SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 3 4 INSTRUMENT PANEL AND CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 5 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications / Alterations . . . . . . . . . . . 6 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . .10 ▫ Manual Door Locks . . . . . . . . . . . . . . . . . . . . .16 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .10 ▫ Power Door Locks . . . . . . . . . . . . . . . . . . . . .17 ▫ Sentry Key — If Equipped . . . . . . . . . . . . . . . .11 ▫ Child Protection Door Lock . . . . . . . . . . . . . . .20 䡵 Ignition And Steering Lock . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Battery Replacement . . . . . . . . . . . . . . . . . . . .26 ▫ Automatic Locking Mode (If Equipped) . . . . . .38 䡵 Security Alarm System — If Equipped . . . . . . . . .27 ▫ Center Lap Belts . . . . . . . . . . . . . . . . . . . . . . .38 ▫ To Set The Alarm . . . . . . . . . . . . . . . . . . . . . .27 ▫ Seat Belt Pretensioners . . . . . . . . . . . . . . . . . . .38 ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . . .73 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 9 ▫ Safety Checks You Should Make Outside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to order duplicate keys from your dealer or a locksmith. If you received your keys without the bag, ask your dealer to give you the number. NOTE: Integrated keys (key and key fob combined) must be cut by the dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SENTRY KEY — IF EQUIPPED With this system, an electronically coded ignition key sends a signal to the vehicle electronics. If the electronics recognizes the signal, the vehicle will start and continue to run. If the system does not recognize the signal, the vehicle will start and run for 2 seconds, then shut off. After six unsuccessful attempts at starting, the system will shut down until the correct key is used.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ⬙Security Light⬙ will illuminate for about 3 seconds when the ignition switch is first turned to the ON position. If the vehicle electronics do not receive a valid signal from the ignition key, the ⬙Security Light⬙ will flash continuously to signal that the vehicle has been immobilized. If the ⬙Security Light⬙ remains on during vehicle operation, it indicates a fault in the system electronics.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Insert the second valid key and switch the ignition to the ON position within 15 seconds. After 10 seconds, a chime will sound and the ⬙Security Light⬙ will begin to flash. Turn the ignition back to the OFF position and remove the second key. 3. Insert a blank Sentry Key into the ignition and switch the ignition to the ON position within 60 seconds of having removed the second key. After 10 seconds, a single chime will sound.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE depress and hold the release button located between the ignition switch and the instrument panel. Turn the ignition key to LOCK and remove the key. Automatic Transmissions In the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your vehicle. It may be difficult to turn the key from the LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until it turns easily.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 ILLUMINATED ENTRY Vehicles Equipped With Power Door Locks All interior lights will illuminate in the vehicle when the doors are unlocked using the key fob. The interior lights will remain on for 30 seconds after the last door is closed, or until all doors are closed and either the ignition is turned to the ON position or a key fob LOCK button is pressed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS WARNING! Manual Door Locks All the doors can be “manually” locked from the inside by pushing down the door lock plunger, located at the rear of the door. Both front doors may be opened from the inside with the door lock plunger in the down or locked position. WARNING! For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Power Door Locks 2 Vehicles equipped with power door locks can be locked or unlocked from inside by either the use of the door lock switches located on the front doors or by pressing the LOCK or UNLOCK buttons on the Remote Keyless Entry key fob.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a safety feature the doors will not lock when using the door lock switches during the following conditions: • The driver’s door is open while the key is in the ignition. Automatic Door Locks If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedure: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The doors of the vehicle must be locked automatically by the Automatic Door Lock feature. 19 3. Insert the key into the ignition. • The vehicle is in P (Park) and the ignition switch is in any key position. 4. Within 10 seconds, cycle the key from the OFF position to the ON position four times ending in the ON position (do not start the engine). This feature will not operate if any of the conditions above are not met or following has occurred: 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the childprotection door lock system. To use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! 21 REMOTE KEYLESS ENTRY Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. 2 NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The line of transmission must not be blocked with metal objects. To unlock the doors: Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, and the parking lights will flash on twice. The system can be programmed to unlock all the doors upon the first UNLOCK button press by using the following procedure: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Horn Chirp Programming The horn chirp feature will be shipped from the assembly plants activated. If desired this feature can be disabled by using the following procedure: 1. Press and hold the LOCK button on the key fob. 2. After holding the LOCK button for four seconds, also press the PANIC button within 6 seconds. A single chime will sound to indicate that this feature has changed. 3. Release both buttons at the same time. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pressing the LOCK button on the key fob, while you are in the vehicle, will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. 5. If the desired programming was not achieved or to reactivate this feature, repeat the above steps.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Weak batteries in transmitter. The expected life of batteries is five years. 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, military base, and some mobile or CB radios. Programming Additional Transmitters Vehicles will be shipped from the assembly plants with two key fob transmitters programmed only for that vehicle. A total of eight fobs can be programmed for your vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 8. Using the fob to be programmed, press and release both the LOCK and UNLOCK buttons, simultaneously for 2 seconds and then release. 9. Press and release the UNLOCK button a single chime will be heard. 10. Repeat steps 8 and 9 to program up to six additional fobs. 11. Turn the ignition to the OFF position. 12. Your vehicle will remain in program mode up to 60 seconds from when the original chime was heard.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To assemble the transmitter case, snap the two halves together. NOTE: If the key fob is equipped with a screw, reinstall and tighten the screw until snug. SECURITY ALARM SYSTEM — IF EQUIPPED This system monitors the vehicle doors and ignition for unauthorized operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Disarm the System: Use the Keyless Entry transmitter to unlock the doors. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors. Check the vehicle for tampering. The security alarm system is designed to protect your vehicle; however, you can create conditions where the system will arm unexpectedly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 WINDOWS Power Windows 2 The control on the left front door has up-down switches that give you finger tip control of all four power windows. There is a single opening and closing switch on the passenger doors for passenger window control.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ignition is turned OFF or the driver’s door is opened. This feature can be turned off by your authorized dealer. NOTE: The Power Accessory Delay feature will allow the power windows to operate for ten minutes after the ignition it turned OFF. Auto Down The driver’s window switch has an Auto Down feature. Push the window switch past the first detent, release, and the window will go down automatically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sliding Rear Window Sliding Window Light Latch A locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window. 31 WIND BUFFETING Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down or partially open.. This is a normal occurrence and can be minimized.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is very dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your dealer and have it fixed. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Push in on the anchorage release button to release the anchorage, and then move it up or down to the position that serves you best. 2 As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Locking Mode (if equipped) To convert from the normal emergency locking mode to the automatic locking mode, grasp the shoulder belt portion and pull all of the webbing out of the retractor. Allow some of the webbing to retract into the retractor, as the belt retracts you will hear a clicking sound to indicate the seat belt is now in the automatic locking mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The pretensioners are triggered by the Occupant Restraint Controller (ORC). Like the airbags, the pretensioners are single use items. After a collision that is severe enough to deploy the airbags and pretensioners, both must be replaced.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled. Seat Belts and Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. 4. Turn off the engine. A single chime will sound to signify that you have successfully completed the programming.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! 41 Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbags Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the instrument panel, above the glove compartment. The words SRS/AIRBAG are embossed on the airbag covers. NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Window bags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. All occupants should use their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the airbag room to inflate. 4. If your vehicle has window bags, do not lean against the door or window, airbags will inflate forcefully into the space between you and the door. 5. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag System Components The airbag system consists of the following: • Occupant Restraint Controller 45 • Driver and Front Passenger Seat Belt Pretensioners • Occupant Classification System (OCS) for the Front Passenger Seat • Side Remote Acceleration Sensors (If Equipped) − Occupant Classification Module • Airbag Warning Light − Passenger Airbag Disable (PAD) Indicator Light • Driver Airbag − Weight Sensors • Passenger Airbag How the Airbag System Wo
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or RUN positions. These include all of the items listed above except the steering wheel and column, and knee bolsters. If the key is in the OFF position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate. During a moderate-to-severe rear impact the ORC may deploy the seat belt pretensioners alone.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint. 47 If the passenger frontal air bag is automatically turned off by the OCS, or by using the manual on/off switch (on vehicles so equipped), the PAD Indicator lamp iluminates the passenger frontal airbag symbol and the word ⬙OFF⬙ to show that the passenger airbag will not inflate during a collision requiring airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For almost all properly installed rear facing child restraints, the PAD indicator light will be illuminated indicating that the front passenger airbag is turned off and will not inflate. If the PAD indicator light is not illuminated, DO NOT assume the air bag is turned off and move the child restraint to the second row of seats (if equipped). A deploying passenger air bag can cause death or serious injury to a child in a rear facing infant seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 the OCS has classified the occupant of the seat as an adult. An adult occupant needs to sit in a normal position (with their feet on or near the floor) in order to be properly classified. Reclining the seat back too far may change how an occupant is classified by the OCS. If the front passenger seat is damaged in any way, it should only be serviced by an authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Indicator Light and the Airbag Warning Light. Once the lodged object is removed, the fault will be automatically cleared after a short period of time. through vent holes in the sides of the airbag. In this way the airbags do not interfere with your control of the vehicle. • The Driver and Passenger Airbag/Inflator Units are located in the center of the steering wheel and the right side of the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 or a weight less than the predetermined threshold, the ORC will not illuminate the PAD indicator light even though the airbag is turned OFF. where the window bag inflates. This especially applies to children. The window bag is only about 3-1/2 inches (9 cm) thick when it is inflated. • Your vehicle has four Weight Sensors located within the seat structure or between the seat tracks and cushion frame.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not modify the front seat center console or center position seat in any way. • Do not use prior or future model year seat covers not designated for the specific model being repaired. Always use the correct seat cover specified for the vehicle. • Do not replace the seat cover with an aftermarket seat cover. Do not add a secondary seat cover other than those approved by DaimlerChrysler/Mopar.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • • • • • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The light remains on or flickers after the 6 to 8 second interval. • The light flickers or comes on and remains on while driving. NOTE: If the speedometer, tachometer or any engine related gauges are not working, the airbag control module may also be disabled. The airbags may not be ready to inflate for your protection. Promptly check fuse block for blown fuses. Refer to the label located on the inside of the fuse block cover for the proper airbag fuses.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Whenever an airbag is turned off, even a lap/ shoulder belted passenger may hit their head, neck, or chest on the dashboard (instrument panel) or windshield in a crash. This may result in serious injury or death. NOTE: The Passenger Airbag On/Off Switch is not available in the Quad Cab.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Shut Off the Passenger Frontal Airbag Place the ignition key in the Passenger Airbag On/Off Switch, push the key in and turn clockwise, and remove the key from the switch. This will shut off the passenger frontal airbag. The passenger frontal airbag symbol and the word “OFF” on the passenger airbag disable (PAD) lamp will illuminate when the ignition switch is turned to the ON position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In the event that an investigation is undertaken by DaimlerChrysler Corporation (regardless of initiative), the company or its designated representative will first obtain permission of the appropriate custodial entity for the vehicle (usually the vehicle owner or lessee) before accessing the electronic data stored, unless ordered to download data by a court with legal jurisdiction (i.e., pursuant to a warrant).