Operation Manual

Step1.Putthecontrollerflatonthesurfaceofthecontroller.
Step2.PressSelect-hometoentercalibrationmode.ThewhiteLEDofthecontrollerisquicklyblinkedandcalibratedandthe
calibrationiscompleted.Whenthelightgoesoff,thebuttonisreleased.
*Ifthecalibrationfails,thewhiteLEDlightsup.Atthispoint,pressthehomebuttontwice,thecontrollerreturnstothenormal
state,thenshutsdownandreadjustsinstep2.
Correcting:
Ifthecontrollerisabnormal,pressthebutton(pinhole)behindthecontrollercanbereset.
Reset:
1.Lowbatteryalert:theLEDflashesslowlyandindicatesthatthecontrollerneedstobecharged.Ifthevoltagefallsbelow3.6V,the
controllershutsdown.
2.Ifthecontrollerworks,theindicatorflashesslowlyduringcharging.Whenfullycharged,theindicatorlightisalwayson.
3.Ifthecontrollerisoff,theLEDflasheswhiteduringchargingandtheLEDisturnedoffwhenfullycharged.
LEDIndicatorchargestatus:
Ifyouwanttoclearthefunctionoftheprogrammedbutton,pressthesetbuttonfor5seconds,andthelightreturnsfromthe
blinkingtotheoriginaldisplay,NLandNRThefunctionoftheloggedbuttonwascleared.
Clearprogrammingfeatures
1.SetthesingleactionbuttonandpresstheNa(NL/NR)buttonyouwanttoassign.TheLEDflashingstopsnotifyingtheprogram-
ming.
*PresstheNLbuttonafterpressingthe"a"button.TheNLbuttonhasthesamefunctionasthe"a"button.
2.Setthecombinedactionbutton(upto30buttons)andpresstheNL/NRbutton.TheLEDflashingstopsnotifyingtheprogram-
ming.
*Press4differentbuttons(thebuttonsequenceisa+b+x+y),andthenpresstheNRbutton.TheNRbuttonhasthefunctionofthe
sameas(buttonsequenceisa+b+x+y)button.
*Pressthesamebutton("B")8timesandpresstheNLbutton.TheNLbuttonisthesameaspressingeighttimesthefunctioneffect
ofthe"B"button.
*Pressintervaltimeisstoredduringthebuttoninputprocess.
Pressandholdthesetbuttonfor3seconds,andtheindicatorflashes,indicatingthatthecontrollerisinprogrammode.
Enterprogrammode
Programbutton:(NL/NR/SET)
Actionbutton:crossbutton(up,down,leftandright),ABXY,LB\RB\LT\RT\L3\R3
Programmingfunction:
Bluetoothconnection： PresstheLB+HomebuttontoturnonandturnintoIOSBluetoothpairing.Theyellowindicatorlight
flashesandturnsBluetoothonyourIOSdeviceorMacOSdevice,andthenlocatedualshock4wirelesscontroller.Whenpairing
succeeds,theyellowlightofthecontrolleralwaysturnson.
*Supportgames: Minecraft、ChronoTrigger、GenshinImpact、MetalSlug
IOSconnection：
*Battlearena:KingofKings
*Chickensimulator:theThreeKingdoms,thebattlefield,thecombatofGiants:Dinosaur3D.
*Supportgames:Deadcell,mineKraft,Seoulnight、DarkWilderness2、Don'tStarveBeach、Oceanhorn,etc.
Bluetoothconnection： Pressy+hometostartinAndroidpairingmode,flashingredindicatorlights,turnBluetoothonyour
Androiddevice,find"gamepad",andclickandpair.Whenpairingsucceeds,theredlightofthecontrolleralwaysturnson.
Androidconnection：
Bluetoothconnection：Ifthecontrollerisoff,pressandholdtherb+homebuttonfor3secondstoenterthepairingmode,open
theBluetoothsearchinterfaceonthePC,findtheBluetoothname"xboxwirelesscontroller",andclick"OK"afterpairing.If
successful,theblueindicatoronthecontrollerwillalwaysbeon.
PC360connection：
*SupportSteamgames：AncientLegends、FarmersDynasty、Interstellaradventurer、Torchlight3,etc.
Bluetoothconnection： Whenthecontrolleristurnedoff,pressthehomebuttonfor3secondstoenterthepairingmode,openthe
BluetoothsearchinterfaceonthePC,findtheBluetoothnameprocontroller,clickthepairing,andthepairingissuccessfulThered
LEDofthecontrolleralwaysturnson.
PCconnection：
*Ifyoucannotreconnect,thecontrolleristurnedoffafter15seconds.
Links:pressthehomebuttontoconnecttotheconsole.
Afterenablingthedatalineoptionoftheprocontrollerontheswitch,inserttheswitchintotheswitchbaseandconnectthe
controllerthroughthedataline.Afterpullingoutthedataline,thecontrollerwillautomaticallyconnecttotheswitch.The
controllerisautomaticallyconnectedtotheswitchhostviaBluetooth.
Datacableconnection:
1.Click"controllers"fromthehomescreenandselect"changgrip/orde"toenterthepairingscreen.
*Note:usejoycon,touchorpairedcontrollers.
2.Pressandholdthehomebuttononthecontrollerfor3seconds,andtheblueindicatorflashes.
3.Iftheconnectionissuccessful,theblueindicatorontheswitchwilllightup.
4.Iftheconnectionfails,thecontrollerwillshutdownafter60seconds.
Press when you are ready
A
4321
Change Grip/Order
Controllers
Controllers
A OK
Bluetoothconnection:
Switchconnection：
Connectionmethod：