Kaba access manager 92 30 Technical Manual 04045376 - 05/2016 EN
Kaba AG Access & Workforce Management Hofwisenstrasse 24 8153 Rümlang Switzerland Kaba AG Access & Workforce Management Mühlebühlstrasse 23 8620 Wetzikon Switzerland Kaba GmbH Access & Workforce Management Albertistraße 3 78056 Villingen-Schwenningen Germany Phone +41 44 818 93 11 www.kaba.com Phone +41 44 931 61 11 www.kaba.com Phone +49 7720 603 0 www.kaba.com This document must not be reproduced in any way or otherwise further used without the written consent of Kaba AG.
Technical Manual Table of Contents Table of Contents 1 2 3 4 About this Document ............................................................................................................................. 7 1.1 Validity............................................................................................................................................................................... 7 1.2 Target group .......................................................................................
Table of Contents Technical Manual 4.2.5 5 6 4 Function of the outputs ............................................................................................................................. 27 4.3 Access control with B-Client AC30 ........................................................................................................................ 28 4.3.1 Operating states .......................................................................................................................
Technical Manual Table of Contents 6.4.1 6.4.2 6.4.3 6.4.4 6.4.5 6.4.6 6.4.7 6.4.8 7 Login ................................................................................................................................................................. 73 Basic structure ............................................................................................................................................... 73 Overview of the service functions........................................................
Table of Contents 6 Technical Manual 04045376 - 05/2016 Kaba access manager 92 30
Technical Manual About this Document 1 About this Document 1.1 Validity This document describes the product: Product name: Kaba access manager 92 30 Item number 04079230 Terminal software: B-Client AC30 from version 669-01-X-K00 Manufacturing date: Starting from March 2016 This document describes all device versions and optional equipment and functions. Options need to be paid for and are therefore only available if they have been purchased.
About this Document 1.4 Technical Manual Orientation in the document This document contains the following orientation aids to facilitate finding of specific topics: 1.5 • The table of contents at the beginning of the manual gives an overview of all topics. • The header always contains the respective main chapter. • Cross references always indicate the number of the chapter in which the supplementary information can be found. Example [ 5.7].
Technical Manual 1.6 About this Document Warnings Warnings containing information/instructions and prohibitions to prevent injury to persons and damage to property are specially labeled. Please pay attention to warnings. They are intended to help prevent accidents and avoid damage. 1.6.1 Hazard Categories Warnings are split into the following categories: CAUTION Slight Risk Describes a potentially hazardous situation that could result in minor physical injuries.
Grouped safety messages 2 Technical Manual Grouped safety messages This product has been built in accordance with state-of-the-art standards and the recognized safety rules. Nevertheless, its use may constitute a risk to persons and cause damage to material property. Read and observe the following safety instructions before using the product. 2.1 Use as directed The product is only intended for use as described in chapter “Product description”.
Technical Manual 2.5 Grouped safety messages ESD (electrostatic discharge) protective measures NOTICE Danger for electronic components due to electrostatic discharge. Improper handling of printed circuit boards or components can cause damages that lead to complete failures or sporadic errors. 2.6 • During installation and repair of the product, the ESD protective measures must be considered. • Wear an ESD wristband when handling electronic components.
Product Description Technical Manual 3 Product Description 3.1 Overview The Kaba access manager 92 30 is designed specifically for control of an individual door (access/exit). The access manager can also be used for the decentralized access control applications. This is why the device is installed in secure indoor locations near the access. The device is designed for direct mounting on the wall. However, it can also be mounted in suspended ceilings, wall recesses etc.
Technical Manual 3.2 Product Description Device variants The Kaba access manager 92 30 is available in two device variants: The difference is in the possible reader connection. One variant allows connection of 2 RFID registration units or readers/subterminals via RS-485. The other variant allows connection of 2 readers via Wiegand.
Product Description 3.3 Technical Manual B-Client AC30 terminal software B-Client AC30 is a terminal software for access control. This terminal software makes the device compatible with the data records used in previous access controls of the B-Net series. 3.3.1 Areas of application Access control The access manager uses various test criteria to check whether a booking made on a reader/subterminal is authorized or not.
Technical Manual 3.3.3 Product Description Supported readers/subterminals The access manager (RFID device variant) supports max. 2 readers/subterminals.
