SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Van Conversions/Campers . . . . . . . . . . . . . . . . . 5 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 5 䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 6 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 5 䡵 Vehicle Modifications / Alterations . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 HOW TO USE THIS MANUAL Consult the table of contents to determine which section contains the information you desire. The detailed index, at the rear of this manual, contains a complete listing of all subjects. WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle.
INTRODUCTION VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is found on a stamped plate located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment. NOTE: It is illegal to remove the VIN plate.
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS 1 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . .11 ▫ To Unlock The Doors . . . . . . . . . . . . . . . . . . .18 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .11 ▫ To Lock The Doors . . . . . . . . . . . . . . . . . . . . .19 ▫ Sentry Key — If Equipped . . . . . . . . . . . . . . . .11 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .21 䡵 Ignition And Steering Lock — If Equipped . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .25 ▫ Seat Belts And Pregnant Women . . . . . . . . . . . .40 䡵 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . .40 ▫ Power Windows—If Equipped . . . . . . . . . . . . .26 ▫ Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbag . . . . . . . . . . . .40 ▫ Sliding Rear Window . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to order duplicate keys from your dealer or a locksmith. If you received your keys without the bag, ask your dealer to give you the number.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE loss of security protection. Additional Sentry Keys or Mobil Speed-pass™ devices held against or immediately adjacent to the ignition key when starting the engine may cause vehicle starting problems. If a problem occurs, remove the Sentry Key from the key-ring and attempt to start the vehicle again. Pagers, cell phones, walkman, etc. will have no effect on this system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Customer Key Programming You can program new keys to the system if you have two valid keys by doing the following: 1. Insert the first valid key into the ignition and turn the ignition to the ON position for at least 3 seconds but no longer than 15 seconds. Turn the ignition back to the OFF position and remove the first key. 2. Insert the second valid key and switch the ignition to the ON position within 15 seconds.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE IGNITION AND STEERING LOCK — IF EQUIPPED Manual Transmissions Depress and hold the release button located between the ignition switch and the instrument panel. Turn the ignition key to LOCK and remove the key. DOOR KEY The same key used to start the vehicle is also used to unlock the doors. To unlock the vehicle doors, insert the key into the lock and turn. To lock the doors, insert the key and turn.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 WARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death. NOTE: Vehicles equipped with remote keyless entry do not have a passenger side door lock cylinder.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Central Locking — If Equipped Vehicles with security will have a feature called ⬙Central Locking⬙. When the key is placed in the door cylinder and turned to the ⬙Unlock⬙ position, the security will be disarmed, the illuminated entry will be turned on and that door will be mechanically unlocked. If the key is once again turned to the unlock position within 5 seconds of the first unlock, the remaining doors will unlock.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 2. Fasten your seat belt (Fastening the seat belt will cancel any chiming that may confuse you during this programming procedure). REMOTE KEYLESS ENTRY — IF EQUIPPED 2 3. Place the key into the ignition. 4. Within 10 seconds cycle the key from the OFF position to the ON position four times; ending in the ON position ( Do not start the engine ). 5. Within 30 seconds, press the driver’s door lock switch in the LOCK direction. 6.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To unlock the doors: Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, the parking lights will flash on twice and if installed, the cargo lamp will turn on for 30 seconds. 5. Press and hold the UNLOCK button on a programmed (i.e. functional) key fob.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 To lock the doors: Press and release the LOCK button on the transmitter to lock all doors. If the ignition is OFF, when the doors are locked, the parking lights will flash on once and the horn will chirp once. The horn chirp feature will be shipped from the assembly plants activated. If desired this feature can be disabled by using the following procedure: 1. Enter your vehicle and close all doors. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Vehicles will be shipped from the assembly plants with the park lamp flash feature activated. If desired, this feature can be disabled by using the following procedure: 6. Continue to hold the LOCK button, wait at least 4 seconds, but no longer than 10 seconds, then press and hold the PANIC button. 1. Enter your vehicle and close all doors. 7. When a single chime is heard, release both buttons. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Using the Panic Alarm To activate the Panic mode while the ignition is OFF press and release the PANIC button on the transmitter once. When the Panic mode is activated, the interior lights will illuminate, the headlamps and parking lights will flash, and the horn will sound. To cancel the Panic mode press and release the PANIC button on the transmitter a second time.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Place the key into the ignition. 4. Turn the ignition to the ON position ( Do not start the engine ). 5. Press and hold the UNLOCK button on a programmed (i.e. functional) key fob. 6. Continue to hold the UNLOCK button, wait at least 4 seconds, but no longer than 10 seconds, then press and hold the PANIC button. 7. When a single chime is heard, release both buttons. The chime indicates that the system is in program mode. 8.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios. Transmitter Battery Service 1. This device may not cause harmful interference. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. 1. With transmitter buttons facing down, use a flat blade or dime to pry the two halves of the transmitter apart. Make sure not to damage the rubber gasket during removal. 2. Remove and replace the batteries. Be careful not to disturb the metal terminal near the batteries.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 To Set the Alarm: The alarm will set when you use the power door locks, turn the key in the driver’s door lock cylinder, or use the Keyless Entry transmitter to lock the doors. After all the doors are locked and closed the SECURITY light in the instrument cluster will flash rapidly to signal that the system is arming. The security light in the instrument panel cluster will flash rapidly for about 16 seconds to indicate that the alarm is being set.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE vehicle and lock the doors with the transmitter, the alarm will sound when you pull the door handle to exit. You may also accidentally disarm the system by unlocking the driver’s door with the door key and then locking it manually with the lock plunger. The door will be locked but the Security Alarm will not arm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 Auto Down (Driver’s Side Only) The driver’s window switch has an Auto Down feature. Press the window switch past the detent, release, and the window will go down automatically. Sliding Rear Window A locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window. The control on the left front door panel has up-down switches that give you fingertip control of all power windows.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger and, if so equipped, window bags for the driver and passengers seated next to a window.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 Lap/Shoulder Belts All seating positions except the Quad Cab front center seating position have combination lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt. 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The black buckle latch plate can be removed when the key is pressed into the buckle. Allow the retractor to take up the surplus webbing, and the buckles will hang vertically from the cab back exit bezel, thus freeing up all the area behind the front seats. 2. To reattach the seat belt to the front center seat, pull the black buckle latch plate forward from the cab back panel and insert it into the black keyed buckle until there is an audible click.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 2 Inserting Latch Plate In Use Position
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly. Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Press the button located on the upper belt guide, and then move it up or down to the position that serves you best.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Automatic Locking Mode (if Equipped) In this mode, the shoulder belt is automatically prelocked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is only available on the front passenger side belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too loose or too high is dangerous. • A belt worn too loose can allow you to slip down and under the belt in a collision. • A belt that is too loose or too high will apply crash forces to the abdomen, not to the stronger hip bones. In either case, the risk of internal injuries is greater. Wear a lap belt low and snug.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Enhanced Warning System (BeltAlert) will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts and Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug against the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 These airbags are certified to the new Federal regulations that allow less forceful deployments. WARNING! • Do not put anything on or around the airbag covers or attempt • • This vehicle may also be equipped with window bags to protect the driver and passengers in the first and second row sitting next to a window. If the vehicle is equipped with window bags, they are located above the side windows. Their covers are also labeled SRS AIRBAG.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbags inflate in moderate to high speed impacts. Along with the seatbelts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Window bags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 • The driver and front passenger seats should be moved back as far as practical to allow the airbag room to inflate. Airbag System Components The airbag system consists of the following: • Airbag Control Module WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Window Airbag System, on vehicles equipped, consists of the following: • AIRBAG Readiness Light (shared with the front airbag system) • Window Bags Above the Side Windows. • Airbag Control Module (shared with the front airbag system) • Side impact sensors • Interconnecting Wiring How The Airbag System Works • The airbag control module determines if a frontal collision is severe enough to require the airbags to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 WARNING! Ignoring the AIR BAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away. • When the airbag control module detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Passenger Airbag On/Off Switch – (Standard Cab Vehicles Only) The passenger front airbag is to be turned off only if the passenger: • is an infant (less than 1 year old) who must ride in the front seat because there is no rear seat, because the rear seat is too small for a rear-facing infant restraint or because the infant has a medical condition which makes it necessary for the driver to be able to see the infant, • is a child, age 1 to 12 who must ride in t
