possible for a Differential (LSD) that reduces, but does not eliminate, wedge of water to build up between the tire and road the amount of wheel slip across a given axle for improved handling. surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping DRIVING THROUGH WATER ability.
STARTING AND OPERATING 387 WARNING! (Continued) WARNING! (Continued) carry your vehicle away swiftly. Failure to follow this warning may result in injuries that are serious or fatal to you, your passengers, and others around you. Although your vehicle is capable of driving through shallow standing water, consider the following Cautions and Warnings before doing so. • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances.
388 STARTING AND OPERATING CAUTION! (Continued) CAUTION! (Continued) • Determine the condition of the road or the path that is under water and if there are any obstacles in the way before driving through the standing water. • Do not exceed 5 mph (8 km/h) when driving through standing water. This will minimize wave effects. • Driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.e., engine oil, transmission, axle, etc.
STARTING AND OPERATING 389 Equipped” within “Uconnect Settings” in “Understanding NOTE: Your Instrument Panel” chapter for further information. • Even if the power steering assistance is no longer operational, it is still possible to steer the vehicle. WARNING! Under these conditions there will be a substantial increase in steering effort, especially at low speeds and Continued operation with reduced assist could pose during parking maneuvers. a safety risk to yourself and others.
390 STARTING AND OPERATING • This light only shows that the parking brake is applied. It does not show the degree of brake application. Before leaving the vehicle, make sure that the parking brake is fully applied and place the shift lever in the When parking on a hill, it is important to turn the front PARK or REVERSE (manual transmission only) position. wheels toward the curb on a downhill grade and away When the parking brake is applied and the ignition from the curb on an uphill grade.
STARTING AND OPERATING 391 Manual Transmission — If Equipped Automatic Transmission — If Equipped The foot operated parking brake is positioned below the The foot operated parking brake is located below the lower lower left corner of the instrument panel. To release the left corner of the instrument panel. To apply the park brake, firmly push the park brake pedal fully. To release the parking brake, pull the parking brake release handle.
392 STARTING AND OPERATING WARNING! WARNING! (Continued) • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • When leaving the vehicle, always remove the Key Fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons.
STARTING AND OPERATING 393 CAUTION! If the “Brake Warning Light” remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. BRAKE SYSTEM In the event power assist is lost for any reason (for example, repeated brake applications with the engine OFF) the brakes will still function. The effort required to brake the vehicle will be much greater than that required with the power system operating.
394 STARTING AND OPERATING System), and the ESC (Electronic Stability Control). These related motor noises. These noises are the system persystems work together to enhance both vehicle stability forming its self check cycle to ensure that the ABS system is working properly. This self check occurs each time the and control in various driving conditions. vehicle is started and accelerated past 7 mph (11 km/h).
STARTING AND OPERATING 395 These are all normal characteristics of ABS. WARNING! (Continued) WARNING! • The Anti-Lock Brake System (ABS) contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals.
396 STARTING AND OPERATING Anti-Lock Brake Warning Light The “Anti-Lock Brake System (ABS) Warning Light” monitors the Anti-Lock Brake System. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the “ABS Warning Light” remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.
STARTING AND OPERATING 397 even if TCS and ESC are in the “Partial Off” or #Full Off# mode. Refer to “Electronic Stability Control (ESC)” in this section for more information. Brake Assist System (BAS) This system complements the ABS by optimizing the vehicle braking capability during emergency braking maneuvers. This system detects an emergency braking situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce braking distances.
398 STARTING AND OPERATING during this short period of time, the system will release brake pressure and the vehicle will roll down the hill. The system will release brake pressure in proportion to amount of throttle applied as the vehicle starts to move in the intended direction of travel. HSA Activation Criteria The following criteria must be met in order for HSA to activate: • Vehicle must be stopped.
STARTING AND OPERATING 399 by applying the brake of the appropriate wheel. Engine power may also be reduced to assist in counteracting the condition of oversteer or understeer and help the vehicle maintain the desired path. The ESC uses sensors in the vehicle to determine the path that the driver intends to steer the vehicle and compares it to the actual path of the vehicle.
400 STARTING AND OPERATING center of the instrument panel or in the touchscreen radio The ESC system has two or three available operating . To enter the “Partial Off” mode, momentarily press the “ESC Off” switch and the “ESC Off Indicator Light” will modes: illuminate. To turn the ESC ON again, momentarily press ESC On the “ESC Off” switch and the “ESC Off Indicator Light” This is the normal operating mode for the ESC. When- will turn off.
STARTING AND OPERATING 401 WARNING! When in “Partial Off” mode, the TCS portion of ESC, except for the limited wheel spin feature described in the TCS section, has been disabled and the “ESC Off Indicator Light” will be illuminated. When in “Partial Off” mode, the enhanced vehicle stability offered by the ESC system is reduced. Full Off — If Equipped This mode is intended for off-highway or off-road use only and should not be used on any public roadways.
402 STARTING AND OPERATING NOTE: When the ESC is switched OFF, a feature of the system remains active. This feature controls wheel spin across an axle quite similarly to a limited slip differential. If one wheel on an axle is spinning faster than the other, the system will apply the brake of the spinning wheel and allow more engine torque to be applied to the wheel that is not spinning.
STARTING AND OPERATING 403 NOTE: Synchronizing ESC • The “ESC Off Indicator Light” and the “ESC Activation/Malfunction Indicator Light” come on momentarily each time the ignition switch is turned to the ON/RUN position. • Each time the ignition is cycled to the ON/RUN position, the ESC system will be ON even if it was cycled off previously. • The ESC system will make buzzing or clicking sounds when it is active.
404 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger) — Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European — Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter #P# is absent from this tire size designation.
STARTING AND OPERATING 405 • Temporary spare tires are designed for temporary • High flotation tire sizing is based on U.S. design emergency use only. Temporary high pressure comstandards and it begins with the tire diameter molded pact spare tires have the letter “T” or “S” molded into into the sidewall. Example: 31x10.5 R15 LT. the sidewall preceding the size designation. Example: T145/80D18 103M.
406 STARTING AND OPERATING EXAMPLE: R = Construction code – #R# means radial construction, or – #D# means diagonal or bias construction 15, 16, 18 = Rim diameter in inches (in) Service Description: 95 = Load Index – A numerical code associated with the maximum load a tire can carry H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions – The maximum speed corresponding to the speed symbol should only be
STARTING AND OPERATING 407 EXAMPLE: Load Identification: Absence of the following load identification symbols on the sidewall of the tire indicates a Standard Load (SL) tire: • XL = Extra load (or reinforced) tire, or • LL = Light load tire or • C, D, E, F, G = Load range associated with the maximum load a tire can carry at a specified pressure Maximum Load – Maximum load indicates the maximum load this tire is designed to carry Maximum Pressure – Maximum pressure indicates the maximum permissible cold tir
408 STARTING AND OPERATING EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation – This symbol certifies that the tire is in compliance with the U.S.
STARTING AND OPERATING 409 Tire Terminology And Definitions Term B-Pillar Cold Tire Inflation Pressure Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
410 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
STARTING AND OPERATING 411 Tire And Loading Information Placard 5 Example Tire Placard Location (B-Pillar) Tire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires.
412 STARTING AND OPERATING Loading To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
STARTING AND OPERATING 413 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • If your vehicle will be towing a trailer, load from your “XXX” amount equals 1,400 lbs (635 kg) and there will trailer will be transferred to your vehicle.
414 STARTING AND OPERATING
STARTING AND OPERATING 415 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
416 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Fuel Economy Underinflated tires will increase tire rolling resistance resulting in higher fuel consumption.
STARTING AND OPERATING 417 (1.6 km) after sitting for a minimum of three hours. The cold tire inflation pressure must not exceed the maximum infla• Check and adjust tire pressure with a good quality tion pressure molded into the tire sidewall. pocket-type pressure gauge. Do not make a visual judgement when determining proper inflation.
418 STARTING AND OPERATING Tire Pressures For High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds and WARNING! within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle important. Increased tire pressure and reduced vehicle poorly.
STARTING AND OPERATING 419 • The puncture is no greater than a ¼ of an inch (6 mm). Summer Or Three Season Tires — If Equipped Consult an authorized tire dealer for tire repairs and Summer tires provide traction in both wet and dry conditions, and are not intended to be driven in snow or additional information. on ice.