Product Description 3.3.5 Technical Manual Registration units Two registration units can be connected to the access manager via coaxial cables (connections Ant. A and Ant. B).
Technical Manual 3.4 Technical Data 3.4.1 Power supply Product Description For power supply of the device, there are the following alternative options: • PoE (Power over Ethernet) • External 24 V DC power supply unit PoE (Power over Ethernet) Power supply via the 8-wire Ethernet cable (max. 100 m). • Acc. to IEEE 802.3af (12.95 W) and IEEE802.3at (25.5 W). 24 V DC input Power supply via the 24 V DC input using an external power supply unit.
Product Description 3.4.3 Technical Manual Outputs 3 relay outputs • 3.4.4 OUT1: Switches one of the following power sources to the terminal (can be selected via jumper): – 12 V DC – 24 V DC (external device power supply) – External relay voltage (can be fed in via the terminals) • OUT2 + OUT3: Potential-free change-over contact • Contact rating: 30 V AC/DC; 2 A max.
Technical Manual 3.4.5 Product Description Interfaces Ethernet interface • IEEE802.3 compatible 10BASE-T/100BASE-TX Auto sensing, Auto MDIX.
Product Description 3.4.7 3.4.8 3.4.9 Technical Manual Ambient conditions • Ingress protection according to IEC 60529: IP40 • Relative humidity: 5% to 85%, non-condensing • Ambient temperature: – 0 °C – +50 °C (operation) – -20 °C – +65 °C (storage) Dimensions/Weight • Length: 208 mm • Width: 208 mm • Depth: 48 mm • Weight: approx. 0.
Technical Manual 3.5 Product Description Conformity This product conforms to the following standards: EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 EN 300 330-1 V1.7.1 EN 300 330-2 V1.5.1 EN 301 489-1 V1.9.2 EN 301 489-3 V1.6.1 EN 55022:2010, Class B EN 55024:2010 according to the regulations of the EC Directive 1999/5/EC R&TTE Directive The original Declaration of Conformity can be downloaded from www.kaba.com/conformity in PDF format.
Product Description Technical Manual IC Industry Canada Radio Standards Specifications RSS-GEN Issue 4, Sections 8.8, 8.9 and 8.10 and RSS-210 Issue 8, Section A2.6 (Category I Equipment) IC:11038A-KAM9230K5 ICES-003 This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. Canada RSS-GEN 8.4 This device complies with Industry Canada’s licence-exempt RSSs.
Technical Manual Design and function 4 Design and function 4.1 Opening the housing NOTICE Danger for electronic components due to electrostatic discharge. Improper handling can damage or destroy electrostatically sensitive components on printed circuit boards (PCB). • General ESD protective measures must be observed and applied. Remove the housing cover in the following way: 1. Remove two screws M3x8 (TORX 8) on the device bottom side. 2.
Design and function 4.
Technical Manual 4.2.1 Design and function Typical applications The Kaba access manager 92 30 is designed for control of one or maximum two accesses with a total of 2 readers. The following overview shows the three typical applications. The terminal software offers basically the possibility to configure further sub-variants.
Design and function 4.2.2 Technical Manual Superior system Communication with the superior system (host computer) takes place via the Ethernet network. The superior system serves for centralized management of authorizations, access and room profiles, system configuration and alarm management. 4.2.3 Reader The data collection of identification data is performed via external readers. Up to 2 readers can be connected. The readers which are supported depend on the device variant.
Technical Manual 4.2.4 Design and function Function of the inputs The function of the inputs depends on the configuration. The following functionalities are possible: Door frame contact With a door frame contact, the access manager is able to detect if and how long the door is open. If the maximum allowed door-opening time has elapsed and the door is still open, the access manager sends an alarm record to the host computer. A relay can be activated additionally.
Design and function Technical Manual 4.3 Access control with B-Client AC30 4.3.1 Operating states The access manager allows the following operating states: • Online • Fast online • Offline • Autonomous 4.3.1.1 Online The “Online” operating mode is recommended if the arising data records must be permanently available in the host computer. After a booking, the access manager carries out the programmed checks and writes the test result as an error ID into the registration record.
Technical Manual Design and function 4.3.1.5 Overview of the most important differences of the operating modes Proceeding The host decides whether a booking is valid The access manager decides whether a booking is valid Transmission of the registration records Online Fast Online Offline Autonomous X (X)1 (X)2 (X)1.
