Contents For the installer For the user Safety information 3 Description of the appliance 4-5 Technical specifications 13 Unpacking 14 - Damages - Use - Positioning - Protecting the dishwasher against freezing - Spray arm - Coarse filter/microfilter - Fine filter - Detergent dispenser - Rinse aid dispenser - Water softener Installation The control panel - Water inlet - Water drainage - Electrical connection 6 - How to set the delayed start Adjusting the water softener 7 Programme chart 8
Safety information Before installing and first using the dishwasher, read this instruction booklet carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the dishwasher are thoroughly familiar with its operation and safety features. Save these instructions and make sure they remain with the dishwasher if it is moved or sold, so that everyone using it through its life can be properly informed on appliance use and safety.
Description of the appliance 4 5 -4-
Spray arm (1) It is important to keep all the holes in the spray arm clear. A clogged hole can seriously affect washing efficiency. If the spray arm needs cleaning, unscrew the nut anticlockwise, remove the washer and lift off the spray arm. Clear the holes and shake out any food remnants. Coarse filter/microfilter (2) The purpose of the coarse filter is to catch large objects such as toothpicks and pieces of eggshell. Make sure that the filter is always clean. Turn the coarse filter anticlockwise.
The control panel Indicator and control lamps A On/Off button Water softener button Display Delay start button Programme buttons Combination buttons ”A”: In addition to selecting a programme, you can by pressing these two buttons adjust the setting of the water softener and cancel a programme in progress. Indicator lamps: Control lamps: Shows current phase of the selected programme.
Adjusting the water softener To prevent limescaling on the dishes and to the interior of the dishwasher, the dishes must be washed with soft water. Contact your local Water Authority to find the exact water hardness level for your area. This dishwasher is equipped with a water softener, where tapwater which is harder than 4 °d (german degree) is softened. The water softener has 5 settings: Adjust the water softener according to the table below for the water hardness level for your area.
Programme chart All types of dishes Type of dishes Plates and cooking pots Type of soil: • heavily soiled • normally soiled • dried-on food remnants especially eggwhite and starch • dried-on food remnants All types of dishes Coffee cups, delicate items • normally soiled • lightly soiled • 4) Suitable programme: INTENSIVE 70° C Programme cycle: 1) Pre-wash Washing 2 x rinses Final rinse Drying NORMAL 65° C Pre-wash Washing Rinse Final rinse Drying ENERGY SAVE 55° C 3) Pre-wash Washing Rinse F
Loading and unloading the dishwasher How to load the dishes Baskets The illustration shows the dishwasher loaded with six place settings. Your own dishes are not likely to be identical to this load, but if you follow the advice below we are sure you will be pleased with the results. Main basket Cutlery basket The cup shelves can be placed in two different levels. ● Always place glasses, cups and bowls upside down. ● Incline deep dishes (soup plates etc.) so that the water can run off when drying.
Using the appliance Starting the programme Pause function 1. Scrape or rinse off solid food remnants. With the pause function the programme can be interrupted for a short period of time. 2. Load the dishwasher. (See the basket and loading). 1. Press in the On/Off button. The programme stops. 3. Put the correct amount of detergent into the detergent dispenser and close the lid. 2. All lamps goes out. 3. When you want the programme to continue again, you press the On/Off button.
In the event of a fault Before calling out an engineer, please check through the details below because some faults can be rectified easily without the need to call out an engineer. If an engineer is called to resolve a problem listed below or to repair a fault caused by incorrect installation or mis-use a charge will be made, even if the appliance is under guarantee. Fault Check The programme will not start.
In the event of a fault With help of the error code on the display, it’s possible that you can solve the problem yourself. When the problem is solved, press in the button for the disrupted programme and the programme continues. For other error codes on the display ( , followed by a numbers): • Interrupt the dishwashing cycle. • Switch the dishwasher off. • Select the relevant programme again. If the problem occurs again, contact your local service centre, stating the error code.
Information for test centres The salt container and rinse aid dispenser shall be filled in accordance with this instruction manual. Before conducting the measurements the dishwasher shall be operated for one or two complete cycles using detergent and a clean load.
Unpacking Damages If the dishwasher has been damaged during transport, you should immediately notify the company responsible for delivering it. Check that the dishwasher is undamaged. If you discover any damage, faults or that anything is missing, you should notify the dealer immediately. Never leave packaging material in a place where children may play with it.
Installation Water inlet The dishwasher is equipped with safety features which are to prevent the water from going back to the fresh water system. These features are according to current water technical safety regulations. The temperature of the water supply should not exceed 65° C and the pressure should be between 80-1000 kPa (0,8 - 10 bar). It is important to have a tap or stopcock, positioned close to the dishwasher and with easy access.
Technical changes possible Technische Änderungen vorbehalten