420 STARTING AND OPERATING WARNING! Do not use summer tires in snow/ice conditions. You could lose vehicle control, resulting in severe injury or death. Driving too fast for conditions also creates the possibility of loss of vehicle control. Snow Tires Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h).
STARTING AND OPERATING 421 Run Flat tire reaches the run flat mode it has limited driving capabilities and needs to be replaced immediately. A Run Flat tire is not repairable. It is not recommended driving a vehicle loaded at full capacity or to tow a trailer while a tire is in the run flat mode. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with a compact or limited-use temporary spare installed. Damage to the vehicle may result.
422 STARTING AND OPERATING Do not install more than one compact spare tire and The compact spare is for temporary emergency use only. wheel on the vehicle at any given time. You can identify if your vehicle is equipped with a WARNING! compact spare by looking at the spare tire description on the Tire and Loading Information Placard located on the Compact spares are for temporary emergency use driver’s side door opening or on the sidewall of the tire. only.
STARTING AND OPERATING 423 spare tire needs to be replaced. Since it is not the same as your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. Limited-Use Spare — If Equipped The limited-use spare tire is for temporary emergency use only. This tire is identified by a label located on the limited-use spare wheel. This label contains the driving limitations for this spare.
424 STARTING AND OPERATING Tire Spinning Tread Wear Indicators When stuck in mud, sand, snow, or ice conditions, do not Tread wear indicators are in the original equipment tires spin your vehicle’s wheels above 30 mph (48 km/h) or to help you in determining when your tires should be for longer than 30 seconds continuously without stop- replaced. ping. Refer to “Freeing A Stuck Vehicle” in “What To Do In Emergencies” for further information. WARNING! Fast spinning tires can be dangerous.
STARTING AND OPERATING 425 These indicators are molded into the bottom of the tread • Performance tires, tires with a speed rating of V or higher, and summer tires typically have a reduced grooves. They will appear as bands when the tread depth tread life. Rotation of these tires per the vehicle mainbecomes a 1/16 of an inch (2 mm). When the tread is tenance schedule is highly recommended. worn to the tread wear indicators, the tire should be replaced.
426 STARTING AND OPERATING wear and correct cold tire inflation pressures. The manu- you may have on tire specifications or capability. Failure facturer strongly recommends that you use tires equiva- to use equivalent replacement tires may adversely affect lent to the originals in size, quality and performance the safety, handling, and ride of your vehicle. when replacement is needed. Refer to the paragraph on “Tread Wear Indicator.
STARTING AND OPERATING 427 WARNING! (Continued) • Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have a collision. • Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.
428 STARTING AND OPERATING CAUTION! CAUTION! (Continued) To avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted traction device clearance between tires and other suspension components, it is important that only traction devices in good condition are used. Broken devices can cause serious damage. Stop the vehicle immediately if noise occurs that could indicate device breakage. Remove the damaged parts of the device before further use.
STARTING AND OPERATING 429 tires. Rotation will increase tread life, help to maintain mud, snow and wet traction levels, and contribute to a smooth, quiet ride. Refer to the “Maintenance Schedule” for the proper maintenance intervals. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed. The suggested rotation method is the “forward cross” shown in the following diagram. This rotation pattern does not apply to some directional tires that must not be reversed.
430 STARTING AND OPERATING The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12°F (6.5°C). This means that when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure. This is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three hour period.
STARTING AND OPERATING 431 For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 30 psi (207 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 27 psi (186 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressure to approximately 23 psi (158 kPa). This tire pressure is sufficiently low enough to turn ON the “TPM Telltale Light.
432 STARTING AND OPERATING • The TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain • The TPMS is not intended to replace normal tire care correct tire pressure using an accurate tire pressure and maintenance or to provide warning of a tire failure gauge, even if under-inflation has not reached the level or condition. to trigger illumination of the “TPM Telltale Light.
STARTING AND OPERATING 433 • Four TPM sensors, • Various TPMS messages, which display in the Driver Information Display (DID), and • TPM Telltale Light Tire Pressure Monitoring Low Pressure Warnings The “TPM Telltale Light” will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires.
434 STARTING AND OPERATING the vehicle’s recommended cold placard pressure inflation value as shown in the #Inflate Tire to XX# message. Once the system receives the updated tire pressures, the system will automatically update, the graphic display in the DID will return the pressure values shown to their original color, and the “TPM Telltale Light” will turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information.
STARTING AND OPERATING 435 The DID will also display a #SERVICE TPM SYSTEM# sound. In addition, the graphic in the DID will still message for a minimum of five seconds when a system display the low pressure values in a different color and fault related to an incorrect sensor location fault is the #Inflate Tire to XX# message. detected. In this case, the #SERVICE TPM SYSTEM# 3.
436 STARTING AND OPERATING 5. Once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically. In addition, the “TPM Telltale Light” will turn OFF and the graphic in the DID will display a new pressure value instead of dashes (- -), as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires.
STARTING AND OPERATING 437 Light spark knock at low engine speeds is not harmful to 5.7L Engine (With Automatic Transmission) your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is The 5.7L engine (with automatic transmisrequired. Poor quality gasoline can cause problems such sion) is designed to meet all emissions as hard starting, stalling, and hesitations.
438 STARTING AND OPERATING Over 40 auto manufacturers worldwide have issued and 6.4L Engine endorsed consistent gasoline specifications (the World Wide Fuel Charter, WWFC) which define fuel properties The 6.4L engine is designed to meet all necessary to deliver enhanced emissions, performance, emissions regulations and provide exceland durability for your vehicle.
STARTING AND OPERATING 439 necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as 10% ethanol, MTBE, and ETBE. Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions.
440 STARTING AND OPERATING Problems that result from using methanol/gasoline or E-85 To fix a Non-FFV vehicle inadvertently fueled once with ethanol blends are not the responsibility of the manufac- E-85 perform the following: turer. While MTBE is an oxygenate made from methanol, it • Drain the fuel tank (see your authorized dealer). does not have the negative effects of methanol. • Change the engine oil and oil filter.
STARTING AND OPERATING 441 without MMT be used in your vehicle. The MMT content Fuel System Cautions of gasoline may not be indicated on the gasoline pump, therefore, you should ask your gasoline retailer whether CAUTION! the gasoline contains MMT. MMT is prohibited in Federal Follow these guidelines to maintain your vehicle’s and California reformulated gasoline. performance: Materials Added To Fuel • The use of leaded gas is prohibited by Federal law.
442 STARTING AND OPERATING CAUTION! (Continued) • The use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer. NOTE: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.
STARTING AND OPERATING 443 WARNING! (Continued) • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the trunk closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle.
444 STARTING AND OPERATING CAUTION! WARNING! (Continued) • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap. • A poorly fitting fuel filler cap could let impurities into the fuel system. • A poorly fitting fuel filler cap may cause the “Malfunction Indicator Light (MIL)” to turn on. • To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
STARTING AND OPERATING 445 Loose Fuel Filler Cap Message VEHICLE LOADING If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a ”gASCAP” message will display in the odometer or a “Check Gascap” message will display in the Driver Information Display (DID). If this occurs, tighten the fuel filler cap properly and press the TRIP ODOMETER button to turn off the message.
446 STARTING AND OPERATING • Gross Axle Weight Rating (GAWR) rear • Vehicle Identification Number (VIN) • Type of Vehicle • Month Day and Hour of Manufacture (MDH) The bar code allows a computer scanner to read the VIN. Gross Vehicle Weight Rating (GVWR) WARNING! Because the front wheels steer the vehicle, it is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded.
STARTING AND OPERATING 447 Figure out the weight on the front and rear of the vehicle NOTE: Refer to the “Vehicle Certification Label” affixed separately. It is important that you distribute the load to the rear of the driver’s door for your vehicle’s GVWR and GAWRs. evenly over the front and rear axles. Overloading can cause potential safety hazards and TRAILER TOWING shorten useful service life.
448 STARTING AND OPERATING measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be The following trailer towing related definitions will assist supported by the scale. you in understanding the following information: Gross Combination Weight Rating (GCWR) Gross Vehicle Weight Rating (GVWR) Common Towing Definitions The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight.