Design and function 4.3.
Technical Manual 4.3.3 Design and function Examples of door surveillance time sequences 4.3.3.1 Normal sequence with pass through control 4.3.3.2 Door is not opened after release (extended access control) 4.3.3.3 No pass through (extended access control) 4.3.3.
Design and function Technical Manual 4.3.3.5 Door open too long 4.3.3.6 Time exceeded access with door handle 4.3.3.7 Bolt monitoring, normal sequence 4.3.3.
Technical Manual Design and function 4.3.3.9 Bolt monitoring, bolt position time exceeded when locking 4.3.3.10 Bolt monitoring, bolt position time exceeded when unlocking 4.3.3.11 Bolt monitoring, bolt position time exceeded when locking – after door has not been opened 4.3.3.
Design and function 4.4 Technical Manual Light emitting diodes The housing front contains 4 light emitting diodes for status display. Icon 34 Designation Signal Meaning Ethernet yellow Data transfer is active Off No data transfer Device status See chapter 4.4.1 no function - - Power green Device power supply is stable red Load of the device power supply is within the limits. Application of further load leads to the switch-off due to overload.
Technical Manual 4.4.1 Design and function Device status The status of the device is indicated by the LED with the following icon. Status LED The signal sequences and their meaning depend on the terminal software used. 4.4.1.1 B-Client AC30 terminal software The B-Client AC30 terminal software signals different states and sequences via the State LED as follows.
Installation Technical Manual 5 Installation 5.1 Installation conditions 5.1.1 General An accurate installation of all components is a basic requirement for a properly functioning device. The following installation instructions must be adhered to. 5.1.2 Installation site The access manager is installed near the access. The device is designed for the direct mounting on the wall. Depending on the conditions, the device can also be mounted in suspended ceilings, wall recesses etc.
Technical Manual 5.1.4 Installation Cable entry The installation lines can be routed to the device from behind, from the side, from above and below. There are holes in the bottom part of the housing, on the sides and on the top and bottom; they can be removed if necessary, The lines are routed in a duct in the lower part of the rear side, there is the gland to the connections on the front side. NOTICE Ensure sufficient line lengths on the installation site.
Installation Technical Manual 5.2 Installation diagram 5.2.1 Access control with registration unit Example: • Access control with RFID registration units • PoE power supply of the access manager Method for feeding in the power supply via the PSE (Power Sourcing Equipment): 38 – End span (direct supply, e.g. via PoE switch) – Midspan (supply via intermediate sources, e.g.
Technical Manual 5.2.
Installation 5.2.3 Technical Manual Access control with readers via Wiegand Example: • Access control with external readers via Wiegand interface • PoE power supply of the access manager Method for feeding in the power supply via the PSE (Power Sourcing Equipment): 40 – End span (direct supply, e.g. via PoE switch) – Midspan (supply via intermediate sources, e.g.
Technical Manual 5.3 Installation lines 5.3.1 Ethernet Installation Network cable with RJ45 plug, Line requirement: CAT.5 E or higher quality. 5.3.2 Power supply of the reader For short distances of up to 20 meters max., a single cable may be used for the power supply for the reader and data line. A separate power supply cable needs to be provided for longer distances. Recommended cable: 1 x 2 x 0.6 mm or 1 x 2 x AWG 24.
Installation 5.4 Technical Manual Wall mounting When feeding the cable from the side, top or below, first, provide holes for the entry of the installation lines. Not necessary for cable entry from the rear. The housing is mounted directly to the wall using screws/dowels. There are three oval fastening holes for fastening in the housing. Fastening material (included in the delivery): • 4 round-head wood screws DIN 96, diam. 4.
Technical Manual 5.5 Installation Cable routing The installation lines are guided through an opening on the bottom side of the device from the rear side to the front side of the device. The cable passage and the internal cover have eyelets for fastening of installation lines by means of cable ties (not included in the scope of delivery). For the network cable, there is a routing duct on the inner cover.
Installation 5.6 Technical Manual Setting the PoE switches Depending on the power supply type, the PoE switch must be set as described below. Power supply Standard/Power Switch position PoE IEEE 802.3af (12.95 W) PoE PoE+ IEEE802.3at (25.5 W) PoE+ External 24 V DC power supply unit 12-60 W PoE+ In case of power supply via an external power supply unit, the switch position PoE+ is required to prevent the access manager from limiting the power for external consumers.