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Airbag deployment level (if applicable) • Seatbelt status • Brake status (service and parking brakes) 59 rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front. • Cruise control status There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult seat belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). ⬙Convertible⬙ child seats can be used either rearward-facing or forward-facing in the vehicle. Convertible child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children who weigh more than 20 lbs (9 kg) but are less than one year old.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large for Booster Seats • Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips for getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. The manufacturer recommends that you try a child restraint in the vehicle seats where you will use it before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE provides for the installation of the child restraint without using the vehicle’s seat belts, instead securing the child restraint using lower anchorages and upper tether straps from the child restraint to the vehicle structure. LATCHcompatible child restraint systems are now available.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the vehicle’s seat belt for the outboard position, but you must use the vehicle’s seat belt at the center position. If your child restraints are not LATCH compatible, you can only install the child restraints using the vehicle’s seat belts. Please refer to the next section for typical installation instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE of the seat cushion where it meets the seat back, and are just visible when you lean into the vehicle to install the child restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces. In addition, there are tether strap anchorages each LATCH seating position (see section on Child Restraint Tether Anchor).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing Child Restraints Using the Vehicle Seat Belt The passenger seat belts are equipped with either cinching latch plates or automatic locking retractors, which are designed to keep the lap portion tight around the child restraint so that it should not be necessary to use a locking clip. If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Tether Anchor The Club Cab model has two routing straps located behind each of the rear outboard seating positions. The tether anchor itself is located in the center of vehicle, in between the two seating positions. The front outboard passenger seating position is also equipped with a child tether anchorage, located at the base of the front seat back.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tether Strap at the Front Passenger Seat (Club Cab) 1. Route the child restraint tether strap up and over the front passenger seat back and under the head restraint. 2. Connect the tether strap to the lower anchor. 3. Remove the slack in the tether strap so that it is pulled tight.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Tether Straps at the Rear Passenger Seat (Club Cab) 1. Route the child restraint tether strap through the routing loop, located directly behind the child restraint. The routing loops are located behind the flip-down door on the cab back panel (padded bolster). 2. Route the tether strap across to the center tether anchorage. The center tether is located behind the slide door in the center of the vehicle, between the two seating positions. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE through the anchor strap outer loop (webbing material loop), located directly behind the child restraint. 2. Route the tether strap across to the nearest installed anchor strap, and attach the tether strap hook to the anchor strap inner metal ring. 3. Remove the slack in the tether strap so that both anchor straps are pulled tight. NOTE: Two Anchors must be used for any of the three seating positions. Tether Straps at the Rear Passenger Seat (Quad Cab) 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 2 Multiple Child Restraint Quad Cab
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle. Use only the anchor positions directly behind the child restraint to secure a child restraint top tether strap. See your dealer for help if necessary.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few thousand miles of operation. This is a normal part of the break-in and is not an indication of difficulty. SAFETY TIPS Exhaust System WARNING! Exhaust gases contain carbon monoxide, an extremely toxic gas that by itself is colorless and odorless.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Safety Checks You Should Make Outside The Vehicle: Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Tires Examine tires for tread wear or uneven wear patterns. Check for stones, nails, glass or other objects lodged in the tread.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Fluid Leaks Check the area under vehicle after overnight parking for fuel, water, oil, or other fluid leaks. Also, if gasoline fumes are detected, the cause should be located and corrected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .86 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .81 ▫ Phone Call Features . . . . . . . . . . . . . . . . . . . .92 ▫ Automatic Dimming Mirror — If Equipped . . . .82 ▫ UConnect™ System Features . . . . . . . . . . . . . .95 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Manual Lumbar Support Adjustment — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 ▫ Adjustable Head Restraints — Front Seating Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 ▫ Daytime Running Lights (Canada Only) . . . . . 117 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . 117 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . 117 ▫ Cargo Light — If Equipped . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 ▫ To Set At A Desired Speed . . . . . . . . . . . . . . . 123 ▫ Distance To Empty (DTE) . . . . . . . . . . . . . . . 129 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . . 123 ▫ Trip Odometer (ODO) . . . . . . . . . . . . . . . . . . 130 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . . 124 ▫ Elapsed Time (ET) . . . . . . . . . . . . . . . . . . . . . 130 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Erasing Homelink Buttons . . . . . . . . . . . . . . . 138 䡵 Center Storage Compartment — If Equipped . . . 142 ▫ Reprogramming a Single Homelink Button . . . 138 䡵 Cup Holders . . . . . . . . . . . . . . . . . . . . . . . . . . 143 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 䡵 Tailgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. 81 Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of truck). The mirror should be adjusted while set in the day position (toward windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror will automatically adjust for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Electric Remote-Control Mirrors The controls for the power mirrors are located on the driver’s door trim panel. 3 To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When finished adjusting the mirror, turn the control to the center position to prevent accidentally moving a mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 The UConnect™ phonebook enables you to store up to 32 names and four numbers per name. Each language has a separate 32 name phonebook accessible only in that language. This system is driven through your Bluetooth™ Hands-Free profile cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Profile), you may not be able to use any UConnect™ features. Refer to your cellular service provider or the phone manufacturer for details. • Prior to giving a voice command, one must wait for the voice on beep, which follows the ⬙Ready⬙ prompt or another prompt. The UConnect™ system is fully integrated with the vehicle’s audio system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Command Tree Refer to “Voice Tree” at the end of this section. Help Command If you need assistance at any prompt or if you want to know what your options are at any prompt, say ⬙Help⬙ following the voice on beep. The UConnect™ system will play all the options at any prompt if you ask for help. To activate the UConnect™ system from idle, simply press the ’Phone’ button and follow audible prompts for directions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing.⬙ • When prompted, after the voice on beep, say ⬙Pair a Phone.⬙ • You will be asked to say a four-digit pin number which you will later need to enter into your cellular. You can enter any four-digit pin number. You will not need to remember this pin number after the initial pairing process.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 Dial by Saying a Number Call by Saying a Name • Press the ’Phone’ button to begin. • Press the “Phone” button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Dial.⬙ • After the ⬙Ready⬙ prompt and the following beep, say ⬙Call.⬙ • System will prompt you to say the number you want call. • System will prompt you to say the name of the person you want call. • For example, you can say ⬙234-567-8901.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Add Names to Your UConnect™ Phonebook NOTE: Adding names to phonebook is recommended when vehicle is not in motion. • Press the “Phone” button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook New Entry.⬙ • When prompted, say the name of the new entry. Use of long names helps the voice recognition and is recommended. For example, say ⬙Robert Smith⬙ or ⬙Robert⬙ instead of ⬙Bob.⬙ • When prompted, enter the number designation (e.g.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, mobile, or pager) that you wish to edit. • When prompted, recite the new phone number for the phonebook entry that you are editing. After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE After confirmation, the phonebook entries will be deleted. Note that only the phonebook in the current language is deleted. Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Erase All.⬙ • The UConnect™ system will ask you to verify that you wish to delete all the entries from the phonebook. • After confirmation, the phonebook entries will be deleted.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect™ system will interrupt the vehicle audio system, if on, and will ask if you would like to answer the call. To reject the call, press and hold the ’Phone’ button until you hear a single beep indicating that the incoming call was rejected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Toggling Between Calls If two calls are in progress (one active and one on hold), press the ’Phone’ button until you hear a single beep indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call Continuation Call continuation is progression of a phone call on UConnect™ system after the vehicle ignition key has been switched to off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Emergency Assistance If you are in an emergency and the mobile phone is reachable: The UConnect™ system does slightly lower your chances of successfully making a phone call as to that for the cell phone directly. • Pick up the phone and manually dial the emergency number for your area.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Please refer to the 24-Hour Towing Assistance coverage details in the DaimlerChrysler Corporation 24-Hour Towing Assistance Program Guide. Paging To learn how to page, refer to section ⬙Working with Automated Systems.⬙ Paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the UConnect™ system. Voice Mail Calling To learn how to access your voice mail, refer to section ⬙Working with Automated Systems.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Barge In - Overriding Prompts The ’Voice Recognition’ button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately. For example, if a prompt is playing ⬙Would you like to pair a phone, clear aѧ,⬙ you could press the ’Voice Recognition’ button and say ⬙Pair a Phone⬙ to select that option without having to listen to the rest of the voice prompt.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE may feel that the call did not go through even though the call is in progress. Once your call is answered, you will hear the audio. Mute/Un-mute (Mute off) When you mute the UConnect™ system, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the UConnect™ system: • Press the ’Voice Recognition’ button. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Mute.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you would like to connect or disconnect the Bluetooth™ connection between a UConnect™ paired cellular phone and the UConnect™ system, follow the instruction described in your cellular phone user’s manual. List Paired Cellular Phone Names • Press the ’Phone’ button to begin. • After the “Ready” prompt and the following beep, say “Setup Phone pairing”. • When prompted, say ⬙List Phones⬙.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 • The selected phone will be used for the next phone call. If the selected phone is not available, the UConnect™ system will return to using the highest priority phone present in or near (approximately with in 30 feet) the vehicle. Things You Should Know About Your UConnect™ System Delete UConnect™ Paired Cellular Phones • Speak normally, without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English and Spanish accents, the system may not always work for some. • When navigating through an automated system, such as, voice mail, or when sending a page, at the end of speaking the digit string, make sure to say ⬙send.⬙ • Storing names in phonebook when vehicle is not in motion is recommended.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Performance, such as, audio clarity, echo. and loudness to a large degree, rely on the phone and network, and not the UConnect™ system. • Echo at far end can sometime be reduced by lowering the in-vehicle audio volume. Bluetooth Communication Link Cellular phones have been found to occasionally loose connection to the UConnect™ system. When this happens, the connection can generally be re-established by switching the phone off/on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. Front Seats Manual Seat Recliners The front seats are equipped with recliners.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. Manual Lumbar Support Adjustment — If Equipped The manual lumbar support rotary control adjustment is located on the left side of the driver’s seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To lower the head restraint, depress the release button located at the base of the head restraint and push down on the head restraint. 6 - Way Power Seat Adjuster — Driver’s Side Only The 6-way power seat adjuster switches are on the outboard side of the driver’s seat. Use this switch to move the seat up or down, forward or rearward, or tilt.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 control seat height. Change the seat angle by using the two toggle switches, tilting it up or down. 3 Up, Down, Forward, and Rearward The power seat controls are on the outboard side of the driver’s seat cushion. Three switches control the seat movement. The four-way switch in the center can be moved forward or backwards to get the most comfortable position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Club Cab/Quad Cab Rear Seat More cargo space is available by lifting up on the rear seat cushion. The Quad Cab rear seat is a 60/40 split cushion and full back. Either cushion can be raised independently. TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then push the safety latch lever down while lifting the grille with your right hand. It is located at the top center of the grille just left of center. Lift the hood and gas filled props will hold it open. 113 To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center front edge of the hood to ensure that both latches engage. