INSTRUCTION for USE ABSORPTION-REFRIGERATOR RH 430 LD RH 438 LD RH 440 LD RH 441 LD RH 448 LD RH 460 LD RH 461 LD RH 468 LD miniBar RH 436 D RH 438 D RH 447 D RH 448 D RH 468 D RH 455 LD RH 456 LD RH 456 LDE English Type H20 / 60 821 2693 - 61 T.D.
TABLE OF CONTENTS 1.0 INTRODUCTION 3 2.0 FOR YOUR SAFETY 3 3.0 WARRANTY AND CUSTOMER SERVICE 3 4.0 INSTALLATION 4 5.0 2.1 Warnings and Safety Advice 2.2 Coolants 3 3 4.1 4.2 4.3 4.4 4.5 4.6 4.7 The Purpose of this Manual Tools/Materials Required Unpacking Cleaning Installation Securing Connecting the Device to the Electricity Supply 4.8 Changing the Sliding Hinge 4.9 Changing the Doorhang 8 9 INSTRUCTION FOR USE 10 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11 5.
1.0 INTRODUCTION You have made an excellent choice by choosing the Dometic miniBar. We are convinced that you will be satisfied with your new appliance in every way. Silent in operation, the miniBar fulfils high quality standards and guarantees an efficient use of resources and energy during its entire working life, i.e. during manufacturing, use and disposal. Please study the installation and operating instructions carefully before attempting to operate the miniBar. 2.0 2.
.0 4.1 4.2 INSTALLATION The Purpose of this Manual The manual shows you how to: install the miniBar correctly. operate the miniBar correctly. guarantee the miniBar´s correct maintenance and functioning. deal with faults by yourself. Tools / Materials Required You will need the following tools for initial operation: mild detergent 4.3 Unpacking Check during unpacking that the device is defect-free. Report transport damage to the transport company within 48 hours.
4.5 Installation 200 cm² 20 mm IMPORTANT: Please follow the installation details below carefully. Guarantee is valid for products installed as described only. 1. The refrigerator must be level both directions 2. There sould be 20mm clearance to the wall 3. Ventilation must be provided as shown in alternatives A,B,C or D 4. The ventilation duct must at least measure 105mm x the wtdth of the refrigerator 5.
4.6 4.6.1 Securing RH456LD/E 1. Tighten screw. 4.6.2 2. Put on cap. RH430LD, RH440LD, RH441LD, RH460LD, RH461LD RH436D, RH447D, RH438(L)D, RH448(L)D The miniBar must be screwed onto the cupboard using the lower hinges. 1. Tighten screw. 2. Put on cap.
4.7 Connecting the Device to the Electricity Supply The device must be connected to a properly earthed socket in line with the relevant valid country regulations. Check prior to initial operation that the voltage noted on the model label corresponds to the mains voltage.
If the plug supplied on the mains lead is not suitable for the socket in your home, it should be cut off and disposed of safely, or destroyed, to avoid any possible shock hazard resulting from the plug being inserted into a 13 amp socket elswhere in the use. A suitable replacement plug should then be fitted as given above. 4.8 Changing the Sliding Hinge (possible with RH430LD, RH438LD, RH440LD, RH441LD, RH448 LD, RH460LD, RH436D, RH447D) 2. 1. 1. 2. 3. 4. Distance to cupboard door (A) 1. mm A 2.
4.9 Changing the Doorhang ( RH436D, RH447D, RH430LD, RH440LD, RH441LD, RH460LD, RH461LD, RH438LD, RH448LD) L 1. R 2. 3. 2. 1. 4. 5. 6. 7. R L 1. 2. 8. 12. 9. 10. 13. 9 11.
5.0 5.1 INSTRUCTION FOR USE Initial Operation The device must be plugged into a properly earthed socket. The miniBar achieves its operating temperature after several hours. The miniBar operates silently ! 5.2 Temperature Control min. 5.3 The miniBar is fitted with an electronic temperature control. The thermostat control button is situated in the internal containers rear area. (RH455LD, RH456LD/E: the thermostat button is situated in the unrefrigerated compartment). max.
5.5 Automatic Door Control (ADC) The following descriptions only apply to devices with ADC. Using a red dot in the display window (A, point 3), the ADC shows that the miniBar´s door has been opened. 1. Open the miniBar, check its contents and - if applicable- stock it up again. 2. Close the miniBar. RH456LD/E All other models 2. 2. A A 1. 3. Insert ADC key and turn to the right. 1. 3. Insert ADC key and turn to the left. The red dot has disappeared now. 4. Remove ADC key. 5.5.
5.6 5.6.1 Interior Light RH456LD /E Model RH456LD/E is fitted with low voltage lighting. When the door is opened, the light in the cooling shelf is switched on via a sensor. The light in the uncooled storage shelf is switched on manually by means of a switch integrated into the lamp. Changing bulbs: 1. 2. 1. Pull out the mains plug. 2. Remove the reflector disk. 90° 3. Remove the defective bulb. 4. Insert new bulb. 5.Clip reflector disk back in. 5.6.
5.7 5.8 Environmental Advice miniBars manufactured by Dometic GmbH are free from CFCs / HCFCs and fluorinated hydrocarbons. The cooling unit uses ammonia as the coolant (a natural compound of hydrogen and nitrogen). Cyclopentane, which does not damage the ozone layer, is used as propellant for the insulation made from PU-foam. Disposal In order to ensure the re-use of recyclable packaging materials, these must be disposed of using local collection systems.
5.11 Check List Failure : No cooling (the aggregate at the back of the device is cold). Possible Cause Self Help a.) The thermostat is set to 0. a.) Set temperature control to middle position. b.) The device plug is not plugged in. b.) Plug in device plug. c.) No voltage in socket. c.) Check building fuse. Authorised Service d.) Defective electronics or sensor feelers. d.) Install new electronics or sensor. e.) Defective heating cartridge. e.) Install new heating cartridge. f.
5.
Dometic GmbH In der Steinwiese 16 D-57074 Siegen Phone: +49-(0) 271 / 692 0 Fax: +49-(0) 271 / 692 300 www.dometic.de/minibar www.dometic.