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 WARNING! To Turn On the Passenger Airbag (Standard Cab Vehicles Only) Whenever an airbag is turned off, even a lap/ shoulder belted passenger may hit their head, neck, or chest on the dashboard (instrument panel) or windshield in a crash. This may result in serious injury or death. Place the ignition key in the Passenger Airbag On/Off Switch, push the key in and turn counterclockwise, and remove the key from the switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Window Airbags Supplemental Restraint System (SRS)—If Equipped The window airbag control module determines if a side collision is severe enough to require the side airbags to inflate. The window airbag control module will not detect roll over, front or rear collisions. The airbag control module monitors the readiness of the electronic parts of the system whenever the ignition switch is in the ⬙START⬙ or ⬙RUN⬙ positions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag Systems WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or frame.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Child Restraint Everyone in your vehicle needs to be buckled up all the time — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years and under should ride properly buckled up in a rear seat, if available.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE of child restraints can be used rearward-facing: infant carriers and ⬙convertible⬙ child seats. Both types of child restraints are held in the vehicle by the lap/ shoulder belt. • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). ⬙Convertible⬙ child seats can be used either rearward-facing or forward-facing in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward facing child restraint should only be used in a rear seat, or in the front seat if the passenger’s front airbag is Off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 WARNING! Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Identification dots are located above the standard cab front seat lower anchorages as a guide for locating lower anchors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Installing the Child Restraint System WARNING! Do not install child restraint systems equipped with LATCH attachments in the center position of a Quad Cab model rear seat. The LATCH anchorages in this seat are designed for the two outboard seating positions only. A child may be placed in the rear center seating position of a Quad Cab model using the seat belt and child tether anchorage. Failure to follow this may result in serious or fatal injury.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. An incorrectly anchored tether strap could lead to seat failure and injury to the child.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 2. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal. Multiple Child Restraint Installation Sequence (Quad Cab Rear Seats) 3. Install the child restraint and remove the slack in the tether strap according to the manufacturer’s instructions. 1. Obtain tether straps by raising the head restraints and reaching between the rear glass and rear seat. The tether strap may be retained with an elastic band.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Place a child restraint on the center rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat and to the anchor directly behind the right seat. 6. Install each child restraint and remove the slack in the tether strap according to the child restraint manufacturer’s instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 2 Multiple Child Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 NOTE: A new engine will consume some oil during the first few thousand miles of operation. This should be considered as a normal part of the break-in and not interpreted as a sign of difficulty. SAFETY TIPS Transporting Passengers This vehicle is designed to carry passengers in the cab only. For safety reasons, NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! Exhaust gases contain carbon monoxide, a potentially toxic gas that by itself is colorless and odorless. To avoid inhaling these gases, the following precautions should be observed: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.) or if the front airbags have deployed. If there is any question regarding belt or retractor condition, replace the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Outside The Vehicle Door Latches Check for positive closing, latching and locking. Tires Examine tires for tread wear or uneven wear patterns. Check for stones, nails, glass or other objects lodged in the tread. Fluid Leaks Check area under vehicle after overnight parking for fuel, water, oil, or other fluid leaks. Also, if fuel fumes are detected the cause should be located and corrected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 ▫ Phone Call Features . . . . . . . . . . . . . . . . . . . .79 ▫ Automatic Dimming Mirror— If Equipped . . . .71 ▫ Advanced Phone Connectivity . . . . . . . . . . . . .82 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .71 ▫ UConnect™ System Features . . . . . . . . . . . . . .83 ▫ Exterior Mirrors Folding Feature . . . . . . . . . . .72 䡵 Seats . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 To Open And Close The Hood . . . . . . . . . . . . . .91 ▫ Passing Light . . . . . . . . . . . . . . . . . . . . . . . . .98 䡵 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93 ▫ High Beam / Low Beam Select Switch . . . . . . .98 ▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . . .93 ▫ Windshield Wipers . . . . . . . . . . . . . . . . . . . . .99 ▫ Battery Saver . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 ▫ To Accelerate For Passing . . . . . . . . . . . . . . . 105 ▫ Automatic Compass Calibration . . . . . . . . . . . 110 䡵 Overhead Console . . . . . . . . . . . . . . . . . . . . . . 106 ▫ Manual Compass Calibration . . . . . . . . . . . . . 111 ▫ Courtesy/Reading Lights . . . . . . . . . . . . . . . . 106 ▫ To Put Into a Calibration Mode . . . . . . . . . . . 111 䡵 Compass/Temperature Mini-Trip Computer . . . . 107 ▫ Outside Temperature . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Closing Sunroof - Express . . . . . . . . . . . . . . . 120 䡵 Cigar Lighter And Ash Receiver . . . . . . . . . . . . 123 ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . . . 120 䡵 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 ▫ Pinch Protect Override . . . . . . . . . . . . . . . . . 120 ▫ Front Cupholders . . . . . . . . . . . . . . . . . . . . . 124 ▫ Venting Sunroof - Express . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 MIRRORS Automatic Dimming Mirror— If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Electronic Power Mirrors — If Equipped Vehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side convex mirror. Some vehicles will not have a convex right side mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 Electric Rear Window Defroster and Heated Sideview Mirrors — If Equipped The Electric Rear Window Defroster and Heated side view mirrors are activated by pressing the heated grid button, located on the Climate Control panel, with the ignition On. Turning Off the ignition will deactivate the Electric Rear Window Defroster and Heated side view mirrors feature. These features also turn off after activation, when 15 minutes have elapsed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s microphone for private conversations. The UConnect™; phone book enables you to store up to 32 names and four numbers per name. This system is driven through your Bluetooth™ Hands-Free Profile cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 The UConnect™ system is fully integrated into your vehicle, including your vehicle’s stereo system. All voice prompts as well as the other party’s voice in a conversation will be played over your vehicle’s stereo system. The volume of the UConnect™ system can be controlled through your normal stereo controls. The radio display will be used for visual prompts from the UConnect™ system such as caller ID.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnect™ system will then prompt you to begin the cellular phone pairing process on your cellular phone. Please see your cellular phone user’s manual for instructions on how to complete this step. • For identification purposes, you will be prompted to give the UConnect™ system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 Add Names to Your UConnect™ Phonebook • Press the “Phone” button to begin. • After the ⬙Ready⬙ prompt, say ⬙Phonebook New Entry⬙. • Or, After the ⬙Ready⬙ prompt, say “Phonebook”. • When prompted, say “New Entry”. • When prompted, say the name of the new entry. • Next, enter the number designation (e.g. “Home”, “Work”, “Mobile”, or “Pager”). This will allow you to have multiple numbers for each phonebook entry.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu. Delete Entries in the UConnect™ Phonebook Phonebook edit can be used to add another phone number to a name entry that already exists in the phonebook.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Phonebook Delete All⬙. • The UConnect™ system will ask you to verify that you wish to delete all the entries from the phonebook. • After confirmation, the phonebook entries will be deleted. List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Phonebook List Names⬙.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect™ system will interrupt the stereo audio and will ask if you would like to answer the call by pressing the ’Phone’ button. Press the ’Phone’ button to answer the call. To reject the call, press the ’Phone’ button until you hear a single beep indicating that the incoming call was rejected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Toggling Between Two Calls If two calls are in progress (one active and one on hold), press the ’Phone’ button until you hear a single beep indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time. Call Termination To end a call in progress, press the ’Phone’ button. All calls in progress will be terminated.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Advanced Phone Connectivity Transferring an Active Call between the UConnect™ System and Your Cellular Phone The UConnect™ system allows ongoing calls to be transferred to your cellular phone or to the UConnect™ system without terminating the call. To transfer an ongoing call from your cellular phone to the UConnect™ system or vice versa, press the ’Voice Recognition’ button and say ⬙Transfer Call⬙.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 List Paired Cellular Phone Names • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Setup List Phones⬙ and the UConnect™ system will play the phone names of all paired cellular phones in order from highest priority to lowest priority. Select a Lower Priority Paired Cellular Phone • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Setup⬙. • When prompted, say “Select Phone”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE are pressing a number on your keypad to navigate through a menu structure or to enter a number for a pager. Barge In - Overriding Prompts The ’Voice Recognition’ button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect™ system. By dialing a number with your paired Bluetooth™ cellular phone, the audio will be played through your vehicle’s stereo system. The UConnect™ system will work the same as if you dialed the number using voice recognition.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS The seating options available in this truck are the result of extensive customer research and evaluations. WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 WARNING! You can be seriously, even fatally injured riding in a seat with the seatback reclined. Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. If you ride in this position, the shoulder harness will no longer be restraining you. In a collision you could slide under the seat belt and receive serious or fatal injuries. Recline in a seat only when the vehicle is parked.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Driver Seat CAUTION! Don’t put anything under a power seat. It may cause damage to the seat controls. Up, Down, Forward, and Rearward The power seat controls are on the outboard side of the front seat cushions. Three switches control the seat movement. The four-way switch in the center can be moved forward or backwards to get the most comfortable position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 control seat height. Change the seat angle by using the two toggle switches, tilting it up or down. Manual Passenger Seat 3 Passenger Side Manual Tilt Adjustment The passenger seat is adjustable forward or backward and is equipped with a back recliner.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Seatback Recline The recliner mechanism control is on the outboard side of the seat. To recline, lean forward slightly, lift the lever, then push back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position. Using body pressure, lean forward and rearward on the seat to be sure the seatback has latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 To lower the head restraint, push in the button and then push down on the head restraint. TO OPEN AND CLOSE THE HOOD 3 To open the hood, two latches must be released. First pull the hood release lever located below the steering wheel at the base of the instrument panel. Once the hood is released you must reach into the opening beneath the center of the grille and push up the latch to release the safety catch before raising the hood.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are latched fully before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 LIGHTS Interior Lights 3 Courtesy/ dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the second upward detent position, or if equipped, when the UNLOCK button is pressed on the key fob.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE turn on the cargo light located on the back of the cab. When a door is open and the interior lights are on, rotating the dimmer control all the way down to the OFF detent will cause all the interior lights to go out. This is also known as the ⬙Party⬙ mode because it allows the doors to stay open for extended periods of time without discharging the vehicle’s battery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Headlamp Delay — If Equipped To aid in your exit, your vehicle, if equipped, can be programmed by your dealer with a headlamp delay that will leave the headlamps on for 0, 30, 60, or 90 seconds. This delay is initiated when the ignition is turned OFF while the headlamp switch is on, and then the headlamp switch is cycled off. The headlamps will remain on for 60 seconds.