CONCERTO TM ALL-CHINA GRAVITY DISCHARGE TOILET INSTALLATION AND OPERATION INSTRUCTIONS Model 3210 Toilet for Recreation Vehicles ! WARNING This manual must be read and understood before installation, adjustment, service, or maintenance is performed. Modification of this product can result in property damage. Dometic Corporation 13128 State Rt. 226, P.O.
TABLE OF CONTENTS Toilet Model Identification ...................................... 2 Toilet Dimensions .................................................. 3 Installation Instructions..................................... 3 - 6 Toilet Operation ..................................................... 6 Proper Cleaning and Maintenance ......................... 7 Winterizing ............................................................ 7 Spare Parts ...........................................................
CONCERTOTM TOILET DIMENSIONS MODEL 3210 Dimensions may vary ±3/8-inch (13mm). INSTALLATION INSTRUCTIONS System Requirements: • 2 GPM (10.6 lpm) or larger water pump. • 1/2-inch (12.7 mm) water line terminating in 1/2-inch MPT fitting (to connect to toilet water supply hose). • 4-bolt floor (closet) flange. SeaLand flanges available include 3-inch spigot, socket, MPT, or 45-degree swivel socket. • 12 VDC through 2-amp fuse or circuit breaker. Use 14-gauge stranded copper wire.
STEP 5a: For through-the-floor water line and electrical wires, mark another centerline 6 inches (152 mm) from the back wall (fig. 4). Below-Floor Installation Fig. 4 STEP 5b: For through-the-wall water line and electrical wires, mark a centerline 8 inches (203 mm) up from the floor centerline (fig. 5). Above-Floor Installation Fig. 5 STEP 7: Insert floor flange into larger hole and secure to the floor with #12x3/4-inch long flat head wood or sheet metal screws (fig.7).
STEP 9: WITH THE ELECTRICAL POWER OFF, route #14 gauge stranded copper wire from 12 VDC ground and positive 12 VDC from the fuse panel through a 2-amp fuse or circuit breaker. Leave at least 12 inches (305 mm) of wire for connecting to toilet (fig. 9). STEP 13: Temporarily set the toilet in place on the floor flange (fig. 14). Fig. 9 Fig. 14 STEP 14: Mark the holes for the two toilet mounting bolts (fig. 15). STEP 10: Connect the holding tank to the bottom of the discharge flange.
STEP 17: Connect the positive (+) 12 VDC lead to the red wire and the negative (-) lead to the black wire (fig. 18). Fig. 18 Fig. 19 Fig. 20 STEP 18: REMOVE RED CAP FROM MIDDLE OF FLANGE ADAPTER BEFORE FINAL TOILET INSTALLATION. IMPORTANT – DO NOT ATTEMPT TO SLIDE THE TOILET OVER THE FLANGE ADAPTER. THE TOILET MUST BE SET DOWN OVER THE ADAPTER TO PREVENT POSSIBLE DAMAGE. Fig. 21 STEP 19: Set the toilet in place (fig. 19) and secure to floor with the #14x2-1/2 inch long lag bolts (fig. 20).
PROPER CLEANING AND MAINTENANCE The Concerto toilet should be cleaned regularly for maximum sanitation and operational efficiency. You can clean it just as you would a household toilet. Do not use caustic chemicals, such as drain-opening types, as they will damage the seals. BOWL CLEANING: For stubborn stains, use SeaLand Bowl and Seal Cleaner (fig. A). It’s manufactured especially for use with SeaLand ceramic toilets.
DEODORANTS AND SPECIAL TISSUE Your Concerto toilet requires the regular addition of a deodorant product to reduce malodors and to help break down holding tank contents. Several factors should be considered in selecting a deodorant product. Liquid or Dry: Liquid products obviously work more quickly by readily going into solution. Granulated powder formulations, on the other hand, have the advantage of requiring less storage space and are less likely to leak if the package is inadvertently damaged.
FLUSH MECHANISM COMPONENTS 3. Lift china toilet straight up from base and set it down just in front of floor flange. Turn off water to toilet and disconnect flexible water line. Disconnect power wires if necessary. 1. To access base assembly components, remove decorative screw caps and unscrew two bolts that hold china toilet to floor. 2. Remove access cover from top of china and set it aside.
TROUBLESHOOTING Important: Always turn off electrical power and water to the toilet for disassembly. Problem Possible Cause Service Instructions 1. Toilet emits odor (flush ball open). a. Odor emitting from base of toilet. b. Plugged holding tank vent line. a. Use SeaLand brand deodorants. b. Clear obstructions from vent line. 2. Water will not stay in bowl. a. Improper seal between flush ball and seal due to dirt or debris on underside of flush ball seal. b. Worn or damaged flush ball and seal. a.
PARTS LIST Item Part No. Description 1 385311001 385311002 385311003 385311004 385311005 385311006 385311007 Access Cover, White Access Cover, Bone Flush Switch Assembly Flush Handle Shaft Kit Seat and Lid, White Seat and Lid, Bone China Bowl, White (incl. item 1 and locking material) China Bowl, Bone (incl. item 2 and locking material) Bowl Seal Kit Ring, Base Insert Shaft, Flush Ball Kit J-Bolts (incl. nuts and washers) Plastic Nuts and Washers Concerto Base O-Ring, 3.1 x 3.5 x .
ORDERING PARTS Dometic is ready to assist you in the event service is required. Before calling, please have the following information available. Your cooperation in having this information ready is appreciated and allows us to better meet your needs. 1. Toilet Model Number 2. Serial Number 3. Part Number, Description and Quantity (see Parts List) CUSTOMER SERVICE There is a strong, worldwide network to assist in servicing and maintaining your sanitation system.