STARTING AND OPERATING 449 WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have a collision.
450 STARTING AND OPERATING Weight-Distributing Hitch A weight-distributing system works by applying leverage through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturer’s directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.
STARTING AND OPERATING 451 Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer Hitch Classification Definitions Class Max.
452 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission 3.6L Automatic 5.7L Automatic Max. GTW (Gross Trailer Wt.) 12 sq ft (1.11 sq m) 1,000 lbs (454 kg) 12 sq ft (1.11 sq m) 1,000 lbs (454 kg) Refer to local laws for maximum trailer towing speeds. Frontal Area Max. Tongue Wt.
STARTING AND OPERATING 453 Trailer And Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer collisions.
454 STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to the “Tire and Loading Information” placard for the maximum combined weight of occupants and cargo for your vehicle.
STARTING AND OPERATING 455 WARNING! (Continued) WARNING! (Continued) • When hauling cargo or towing a trailer, do not overload your vehicle or trailer. Overloading can cause a loss of control, poor performance, or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure, or tires. • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch.
456 STARTING AND OPERATING • Proper tire inflation pressures are essential to the safe Towing Requirements — Trailer Brakes and satisfactory operation of your vehicle. Refer to • Do not interconnect the hydraulic brake system or “Tires – General Information” in “Starting And Opervacuum system of your vehicle with that of the trailer. ating” for proper tire inflation procedures. This could cause inadequate braking and possible personal injury.
STARTING AND OPERATING 457 WARNING! CAUTION! (Continued) • Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have a collision. • Towing any trailer will increase your stopping distance. When towing you should allow for additional space between your vehicle and the vehicle in front of you. Failure to do so could result in a collision.
458 STARTING AND OPERATING Four-Pin Connector 1 — Female Pins 2 — Male Pin 3 — Ground 4 — Park 5 — Left Stop/Turn 6 — Right Stop/Turn Seven-Pin Connector 1 2 3 4 — — — — Battery Backup Lamps Right Stop/Turn Electric Brakes 5 — Ground 6 — Left Stop/Turn 7 — Running Lamps
STARTING AND OPERATING 459 Towing Tips Electronic Speed Control — If Equipped Before setting out on a trip, practice turning, stopping, • Do not use in hilly terrain or with heavy loads. and backing up the trailer in an area located away from • When using the speed control, if you experience speed heavy traffic. drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. Automatic Transmission — If Equipped The DRIVE range can be selected when towing.
460 STARTING AND OPERATING Highway Driving Cooling System To reduce potential for engine and transmission over- Reduce speed. heating, take the following actions: Air Conditioning City Driving Turn off temporarily. When stopped for short periods, shift the transmission into NEUTRAL and increase engine idle speed. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
STARTING AND OPERATING 461 NOTE: When recreationally towing your vehicle, always follow applicable state and provincial laws. Contact state and provincial Highway Safety offices for additional details. Automatic Transmission — If Equipped CAUTION! Towing this vehicle in violation of the above requirements can cause severe transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty. Recreational towing (with rear wheels on the ground) is NOT ALLOWED.
462 STARTING AND OPERATING CAUTION! Towing this vehicle in violation of the above requirements can cause severe transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty.
WHAT TO DO IN EMERGENCIES CONTENTS ! HAZARD WARNING FLASHERS . . . . . . . . . . .465 ! JACKING AND TIRE CHANGING . . . . . . . . . .479 ! IF YOUR ENGINE OVERHEATS . . . . . . . . . . . .465 ▫ Jack Location/Spare Tire Stowage . . . . . . . . .479 ! TIRE SERVICE KIT — IF EQUIPPED . . . . . . . . .466 ▫ Preparations For Jacking . . . . . . . . . . . . . . . .481 ▫ Tire Service Kit Storage . . . . . . . . . . . . . . . . .467 ▫ Jacking And Changing A Tire . . . . . . . . . . . . .
464 WHAT TO DO IN EMERGENCIES ! MANUAL PARK RELEASE — 8 SPEED TRANSMISSION . . . . . . . . . . . . . . . . . . . . . . .494 ! TOWING A DISABLED VEHICLE . . . . . . . . . . .497 ▫ Automatic Transmission . . . . . . . . . . . . . . . . .498 ▫ Manual Transmission . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES 465 HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel, below the radio. potential for overheating by taking the appropriate action. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all direc- • On the highways — slow down.
466 WHAT TO DO IN EMERGENCIES CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads “H,” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H,” turn the engine off immediately and call for service. WARNING! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.
WHAT TO DO IN EMERGENCIES 467 Tire Service Kit Storage Tire Service Kit Components And Operation The Tire Service Kit is located in the trunk.
468 WHAT TO DO IN EMERGENCIES Using The Mode Select Knob And Hoses Your Tire Service Kit is equipped with the following symbols to indicate the air or sealant mode. Selecting Air Mode Using The Power Button Push and release the Power Button (4) once to turn On the Tire Service Kit. Push and release the Power Button (4) again to turn Off the Tire Service Kit. Push in the Mode Select Knob (5) and turn to this position for air pump operation only.
WHAT TO DO IN EMERGENCIES 469 • When the Tire Service Kit sealant is in a liquid form, clean water, and a damp cloth will remove the material from the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • For optimum performance, make sure the valve stem on the wheel is free of debris before connecting the Tire Service Kit. • You can use the Tire Service Kit air pump to inflate bicycle tires.
470 WHAT TO DO IN EMERGENCIES • Do not lift or carry the Tire Service Kit by the hoses. WARNING! (Continued) WARNING! – If you are unsure of the condition of the tire or the wheel. • Keep Tire Service Kit away from open flames or heat source. • A loose Tire Service Kit thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the Tire Service Kit in the place provided.
WHAT TO DO IN EMERGENCIES 471 WARNING! (Continued) • Take care not to allow the contents of Tire Service Kit to come in contact with hair, eyes, or clothing. Tire Service Kit is harmful if inhaled, swallowed, or absorbed through the skin. It causes skin, eye, and respiratory irritation. Flush immediately with plenty of water if there is any contact with eyes or skin. Change clothing as soon as possible, if there is any contact with clothing. • Tire Service Kit Sealant solution contains latex.
472 WHAT TO DO IN EMERGENCIES (B) Setting Up To Use Tire Service Kit: (C) Injecting Tire Service Kit Sealant Into The Deflated Tire: 1. Push in the Mode Select Knob (5) and turn to the • Always start the engine before turning ON the Tire Sealant Mode position. Service Kit. 2. Uncoil the Sealant Hose (6) and then remove the cap NOTE: Manual transmission vehicles must have the from the fitting at the end of the hose. parking brake engaged and the shift lever in NEUTRAL. 3.
WHAT TO DO IN EMERGENCIES 473 If the sealant (white fluid) does not flow within 0 – 10 NOTE: If the Mode Select Knob (5) is on Air Mode and seconds through the Sealant Hose (6): the pump is operating, air will dispense from the Air Pump Hose (7) only, not the Sealant Hose (6). 1. Press the Power Button (4) to turn Off the Tire Service Kit. Disconnect the Sealant Hose (6) from the valve If the sealant (white fluid) does flow through the stem. Make sure the valve stem is free of debris.
474 WHAT TO DO IN EMERGENCIES latch pillar (recommended pressure). Check the tire 3. Immediately disconnect the Sealant Hose (6) from the pressure by looking at the Pressure Gauge (3). valve stem, reinstall the cap on the fitting at the end of the hose, and place the Tire Service Kit in the vehicle If the tire does not inflate to at least 26 psi (1.8 Bar) storage location. Quickly proceed to (D) “Drive Vepressure within 15 minutes: hicle.” • The tire is too badly damaged.
WHAT TO DO IN EMERGENCIES 475 (D) Drive Vehicle: (E) After Driving: Immediately after injecting sealant and inflating the tire, Pull over to a safe location. Refer to “Whenever You Stop drive the vehicle 5 miles (8 km) or 10 minutes to ensure to Use Tire Service Kit” before continuing. distribution of the Tire Service Kit Sealant within the tire. 1. Push in the Mode Select Knob (5) and turn to the Air Do not exceed 55 mph (90 km/h). Mode position.