Technical Manual Installation 5.7 Connections 5.7.1 Network connection Establishing the network connection Plug in the network cable into the Ethernet receptacle (1) and fasten it in the gland on the cover. If the power supply is correct, the Power LED (2) lights up in green after a short time. Once the network connection has been established, the Ethernet LED (3) is flashing in yellow.
Installation 5.7.2 Technical Manual Overview of terminals The following terminals are located in the connection area of the device. Depending on the device variant, the terminals RFID or Wiegand 1+2 are not available.
Technical Manual 5.7.3 Installation External 24 V DC power supply As an alternative to the PoE power supply, the access manager can also be supplied via an external 24 V DC power supply unit. The connection of the external power supply is performed at terminal 24 V EXT. The PoE switch [} 5.6] must be set to "PoE+" position in this case. Use only power supply units that fulfill the requirements of EN 60950-1 as limited power source.
Installation 5.7.4 Technical Manual Registration units Up to 2 registration units can be connected. The registration units A + B are connected by means of the coaxial cable to the RFID input terminal. Example: Connection of Kaba registration unit 90 01/90 02. 48 Connection designation Assignment Ant.
Technical Manual 5.7.5 Installation Readers via RS-485 The RS-485 interface serves for communication with readers. The RS-485 interface (connections A, B, C) is operated in 2-wire mode. For this connection, you may choose a star topology or a bus topology. In case of star wiring, an additional support point terminal needs to be provided to allow parallel distribution of RS-485.
Installation Technical Manual 5.7.5.4 Bus termination Below the RS-485 terminal, there is a jumper for setting the RS-485 terminating resistor. The selection of the terminating resistors depends on the connection architecture. Bus with one root The first device of the bus (access manager 92 30) and the last device of the bus (reader 8) need a 120-ohm terminating resistor. Bus with two roots The last device of the first root and the last device of the second root need a 120ohm terminating resistor.
Technical Manual Installation In readers, the terminating resistor can be set by means of a DIP switch. 5.7.5.5 RS-485 LEDs Three light emitting diodes are located below the RS-485 terminal. They indicate the states of the RS-485 interface.
Installation 5.7.6 Technical Manual Readers via Wiegand Two readers can be connected to the access manager via the Wiegand interface. Example: Reader connection via Wiegand with 5 V and 12 V power supply from the access manager.
Technical Manual 5.7.7 Installation Inputs The access manager has 4 inputs IN1 to IN4. Function of the inputs The inputs are used for the inquiry of sensors such as door-opener key, door handle contact, door frame contact, bolt contact, vandal contact, pass-through contact (e.g., turnstile, light barrier), etc. The function of the individual outputs depends on the settings of the terminal software. Principle The inputs (IN1-IN4) are connected to GND using a simple switch or relay contact.
Installation Technical Manual 5.7.7.2 Non-line-monitored inputs Example: Connection to door frame contact not line-monitored. Tampering to lines between access manager and door frame contact is not detected. 5.7.7.3 Line-monitored inputs With line monitoring activated, resistors (680 Ω, 0.25 W, 2 %) must be connected in series and in parallel to the respective contact. The resistors must be attached in a vandal secure manner directly to the external contact.
Technical Manual Installation 5.7.7.
Installation Technical Manual 5.7.7.5 Status display Above the terminal for the inputs, there are light emitting diodes for status display of the inputs. The current status of the inputs is indicated by a red and green LED respectively as follows.
Technical Manual 5.7.8 Installation Outputs The access manager has 3 relay outputs OUT1 to OUT3. Contact rating: 30 V AC/DC; 2 A max. The outputs can be used for the activation of motor locks, door openers, turnstile drives, technical alarm day/night, security alarm day/night etc. The function of the individual outputs depends on the settings of the terminal software. The wiring of the output OUT1 can be adjusted via jumper (1).
Installation Technical Manual 5.7.8.1 OUT1 as potential-free switching contact By setting the jumper with the designation CD, the OUT1 output can be used similarly to the outputs OUT2 and OUT3 as potential-free switching contact. Principle of output wiring Jumper position IMPORTANT: Only the CD jumper may be set. All other jumpers may not be set. 5.7.8.2 Switching 12 V DC to OUT1 By setting the jumper with designation 12 V DC, the internal 12 V DC power supply is switched to the OUT1 output.
