PLASMA DISPLAY USER’S MANUAL D S P - 4 2 2 4 LV S DSP-5014LXS Proper use guarantees product life. Before using the product, be advised that you read this owner’s manual well and try to operate it.
Features • 50” XGA, 42” VGA wide Plasma Panel • DVD Direct Connection / Outstanding Picture Quality Digital Broadcasts Receive DVD can be directly connected to the unit so that you can view clear digital images. You can enjoy even higher quality images. by connecting digital broadcasting receiver with which digital broadcasts can be viewed.
F C C R F I N T E R F E R E N C E S TAT E M E N T NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Safety Precautions Power Always obey all safety messages. • All the safety and operating instructions should be read before the product is operated. If anything strange happens, unplug this product from the wall outlet. • Do not disassemble or replace any parts of the monitor. Refer to a qualified service personnel for repair. During a lightning storm, or when it is left unattended and unused for a long period of time, unplug it from the wall outlet.
While Using Monitor Do not open cover (or back) because high voltage is present within the monitor’s enclosure. Never push objects of any kind into this product through openings at the back of monitor. It may cause electric shock. It may cause fire or electric shock. No objects filled with liquids, such as vases, shall be placed on the monitor. Do not allow children to play or hang on the monitor. Do not place candle or lighted cigarette on the monitor.
Safety Precautions Power Always obey all safety messages. • All the safety and operating instructions should be read before the product is operated. CAUTION You can be injured, or this product or any other your property can be damaged if you don’t follow instructions. When moving your monitor, remove the power plug, antenna, and cables, and be sure to move it by more than two people.. Failure to follow this instruction can result in electric shock or personal injury.
The plasma display panel consists of fine cells. Although the panels are produced with more than 99.9 percent active cells, there may be some cells that do not produce light or remain lit. Do not allow a still picture to be displayed for an extended period, as this can cause a permanent ghost image to remain on the Wide Plasma Display. Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode.
Checking Accessories Note Check to be sure that the following items are packed with your Plasma pannel.
Note Optional Accessories Speakers The following items are optional accessories. Refer purchasing optional accessories from Daewoo Electronics Local Dealer or the dealer from where you purchased the unit. DP-SP50 / DP-SP50U - Speaker Main Unit Dimension : 110(W) x 738(H) x 86(D)mm - Including Speaker Stand Dimension : 210(W) x 836(H) x 210(D)mm - Audio Amplifier : 10W + 10W - Impedance : 8Ω - Weight : 4.1kg DP-SP55 / DP-SP55U - Speaker Main Unit Dimension : 100(W) x 628(H) x 88.
CONTENTS PREPARATION 4 • Safety Precautions 12 • Panel Controls 13 • Remote control CONNECTION 14 • 16 • 18 • 20 • 22 • 24 • 26 • 28 • Watching Digital Broadcasts Watching Cable Broadcasts Watching Satellite Broadcasts Watching a DVD Image Watching a VCR Image Watching a Camcorder/Game Console Image Connecting PC(15pin D-sub) Connecting PC(DVI) APPLICATION 31 • 32 • 34 • 36 • 38 • 40 • 41 • 42 • 44 • 46 • 47 • 49 • 51 • Selecting Auto Picture Mode Customizing Picture Adjusting Screen Size Adjusting Scr
Panel Controls Front Panel, Back Panel, Remote Control having same names in Plasma Display and Remote Control would function in exactly the * Parts same way. Front Power STAND BY/OPERATE • Power control sensor • Power Standby: Red - Standby Green - ON • Power button Select when adjusting volume or select/adjust “MENU.” Press when moving “MENU.
Remote Control Note • Use two “AAA” batteries. • Be sure to use replacement batteries of the same type as the original ones. • The life of a battery depends on how much it has been used. ) indicates the page in which * The number in ( the function of each button is explained in detail. INPUT SELECT Input Select button POWER Power button 44 Used to select a desired input.
Watching Digital Broadcasts Watching Digital Broadcasts • To watch digital broadcasts: - Purchase a separate digital Broadcasting Receiver(SET-TOP BOX) - Connect the PDP to a Digital Broadcasting Receiver as shown below. 1 Connect a Digital Broadcasting Receiver to the PDP • Prepare A/V Cables supplied. • Connect the cables from the Digital TV Receiver output terminal to the PDP(Component 1, 2) input terminal. • When connecting the cables, be sure to match the cable colors.