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Interior Lights Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the second upward detent position, or if equipped, when the UNLOCK button is pressed on the key fob.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE control all the way down to the OFF detent will cause all the interior lights to go out. This is also known as the ⬙Party⬙ mode because it allows the doors to stay open for extended periods of time without discharging the vehicle’s battery. The brightness of the instrument panel lighting can be regulated by rotating the dimmer control up (brighter) or down (dimmer).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlamp Delay To aid in your exit, your vehicle is equipped with a headlamp delay that will leave the headlamps on for 60 seconds. This delay is initiated when the ignition is turned OFF while the headlamp switch is on, and then the headlamp switch is cycled off. The headlamps will remain on for 60 seconds. Headlamp delay can be cancelled by either turning the headlamp switch ON then OFF or by turning the ignition ON.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. Lights-on Reminder If the headlights, parking lights, courtesy lights or cargo lights are left on, after the ignition is turned off, a chime will sound when the driver’s door is opened.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO Light — If Equipped MULTIFUNCTION CONTROL LEVER The multifunction control lever is located on the left side of the steering column. Turn Signals The cargo lights are turned on by pressing on the CARGO button. The interior lights will also turn on when the cargo lights are on. The cargo lights will also turn on for 30 seconds when a key fob Unlock is pressed, as part of the illuminated entry feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The arrow on either side of the instrument cluster flashes to indicate the direction of the turn, and proper operation of the front and rear turn signal lights. If an indicator fails to light when the lever is moved, it would suggest that the switch or indicator lamp is defective. If a defective bulb or wiring circuit is detected for the turn signal system, the arrow indicators will flash at a faster rate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wipers Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range. The delay interval decreases as you rotate the knob until it enters the LO continual speed position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during windshield washer use. NOTE: If the front wiper is operating when the ignition is turned off, the wiper will automatically return to the ⬙Park⬙ position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over accelerator operation at speeds greater than (refer to the table below for the speed for your specific engine). The controls are mounted on the steering wheel. 123 To Activate Push the ON/OFF button to the ON position. In the instrument cluster, the word “CRUISE” illuminates when the system is on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Speed Control ON when not in use is dangerous. You could accidentally set the system to cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you aren’t using it. To Resume Speed To resume a previously set speed, push and release the RESUME button. Resume can be used at any speed above (refer to the table below for the speed for your specific engine).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Functions Engage Speed Minimun RESUME Speed ACCEL Increase DECEL Decrease Dropout Speed 3.7L 30 mph (48 km/h) 25 mph (40 km/h) 2 mph (3km/h) 1 mph (2 km/h) 25 mph (40 km/h) To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy/Reading Lights Near the front of the console are two courtesy/reading lights. Both lights illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (fully upward position), or when the UNLOCK button is pressed on the Remote Keyless Entry transmitter, if so equipped. These lights are also operated individually as reading lights by pressing the recessed area of the corresponding lens.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE RESET Button Use this button to reset the following displays to zero: • Average Fuel Economy • Trip Odometer • Elapsed time. Global Reset If the RESET button and STEP button are pressed at the same time and held for 3 seconds the Global Reset feature will reset the distance to empty (using a default fuel economy value), fuel economy, trip odometer, and elapsed time displays.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Step Button Use this button to choose or cycle through the four trip conditions. 129 Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. This display mode becomes less sensitive to instantaneous changes in fuel consumption as the number of total vehicle miles since the last reset increases.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When Distance To Empty = 0, the fuel gauge pointer will initially be on the red “E” marker. At this point (fuel gauge pointer on the the red “E” marker) there is reserve fuel capacity, which corresponds to approximately 8% of tank volume. This reserve capacity was put in place to prevent the likelihood of customers running out of fuel when operating at maximum load conditions in areas where there aren’t many gas stations.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass/Temperature Display WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible personal injury or property damage. Automatic Compass Calibration This compass is self-calibrating which eliminates the need to manually set the compass.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Put Into a Calibration Mode Turn on the ignition and set the display to “Compass/ Temperature.” Press and hold the RESET button to change the display between VAR (compass variance) and CAL (compass calibration) modes. When the CAL symbol is displayed complete one 360 degree turn in an area free from large metal objects or power lines. The CAL symbol will turn off and the compass will function normally.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press and hold the RESET button approximately five seconds. The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE For additional information on HomeLink威, call 1–800– 355–3515, or on the internet at www.homelink.com. WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects. WARNING! Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run the vehicle’s exhaust while training the transceiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Some gate operators and garage door openers may require you to replace this Programming Step 3 with procedures noted in the ⬙Gate Operator/Canadian Programming⬙ section. 4. The HomeLink indicator light will flash slowly and then rapidly after HomeLink successfully receives the frequency signal from the hand-held transmitter. Release both buttons after the indicator light changes from the slow to the rapid flash. 5.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink should now activate your rolling code equipped device. NOTE: To program the remaining two HomeLink buttons, begin with ⬙Programming⬙ step two. Do not repeat step one. For questions or comments, please contact HomeLink at www.homelink.com or 1-800-355-3515.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties or questions, contact HomeLink at: www.homelink.com or 1-800-3553515.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Security Garage Door Opener Operation with Security Alarm (if equipped) If your vehicle is equipped with the Security Alarm feature, the operation of the HomeLink feature will be purposely inhibited if the Security Alarm is ⬙Armed⬙. This prevents HomeLink operation due to un-authorized vehicle entry. HomeLink operation will be re-stored when the Security Alarm has been ⬙Disarmed⬙. If you sell your vehicle, be sure to erase the frequencies.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE automatically when ready for use. To preserve the heating element, do not hold the lighter in the heating position. Electrical Outlet Use With Engine OFF (Battery Fed Configuration) The console outlet can be reconfigured by the customer to operate only when the ignition is On (switch battery fed) or with the ignition switch On/Off (battery fed) to allow for cellular phone charging and/or operation while the ignition is Off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 FLOOR CONSOLE — IF EQUIPPED • Coin slots Floor Console Features The coin slots are located under the instrument panel center stack.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Outlet and Portable Phone Storage The console is equipped with a power outlet, portable phone storage bin, and phone cord routing. The phone storage bin can be used when ease access to the phone is needed. Also the power outlet inside console compartment can be used to power up the phone while it is being stored in the bin. To use plug in the portable power recharge cord and place the cord along the slot provided in the left side of the console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 CUP HOLDERS If your vehicle has bucket seats with a center console, there are three cup holders located on the console. Refer to the section on floor console. A two-cavity cup holder is available on all Quad Cab with rear seats mounted on the floor. 3 Rear Cup Holders – Quad Cab with Automatic TAILGATE To simplify mounting of a camper unit with an overhang, the tailgate can be removed quickly. Follow these steps: 1. Open the tailgate to a 45° angle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Unclip and remove the cables from the box while maintaining a 45° angle. To reinstall the tailgate, do the following: 1. Slide the tailgate onto the driver’s side pivot. 2. Hold the tailgate at a 45° angle and insert it into the passenger side pivot. 3. Clip the cables to the box. SLIDE-IN CAMPERS 3. Lift the tailgate off of the pivot on the passenger side by pulling upward and rearward at the same time. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information The Manufacturer’s Warranty does not apply to body modifications and special equipment, such as a camper unit, heaters, stoves, refrigerators, etc., supplied by manufacturers other than the manufacturer. For warranty coverage and service on these items, contact the applicable manufacturer. To mount a camper unit with an overhang, the tailgate can be removed. Unlatch tailgate and remove support cables from the retainer pins.
INSTRUMENT PANEL AND CONTROLS CONTENTS 䡵 Instruments And Controls . . . . . . . . . . . . . . . . . 150 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 151 䡵 Instrument Cluster Description . . . . . . . . . . . . . 152 䡵 Radio Reception Information . . . . . . . . . . . . . . . 159 ▫ AM Reception . . . . . . . . . . . . . . . . . . . . . . . 159 ▫ FM Reception . . . . . . . . . . . . . . . . . . . . . . . . 159 䡵 Electronic Digital Clock . . . . . . . . . . . . . . . . . .
INSTRUMENT PANEL AND CONTROLS 䡵 Sales Code RAQ – AM/FM/CD (6-Disc) Radio With Optional Satellite Radio, Hands Free Phone, And Video Capabilities . . . . . . . . . . . . . 166 ▫ Operating Instructions - Radio Mode . . . . . . . 166 ▫ Operation Instructions - (CD Mode For CD Audio Play) . . . . . . . . . . . . . . . . . . . . . . 170 ▫ Load/Eject Button (CD Mode For CD Audio Play) . . . . . . . . . . . . . . . . . . . . . . 172 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . .
INSTRUMENT PANEL AND CONTROLS 149 䡵 Remote Sound System Controls — If Equipped . . 182 䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . . 184 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 183 ▫ Air Conditioning And Heater . . . . . . . . . . . . . 185 ▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . 183 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . . 188 䡵 Compact Disc Maintenance . . . . . . . . . . . . . . . .
INSTRUMENT PANEL AND CONTROLS INSTRUMENTS AND CONTROLS
INSTRUMENT PANEL AND CONTROLS 151 INSTRUMENT CLUSTER 4
INSTRUMENT PANEL AND CONTROLS INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gage The fuel gauge shows level of fuel in tank when ignition switch is in the ON position. (See page 245 for more information.) 2. Temperature Gage The temperature gage indicates engine coolant temperature. Any reading within the normal range indicates that the cooling system is operating satisfactorily.
INSTRUMENT PANEL AND CONTROLS 153 left/right turn signal is left on with the engine RPM vehicle speed greater than 15 mph (24 km/h) for more than one mile. (See page 118 for more information.) 7. Fog Light Indicator — If Equipped This light shows when the fog lights are ON. 4. Low Fuel Warning Light This indicator lights when the fuel gauge reads 1/8 of a tank or less. There is a pointer on the side of this symbol that indicates the side that your fuel filler door is located. 8.
INSTRUMENT PANEL AND CONTROLS CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature light is on, safely pull over and stop the vehicle. Idle the vehicle in neutral with the air conditioner turned off until the light turns off. If the if the light remains on, turn the engine off immediately, and call for service. WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant.
INSTRUMENT PANEL AND CONTROLS 12. ABS Warning Light This light monitors the Anti-Lock Brake System which is described elsewhere in this manual. This light will come on when the ignition key is turned to the ON position and may stay on for approximately 3 seconds. If this light remains on or comes on during driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. See your authorized dealer immediately. 13.
INSTRUMENT PANEL AND CONTROLS U.S. federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. Therefore, if the odometer reading is changed during repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined. 17. Trip Odometer The trip odometer shows individual trip mileage.
INSTRUMENT PANEL AND CONTROLS 21. BRAKE System Warning Light This light will light when the ignition key is turned to the ON position and will remain on for a few seconds. If the light stays on, it may be an indication that the parking brake has not been released, or there is a low brake fluid level. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction.
INSTRUMENT PANEL AND CONTROLS If this light comes on and remains on while driving, it suggests a potential engine control problem and the need for system service. Although your vehicle will usually be drivable and not need towing, see your dealer for service as soon as possible. CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and driveability.
INSTRUMENT PANEL AND CONTROLS 29. Cargo Lamp The Cargo Lamp light will illuminate when the Cargo Lamp is activated from the headlight control switch, located below the headlight switch. 30. TOW/HAUL The TOW/HAUL button is located at the end of the gear shift lever. This light will illuminate when the TOW/ HAUL button has been selected. 31. 4LOCK Indicator Indicates transfer case is in 4LOCK position. 32.
INSTRUMENT PANEL AND CONTROLS ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the frequency and/or time in hours and minutes (depending on your radio model) whenever the ignition switch is in the “ON” or “ACC” position. When the ignition switch is in the “OFF” position, or when the radio frequency is being displayed, time keeping is accurately maintained.
INSTRUMENT PANEL AND CONTROLS SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL HANDS FREE PHONE CAPABILITY 161 Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
INSTRUMENT PANEL AND CONTROLS Mode Button (Radio Mode) Press the mode button repeatedly to select between the CD player or Satellite Radio (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down.The radio will remained tuned to the new station until you make another selection.
INSTRUMENT PANEL AND CONTROLS RW/FF (Radio Mode) Pressing the rewind/fast forward button causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM, FM or Satellite (if equipped) frequencies. TUNE Control (Radio Mode) Turn the right side rotary control to increase or decrease the frequency. AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control and BASS will display.