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses. Daytime Running Lights (Canada and Fleet Vehicles Only) The headlights on your vehicle will illuminate when the engine is started.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 CARGO LIGHT The cargo lights are turned on by rotating the dimmer control to the optional fully upward position. The cargo lights will also turn on for 30 seconds when a key fob Unlock is pressed, as part of the illuminated entry feature. MULTIFUNCTION CONTROL LEVER The multifunction control lever is located on the left side of the steering column. Turn Signals Move the lever up or down to signal a right-hand or left-hand turn.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Passing Light You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steering wheel. This will cause the high beam headlights to turn on until the lever is released. High Beam / Low Beam Select Switch Pull the multifunction control lever fully toward the steering wheel to switch the headlights from HIGH or LOW beam.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Windshield Wipers Intermittent Wiper System 3 The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed. The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The delay interval decreases as you rotate the knob until it enters the LO continual speed position. The delay can be regulated from a maximum of about 15 seconds between cycles, to a cycle every 2 seconds. The delay intervals will double in duration when the vehicle speed is 10 mph (16 km) or less. WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 TILT STEERING COLUMN To tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Push the lever back up to lock the column firmly in place. WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER ADJUSTABLE PEDALS Adjustment 1. Position the driver seat so that you are at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel. 2. Fasten and adjust the seatbelts. 3. Move the adjustable pedal switch, located to the left of the steering column near the parking brake release, in the direction you desire to move the pedals. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. ELECTRONIC SPEED CONTROL When engaged, this device takes over accelerator operation at speeds greater than 35 mph (56 km/h). The controls are mounted on the steering wheel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate Push the ON/OFF button to the ON position. In the instrument cluster, the word “CRUISE” illuminates when the system is on. To Set At A Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 tapped, speed increases so that tapping the button three times will increase speed by three increments. Tapping the COAST button once will result in a speed decrease of 1 mph (2 km/h). Each time the button is tapped, speed will decrease. For example, tapping the button 3 times will decrease the speed by 3 mph (6 km/h). To decrease speed while the speed control is on, press and hold the COAST button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE The overhead console consists of the following features: Courtesy/Reading Lights In the middle of the console are two courtesy/reading lights. Both lights illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (fully upward position), or when the UNLOCK button is pressed on the Remote Keyless Entry transmitter, if so equipped.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 COMPASS/TEMPERATURE MINI-TRIP COMPUTER This overhead console consists of the following: US/M Button • Courtesy Lights • Compass/Temperature Mini-Trip Computer 3 • Universal Garage Door Opener This overhead console allows you to choose between a compass/temperature display and one of four trip conditions being monitored. Use this button to change the display from U.S. to metric measurement units.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE RESET Button Global Reset If the RESET button is pressed twice within 4 seconds while in any of the 3 resettable displays, the Global Reset will reset all 3 displays. Step Button Use this button to reset the following displays to zero: Average Fuel Economy Trip Odometer Elapsed time Use this button to choose or cycle through the four trip conditions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. This display mode becomes less sensitive to instantaneous changes in fuel consumption as the number of total vehicle miles since the last reset increases.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Elapsed Time (ET) This display shows the accumulated ignition ON time since the last reset. C/T Button WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible personal injury or property damage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Manual Compass Calibration NOTE: To ensure proper compass calibration, make sure the compass variance is properly set before manually calibrating the compass. If the compass appears erratic and the CAL symbol does not appear, you must manually put the compass into the “Calibration” mode. To Put Into a Calibration Mode Turn on the ignition and set the display to “Compass/ Temperature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass Variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set according to the Compass Variance Map.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press the RESET button approximately five seconds. The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE For additional information on HomeLink威, call 1–800– 355–3515, or on the internet at www.homelink.com. WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects. WARNING! Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run the vehicle’s exhaust while training the transceiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Some gate operators and garage door openers may require you to replace this Programming Step 3 with procedures noted in the ⬙Gate Operator/Canadian Programming⬙ section. 4. The HomeLink indicator light will flash slowly and then rapidly after HomeLink successfully receives the frequency signal from the hand-held transmitter. Release both buttons after the indicator light changes from the slow to the rapid flash. 5.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 8. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink button. Repeat the ⴖpress/hold/releaseⴖ sequence a second time, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink should now activate your rolling code equipped device.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties or questions, contact HomeLink at: www.homelink.com or 1-800-355-3515.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof - Express Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. This is called Express Open. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Closing Sunroof - Express Press the switch forward and release, and the sunroof will close automatically from any position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. NOTE: The sunshade cannot be closed if the sunroof is open. Ignition Off Operation The power sunroof switches remain active for 10 minutes after the ignition switch has been turned off. Opening either front door will cancel this feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS The auxiliary electrical outlets can provide power for in cab accessories designed for use with the standard “cigar lighter” plugs. One of the outlets is the cigar lighter outlet, located in the instrument panel below the ash receiver. This outlet has a fused direct feed from the battery so it receives power whether the ignition is ON or OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 CIGAR LIGHTER AND ASH RECEIVER The ash receiver is opened and closed by pushing on the front surface of the receiver and then allowing the receiver to open. The cigar lighter is located in the instrument panel below the ash receiver. NOTE: This outlet has a fused direct feed from the battery so it receives power whether the ignition is ON or OFF. Leaving items such as cell phones in this outlet when the engine is not running will cause the battery to run down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS STORAGE Front Cupholders The cupholders consist of two cupwells for passenger convenience. Center Storage Compartment The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid. Push the button on the front of the armrest to raise the cover.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 configure the storage area into compartments. For example, compartments can be configured to hold a lap-top computer, a cellular telephone, CD’s and miscellaneous items. The top of the cover provides a generous firm surface to serve as a desktop for your “mobile office.” WARNING! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE There is also storage behind the seat. This storage area contains the 10 inch subwoofer (if equipped). PICKUP BOX The pickup box on your new Ram has many features designed for utility and convenience. NOTE: If you are installing a toolbox to the front of the pickup box, you must use Mopar威 toolbox brackets available from your dealer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 You can carry wide building materials (sheets of plywood, etc.) by building a raised load floor. Place lumber across the box in the indentations provided above the wheel housings and in the bulkhead dividers to form the floor. WARNING! The pickup box is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. WARNING! • Care should always be exercised when operating a vehicle with unrestrained cargo.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE There are stampings in the sheet metal on the inner side bulkheads of the box in front of and behind both wheel housings. Place wooden boards across the box from side to side to create separate load compartments in the pickup box. There are four tie-down cleats bolted to the lower sides of the pickup box that can sustain loads up to 1000 lbs (450 kg) total. SLIDE-IN CAMPERS DO NOT use slide-in campers on SRT-10 models.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 3
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instruments And Controls . . . . . . . . . . . . . . . . . 132 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 133 䡵 Instrument Cluster Description . . . . . . . . . . . . . 134 䡵 Electronic Digital Clock . . . . . . . . . . . . . . . . . . 141 ▫ Clock Setting Procedure . . . . . . . . . . . . . . . . . 141 䡵 Sales Code RBQ—AM/FM Stereo Radio With 6 Disc CD Changer . . . . . . . . . . . . . . . . . . . . . . . 141 ▫ Radio Operation . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENTS AND CONTROLS
UNDERSTANDING YOUR INSTRUMENT PANEL 133 INSTRUMENT CLUSTER 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Malfunction Indicator Light This light is part of an onboard diagnostic system which monitors the emissions and engine control system. If the vehicle is ready for emissions testing the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started.
UNDERSTANDING YOUR INSTRUMENT PANEL 135 2. Voltage Gauge When the engine is running, the gauge indicates the electrical system voltage. The pointer should stay within the normal range if the battery is charged. Typically this would be between 12 and 14 volts. If the pointer moves to either extreme left or right and remains there during normal driving, the electrical system should be serviced. CAUTION! Do not operate the engine with the tachometer pointer at high rpm for extended periods.
UNDERSTANDING YOUR INSTRUMENT PANEL unbuckled, a chime will sound. After the bulb check or when driving, if the driver seat belt remains unbuckled, the Seat Belt Warning Light will flash or remain on continuously. Refer to ⬙Enhanced Driver Seat Belt Reminder System (BeltAlert)⬙ in the Occupant Restraints section for more information. 8. Speedometer The speedometer shows the vehicle speed in miles per hour and/or kilometers per hour. 9.
UNDERSTANDING YOUR INSTRUMENT PANEL 137 12. Temperature Gauge The temperature gauge indicates engine coolant temperature. Any reading within the normal range (less that the red zone) indicates that the cooling system is operating satisfactorily. The gauge needle will likely indicate a higher temperature when driving in hot weather, up mountain grades, in heavy traffic. If the needle rises into the red zone, stop the vehicle, shift into N (Neutral), and increase the engine idle speed for 2 to 3 minutes.
UNDERSTANDING YOUR INSTRUMENT PANEL 15. CHECK GAGES This light illuminates when the Voltmeter, Engine Oil Pressure or Engine Coolant Temperature gages indicate a reading either too high or too low. Examine the gages carefully, and follow the instructions above for each indicated problem. the ABS indicator light has a malfunction. This light will flash if the engine is running and the parking brake is on.
UNDERSTANDING YOUR INSTRUMENT PANEL 139 ON position and may stay on for five seconds. If the ABS light remains on or comes on during driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required. See your authorized dealer immediately. The ABS light could also illuminate during loss of traction and remain illuminated until the brake pedal is pressed. 18. Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven.
