Operating instructions

ManualsBrandsDometic ManualsHeat Pump630025

100

C.C.

Relay, SPDT (single pole/double throw) is used onRelay, SPDT (single pole/double throw) is used on

Relay, SPDT (single pole/double throw) is used on

Models 39424.601, 39115.626, 39125.601, 39335.601Models 39424.601, 39115.626, 39125.601, 39335.601

Models 39424.601, 39115.626, 39125.601, 39335.601

and 39335.636.and 39335.636.

and 39335.636.

On Model 39424.601 it is used to complete 115 volt AC

circuit to Circuit 2 compressor. On Models 39115.626,

39125.601, 39335.601 and 39335.636 it is a furnace

blower relay.

The relay has a 115 volt AC coil.

Terminals 1 and 3 are the coil terminals. When the coil

(terminals 1 and 3) is NOT energized (no power to

terminals 1 and 3), continuity should exist between

terminals 4 to 5; and no continuity between terminals 2

to 4.

When the coil (terminals 1 and 3) is energized (power

to terminals 1 and 3), continuity should exist between

terminals 2 to 4 and no continuity between terminals 4

to 5.

D.D.

Relay, SPST (single pole/single throw) is used onRelay, SPST (single pole/single throw) is used on

Relay, SPST (single pole/single throw) is used on

Models 39115.602, 39115.616 and 39115.626Models 39115.602, 39115.616 and 39115.626

Models 39115.602, 39115.616 and 39115.626.

On these models it is used to complete 115 volt AC

circuits to the compressor and for fan speeds.

The relay has a DC volt coil. To check the relay, first

verify AC volts have been turned off to the unit.

Next, verify the relay coil is NOT energized (no DC power). No

continuity should exist between terminals COM to NO. Ener-

gize the coil with DC volts (10 to 16). Continuity should exist

between terminals COM to NO. If the above checks are

correct, the relay is good – DO NOT replace it. If the previous

checks are not correct, the relay is defective and should be

replaced.

E.E.

Relay, SPDT (single pole/double throw) is used onRelay, SPDT (single pole/double throw) is used on

Relay, SPDT (single pole/double throw) is used on

Models 39115.XXX, 39325.XXX, 39335.XXX andModels 39115.XXX, 39325.XXX, 39335.XXX and

Models 39115.XXX, 39325.XXX, 39335.XXX and

39424.601.39424.601.

39424.601.

On Models 39115.XXX it controls HIGH and LOW FAN

speeds. On Models 39325.XXX, 39335.XXX and

39424.601, it opens the control circuit for the fan motor

when the coil is energized.

NOTE: Incorrect wiring to the thermostat can energize the

relay coil on heat pump models 39325.XXX, 39335.XXX

and 39424.601.

The relay has a DC volt coil. To check the relay, first verify

all AC volts have been turned off to the unit.

Next, remove the wires from COM and NC terminals.

Verify the relay coil is not energized (no DC power).

Continuity should exist between terminals COM and NC

and no continuity between terminals COM and NO. Next,

energize the relay coil with DC volts (10 to 16). Continuity

should exist between terminals COM and NO and no

continuity between COM and NC. If the above checks are

correct, the relay is good – DO NOT replace it. If the above

checks are not correct, the relay is defective and should be

replaced.