CONCERTO ® ELECTRIC FLUSH, GRAVITY DISCHARGE TOILET OWNER’S MANUAL 3300 Series (with flush handle) 3400 Series (with remote flush switch) ! WARNING This manual must be read and understood before installation, adjustment, service, or maintenance is performed. Modification of this product can result in property damage. Dometic Corporation • Sanitation Systems 13128 State Rt 226, PO Box 38 Big Prairie, OH 44611 SeaLand Product Customer Service: 1-800-321-9886 (8:00 a.m. - 5:00 p.m.
TABLE OF CONTENTS Toilet Model Identification . . . . . . . . . . . . . . . . 2 Ordering Parts . . . . . . . . . . . . . . . . . . . . . . . . 2 Concerto Toilet Dimensions . . . . . . . . . . . . . . . 3 Toilet Installation Instructions . . . . . . . . . . 3 - 6 Remote Flush Switch Installation . . . . . . . . . . 7 Important Information Before Operation . . . . . 8 Electronic "Flush and Forget" Operation . . . . . 8 Toilet Controls . . . . . . . . . . . . . . . . . . . . . . . . . 8 Operating Instructions .
CONCERTOTM TOILET DIMENSIONS Dimensions may vary ±3/8-inch (13mm). TOILET INSTALLATION INSTRUCTIONS System Requirements: • 2 GPM (10.6 lpm) or larger water pump. • 1/2-inch (12.7 mm) water line terminating in 1/2-inch MPT fitting (to connect to toilet water supply hose). • 4-bolt floor (closet) flange. SeaLand flanges available include 3-inch spigot, socket, MPT, or 45-degree swivel socket. • 12 VDC through 7- or 8-amp fuse or circuit breaker. Use 14-gauge stranded copper wire.
STEP 5a: For through-the-floor water line and electrical wires, mark another centerline 6 inches (152 mm) from the back wall (fig. 4). Below-Floor Installation Fig. 4 STEP 5b: For through-the-wall water line and electrical wires, mark a centerline 8 inches (203 mm) up from the floor centerline (fig. 5). Above-Floor Installation Fig.
IMPORTANT: If replacing an existing toilet that uses a 2-bolt floor flange, drill two 5/16-inch dia. holes in old floor flange that align with two additional holes in floor flange adapter. Use two #10 or 12 x 1-1/2-inch wood screws and washers for these drilled holes, and two T-bolts with flat washers and nuts to fasten flange gasket and floor flange adapter to old floor flange. Do not use old hardware or seal. FOR MODEL 3400 TOILET WITH REMOTE SWITCH OPERATION, see page 7 for wall switch installation instructions.
STEP 19: Set the toilet in place (fig. 19) and secure to floor with the #14x2-1/2 inch long lag bolts (fig. 20). Install decorative bolt caps by pushing them onto bolt heads (fig. 21). STEP 16: With toilet close to floor flange, connect flexible water supply hose to the water line fitting (fig. 17). Fig. 17 STEP 17: Insert the positive (+) 12 VDC wire into position 1 of the green terminal block and tighten the screw securely.
MODEL 3400 REMOTE FLUSH SWITCH INSTALLATION 3400 series toilets feature a remote flush switch to control the “Flush” and “Add Water” functions. Follow the instructions below for switch installation. STEP 1: Select a location for the switch. 8 feet of cable (2.4 m) is provided. You may need to supply more wire, depending on how far you locate the switch from the toilet. STEP 2: Cut an opening 1-1/4” wide x 1-5/8” high (see diagram at right).
IMPORTANT INFORMATION BEFORE OPERATION 1. Fill freshwater tank and add deodorant to holding tank through toilet bowl. 2. Make sure all guests understand the operation of the toilet system. 3300 models: This flushing instruction label is located under the seat, and is easily read when the seat is raised. 3400 models: "Add Water" and "Flush" are clearly marked on the remote switch. 3. Shut off the toilet system before servicing and do not leave the vehicle with toilet system circuit breaker on. 4.
OPERATING INSTRUCTIONS 1. Adding More Water To Toilet Bowl Pull up the flush handle (3300 model) or push "Add Water" switch (3400 model) until the desired water level is attained. To prevent overflowing the toilet, a timer inside the control module limits the amount of water that can be added. 2. Flushing The Toilet Push the flush handle down (3300 model) or push "Flush" switch (3400 model) for a moment, then release it.