INSTRUMENT PANEL AND CONTROLS Select the button (1-6) you wish to lock onto this station and press and release that button. If a button is not selected within 5 seconds after pressing the SET button, the station will continue to play but will not be stored into push-button memory. You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window.
INSTRUMENT PANEL AND CONTROLS 165 NOTE: • You may insert or eject a disc with the radio or ignition switch OFF. SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. • If you insert a disc with the ignition ON and the radio OFF, the CD will automatically be pulled into the CD Player and the display will show the time of day.
INSTRUMENT PANEL AND CONTROLS Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, AND VIDEO CAPABILITIES Press the SEEK button to move to the next randomly selected track. Press and hold the FF button to fast forward through the tracks.
INSTRUMENT PANEL AND CONTROLS Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it. When the audio system is turned on, the sound will be set at the same volume level as last played.
INSTRUMENT PANEL AND CONTROLS SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. Pressing the AM/FM button continues the search in the alternate frequency band. To stop the search, press SCAN a second time. INFO Button (Radio Mode) Press the INFO button for an RBDS station (one with call letters displayed).
INSTRUMENT PANEL AND CONTROLS Press the rotary TUNE control a fourth time and BAL will display. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers. Press the rotary TUNE control a fifth time and FADE will display. Turn the TUNE control to the right or left to adjust the sound level between the front and rear speakers. Press the rotary TUNE control again to exit setting tone, balance and fade.
INSTRUMENT PANEL AND CONTROLS Program Type Jazz Classical Rhythm and Blues Soft Rhythm and Blues Foreign Language Religious Music Religious Talk Personality Public College Unassigned Weather 16 Digit-Character Display Jazz Classical Rhythm_and_Blues Soft_R_&_B Foreign_Language Religious_Music Religious_Talk Personality Public College Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name.
INSTRUMENT PANEL AND CONTROLS Inserting Compact Disc(s) CAUTION! This CD player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day. If you insert a disc with the ignition OFF, the display will show the time of day for about 5 seconds, then go out.
INSTRUMENT PANEL AND CONTROLS SCAN Button (CD MODE For CD Audio Play) Press the Scan button to scan through each track on the CD currently playing. LOAD/EJECT Button (CD Mode For CD Audio Play) LOAD/ EJECT - Load Press the LOAD/ EJECT button and the pushbutton with the corresponding number where the CD is being loaded. The radio will display PLEASE WAIT and prompt when to INSERT DISC. After the radio displays ⬙LOAD DISC⬙ insert the CD into the player.
INSTRUMENT PANEL AND CONTROLS TIME Button (CD MODE For CD Audio Play) Press this button to change the display from a large CD playing time display and small clock time display to a large clock time display and small CD playing time display. RW/FF (CD MODE For CD Audio Play) Press FF (Fast Forward) once and the CD player will begin to fast forward until FF is pressed again or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner.
INSTRUMENT PANEL AND CONTROLS Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions. Supported media (disc types) The MP3 file recording media supported by the radio are CD-ROM, CD-R and CD-RW. Supported medium formats (file systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension.
INSTRUMENT PANEL AND CONTROLS Supported MP3 file formats The radio will recognize only files with the *.mp3 extension as MP3 files. Non-MP3 files named with the *.mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
INSTRUMENT PANEL AND CONTROLS Playback of MP3 files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
INSTRUMENT PANEL AND CONTROLS LOAD / EJECT - Eject Press the LOAD/ EJECT button and the pushbutton with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. Press and hold the LOAD/ EJECT button to eject all discs in the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded.
INSTRUMENT PANEL AND CONTROLS AM/FM Button (CD Mode For MP3 Play) Switches back to Radio mode. RND/ PTY Button (CD Mode For MP3 Play) Pressing this button plays files randomly. SET/DIR Button (CD Mode For MP3 Play) Press the SET/DIR Button to display folders, when playing an MP3 discs that have a file/folder structure. Turn the TUNE control to display available folders or move through available folders. Press the TUNE control to select a folder.
INSTRUMENT PANEL AND CONTROLS System Activation To activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com. Please have the following information available when activating your system: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID). 2. Credit card information. 3. Your Vehicle Identification Number.
INSTRUMENT PANEL AND CONTROLS mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. Selecting Satellite Mode in REF Radios Press the MODE button repeatedly until ⬙S A⬙ appears in the display. A CD may remain in the radio while in the Satellite radio mode. Selecting Satellite Mode in RAQ Radios Press the MODE button repeatedly until the word ⬙SIRIUS⬙ appears in the display.
INSTRUMENT PANEL AND CONTROLS Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory. These satellite channel pre-set stations will not erase any AM or FM pre-set memory stations. Follow the memory pre-set procedures that apply to your radio. Using the PTY (Program Type) Button (if equipped) Follow the PTY button instructions that apply to your radio.
INSTRUMENT PANEL AND CONTROLS Reception Quality Satellite reception may be interrupted due to one of the following reasons. • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception. • Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage.
INSTRUMENT PANEL AND CONTROLS 183 The left hand control is a rocker type switch with a push button in the center. The function of the left hand control is different depending on which mode you are in. will go to the beginning of the current track or to the beginning of the previous track if it is within one second after the current track begins to play. The following describes the left hand control operation in each mode.
INSTRUMENT PANEL AND CONTROLS 3. Do not apply paper or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. NOTE: If you experience difficulty in playing a particular disc, it may be damaged (i.e.
INSTRUMENT PANEL AND CONTROLS Air Conditioning And Heater 185 in the snowflake button shows that the air conditioning is on. Press the button a second time to turn the air conditioning off. Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy.
INSTRUMENT PANEL AND CONTROLS Recirculation Modes (Panel or Bi-Level) Select the recirculation modes when the outside air contains dust, odors, high humidity, or if rapid cooling is desired. This feature allows for recirculation of interior air only. Air flows through the panel outlets in this mode. Panel (Fresh Air Modes) Outside air flows through the outlets located in the instrument panel. Bi-Level Outside air flows through the outlets located in the instrument panel and at the floor.
INSTRUMENT PANEL AND CONTROLS Temperature Control The rotary knob at the center of the control panel controls the temperature of the interior air. You can choose your degree of comfort by rotating the knob. The coldest temperature setting is to the extreme left (blue region) and the warmest setting is to the extreme right (red region) of the rotation. Circulation The cab is designed with features to promote outside air circulation. There are grilles in the cab back panel.
INSTRUMENT PANEL AND CONTROLS Operating Tips Fast Cooldown For a fast cooldown, turn the blower fan rotary knob to the extreme right position, turn the mode control to the panel fresh position, press the snowflake button to turn on the air conditioning, and drive with the windows open for the first few minutes. Once the hot air has been expelled, close the windows and turn the mode selector to the Recirculation Panel Mode or Recirculation Mode Bi-level position.
INSTRUMENT PANEL AND CONTROLS Summer Operation Air conditioned vehicles must be protected with a high quality antifreeze coolant during summer to provide proper corrosion protection and to raise the boiling point of the coolant for protection against overheating. A 50% concentration of engine coolant to distilled water is recommended. See coolant section of Owner’s manual.
INSTRUMENT PANEL AND CONTROLS Operation Tips Chart
INSTRUMENT PANEL AND CONTROLS 191 REAR WINDOW DEFROSTER – IF EQUIPPED CAUTION! Use care when washing the inside of the rear window to prevent damage to heating elements. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Also, keep all objects a safe distance from the window to prevent damaging the heating elements.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . . 196 ▫ Manual Transmission . . . . . . . . . . . . . . . . . . 196 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 196 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 197 ▫ Engine Block Heater — If Equipped . . . . . . . . 198 䡵 Automatic Transmission . . . . . . . . . . . . . . . . . . 199 ▫ NV 233 Transfer Case Operating Information/Precautions . . . . . . . . . . . . . . . .
STARTING AND OPERATING 䡵 Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . 221 ▫ Radial-Ply Tires . . . . . . . . . . . . . . . . . . . . . . 236 ▫ Rear Wheel Anti-Lock Brake System — (If Equipped) . . . . . . . . . . . . . . . . 221 ▫ Compact Spare Tire — If Equipped . . . . . . . . . 237 ▫ Four-Wheel Anti-Lock Brake System — If Equipped . . . . . . . . . . . . . . . . . . 222 䡵 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 223 䡵 Rocking The Vehicle . . . . . . . .
STARTING AND OPERATING 195 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . . 246 ▫ Gross Combined Vehicle Weight Rating (GCWR) . 259 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . . 246 ▫ Trailer Towing—Hitches . . . . . . . . . . . . . . . . 259 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . . 247 ▫ Trailer Towing Information (Maximum Trailer Weight Ratings) . . . . . . . . . 260 ▫ Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 247 ▫ Fuel System Cautions . .
STARTING AND OPERATING STARTING PROCEDURES The starter should not be operated for more than 15 second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. Manual Transmission Apply the parking brake, place the gearshift control lever in NEUTRAL and depress clutch pedal to the floor before starting the vehicle. This vehicle is equipped with a clutch interlocking ignition system. It will not start unless the clutch is depressed.
STARTING AND OPERATING Normal Starting Normal starting of either a warm or cold engine is obtained without pumping or depressing the accelerator pedal. Turn the key to the START position and release when the engine starts. If the engine fails to start within 10 seconds, turn the key to the OFF position, wait 5 seconds, then repeat the starting procedure. If Engine Fails To Start If the engine fails to start after you have followed the Normal Starting procedure, it may be flooded.
STARTING AND OPERATING WARNING! WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. After Starting The idle speed is automatically controlled on fuel injected engines and will decrease as the engine warms up.
STARTING AND OPERATING WARNING! Remember to disconnect the cord before driving. Damage to the 110-115 volt electrical cord could cause electrocution. AUTOMATIC TRANSMISSION Automatic Transmission The electronic PRNDL on the instrument cluster indicates the transmission gear selected. The selector lever is mounted on the right side of the steering column. To drive, move the selector lever from Park or Neutral to the desired drive position.
STARTING AND OPERATING WARNING! WARNING! Your vehicle could move and injure you and others if it is not completely in P (Park). Check by trying to move the gearshift lever back and forth without first pulling the lever toward you, after you have set it in P (Park). Make sure it is in Park before leaving the vehicle. It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed.
STARTING AND OPERATING 201 “N” Neutral Shift to Neutral when vehicle is standing for prolonged periods with engine running. Engine may be started in this range. Set the parking brake if you must leave the vehicle. “1” First For driving up very steep hills and for engine braking at low speeds 25 mph (40 km/h) or less when going down hill. To prevent excessive engine speed do not exceed 25 mph (40 km/h) in this range. “D” Drive For most city and highway driving.
STARTING AND OPERATING • transmission has reached normal operating temperature. NOTE: If the vehicle is started in extremely cold temperatures, the transmission may not shift into Overdrive and will automatically select the most desirable gear for operation at this temperature. Normal operation will resume when the transmission fluid temperature has risen to a suitable level. Refer also to the Note under torque converter clutch, later in this section.
STARTING AND OPERATING performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in “TOW/HAUL” mode, 5th gear (if equipped) is disabled and 2-3 and 3-4 shift patterns are modified. Shifts into Overdrive (4th gear) are allowed during steady cruise (for improved fuel economy) and automatic closed-throttle downshifts to 3rd gear (for improved braking) will occur during steady braking.
STARTING AND OPERATING transmission into gear may seem sluggish. This is due to the fluid partially draining from the torque converter into the transmission. This condition is normal and will not cause damage to the transmission. The torque converter will refill within five seconds of shifting from Park into any other gear position. Manual Transmission — 6-Speed NOTE: The parking brake should be engaged before leaving the vehicle, especially on an incline.