UNDERSTANDING YOUR INSTRUMENT PANEL 20. LOW WASH Light This light comes on when the washer fluid level falls below approximately 1/4 filled. The light will remain on until fluid is added and one minute has elapsed. 21. Odometer/Trip Odometer Button Press this button to toggle between the odometer and the trip odometer display. Holding the button in resets the trip odometer reading when in trip mode. 22. Fuel Gauge Shows level of fuel in tank when ignition switch is in the ON position. 23.
UNDERSTANDING YOUR INSTRUMENT PANEL 141 ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the “ON” or “ACC” position. SALES CODE RBQ—AM/FM STEREO RADIO WITH 6 - DISC CD CHANGER When the ignition switch is in the “OFF” position, or when the radio frequency is being displayed, time keeping is accurately maintained. 4 Clock Setting Procedure 1.
UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation Power/Volume Control Press the PWR/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio. Mode Press the MODE button repeatedly to select between AM, FM, the CD changer and Sirius Satellite Radio™ (if equipped). The display will show ST when a stereo station is received.
UNDERSTANDING YOUR INSTRUMENT PANEL 143 To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET RND button. SET 1 will show in the display window. Select the “1–6” button you wish to lock onto this station and press and release that button. If a button is not selected within 5 seconds after pressing the SET RND button, the station will continue to play but will not be locked into pushbutton memory.
UNDERSTANDING YOUR INSTRUMENT PANEL Time Button Press the TIME button to change the display between radio frequency and time. General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the Power / Volume control pushed ON before the CD player will operate.
UNDERSTANDING YOUR INSTRUMENT PANEL 145 If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. LOAD/ EJT — Load Press the LOAD/ EJT button and the button with the corresponding number where the CD is being loaded. After the radio displays “load” insert the CD into the player.
UNDERSTANDING YOUR INSTRUMENT PANEL Scan Press the Scan button to scan through each track on the CD currently playing. FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Random Play — SET / RND Press the RND button while the CD is playing to activate Random Play. This feature plays the tracks on the disc in random order to provide an interesting change of pace.
UNDERSTANDING YOUR INSTRUMENT PANEL 147 Program Type Information Jazz Foreign Language News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Radio Display Inform Jazz Language News Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R&B Sports Program Type Talk Top 40 Weather Radio Display Talk Top 40 Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to
UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SCAN button when the PTY icon is displayed, the radio will stop at every PTY station on the band and list each corresponding program type in the radio display. Time Press the TIME button to change the display from elapsed CD playing time to time of day. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual.
UNDERSTANDING YOUR INSTRUMENT PANEL 149 REMOTE SOUND SYSTEM CONTROLS The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. switch will decrease the volume. The center button of the right hand control will allow you to change the mode. The left hand control is a rocker type switch with a push button in the center. The function of the left hand control is different depending on which mode you are in.
UNDERSTANDING YOUR INSTRUMENT PANEL CD Player Pressing the top of the switch once will go to the next track on the CD. Pressing the bottom of the switch once will go to the beginning of the current track or to the beginning of the previous track if it is within one second after the current track begins to play. 3. Do not apply paper or tape to the disc; avoid scratching the disc. If you press the switch up or down twice it plays the second track, three times, it will play the third, etc. 6.
UNDERSTANDING YOUR INSTRUMENT PANEL 151 RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL snowflake button shows that the air conditioning is on. Press the button a second time to turn the air conditioning off. A/C Pushbutton Air Conditioning Operation To turn on the Air Conditioning, set the fan control at any speed and press the snowflake button located on the control panel. Conditioned air will be directed through the outlets selected by the mode control.
UNDERSTANDING YOUR INSTRUMENT PANEL 153 Recirculation Pushbutton Pushing the Recirculation button allows interior air to recirculate continuously in any position except defrost and defrost/floor mode for rapid cool down of the interior. See “Fast Cooldown” later in this section. Mode Control The mode control allows you to choose from several patterns of air distribution. NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes.
UNDERSTANDING YOUR INSTRUMENT PANEL Mix Blower Control Outside air flows in equal proportions through the floor and defroster outlets. Defrost Outside air is primarily directed to the windshield through the defroster outlets located at the base of the windshield and side window demist outlets. NOTE: The air conditioning compressor operates in both Mix and Defrost or a blend of these modes, even if the A/C button has not been pressed. This dehumidifies the air to help dry the windshield.
UNDERSTANDING YOUR INSTRUMENT PANEL 155 Dual Zone Temperature Control Use this control to regulate the temperature of the air inside the passenger compartment. This is accomplished by having separate temperature control slides for both the driver and front passenger. The blue area of the scale indicates cooler temperatures while the red area indicates warmer temperatures.
UNDERSTANDING YOUR INSTRUMENT PANEL edges of the instrument panel. The demisters also provide extra air ducts for circulation. They are in operation whenever the Floor, Mix or Defrost modes are in use. NOTE: When you turn off the engine you may hear a hissing sound from under the hood for a short period of time. This is a normal condition that occurs if the air conditioning system has been on. It is not an indication of a problem with the air conditioning system.
UNDERSTANDING YOUR INSTRUMENT PANEL 157 speeds will reduce fogging. Interior fogging on the windshield can be quickly removed by selecting the defrost mode. Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Chart
STARTING AND OPERATING CONTENTS 䡵 Ignition/Starter Switch . . . . . . . . . . . . . . . . . . . 162 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . . 164 ▫ Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 ▫ After Starting . . . . . . . . . . . . . . . . . . . . . . . . 165 ▫ Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 䡵 Transmission Shifting . . . . . . . . . . . . . . . . . . . . 165 ▫ On . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING ▫ Four-Wheel Anti-Lock Brake System (ABS) . . . 177 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . . 194 䡵 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 179 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . . 195 䡵 Tire Safety Information . . . . . . . . . . . . . . . . . . . 179 ▫ Alignment And Balance . . . . . . . . . . . . . . . . . 196 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 161 ▫ Fuel System Cautions . . . . . . . . . . . . . . . . . . 203 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . . . 204 䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 204 ▫ Fuel Filler Cap (Gas Cap) . . . . . . . . . . . . . . . 205 䡵 Catalytic Converter . . . . . . . . . . . . . . . . . . . . . 206 䡵 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . . . 208 ▫ Certification Label . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING IGNITION/STARTER SWITCH OFF Unlocks the steering wheel (if equipped with locking wheel). ON This is the normal running position. ACC Allows the electrical accessories to be used when the engine is not running. LOCK Engages the steering wheel lock (if equipped) when the steering wheel is turned.
STARTING AND OPERATING 163 STARTING PROCEDURES The starter should not be operated for more than 15second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. Manual Transmission Apply the parking brake, place the gearshift control lever in NEUTRAL and depress the clutch pedal to the floor before starting the vehicle. This vehicle is equipped with a clutch interlocking ignition system. It will not start unless the clutch is fully depressed.
STARTING AND OPERATING instrument panel and release when the engine starts. If the engine fails to start within 10 seconds, turn the key to the OFF position, wait 5 seconds, then repeat the normal starting procedure. If Engine Fails To Start If the engine fails to start after you have followed the normal starting procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine. This should clear any excess fuel in case the engine is flooded.
STARTING AND OPERATING 165 After Starting The idle speed is automatically controlled and will decrease as the engine warms up. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust temperatures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. WARNING! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death.
STARTING AND OPERATING “P” Park This gear position supplements the parking brake by locking the transmission. The engine can be started in this range. Never use Park while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply parking brake first, then place the selector in Park position.
STARTING AND OPERATING 167 WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal. “R” Reverse Use this range only after the vehicle has come to a complete stop.
STARTING AND OPERATING “1” First Use this position for driving up very steep hills and for engine braking at low speeds (20 mph [32 km/h] or less) when going downhill. NOTE: Do not exceed a maximum engine speed of 5500 rpm. Overdrive Operation The overdrive automatic transmission contains an electronically controlled fourth speed (Overdrive).
STARTING AND OPERATING 169 The transmission will downshift from Overdrive to Drive if the accelerator pedal is fully depressed at vehicle speeds above approximately 35 mph (56 km/h). Overdrive Operation The four-speed overdrive automatic transmission contains an electronically controlled fourth speed (Overdrive).
STARTING AND OPERATING • transmission has reached normal operating temperature. risen to a suitable temperature. Refer also to the Note under torque converter clutch, later in this section. The transmission will downshift from Overdrive to Drive if the accelerator pedal is fully depressed at vehicle speeds above approximately 35 mph (56 km/h). If the transmission temperature gets extremely hot, the transmission will automatically select the most desirable gear for operation at this temperature.
STARTING AND OPERATING 171 activated. Pressing the switch a second time restores normal operation. If the “TOW/HAUL” mode is desired, the button must be pressed each time the engine is started. is not shifting into Overdrive when cold. This is normal. Pressing the “TOW/HAUL” button, when the transmission is sufficiently warm, will demonstrate that the transmission is able to shift into and out of overdrive.
STARTING AND OPERATING This model is equipped with a clutch interlocking ignition system. The clutch pedal must be fully depressed to start the vehicle. Fully depress the clutch pedal before shifting gears. As you release the clutch pedal, lightly depress the accelerator pedal. When launching a stationary vehicle, keep the engine speed low until the clutch is fully engaged. Damage to the clutch can result from starting in 2nd or 3rd gear with a loaded vehicle.
STARTING AND OPERATING 173 Recommended Shift Speeds To use your manual transmission for fuel economy it should be upshifted as listed below. Shift at the vehicle speeds listed for acceleration. Earlier upshifts during cruise conditions (relatively steady speeds) will result in increased fuel economy, and may be used as indicated.