3 Input Select INPUT SELECT • Select [Component 1 or Component 2] by pressing the INPUT SELECT button of the Remote Control or the PDP unit. • Each time you press the INPUT SELECT button, different input modes appear. The sequence is as follows: Component 1 --> Component 2 --> Video 1 --> Video 2 --> PC -->DVI. Component1 DVI 4 Component2 PC Video1 Video2 Select a Desired Channel and Function • Select a desired channel and function by using the Remote Control of Digital Broadcasting Receiver.
Watching Cable Broadcasts Watching Cable Broadcasts • To watch cable broadcasts, subscribe to your local Cable TV Broadcasting, and then, connect a cable Broadcasting Receiver TV to the PDP as shown below. 1 Connect a Cable Broadcasting Receiver to the PDP. • Prepare the A/V cable. • Connect the receiver(Output) to PDP(Video Input) as shown below. • When connecting to an external AV source, be sure to match the colors.
3 Input Select INPUT SELECT • Select [Video 1 or Video 2] by pressing the INPUT SELECT button of the Remote Control or the PDP unit. • Each time you press the INPUT SELECT button, different input modes appear. The sequence is as follows: Video 1 --> Video 2 --> PC --> DVI --> Component 1 --> Component 2. 4 Video1 Video2 PC Component2 Component1 DVI Select a Desired Channel and Function • Select a desired channel and function by using the Remote Control of the Cable Broadcasting Receiver.
Watching Satellite Broadcasts Watching Satellite Broadcasts • To watch satellite broadcasting, subscribe to a Digital Satellite Broadcasting, then connect setellite Broadcasting Receiver to the PDP as shown below. 1 Connect a Satellite Broadcasting Receiver to the PDP. • Prepare the A/V cable. • Connect the receiver(Output) to PDP(Video Input) as shown below. • When connecting to an external AV source, You have to connect to the same color AV source. S-VIDEO Comp.
3 Input Select INPUT SELECT • Select [Video 1 or Video 2] by pressing the INPUT SELECT button of the Remote Control or PDP unit. • Each time you press INPUT SELECT button, a different input mode appears. The sequence is as follows: Video 1 --> Video 2 --> PC --> DVI --> Component 1 --> Component 2. 4 Video1 Video2 PC Component2 Component1 DVI Select a Desired Channel and Function • Select a desired channel and function by using the Remote Control of the Satellite Broadcasting Receiver.
Watching a DVD Image Watching a DVD Image • Component Input is set to 480i and 480p mode. • Connect the cable from the DVD Video Output (Y, Pb/Cb, Pr/Cr) to the Component Input at the back of PDP, and connect the cable from DVD Audio output (Left, Right) to the Audio Input at the back of PDP. 1 Connect a DVD Player to the PDP. • Prepare the AV cable. • Connect the DVD(Output) to the PDP(Component or Video Input) as shown below. • When connecting to an external AV source, match the colors.
3 Input Select INPUT SELECT • Select [Component 1 or Component 2, Video1, Video2] by pressing the INPUT SELECT button of the Remote Control or the PDP unit. • Each time you press the INPUT SELECT button, a different input mode appears. The sequence is as follows: Component 1 --> Component 2 --> Video 1 --> Video 2 --> PC --> DVI. Component1 DVI 4 Component2 PC Video1 Video2 Select a Desired Title and Function • Select a desired title and function by using the Remote Control of the DVD.
Watching a VCR Image Watching a VCR Image 1 Connect a VCR to the PDP. • Prepare the AV cable. • Connect the Video(Output) to PDP(Video Input) as shown below. • Video can use either the video terminal or the S-video terminal. S-VIDEO Comp. VIDEO L- AUDIO -R VIDEO INPUT S-Video Video/Audio VCR 2 22 Press the Power Buttons • Turn the PDP and the VCR ON.
3 Input Select INPUT SELECT • Select [Video 1 or Video 2] by pressing the INPUT SELECT button of Remote Control or PDP unit. • Each time you press the INPUT SELECT button, a different input mode appears. The sequence is as follows: Video 1 --> Video 2 --> PC --> DVI --> Component 1 --> Component 2. 4 Video1 Video2 PC Component2 Component1 DVI Select a Desired Title and Function • Select a desired title and function by using the Remote Control of the VCR.
