TDS

DOMINATOR® LG+ TECHNICAL DATA SHEET
CONTACT INFORMATION: Black Diamond Coatings, Inc. 6036 Nature Coast Blvd. Brooksville, FL 34602. USA.
www.BDCbrands.com | 800-270-4050 | [e-mail] Page 2 of 2
© 2022 Black Diamond Coatings, Inc.
All new masonry and concrete surfaces should be allowed 30-90 days to
properly dry/cure in accordance with industry standards. The surface
should be tested for pH levels. Surface pH should not be higher than 10-11.
Surface areas that display a reading of 11 should be etched with a solution
of Muriatic Acid. Retest the pH following etching process to make sure it is
below the recommended level.
SMOOTH TROWLED CONCRETE GARAGES
Follow the Etching Instructions below before sealing.
ETCHING INSTRUCTIONS
To etch the concrete floor, use a mixture of 1-part Muriatic Acid and 3
parts water. Be sure to wear personal protection gear (boots, gloves, and
goggles, etc.), follow the manufacturer’s instructions and safety
precautions when working with Muriatic Acid. Working in sections (10’ X
10’), apply a generous amount of the acid solution with a plastic sprinkling
can and allow the solution to effervesce until it stops reacting. Rinse the
surface thoroughly with a garden hose to not let the acid dry on
the surface.
2. TEST
Perform a small test area (at least 2 sq. ft.) using the product to ensure
suitability and the desired results prior to full application. Test for
application coverage rate. Use the same preparation, equipment and
conditions expected during the entire application. Due to the wide variety
of substrates, preparation methods, application methods and
environments, the customer should test the product in an inconspicuous
spot for penetration and compatibility prior to full application.
3. APPLY
Before use, consult our website to ensure proper application techniques.
Do NOT dilute or alter the product. Shake the DOMINATOR® container prior
to use as some settling may have occurred. Note that this product
prevents water penetration of the surface, generally resulting in a
beading effect. In areas where a slippery condition may occur, we
recommend adding our texture additive, DIAMOND GRIT™ to sealer prior
to application.
Generally, apply two coats of sealer to concrete paver or concrete
surfaces. Ensure smooth application of sealer. If spraying, use even,
broad strokes to avoid streaking. If rolling, keep a wet edge during
application to avoid streaking. Ensure smooth application of sealer at the
coverage rate of 250-400 square feet per gallon per coat with a sprayer
for most even results. If product puddles or drips on the surface, back-roll
to smooth out excess product for even coverage. DO NOT FLOODCOAT. We
recommend waiting an hour between coats if an additional coat is
necessary. The sealer coat should be absorbed prior to applying
subsequent coats. Consider the hardscape surface needs. Conditions
such as surface porosity, temperature and shade can impact the time
needed between coats, in addition to the number of coats necessary to
achieve the desired results. Previously sealed surfaces and extremely
dense surfaces may only require one coat of sealer. Some extremely
dense surfaces may be better suited for DOMINATOR® STONE+ GLOSS if a
color-enhancing, high sheen is desired (e.g., wet cast pavers, some
commercial grade pavers, clay pavers, concrete pavers with shells, some
decorative concrete surfaces). Smooth surfaces may produce a higher
sheen; rougher surfaces will produce a lower sheen. Reference the
Application resources on our website for further instructions.
Allow sufficient dry times. Following complete application, we
recommend at least 24 hours before significant foot traffic, and at least
24-48 hours before any vehicular traffic on freshly sealed surfaces. If a
light rain occurs more than an hour after sealing, then there should not be
any issues.
4. CLEANUP
Place any unused sealer back into original container to store for future
use. Clean equipment thoroughly with a mild detergent and warm water
until free of sealer residue. Sealer will stain clothing but can be removed
from skin with a mild cleaner.
Store and handle properly. Store in a cool, dry place, but do not let the
product freeze; and dispose of properly if it is allowed to freeze. Do not
store at temperature above 90° F.
Please note: Waste from this product is not hazardous as defined under the Resource
Conservation and Recovery Act (RCRA) 40 CFR 261. Incinerate in approved facility. Do
not incinerate closed container. Dispose of in accordance with Federal,
State/Provincial, and Local regulations regarding pollution.
5. MAINTAIN
Remove oil and other fluids from the sealed surface as soon as possible
using a mild cleaning agent. Avoid pressure washing pavers for 45 days
following sealing. Do not use harsh chemicals (e.g., paint thinners,
strippers, solvents) on the sealed areas.
Due to the different tire manufacturers and components used to make
tires we cannot guarantee hot tire resistance.
CUSTOMER CARE
We pride ourselves on being available to assist with product and job-
related questions, including application instructions. Call 800-270-4050
during our regular business hours; or visit our website at
www.BlackDiamondCoatings.com for additional product information.
LIMITED WARRANTY
Black Diamond Coatings, Inc. (BDC) warrants this product to be free of defects when it is
manufactured and shipped. All recommendations, information and technical data are based on the
research of BDC and that of others and are believed to be accurate and reliable. However, the
accuracy and completeness are not guaranteed because we cannot cover every scenario, including
surfaces, conditions and application methods. Where permitted by law, BDC makes no other
warranties with respect to this product, express or implied, including without limitation the implied
warranties of merchantability or fitness for particular purpose. User shall test the product on a small
inconspicuous area to ensure desired results are achieved using the same conditions and
equipment as expected during the entire application. User shall rely on his/her own knowledge and
testing to determine the suitability of the product for a particular purpose and assume all risks and
liability in connection thereto. Acceptance and use of this product absolves BDC from any other
liability, from whatever source, including liability for special, indirect or consequential damages, and
the liability of BDC shall not exceed the price of this product. A proof of purchase will be required for
any claim of a defective product. Replacement of any defective product shall be the buyer’s sole
remedy under this warranty. This warranty may not be modified or extended by representatives of
BDC or its distributors.