STARTING AND OPERATING Never drive with your foot resting on the clutch pedal, or attempt to hold the vehicle on a hill with the clutch pedal partially engaged, as this will cause abnormal wear on the clutch. Recommended Shift Speeds To use your manual transmission for fuel economy it should be upshifted as listed below. Shift at the vehicle speeds listed for acceleration.
STARTING AND OPERATING Downshifting Moving from a high gear down to a lower gear is recommended to preserve brakes when driving down steep hills. In addition, downshifting at the right time provides better acceleration when you desire to resume speed. For acceleration at speeds less than 20 mph (30 km/h), 2nd gear is recommended.
STARTING AND OPERATING 207 position - see Shifting Procedure section for specific shifting instructions. The 4HI and 4LO positions are designed for loose, slippery road surfaces only. Driving in the 4HI and 4LO positions on dry hard surfaced roads may cause increased tire wear and damage to the driveline components. flashing the transfer case position is two-wheel drive (2WD). If the indicator light is on the desired position (4HI or 4LO) has been obtained.
STARTING AND OPERATING or illuminates during driving, it means that the 4WD system is not functioning properly and that service is required. When operating your vehicle in 4LO, the engine speed is approximately three times that of the 2WD or 4HI positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). WARNING! Proper operation of 4 wheel drive vehicles depends on tires of equal size, type and circumference on each wheel.
STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position. The parking brake should always be applied when the driver is not in the vehicle.
STARTING AND OPERATING Shifting Procedure - NV233 Transfer Case NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift.The indicator light for the previous position will remain ON and the newly selected position indicator light will continue to flash until all the requirements for the selected position have been met.
STARTING AND OPERATING ON. At this time, reduce speed and stop spinning the wheels to complete the shift. There may be a delay up to 10 seconds for the shift to complete after the wheels have stopped spinning. 4HI to 4LO or 4LO to 4HI NOTE: When shifting into or out of 4LO some gear noise may be heard. This noise is normal and is not detrimental to the vehicle or occupants. Shifting can be performed with the vehicle rolling 2-3 mph (3-5 km/h) or completely stopped.
STARTING AND OPERATING NOTE: If steps 1 or 2 of either the Preferred or Alternate Procedure are not satisfied prior to attempting the shift or if they no longer are being met while the shift attempt is in process then the indicator light will flash and the current transfer case position will be maintained. To retry the selection, turn the control knob back to the current position wait five (5) seconds, and retry shift.
STARTING AND OPERATING When additional traction is required, the 4HI and 4LO positions can be used to lock the front and rear driveshafts together through the transfer case inter-axle differential and force the front and rear wheels to rotate at the same speed. This is accomplished by rotating the 4WD Control Switch to these positions. The 4HI and 4LO positions are intended for loose, slippery road surfaces only.
STARTING AND OPERATING The SERVICE 4WD warning light monitors the electric shift 4WD system. If this light remains on after engine start up or illuminates during driving, it means that the 4WD system is not functioning properly and that service is required. shift to take place. Shifting while only the front or rear wheels are spinning can cause damage to the transfer case.
STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position. The parking brake should always be applied when the driver is not in the vehicle.
STARTING AND OPERATING Shifting Procedure - NV244 Transfer Case NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift.The indicator light for the previous position will remain ON and the newly selected position indicator light will continue to flash until all the requirements for the selected position have been met.
STARTING AND OPERATING spinning the wheels to complete the shift. There may be a delay up to 10 seconds for the shift to complete after the wheels have stopped spinning. NOTE: Delayed shifting out of the 4HI position may be experienced due to uneven tire wear, low tire pressure, or excessive loading. 4HI to 4LO or 4LO to 4HI NOTE: When shifting into or out of 4LO some gear noise may be heard. This noise is normal and is not detrimental to the vehicle or occupants.
STARTING AND OPERATING 4. After the desired position indicator light is ON (not flashing), shift transmission back into gear (release clutch on manual transmissions).
STARTING AND OPERATING 219 Care should be taken to avoid sudden accelerations when both rear wheels are on a slippery surface. This could cause both rear wheels to spin, and allow the vehicle to slide sideways on the crowned surface of a road or in a turn. PARKING BRAKE The foot operated parking brake is positioned below the lower left corner of the instrument panel. To release the parking brake, pull the parking brake release handle.
STARTING AND OPERATING NOTE: The instrument cluster brake warning light indicates only that the parking brake is applied. You must be sure the parking brake is fully applied before leaving the vehicle. When parking on a hill, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should be applied whenever the driver is not in the vehicle.
STARTING AND OPERATING BRAKE SYSTEM In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be significantly increased over that required with the power system operating. If either the front or rear hydraulic system loses normal capability, the remaining system will still function with some loss of braking effectiveness.
STARTING AND OPERATING Four-Wheel Anti-Lock Brake System — If Equipped This Anti-Lock Brake System is designed to aid the driver in maintaining vehicle control under adverse braking conditions. The system operates with a separate computer to modulate hydraulic pressure to prevent wheel lock-up and help avoid skidding on slippery surfaces. The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure. The pump motor makes a low humming noise during operation, which is normal.
STARTING AND OPERATING WARNING! • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING ROCKING THE VEHICLE If vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between FIRST and REVERSE, while applying slight pressure to the accelerator. TIRE SAFETY INFORMATION Tire Markings The least amount of accelerator pedal pressure to maintain the rocking motion without spinning the wheels or racing the engine is most effective.
STARTING AND OPERATING 225 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • Temporary Spare tires are high pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING 227 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (ie. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING 229 Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure for passenger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar. For vehicles other than passenger cars, the cold tire inflation pressures are listed on either the shutface of the driver’s door, the “B” pillar, the Certification Label or in the Tire Inflation Pressures brochure in the glove compartment.
STARTING AND OPERATING Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
STARTING AND OPERATING combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX pounds” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3.
STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. 233 1. Safety— WARNING! Improperly inflated tires are dangerous and can cause accidents. • Under inflation increases tire flexing and can result in tire failure. • Over inflation reduces a tire’s ability to cushion TIRES—GENERAL INFORMATION shock.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. maximum loaded vehicle condition. These pressure conditions will be found in the “Supplemental Tire Pressure Information” section of this manual. 3.
STARTING AND OPERATING 235 check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. CAUTION! Tire pressures change by approximately 1 psi (7 kPa) per 12° F (7° C) of air temperature change.
STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high speed vehicle operation.
STARTING AND OPERATING 237 Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and reinstalled at the first opportunity. Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare.
STARTING AND OPERATING Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tire warning label located on the limited use spare tire and wheel assembly. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not. Installation of this limited use spare tire affects vehicle handling.
STARTING AND OPERATING 239 WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed. Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced.
STARTING AND OPERATING Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manufacturer strongly recommends that you use tires equivalent to the originals in size, quality and performance when replacement is needed (see the paragraph on tread wear indicators). Refer to the Tire and Loading Information placard for the size designation of your tire.
STARTING AND OPERATING CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. Alignment And Balance Poor suspension alignment may result in: • Fast tire wear. • Uneven tire wear, such as feathering and one-sided wear. • Vehicle pull to right or left. Tires may also cause the vehicle to pull to the left or right. Alignment will not correct this condition. See your dealer for proper diagnosis.
STARTING AND OPERATING TIRE CHAINS Use “Class S” chains only on the rear tires on Dakota trucks, or other traction aids that meet SAE Type “S” specifications. NOTE: Chains must be the proper size for the vehicle, as recommended by the chain manufacturer. CAUTION! To avoid damage to your vehicle, tires or chains, observe the following precautions: • Because of limited chain clearance between tires and other suspension components, it is important that only chains in good condition are used.
STARTING AND OPERATING These cautions apply to all chain traction devices, including link and cable (radial) chains. Tire chain use is permitted only on the rear tires of Dakota trucks. NOTE: The use of class “S” chains is permitted on Dakotas with P245/70R16 tires. CAUTION! Do not use tire chains on 4x4 Dakota trucks equipped with P265/65R17 tires. There may not be adequate clearance for the chains and you are risking structural or body damage to your vehicle.
STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates and tend to develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all season type tires.
STARTING AND OPERATING FUEL REQUIREMENTS All engines are designed to meet all emissions regulations and provide excellent fuel economy and performance when using high quality unleaded “regular” gasoline having an octane rating of 87. The 3.7L/4.7L routine use of premium gasoline is not Engines recommended. Under normal conditions the use of premium fuel will not provide a benefit over high quality regular gasolines and in some circumstances may result in poorer performance. 4.7L HO Engines The 4.
STARTING AND OPERATING Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasolines contain oxygenates, and are specifically blended to reduce vehicle emissions and improve air quality. We strongly support the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability for the engine and fuel system components.
STARTING AND OPERATING It is even more important to look for gasolines without MMT in Canada because MMT can be used at levels higher than allowed in the United States. MMT is prohibited in Federal and California reformulated gasolines. 247 ADDING FUEL Materials Added To Fuel All gasolines sold in the United States are required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in unnecessary cost.
STARTING AND OPERATING CAUTION! WARNING! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. A fire may result if gasoline is pumped into a portable container that is inside of a vehicle or on a truck bed. You could be burned. Always place gas containers on the ground while filling. NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full. NOTE: Tighten the gas cap until you hear a “clicking” sound.
STARTING AND OPERATING CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. WARNING! • Never allow any lit smoking materials near the vehicles while removing the cap or filling the tank. • Never add fuel to the vehicle when the engine is running.
STARTING AND OPERATING • When pulling a heavy load or driving a fully loaded vehicle when the humidity is low and the temperature is high, use a premium unleaded fuel to help prevent spark knock. If spark knock persists, lighten the load, or engine piston damage may result. • The use of fuel additives which are now being sold as octane enhancers is not recommended. Many of these products contain high concentrations of methanol.
STARTING AND OPERATING • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. CATALYTIC CONVERTER The catalytic converter requires the use of unleaded fuel only.
STARTING AND OPERATING A scorching odor may be detected if you continue to run a malfunctioning engine. The odor may indicate severe and abnormal catalyst overheating. If this occurs, the vehicle should be stopped, the engine shut off and the vehicle allowed to cool. Service, including a tune-up to manufacturer’s specifications should be obtained immediately.
STARTING AND OPERATING Rating (GAWR) front and rear, and Vehicle Identification Number (VIN). A Month-Day-Hour (MDH) number is included on this label and shows the Month, Day, and Hour of manufacture. The bar code that appears on the bottom of the label is your Vehicle Identification Number (VIN). Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options, and cargo.
STARTING AND OPERATING Inflation Pressure (Cold) This is the cold tire inflation pressure for your vehicle for all loading conditions up to full GAWR. Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle. The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.
STARTING AND OPERATING WARNING! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle. A loaded vehicle is shown in the following example. Note that neither GVWR nor GAWR capabilities are exceeded. Overloading can cause potential safety hazards and shorten service life.
STARTING AND OPERATING TRAILER TOWING To maintain warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing. Definitions The following trailer towing related terminology definitions will assist in understanding the subsequent sections: GROSS COMBINATION WEIGHT RATING (GCWR) is the total permissible weight of your vehicle and trailer when weighed in combination. (Note that GCWR ratings include a 68 kg (150 lb.
STARTING AND OPERATING Consider the following items when computing the weight on the rear axle: • The tongue weight of the trailer. • The weight of any other type of cargo or equipment put in or on your vehicle. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle.
