User Manual
- SMART TRANSLATION MACHINE -
vol -
vol +
Me
KEY SPECIFICATION
USB
Power
Volume +/-
Return
B
A
*Double click any key to unlock the screen.
A/B: Left and right translation language of the
display interface.
Return: Only one level up operation can return.
Volume +/- : Adjust volume.
Power: Short press lock screen / wake up screen,
long press shutdown / power on.
USM: Connect USB cable or charge or connect
headset
PREPARATION
CHARGING
Please check that the accessories in the package
are all present before using this device: Language
translator, charging cable, user manual, and
certificate.
Wireless network: After starting the device, the
wireless network can be configured following
these steps:
When the device is in low-power mode, the
battery icon on the Status Bar will turn into an
low-power mode as well. While in low-power
mode, some functions of the device may not work
properly. When the battery is below 3.4V, the
device will automatically shut down to protect the
data. Restarting the device will need sucient
charging.
Launch “settings” and enter “WIFI” submenu.
Toggle on the switch.
Select the desirable wireless name (SSID)
and input the correct password if there is.
Click “Confirm” to connect.
While charging with device powered o, there
will be a charging icon with current battery
change in the center of the screen about 10
seconds after the cable is plugged in.
1
2
3
4
Charging with device power on, the battery
icon on the right top will turn into a charging
state.
When charging is complete, a solid battery
icon will be presented.
Tap the language button at the top of the
Translate page to see the list of available
languages.
Swipe up and down to find the language you
need. Tap the name of the language to
activate it.
Long press the A/B Button on the device to
trigger the Speech-Recognition mode (A
Button for the language on the left side, B
Button for the language on the right side).
POWER ON / OFF
WAKE UP / SLEEP
HOME SCREEN
POWER ON: Long press the Power Button until
the screen is on. The initialization of the device
may take some time, please wait a while.
POWER OFF: Long press the Power Button until a
dialog appears, select “Power O” to turn o the
device.
The home screen of the device is the entrance to
the core functions: Translate, Recording, Conver-
sation, Instant camera translation and Settings.
Manually: Sleep the device by short pressing on
the Power Button / Wake up the device by short
pressing on the Power Button.
Automatically: The device will go into sleep mode
automatically when there were no operations for a
period of time (Settings > Display, in this menu,
you can change the time it takes your device to go
to sleep) / Wake up the device by short pressing
on the Power Button.
Tapping on these icons will lead to the correspon-
ding function page.
There are two translation modes, online transla-
tion and oine translation. The device can change
translation mode automatically.
Online translation supports 107 dierent langua-
ges
Oine translation currently supports 12 langua-
ges. When the device is oine, it will automatica-
lly change to oine translation mode.
INTRODUCTION TO CORE
FUNCTIONS
LANGUAGE SELECTION
VOICE RECOGNITION
1
1
After releasing the A/B Button, the speech
will be automatically recognized and transla-
ted to the specified target language. The
translation starts automatically if voice
broadcast is enabled in the application
settings.
The list presents previous voice translation
results. Swipe up and down to review when
there are many records
Long press on the specific item in the list of
translated results will prompt a dialog.
Tap the "Favorites" option, and the specified
translation result will be marked as favorite.
Swiping to the right will take you to the
Favorites page.
Short click on any record and the audio will
start automatically. To clear the record, tap
and hold it.
Tap the three-dot icon at the top right of the
recording page to see the list of available
languages.
2 2
2
2
3
FAVORITES
RECORDING
CHOOSING THE SOURCE &
TARGETING LANGUAGES
Swipe up and down to find the language you
need. Tap the name of the language to
activate it.
In the Recording Page, to start recording,
click the 'microphone' icon at the bottom
right.
It will automatically identifies the source
language in the process of recording and
display it on the page.
Tap the ‘Language Switch’ icon at the bottom
left to view the original / translated text.
The recording function supports a maximum
of 1-hour recording.
Tap the red 'stop' icon at the bottom right to
prompt the confirmation.
