Dometic 630025 : Operating instructions : Page 89

89

With System Switch in the OFF, Fan Switch in HI AUTO or

LO AUTO and room temperature ABOVE or BELOW

setpoint temperature, you should NOT have voltage be-

tween brown wire to violet, white, black, yellow or blue

wires.

With System Switch in OFF, Fan Switch in LO ON and

room temperature ABOVE or BELOW setpoint tempera-

ture, you should have voltage between brown wire (Pin 7)

to black wire (Pin 4). You should NOT have voltage

between brown wire to violet, white, yellow or blue wires.

With System Switch in OFF, Fan Switch in HI ON and room

temperature ABOVE or BELOW setpoint temperature, you

should have voltage between brown wire (Pin 7) to black

wire (Pin 4) and blue wire (Pin 6). You should NOT have

voltage between brown wire to violet, white or yellow wires.

With System Switch in HEAT PUMP, Fan Switch in HI

AUTO and room temperature ABOVE setpoint tempera-

ture, you should NOT have voltage between brown wire to

violet, white, black, yellow or blue wires. With room tem-

perature BELOW setpoint temperature, you should have

voltage between brown wire (Pin 7) to white wire (Pin 3),

black wire (Pin 4) and blue wire (Pin 6). You should NOT

have voltage between brown wire to violet or yellow wires.

NOTE:NOTE:

NOTE:

When setpoint temperature is changed aboveWhen setpoint temperature is changed above

When setpoint temperature is changed above

or below room temperature, there will be a three (3)or below room temperature, there will be a three (3)

or below room temperature, there will be a three (3)

minute delay in "active" terminalsminute delay in "active" terminals

minute delay in "active" terminals.

NOTE:NOTE:

NOTE:

When setpoint temperature is changed above orWhen setpoint temperature is changed above or

When setpoint temperature is changed above or

below room temperature, there will be a three (3) minutebelow room temperature, there will be a three (3) minute

below room temperature, there will be a three (3) minute

delay in "active" terminalsdelay in "active" terminals

delay in "active" terminals.

With System Switch in HEAT PUMP, Fan Switch in HI ON and

room temperature ABOVE setpoint temperature, you should

have voltage between brown wire (Pin 7) to black wire (Pin 4)

and blue wire (Pin 6). You should NOT have voltage between

brown wire to violet, white or yellow wires. With room tempera-

ture BELOW setpoint temperature, you should have voltage

between brown wire (Pin 7) to white wire (Pin 3), black wire (Pin

4) and blue wire (Pin 6). You should NOT have voltage between

brown wire to violet or yellow wires.

NOTE:NOTE:

NOTE:

When setpoint temperature is changed above orWhen setpoint temperature is changed above or

When setpoint temperature is changed above or

below room temperature, there will be a three (3) minutebelow room temperature, there will be a three (3) minute

below room temperature, there will be a three (3) minute

delay in "active" terminalsdelay in "active" terminals

delay in "active" terminals.

Before checking the thermostat for operation in AUX.Before checking the thermostat for operation in AUX.

Before checking the thermostat for operation in AUX.

HEATHEAT

HEAT, verify that DC volts (10 to 16) are available between the

green wire (+) and brown wire (–) at the back of the thermostat.

With System Switch in AUX HEAT, Fan Switch in HI AUTO and

room temperature ABOVE setpoint temperature, you should

NOT have voltage between brown wire to violet, white, black,

yellow or blue wires. With room temperature BELOW setpoint

temperature, you should have voltage between brown wire (Pin

7) to violet wire (Pin 1). You should NOT have voltage between

brown wire to white, black, yellow or blue wires.

NOTE:NOTE:

NOTE:

When setpoint temperature is changed above orWhen setpoint temperature is changed above or

When setpoint temperature is changed above or

below room temperature, there will be a three (3) minutebelow room temperature, there will be a three (3) minute

below room temperature, there will be a three (3) minute

delay in "active" terminalsdelay in "active" terminals

delay in "active" terminals.

With System Switch in AUX HEAT, Fan Switch in LO AUTO

and room temperature ABOVE setpoint temperature, you

should NOT have voltage between brown wire to violet, white,

black, yellow or blue wires. With room temperature BELOW

setpoint temperature, you should have voltage between brown

wire (Pin 7) to violet wire (Pin 1). You should NOT have voltage

between brown wire to white, black, yellow or blue wires.

NOTE:NOTE:

NOTE:

When setpoint temperature is changed above orWhen setpoint temperature is changed above or

When setpoint temperature is changed above or

below room temperature, there will be a three (3) minutebelow room temperature, there will be a three (3) minute

below room temperature, there will be a three (3) minute

delay in "active" terminalsdelay in "active" terminals

delay in "active" terminals.

With System Switch in AUX HEAT, Fan Switch in LO ON and

room temperature ABOVE setpoint temperature, you should

have voltage between brown wire (Pin 7) to black wire (Pin 4).

You should NOT have voltage between brown wire to violet,

white, yellow or blue wires. With room temperature BELOW

setpoint temperature, you should

With System Switch in HEAT PUMP, Fan Switch in LO

AUTO and room temperature ABOVE setpoint tempera-

ture, you should NOT have voltage between brown wire to

violet, white, black, yellow or blue wires. With room tem-

perature BELOW setpoint temperature, You should have

voltage between brown wire (Pin 7) to white wire (Pin 3) and

black wire (Pin 4). You should NOT have voltage between

brown wire to violet, yellow or blue wires.

NOTE:NOTE:

NOTE:

When setpoint temperature is changed aboveWhen setpoint temperature is changed above

When setpoint temperature is changed above

or below room temperature, there will be a three (3)or below room temperature, there will be a three (3)

or below room temperature, there will be a three (3)

minute delay in "active" terminalsminute delay in "active" terminals

minute delay in "active" terminals.

With System Switch in HEAT PUMP, fan switch in LO ON

and room temperature ABOVE setpoint temperature, you

should have voltage between brown wire (Pin 7) to black

wire (Pin 4). You should NOT have voltage between brown

wire to violet, white, yellow or blue wires. With room

temperature BELOW setpoint temperature, you should

have voltage between brown wire (Pin 7) to white wire (Pin

3) and black wire (Pin 4). You should NOT have voltage

between brown wire to violet, yellow or blue wires.