USER’S GUIDE TFT LCD-MONITOR Model No : L700C http://www.dwe.co.
FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Emission Characteristics Tested by SEMKO A sample of this type has been tested and has shown compliance with theguidelines in the swedish document TCO 99. DECLARATION OF CONFORMITY This product is also designed for IT power system with phase to phase voltage of 230V. We, Manufacturer / Importer DAEWOO ELECTRONICS CO.
CONTENTS Introduction ............................................................................. 1 Product Features ................................................................. 2 Setup ......................................................................................... 3 Connecting the 15 Pin Signal Cable and Power Cord ......... 3 Operation & Adjustment ...................................................... 4 Specifications ......................................................................
SETUP PRODUCT FEATURES CONNECTING THE 15 PIN SIGNAL CABLE AND POWER CORD The monitor is designed for use in a small work area or for those who need more work space on the desk. 1. Turn off the computer and monitor. The convenient and user-friendly on-screen display allows for easy and accurate adjustments of screen size, position and screen color. 2. Connect the 15 pin signal cable to the output port of the video card in your computer and monitor.
OPERATION & ADJUSTMENT CONTROL PANEL KEY PROCESS 1 POWER 2 POWER Indicator MENU shows both normal operation and power management status with power indicator light. swithes the monitor on and off. 5 4 1280X1024 80K UT L TY 75 UT L TY OSD 3 OSD SELECT UT L TY EXIT SELECT SHARPNESS EXIT SHARPNESS EXIT 8 7 3 (*) 6 2 OSD OFF 1 4 moves cursor to the right or low window in the OSD window and increases the value of any selected function.
ADJUSTMENT PROCEDURE OSD FUNCTIONS ICON CONTROL FUNCTION No Is the H.Size proper? Adjust the CLOCK control. LANGUAGE Select language for OSD (6 languages). CLOCK Adjust the width (horizontal size) of the screen image. CLOCK FINE Sharpen the focus by aligning the illuminated pixels and adjust until the screen image looks focused, crisp and sharp. Adjusting the CLOCK FINE after the CLOCK adjustment will produce a clear screen.
SELF DIAGNOSIS ICON CONTROL FUNCTION OSD TIME OUT Adjust the display OSD Menu. STATUS Display horizontal & vertical frequency and polarity. RECALL Reset the screen to the Factory Preset Display Settings. AUTO POSITION Choose automatically the proper horizontal position and vertical position & size of the screen image. CONTRAST Adjust the contrast of image, the difference between light and dark areas on the screen. If there is no image, the Self Diagnosis screen will be displayed.
SPECIFICATIONS Panel Synchronization Video Bandwidth Max Resolution Colors Display Area PC Input Signal AV Input Signal (Option) Size Pixel Pitch Viewing Angle Contrast Ratio Brightness Color Filter Horizontal Vertical Sync Video Video Audio TV Receiving Signal TV Tuner (Option) External Speaker Max. Output (Option) Plug and Play Power Source Power Consumption Dimension-W x H x D 17-inch (43.2 cm) diagonal 0.264 x 0.
FACTORY PRESET TIMINGS CHANGING THE STAND REMOVING THE STAND VESA MODES Mode VGA Resolution (dots X lines) 640 X 480 a 60Hz H.Freq (KHz) V.Freq (Hz) Remark 31.5 60 Non-interlaced VGA 640 X 480 a 72Hz 37.9 72 Non-interlaced VGA 640 X 480 a 75Hz 37.5 75 Non-interlaced SVGA 800 X 600 a 56Hz 800 X 600 a 60Hz 35.2 56 Non-interlaced 37.9 60 Non-interlaced 48.1 72 Non-interlaced SVGA 800 X 600 a 72Hz 800 X 600 a 75Hz 46.9 75 Non-interlaced XGA 1024 X 768 a 60Hz 48.
TROBLESHOOTING ATTACHING THE MONITOR WITH THE ARM-STAND(OPTION) Symptom Check Picture is jitterd. Adjust Clock to set the screen position and adjust Clock fine until a noise isn’t displayed. No picture. Check if power switch and computer power switch are in the on position. Check if the signal cable is correctly connected to the video card. Tighten 4 screws. Check if the pins of D subconnector are not bent. Check if the computer is in the power- saving mode. Use the VESA approved arm-stand.
APPENDIX DESCRIPTION FOR D-SUB CONNECTOR Pin Signal 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Red Green Blue GND GND GND-Red GND-Green GND-Blue +5Vdc GND-H.Sync GND-V.
