Quick Start Guide

Setup
Wireless Air Conduc�on Headphones
CGS-B6
QUICK START GUIDE
Send your Amazon Order ID to
[e-mail]
You can also scan this QR to access our email address.
“CG ChanGeek” is a registered trademark owned by Changeek Limited.
Other trade marks and trade names are those of their respective owners.
Changeek Ltd. All rights reserved.
SEND US ORDER# for
12-MONTH EXTRA WARRANTY!
背面1， 背面2，背面3
正面1， 正面2，正面3
双面单色印刷，铜版纸157g，三折，展开120*225mm，折后120*75mm
Bluetooth 5.0
Open-ear design for safety, efficiency and health
Long lasting battery
Hands-free control
Clear microphone
Ultra lightweight & Ultra comfortable
Air Conduction Headphones CGS-B6
Setup
Air Conduction Headphones CGS-B6
How to Use?
Air Conduction Headphones CGS-B6
1. Charge
Remarks: USB charger is not included, you can use any of the USB charger
(Output should be no less than 200mA).
Use the supplied Micro-USB cable to connect the CGS-B6 (B6) to USB charger
or USB port on computers.
2. Connect to Device
3. Multifunction Button (MFB)
2.1 Press and hold the Power Button for 3 seconds to turn on the B6, the LED will be
blue / red blinking alternately and you’ll hear the voice prompt “Pairing”.
LED
LED Color / Status Battery Level
Red / Blinking low battery
in chargingRed / Solid
Blue / Solid fully charged
Fig. 1
Fig. 2 Chart. 1
Chart. 2
What’s in the Box?
Air Conduction Headphones CGS-B6
Air Conduction Headphones CGS-B6
Specifications
Air Conduction Headphones CGS-B6
2.2 Unlock your device and go to Settings>Bluetooth page, enable the Bluetooth and
choose “ChanGeek B6” in the “OTHER DEVICES” list. Then you’ll get the B6 be connected
and hear the prompt tone.
MFB
+ / - Button
MFB
Action
Press & hold for 3s
Press & hold for 5s
Press & hold for 2s
2 Short press
Press & hold for 2s
Press & hold for 2s when
phone call is answered
Short press
Short press
Power on
Power off
Answer phone call
End up phone call
Reject phone call
Activate Siri / Google Assistant
Dial last number
Switch phone call from B6 to
phone
Prompt Tone
“Pairing”
Single-tone
Single-tone
Multi-tone
Ringtong (5s) then read
incoming phone No.
-
-
-
Use the Multifunction Button to power on /
off, answer / reject / end up phone call.
It provides great hands-free convenience for
you.
See Chart 2 for more details.
4. + / - Buttons
Use the +/- Button to control the volume and switch tracks.
See Chart 3 for more details.
5. Connect to the 2nd Device
6. Remarks:
B6 allows you to connect 2 devices. Please kindly follow the steps below:
5.1 Connect to the 1st device. (See Paragraph 2)
5.2 Disable Bluetooth function on 1st device, then B6 will enter pairing mode.
5.3 Enable Bluetooth function on 2nd device and choose ChanGeek B6 in “OTHER
DEVICES” list to get B6 sucessfully connected.
5.4 Enable Bluetooth function on 1st device and B6 will connect to the 1st device
automatically.
6.1 When the battery is nearly drained, you’ll hear the voice prompt “low battery”, it
will power off in few minutes. Please kindly charge it.
6.2 If no device is connected to B6, it will power off in 5 minutes for power saving.
6.3 When B6 is power on and near to the device which is connected before, it will build the
connection automatically. “Forget” it from the device in bluetooth page will eliminate
the auto connection.
How to Use?
Air Conduction Headphones CGS-B6
Chart. 3
+ / - Buttons
Action
Press “+” button
Press “-” button
Volume Up
Volume Down
Prompt Tone
Prompt for max. limits
Prompt for min. limits
Long press “+” buttonSkip to next track -
Long press “-” buttonSkip to previous track -
Air Conduction Headphones (CGS-B6) Charging Cable Manual
Model No.
Product Name
Speaker
Frequencey Range
Speaker Sensitivity
Mic Sensitivity
Bluetooth Version
Bluetooth Protocol
CGS-B6
Air Conduction Headphones
Air Conduction Speaker
20-20000Hz
100±5 dB
-40±3dB
Bluetooth V5.0
A2DP, AVRCP, HSP, HFP
Transmition Dist.
Battery Capacity
Playback Time
Standby Time
Full Charge Time
Weight
33FT / 10M
120mAh, 3.7V
6-8H
300H / 12 Days
1.5H
18g
Brand C. G ChanGeek
Origin China
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference,and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:
.
Reorient or relocate the receiving antenna.
.
Increase the separation between the equipment and receiver.
.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
.
Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device
can be used in portable exposure condition without restriction
FCC Statement