INSTRUCTION for USE ABSORPTION-REFRIGERATOR miniBar RH 400 RH 400 LR RH 302 D RH 402 D English Type H20 / 60 821 2693-31 T.D.
TABLE OF CONTENTS 1.0 INTRODUCTION 3 2.0 FOR YOUR SAFETY 3 3.0 WARRANTY AND CUSTOMER SERVICE 3 4.0 INSTALLATION 4 5.0 2.1 Warnings and Safety Advice 2.2 Coolant 4.1 4.2 4.3 4.4 4.5 4.6 4.7 3 3 The Purpose of this Manual Tools/Materials Required Unpacking Cleaning Installation Securing Connecting the Device to the Electricity Supply 4.8 Changing the Sliding Hinge 4.9 Changing the Doorhang 4.10 Changing the Decor Panel 4 4 4 4 5 6 6 INSTRUCTION FOR USE 10 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.
1.0 INTRODUCTION You have made an excellent choice by choosing the Dometic miniBar. We are convinced that you will be satisfied with your new appliance in every way. Silent in operation, the miniBar fulfils high quality standards and guarantees an efficient use of resources and energy during its entire working life, i.e. during manufacturing, use and disposal. Please study the installation and operating instructions carefully before attempting to operate the miniBar. 2.0 2.
When contacting customer service, please always state model, product, MLC-Code and serial number! You can find this information on the model label inside the device. RH 400 e.g. 4.0 4.1 INSTALLATION The Purpose of this Manual The manual shows you how to: install the miniBar correctly. operate the miniBar correctly. guarantee the miniBar´s correct maintenance and functioning. deal with faults by yourself. 4.
4.5 Installation IMPORTANT: Please follow the installation details below carefully. Guarantee is valid for products installed as described only. 1. The refrigerator must be level both directions 2. There sould be 20mm clearance to the wall 3. Ventilation must be provided as shown in alternatives A,B,C or D 4. The ventilation duct must at least measure 105mm x the wtdth of the refrigerator 5.
4.6 Securing The miniBar must be screwed onto the cupboard using the lower hinges. 1. Tighten screw. 4.7 2. Put on cap. Connecting the Device to the Electricity Supply The device must be connected to a properly earthed socket in line with the relevant valid country regulations. Check prior to initial operation that the voltage noted on the model label corresponds to the mains voltage.
4.8 Changing the Sliding Hinge (RH 400 LR, optional with RH 302 D and RH 402 D) 1. 2. 3. 4. Distance to cupboard door (A) 1. mm A 2. mm 1. When closed, the cupboard door (A) must not lie against the rest of the surrounding cupboard area (distance 1-2mm). 2. There must be a distance of 6-8mm between the cupboard door and the miniBar.
4.9 Changing the Doorhang 1. L R 2. 3. 2. 1. 4. 5. 6. 7. R L 1. 2. 8. 12. 9. 10. 13. 8 11.
4.10 Changing the Decor Panel (optional with RH 400 LR) - Unscrew the 2 screws of the upper door hinge. - Pull the door and the hinge off, away from the housing and in an upward direction from the lower hinge pin (2-3). - Unscrew the screws (4) and pull off the frame section (5). - Pull the decorative panel (6) out of the door frame and push in the new decorative panel (7) in such a way that the upper edge runs exactly parallel to the upper section of the frame.
5.0 5.1 INSTRUCTION FOR USE Initial Operation The device must be plugged into a properly earthed socket. The miniBar achieves its operating temperature after several hours. The miniBar operates silently ! 5.2 Temperature Control 5.3 Automatic Defrost Function The miniBar is fitted with an electronic temperature control with a fixed temperature setting. The first defrosting phase commences 39 hours after the initial operation (5.1) and lasts for two hours.
5.5 Interior Light (only RH 400 LR) When the door is opened, the light in the cooling shelf is switched on via a sensor. Changing bulbs: 1. Pull out the mains plug. 2. Remove the reflector disk. 4. Insert new bulb. 3. Remove the defective bulb. 5.Clip reflector disk back in. Please contact Dometic Service centres for replacement light bulbs.
5.6 5.7 Enviromental Advice miniBars manufactured by Dometic are free from CFCs / HCFCs and fluorinated hydrocarbons. The cooling unit uses ammonia as the coolant (a natural compound of hydrogen and nitrogen). Cyclopentane, which does not damage the ozone layer, is used as propellant for the insulation made from PU-foam. Disposal In order to ensure the re-use of recyclable packaging materials, these must be disposed of using local collection systems.
5.10 Check List Failure : No cooling (the aggregate at the back of the device is cold). Possible Cause Self Help a.) The device plug is not plugged in. a.) Plug in device plug. b.) No voltage in socket. b.) Check building fuse. Authorised Service c.) Defective electronics or sensor feelers. c.) Install new electronics or sensor. d.) Defective heating cartridge. d.) Install new heating cartridge. e.) The device is in its defrosting phase. e.) See operating instruction 5.
5.
5.12 Index Cleaning............................................ 4 Check List..........................................13 Customers Service............................ 3 Coolant..............................................3,12 Data Plate..........................................3 Decor Panel...................................... 9 Defrosting..........................................10 Disposal.............................................5 Doorhang...........................................
Dometic GmbH In der Steinwiese 16 D-57074 Siegen Phone: +49-(0) 271 / 692 0 Fax: +49-(0) 271 / 692 300 www.dometic.