Watching a Camcorder/Game Console Image Watching a Camcorder/Game Console Image • Enjoy images recorded by camcorder or the game console after connecting to the PDP. 1 Connect a Camcorder/Game Console to the PDP. • Prepare the AV cable. • Connect the Video(Output) to the PDP(Video Input) as shown below. • When connecting to an external AV source, match the colors. S-VIDEO Comp.
3 Input Select INPUT SELECT • Select [Video 1 or Video 2] by pressing the INPUT SELECT button of the Remote Control or the PDP unit. • Each time you press the INPUT SELECT button, a different input mode appears. The sequence is as follows: Video 1 --> Video 2 --> PC --> DVI --> Component 1 --> Component 2. 4 Video1 Video2 PC Component2 Component1 DVI Select Function • Select the Function by using the Remote Control of Camcorder or Game Console.
Connecting PC(15pin D-sub) Connecting PC • DAEWOO PLASMA supports resolution of VGA, SVGA, XGA, SXGA, UXGA. • Before connecting a PC to the PDP, be sure to adjust the resolution of PC. 1 Before connecting to the PDP, set the resolution of the PC. • Go to SETUP-CONTROL PANEL-DISPLAY PROPERTIES in Window Screen. • Choose the SETTINGS tab in the DISPLAY Menu. • In the SETTINGS Menu, select (50” : 1024 x 768), (42” : 640 x 480 or 800 x 600). 2 Connect the PC to the PDP.
3 Press the Power button. • Turn on the PDP and the PC. 4 Input Select INPUT SELECT PC Video2 5 • Select [PC] by pressing the INPUT SELECT button of the Remote Control or PDP unit. • Each time you press the INPUT SELECT button, a different input mode appears. The sequence is as follows: PC --> DVI --> Component 1 --> Component 2 -->Video 1 -->Video 2. DVI Video1 Component1 Component2 Enjoy Dynamic Ultra Screen Monitor by Using PC’s Keyboard or Mouse.
Connecting PC(DVI) Connecting PC • DAEWOO PLASMA supports resolution of VGA, SVGA, XGA, SXGA, UXGA. • Before connecting a PC to the PDP, be sure to adjust the resolution of PC. • This product is not supported by Plug and Play, so select Standard Monitor when setting PC monitor. 1 Before connecting to the PDP, set the resolution of the PC. • Go to SETUP-CONTROL PANEL-DISPLAY PROPERTIES in Window Screen. • Choose the SETTINGS tab in the DISPLAY Menu.
3 Press the Power button. • Turn on the PDP and the PC. 4 Input Select INPUT SELECT DVI PC 5 • Select [DVI] by pressing the INPUT SELECT button of the Remote Control or PDP unit. • Each time you press the INPUT SELECT button, a different input mode appears. The sequence is as follows: DVI --> Component 1 --> Component 2 --> Video 1 -->Video 2 -->PC. Component1 Video2 Component2 Video1 Enjoy Dynamic Ultra Screen Monitor by Using PC’s Keyboard or Mouse.
PC and DVI Input Resolution Available in PDP • According to the kind of graphic card, there is no picture of pc input and some problems like line noises can happen in picture. If these problems happen, ask to a graphic card company. Resolution 640x350 640x400 640x480 720x400 720x480 720x576 800x600 832x624 1024x768 1152x864 1152x900 1280x720 1280x960 1280x1024 1600x1200 30 Horizontal Frequency(KHz) Vertical Frequency(Hz) 31.469 37.861 24.823 30.48 31.469 37.861 31.469 35 37.861 37.5 39.375 43.
Selecting Picture Mode 1 Selecting Picture Mode Selecting Picture Mode • Press the [PICTURE MODE] on the Remote Control. • Pressing the [PICTURE MODE] first time will display the current PICTURE MODE. • Select the Picture modes that are appropriately set depending on the kinds of pictures, and enjoy them. PICTURE MODE 2 Each Press of the Button Will Select One of Four Picture Modes. • Each time you press the button, a different Picture mode appears.
Customizing Picture Customizing Picture 1 Press the MENU Button. • The MENU shown below will display on the screen. MENU • You can adjust the color tone and brightness to your preference. Picture Mode Sound Brightness Normal Screen Contrast Utility Color Input Tint Sharpness Color Temp. INPUT SELECT 2 VOL DISPLAY ZOOM- Previous Select Move POWER Press the / Normal Button. • After selecting [Picture] by the / buttons, press the button that will display the following.
