USER’S GUIDE TFT LCD-MONITOR Model No : L520BAV http://www.dwe.co.
FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Emission Characteristics Tested by SEMKO A sample of this type has been tested and has shown compliance with theguidelines in the swedish document TCO 99. DECLARATION OF CONFORMITY This product is also designed for IT power system with phase to phase voltage of 230V. We, Manufacturer / Importer DAEWOO ELECTRONICS CO.
CONTENTS Introduction ............................................................................. 1 Product Features ................................................................. 2 Setup ......................................................................................... 3 Installing the Stand .............................................................. 3 Connecting the 15 Pin Signal Cable and Power Cord ......... 4 Connecting the Speakers ......................................................
SETUP PRODUCT FEATURES INSTALLING THE STAND The monitor is designed for use in a small work area or for those who need more work space on the desk. The convenient and user-friendly on-screen display allows for easy and accurate adjustments of screen size, position and screen color. The monitor supports a safe working environment in strict compliance with the TCO 99 standard for low emissions . The monitor complies with the VESA Display Data Channel (DDC) specification for Plug and Play compatibility.
CONNECTING THE SPEAKERS CONNECTING THE 15 PIN SIGNAL CABLE AND POWER CORD 1. Turn off the computer and monitor. 1. Align the two hooks on each speaker with the holes on the right and left side of the monitor and insert the hooks into the holes. 2. Connect the 15 pin signal cable to the output port of the video card in your computer and monitor. 2. Plug the connector of the POWER (DC IN 12V) Jack 1 of the speaker R into the 12V DC(AUDIO POWER) port 2 on the rear of the monitor. 3.
CONNECTING THE OTHERS ABOUT SPEAKER BUTTONS adjusts audio volume. 1. Plug the connector to the S-Video port 1 on the rear of the monitor (ex : VCR, DVD , ---). (up) : increases speaker volume. 1 (down) : decreases speaker volume. 2. Plug the connector to the RCA port 2 on the rear of the monitor (ex : Camcorder, VCR, DVD, ---). 1/2 VOLUME (UP/DOWN) 3 MUTE turns mute function on and off. 2 3 4 POWER turns audio on and off. 3.
OPERATION & ADJUSTMENT CONTROL PANEL KEY PROCESS 1 POWER 2 POWER Indicator MENU shows both normal operation and power management status with power indicator light. swithes the monitor on and off. 2 1024X768 60K UT L TY OSD 1 / UT L TY 75 OSD MENU UT L TY EXIT MENU SHARPNESS EXIT SHARPNESS EXIT 7 3 6 5 4 3 (*) OSD OFF 4 moves cursor to the right or low window in the OSD window and increases the value of any selected function.
ADJUSTMENT PROCEDURE OSD FUNCTIONS WITH USING PC No Is the H.Size proper? INPUT Adjust the CLOCK control. PC Select PC mode. SVIDEO Select S-Video mode. VIDEO Select Video(CVBS) mode. SOUND Adjust sound. Yes Is the noise displayed on the screen? Perform the AUTO POSITION. No Yes Perform the AUTO TRACKING. Is the noise displayed on the screen yet? VOLUME Increase or decrease audio volume. BALANCE Balance audio sound. TREBLE Adjust high frequency response.
Adjust the horizontal & vertical picture image quality and size. AUTO TRACKING COLOR R RED CONTROL Adjust the red color. G GREEN CONTROL B BLUE CONTROL Adjust the blue color. STATUS Display horizontal & vertical frequency and polarity. RECALL Reset the screen to the Factory Preset Display Settings. AUTO POSITION Choose automatically the proper horizontal position and vertical position & size of the screen image. LANGUAGE Select language for OSD (6 languages). Adjust the green color.
SELF DIAGNOSIS HUE Adjust the hues of image. SHARPNESS Adjust the display image quality (if the screen proceed to scaling up). SOUND BALANCE Balance audio sound. TREBLE Adjust high frequency response. BASS Adjust low frequency response. If there is no image, the Self Diagnosis screen will be displayed. Self Diagnosis function checks if the status of the monitor screen is “No Signal”, “Out of range” or “Check Cable”.
SPECIFICATIONS Panel Synchronization Size Pixel Pitch Viewing Angle Contrast Ratio Brightness Color Filter Horizontal Vertical Video Bandwidth Max Resolution(Optimal) Colors Display Area PC Input Signal Sync Video AV Input Signal Video Audio TV Receiving Signal TV Tuner (Option) External Speaker Max. Output Plug and Play Power Source Power Consumption Dimension-W x H x D (without speaker) 15-inch (38 cm) diagonal 0.297 x 0.
FACTORY PRESET TIMINGS CHANGING THE STAND REMOVING THE STAND VESA MODES Mode VGA Resolution (dots X lines) 640 X 480 a 60Hz H.Freq (KHz) V.Freq (Hz) Remark 31.5 60 Non-interlaced 37.9 72 Non-interlaced VGA 640 X 480 a 72Hz 640 X 480 a 75Hz 37.5 75 Non-interlaced SVGA 800 X 600 a 56Hz 35.2 56 Non-interlaced SVGA 800 X 600 a 60Hz 37.9 60 Non-interlaced SVGA 800 X 600 a 72Hz 48.1 72 Non-interlaced SVGA 800 X 600 a 75Hz 46.9 75 Non-interlaced XGA 1024 X 768 a 60Hz 48.
TROUBLESHOOTING REMOVING THE COVER Symptom Check Picture is jitterd. Adjust Clock to set the screen position and adjust Clock fine until a noise isn’t displayed. No picture. Check if power switch and computer power switch are in the on position. Remove the Cover. Check if the signal cable is correctly connected to the video card. Check if the pins of D subconnector are not bent. Check if the computer is in the power- saving mode. ATTACHING THE MONITOR WITH THE ARM-STAND(OPTION) Tighten 4 screws.
APPENDIX DESCRIPTION FOR D-SUB CONNECTOR Symptom No sound. Check Check if the speaker power switch and the audio cable are correctly connected to the computer. Adjust the volume after checking the sound is muted. Check the audio system in the computer. Low sound. Adjust the volume on the OSD Menu and the speaker. Adjust the volume of the sound card in the computer. Dull sound. Adjust Bass and Treble on the OSD Menu. No video.
