PS180SolarController-O-NZ.book Seite 1 Montag, 2. Oktober 2017 10:00 10 ENERGY & LIGHTING SUN POWER SC1230-PWM EN 30 A Solar Charge Controller Installation and Operating Manual. . . . . . . .
PS180SolarController-O-NZ.book Seite 3 Montag, 2. Oktober 2017 10:00 10 SC1230-PWM Explanation of symbols Please read this instruction manual carefully before installation and first use, and store it in a safe place. If you pass on the product to another person, hand over this instruction manual along with it. Table of contents 1 Explanation of symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 2 General safety instructions . . . . . . . . . . . . . . . . .
PS180SolarController-O-NZ.book Seite 4 Montag, 2. Oktober 2017 10:00 10 General safety instructions I 2 SC1230-PWM NOTE Supplementary information for operating the product.
PS180SolarController-O-NZ.book Seite 5 Montag, 2. Oktober 2017 10:00 10 SC1230-PWM A General safety instructions NOTICE! • Check the manufacturer‘s data for your battery and ensure that the maximum voltage of the solar charge controller does not exceed the manufacturer‘s recommended charging voltage. • Do not use the solar charge controller to charge non-rechargeable batteries. • Be sure to connect the battery before exposing the solar panel to the sun.
PS180SolarController-O-NZ.book Seite 6 Montag, 2. Oktober 2017 10:00 10 Scope of delivery 2.3 Operating the device safely ! WARNING! A NOTICE! 3 Scope of delivery SC1230-PWM • All lead acid batteries produce harmful and explosive gases. The battery should be mounted in a well ventilated area, as far as possible from any ignition source. Do not smoke when in the vicinity of the battery under charge. • Do not disconnect any cables when the device is still in use.
PS180SolarController-O-NZ.book Seite 7 Montag, 2. Oktober 2017 10:00 10 SC1230-PWM Technical description Solar charge controller The solar charge controller has the following functions: • PWM controlled • Three stage charging (Bulk, Boost/Equalize, Float) • Battery types selectable: Sealed, Gel, and Flooded • LCD display dynamically displaying operating data and working condition • Two USB output ports (maximum output 2.
PS180SolarController-O-NZ.book Seite 8 Montag, 2. Oktober 2017 10:00 10 Technical description 5.1 SC1230-PWM Connecting and operating elements 1 5V Max. 2,4A 1 USB 3 Temp. Sensor 4 No. in fig.
PS180SolarController-O-NZ.book Seite 9 Montag, 2. Oktober 2017 10:00 10 SC1230-PWM 5.2 Technical description Display elements 2 AkWh% V °C °F PV SOC BATT. TYPE LOAD TYPE Source Display PV with menus solar voltage (V), solar current (A), solar power (kWh) Description Day Night No charging Charging BATT. with menus battery voltage (V), battery current (A) battery temperature (°C/°F)) LOAD with menus load current (A), load power (kWh), load mode EN Battery capacity, in charging BATT.
PS180SolarController-O-NZ.book Seite 10 Montag, 2. Oktober 2017 10:00 10 Installing the solar charge controller SC1230-PWM 6 Installing the solar charge controller 6.1 Mounting the solar charge controller When selecting the installation location, note the following: • The device must be installed vertically on a wall. • The device must be installed on a level and sufficiently sturdy surface. • The device must be installed in a location that is protected from moisture.
PS180SolarController-O-NZ.book Seite 11 Montag, 2. Oktober 2017 10:00 10 SC1230-PWM 6.2 Installing the solar charge controller Connecting diagram ! WARNING! • Always observe the following connection sequence. Overvoltage can damage the electronics of the device. – Connecting the solar panel: Connect the battery, then connect the solar panel, finally connect the load. – Disconnecting the solar panel: Disconnect the load, then disconnect the solar panel, finally disconnect the battery.
PS180SolarController-O-NZ.book Seite 12 Montag, 2. Oktober 2017 10:00 10 Installing the solar charge controller SC1230-PWM Key to connecting diagram No. in fig. 4 Description 1 Solar charge controller 2 USB output ports 3 Load 4 Fuse 5 12 Vg/24 Vg battery 6 Fuse 7 Inverter 8 Fuse 9 Solar panel 10 Circuit breaker ➤ Lay all the necessary lines. ➤ Plan the distribution and fuse protection of the circuits carefully.
PS180SolarController-O-NZ.book Seite 13 Montag, 2. Oktober 2017 10:00 10 SC1230-PWM 6.3 ! Installing the solar charge controller Connecting the solar charge controller WARNING! Make sure that all the connection and wiring is conducted by a qualified electrician. Connecting to the battery I NOTE Battery voltage less than 6 V will not be recognised by solar charge controller. Always connect the battery first, in order to allow the solar charge controller to recognize the system voltage.
PS180SolarController-O-NZ.book Seite 14 Montag, 2. Oktober 2017 10:00 10 Using the solar charge controller SC1230-PWM 7 Using the solar charge controller 7.1 Browsing the display The display automatically cycles through the menus. ➤ Press the MENU button to switch from one menu to the next menu. 7.2 Setting the solar charge controller Zero clearing the accumulative power ➤ Press the MENU button until you get to the PV solar power menu. ➤ Press and hold the SET button for 5 s. ✓ The value flashes.
PS180SolarController-O-NZ.book Seite 15 Montag, 2. Oktober 2017 10:00 10 SC1230-PWM Using the solar charge controller No.
PS180SolarController-O-NZ.book Seite 16 Montag, 2. Oktober 2017 10:00 10 Using the solar charge controller 7.3 SC1230-PWM Protective functions of the solar charge controller Protection Conditions Solar module The solar module can be reversed, when the reverse polarity battery is connected correctly. Status The controller is not damaged Battery reverse polarity The battery can be reversed, when the solar module is not connected.
PS180SolarController-O-NZ.book Seite 17 Montag, 2. Oktober 2017 10:00 10 SC1230-PWM 8 Troubleshooting Troubleshooting If you are unable to rectify the fault, get in touch with a specialist workshop. Display Fault Possible cause Suggested remedy The Display is off dur- Solar panel ing daytime when disconnected sunshine falls on solar modules properly. Confirm that solar module wire connections are correct and tight. Wire connection is Battery voltage is Check the voltage of battery.
PS180SolarController-O-NZ.book Seite 18 Montag, 2. Oktober 2017 10:00 10 Warranty 10 SC1230-PWM Warranty The statutory warranty period applies. If the product is defective, please contact the manufacturer's branch in your country (see the back of the instruction manual for the addresses) or your retailer.
PS180SolarController-O-NZ.book Seite 19 Montag, 2. Oktober 2017 10:00 10 SC1230-PWM 12 Technical data Technical data S SC1230-PWM Ref. no.: 9600005819 Nominal system voltage: 12/24 Vg, Auto Battery input voltage range: 9 V to 32 V Rated charge/discharge current: 30 A at 55 °C Max. PV open circuit voltage: 50 V Battery type: Sealed (Default)/Gel/Flooded Equalize charging voltage: Sealed:14.6 V/Gel: No/Flooded:14.8 V Boost charging voltage: Sealed:14.4 V/Gel:14.2 V/Flooded:14.