STARTING AND OPERATING LIMITED-SLIP DIFFERENTIAL The limited-slip differential provides additional traction on snow, ice, mud, sand and gravel, particularly when there is a difference between the traction characteristics of the surface under the right and left rear wheels. During normal driving and cornering, the limited-slip unit performs similarly to a conventional differential.
STARTING AND OPERATING 175 PARKING BRAKE The foot operated parking brake is positioned below the lower left corner of the instrument panel. To release the parking brake, pull the parking brake release handle. NOTE: The instrument cluster red brake warning light will come on and flash to indicate that the parking brake is applied. You must be sure that the parking brake is fully applied before leaving the vehicle.
STARTING AND OPERATING WARNING! • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury. Also be certain to leave a manual transmission in Reverse or first gear. Failure to do so may allow the vehicle to roll and cause damage or injury. • Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake or the gear selector lever.
STARTING AND OPERATING 177 Brake Noise During normal operation of the brake system certain noises may be present from time to time. Occasional ⬙groan⬙ or ⬙squeal⬙ noises may occur during normal operation of the brake system which may not be indicative of a problem. These noises may be heard at any time the brakes are applied but may be more noticeable during the first few brake applications in the morning.
STARTING AND OPERATING WARNING! WARNING! Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
STARTING AND OPERATING 179 POWER STEERING Your power steering system will provide mechanical steering capability if power assist is lost. TIRE SAFETY INFORMATION Tire Markings If for any reason the hydraulic pressure is interrupted, it will still be possible to steer your vehicle. Under these conditions you will experience a substantial increase in steering effort. 5 NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards.
STARTING AND OPERATING • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • Temporary Spare tires are high pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
STARTING AND OPERATING 181 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (ie. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING 183 Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure for passenger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar. For vehicles other than passenger cars, the cold tire inflation pressures are listed on either the “B” pillar, the Certification Label or in the Tire Inflation Pressures brochure in the glove compartment.
STARTING AND OPERATING 185 Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
STARTING AND OPERATING combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX pounds” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3.
STARTING AND OPERATING 187 5
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 1.
STARTING AND OPERATING 189 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. maximum loaded vehicle condition. These pressure conditions will be found in the “Supplemental Tire Pressure Information” section of this manual. 3.
STARTING AND OPERATING check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. CAUTION! Tire pressures change by approximately 1 psi (7 kPa) per 12° F (7° C) of air temperature change.
STARTING AND OPERATING 191 Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high speed vehicle operation.
STARTING AND OPERATING Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Always use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels). Never combine them with other types of tires. Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
STARTING AND OPERATING 193 Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result.
STARTING AND OPERATING WARNING! WARNING! The limited use spare tires are for emergency use only. Installation of this limited use spare tire affects vehicle handling. With this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly. Replace (or repair) the original tire at the first opportunity and reinstall it on your vehicle.
STARTING AND OPERATING 195 These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point. Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING 197 Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. SUPPLEMENTAL TIRE PRESSURE INFORMATION A light load vehicle condition is defined as two passengers {150 lbs (68 kg) each} plus 200 lbs (91kg) of cargo.
STARTING AND OPERATING CAUTION! To avoid damage to your vehicle, tires or chains, observe the following precautions: • Because of limited chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious vehicle damage. Stop the vehicle immediately if noise occurs that could suggest chain breakage. Remove the damaged parts of the chain before further use.
STARTING AND OPERATING 199 SNOW TIRES Snow tires should be of the same size and type construction as the front tires. Consult the manufacturer of the snow tire to determine any maximum vehicle speed requirement associated with the tire. These tires should always be operated at the vehicle maximum capacity inflation pressures under any load condition. While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires.
STARTING AND OPERATING Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed. NOTE: On Canadian vehicles only, if your Ram truck is equipped with All-Season type tires on the front and ON/OFF Road type tires mounted on the rear, do not use a front to back rotation pattern.
STARTING AND OPERATING 201 Poor quality gasoline can cause problems such as hard starting, stalling and hesitations. If you experience these symptoms, try another brand of “regular” gasoline before considering service for the vehicle. The manufacturer strongly supports the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability of engine and fuel system components.
STARTING AND OPERATING MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane. Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT. Gasolines blended with MMT reduce spark plug life and reduce emission system performance in some vehicles. The manufacturer recommends that gasolines without MMT be used in your vehicle.
STARTING AND OPERATING 203 Materials Added to Fuel All gasoline sold in the United States and Canada is required to contain effective detergent additives. The use of additional detergents or other additives is not needed under normal conditions. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance, damage the emission control system.
STARTING AND OPERATING Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
STARTING AND OPERATING 205 NOTE: Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is properly tightened. Make sure that the gas cap is tightened each time the vehicle is refueled. WARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle or on a truck bed. You could be burned. Always place gas containers on the ground while filling. Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door.
STARTING AND OPERATING WARNING! • Remove the fuel tank filler tube cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury. • The volatility of some gasolines may cause a buildup of pressure in the fuel tank that may increase while you drive. This pressure can result in a spray of gasoline and/or vapors when the cap is removed from a hot vehicle. Removing the cap slowly allows the pressure to vent and prevents fuel spray.
STARTING AND OPERATING 207 CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and vehicle.
STARTING AND OPERATING VEHICLE LOADING Certification Label As required by National Highway Traffic Safety Administration Regulations, your vehicle has a certification label affixed to the driver’s side door or pillar. This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Rating (GAWR) front and rear, and Vehicle Identification Number (VIN). A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.
STARTING AND OPERATING 209 Tire Size This is the minimum allowable tire size for your vehicle. Replacement tires must be equal to the load capacity of this tire size. Loading The actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation. Rim Size This is the rim size that is appropriate for the tire size listed.
STARTING AND OPERATING Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate. CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also overloading can shorten the life of your vehicle. An EXAMPLE of a loaded vehicle is shown in the following chart.
STARTING AND OPERATING 211 Gross Vehicle Weight Rating (GVWR) 6500 LBS. TRAILER TOWING All Dodge Ram Pickup trucks are intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alterations to standard equipment. Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package. See your Dodge dealer for package content.
STARTING AND OPERATING GROSS TRAILER WEIGHT (GTW) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its ⬙loaded and ready for operation⬙ condition. TRAILER SWAY CONTROL is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.
STARTING AND OPERATING 213 must be considered as part of the total load on your vehicle. Refer to the Certification label located at the driver’s door for the Gross Vehicle Weight Rating. WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Perform the maintenance listed in the “Maintenance Schedules” section of this manual (Section 8).
STARTING AND OPERATING 2500/3500 Models • The Axles on 2500/3500 Models are trailer tow ready and DO NOT REQUIRE any special axle lubes or additives. Trailer Towing Recommendations • All trailer hitches should be professionally installed on your vehicle. • Safety chains must always be used between your vehicle and trailer. • Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury.
STARTING AND OPERATING 215 • Be sure the trailer is loaded heavier in front, with 60% to 65% of the weight in front of the axle(s). Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents. (For a ⬙5th Wheel⬙ style trailer, this range of loading on the ⬙King Pin⬙ should be between 15% and 25%.
STARTING AND OPERATING Connecting Trailer Lighting And Electric Trailer Brakes NOTE: A 4-way trailer tow connector, located behind the bumper, is standard equipment on all Ram pickup models. This connector contains the following vehicle circuits: park/tail lamps, left stop/turn lamp, right stop/ turn lamp, and ground. With the optional Trailer Tow Prep package a 7-way connector is also provided with the following additional circuits: backup lamp, trailer battery and electric brake.
STARTING AND OPERATING 217 CAUTION! to 65% of the weight in the front of the trailer. This places 10% to 15% of the GTW on the tow hitch of your vehicle. Connect trailer lighting and brakes using factory harnesses only. Do not cut or splice wiring to the brake circuits. Use an approved wiring harness connector on the trailer. Trailer sway control and equalizing hitch are required for Class III or IV trailer hitches and tongue weights above 350 lbs (159 kg).
STARTING AND OPERATING Also, there are maximum tongue weight ratings that are not to be exceeded, as follows: 4.
STARTING AND OPERATING 219 Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or outboard, the mirror head should be rotated (flipped Out or In). A small blindspot mirror is integrated onto the main mirror surface.
STARTING AND OPERATING • Air Conditioning— turn it off temporarily. • Hilly Terrain— Turn overdrive off. See Cooling System Operating information in the Service and Maintenance section of this manual for more information. Automatic Transmission Oil Temperature Warning Light All vehicles with automatic transmissions are equipped with a transmission sump oil temperature sensor and warning light.
STARTING AND OPERATING 221 SNOWPLOW CAUTION! Dodge SRT-10 Models NOTE: DO NOT use Dodge SRT- 10 Models for snowplow applications. Using this vehicle for snowplow applications can cause damage to the vehicle. WARNING! WARNING! Snowplows, winches, and other aftermarket equipment should not be added to the front end or your vehicle. The airbag crash sensors may be affected by the change in the front end structure.
STARTING AND OPERATING TRACTION When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observed: 1. Slow down during rainstorms or when roads are slushy. 2. Slow down if road has standing water or puddles. 3.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Lights . . . . . . . . . . . . . . . . . . 224 ▫ Removing The Spare Tire . . . . . . . . . . . . . . . . 231 䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 225 ▫ Tire Changing Procedure . . . . . . . . . . . . . . . . 232 䡵 Jack Location . . . . . . . . . . . . . . . . . . . . . . . . . . 226 䡵 Hoisting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237 ▫ Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING LIGHTS The Hazard Warning switch is mounted on the top of the steering column as shown in the illustration. will flash off and on to warn oncoming traffic of an emergency. Push the button a second time to turn off the flashers. This is an emergency warning system and should not be used when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists.