STARTING AND OPERATING • Do not interconnect the hydraulic brake system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. • Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs. (907 kg). • Use an approved trailer harness and connector. If a hitch is ordered, the proper wiring will be provided. • When hauling cargo or towing a trailer, do not overload your vehicle or trailer.
STARTING AND OPERATING Tongue Weight is the weight placed on the vehicle’s trailer hitch by the trailer. Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the GTW on the tow hitch of your vehicle.
STARTING AND OPERATING NOTE: When towing a trailer, the following requirements must be adhered to: Trailer Towing Information (Maximum Trailer Weight Ratings) • GCWR must not be exceeded ⴖTrailer Towing Guideⴖ • Total weight must be distributed between the tow vehicle and the trailer such that the following four (4) ratings are not exceeded: NOTE: For trailer towing information (maximum trailer weight ratings) refer to the following website address: http:// www.dodge.com/towing. 1. GVWR 2.
STARTING AND OPERATING If you regularly pull a trailer, regardless of the trailer size, stop and turn signals on the trailer are recommended for motoring safety. When the additional trailer lighting is connected to the vehicle, the flasher does not provide an indication of outside lamp/bulb failure. Therefore, an occasional visual check around the vehicle is recommended. Once the trailer is removed the above indication will return to the vehicle.
STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 7 - Pin Connector 4 - Pin Connector Cooling System Tips—Trailer Towing To reduce potential for engine and transmission overheating, take the following actions: • City Driving When stopped for short periods of time, put transmission in neutral and increase engine idle speed.
STARTING AND OPERATING • Highway Driving Reduce speed. • Air Conditioning Turn off temporarily. • See Cooling System Operating information in the Maintenance section of this manual for more information. To reduce potential for automatic transmission overheating, turn the “TOW/HAUL” feature on when driving in hilly areas or shift the transmission to Drive position 2 on more severe grades. Move the shift lever to the next lower position to eliminate excessive transmission shifting.
STARTING AND OPERATING CAUTION! Using this vehicle for snowplow applications can cause damage to the vehicle. WARNING! Attaching a snowplow to this vehicle could adversely affect performance of the airbag system in an accident. Do not expect that the airbag will perform as described earlier in this manual RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Recreational Towing 2WD Models Recreational towing of 2WD models is not allowable.
STARTING AND OPERATING Recreational Towing 4WD Models CAUTION! Internal damage to the transfer case will occur if a front or rear wheel lift is used when recreational towing. NOTE: Both the NV233 and NV244 HD transfer cases must be shifted into Neutral (N) for recreational towing. The Neutral (N) selection button is located on the lower left hand corner of the 4WD Control Switch. Shifts into and out of transfer case Neutral (N) can take place with the selector switch in any mode position.
STARTING AND OPERATING 6. Using the point of a ballpoint pen or similar object, depress the recessed transfer case Neutral (N) button for 4 seconds. 7. After shift is completed and the Neutral (N) light comes on release Neutral (N) button. 8. Start engine. 9. Shift automatic transmission into Reverse (R). 10. Release brake pedal for five seconds and ensure that there is no vehicle movement. 11. Repeat steps 9 and 10 with the transmission in Drive (D). 14. Attach vehicle to tow vehicle with tow bar.
STARTING AND OPERATING 267 CAUTION! 5. Shift automatic transmission to Neutral (N) or depress clutch on manual transmission. Damage to the transmission may occur if the transmission is shifted into Park (P) with the transfer case in Neutral (N) and the engine RUNNING. With the transfer case in Neutral (N) ensure that the engine is OFF prior to shifting the transmission into Park (P). 6.
STARTING AND OPERATING depressing the Neutral (N) button or are no longer met during the 1 second time, then all of the mode position indicator lights will flash continuously until all requirements are met or until the Neutral (N) button is released. NOTE: The ignition key must be ON for a shift to take place and for the position indicator lights to be operable. If the key is not ON, the shift will not take place and no position indicator lights will be on or flashing.
STARTING AND OPERATING CAUTION! • Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and damage internal parts. TRACTION When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 272 䡵 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 283 䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 273 䡵 Emergency Tow Hooks — If Equipped . . . . . . . . 286 䡵 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . 274 䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . . 287 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is on the top of the steering column, just behind the steering wheel. Press the flasher switch and all front and rear directional signals will flash intermittently. Press the switch a second time to turn off the emergency flashers. This is an emergency warning system and should not be used when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists.
WHAT TO DO IN EMERGENCIES ADDING FUEL If using a portable fuel container, it should have a flexible nozzle long enough to reach past the restriction in the fuel filler tube. WARNING! A fire may result if gasoline is pumped into a portable container that is in a vehicle or on a truck bed. You could be burned. Always place gas containers on the ground while filling. 273 WARNING! Remove the gas cap slowly to prevent fuel spray from the filler neck which may cause injury.
WHAT TO DO IN EMERGENCIES CHANGING A FLAT TIRE Jack Location In the Dakota, the scissor jack and tire changing tools for Club Cab models are stowed in a compartment under the rear passenger seat. Quad Cab model scissor jack and tire changing tools are accessed by lifting up the rear passenger seat. The jack is secured in place by turning the jack screw until the jack is secured into place. A finger operated helper tool is provided to assist removal and stowage of the jack.
WHAT TO DO IN EMERGENCIES 275 6 Jack Stowage Location Club Cab Jack Stowage Location Quad Cab
WHAT TO DO IN EMERGENCIES WARNING! The jack is designed as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes, unless suitable supports are placed under the vehicle as a safety measure. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Removing The Spare Tire Remove the spare tire before attempting to jack the truck. Attach the wheel wrench to the jack extension tube.
WHAT TO DO IN EMERGENCIES 277 • Rotate clockwise to stow the spare tire.
WHAT TO DO IN EMERGENCIES It is recommended that you stow the flat or spare to avoid tangling the loose cable. Tire Changing Procedure WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.
WHAT TO DO IN EMERGENCIES • Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. Preparations Park the vehicle on a firm level surface, avoiding ice or slippery areas. Set the parking brake and place the gear selector in PARK (automatic transmission). On Four Wheel Drive vehicles, shift the transfer case to the “4L” position.
WHAT TO DO IN EMERGENCIES 3. When changing a front wheel, place the jack under the frame rail behind the wheel. Locate the jack as far forward as possible on the straight part of the frame (prior to inboard transition. Operate the jack using the jack drive tube and the wheel wrench - the tube extension, may be used but is not required. When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube.
WHAT TO DO IN EMERGENCIES 281 WARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. Right Rear Jacking Location Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. 4.
WHAT TO DO IN EMERGENCIES 6. Using the wheel wrench, finish tightening the nuts in a crisscross pattern. Correct nut tightness is 85-115 ft. lbs. (115-155 N·m) torque. If in doubt about the correct tightness, have them checked with a torque wrench by your dealer or at a service station.
WHAT TO DO IN EMERGENCIES To Stow The Flat Or Spare Turn the wheel so that the valve stem is down. Slide the wheel retainer through the center of the wheel and position it properly across the wheel opening. For convenience in checking the spare tire inflation, stow with the valve stem toward the rear of the vehicle. Rotate the winch mechanism until the wheel is drawn into place against the underside of the vehicle. Continue to rotate until you feel the winch mechanism slip or click 3 times.
WHAT TO DO IN EMERGENCIES Check the Battery Test Indicator (if equipped). If a light or bright colored dot is visible in the indicator (if equipped), DO NOT jump-start the battery. If the indicator (if equipped) is dark or shows a green dot, proceed as follows: 1. Wear eye protection and remove all metal jewelry such as watch bands or bracelets which might make an unintended electrical contact. 2. Park the booster vehicle within cable reach but without letting the vehicles touch.
WHAT TO DO IN EMERGENCIES WARNING! Do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump starting because the battery could rupture or explode. The battery temperature must be brought up above freezing point before attempting jump start. 6.
WHAT TO DO IN EMERGENCIES EMERGENCY TOW HOOKS — IF EQUIPPED Your vehicle may be equipped with emergency tow hooks. WARNING! Chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. WARNING! Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury.
WHAT TO DO IN EMERGENCIES CAUTION! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. TOWING A DISABLED VEHICLE Proper towing or lifting equipment is required to prevent damage to your vehicle. Use of safety chains is recommended. Attach towing device to main structural members of the vehicle — not to bumpers or associated brackets.
WHAT TO DO IN EMERGENCIES NOTE: Towing the vehicle at more than 30 mph (50 km/h) or for more than 15 miles (25 km) can cause severe transmission damage.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment 3.7L V6 . . . . . . . . . . . . . . 292 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 298 䡵 Engine Compartment 4.7L/4.7HO V-8 . . . . . . . . 293 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . . 302 䡵 Onboard Diagnostic System — OBD II . . . . . . . . 294 ▫ Drive Belts — Check Condition And Tensioner . . . . . . . . . . . . . . . . . . . . . . . . . . . 302 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Air Conditioner Maintenance . . . . . . . . . . . . . 307 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 320 ▫ Power Steering — Fluid Check . . . . . . . . . . . . 308 ▫ Transfer Case . . . . . . . . . . . . . . . . . . . . . . . . 323 ▫ Front Suspension Ball Joints . . . . . . . . . . . . . . 309 ▫ Axles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323 ▫ Drive Shaft Constant Velocity Joints . . . . . . . .
MAINTAINING YOUR VEHICLE 291 ▫ Center High-Mounted Stoplamp And Cargo Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338 䡵 Recommended Fluids, Lubricants And Genuine Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344 ▫ License Lamps . . . . . . . . . . . . . . . . . . . . . . . 341 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344 ▫ Fog Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . 342 ▫ Chassis . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT 3.
MAINTAINING YOUR VEHICLE 293 ENGINE COMPARTMENT 4.7L/4.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE Loose Fuel Filler Cap Message After fuel is added, the vehicle diagnostic system can determine if the fuel filler cap is loose, improperly installed, or damaged. A loose fuel filler cap message will be displayed in the instrument cluster. Tighten the gas cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off.
MAINTAINING YOUR VEHICLE Your vehicle has a simple ignition key actuated test which you can use prior to going to the test station. To check if your vehicle’s OBD system is ready, you must do the following: 1. Insert your ignition key into the ignition switch. 2. Turn the ignition to the ON position, but do not crank or start the engine. 3. If you crank or start the engine, you will have to start this test over. 4.
MAINTAINING YOUR VEHICLE vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL symbol is on with the engine running. REPLACEMENT PARTS Use of genuine Mopar威 parts for normal/scheduled maintenance and repairs is highly recommended to insure the designed performance. Damage or failures caused by the use of non-Mopar威 parts for maintenance and repairs will not be covered by the manufacturer’s warranty.
MAINTAINING YOUR VEHICLE MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance. However, if a malfunction of these items does occur, it could adversely affect the engine or vehicle performance.
MAINTAINING YOUR VEHICLE 7. Add oil only if the level is below the “SAFE” range (at or below the “ADD” mark) on the engine oil level indicator (dipstick). Adding one quart of oil when the reading is at the ADD mark will result in a reading at the top of the SAFE zone on these engines. 299 CAUTION! Overfilling or underfilling the crankcase will cause oil aeration or loss of oil pressure. This could damage your engine.
MAINTAINING YOUR VEHICLE • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C). 4x4 Models, If Used Primarily For Off-Road Operation Every 50 hours of use. • Trailer towing, Taxi, Police or delivery service (commercial service). Dusty Conditions Driving through dust-laden air increases the problems of keeping abrasive materials out of the engine. Under these conditions, special attention should be given to the engine air cleaner.