Technical Manual Installation 5.7.8.3 Switching the external DC power supply to OUT1 By setting the jumper pair with designation VREL, a DC power supply connected via the VREL terminal (max. 30 V DC, 2 A) is switched to the OUT1 output. This variant can be used both with device power supply via PoE and device power supply via an external 24 V DC power supply unit. Principle of output wiring Jumper position IMPORTANT: Only the jumper pair VREL may be set. All other jumpers may not be set. 5.7.8.
Installation Technical Manual 5.7.8.5 Principle of output wiring OUT1 The jumper pairs 1 - 3 are used to select the power supply which is switched directly to the consumer via the relay output OUT1. The power supply is protected by a fuse. By setting the jumper 4 (designation CD), OUT1 can also be used as a potential-free switching contact.
Technical Manual Installation 5.7.8.6 Examples Example 1 Connection of a door opener with 24 V DC power supply to OUT1. Only jumper pair 2 is set. All other jumpers may not be set. Example 2 Potential-free control of a digital input via OUT1. Only jumper 4 is set. All other jumpers may not be set.
Installation Technical Manual 5.7.8.7 Connecting door openers Closed-circuit door-openers and open-circuit door-openers can be used. For door openers that are supplied with DC voltage, a diode (a freewheeling diode) must be connected in parallel to the door opener to suppress interference. In doing so, make sure that the diode is connected in reverse-bias direction and check the polarity of the connected voltage.
Technical Manual Installation 5.7.8.8 Status display Below the terminals for the outputs, there are light emitting diodes for status display of the outputs. The current status of the outputs is indicated as follows.
Installation 5.7.9 Technical Manual Standard assignment of inputs/outputs (B-Client AC30) The following assignment for the inputs and outputs has been preset for the BClient AC30 terminal software [} 5.7.10.3]. The assignment of the functions can be adjusted in the b_client_ac30.ini configuration file. Details on the configuration can be found in the B-Client AC30 reference manual. 5.7.9.1 Inputs The following functions are assigned by default to the inputs by the terminal software.
Technical Manual 5.7.10 Installation Configuration-dependent assignment (B-Client AC30) The B-Client AC30 terminal software provides 6 default configurations which can be assigned via a door management parameter. The configuration 2 (door-opener with 1 subterminal and 1 door-opener key) is the preset default upon delivery. Below, 5 configurations are listed which can be used due to a limited number of inputs and outputs of Kaba access manager 92 30.
Installation Technical Manual 5.7.10.4 Configuration 3: Door with 2 subterminals and contact mat, barrier, etc. B A Access 1 Door frame contact IN1 Barrier IN2 Bolt contact IN3 Door opener relay BO1 Alarm relay BO2 GID/DID Subt. A 00/01 GID/DID Subt. B 00/02 5.7.10.
Technical Manual 5.8 Installation Vandal contact The device has two vandal contacts (tamper). A switching contact (1) is opened if the housing cover is removed. Another switching contact (3) is opened if the device is removed from the wall. Switching contact (3) is deactivated by the jumper with designation TE- (2) in the delivery state. To activate the switching contact (3), the jumper TE- (2) must be removed.
Installation 5.9 Technical Manual Fastening the cover Fasten the housing cover in the following way: 1. Hang the mounting lugs of the housing cover at the top of the bottom part of the housing. 2. Pivot the housing cover down and close the housing. 3. Fasten the housing cover by means of two screws M3x8 (TORX 8) on the bottom part of the housing.
Technical Manual Start-up 6 Start-up 6.1 Network requirements Start-up and communication in regular operation are done via an Ethernet network. To guarantee unhindered and trouble-free data traffic, the UDP ports used for communication must have been enabled. The firewall configuration must therefore be adapted accordingly. 6.1.1 Communication The UDP port used for communication between B-COMM and the terminal must have been enabled. The UDP port is in the range from 7700 hex. to 77EF hex.
Start-up 6.2 Technical Manual Automatic registration via B-COMM Start-up of the access manager takes place largely automatically in connection with the B-COMM communication software. The device is preset at the factory for automatic registration via B-COMM. System requirements • B-COMM communication software version 3.10 and higher. • Network with a working DHCP server. Start-up procedure 1. Connect the access manager to the network and switch it on.