WHAT TO DO IN EMERGENCIES 225 ADDING FUEL The fuel tank filler tube has a restriction about 2 inches (50 mm) inside the opening. If using a portable fuel container, it should have a flexible nozzle long enough to reach past the restriction. WARNING! A fire may result if gasoline is pumped into a portable container that is in a vehicle or on a truck bed. You could be burned. Always place gas containers on the ground while filling.
WHAT TO DO IN EMERGENCIES JACK LOCATION Removal The jack and jack tools are stored under the front passenger seat. Lift the flap on the side of the seat for access. Remove the jack and tools by removing the wing bolt and sliding the assembly from under the seat.
WHAT TO DO IN EMERGENCIES 227 WARNING! WARNING! The jack is designed to use as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes, unless suitable supports are placed under the vehicle as a safety measure. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. After using the jack and tools, always reinstall them in the original carrier and location.
WHAT TO DO IN EMERGENCIES Reinstalling The Scissors-Type Jack And Tools (SRT–10 Models) 1. Lower the jack all the way down by turning the jack turn-screw until the jack is snug. 2. Position the jack and tool bag (unrolled). Make sure the lug wrench is under the jack near the jack turn-screw.
WHAT TO DO IN EMERGENCIES 229 3. Fold the flap and roll the jack tool kit into a cylindrical package (in direction of arrows), and tie to the jack using the tie straps.
WHAT TO DO IN EMERGENCIES 4. Place the jack and tools in the storage position holding the jack by the jack turn-screw, slip the jack and tools under seat so that the bottom slot engages into the fastener on the floor and then secure to the floor pan using the wing bolt.
WHAT TO DO IN EMERGENCIES 231 CHANGING A FLAT TIRE Removing The Spare Tire Remove the spare tire before attempting to jack the truck. Attach the wheel wrench to the jack extension tube. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube. Rotate the wheel wrench handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle.
WHAT TO DO IN EMERGENCIES Tire Changing Procedure WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. Do not raise this vehicle using a bumper jack.
WHAT TO DO IN EMERGENCIES 233 1. Remove the spare wheel, jack, and tools from storage. Instructions WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised. • Apply the parking brake firmly before jacking. • Never start the engine with the vehicle on a jack.
WHAT TO DO IN EMERGENCIES 3. Placement of the Jack: • When changing a front wheel, place the scissors jack under the rear portion of the lower control arm as shown below. • Operate the jack using the jack drive tube and the wheel wrench. The tube extension, may be used, but is not required. • When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube.
WHAT TO DO IN EMERGENCIES 235 Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. 4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface. WARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5.
WHAT TO DO IN EMERGENCIES 9. Adjust the tire pressure when possible. NOTE: Do not oil wheel studs. For chrome wheels, do not substitute with chrome plated wheel nuts. Wheel Nuts All wheel nuts should be tightened occasionally to eliminate the possibility of wheel studs being sheared or the bolt holes in the wheels becoming elongated. This is especially important during the first few hundred miles of operation to allow the wheel nuts to become properly set.
WHAT TO DO IN EMERGENCIES 237 HOISTING A conventional floor jack may be used at the jacking locations, refer to the graphics that show jacking locations. However, a floor jack or frame hoist must never be used on any other parts or the underbody. CAUTION! Never use a floor jack directly under the differential housing of a loaded truck or damage to your vehicle may result. JUMP-STARTING You should not try to start your vehicle by pushing or towing.
WHAT TO DO IN EMERGENCIES WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush contaminated area immediately with large quantities of water. A battery generates hydrogen gas which is flammable and explosive. Keep flame or spark away from the vent holes.
WHAT TO DO IN EMERGENCIES 239 2. Park the booster vehicle within cable reach but without letting the vehicles touch. Set the parking brake on both vehicles, place transmission in Neutral, and turn the ignition OFF. 3. Turn off the heater, radio, and all unnecessary electrical loads. 4. Connect one end of a jumper cable to the positive terminal of the booster battery. Connect the other end of the same cable to the positive terminal of the discharged battery.
WHAT TO DO IN EMERGENCIES 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. WARNING! • Do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. • During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze.
WHAT TO DO IN EMERGENCIES 241 FREEING A STUCK VEHICLE If vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between FIRST and REVERSE, while applying slight pressure to the accelerator. In general, the least amount of accelerator pedal pressure to maintain the rocking motion without spinning the wheels or racing the engine is most effective.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment— 8.3L . . . . . . . . . . . . . . . 246 ▫ Drive Belts — Check Condition And Tension . . 254 䡵 Onboard Diagnostic System (OBD II) . . . . . . . . . 247 ▫ Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . 255 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . . 255 䡵 Dealer Service . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Front Suspension Ball Joints . . . . . . . . . . . . . . 261 ▫ Manual Transmission . . . . . . . . . . . . . . . . . . 271 ▫ Steering Linkage — Inspection . . . . . . . . . . . . 261 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 272 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . . 262 ▫ Front Wheel Bearings . . . . . . . . . . . . . . . . . . 274 ▫ Windshield Wiper Blades . . . . . . . . . . . . . . . . 262 ▫ Selection Of Lubricating Grease . . .
MAINTAINING YOUR VEHICLE 245 ▫ Center High-Mounted Stoplight With Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287 䡵 Recommended Fluids, Lubricants And Genuine Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291 ▫ Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 289 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291 䡵 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . 290 ▫ Chassis . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT— 8.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions and engine control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing. Normally, the OBD system will be ready. The OBD system may not be ready if your vehicle was recently serviced, if you recently had a dead battery, or a battery replacement.
MAINTAINING YOUR VEHICLE b. The MIL light will remain fully illuminated until the first engine crank or the key is turned off. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station. If your OBD system is not ready, you should see your dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update.
MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. REPLACEMENT PARTS Use of genuine Mopar威 parts for normal/scheduled maintenance and repairs is highly recommended to insure the designed performance.
MAINTAINING YOUR VEHICLE Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between the ADD and SAFE markings on the dipstick. Adding one quart of oil when the reading is at the ADD mark will result in a SAFE reading on these engines. 251 Change Engine Oil CAUTION! Overfilling or underfilling the crankcase will cause oil aeration or loss of oil pressure. This could damage your engine.
MAINTAINING YOUR VEHICLE • More than 50% of your driving is at sustained high speeds during hot weather, above 32°C (90°F) • Taxi, Police or delivery service (commercial service) • Off-road or desert operation • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual.
MAINTAINING YOUR VEHICLE 253 Engine Oil Identification (API) Symbol There is a symbol to aid you in selecting the proper engine oil. This symbol means that the oil has been certified by the American Petroleum Institute (API). We only recommend synthetic API Certified engine oils, such as Mobil 1威, that meet the requirements of Material Standard MS-10725. Use Mopar or an equivalent oil meeting the specification MS10725.
MAINTAINING YOUR VEHICLE Materials Added to Engine Oil Do not add any materials (other than leak detection dyes) to engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental additives. Disposing of Used Engine Oil And Oil Filters Care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, indiscriminately discarded, can present a problem to the environment.
MAINTAINING YOUR VEHICLE Spark Plugs Spark plugs must fire properly to assure engine performance and emission control. New plugs should be installed at the specified mileage. The entire set should be replaced if there is any malfunction due to a faulty spark plug, malfunctioning spark plugs can damage the catalytic converter. For proper type of replacement spark plugs, refer to the “Vehicle Emission Control Information” label in the engine compartment.
MAINTAINING YOUR VEHICLE Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.
MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may indicate severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE Crankcase Emission Control System Proper operation of this system depends on freedom from plugging due to deposits. As vehicle mileage builds up, the Crankcase Ventilation Valve orifice may accumulate deposits. If a valve is not working properly, replace it with a new orifice. DO NOT ATTEMPT TO CLEAN THE OLD ORIFICE! Check the ventilation hose for indication of damage or plugging deposits. Replace if necessary.
MAINTAINING YOUR VEHICLE 259 WARNING! CAUTION! Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Battery gas is flammable and explosive. Keep flame or sparks away from the battery. Don’t use a booster battery or any other booster source with an output greater than 12 volts.
MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants can cause the system to fail, requiring costly repairs. • Never add air conditioning refrigerant to correct a non-cooling problem unless pressure gauges are connected to the system by a certified technician.
MAINTAINING YOUR VEHICLE WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, tailgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed.
MAINTAINING YOUR VEHICLE To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution.
MAINTAINING YOUR VEHICLE WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, follow the preceding safety tips. Exhaust System Rubber Isolator and Loop-Type Hanger — If Equipped Inspect surfaces whenever the vehicle is hoisted for rubber to metal separation or deep cracks. SLIGHT CRACKING DUE TO WEATHERING DOES NOT ADVERSELY AFFECT PERFORMANCE.
MAINTAINING YOUR VEHICLE Check the coolant reserve tank tube for condition and tightness or connections at the reserve tank and radiator. Check the coolant pressure cap and coolant reserve system for proper vacuum sealing. With the engine at normal operating temperature, note the level of the coolant in the coolant reserve tank. Without removing the pressure cap (with the engine off), drain a small amount of coolant from the radiator draincock.
