Specifications
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
DoorKing Plug-In Vehicle
Loop DetectorSingle or Dual Channel
For Reverse (Safety) & Exit Loops
All DoorKing gate operators are designed with "ports" for our
plug-in loop detectors(DoorKing gate operators only). This
simplifies installation and wiring. Both single channel and two
channel detectors are available. Loops and loop detectors should
be used on all gate operator installations to prevent the gate from
closing on vehicular traffic. 2 year limited warranty
DK9409-010
Two Channel
Plug-in
Loop Detector
Viking Loop Rack & Plug-In
24V Vehicle Loop Detectors
For Reverse (Safety) & Exit Loops
This Loop Rack and Detector system are exclusively
used with the Viking Access System Operators.
VIKLR
VIKDSP-40S
Loop Rack
For Plug-in
Loop Detectors
Plug-in
Loop Detector
Wt. 2 lbs.
EDILMA-1150-HV
EDILMA-1150-LV
EDILMA-1800
EDILMA-1500-LP
EDI LMA-1150 “DEFLECTOMETER” Series
Enclosure / Box Type with Harness
EDI LMA-1500 “DEFLECTOMETER” Series
Plug-in Type Vehicle Loop Detectors
Single channel with programmable single relay output. The DEFLECTOMETER™ display
helps optimize the proper sensitivity setting to detect all vehicles including motorcycles.
NO MORE GUESS WORK WHEN SETTING SENSITIVITY! Wt. 0.75 lb. The LMA-1150
Series offer two models to handle any input power requirement:
LMA-1150-LV(12Vdc, 24Vdc, & 24Vac) / LMA-1150-HV (120Vac to 240Vac)
120 / 240V AC (High Voltage) Loop
Detector with Harness (Fail Safe)
12 / 24V AC/DC (Low Voltage) Loop
Detector with Harness (Fail Safe)
Plug Compatible with the following Operators:
* Chamberlain/Elite SL3000, CSW200
* Advanced Access Automation CSL2000, CSW2000,
RSW1000
* All-O-Matic SL100-DC, SL 150DC, OH 200DC, SW 300DC,
SW350DC
* Intelligate Systems IQ500, IQ5000
* Linear (OSCO) SL & SW Series with APeX controller
* SECOM Late model operators with 10-pin Molex connectors
* Viking Access Models L-3, F-1, T-21, H-10, B-12, Q-4
12VDC / 24V AC/DC
(Low Voltage)
(Fail Safe or Fail Secure Configuration)
12VDC / 24V AC/DC
(Low Power Consumption )
(Fail Safe or Fail Secure Configuration)
The EDI Model LMA-1800 operates on 12 VDC,
24 VDC, and 24 VAC. The detector is designed to
handle gate, parking, drive-through, and all access
control applications where solid-state outputs are
required for both the “detect and “fail” outputs.
Wt. 0.25 lb.
The EDI Model LMA-1500-LP operates on 12VDC,
24 VDC, and 24 VAC, and is designed for low
power requirements. The detector is designed to
handle gate, parking, drive-through, and all access
control applications where solid-state outputs are
required for both the “detect and “fail” outputs.
Wt. 0.25 lb.
DK9410-010
Single Channel
Plug-in
Loop Detector
Diablo Control Vehicle Loop Detector
Solar 12/24 Volt, 9V-220V & 117V AC
For Reverse (Safety) & Exit Loops with Harness
A new low power "Fail-safe" vehicle detector that is perfect for solar pow-
ered safety loop installations. It is the low power version of our DSP-7 de-
tector. It beats all competition for low current consumption. Less than 1mA
without a vehicle and approximately 23mA with a car on the loop. Like the
DSP-7, it operates on any voltage from 10 to 30 volts AC or DC.
LOOPDETSOLAR
10-30 VAC/VDC
Wt. 2 lbs.
The DSP-10 vehicle detector can be used on entrance loops, safety
loops, or free exit loops. Dual relay outputs, extension, delay, pulse on
exit or entrance and the flexibility to be either "fail safe" / "fail secure".
LOOPDET
10-30 AC/DC - Wt. 2 lbs.
LOOPDET117V
117 Volts AC - Wt. 2 lbs.
ELITE™ Plug-in Vehicle
Loop Detector For Reverse (Safety)
Center, & Exit Loops
With Elite's proven design and integration technology, these component detectors will
make installation and maintenance of loop detection systems simple. They are for use
with the Elite commercial gate operators for Exit Loop, Center Loop, and Safety Loop,
depending on the machine and application. Wt. 1 lb.
ELD
LiftMaster™ Plug-in Vehicle
Loop Detector For Reverse (Safety)
Center, & Exit Loops
LMLOOPDETLM
LiftMaster plug-in loop detector includes 8 sensitivity set-
tings, boost, for CSL24V, CSW24V, and LA 500 operators.
* Convenient plug-in design with finger grips.
* No cross-talk between LOOPDETLM
loop detectors.
* 8 sensitivity settings.
* Boost switch for high-profile vehicles.
* 4 frequency options.
* Low power draw.
* Compatible with LiftMaster® gate operators
having expansion boards and Security+2.0
radio technology.
2-1/8” H. x 3/4” W. x 2” D. - Wt. 0.15 lb.
Access Gate Controls & Accessories
17-15