476 WHAT TO DO IN EMERGENCIES If the tire pressure is 19 psi (1.3 Bar) or higher: 5. Remove the Speed Limit sticker from the instrument panel after the tire has been repaired. 1. Press the Power Button (4) to turn on Tire Service Kit and inflate the tire to the pressure indicated on the tire 6. Replace the Sealant Bottle (1) and Sealant Hose (6) and loading information label on the driver-side door assembly at your authorized dealer as soon as posopening. sible.
WHAT TO DO IN EMERGENCIES 477 4. Clean any remaining sealant from the Tire Service Kit WHEEL AND TIRE TORQUE SPECIFICATIONS housing. Proper lug nut/bolt torque is very important to ensure 5. Position the new Sealant Bottle (1) in the housing so that the wheel is properly mounted to the vehicle. Any that the Sealant Hose (6) aligns with the hose slot in time a wheel has been removed and reinstalled on the the front of the housing.
478 WHAT TO DO IN EMERGENCIES Wheel Mounting Surface Torque Patterns Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. WARNING! After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury.
WHAT TO DO IN EMERGENCIES 479 JACKING AND TIRE CHANGING WARNING! (Continued) WARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack.
480 WHAT TO DO IN EMERGENCIES Opening The Access Panel 3. Remove the fastener securing the spare tire. Spare Tire Fastener 4. Remove the spare tire. 5. Remove the fastener securing the jack.
WHAT TO DO IN EMERGENCIES 481 WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. Preparations For Jacking Jack Fastener 6. Remove the jack and lug wrench assembly from under the spare tire. Turn the jack screw to the left to loosen the lug wrench, and remove the wrench from the jack assembly. 1.
482 WHAT TO DO IN EMERGENCIES 2. Turn on the Hazard Warning flasher. 3. Set the parking brake. 4. Place the shift lever into PARK (automatic transmission) or 1st gear (manual transmission). 5. Turn OFF the ignition. 6. Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked.
WHAT TO DO IN EMERGENCIES 483 WARNING! (Continued) CAUTION! • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway, be extremely careful of motor traffic.
484 WHAT TO DO IN EMERGENCIES 2. If equipped with aluminum wheels where the center cap covers the lug nuts, use the lug wrench to pry the center cap off carefully before raising the vehicle. 3. Before raising the vehicle, use the lug wrench to loosen, but not remove, the lug nuts on the wheel with the flat tire. Turn the lug nuts counterclockwise one turn while the wheel is still on the ground. 4. Place the jack underneath the lift area that is closest to the flat tire.
WHAT TO DO IN EMERGENCIES 485 WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and tire. 7. Mount the spare tire. CAUTION! Rear Jacking Location 5. Raise the vehicle just enough to remove the flat tire and install the spare tire. Be sure to mount the spare tire with the valve stem facing outward.
486 WHAT TO DO IN EMERGENCIES NOTE: • For vehicles so equipped, do not attempt to install a center cap or wheel cover on the compact spare. • Refer to “Compact Spare Tire” and to “Limited-Use Spare” under “Tires—General Information” in “Starting And Operating” for additional warnings, cautions, and information about the spare tire, its use, and operation. 8. Install the lug nuts with the cone shaped end of the lug nut toward the wheel. Lightly tighten the lug nuts.
WHAT TO DO IN EMERGENCIES 487 9. Lower the vehicle to the ground by turning the jack 2. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the handle counterclockwise. lug nuts. 10. Refer to “Torque Specifications” in this section for proper lug nut torque. 11. Stow the jack, tools and flat tire. Make sure the base of the jack faces the front of the vehicle before tightening down the fastener.
488 WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES If your vehicle has a discharged battery it can be jumpstarted using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump-starting can be dangerous if done improperly so please follow the procedures in this section carefully. NOTE: When using a portable battery booster pack follow the manufacturer’s operating instructions and precautions.
WHAT TO DO IN EMERGENCIES 489 Preparations For Jump-Start The battery is stored under an access cover in the trunk. Remote battery posts are located on the right side of the engine compartment for jump-starting.
490 WHAT TO DO IN EMERGENCIES WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
WHAT TO DO IN EMERGENCIES 491 CAUTION! WARNING! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Do not connect the jumper cable to the negative (-) post of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. Only use the specific ground point, do not use any other exposed metal parts. Connecting The Jumper Cables 1.
492 WHAT TO DO IN EMERGENCIES 2. Disconnect the opposite end of the negative (-) jumper cable from the negative (-) post of the booster battery. 3. Disconnect the positive (+) end of the jumper cable from the positive (+) post of the booster battery. CAUTION! (Continued) the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. 4.
WHAT TO DO IN EMERGENCIES 493 NOTE: For vehicles with automatic transmission: Shifts between DRIVE and REVERSE can only be achieved at wheel speeds of 5 mph (8 km/h) or less. Whenever the transmission remains in NEUTRAL for more than 2 seconds, you must press the brake pedal to engage DRIVE or REVERSE. NOTE: Press the #ESC Off# switch to place the Electronic Stability Control (ESC) system in #Partial Off# mode before rocking the vehicle.
494 WHAT TO DO IN EMERGENCIES WARNING! WARNING! (Continued) Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck and do not let anyone near a spinning wheel, no matter what the speed. Release.
WHAT TO DO IN EMERGENCIES 495 6 Console Storage Bin Locking Tab 3. Using a small screwdriver or similar tool, fish the 5. While holding the locking tab in the disengaged tether strap up through the opening in the console position, pull the tether strap to rotate the lever up and base. rearward until it locks in place in the vertical position. The vehicle is now out of PARK and can be towed. 4.
496 WHAT TO DO IN EMERGENCIES To Reset The Manual Park Release: 1. Push the latch (at the base of the lever, on the rear side) rearward (away from the lever) to unlatch the lever. 2. Rotate the Manual Park Release lever forward and down, to its original position, until the locking tab snaps into place to secure the lever. 3. Pull up gently on the tether strap to confirm that the lever is locked in its stowed position. Tether Strap 4. Tuck the tether strap into the base of the console.
WHAT TO DO IN EMERGENCIES 497 TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service.
498 WHAT TO DO IN EMERGENCIES Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equipment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members of the vehicle, not to bumpers or associated brackets. State and local laws regarding vehicles under tow must be observed.
WHAT TO DO IN EMERGENCIES 499 • The towing distance must not exceed 30 miles (48 km). Manual Transmission • The towing speed must not exceed 30 mph (48 km/h). The manufacturer recommends towing your vehicle with all four wheels OFF the ground using a flatbed.
500 WHAT TO DO IN EMERGENCIES CAUTION! Towing this vehicle in violation of the above requirements can cause severe engine and/or transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE CONTENTS ! ENGINE COMPARTMENT — 3.6L . . . . . . . . . .503 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . .510 ! ENGINE COMPARTMENT — 5.7L . . . . . . . . . .504 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . .515 ! ENGINE COMPARTMENT — 6.4L (392 HEMI) . . .505 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . .515 ! ONBOARD DIAGNOSTIC SYSTEM — OBD II . .506 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . .
502 MAINTAINING YOUR VEHICLE ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . .532 ▫ Clutch Hydraulic System — Manual Transmission (If Equipped). . . . . . . . . . . . . . . . . . . . . . . . .534 ▫ Low Beam Headlamp, High Beam Headlamp, Park/Turn Lamp — Models with Halogen Headlamps — If Equipped . . . . . . . . . . . . . . .558 ▫ Automatic Transmission — If Equipped . . . . .
MAINTAINING YOUR VEHICLE 503 ENGINE COMPARTMENT — 3.
504 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 5.
MAINTAINING YOUR VEHICLE 505 ENGINE COMPARTMENT — 6.
506 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 507 turn off the message. If the problem continues, the serviced, recently had a dead battery or a battery replacemessage will appear the next time the vehicle is started. ment. If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test. A loose, improperly installed, or damaged fuel filler cap may also turn on the MIL. Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station.
508 MAINTAINING YOUR VEHICLE 3. Approximately 15 seconds later, one of two things will system to update. A recheck with the above test routine happen: may then indicate that the system is now ready. • The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station.