MAINTAINING YOUR VEHICLE Adding Coolant When adding coolant, or refilling the system, a minimum solution of 50% recommended HOAT ethylene glycol engine coolant (antifreeze) and distilled water should be used. Use higher concentrations (not to exceed 70%) if temperatures below ⫺34°F (⫺37°C) are anticipated. Use only high purity water such as distilled or deionized water when mixing the water/engine coolant solution.
MAINTAINING YOUR VEHICLE Recommended Engine Coolant Refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. CAUTION! • Mixing of coolants other than specified engine coolant, may result in engine damage, and decrease corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible. • Do not use plain water alone or alcohol base engine coolant (antifreeze) products.
MAINTAINING YOUR VEHICLE WARNING! Insure nylon tubing in these areas has not melted or collapsed. The warning words “DO NOT OPEN HOT” on the radiator pressure cap are a safety precaution. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present.
MAINTAINING YOUR VEHICLE The brake master cylinder has a translucent plastic reservoir. On the outboard side of the reservoir, there is a “MAX” dot and an “MIN” dot. The fluid level must be kept within these two dots. Do not add fluid above the MAX mark, because leakage may occur at the cap. With disc brakes the fluid level can be expected to fall as the brake linings wear. However, an unexpected drop in fluid level may be caused by a leak and a system check should be conducted.
MAINTAINING YOUR VEHICLE CAUTION! Do not allow a petroleum-base fluid to contaminate the brake fluid. Seal damage may result. Brake Hoses Inspection should be performed whenever the brake system is serviced or at intervals specified. Inspect hydraulic brake hoses for surface cracking, scuffing or worn spots. If there is any evidence of cracking, scuffing, or worn spots, the hose should be replaced immediately! Eventual deterioration of the hose can take place with possible burst failure.
MAINTAINING YOUR VEHICLE This inspection should be made with the vehicle in a level position. The fluid level should be 3/4” ± 1/4” below the plug on DANA M60 HD/248 mm rear axles. Drain and Refill Vehicles operated in normal service do not have regularly scheduled oil changes. If fluid has become contaminated with water or to provide the correct viscosity grade, drain and refill. Lubricant Selection Refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE the transmission. The fluid level should be at the bottom of the fill hole. Add fluid, if necessary, to maintain the proper level. Procedure For Checking Fluid Level To properly check the automatic transmission fluid level, the following procedure must be used: Frequency of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle.
MAINTAINING YOUR VEHICLE 6. Wipe the dipstick clean and reinsert until seated. Remove dipstick and note reading. a. If the fluid is hot, the reading should be in the crosshatched area marked “OK”. b. If the fluid is warm, the reading should be between the two holes. If the fluid level indicates low, add sufficient fluid to bring to the proper level. Fluid is added through the dipstick tube.
MAINTAINING YOUR VEHICLE It is important that proper lubricant is used in the transmission. Refer to Recommended Fluids, Lubricants and Genuine Parts for the correct lubricant type. A band adjustment and filter change should be made at the time of the oil change. The fluid and filter should be changed and the bands adjusted as specified in the Maintenance Schedule (Section 8). Vehicles having severe usage should follow Maintenance Schedule “B” of the Maintenance Schedule (Section 8).
MAINTAINING YOUR VEHICLE There are two groups identified, those for wheel bearings (Letter “G”) and those for chassis (Letter “L”) lubrication. Performance categories within these groups result in dual letter designations for each group. The letter designations shown in the example are the highest quality level available and when combined as shown can be used for both wheel bearing and chassis lubrication.
MAINTAINING YOUR VEHICLE The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. • Insects, tree sap and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants. Washing • Wash your vehicle regularly.
MAINTAINING YOUR VEHICLE 277 • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible.
MAINTAINING YOUR VEHICLE Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar威 Total Clean. Care should be taken to avoid soaking your leather upholstery with any liquid.
MAINTAINING YOUR VEHICLE 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 279 FUSE AND RELAY CENTER 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water.
MAINTAINING YOUR VEHICLE 2. Use specified fuses only. REPLACEMENT LIGHT BULBS 3. Always properly reinstall the cover. LIGHT BULBS — Inside Bulb No. Overhead Console Lights . . . . . . . . . . . . . . . TS 212-2 Dome Light. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7679 VEHICLE STORAGE If you are storing your vehicle for more than 21 days, we recommend that you take the following steps to minimize the drain on your vehicle’s battery: • Disconnect the Ignition-Off Draw fuse (I.O.D.
MAINTAINING YOUR VEHICLE 281 BULB REPLACEMENT Headlight (Halogen)/Front Park and Turn Lights CAUTION! This is a halogen bulb. Avoid touching the glass with your fingers. Reduced bulb life will result. 1. Remove the two (2) expanding fasteners from the headlight welt.
MAINTAINING YOUR VEHICLE NOTE: The lower bolt on the driver side headlight also retains the ambient temperature sensor between the headlight assembly and the frame. 2. Remove the three (3) bolts from the headlight housing.
MAINTAINING YOUR VEHICLE 283 7
MAINTAINING YOUR VEHICLE 3. Pull the housing out from the fender to allow room to disconnect the electrical connectors. 6. Remove housing from vehicle with headlight halogen bulb in housing. 7. Twist collar on headlight halogen bulb 1⁄4 turn and remove headlight bulb from the housing. 8. Replace headlight or turn signal bulb. Do not touch the headlight halogen bulb. 9. Reverse procedure for installation of bulbs and housing. 10. Tighten the outboard fastener first. 4.
MAINTAINING YOUR VEHICLE 285 Tail, Stop, Turn and Backup Lights 1. Remove the two (2) screws that pass through the bed sheetmetal. 3. Push the red lock slide in on the connector and remove the housing from the vehicle. 2. Pull the housing straight out from the body, with a quick motion, to separate the housing from the body. If not pulled straight, locators may be damaged.
MAINTAINING YOUR VEHICLE 4. Remove the four (4) screws from the bulb strip in the housing. 5. Pull the appropriate bulb straight from the bulb strip.
MAINTAINING YOUR VEHICLE 6. Reverse procedure for installation of bulbs and housing. 7. While holding the taillight firmly in place, fasten the top screw first. 287 Center High-Mounted Stoplight With Cargo Light 1. Remove the two (2) screws holding the housing/lens to the body as shown.
MAINTAINING YOUR VEHICLE 2. Separate the connector holding the housing and wiring harness to the body. • Outside Bulbs: Cargo Lamps 3. Turn desired bulb socket 1⁄4 turn and remove socket and bulb from housing. 4. Pull desired bulb straight from the socket. • Inside Bulb: Center High Mount Stop Lamp 5. Reverse procedure for installation of bulbs and housing.
MAINTAINING YOUR VEHICLE Fog Lights 289 2. Pull bulb straight from the connector. 1. Reach under the vehicle, unlock and twist connector counterclockwise 1⁄4 turn and remove connector and bulb from housing. 3. Reverse procedure for installation of bulbs and housing.
MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Metric 26 gal. 98L 8.5 qts. 8.0L 20 qts. 19L Fuel SRT-10 Models Engine Oil (with filter) 8.3L (SAE 0W-40 MS-10725) Cooling System 8.
MAINTAINING YOUR VEHICLE 291 RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluids, Lubricants and Genuine Parts Mopar威 Antifreeze/Coolant 5 Year/102,000 Mile Formula HOAT (Hybrid Organic Additive Technology) P/N 05066386AA or equivalent. We only recommend synthetic engine oils, such as Mobil 1威, that are API Certified and meet the requirements of Material Standard MS-10725.
MAINTAINING YOUR VEHICLE Chassis Component Manual Transmission Fluid Automatic Transmission Fluid Clutch Linkage Limited-Slip Rear Axle Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar Synthetic Manual Transmission Lubricant 75W/85W (Castrol Syntorq LT 75W/85W) Mopar威 ATF+4, Automatic Transmission Fluid. Multipurpose Grease, NLGI Grade 2 E.P. Mopar威 SAE 90W. Limited-Slip Rear Axles require the addition of 147 ml (5 oz.) Mopar威 limited slip additive.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . . . 294 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 297 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . . 294 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 294 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type in this section (Section 8) must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and S reliability.
MAINTENANCE SCHEDULES 295 M • Taxi, police, or delivery service (commercial service). • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual.
M 296 MAINTENANCE SCHEDULES A I At Each Stop for Fuel N T • Check the engine oil level about 5 minutes after a fully E warmed engine is shut off. Checking the oil level while N A the vehicle is on level ground will improve the accuN racy of the oil level reading. Add oil only when the C level is at or below the ADD or MIN mark. E S C H E D U L E S 8 • Check the windshield washer solvent and add if required. Once a Month • Check tire pressure and look for unusual wear or damage.
SCHEDULE “B” 297 M Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90° F C (32°). • Drag Race Operation. A I N • Taxi, police, or delivery service (commercial service).
M 298 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter at interval A shown or 3 months, whichever comes first. N C Drain and refill automatic transmission fluid. ReE place filter and adjust bands.* S C H E D U L E S 8 Rotate tires. Change rear axle fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary.
SCHEDULE “B” 299 M Miles (Kilometers) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. Drain and refill automatic transmission fluid. Replace filter and adjust bands. Rotate tires. Change rear axle fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect and replace, if necessary, the PCV valve.
M 300 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter at interval A shown or 3 months, whichever comes first. N C Drain and refill automatic transmission fluid. ReE place filter and adjust bands.* S C H E D U L E S 8 Rotate tires. Change rear axle fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary.
