Owner`s manual

9210-065-H-2-13
35
WAR
N
I
N
G
MO
V
ING
GAT
E
C
A
N
C
A
U
S
E
O
p
er
a
t
e
gat
e
on
l
y wh
e
n
g
at
e
ar
e
a
i
s
in
sig
h
t
an
d
f
r
ee
o
f
p
e
op
le
a
n
d
o
b
s
t
r
u
c
t
io
n
s.
D
o
n
o
t
allo
w
c
h
i
l
d
r
e
n
t
o
p
l
ay
in
gat
e
ar
e
a
o
r
o
pe
r
at
e
g
at
e
.
D
o
no
t
st
an
d
i
n
ga
t
e
pat
h
o
r
wa
l
k
t
h
r
o
u
g
h
p
at
h
w
h
ile
g
at
e
i
s
m
ovin
g
.
R
ead
o
w
n
er
’s
m
an
u
al
an
d
sa
f
et
y
in
st
r
uct
i
on
s
.
SE
R
I
O
U
S I
N
J
U
RY OR
D
E
AT
H
C
L
A
S
S
C
E
R
TIF
I
ED TO
C
A
N/
C
S
A
C
22
.
2
NO.
2
47
C
ONFOR
M
S
TO
A
NSI
/
U
L-
3
25
V
E
HIC
U
L
A
R
G
AT
E
OP
ER
AT
OR
HP
53
382
MODE
L
S
E
RI
AL
V
OL
TS
P
H
A
S
E
A
M
P
S
6
0
H
z
M
A
X
GA
T
E LO
A
D
D
o
o
rKi
n
g
, I
n
c
.,
Ing
le
wo
o
d
, C
A
EXIT
LOOP
LMT
REVERSE
LOOP
REV SENSE
CLOSE
6.3 Manual Gate Operation
Caution: Never attempt to manually operate any gate until you have verified that power to the operator has been shut-off.
Unlock Manual Crank
Access Panel
Cuts off AC power to the operator.
Manual Crank
9235, 9245
Mechanical Disc
Brake
The disc brake MUST be manually
released (disengaged) with a slotted
screwdriver (Not provided) before
manually operating the gate.
Disc brake will automatically
reengage after power has been
restored.
R
E
S
E
T
EXIT
LOOP
LMT
REVERSE
LOOP
REV SENSE
CLOSE
1
2
4
3
1
2
4
3
1
2
4
3
Manual Crank
Access Panel
Insert the supplied manual hand crank into the
access hole until it engages with the motor shaft.
Turn the crank to open the gate. 9235, 9245
mechanical disc brake model operators
MUST also have the disc brake
manually released before
manually cranking the
hand crank (See
below).
Motor
Shaft
Manual
crank in
stored
position.
Turn manual release
1/4 turn clockwise
to release the
disc brake.
MANUAL
RELEASE
R
E
S
E
T
R
E
L
E
A
S
E
M
AN
UAL
RE
L
EAS
E
R
E
S
E
T
R
E
L
E
A
S
E
1
2
1
2
5
6
11
13A
13B
13E
25
16
17
L1 L2
L3
B-
B+
M
od
e
EP
M
0 0 0
S
CM
s
er
i
es
bas
ic
I/O control
1
ft/s
.
5
ft/s
0
ft/s
2
ft/s
1.
5
ft/s
Disc
Brake
Access
Panel