Operation Manual

ManualsBrandsDometic ManualsAbsorption 3 Way Fridges3 Way Fridge & Freezer 90L

RM2350

8251227-05

MO-M 0911

RA/RM-1D

INSTALLATION

OPERATING

INSTRUCTIONS

FOR YOUR SAFETY

If you smell gas:

1. Open windows and door

2. Don’t touch electrical switches.

3. Extinguish any open ame.

4. Turn off the gas supply at the source.

FOR YOUR SAFETY

Do not store or use gasoline or other am-

mable vapors and liquids in the vicinity of

this or any other appliance.

Improper installation, adjustment,

alteration, service or maintenance can

cause injury or property damage. Refer to

this manual. For assistance or additional

information consult a qualied installer,

service agency or the gas supplier.

wARNING

Contact a qualified person.

Summary of content (12 pages)

PAGE 1
INSTALLATION & OPERATING INSTRUCTIONS FOR YOUR SAFETY If you smell gas: 1. Open windows and door. 2. Don’t touch electrical switches. 3. Extinguish any open flame. 4. Turn off the gas supply at the source. 5.. Contact a qualified person. RM2350 FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. ! wARNING 6 Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage.
PAGE 2
contents Introduction We are pleased that you have chosen this refrigerator and hope you will derive much satisfaction from using it. The refrigerator is designed for storage of foods and storage of frozen foods and making ice. The installation and servicing should only be carried out by an authorized/qualified person. It is important to read through these instructions carefully before using the refrigerator.
PAGE 3
InstallatIon InstRuctIons If the lower grille is not at floor level where leaking gas can escape,a 40 mm hole to the outside should be made in the floor of the recess to drain any unburned gas to the outside.Fit the hole with wire mesh and an angled plate to protect it from stones,mud etc. geneRal InfoRMatIon The installation, servicing and gas installation must be performed by an authorised/qualified person.
PAGE 4
- Apply a sealing strip to the foremost floor of the enclosure. The sealing should provide a complete isolation of the appliance’s combustion system from the vehicle interior. dIMensIons The following dimensions offer adequate space for service and proper installation. oveRall dIMensIons mm Recess dIMensIons Height A Width B Depth C Height H Width W Depth D 766 556 577 756 521 542 Note! Be careful not to damage the sealing strip when the refrigerator is put in place.
PAGE 5
The supply pipe should be of copper. If other material is used, it must be of a type approved for use with continuously operating bottle-gas appliances and have threaded connections throughout. All connectors etc. should be of a type specifically designed for the type and diameter of the connection pipe used, and screwed joints should be sealed with a joining compound approved for use with bottle-gas.
PAGE 6
13. Locate the door. Remove plug and latch retainer on the top of the door. Replace in opposite positions. 14. Place door on lower hinge pin. Mount upper hinge pin and fasten it using a socket wrench. 15. Locate top decoration panel and detach the travel catch. Replace in opposite position. 16. Fit top decoration panel and reinstall screws, knobs and seal strips. 17. Check the travel catch to make sure it works properly, that the door closes easily and that the gasket seals well on all sides.
PAGE 7
opeRatIng InstRuctIons contRol panel A absoRptIon RefRIgeRatoR systeM in an absorption refrigerator system, ammonia is liquefied in the finned condenser coil at the top rear of the refrigerator. The liquid ammonia then flows into the evaporator (inside the freezer section) and is exposed to a circulating flow of hydrogen gas, which causes the ammonia to evaporate, creating a cold condition in the freezer.
PAGE 8
The coldest positions in the refrigerator are under the cooling fins and at the bottom of the refrigerator. The warmer areas are on the upper door shelves. This should be considered when placing different types of food in the refrigerator. 12 v dc opeRatIon only operate your refrigerator on 12 V DC when the engine of the vehicle is running - otherwise your battery will soon be discharged. Turn the knob A to the position marked “DC” for 12 V DC operation.
PAGE 9
MaIntenance & seRvIce pRoduct caRe defRostIng Service and maintenance must be done on a regular schedule to keep the refrigerator operating properly, efficiently and safely. The service should only be performed by a qualified electrical or gas technician. 1. Shut off the refrigerator by turning the knob A to “OFF” position. 2. empty the refrigerator, leaving the drip tray under the finned evaporator. ReplacIng the heateR 3. Leave the cabinet and freezer doors open.
PAGE 10
14. Be sure to reconnect the wire to high voltage electrode. Check the electrode for proper location and gap. cleanIng the flue and buRneR Maintenance work should be made by a qualified service man. inspect the flue baffle. it should be reasonably clean and free of soot. Heavy soot formation indicates improper functioning of the burner. The flue and burner both require cleaning in the following manner: Electrode 1/8” to 3/16” (3-5 mm) Burner tube 1.
PAGE 11
Appendix Rearview equipment Heaters Flue baffle 12 volt terminal block Screw for burner cover Burner jet Flexible cord wiring diagram 11
PAGE 12