COMFORT CONTROL CENTER 2 THERMOSTAT OPERATING INSTRUCTIONS PROGRAMMABLE THERMOSTAT MODEL 3314081.XXX WITH DEHUMIDIFY 3314080.XXX WITH OUT DEHUMIDIFY USA SERVICE OFFICE Dometic, LLC 2320 Industrial Parkway Elkhart, IN 46516 574-294-2511 CANADA Dometic, LLC 46 Zatonski, Unit 3 Brantford, ON N3T 5L8 CANADA 519-720-9578 3314149.018 For Service Center Assistance Call: 800-544-4881 REVISION Form No. 3314149.018 10/11 (Replaces 3314149.000) (French 3314169.
INTRODUCTION Congratulations! Your recreational vehicle manufacturer has equipped your RV with the most advanced RV thermostat. Your Dometic Comfort Control Center 2 thermostat (hereinafter referred to as the CCC 2 thermostat) has been designed for ease of operation and for many years of reliable service. Dometic, LLC reserves the right to modify appearances and specifications without notice. TABLE OF CONTENTS INTRODUCTION ....................................................................................
TABLE OF CONTENTS SYSTEM RESET PROCEDURE ................................................................................................................. 20 GENERAL INFORMATION.......................................................................................................................... 20 A. Reduce Heat Gain ................................................................................................................... 20 B. Disclaimer ........................................................
ABOUT YOUR NEW THERMOSTAT MAINTENANCE Once the system is completely installed, do a system reset: 1. Make sure the CCC 2 thermostat is in the OFF mode. See section, “C. Quick Reference To Control Buttons” on page (5). 2. Simultaneously press and hold the MODE and ZONE buttons. See section, “C. Quick Reference To Control Buttons” on page (5). 3. The LCD will display “IniT” and all available zones. 4. Release the MODE and ZONE buttons. 5. Press the ON/OFF button to exit system set up. 6.
SYSTEM RESET PROCEDURE ABOUT YOUR NEW THERMOSTAT When your unit was installed the appropriate dip switches on the electronic control board were turned ON to match your system configuration. Any time these settings are changed, a system reset will need to be done before the CCC 2 thermostat will recognize the updated selection. To do a system reset: 1. Make sure the CCC 2 thermostat is in the OFF mode. 2. Simultaneously press the MODE and ZONE buttons. The LCD will display “IniT” and all available zones.
PROGRAMMING & OPERATIONS SPECIAL FEATURES N. Power Interruption A. ON/OFF To turn ON the CCC 2 thermostat when the back light is OFF, first press any button to wake up the CCC 2 thermostat. Then press and release the ON/OFF button. The LCD will display the last programmed settings. To turn OFF the CCC 2 thermostat press the ON/OFF button and release. Only the time of day will display when the CCC 2 thermostat is in the OFF condition. B.
SPECIAL FEATURES PROGRAMMING & OPERATIONS J. Auto Generator Start (AGS) C. Temperature Format °F / °C On RVs equipped with an optional AGS Kit, the vehicle generator will automatically start when any zone calls for cooling and will shut OFF when zones reach set point. The Auto Generator Start (AGS) function will be implemented by an individual power module board configured for this function by setting the GEN Start DIP switch ON.
PROGRAMMING & OPERATIONS E. Zone Selection SPECIAL FEATURES G. Auxiliary Heat (Heat Pump Models Only) Press the ZONE button to cycle the LCD display through the available zone selections; “Zone 1,” “Zone 2”, “Zone 3,” and “Zone 4.” Only the available zones installed within your system will display. For more information on zones, see section, “B. Zone Control” on page (13).
SPECIAL FEATURES PROGRAMMING & OPERATIONS E. Examples Of Times Programmed G. Fan Speed Press the FAN button to select the desired fan speed. Each successive press will advance to the next available speed. Your selections will be “Auto,” “LOW,” “MED,” and “HIGH.” The fan will run continuously during “LOW,” “MED,” and “HIGH” fan settings. The fan will cycle ON and OFF with the thermostat on “AUTO” setting. For more information on auto fan, see section, “A. Auto Fan” on page (13). H.
PROGRAMMING & OPERATIONS I. Dehumidify Setting (Select Models) To set the dehumidify set-point, the system will need to be in a mode other than OFF. Press the DEHUMIDIFY button. The LCD will display the “dEHm” icon, the water droplet icon , and the humidity set-point. The set-point can be adjusted in 5% increments from 35% to 70%. Press the button to increase the set-point and the button to decrease the set-point. To disable the dehumidify operation, press and hold the DEHUMIDIFY button for 3 seconds.
SPECIAL FEATURES MODE DESCRIPTION The dehumidify feature does not permit operation under the following conditions: ● Outdoor temperature is below 40 °F (4 °C). Resumes operation above 45 °F (7 °C). ● Indoor temperature is below 62 °F (17 °C). Resumes operation above 65 °F (18 °C). ● Indoor temperature is above 100 °F (38 °C). Resumes operation below 97 °F (36 °C). ● When the zone with dehumidify is set to COOL mode and the indoor temperature is 2 °F / °C above the COOL mode set-point.
MODE DESCRIPTION SPECIAL FEATURES E. “FAN” - Fan Mode A. Auto Fan In FAN mode there are (4) fan speed selections: LOW: The fan operates continuously at low speed. MED: The fan operates continuously at medium speed. HIGH: The fan operates continuously at high speed. AUTO: The fan will be OFF. F. “FURN” / “AQUA” - Furnace Or Aqua (Hydronic) Heating Mode (Factory setting is “FURN”) To change the setting from “FURN” to “AQUA” or vice versa, simultaneously press the and buttons.