MAINTAINING YOUR VEHICLE 509 DEALER SERVICE MAINTENANCE PROCEDURES Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these Service Manuals before attempting any procedure yourself. The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle.
510 MAINTAINING YOUR VEHICLE CAUTION! (Continued) • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or air conditioning. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE 511 regular intervals, such as every fuel stop. The best time to Change Engine Oil — 3.6L and 5.7L Engine check the engine oil level is about five minutes after a The oil change indicator system will remind you that it is fully warmed engine is shut off. time to take your vehicle in for scheduled maintenance. Checking the oil while the vehicle is on level ground will Refer to the “Maintenance Schedule” for further informaimprove the accuracy of the oil level readings.
512 MAINTAINING YOUR VEHICLE Engine Oil Selection — 3.6L and 5.7L Engine For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API Certified and meet the requirements of Chrysler Material Standard MS-6395. Engine Oil Selection — 6.
MAINTAINING YOUR VEHICLE 513 CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New Vehicle Limited Warranty. NOTE: MOPAR® SAE 5W-30 engine oil approved to Chrysler Material Standard MS-6395 such as Pennzoil®, Shell Helix® or equivalent may be used when SAE 5W-20 engine oil meeting MS-6395 is not available. Engine Oil Viscosity — 5.7L Engine Engine Oil Viscosity — 3.
514 MAINTAINING YOUR VEHICLE NOTE: Vehicles equipped with a 5.7L engine must use SAE 5W-20 oil. Failure to do so may result in improper operation of the Fuel Saver Technology. Refer to “Fuel Saver Technology – If Equipped” in “Starting and Operating” for further information. Materials Added To Engine Oil The engine oil filler cap also shows the recommended engine oil viscosity for your engine.
MAINTAINING YOUR VEHICLE 515 station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced with a new filter at every engine oil change. Engine Oil Filter Selection WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.
516 MAINTAINING YOUR VEHICLE Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic maintenance required. NOTE: The battery is stored under an access cover in the trunk. Remote battery terminals are located in the engine compartment for jump-starting. Refer to “Jump-Starting Procedures” in “What To Do In Emergencies” for further information.
MAINTAINING YOUR VEHICLE 517 WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
518 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance WARNING! (Continued) For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. • The air conditioning system contains refrigerant under high pressure.
MAINTAINING YOUR VEHICLE 519 Protection Agency and is an ozone-saving product. How- NOTE: Use only manufacturer approved A/C system ever, the manufacturer recommends that air conditioning PAG compressor oil and refrigerants. service be performed by authorized dealer or other A/C Air Filter service facilities using recovery and recycling equipment.
520 MAINTAINING YOUR VEHICLE Access Door 2. Unsnap both ends and lift the filter access cover. Filter Access Cover 3. Remove the used filter. 4. Install the new filter with arrows pointing in the direction of airflow, which is toward the rear of the vehicle (text and arrows on the filter will indicate this).
MAINTAINING YOUR VEHICLE 521 Body Lubrication A/C Air Filter 5. Close the filter access cover. Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, decklid, sliding doors and hood hinges, should be lubricated periodically with a lithium based grease, such as MOPAR® Spray White Lube to assure quiet, easy operation and to protect against rust and wear.
522 MAINTAINING YOUR VEHICLE Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumulations of salt or road film. Adding Washer Fluid The windshield washer fluid reservoir is located in the front of the engine compartment. Be sure to check the fluid level at regular intervals.
MAINTAINING YOUR VEHICLE 523 The fluid reservoir will hold nearly 1 gal (4 L) of washer have an authorized technician inspect the complete exfluid when the message “Low Washer Fluid” appears in haust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams the Driver Information Display (DID). or loose connections could permit exhaust fumes to seep into the passenger compartment.
524 MAINTAINING YOUR VEHICLE WARNING! (Continued) CAUTION! (Continued) • A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. • Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
MAINTAINING YOUR VEHICLE 525 NOTE: Intentional tampering with emissions control • Do not idle the engine with any spark plug wires systems can result in civil penalties being assessed disconnected or removed, such as when diagnostic against you. testing, or for prolonged periods during very rough idle or malfunctioning operating conditions.
526 MAINTAINING YOUR VEHICLE Coolant Checks Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or place the ignition in the LOCK position (OFF position for Keyless Enter-N-Go™). The fan is temperature controlled and can start at any time the ignition switch is in the ON position (RUN position for Keyless EnterN-Go™). • You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.
MAINTAINING YOUR VEHICLE 527 drain from the coolant recovery bottle. DO NOT REMOVE THE COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS HOT. Cooling System — Drain Flush And Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of old engine coolant (antifreeze).
528 MAINTAINING YOUR VEHICLE CAUTION! (Continued) • Do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended.
MAINTAINING YOUR VEHICLE 529 (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated. NOTE: have a authorized dealer drain, flush, and refill with OAT coolant (conforming to MS.90032) as soon as possible.
530 MAINTAINING YOUR VEHICLE WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
MAINTAINING YOUR VEHICLE 531 of this. As long as the engine operating temperature is • Do not overfill the coolant expansion bottle. satisfactory, the coolant bottle need only be checked once • Check the coolant freeze point in the radiator and in a month. the coolant expansion bottle.
532 MAINTAINING YOUR VEHICLE • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emissions. WARNING! Riding the brakes can lead to brake failure and possibly a collision.
MAINTAINING YOUR VEHICLE 533 Overfilling of fluid is not recommended because it may cause leaking in the system. WARNING! Add enough fluid to bring the level up to the requirements described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear. However, low fluid level may be caused by a leak and a checkup may be needed. • Use only manufacturer’s recommended brake fluid.
534 MAINTAINING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a collision.
MAINTAINING YOUR VEHICLE 535 Manual Transmission — If Equipped Change Transmission Fluid Fluid Level Check If contaminated with water, change the fluid immediately. See your authorized dealer for service. Check the fluid level by removing the fill plug on the left side of the transmission. The fluid level should be 1/4 inch (6.4mm) below the bottom of the fill hole. Add fluid, if necessary, to maintain the proper level.
536 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for fluid specifications. Do not use chemical flushes in your transmission as the chemicals can damage your transmission components. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE 537 CAUTION! If a transmission fluid leak occurs, visit your authorized dealer immediately. Severe transmission damage may occur. Your authorized dealer has the proper tools to adjust the fluid level accurately. Rear Axle Fluid Level Check Checking the fluid level while the vehicle is on level ground and has been stationary for 15 minutes will improve the accuracy of the fluid level reading. Check the fluid level by removing the fill plug on the axle.
538 MAINTAINING YOUR VEHICLE Appearance Care And Protection From Corrosion What Causes Corrosion? Protection Of Body And Paint From Corrosion Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. Vehicle body care requirements vary according to geographic locations and usage.
MAINTAINING YOUR VEHICLE 539 • If insects, tar, or other similar deposits have accumu- Special Care lated on your vehicle, use MOPAR® Super Kleen Bug • If you drive on salted or dusty roads or if you drive and Tar Remover to remove. near the ocean, hose off the undercarriage at least once a month. • Use a high quality cleaner wax, such as MOPAR® Cleaner Wax to remove road film, stains and to protect • It is important that the drain holes in the lower edges your paint finish.
540 MAINTAINING YOUR VEHICLE • If you carry special cargo such as chemicals, fertilizers, NOTE: If your vehicle is equipped with Dark Vapor or de-icer salt, etc., be sure that such materials are well Black Satin Chrome wheels DO NOT USE wheel cleaners, abrasives or polishing compounds. They will permapackaged and sealed. nently damage this finish and such damage is not cov• If a lot of driving is done on gravel roads, consider ered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE 541 Stain Repel Fabric Cleaning Procedure — If Equipped Interior Care Use MOPAR® Total Clean to clean fabric upholstery and Stain Repel seats may be cleaned in the following man- carpeting. ner: Use MOPAR® Total Clean to clean vinyl upholstery. • Remove as much of the stain as possible by blotting MOPAR® Total Clean is specifically recommended for with a clean, dry towel. leather upholstery. • Blot any remaining stain with a clean, damp towel.
542 MAINTAINING YOUR VEHICLE WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. CAUTION! Do not use Alcohol and Alcohol-based and/or Keton based cleaning products to clean leather seats, as damage to the seat may result. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing.