PROPER CLEANING AND MAINTENANCE The Concerto toilet should be cleaned regularly for maximum sanitation and operational efficiency. You can clean it just as you would a household toilet. Do not use caustic chemicals, such as drain-opening types, as they will damage the seals. BOWL CLEANING: For stubborn stains, use SeaLand Bowl and Seal Cleaner (Fig. A). It’s manufactured especially for use with SeaLand toilets. In certain locations where water is hard, a build-up of lime may dull the toilet bowl finish.
WINTERIZING At the end of each traveling season, the Concerto toilet system must be winterized for storage. The following procedure should be used: 1. Pump out waste holding tank. 2. Thoroughly flush toilet system with fresh water. 3. Drain freshwater tank. 4. Add freshwater antifreeze to freshwater tank. 5. Flush freshwater antifreeze and water mixture through toilet and into the waste holding tank. Each installation is different so amounts may vary.
FLUSH MECHANISM COMPONENTS 3. Lift china toilet straight up from base and set it down just in front of floor flange. Turn off water to toilet and disconnect flexible water line. Disconnect power wires and/or flush switch wires if necessary. 1. To access base assembly components, remove decorative screw caps and unscrew two bolts that hold china toilet to floor. 2. Remove access cover from top of china and set it aside.
TOILET SYSTEM ELECTRICAL SPECIFICATIONS 12VDC Maximum standby current (amps): Maximum operating current (amps): Flush motor locked rotor current (amps): Maximum voltage Minimum voltage: Input power wire size All other wires size: Fuse size (amps) .070 6.5 14.5 15 10 14 ga. 18 ga.
TROUBLESHOOTING A volt/ohmmeter (VOM) and the Toilet Wiring Diagram may be required for this section. Caution: Portions of this section will require that power be applied to the toilet. Keep hands away from the flush ball, motor drive arm and rotor shaft to prevent personal injury during testing and troubleshooting. The control module uses a microprocessor to provide all the automatic and timing functions. The module is under the access cover.
TROUBLESHOOTING (cont’d) ERROR CODE CORRECTIVE PROCEDURES Condition Corrective Action Mode Switch in SERVICE position. Return Mode Switch to NORMAL position. Valve Open Limit Switch problem. With the flush valve fully open, check the “VALVE OPEN” status light. If the light is off, then the Valve Open Limit Switch is out of alignment or defective, or related wiring is defective. Valve Closed Limit Switch problem. With flush valve in the fully closed position check the “VALVE CLOSED” status light.
TROUBLESHOOTING (cont’d) SYMPTOM 3. Flush valve will not close. Condition/Procedure Corrective Action Mode Switch is in SERVICE position: • Return switch to the “Normal” position. Foreign object prevents the flush valve from closing and the safety circuit locked flush valve in open position: • Reset the control circuit by putting the Mode Switch in the SERVICE position temporarily, then returning to the NORMAL position. If the flush valve did not close, go to next step.
TROUBLESHOOTING (cont’d) SYMPTOM 6. Water will not stay in bowl. Condition/Procedure Corrective Action Put Mode Switch in “Service” position: • Clean underside of flush valve ball seal of dirt and debris. Worn or damaged flush valve ball and seal: • Remove toilet from floor and remove base assembly from toilet and replace flush valve ball and seals. SYMPTOM 7. Water will not shut off and overflows the toilet.
WIRING DIAGRAMS 3300 SERIES (with flush handle) 3400 SERIES (with remote flush switch) 18
CUSTOMER SERVICE There is a strong, worldwide network to assist in servicing and maintaining your sanitation system. For the Authorized Service Center near you, please call from 8:00 a.m. to 5:00 p.m. (ET) Monday through Friday. You may also write us at Dometic Corp., P.O. Box 38, Big Prairie Ohio 44611. You may also contact or have your local dealer contact the Parts Distributor nearest you for quick response to your replacement parts needs. They carry a complete inventory for the SeaLand product line.
MANUFACTURER’S THREE-YEAR AND TEN-YEAR LIMITED WARRANTIES Dometic Corporation warrants, to the original purchaser only, that this Concerto® gravity discharge toilet, if used for personal, family or household-like purposes, is free from defects in material and workmanship for a period of three (3) years from the date of purchase.