Tap "OK" to stop and automatically save the
recording file.
Tap the three-dot icon at the top right to
view the list of saved recording files.
RECORDING RECOGNITION
SAVING RECORDING RESULTS
1
1
3
3
4
CONVERSATION
BRIEF INTRODUCTION
HOLD A MULTI-PERSON
CONVERSATION
The conversation function supports the recogni-
tion and broadcasting of languages over 107
countries, reducing the language barriers and
facilitating inter-person communications
Create a multi-person conversation (applicable
only if the device did not join any existing one
yet).
Invite to join multi-person conversation:
Tap the "Create" icon on the conversation
page.
Input the ID of the target device that you
need to invite, then click "Confirm".
Tap the "Done" button to complete the
creation.
In the Multi-person conversation page, click
the button at top right and select "Add
member" options.
Input the ID of the target device that needs
to join, then click "Confirm".
Tap "OK" to complete the invitation.
2
1
2
1
3
3
VOICE RECOGNITION
ADD A MEMBER
MEMBER MANAGEMENT
Long press on the A/B Buttons in the conver-
sation page to enter voice recognition mode.
Speak in the language that you have set in
the system as spoken input.
When you finish, then release the A/B
Buttons, the translation is done automatica-
lly.
2
1
3
2
1
3
Tap the button at the top right of the
Multi-person conversation page and select
"Settings" options.
Switch on/o "Automatic broadcast" will
enable/disable automatic message broad-
cast.
Switch on/o "Block information" will enable
/disable message blocking function
2
1
Tap the language button at the top of the
Translate page to see the list of available
languages.
Swipe up and down to find the language you
need. Tap the name of the language to
activate it.
Tap the button at top right of the Multi-per-
son conversation page and select "Select
language" options.
Set the language according to the actual
needs.
2
1
Long press the A/B Button on the device to
trigger the Speech-Recognition mode (A
button for the language on the left side, B
button for the language on the right side).
After releasing the A/B Button, the speech
will be automatically recognized and transla-
ted to the specified target language. The
pronunciation starts automatically if voice
broadcast is enabled in the application
settings.
The list presents previous voice translation
result. Swipe up and down to review when
there are many records.
2
3
1
Long pressing on the specific item in the list
of the translated results will prompt with a
dialog.
Tap the "Favorites" option, with a notice, the
specified translation result is marked as
favorite.
Short click on any record, the pronunciation
starts automatically. To clear the record, tap
and hold it.
2
3
1
In the Multi-person conversation page, click
the button at top right and select "Add
member" option.
Input the Chat ID of the target device that
you want to invite, then click "Confirm".
Tap "OK" to complete the invitation.
2
1
3
In the Multi-person conversation page, click
the button at the top right and select
"Member management" options.
Tap "Leave conference" to quit the convesa-
tion.
Tap the "X" button next to each member to
exclude the specific member.
2
1
3
LANGUAGE SELECTION
ADVANCED SETTINGS
LANGUAGE SELECTION
INSTANT CAMERA
TRANSLATION
VOICE RECOGNITION
FAVORITES
SETTINGS
ONLINE UPDATE
WIFI: Configure WIFI network for the devices.
Mode: You can choose either automatic broadcast
or manual broadcast mode. When you choose the
manual mode, the translation results will need to
be manually clicked to broadcast.
Bluetooth: You can connect you device with a
compatible Bluetooth enabled device.
Display: In this menu, you can change the time it
takes your device to go to sleep. The time limit
you can choose: 30 seconds, 1 minute, 3minutes,
never turn o.
Date & Time: automatic mode and manual mode
are available to choose.
Reset: reset the device to its factory state (delete
all user data on the device, and this cannot be
undone).
Firmware upgrade: Check information of the
existing version and new version.
About us: Check the model name, version
number, patent information of the device.
When there is a new upgradable version, the
device will check for it when the user switches
language, reboots the device, or 24 hours after
the previous check. Both WIFI and mobile
network are applicable for the update.