MAINTAINING YOUR VEHICLE 543 Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft cloth.
544 MAINTAINING YOUR VEHICLE FUSES WARNING! (Continued) WARNING! • When replacing a blown fuse, always use an appropriate replacement fuse with the same amp rating as the original fuse. Never replace a fuse with another fuse of higher amp rating. Never replace a blown fuse with metal wires or any other material. Failure to use proper fuses may result in serious personal injury, fire and/or property damage.
MAINTAINING YOUR VEHICLE 545 CAUTION! Front Power Distribution Center • When installing the power distribution center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating.
546 MAINTAINING YOUR VEHICLE Cavity 1 2 3 Cartridge Fuse – 40 Amp Green 50 Amp Red Mini-Fuse – – – 4 5 6 7 8 9 10 11 12 13 14 30 Amp Pink 40 Amp Green 30 Amp Pink – 20 Amp Blue – – – – – – – – – – – 20 Amp Yellow 10 Amp Red 20 Amp Yellow 10 Amp Red – – Description Fuse – Spare Radiator Fan #1 – If Equipped Power Steering #1 / Radiator Fan (6.
MAINTAINING YOUR VEHICLE 547 Cavity 15 16 18 19 Cartridge Fuse – – 40 Amp Green 50 Amp Red Mini-Fuse 20 Amp Yellow 20 Amp Yellow – – 20 21 22 30 Amp Pink 30 Amp Pink 40 Amp Green / 20 Amp Blue – Police 30 Amp Pink 20 Amp Blue – – – – – – – 23 24 28 29 30 31 – – – 15 Amp Blue – 25 Amp Clear Description Left HID – If Equipped Right HID – If Equipped Radiator Fan #2 – If Equipped Power Steering #2 / Radiator Fan (6.
548 MAINTAINING YOUR VEHICLE Cavity 32 33 34 35 36 37 38 39 48 Cartridge Fuse – – – – – – – – – Mini-Fuse – – 25 Amp Clear 20 Amp Yellow 10 Amp Red 10 Amp Red 10 Amp Red 10 Amp Red 10 Amp Red 49 50 51 52 53 – – – – – – – 20 Amp Yellow 10 Amp Red – Description Fuse – Spare Fuse – Spare Powertrain #1 Powertrain #2 Anti-Lock Brake Module Engine Controller/Rad Fan Relays – If Equipped Airbag Module Power Steering Module/AC Clutch Relay AWD Module/Front Axle Disconnect (LX) / Adaptive Cruise (LA) – If Equ
MAINTAINING YOUR VEHICLE 549 Rear Power Distribution Center (Fuses) There is also a power distribution center located in the trunk under the spare tire access panel. This center contains fuses and relays.
550 MAINTAINING YOUR VEHICLE CAUTION! • When installing the power distribution center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
MAINTAINING YOUR VEHICLE 551 Cavity 5 6 7 8 9 10 11 12 Cartridge Fuse 30 Amp Pink 40 Amp Green 40 Amp Green 30 Amp Pink 40 Amp Green 30 Amp Pink 30 Amp Pink — Mini-Fuse — — — — — — — 20 Amp Yellow 15 16 17 18 19 20 40 Amp Green 20 Amp Blue — 30 Amp Pink — — — — — — — — Description Sunroof / Dome Lamp – Police Exterior Lighting #1 Exterior Lighting #2 Interior Lighting Power Locks Driver Door Control Module Passenger Door Control Module Dual USB Center Console Rear/Cigar Lighter IP – If Equipped HVAC
552 MAINTAINING YOUR VEHICLE Cavity 21 22 Cartridge Fuse 30 Amp Pink (6.2L Supercharged) 25 Amp Clear (LD STD) — 23 24 25 26 — — — — 27 31 — — Mini-Fuse — 20 Amp Yellow – Police 10 Amp Red – LA 10 Amp Red 15 Amp Blue 10 Amp Red 15 Amp Blue – LD/LX 25 Amp Clear – LA 30 Amp Green – LA 6.2L Supercharged 25 Amp Clear 25 Amp Breaker Description Fuel Pump (6.
MAINTAINING YOUR VEHICLE 553 Cavity 32 33 Cartridge Fuse — — Mini-Fuse 15 Amp Blue 15 Amp Blue 34 35 36 37 38 — — — — — 10 Amp Red 5 Amp Tan 15 Amp Blue 20 Amp Yellow 15 Amp Blue – LD/LX 20 Amp Yellow – LA 40 41 42 43 44 — — 30 Amp Pink — — — — — 20 Amp Yellow 10 Amp Red Description HVAC Module/Cluster Ignition Switch/RF hub Module/Steering Column Lock-LX If Equipped Steering Column Module/Clock/Spare – Police Battery Sensor Electronic Exhaust Valve – If Equipped Radio Console Power Outlet/Console
554 MAINTAINING YOUR VEHICLE Cavity 45 Cartridge Fuse — Mini-Fuse 15 Amp Blue 46 47 — — — 10 Amp Red 48 49 50 51 52 — — — — — 20 Amp Yellow — — 20 Amp Yellow 10 Amp Red 53 54 55 56 — — — — 10 Amp Red 10 Amp Red — — Description Cluster / Rearview Mirror / Compass(LDLX)/ Humidity Sensor Fuse — Spare Adaptive Front Lighting / Auto High BEAM / Day Time Running Lamps- If Equipped Active Suspension – SRT Fuse — Spare Fuse — Spare Front Heated Seats – If Equipped Heated Cupholders/Rear Heated Seat Swi
MAINTAINING YOUR VEHICLE 555 Cavity 57 58 59 60 61 62 63 64 65 66 67 68 Cartridge Fuse — — — — — — — — — — — — Mini-Fuse — 10 Amp Red 20 Amp Yellow 5 Amp Tan 20 Amp Yellow — — 25 Amp Breaker 10 Amp Red — 10 Amp Red 10 Amp Red 69 70 — — — — Description Fuse — Spare Airbag Module (LD/LX) Adjustable Pedals – Police Heated Washer Nozzles (LD) Cigar Lighter (LA) – If Equipped Fuse — Spare Fuse — Spare Rear Windows (LD/LX) Airbag Module Fuse — Spare Rain and Light Sensor/Sunroof Dual USB Power Outlet – R/A
556 MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery. • Disconnect the negative cable from the battery. • Anytime you store your vehicle, or keep it out of service (e.g., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.
MAINTAINING YOUR VEHICLE 557 Exterior Bulbs Headlamp – High Intensity Discharge (HID) Halogen Headlamp Front Park/Turn Lamp Front Fog Lamp Front Side Marker Tail Lamp Stop/Turn Lamp Rear Side Marker Bulb Number D3S (Serviced at Authorized Dealer) * HIR2LL LED (Serviced at Authorized Dealer) LED (Serviced at Authorized Dealer) LED (Serviced at Authorized Dealer) LED (Serviced at Authorized Dealer) LED (Serviced at Authorized Dealer) LED (Serviced at Authorized Dealer) Backup Lamp Center High-Mount Stop La
558 MAINTAINING YOUR VEHICLE BULB REPLACEMENT 4. Turn the headlamp access cap counterclockwise to remove. NOTE: Lens fogging can occur under certain atmospheric conditions. This will usually clear as atmospheric 5. Remove bulb by turning it counter clockwise and disconnect. conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually 6. Install new bulb by turning it clockwise and reconnect. accelerate the clearing process. 7.
MAINTAINING YOUR VEHICLE 559 3. Remove one fastener on the lower air box to remove Low Beam Headlamp, High Beam Headlamp, and and access the rear of the headlamp assembly. Park/Turn Lamp — Models with High Intensity Discharge (HID) Headlamps — If Equipped 4. Reach behind the passenger headlamp assembly. HID Headlamps 5. Remove the headlamp cover. The headlamps are a type of high voltage discharge tube. 6.
560 MAINTAINING YOUR VEHICLE NOTE: On vehicles equipped with HID headlamps, when the headlamps are turned on, there is a blue hue to the lamps. This diminishes and becomes more white after approximately 10 seconds, as the system charges. Front/Rear Side Marker Lamp Center Tail/Backup Lamp The Center Tail/Backup Lamp use LED lamps that are not serviceable separately. The Center Tail/Backup Lamp must be replaced as an assembly, see your authorized dealer.
