Operating instructions

ManualsBrandsDometic ManualsHeat Pump630025

CABLE ASSEMBLY CONNECTORCABLE ASSEMBLY CONNECTOR

CABLE ASSEMBLY CONNECTOR

NOTENOTE

NOTE: Pin 2 (red wire) is positive DC volts when ambient

(outside) air is above 40°F. Pin 1 (violet wire) is positive DC

volts when ambient (outside) air is below 40°F. When

ambient (outside) air is below 40°F., only "FAN LO ON" and

"HI ON" will operate in the heat pump.

If the above voltage checks are correct and the unit does not

operate correctly, check the thermostat.

To check the thermostatTo check the thermostat

To check the thermostat, first verify positive (+) DC is to

red wire (Pin 2), and negative (–) DC is to brown wire (Pin

7) at the back of the thermostat. Operating range is 10 to 16

volts DC.

With System Switch in COOL, Fan Switch in HI AUTO and

room temperature ABOVE setpoint temperature, you should

have voltage between brown wire (Pin 7) to black wire (Pin

4), yellow wire (pin 5) and blue wire (Pin 6). You should

NOTNOT

NOT

have voltage between brown wire to violet or white wires.

With room temperature BELOW setpoint temperature, you

should

NOTNOT

NOT have voltage between brown wire to violet,

white, black, yellow or blue wires.

NOTE:NOTE:

NOTE:

When setpoint temperature is changed above orWhen setpoint temperature is changed above or

When setpoint temperature is changed above or

below room temperature, there will be a three (3)below room temperature, there will be a three (3)

below room temperature, there will be a three (3)

minute delay in "active" terminalsminute delay in "active" terminals

minute delay in "active" terminals.

With System Switch in COOL, Fan Switch in LO AUTO and

room temperature ABOVE setpoint temperature, you should

have voltage between brown wire (Pin 7) to black wire (Pin

4) and yellow wire (P5). You should NOT have voltage

between brown wire to violet, white or blue wires. With room

temperature BELOW setpoint temperature, you should

NOT have voltage between brown wire to violet, white,

black, yellow or blue wires.

NOTE:NOTE:

NOTE:

When setpoint temperature is changed above orWhen setpoint temperature is changed above or

When setpoint temperature is changed above or

below room temperature, there will be a three (3)below room temperature, there will be a three (3)

below room temperature, there will be a three (3)

minute delay in "active" terminalsminute delay in "active" terminals

minute delay in "active" terminals.

With System Switch in COOL, Fan Switch in LO ON and room

temperature ABOVE setpoint temperature, you should have

voltage between brown wire (Pin 7) to black wire (Pin 4) and

yellow wire (Pin 5). You should NOT have voltage between

brown wire to violet, white or blue wires. With room temperature

BELOW setpoint temperature, you should have voltage be-

tween brown wire (Pin 7) to black wire (Pin 4). You should NOT

have voltage between brown wire to violet, white, yellow or blue

wires.

NONO

TE:TE:

TE:

When setpoint temperature is cWhen setpoint temperature is c

When setpoint temperature is c

hanghang

hang

ed aboed abo

ed abo

ve orve or

ve or

belobelo

belo

w rw r

w r

oom temperatureoom temperature

oom temperature

there will be a three (3) min there will be a three (3) min

there will be a three (3) min

uteute

ute

deladela

dela

y in "active" terminalsy in "active" terminals

y in "active" terminals.

With System Switch in COOL, Fan Switch in HI ON and room

temperature ABOVE setpoint temperature, you should have

voltage between brown wire (Pin 7) to black wire (Pin 4), yel-

low wire (Pin 5) and blue wire (Pin 6). You should NOT have

voltage between brown wire to violet or white wire. With room

temperature BELOW setpoint temperature, you should have

voltage between brown wire (Pin 7) to black wire (Pin 4) and

blue wire (Pin 6). You should NOT have voltage between brown

wire to violet, white or yellow wires.

NONO

TE:TE:

TE:

When setpoint temperature is cWhen setpoint temperature is c

When setpoint temperature is c

hanghang

hang

ed aboed abo

ed abo

ve orve or

ve or

belobelo

belo

w rw r

w r

oom temperatureoom temperature

oom temperature

there will be a three (3) min there will be a three (3) min

there will be a three (3) min

uteute

ute

deladela

dela

y in "active" terminalsy in "active" terminals

y in "active" terminals.

With System Switch in COOL, Fan Switch in LO ON and room

temperature ABOVE setpoint temperature, you should have

voltage between brown wire (Pin 7) to black wire (Pin 4) and

yellow wire (Pin 5). You should NOT have voltage between

brown wire to violet, white or blue wires. With room temperature

BELOW setpoint temperature, you should have voltage be-

tween brown wire (Pin 7) to black wire (Pin 4). You should NOT

have voltage between brown wire to violet, white, yellow or blue

wires.

NOTE:NOTE:

NOTE:

When setpoint temperature is changed above orWhen setpoint temperature is changed above or

When setpoint temperature is changed above or

below room temperature, there will be a three (3) minutebelow room temperature, there will be a three (3) minute

below room temperature, there will be a three (3) minute

delay in "active" terminalsdelay in "active" terminals

delay in "active" terminals.

With System Switch in COOL, Fan Switch in HI ON and room

temperature ABOVE setpoint temperature, you should have

voltage between brown wire (Pin 7) to black wire (Pin 4), yellow

wire (Pin 5) and blue wire (Pin 6). You should NOT have voltage

between brown wire to violet or white wire. With room tempera-

ture BELOW setpoint temperature, you should have voltage

between brown wire (Pin 7) to black wire (Pin 4) and blue wire

(Pin 6). You should NOT have voltage between brown wire to

violet, white or yellow wires.

NOTE:NOTE:

NOTE:

When setpoint temperature is changed above orWhen setpoint temperature is changed above or

When setpoint temperature is changed above or

below room temperature, there will be a three (3) minutebelow room temperature, there will be a three (3) minute

below room temperature, there will be a three (3) minute

delay in "active" terminalsdelay in "active" terminals

delay in "active" terminals.