MAINTAINING YOUR VEHICLE Engine Oil Identification (API) Symbol There is a symbol to aid you in selecting the proper engine oil. This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacture only recommends API Certified engine oils that meet the requirements of DaimlerChrysler Material Standard MS-6395. Use Mopar or an equivalent oil meeting the specification MS-6395.
MAINTAINING YOUR VEHICLE Materials Added to Engine Oils The manufacture strongly recommends against the addition of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental additives. Disposing of Used Engine Oil And Oil Filters Care should be taken in disposing of used engine oil and oil filters from your vehicle.
MAINTAINING YOUR VEHICLE Belts should be inspected for evidence of cuts, cracks, glazing, or frayed cords and replaced if there is indication of damage which could result in belt failure. Low generator belt tension can cause battery failure. Also check belt routing to make sure there is no interference between the belts and other engine components. Spark Plugs Spark plugs must fire properly to assure proper engine performance and emission control.
MAINTAINING YOUR VEHICLE WARNING! The air cleaner can provide a measure of protection in the case of engine backfire. Do not remove the air cleaner unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air cleaner removed. Failure to do so can result in serious personal injury.
MAINTAINING YOUR VEHICLE 305 CAUTION! WARNING! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle.
MAINTAINING YOUR VEHICLE To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start engine by pushing or towing the vehicle. • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idling or malfunctioning operating conditions.
MAINTAINING YOUR VEHICLE To determine the battery charge, check the battery test indicator (if equipped) on top of the battery. Refer to the illustration. CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case.
MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information book for further warranty information. • The air conditioning system contains refrigerant under high pressure.
MAINTAINING YOUR VEHICLE WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE also be given to hood latching components to insure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of a high quality lubricant such as Mopar威 Lock Cylinder Lubricant directly into the lock cylinder.
MAINTAINING YOUR VEHICLE WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. After the engine has warmed, operate the defroster for a few minutes to reduce the possibility of smearing or freezing the fluid on the cold windshield.
MAINTAINING YOUR VEHICLE WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, follow the preceding safety tips. Cooling System Inspection Coolant protection checks should be made at every 12 months (before the onset of freezing weather, where applicable).
MAINTAINING YOUR VEHICLE Cooling System Maintenance At the intervals shown in the Maintenance Schedules section of this manual, the system should be drained, flushed and refilled. See your authorized dealer for proper cooling system maintenance. Cooling System — Drain, Flush And Refill If the solution is dirty and contains a considerable amount of sediment, it should be cleaned and flushed. See your authorized dealer for proper draining, flushing and refilling of your vehicle’s cooling system.
MAINTAINING YOUR VEHICLE CAUTION! Mixing of coolants other than specified (nonHOAT), may result in engine damage and decreased corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible. Do not use plain water alone or alcohol base antifreeze products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator coolant and may plug the radiator.
MAINTAINING YOUR VEHICLE 315 WARNING! WARNING! Never add coolant to the radiator when the engine is overheated. Do not loosen or remove pressure cap to cool overheated engine. The coolant is under pressure and severe scalding could result. The warning words “DO NOT OPEN HOT” on the coolant pressure cap are a safety precaution. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap when the system is hot or under pressure.
MAINTAINING YOUR VEHICLE coolant. Your service attendant should be advised of this. When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember A. Do not overfill the coolant bottle. B. Check coolant freeze point in the radiator and in the coolant bottle. If antifreeze needs to be added, contents of coolant bottle also must be protected against freezing. C.
MAINTAINING YOUR VEHICLE attention should be given to examining hose surfaces nearest to high heat sources, such as the exhaust manifold. Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose clamps and couplings to make sure they are secure and no leaks are present. You are urged to use only the manufacturer’s specified hoses and clamps, or their equivalent in material and specification, in any fuel system servicing.
MAINTAINING YOUR VEHICLE Brake System Power Disc Brakes (Front) Disc brakes do not require adjustment; however, several hard stops during the break-in period are recommended to seat the linings and wear off any foreign material. Brake Master Cylinders The fluid level in the master cylinders should be checked whenever the vehicle is serviced, or immediately if the brake system warning light is on.
MAINTAINING YOUR VEHICLE CAUTION! Do not allow a petroleum-base fluid to contaminate the brake fluid. Seal damage may result. Brake Linings Your vehicle is equipped with self-adjusting brakes. During normal driving, a few brake applications while moving in reverse will maintain your brakes at the specified adjustment. Adjustment will continue until the brake linings are worn.
MAINTAINING YOUR VEHICLE Manual Transmission Fluid Level Check This fluid should be checked whenever other underhood services are performed. The fluid level is checked by removing the fill plug. If the level of the lubricant is more than 1/4⬙ (6.35 mm) below the bottom of the filler hole while the vehicle is level, enough lubricant should be added to bring the level to the bottom of the filler hole. This fluid does not require periodic changing.
MAINTAINING YOUR VEHICLE 6. Remove the dipstick again and note the fluid level on both sides. The fluid level should be between the “HOT” (upper) reference holes on the dipstick at normal operating temperature. Verify that solid coating of oil is seen on both sides of the dipstick. If the fluid is low, add as required into the dipstick tube. Do not overfill.
MAINTAINING YOUR VEHICLE Automatic Transmission Fluid And Filter Change To obtain best performance and long life for automatic transmissions, the manufacturer recommends that they be given regular maintenance service by an Authorized Dodge Dealer or Service Center. It is important that the transmission fluid be maintained at the correct level and that it be drained and refilled as specified. Follow the proper Maintenance Schedule for your type of driving.
MAINTAINING YOUR VEHICLE Transfer Case Inspect the transfer case for fluid leaks. If a fluid leak is evident the transfer case fluid level may be low. Have the transfer case serviced immediately. CAUTION! Damage may result from operation of the vehicle with low transfer case fluid. The transfer case fluid should be drained and refilled at the intervals specified. Lubricant Selection Refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE differential. Rear axle fluid level should be 1/4⬙ (6.35mm) below filler plug hole for 8 1/4⬙ axles and should be 5/8⬙ (16mm) below filler plug for 9 1/4⬙ axles. Front Axle Front Axle fluid level should be at the bottom of the fill plug. Selection of Lubricating Grease The National Lubricating Grease Institute (NLGI) has developed a symbol (Certification Mark) to aid the vehicle owner in the proper selection of grease for chassis components.
MAINTAINING YOUR VEHICLE Appearance Care and Protection from Corrosion The most common causes are: Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
MAINTAINING YOUR VEHICLE • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.
MAINTAINING YOUR VEHICLE • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use Mopar威 touch up paint on scratches as soon as possible. Your dealer has touch up paint to match the color of your vehicle. Interior Care Use Mopar威 Fabric Cleaner to clean fabric upholstery and carpeting.
MAINTAINING YOUR VEHICLE Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters or windshields equipped with a windshield wiper de-icer. Do not use scrapers or other sharp instruments which may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using.
MAINTAINING YOUR VEHICLE 329 contain “Mini”fuses and plug-in “ISO” relays. A label inside the latching cover of the Power Distribution Centers identifies each component for ease of replacement, if necessary. These fuses and relays can be obtained from your dealer. Center (PDC) located in the engine compartment. The I.O.D. cavities include a snap-in retainer that allows the fuse to be disconnected, without removing it from the fuse block. Pressing the I.O.D. fuse back into the cavity reconnects it.
MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Dome Light . . . . . . . . . . . Cargo Light . . . . . . . . . . . Overhead Console Lights . . Reading Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BULB REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bulb No. WL212–2 . . . . 567 . . . . 192 WL212–2 LIGHT BULBS — Outside Bulb No. Headlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE Removing Headlamp Assembly 331 Removing Headlamp Assembly 1. Open the hood. 2. Remove the 3 screws attaching the headlamp housing to the inner panel. 3. Grasp the headlamp and pull firmly to disengage the headlamp housing from the fender panel.
MAINTAINING YOUR VEHICLE 4. While firmly holding the headlamp housing in your hands unlock and disconnect Headlamp bulb connector. 5. Twist 1/4 turn and remove Headlamp bulb from housing and replace. Unlocking Connector 6. Twist 1/4 turn and remove bulb and socket from housing, pull bulb straight out from socket and replace.
MAINTAINING YOUR VEHICLE Removing Headlamp from Assembly Removing Headlamp Bulb 333 7
MAINTAINING YOUR VEHICLE Front Park and Turn Signal Lamp. • Open the hood. • Remove the (3) screws attaching the headlamp housing to the inner panel. • Grasp the headlamp and pull firmly to disengage the headlamp housing from the fender panel. NOTE: It is not necessary to disconnect the connector to replace this bulb. If the bulb socket needs replacement disconnect the connector. Disconnecting Headlamp Bulb Connector 7. Reverse procedure to install new Headlamp bulb into the headlamp assembly.
MAINTAINING YOUR VEHICLE Removing Turn Signal Bulb • Rotate bulb socket 1/4 turn and remove socket from housing. • Pull bulb straight from socket. • Reverse procedure to install new turn signal bulb.
MAINTAINING YOUR VEHICLE Rear Side Marker, Taillamps/Stoplamp, and Turn Signal Bulbs — Replacement 1. Remove the two (2) screws that pass through the bed sheetmetal. Pulling Housing From Body 2. Pull the taillamp housing straight out from the body.
MAINTAINING YOUR VEHICLE 3. Rotate the bulb socket from the housing. Rotating Bulb Socket From Housing 337 4. Pull bulb straight out of socket.
MAINTAINING YOUR VEHICLE 5. Reverse Procedure to install bulb and housing. Place the two raised blocks passed the body. Center High-Mounted Stoplamp And Cargo Lamp 1. Remove the two (2) screws holding the housing/lens to the body as shown.
MAINTAINING YOUR VEHICLE 2. Remove housing from Cab. 339 3. Remove connector from housing tab for more clearance.
MAINTAINING YOUR VEHICLE 4. Turn desired bulb socket 1⁄4 turn and remove socket and bulb from housing. Pulling Bulb From Socket • Outside Bulbs: Cargo Lamps Removing Socket From Housing 5. Pull desired bulb straight from the socket. • Inside Bulb: Center High Mount Stop Lamp 6. Reverse procedure for installation of bulbs and housing.
MAINTAINING YOUR VEHICLE License Lamps 341 2. Rotate the socket 1/4 turn counterclockwise. 1. Using a screw driver pry black rubber housing from the bumper.
MAINTAINING YOUR VEHICLE 3. Pull bulb from socket. Fog Lamps 1. Disconnect connector from fog lamp by raising wire harness lock tab and pulling on wire harness connector. 2. Rotate fog lamp bulb 1/4 turn counterclockwise and pull to remove from fog lamp housing. 3. Reverse Procedure to install. Pulling Bulb From Socket 4. Reverse procedure for installation.
MAINTAINING YOUR VEHICLE 343 FLUIDS AND CAPACITIES U.S. Metric 22 Gal. 22 Gal 83L 83L 5 Qt. 6 Qt. 6 Qt. 4.7L 5.7L 5.7L 13.3 Qt. 13.3 Qt. 13.3 Qt. 12.5L 12.5L 12.5L Fuel 3.7L/4.7L, 87 Octane 4.7L HO, 91 Octane, Recommended Not Required Engine Oil (with filter) 3.7L, SAE 5W-30, API Certified 4.7L, SAE 5W-30, API Certified 4.7L HO, SAE 5W-30, API Certified Cooling System (includes 2.1 Qts./2L for coolant bottle 3.7L (Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) 4.
