CONTENTS CONTENTS 4.6.1 GENERAL & ed eed Symbols used in this manual Using and keeping the manual . Precautions... Control panel Hotplate... Selecting the burner... Electronic ignition hotplate. Manual ignition hotplate. Hotplate flame regulation .. Electronic ignition ova. Manual ignition oven Grill Electronic ignition grill Manual ignition grill. Electric hotplate Cleaning and Maintenance Schedule 10 Abnormal Operation Dimensions of the appliance. Testing (before leaving) Test point... Data plate.
1 GENERAL INFORMATION i GENERAL INFORMATION Id Symbols used In this manual Below are shown tha various symbols used in the manual to highlight particularly important information. The safety symbols draw attention to potential hazards for personal safety, Absolutely respect all safety messages by following these symbols. WARNING Risk of injury or death. ‘WARNING CAUTION To avoid possible injuries and/or malfunctions. CAUTION 1.
2. WARNINGS DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE. DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT 1S IN OPERATION. DO NOT MODIFY THIS APPLIANCE, THIS APPLIANCE SHALL NOT BE USED ASA SPACE HEATER. THE APPLIANCE IS NOT SUITABLE FOR USE IN MARINE CRAFT. Ensure all transit protection is removed prior to installation.
3. USE w USE 1d BI Precautions CAUTION This appliance must only be used by responsible adults. During use and immediately after use the burner and other accessible parts may be hot; do not touch these parts caution and always keep children at 2 safe distance. After using the appliance ensure the doorknobs are off. After use always shut off the gas supply at the main gas tap.
3 USE The following symbols are for burner flame regulation and correspond to the position of the knob, MOTE: Different models could have similar knobs and symbols. & OF all burners a High flame hob and grill Burners B Low flame hob and grill burners 1-2-3-4-5-8 Electric hotplate temperature Lk 180” Tale" “Bo Oven temperature OTHER SYMBOLS Electronic ignition switch Light switch Fan switch Hotplate 3.3.1 Selecting the burner WARNING The flame must never extend beyond the edge of the pan.
3. USE 3.3.2 Electronic ignition WARNING Male sure there are no pans or any other objects on the burners when igniting. ‘WARNING To ignite the burner, gently push in and turn the control knob to position HIGH FLAME and, keeping the knob pushed in, at the same time press the electronic ignition push button. Once the burner is lit, keep the knob pushed in for a few seconds to ensure the flame remains lit.
3 USE 3.4.
3. USE 3.5.1 Electronic ignition grill WARNING Do not ignite the grill burner with the door closed. ‘WARNING To ignite the burner, gently push in and turn the control knob to the HIGH FLAME position and, keeping the knob pushed in, at the same time press the electronic ignition button. Once the burner is lit, keep the knob pushed in for a few seconds to ensure the flame remains lit.
3 USE 3.6 Electric hotplate A CAUTION CAUTION Before turning on the electric hotplate (or if the hotplate has remained unused fora long time) it is necessary to eliminate any moisture by turning on the hotplate and leaving it on for 30 minutes with the corresponding nob In position |. Use pans with flat bottoms and with diameters no less than the diameter of the hotplate, Dry the bottom of the pan before placing it on top of the hotplate.
> CAUTION SON [> CAUTION 3. USE CAUTION Hot surfaces may be damaged on contact with cold water or with a wet cloth. Do not use abrasive, corrosive or chlorine-based products, pot scourers or steel wool, Do not leave acid or alkaline substances (vinegar, salt, lemon juice, act) on the surfaces of the appliance. Stainless steel surfaces and enameled parts must be washed with water and neutral soap or detergent, rinsed and dried.
4, INSTALLATION 4.1 Dimensions of the appliance The overall dimensions are illustrated in FIG. 2 with the cavity diagrams. The overall dimensions include the trivet {pan support}, control knobs, handles and gas connection. 4.2 Fitting cavity WARNING The appliance must fitted at an appropriate and safe distance from flammable materials.
4, INSTALLATION WARNING The appliance is not suitable for connection with a hose assembly. WARNING WARNING A manual shut-off valve shall be provided on the inlet connection of the appliance. The valve shall be accessible for operation and firmly fixed. ‘WARNING Below are the gas characteristics for which the appliance is set (given lase on the appliance data plate).
4, INSTALLATION 4.4 Electric connection Low voltage 12Y ~— This chapter concerns only models marked [2V on the appliance data plate. CAUTION This appliance must be connected to a 12V = source. The circuit must be protected by a fuse of no more than 3 Ampere. FAUSTIAN Ensure that the polarity of the connection Is correct! WARNING Absolutely do not connect the appliance to the mains voltage (230 this would destroy the components and cause a hazard for the user WARNING To connect the appliance use a 1.
4, INSTALLATION 4.6 Testing (before leaving) Ignite all burners both individually and concurrently to ensure correct operation of gas valves, burners and ignition. Turn gas taps to low flame position and observe stability of the flame for each burner individually and concurrently. Ensure correct operation of the flame failure protection and check that the burners do not operate when the lid is down.
4, INSTALLATION SERVICING WARNING The servicing shall be carried out only by authorized personnel. WARNING Deo not modify this appliance. WARNING Before any servicing intervention shut off gas supply, disconnect all the electrical power supplies and remove the appliance. ‘WARNING Hotplate: burners, injectors, thermoplastic and ceramic ignites TMB NAW EW ld Remove trivet {pan support) by pulling up from hotplate. Remove screws from appropriate burner head cap. Remove head cap.
5. SERVICING Gas cocks NEW Remove the control knob by pulling. Remove the maintop assembly. Unscrew gas cock saddle clamp. Rem the underside of the appliance, remove the thermonuclear lead and the gas pipe from the gas cock. Remove the appropriate gas cock clamp by unscrewing the screws, Remove the gas cock from the manifold. Replace/ refit in reverse procedure. Oven thermostat Remove the appropriate control knee by pulling. 1. 2. Remove the maintop assembly. 3. Unscrew gas cock saddle clamp. 3.
WHO TO CONTACT For service and replacement parts, firstly contact your selling agent.