MAINTAINING YOUR VEHICLE 561 FLUID CAPACITIES Fuel (Approximate) All Engines Engine Oil With Filter 3.6 Liter Engine (SAE 5W-20, API Certified) 5.7 Liter Engine (SAE 5W-20, API Certified) 6.4 Liter Engine (SAE 0W-40, Synthetic API Certified) Cooling System* 3.6 Liter Engine (MOPAR® Antifreeze/Engine Coolant 10 Year/150,000 Mile Formula or equivalent) 5.7 Liter Engine (MOPAR® Antifreeze/Engine Coolant 10 Year/150,000 Mile Formula or equivalent) 6.
562 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil – 3.6L & 5.7L Engine Engine Oil – 6.4L Engine Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology). We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395 such as MOPAR®, Pennzoil®, and Shell Helix®.
MAINTAINING YOUR VEHICLE 563 Component Engine Oil Filter Spark Plugs Fuel Selection – 3.6L Engine Fuel Selection – 5.7L Engine With Automatic Transmission Fuel Selection – 5.7L Engine With Manual Transmission & 6.4L Engine Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® Engine Oil Filters. We recommend you use MOPAR® Spark Plugs. We recommend you use 87 Octane 89 Octane recommended — 87 Octane acceptable We recommend you use 91 Octane or higher.
564 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! (Continued) • Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any “globally compatible” coolant (antifreeze).
MAINTAINING YOUR VEHICLE 565 Chassis Component Manual Transmission – If Equipped 8-Speed Automatic Transmission – If Equipped Brake Master Cylinder Rear Axle – If Equipped with Automatic Transmission Rear Axle – If Equipped with Manual Transmission Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® ATF+4® Automatic Transmission Fluid. Use only MOPAR® ZF 8&9 Speed ATF™ Automatic Transmission Fluid, or equivalent.
MAINTENANCE SCHEDULES CONTENTS ! MAINTENANCE SCHEDULE — ! MAINTENANCE SCHEDULE — 6.4L . . . . . . . .574 3.6L AND 5.7L . . . . . . . . . . . . . . . . . . . . . . . .568 ▫ Maintenance Chart — 6.4L . . . . . . . . . . . . . .577 ▫ Maintenance Chart — 3.6L And 5.7L . . . . . . . .
568 MAINTENANCE SCHEDULES The message “Oil Change Required” will be displayed in Your vehicle is equipped with an automatic oil change the DID and a single chime will sound, indicating that an indicator system. The oil change indicator system will oil change is necessary. remind you that it is time to take your vehicle in for Your authorized dealer will reset the oil change indicator scheduled maintenance. message after completing the scheduled oil change.
MAINTENANCE SCHEDULES 569 Once A Month Or Before A Long Trip: • Check engine oil level • Check windshield washer fluid level • Check tire pressure and look for unusual wear or damage. Rotate tires at the first sign of irregular wear, even if it occurs before your next scheduled service. • Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering and fill as needed. • Check function of all interior and exterior lights Required Maintenance Intervals.
570 MAINTENANCE SCHEDULES Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, boot seals and replace if necessary. Inspect the rear axle fluid. Inspect the manual transmission fluid (if equipped), add as necessary.
Inspect the brake linings, replace as necessary. Adjust park brake on vehicles equipped with four wheel disc brakes. Additional Maintenance Replace engine air filter. Replace cabin/air conditioning filter. Replace spark plugs (3.6L engine).
Replace spark plugs (5.7L engine). ** Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first. Change the manual transmission fluid (if equipped) if using your vehicle for any of the following: Most of your driving is at sustained speeds during hot weather, above 90°F (32°C), driving in dusty conditions, or stop and go driving.
Change the rear axle fluid if using your vehicle for any of the following: police, taxi, fleet, offroad, or frequent trailer towing. Inspect and replace PCV valve if necessary.
574 MAINTENANCE SCHEDULES WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident. MAINTENANCE SCHEDULE — 6.
MAINTENANCE SCHEDULES 575 referring to the steps described under “Driver Information Display (DID)” in “Understanding Your Instrument • The oil change indicator message will not monitor the Panel” for further information. time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, At Each Stop For Fuel even if the oil change indicator message is NOT • Check the engine oil level. Refer to “Maintenance illuminated.
576 MAINTENANCE SCHEDULES Once A Month At Each Oil Change • Check tire pressure and look for unusual wear or • Change the engine oil filter. damage. • Inspect the brake hoses and lines. • Inspect the battery, and clean and tighten the terminals as required. CAUTION! • Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and add as needed. • Check all lights and other electrical items for correct operation.
MAINTENANCE SCHEDULES 577 48,000 54,000 60,000 66,000 72,000 78,000 84,000 90,000 96,000 36 42 48 54 60 66 72 78 84 90 96 Or Kilometers: 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 160,000 170,000 180,000 190,000 200,000 210,000 220,000 230,000 240,000 250,000 150,000 42,000 30 70,000 144,000 36,000 24 60,000 138,000 30,000 18 50,000 132,000 24,000 12 40,000 126,000 18,000 6 30,000 120,000 12,000 Or Months: 20,000 114,000 6,0
Or Kilometers: 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 160,000 102 108 114 120 126 132 138 144 150 Inspect the brake linings; replace if necessary. X X X X X X X X X X X X Inspect the CV joints. X X X X X X X X X X X X Inspect the exhaust system. X X X X X X X X X X X Adjust the parking brake on vehicles equipped with four wheel disc brakes.
Or Kilometers: 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 160,000 Inspect the manual transmission fluid (if equipped), add as necessary. X Inspect the rear axle fluid. 102 108 114 120 126 132 138 144 150 X Change the rear axle fluid if using your vehicle for any of the following: police, taxi, fleet or frequent trailer towing.
Or Kilometers: 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 160,000 Inspect front suspension, tie rod ends, and boot seals, for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. X X Replace the engine air cleaner filter. Replace the air conditioning filter.
Or Kilometers: 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 160,000 Replace the spark plugs – 6.4L Engine ** Flush and replace the engine coolant at 120 months if not done at 150,000 miles (240,000 km). ** The spark plug change interval is mileage based only, yearly intervals do not apply.
582 MAINTENANCE SCHEDULES WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS ! SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . .585 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY). . . . . . . . . . . . . . . . . . .587 ▫ Prepare For The Appointment. . . . . . . . . . . . .585 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . .587 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . .585 ! WARRANTY INFORMATION . . . . . . . . . . . . .
584 IF YOU NEED CONSUMER ASSISTANCE ! DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES . . . . . . . . . . . . . . . . .591 ▫ Treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .591 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . .591 ▫ Temperature Grades. . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 585 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment Be Reasonable With Requests If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an appointment.
586 IF YOU NEED CONSUMER ASSISTANCE facilities, factory-trained technicians, special tools, and • Authorized dealer name the latest information to ensure the vehicle is fixed • Vehicle Identification Number (VIN) correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to an authorized dealer service manager first. Most matters can be re- Chrysler Group LLC Customer Center solved with this process. P.O.
IF YOU NEED CONSUMER ASSISTANCE 587 Mexico, D. F. Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered by Bell Canada. For TTY teletypewriter users, dial 711 and for Voice callers, dial 1-800-855-0511 to connect with a Bell Relay Service operator.
588 IF YOU NEED CONSUMER ASSISTANCE The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a service contract that is not a manufacturer’s service contract, and you require service after the manufacturer’s New Vehicle Limited Warranty expires, please refer to the contract documents, and contact the person listed in those documents.
IF YOU NEED CONSUMER ASSISTANCE 589 campaign. However, NHTSA cannot become involved in individual problems between you, your authorized MOPAR® fluids, lubricants, parts, and accessories are dealer, and the manufacturer. available from an authorized dealer. They are recommended for your vehicle in order to help keep the vehicle To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1-888-327-4236 (TTY: 1-800-424- 9153), operating at its best. or go to http://www.safercar.
590 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.
IF YOU NEED CONSUMER ASSISTANCE 591 Call toll free at: Treadwear • 1–800–890–4038 (U.S.) The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
592 IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10
594 INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . . .390 ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . . .394 Adaptive Cruise Control (ACC) (Cruise Control) . . .159 Adding Engine Coolant (Antifreeze) . . . . . . . . . . . .528 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .443 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . .522 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .441 Air bag . . . . . . . . . . . . . . .