MAINTAINING YOUR VEHICLE RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection 3.7L/4.7L Fuel Selection 4.7L HO Fluids, Lubricants and Genuine Parts Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) P/N 5011764AB or equivalent. Use SAE 5W-30, API Certified, meeting material standard MS-6395. Mopar威 Engine Oil Filter, P/N 5281090 or equivalent.
MAINTAINING YOUR VEHICLE 345 Chassis Component Automatic Transmission Manual Transmission (Getrag 238) Transfer Case Front Axle Rear Axle Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar威 ATF+4, Automatic Transmission Fluid. Mopar威 ATF+4, Automatic Transmission Fluid. Mopar威 ATF+4, Automatic Transmission Fluid. SAE 75W-90 Multipurpose Type, GL-5 Gear Lubricant (MS9763). SAE 75W-140 Synthetic Gear Lubricant (MS-8985).
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . . . 348 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 352 䡵 Emissions Testing . . . . . . . . . . . . . . . . . . . . . . . 348 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . . 362 C 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 348 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type on the following pages must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and S reliability.
MAINTENANCE SCHEDULES MAINTENANCE SCHEDULES There are two maintenance schedules that show the required service for your vehicle. First is Schedule “B”. It is for vehicles that are operated under the conditions that are listed below and at the beginning of the schedule. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km).
M A I N T E N A N C E S C H E D U L E S 8 350 MAINTENANCE SCHEDULES Use the schedule that best describes your driving conditions. Where time and mileage are listed, follow the interval that occurs first. • Check the windshield washer solvent and add if required. NOTE: Under no circumstances should oil change intervals exceed 6000 miles (10 000 km) or 6 months whichever comes first. • Check tire pressure and look for unusual wear or damage.
MAINTENANCE SCHEDULES • Inspect the CV joints (if equipped) and front suspension components. • Check the automatic transmission fluid level (if equipped). 351 M A • Check the manual transission fluid level (if equipped). I • Check the coolant level, hoses, and clamps.
M A I N T E N A N C E S C H E D U L E S 8 352 SCHEDULE “B” Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90° F (32° C). • Trailer towing.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Inspect engine air cleaner filter, replace if necessary.
M 354 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 A months whichever comes first. N C Rotate tires. E Change rear axle fluid. S C H E D U L E S 8 Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary.
M 356 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 months whichA ever comes first. N Rotate tires. C E Change rear axle fluid. S C H E D U L E S 8 Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace if required. Drain and refill automatic transmission fluid, change filter (3.7L).
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Inspect auto tension drive belt and replace if required.
M 358 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 A months whichever comes first. N C Rotate tires. E Change rear axle fluid. S C H E D U L E S 8 Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace if required.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Flush and replace engine coolant, if not done at 60 months. Change rear axle fluid. Change front axle fluid (4X4).
M 360 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 A months whichever comes first. N C Rotate tires. E Change rear axle fluid. S C H E D U L E S 8 Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace if required. Drain and refill transfer case fluid (4X4).
SCHEDULE “B” Miles (Kilometers) Drain and refill automatic transmission fluid and change main sump filter and spin-on cooler return filter if equipped. (4.7L). Flush and replace engine coolant, if not replaced at 102,000 miles (163 000 km). 105,000 (168 000) This applies only if your vehicle is used for police, taxi, fleet, or frequent trailer towing. Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts.
M 362 SCHEDULE “A” A I Schedule “A” N T Miles E N (Kilometers) A [Months] N C Change engine oil and engine oil filter. E Rotate tires. S C H E D U L E S 8 Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace as necessary. Replace spark plugs.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check transfer case fluid level (4X4). Flush and replace engine coolant at 60 months, if not replaced at 102,000 miles (163 000 km). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace if required.
M 364 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Check transfer case fluid level (4X4). S C H E D U L E S 8 Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace if required.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Drain and refill tranfer case fluid (4X4). Flush and replace engine coolant, if not done at 60 months. Flush and replace engine coolant, if not done at 102,000 miles (163 000 km) Inspect brake linings. Inspect engine air cleaner filter, replace as necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.
M 366 SCHEDULE “A” A I WARNING! N T E You can be badly injured working on or around a N motor vehicle. Do only that service work for which A you have the knowledge and the right equipment. If N C you have any doubt about your ability to perform a E S C H E D U L E S 8 service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368 ▫ Prepare For The Appointment . . . . . . . . . . . . 368 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 368 ▫ Be Reasonable With Requests . . . . . . . . . . . . . 368 䡵 If You Need Assistance . . . . . . . . . . . . . . . . . . . 368 䡵 Warranty Information (U.S. Vehicles Only) . . . . . 370 䡵 Mopar威 Parts . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center.
IF YOU NEED CONSUMER ASSISTANCE Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY. Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unexpected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands behind only the manufacturer’s Service Contracts.
IF YOU NEED CONSUMER ASSISTANCE 371 9 U.S.
IF YOU NEED CONSUMER ASSISTANCE MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.
IF YOU NEED CONSUMER ASSISTANCE Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.
INDEX 10
INDEX Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . 247,273 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 303 Air Conditioner Maintenance . . . . . . . . . . . . . . . 307 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 185 Air Conditioning, Operating Tips . . . . . . . . . . 185,188 Air Conditioning Refrigerant . . . . . . . . . . . . . 307,308 Air Conditioning System . . . . . . . . . . . . . . . . 185,307 Air Filter . . . . . . . . . . . . . . . . . . . . . .
INDEX Ball Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306 Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283 Emergency Starting . . . . . . . . . . . . . . . . . . . . . 283 Gas Caution . . . . . . . . . . . . . . . . . . . . . . . . . . 283 Keyless Transmitter Replacement . . . . . . . . . . . . 26 Saving Feature (Protection) . . . . . . . . . . . . . . . 115 Belts, Drive . . . . . . . . . . .
INDEX Center High Mounted Stop Light . . . . . . . . . . . . 338 Center Seat Storage Compartment . . . . . . . . . . . . 142 Certification Label . . . . . . . . . . . . . . . . . . . . . . . 252 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . . 274 Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283 Chart, Tire Sizing . . . . . . . . . . . . . . . . . . . . . . . . 226 Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Customer Assistance . . . . . . . . . . . . . . . . . . . . . 368 Data Recorder, Event . . . . . . . . . . . . . . . . . . . . . . 57 Daytime Running Lights . . . . . . . . . . . . . . . . . . . 117 Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . . . 297 Defroster, Rear Window . . . . . . . . . . . . . . . . . . . 191 Defroster, Windshield . . . . . . . . . . . . . . . . . . . 74,186 Delay (Intermittent) Wipers . . . . . . . . . . . . . . . . . 120 Diagnostic System, Onboard . . . . .
INDEX Block Heater . . . . . . . . . . . . . . . . . . . . . . . . . 198 Break-In Recommendations . . . . . . . . . . . . . . . . 72 Compartment . . . . . . . . . . . . . . . . . . . . . . . . . 293 Coolant (Antifreeze) . . . . . . . . . . . . . . . . . 313,344 Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312 Exhaust Gas Caution . . . . . . . . . . . . . . . . . . 73,250 Fails to Start . . . . . . . . . . . . . . . . . . . . . . . . . . 197 Flooded, Starting . . . . . . . . . . .
INDEX Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . . 343 Fluid Level Checks Automatic Transmission . . . . . . . . . . . . . . . . . 320 Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318 Cooling System . . . . . . . . . . . . . . . . . . . . . . . 312 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 298 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 308 Transfer Case . . . . . . . . . . . . . . . . . . . . . . . . . 323 Fog Lights .
INDEX Gross Axle Weight Rating . . . . . . . . . . . . . . . . . . 253 Gross Cargo Weight . . . . . . . . . . . . . . . . . . . . . . 252 GVWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253,255 Hands-Free Phone . . . . . . . . . . . . . . . . . . . . . . . . 84 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . . 272 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330 High Beam . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Intermittent Wipers . . . . . . . . . . . . . . . . . . . . . . 120 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Jack Operation . . . . . . . . . . . . . . . . . . . . . . . 274,278 Jacking Instructions . . . . . . . . . . . . . . . . . . . . . . 279 Key, Replacement . . Key, Sentry . . . . . . . Key-In Reminder . . . Keyless Entry System Keys . . . . . . . . . . . Knee Bolster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Low Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 152,153 Malfunction Indicator . . . . . . . . . . . . . . . . . . . 157 Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . 153 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330 Turn Signal . . . . . . . . . . . . . . . . . . . . . . . . 118,336 Warning (Instrument Cluster Description) . . . . . 152 Washer Fluid . . . . . . . . . . . . .
INDEX Automatic Dimming . . . . . . . . . . . . . . . . . . . . . 82 Electric Powered . . . . . . . . . . . . . . . . . . . . . . . 83 Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Modifications/Alterations, Vehicle . . . . . . . . . . . . . 6 Mopar Parts . . . . . . . . . . . . . . . . . . . . . . . . . 297,372 Multi-Function Control Lever . .
INDEX Parking On Hill . . . . . . . . . . . . . . . . . . . . . . . . . 219 Passenger Airbag On/Off Switch . . . . . . . . . . . . . 55 Passing Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 Pets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Pets, Transporting . . . . . . . . . . . . . . . . . . . . . . . . 72 Phone, Cellular . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Phone, Hands-Free . . . . . . . . . . . . . . . . . . . . . . .
INDEX Reception, Radio . . . . . . . . . . . . . . . . . . . . . . . . 159 Reclining Front Seats . . . . . . . . . . . . . . . . . . . . . 108 Recommended Fluids, Lubricants and Genuine Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344 Recorder, Event Data . . . . . . . . . . . . . . . . . . . . . . 57 Recreational Towing . . . . . . . . . . . . . . . . . . . . . . 264 Shifting into Transfer Case Neutral (N) . . . . . . . 265 Shifting out of Transfer Case Neutral (N) . . . . .
INDEX Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 107 Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . 109 Reclining . .
INDEX Emergency (Jump Starting) . . . . . . . . . . . . . . . 283 Engine Block Heater . . . . . . . . . . . . . . . . . . . . 198 Steering Column Controls . . . . . . . . . . . . . . . . . . . . . . 118 Column Lock . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . 223,308 Wheel, Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 Steering Wheel Mounted Sound System Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Load Capacity . . . . . . . . . . . . . . . . . . . . . 229,230 Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 240 Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 224,233 Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 243 Spare Tire . . . .
INDEX Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 320 Manual . . . . . . . . . . . . . . . . . . . . . . . . 196,204,320 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 Transmitter Battery Service . . . . . . . . . . . . . . . . . . 26 Transmitter, Garage Door Opener . . . . . . . . . . . . 133 Transmitter Programming . . . . . . . . . . . . . . . . . . . 25 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . 239 Trip Computer . . . . . . . . . . . . . .
INDEX Windshield Fluid . . Windshield Windshield Washers . . . . . . . . . . . . . . . . 120,121,310 . . . . . . . . . . . . . . . . . . . . . . . . . . 120,310 Wiper Blades . . . . . . . . . . . . . . . . . . 310 Wipers . . . . . . . . . . . . . . . . . . . . . . . 120 Wiper Blade Replacement . . . . . . . . . . . . . . . . . . 310 Wipers, Intermittent . . . . . . . . . . . . . . . . . . . . . . 120 Wrecker Towing . . . . . . . . . . . . . . . . . . . . . . . . .