SCHEDULE “B” 301 M Miles (Kilometers) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. Drain and refill automatic transmission fluid. Replace filter and adjust bands. Rotate tires. Change rear axle fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Replace ignition cables. Inspect and replace, if necessary, the PCV valve.
M 302 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter at interval A shown or 3 months, whichever comes first. N C Drain and refill automatic transmission fluid. ReE place filter and adjust bands.* S C H E D U L E S 8 Rotate tires. Inspect engine air cleaner filter. Change rear axle fluid. Inspect brake linings. Inspect auto tension drive belt and replace if required.
SCHEDULE “B” 303 M Miles (Kilometers) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. Drain and refill automatic transmission fluid. Replace filter and adjust bands. Rotate tires. Change rear axle fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary. Inspect auto tension drive belt and replace if required.
M 304 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter at interval A shown or 3 months, whichever comes first. N C Rotate tires. E Flush and replace engine coolant. S C H E D U L E S 8 Flush and replace Power Steering Fluid. Inspect brake linings.
SCHEDULE “B” 305 M Miles (Kilometers) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. Drain and refill automatic transmission fluid. Replace filter and adjust bands.* Drain and refill automatic transmission fluid. Replace filter and adjust bands. Rotate tires. Change rear axle fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Replace ignition cables. Inspect and replace, if necessary, the PCV valve.
M 306 SCHEDULE “B” A I 105,000 108,000 111,000 114,000 117,000 120,000 N Miles T (Kilometers) (168 000) (173 000) (178 000) (182 000) (187 000) (192 000) E X‡ X‡ N Inspect auto tension drive belt and replace if A required. N ‡ This maintenance is not required if previously replaced. C * Drain and refill automatic transmission fluid. Replace E filter and adjust bands every 15, 000 miles if vehicle is S C H E D U L E S 8 used for frequent wide open throttle upshifts (For example Drag Racing).
SCHEDULE “A” 307 M Schedule “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs.
M 308 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Flush and replace engine coolant at 60 S C H E D U L E S 8 months, regardless of mileage. Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. Inspect and replace, if necessary, the PCV valve. Replace ignition cables.
SCHEDULE “A” 309 M Miles (Kilometers) [Months] Change engine oil and engine oil filter. Drain and refill automatic transmission fluid. Replace filter and adjust bands. Rotate tires. Flush and replace Power Steering Fluid. Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. Inspect and replace, if necessary, the PCV valve. Inspect auto tension drive belt and replace if required.
M 310 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Flush and replace engine coolant, if not done at 60 mos. S C H E D U L E S 8 102,000 (163 000) [102] X X X Flush and replace engine coolant, if not done at 102, 000 miles. Inspect brake linings. Inspect auto tension drive belt and replace if required. Replace ignition cables. Replace engine air cleaner filter. Replace spark plugs. Inspect and replace, if necessary, the PCV valve.
SCHEDULE “A” 311 M WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314 ▫ Prepare For The Appointment . . . . . . . . . . . . 314 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 314 ▫ Be Reasonable With Requests . . . . . . . . . . . . . 314 䡵 If You Need Assistance . . . . . . . . . . . . . . . . . . . 315 䡵 Warranty Information . . . . . . . . . . . . . . . . . . . . 317 䡵 Mopar威 Parts . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE 315 IF YOU NEED ASSISTANCE The manufacturer and its dealers are vitally interested in your satisfaction. We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to you selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
IF YOU NEED CONSUMER ASSISTANCE DaimlerChrysler Motors Corporation Customer Center P.O. Box 21–8004 Auburn Hills, MI 48321–8004 Phone: (800) 992-1997 DaimlerChrysler Canada Inc. Customer Center P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone —(800) 465–2001 In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F.
IF YOU NEED CONSUMER ASSISTANCE 317 contract, call the manufacturer’s Service Contract National Customer Hotline at 1-800-521-9922. The manufacturer will not stand behind any service contract that is not the manufacturer’s Service Contract. It is not responsible for any service contract other than the manufacturer’s Service Contract.
IF YOU NEED CONSUMER ASSISTANCE U.S.
IF YOU NEED CONSUMER ASSISTANCE 319 MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.
IF YOU NEED CONSUMER ASSISTANCE 321 Call Toll Free at 1–800–890–4038 (U.S.) or 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: www.techauthority.daimlerchrysler.com or www.daimlerchrysler.
INDEX 10
INDEX Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . 204,225 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 203 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 255 Air Conditioner Maintenance . . . . . . . . . . . . . . . 259 Air Conditioning Refrigerant . . . . . . . . . . . . . . . 259 Air Conditioning System . . . . . . . . . . . . . . . . . . 259 Air Conditioning System, Zone Control . . . . . . . . 151 Air Pressure, Tires . . . . . . . . . . . . . . . . . . .
INDEX 325 B-Pillar Location . . . . . . . . . . . . . . . . . . . . . . . . 184 Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292 Brake System . . . . . . . . . . . . . . . . . . . . . . . . 176,268 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 Disc Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . 268 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . 268 Parking . . . . .
INDEX Climate Control . . . . . . . . . Clock . . . . . . . . . . . . . . . . Clutch . . . . . . . . . . . . . . . Clutch Linkage Maintenance Compact Disc Maintenance . Compact Spare Tire . . . . . . Compass . . . . . . . . . . . . . . Compass Calibration . . . . . Compass Variance . . . . . . . Computer, Trip/Travel . . . . Console, Overhead . . . . . . . Contract, Service . . . . . . . . Converter, Catalytic . . . . . . Cooling System . . . . . . . . . Coolant Capacity . . . . . . Coolant Level . . .
INDEX 327 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Door Opener, Garage . . . . . . . . . . . . . . . . . . . . . 113 Drive Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254 Electric Rear Window Defrost . . . . . . . . . . . . . 73,155 Electrical Power Outlets . . . . . . . . . . . . . . . . . . . 122 Electronic Speed Control . . . . . . . . . . . . . . . . . . . 103 Emergency Brake . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Engine Oil Disposal . . . . . . . . . . . . . . . . . . . . 254 Flashers Turn Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Flat Tire Stowage . . . . . . . . . . . . . . . . . . . . . 231,236 Flooded Engine Starting . . . . . . . . . . . . . . . . . . . 164 Fluid, Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . 292 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . . 290 Fluid Level Checks Manual Transmission . . . . . . . . . . . . . . . . . . .
INDEX 329 Hands-Free Phone . . . . . . . . . . . . . . . . . . . . . . . . 73 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . . 224 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . 95,281 High Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 High Beam/Low Beam Select Switch . . . . . . . . . 98 Lights On Reminder . . . . . . . . . . . . . . . . . . . . . 96 Passing . . . . . . . . . . . . . . . . .
INDEX Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11,14 Lane Change and Turn Signals . . . . . . . . . . . . . . . 97 Lap Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . 29 LATCH (Lower Anchors and Tether for CHildren) . 55 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66,93 Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50,135 Anti-Lock Warning . . . . .
INDEX 331 Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Power Door . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Steering Wheel . . . . . . . . . . . . . . . . . . . . . . . . . 14 Lower Anchors and Tether for CHildren (LATCH) . 55 Lubricants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 Lubrication, Body . . . .
INDEX Filter Disposal . . . . . . . . . . . . . . . . . . . . . . . . 254 Identification Logo . . . . . . . . . . . . . . . . . . . . . 253 Materials Added to . . . . . . . . . . . . . . . . . . . . . 254 Pressure Gauge . . . . . . . . . . . . . . . . . . . . . . . 136 Recommendation . . . . . . . . . . . . . . . . . . . . . . 252 Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253 Onboard Diagnostic System . . . . . . . . . . . . . . . . 247 Opener, Garage Door . . . . . . . . . . .
INDEX 333 Programmable Electronic Features . . . . . . . . . 114,118 Programming Transmitters . . . . . . . . . . . . . . 114,118 Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . . 192 Radiator Cap (Coolant Pressure Cap) . . . . . . . 265,267 Radio (Sound Systems) . . . . . . . . . . . . . . . . . . . . 141 Rear Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270 Recommended Fluids, Lubricants and Genuine Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Security Alarm (Theft Alarm) . . . . . . . . . . . . . 24,137 Selection of Coolant . . . . . . . . . . . . . . . . . . . . . . 291 Selection of Oil . . . . . . . . . . . . . . . . . . . . . . . . . 252 Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Service Assistance . . . . . . . . . . . . . . . . . . . . 314,315 Service Contract . . . . . . . . . . . . . . . . . . . . . . . . . 316 Service Manuals .
INDEX 335 Sulfur in Gasoline . . . . . . . . . . . . . . . Sun Roof . . . . . . . . . . . . . . . . . . . . . . Supplemental Tire Pressure Information Synthetic Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202 119 197 253 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Tailgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Tether Anchor, Child Restraint . . . . . . . . . . . . .
INDEX Towing Disabled Vehicle . . . . . . . . . . . . . . . . . . . . . . . 241 Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218 Trailering . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218 Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . 211 Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 337 Warning Lights (Instrument Cluster Description) . 134 Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . 5 Warranty Information . . . . . . . . . . . . . . . . . . . . . 317 Washers, Windshield . . . . . . . . . . . . . . . . . . 100,262 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 276 Wheel Alignment and Balance . . . . . . . . . . . . . . . 196 Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . . 277 Wheel Changing . . . . . . . . . . . . . . . . . . .
NOTES
NOTES
NOTES
NOTES
NOTES
NOTES
NOTES