4 Select User Mode Adjustments • While you are in [Picture Mode – User], press the select a specific adjustment item. VOL VOL Picture Mode Sound Brightness Screen Contrast Utility Color Input Tint / buttons to User Sharpness Normal Color Temp. Previous Adjust Move 5 Picture Condition Adjustments VOL • Press the / preference. VOL buttons to adjust the picture at your Picture Mode Sound Brightness Screen Contrast Utility Color Input Tint User Sharpness Color Temp.
Adjusting Screen Size 1 Adjusting Screen Size • You can adjust screen size or aspect ratio as desired. Press the SCREEN MODE Button. • Each time you press the SCREEN MODE button on the Remote Control, a different SCREEN MODE appears. The sequence used is as follows: • The MENU shown below will display on the screen.
1 Press the MENU Button. Adjusting from MENU Screen • Press the [MENU] button on the Remote Control. MENU Picture Mode Normal Sound Brightness Screen Contrast Utility Color Input Available Mode Input Tint PC,DVI None • Available Screen Mode Sharpness Component 16:9, Normal Normal Color Temp. (480p or above) Previous Select Move Video 1 16:9, Video 2 Panorama Component Normal (480i) 2 Select “Screen”.
Adjusting Screen Position and Size Adjusting Screen Position and Size 1 Press the MENU Button. • The MENU screen as shown below will appear. MENU • You can adjust the screen position and size as desired. • This function is only used when adjusting the screen position and size on the PDP monitor by using the PC or DVI input signal. INPUT SELECT Picture Mode Normal Sound Brightness Screen Contrast Utility Sharpness Input Color Temp.
3 Press the Volume / VOL Buttons. • Press the Volume / buttons to select “Screen”. • While you are in ‘Screen’ mode, press the or button to select a desired item, and then, adjust the value by pressing the or . VOL Picture H. Size Sound V. Size Screen H. Position Utility V. Position Input Phase Frequency Move Previous Adjust NOTES: 1) Horizontal/Vertical size and position values can be adjusted only in the [PC] or [DVI] input mode. 2) H.
Enlarging Screen Size 1 Enlarging Screen Size • You can view enlarged size of the screen with this function INPUT SELECT Press the ‘ZOOM+’ Button. ZOOM+ • Press the ‘ZOOM+’ button to show currently selected screen size. • Each time you press the ‘ZOOM+’ button, the screen size will increase stepwise in 0 ~ 20 scale. • To reduce the screen size, press the [ZOOM-] button.
2 Move the Screen Position. VOL • While you are in the ‘Zoom’ mode, press the / , / buttons to move screen stepwise up/down, left/right, respectively. VOL Zoom Level 6 NOTES: 1) When the screen is enlarged, the pixel of the screen can become thick and dim. 2) When only subtitle of zoom level remains, you can scroll the image. If subtitle of zoom level disappears, press zoom key, and scroll the image. 3) You can enlarge the screen on freeze mode.
Watching a Still Image 1 Watching a Still Image • You can view still images temporarily with this function. However, displaying the same images such as still images for a long time may cause image sticking. Press the ‘FREEZE’ Button. • If you wish to freeze a picture, press the ‘FREEZE’ button. You can still hear the sound. • Press FREEZE button to cancel the ‘FREEZE’ function. • To view the enlarged images, press the [ZOOM+] button. FREEZE Freeze INPUT SELECT POWER 2 Move the Screen Position.
Adjusting Auto Sound Mode 1 Select SOUND Mode. • Press the [SOUND MODE] on the Remote Control. • Press of the [SOUND MODE] for the first time will display the current SOUND MODE. SOUND MODE 2 Adjusting Auto Sound Mode • Enjoy various sound modes by selecting your favorite Sound Mode depending on the kinds of moving pictures. Every Press of the Button Changes Modes. INPUT SELECT POWER • Each time you press the button, a different sound mode appears.
Customizing Sound Mode Customizing Sound Mode 1 Press the MENU Button. • The MENU Screen as below will be displayed. MENU • This feature allows the user at adjust at his preference. Picture Mode Sound Brightness Normal Screen Contrast Utility Color Input Tint Sharpness Color Temp. Previous Select Move INPUT SELECT Normal POWER 2 Press the / Button. • Select [Sound] by the / buttons, then press the button to display the following.
