Operating instructions

ManualsBrandsDometic ManualsHeat Pump630025

NOTENOTE

NOTE:

The auxiliary heat position is only used if:The auxiliary heat position is only used if:

The auxiliary heat position is only used if:

– You have a factory installed furnace operating from the

heat pump system thermostat.

– The outside temperature is above 40 degrees and you

wish to operate your furnace.

– For quick interior warm up.

– There is no 115 volt AC power available to operate your

heat pump and you must operate the furnace for your

comfort.

FanFan

Fan:

To circulate air without heating or cooling:

Set the SYSTEM SWITCH to OFF.

Set the FAN SWITCH to ON.

Hi/LowHi/Low

Hi/Low:

HIGH: Fan speed position

LOW: Fan speed position

DIGITAL THERMOSTAT OPERATIONDIGITAL THERMOSTAT OPERATION

DIGITAL THERMOSTAT OPERATION

Your air conditioner is operated from the control panel of

the electronic wall thermostat. When the furnace is con-

nected to this thermostat, it will operate from the same

control panel.

Identification and operational descriptions for all control

panel switches and display are listed below:

Liquid Crystal DisplayLiquid Crystal Display

Liquid Crystal Display: This display will be illuminated

any time the system is in operation.

The display shows the operator both the mode of the

display (indicated by the arrow at the left side of the

display), and the temperature for that mode.

There are three display modes: ACTUAL, COOL and

HEAT.

The operator may choose the mode he desires to view by

depressing the "MODE" switch. Each time the MODE

switch is depressed, the display advances to the next

mode. If the display is left in either COOL or HEAT, the

thermostat will automatically return the display to ACTUAL

in approximately three minutes.

A description of the three modes isA description of the three modes is

A description of the three modes is:

ACTUALACTUAL

ACTUAL: When in actual mode, the display is indicating

current room temperature.

COOL SETCOOL SET

COOL SET: When in COOL mode, the display is indicating

the current cooling setpoint temperature. At this time the

cooling system setpoint temperature may be adjusted up or

down to meet the individual's comfort level. See "Adjusting

Setpoint" for further instructions.

HEAT SETHEAT SET

HEAT SET: When in the HEAT mode, the display is

indicating the current heating system setpoint temperature.

At this time, the heating system setpoint temperature may

be adjusted up or down to meet the operator's comfort

level. See "Adjusting Setpoint" for further instructions.

All three display modes can be accessed without affecting

the operation of the system. The system operation will

remain normal unless a change is made to the setpoint to

force a change in the system operation.

System SwitchSystem Switch

System Switch: The system switch has four positions to

control the operation of the heating and cooling systems.

They are as follows:

COOLCOOL

COOL: When in the COOL position, the compressor will

cycle from the cooling system setpoint. Blower operation

will be controlled by the position of the Cooling Fan Switch.

HEATHEAT

HEAT: When in the heat position, the heating system

will cycle from the heating system setpoint. The heating

blower will operate per the heating system manufacturer

specifications.

OFFOFF

OFF: When in the OFF position, no thermostat or

system operation will occur. The liquid crystal will indicate

room temperature until backup power is depleted (approxi-

mately 2 minutes).

AUXILIARY HEATAUXILIARY HEAT

AUXILIARY HEAT:

Set the system switch to AUX. HEAT.

Set the FAN switch to AUTO.

NOTE: The AUXILIARY HEAT position is only used if:

You have a factory installed furnace operating from the

heat pump system thermostat.

The outside temperature is above 40 degrees and you wish

to operate your furnace.

For quick interior warm-ups.

There is no 115 volt AC power available to operate your

heat pump and you must operate the furnace for your

comfort.

FAN SWITCHFAN SWITCH

FAN SWITCH: The Fan Switch has four positions from

which to control the operation of the heat pump blower. The

fan switch controls operation of the blower only after the

system switch is place into the COOL or HEAT PUMP

position.

by Dometic

Display delayed 1 minute at turn on.

Actual

Cool

Heat

Set Temperature

HIGH

LOW

HIGH

AUTO

MODE UP DOWN

DIGITDIGIT

DIGIT

ALAL

THERMOSTTHERMOST

THERMOST

COOL

OFF

HEAT PUMP

AUX.HEAT

SYSTEM COOLING FANSYSTEM COOLING FAN

SYSTEM COOLING FAN