INDEX 595 Alterations/Modifications, Vehicle . . . . . . . . . . . . . . .7 Antifreeze (Engine Coolant) . . . . . . . . . . . . . . . . . .527 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .530 Anti-Lock Brake System (ABS) . . . . . . . . . . . . . . . .394 Anti-Lock Warning Light . . . . . . . . . . . . . . . . . . . .227 Appearance Care . . . . . . . . . . . . . . . . . . . . . . . . .538 Arming System (Security Alarm) . . . . . . . . . . . . . . .18 Auto Down Power Windows . . . . .
596 INDEX Anti-Lock (ABS) . . . . . . . . . . . . . . . . . . . . . . . .394 Fluid Check . . . . . . . . . . . . . . . . . . . . . . . . . . .532 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . .532 Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .390 Warning Light . . . . . . . . . . . . . . . . . . . . . . . . .227 Brake/Transmission Interlock . . . . . . . . . . . . . . . . .374 Break-In Recommendations, New Vehicle . . . . . . . . .90 Brightness, Interior Lights . . . .
INDEX 597 Installing Child Restraints Using The Vehicle Seat Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 Lower Anchors And Tethers For Children . . . . . . .77 Older Children And Child Restraints . . . . . . . . . .73 Seating Positions . . . . . . . . . . . . . . . . . . . . . . . .76 Using The Top Tether Anchorage . . . . . . . . . . . . .88 Clean Air Gasoline . . . . . . . . . . . . . . . . . . . . . . . .439 Cleaning Wheels . . . . . . . . . . . . . . . . . . . . . . . . .
598 INDEX Deck Lid, Power Release . . . . . . . . . . . . . . . . . . . . .40 Defroster, Rear Window. . . . . . . . . . . . . . . . . . . . .220 Defroster, Windshield . . . . . . . . . . . . . . . . . . . . . . .95 Delay (Intermittent) Wipers . . . . . . . . . . . . . . . . . .148 Diagnostic System, Onboard . . . . . . . . . . . . . . . . .506 Dimmer Switch, Headlight. . . . . . . . . . . . . . . . . . .144 Dipsticks Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 599 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .497 Emergency Trunk Release . . . . . . . . . . . . . . . . . . . .42 Emission Control System Maintenance . . . . . . . . . .507 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .504 Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .515 Block Heater . . . . . . . . . . . . . . . . . . . . . . . . . .367 Break-In Recommendations . . . . . . . . . . . . . . . . .90 Checking Oil Level . . . . . . .
600 INDEX Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .515 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . .337 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . .515 Engine Oil Disposal . . . . . . . . . . . . . . . . . . . . .514 Flashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .465 Hazard Warning . . . . . . . . . . . . . . . . . . . . . . . .465 Turn Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 601 Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .544 Garage Door Opener (HomeLink®) Gas Cap (Fuel Filler Cap) . . . . . . . Gasoline, Clean Air . . . . . . . . . . . . Gasoline (Fuel) . . . . . . . . . . . . . . . Gasoline, Reformulated . . . . . . . . . Gauges Coolant Temperature . . . . . . . . . Fuel . . . . . . . . . . . . . . . . . . . . . Odometer . . . . . . . . . . . . . . . . . Speedometer . . . . . . . . . . . . . . Tachometer . . . . . . . . . . . . . . . .
602 INDEX Head Rests . . . . . . . . . . . . . . . . . . . . . . . . . . . Heated Mirrors . . . . . . . . . . . . . . . . . . . . . . . . Heater, Engine Block . . . . . . . . . . . . . . . . . . . . High Beam/Low Beam Select (Dimmer) Switch . Hill Start Assist. . . . . . . . . . . . . . . . . . . . . . . . Hitches Trailer Towing . . . . . . . . . . . . . . . . . . . . . . HomeLink® (Garage Door Opener) . . . . . . . . . Hood Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 603 Remote Keyless Entry (RKE) . . . . . . . . . . . . . . . .22 Unlatch The Trunk . . . . . . . . . . . . . . . . . . . . . . .24 Unlock The Doors . . . . . . . . . . . . . . . . . . . . . . .22 Key-In Reminder . . . . . . . . . . . . . . . . . . . . . . . . . .15 Keyless Enter-N-Go . . . . . . . . . . . . . . . . . . . . . . . .33 Keyless Enter-N-Go™ Enter The Trunk . . . . . . . . . . . . . . . . . . . . . . . . .24 Lock The Vehicle’s Doors . . . . . . . . . . . . . . . . . .
604 INDEX Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97 Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145 Fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . .227 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . .138 Security Alarm . . . . . . . . . . . . . . . . . . . . . . . . .227 Headlights On Reminder . . . . . . . . . . . . . . . . . .142 Service . . . . .
INDEX 605 Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . . .521 Vanity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 Lug Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .477 Modifications/Alterations, Vehicle . . . . . . . . . . . . . . .7 Monitor, Tire Pressure System . . . . . . . . . . . . . . . .429 Maintenance Free Battery. . . . . . . . . . . . . . . . . . . .516 MOPAR® Parts. . . . . . . . . . . . . . . . . . . . . . . . . . .
606 INDEX Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .515 Filter Disposal . . . . . . . . . . . . . . . . . . . . . . . . .514 Identification Logo . . . . . . . . . . . . . . . . . . . . . .512 Materials Added to . . . . . . . . . . . . . . . . . . . . . .514 Recommendation . . . . . . . . . . . . . . . . . . . . . . .512 Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . . .514 Viscosity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 607 Pretensioners Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Programmable Electronic Features . . . . . . . . . . . . .260 Programmable Features . . . . . . . . . . . . . . . . . . . . .258 Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . . .418 Radiator Cap (Coolant Pressure Cap) . . . . . . . . . . .529 Radio Operation . . . . . . . . . . . . . . . . . . . . . . . . . .324 Radio Remote Controls . . . . . . . . . . . . . . . . . . . . .
608 INDEX Remote Starting Uconnect® Customer Programmable Features . . .270 Uconnect® Settings . . . . . . . . . . . . . . . . . . . . . .270 Remote Starting System. . . . . . . . . . . . . . . . . . . . . .27 Remote Trunk Release. . . . . . . . . . . . . . . . . . . . . . .40 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . . . . .556 Replacement Keys . . . . . . . . . . . . . . . . . . . . . . . . .17 Replacement Parts. . . . . . . . . . . . . . . . . . . . . . . . .508 Replacement Tires . . . .
INDEX 609 Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 Front Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 Operating Instructions . . . . . . . . . . . . . . . . . . . .48 Pregnant Women . . . . . . . . . . . . . . . . . . . . . . . .52 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Rear Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Reminder . . . .
610 INDEX Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .420 Spare Tire. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .422 Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .562 Specifications Fuel (Gasoline) . . . . . . . . . . . . . . . . . . . . . . . . .562 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .562 Speed Control (Cruise Control). . . . . . . . . . . . . . . .155 Speedometer. . . . . . . . . . . . . . . . . . . . . .
INDEX 611 Time Delay, Headlight . . . . . . . . . . . . . . . . . . . . . .141 Tire and Loading Information Placard . . . . . . . . . . .410 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . .404 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97 Aging (Life of Tires) . . . . . . . . . . . . . . . . . . . . .425 Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . .415 Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .427 Changing .
612 INDEX Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .385 Traction Control . . . . . . . . . . . . . . . . . . . . . . . . . .396 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . .447 Cooling System Tips . . . . . . . . . . . . . . . . . . . . .460 Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .451 Minimum Requirements . . . . . . . . . . . . . . . . . .454 Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 613 Uniform Tire Quality Grades . . . . . . . . . . . . . . . . .591 Washers, Windshield . . . . . . . . . . . . . . . . . . . . . . .148 Unleaded Gasoline . . . . . . . . . . . . . . . . . . . . . . . .436 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .538 Untwisting Procedure, Seat Belt . . . . . . . . . . . . . . . .50 Water Driving Through . . . . . . . . . . . . . . . . . . . . . . . .386 Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
Chrysler Group LLC 15D491-126-AD Fourth Edition Printed in U.S.A.