4 Select the Spatial Effect Mode. • Select Spatial Effect by pressing the / buttons, then select ON/OFF by pressing the button. • Spatial Effect: Used to feel grotesque by emphasizing stereo effect. VOL VOL Picture Balance Sound Spatial Effect On Screen Sound Mode Normal Utility Input Previous Adjust Move 5 Select the Sound Mode. VOL • Select the Sound Mode by pressing the adjust it by pressing the / buttons.
Selecting INPUT SIGNAL INPUT SIGNAL • Used to select INPUT signal of external device connected to the PDP. INPUT SELECT 1 Press the INPUT SELECT Button. INPUT SELECT • Press the [INPUT SELECT] button on the Remote Control or the PDP Display to select desired input signal. • Each time you press the [input select] button, a different screen mode appears.
1 Press the MENU Button. Adjusting from the MENU Screen • Press the [MENU] button on the Remote Control. MENU Picture Mode Normal Sound Brightness Screen Contrast Utility Color Input Tint Sharpness Normal Color Temp. Previous Select Move 2 Select Input. • Select [Input] by the / button. Picture PC DVI Component 1 (DTV/DVD) Component 2 (DTV/DVD) Video 1 Video 2 Sound VOL VOL Screen Utility Input Previous Select Move 3 Select Input Signal.
Checking the Current Input Signal Checking the Current Input Signal • Used to check the INPUT signal mode, resolution, frequency, etc. of the current screen. INPUT SELECT 1 Press the DISPLAY Button. • Press the [DISPLAY] button on the Remote Control. DISPLAY Component 1 1920 x 1080 60 Hz POWER 1. If you watch Digital Broadcasts: Component 1 1920 x 1080 60 Hz DISPLAY ZOOM- Displays which input terminal is used, and indicates the input signal mode.
Selecting MENU Background Screen and Language 1 Press the MENU Button. Selecting Languages • The MENU screen will be displayed as below. MENU Picture Mode Sound Brightness Screen Contrast Utility Color Input Tint Normal • Used to select transparency of the background screen and language used in MENU. Sharpness Normal Color Temp. Previous Select Move 2 Press the / Button. • Select [Utility] by the VOL VOL / button.
Selecting MENU Background Screen and Languages INPUT SELECT POWER 4 Select MENU LANGUAGE SELECT by the Button. VOL / • Select LANGUAGE by the / button. • Every press of the button while you are in the [LANGUAGE] mode would cycle through the different languages.
Selecting Image Sticking Minimization 1 Press the MENU Button. ISM • The MENU screen will be displayed as below. MENU Picture Mode Sound Brightness Screen Contrast Utility Color Input Tint Normal • Image sticking minimization. • Displaying a still image like PC input for a long time causes part image sticking in the panel • The ISM function minimize this effect. Sharpness Normal Color Temp. Previous Select Move 2 Press the / Button. • Select [Utility] by the VOL VOL / button.
Selecting Image Sticking Minimization INPUT SELECT POWER 4 Select Functions. VOL • Every press of the button after select function by the / button would switch between ON/OFF. VOL Picture Pixel Shift Off Sound Low Bright Off Screen Image Invert Off Utility Input DISPLAY ZOOM+ ZOOM- Move MENU VOL Previous Adjust VOL NOTES: * Pixel Shift : The whole screen shifts up/down, left/right at 10sec interval to minimize image sticking.
Setting Sleep Timer 1 Press the SLEEP Button. SLEEP • Press the [SLEEP] button on the Remote Control. • Pressing the [SLEEP] button first time will display the current setting for SLEEP TIMER. • To cancel the SLEEP TIMER, press the [SLEEP] button to select ‘OFF’. Setting Sleep Timer • SLEEP TIMER turns the Monitor off after a preset time.
Before Requesting Service Before requesting for a service, check the following points once again. St y o mm ps • Remote control does not function properly. • The Display makes a snapping sound. • There are empty spots at the top and the bottom area of the screen. C h e c k s • Check for any obstacle between the Remote Control and the Display. • Check for dead batteries and incorrect battery orientation. • Check if the Remote Control is the right one. • Check if the pictures and sound are normal.
In the event that the product has been submerged in the water in rainy season: Immediately wash it with clean water, and dry it in ashadow place, then call for service from the nearest Daewoo Service Center. Never plug the Power Cord since there is risk of electric shock and damag of the product.
