Operating Instructions

N2 Wireless Controller 2.4G
Operating Instructions
This product is a 2.4G wireless handle that supports the
control interface of XBONE/XSX console, and realizes the
game operation of RF 2.4G wireless handle on XBONE/XSX
console. In addition, it can be used in PC/P3 host. On the
PC host, the functions of 4 analog axes, 2 analog keys and
16 digital keys, Big, Small, LT, RT Vibration, Turbo, Marco
and Remap can be switched according to the specifications
of x-input/d-input.N2 2.4G handle.
1: This product consists of 1 Dongle terminal +1 Remote
terminal +1 data cable. When in use, the Dongle terminal and
the Remote terminal are used together, and the data cable is
mainly used for charging.
2: The Dongle terminal provides a two-color connection status
light to display the connection status between dongle and
Remote and an XB key to simulate the XB function of N2 2.4G
handle.
3: The 3：Remote terminal provides four Player LED to display
the player status and POWER status. Two analog keys LT and RT
are provided. There are four analog axes LX, LY, RX and RY. 16
digit keys A B X Y Up Down Left Right LB Rb L3 R3 XB Menu
View Share are provided. One Reset key Reset is provided.
4: The LT RT analog key at the 4:Remote terminal is a variable
resistor output.
5: The 5:Remote terminal provides vibration function, and two
motors, large and small, make vibration response.
6: The 6:Remote terminal provides the Turbo Key function, and
provides one Turbo key to set the Turbo function. There are 8
buttons (A B X Y LB RB LT RT) that can be added with the Turbo
function.
After the Turbo function is enabled, the default output
frequency is 5 beats per second. Press the Turbo key +UP key to
adjust the output frequency of the Turbo to 10 beats per
second. Press and hold the Turbo key+the key to be clear to
clear the single Turbo function.
7: The 7:Remote terminal provides Marco/Remap function. Two
marcos are provided to set Marco/Remap function, and the
default values are marcol = y and marcor = x. Press
MarcoL/R+View to enter the Reamp setting.
At this time, turn on LED3 and LED4, and press MarcoL/R after
the key setting, that is, the setting is completed. Press
MarcoL/R+Menu to enter Marco setting, at this time, LED1/LED2
lights up, and then press MarcoL/R after the key setting, that is,
the setting is completed.
Press View+Menu for 3 seconds, and the motor will shake to
restore its original function.
1: connect with XB ONE/XSX host, plug the USB on Dongle into
the USB port on the host, at this time, the LED light on Dongle
will flash slowly in red and yellow, press the kbkey on Remote,
and the LED1-LED4 on remote will flash slowly.
In the connection mode, when the LED lights on the Dongle end
are red and yellow and the LED lights on the Remote end are
long, the pairing is successful. You can enter the host for game
operation.
2: Connect to the PC host, plug the USB on the Dongle into the
USB port on the PC, and then the LED on the Dongle will flash
slowly in yellow. Press the KBkey on the Remote side, and the
LED on the Remote side will flash slowly, and enter the
connection mode. When the LED on the Dongle side is long in
yellow and the LED on the remote side is long in LED
1/LED1-LED4 (different PC system versions have different handle
lighting modes), it indicates that the pairing is successful.
Playing games on PC requires installing ""Steam"" game
simulator on PC to play games. Tips: Because XB ONE games are
3D games, which need a lot of memory, it is recommended to
use high configuration PC and WIN8 or above system, so as not
to affect the pleasure of playing games.
3: Connect with P3 host, plug the USB on Dongle into the USB
port on the host. At this time, the LED on Dongle will flash
slowly in red. Press the KBkey on the Remote side, and the
LED1-LED4 on the Remote side will flash slowly. Enter the
connection mode. When the LED on Dongle and LED1 on the
remote side are on long in red, it means that the pairing is
successful. You can enter the host for game operation.
4: The battery status display at the 4：Remote terminal shows
that when the voltage is greater than 3.5V during use, the LED
will be on for a long time. When the voltage is equal to
3.5V-3.4V, the low voltage prompts and the LED flashes. When
the voltage is less than 3.4V, the handle sleeps. During charging,
if in use, the charging indicator LED flashes slowly. If it is sleep
state, the LED is in breathing light state (dimming/dimming).
The full LED stays on.
5: In connection with any host, if there is no action for more
than 5 minutes, the Remote terminal will automatically sleep,
and press the KB key of the Remote terminal to wake up, and
the Remote terminal and Dongle terminal will automatically
connect back.
6: When in use, press L3+R3+KB key, and the Remote terminal is
turned off.
I. Product specifications
II. Connection description
Right Rocker
Turbo key
英文
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could
void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The device can be used in
portable exposure condition without restriction.