Technical Manual Start-up 6.3 Start options 6.3.1 Performing a cold start NOTICE When performing a cold start, parameters are reset to their default values. Master records and booking records are deleted. Network settings as well as group and terminal addresses remain unchanged. 1. Turn off the device. 2. Turn on the device. ð The yellow status LED is lit. ð After approx. 40 seconds, the yellow status LED starts flashing. 3. Within 10 seconds, press the reset key and keep it depressed.
Start-up 6.3.2 Technical Manual Perform a cold start and set the default IP address 123.0.0.2 When performing a cold start, parameters are reset to their default values. Master records and booking records are deleted. 1. Turn off the device. 2. Turn on the device. ð The yellow status LED is lit. ð After approx. 40 seconds, the yellow status LED starts flashing. 3. Within 10 seconds, press the reset key and keep it depressed. ð The status LED flashes faster for 5 seconds.
Technical Manual 6.4 Start-up Service Interface The device is provided with a service interface allowing you to make manual settings. Access takes place via the network connection of the device, either directly or via the network. For direct connection, an Ethernet cross-over cable (crossed RJ-45 cable) or an Ethernet patch cable 1:1 can be used (Auto MDIX). The service interface can be accessed from a service PC via web browser by typing the device IP address into the address box.
Start-up 6.4.3 Technical Manual Overview of the service functions SYSTEM Function Description Information System Information Information on hardware and software of the device and display of IP address and MAC address Statistics Time elapsed since last system start License Display of the current software license Create temporary test license Creation of a temporary test license with full functionality. This test license allows you to use all options.
Technical Manual 6.4.5 Start-up Network settings Function call: Menu > SETTINGS > Network > Network Settings Getting an IP address from the DHCP server 1. Tick “Enable DHCP”. 2. Enter the IP address of the DNS server in the “DNS Server Address” input field. Enter 0.0.0.0 if no DNS server is to be used in the network. Requesting the IP address from the DHCP server on the basis of the terminal name 1. Tick “Enable DHCP”. 2. Enter the “Terminal Name” and “Terminal Domain Name” according to RFC 1123. 3.
Start-up Technical Manual Group identification and device identification The group and device identifications are used to address a device. This identification is part of each parameter record and each data record. 1. Enter the group identification in the “Group ID (GID)” input field. 2. Enter the device identification in the “Device ID (GID)” input field. Value range: GID: 00 to 29, DID: 00 to 59.
Technical Manual 6.4.6 Start-up Host settings Setting of the communication type and definition of the host computer. Function call: Menu > SETTINGS > Network > Host Settings Communication via Ethernet / UDP This is the standard communication type 1. Set the “ETH/UDP” interface. 2. Enter the IP address of the computer communicating with the terminal software in the “Host name or IP address” field. If a DNS has been configured, it is also possible to specify the host name in this field. 3.
Start-up Technical Manual Encryption The “Enable encryption” check box is used to enable and disable the encryption via Ethernet. A license is required for this function. Proxy server If a proxy server is used: 1. Enable “Use a Proxy Server”. 2. Enter the proxy server name or IP address and the port.
Technical Manual 6.4.7 Start-up FTCS host settings Definition of the FTCS (Finger Template Control Server). Function call: Menu > SETTINGS > Network > FTCS Settings These settings are required if subterminals with biometric readers are connected. The settings are only required if the FTCS service is provided by a separate host server. 1. Enter the IP address of the computer on which the FTCS service is running (BCOMM server).
Start-up 6.5 Technical Manual Device Discovery Tool The Device Discovery Tool allows a manual device start-up without automatic registration via B-COMM. The Device Discovery Tool is started on a service PC. It detects any devices available in the network which wait for the host registration using the B-Client AC30 terminal software and displays them. After selecting a device, the network parameters can be adjusted. 6.5.1 System requirements The program is an executable Java archive (.
Technical Manual 6.5.4 Start-up Changing network parameters After selecting a device in the list, the current version of the installed terminal software is additionally indicated. Furthermore the network parameters are displayed. IP address, net mask and gateway can be changed, if required. Assigning a new IP address and disabling the host registration 1. Select the device to be changed in the list. 2. Enable the "Set static IP address" check box. ð The input fields are active. 3.
Start-up 6.6 Technical Manual SFTP server The device provides an SFTP server for a secure, encrypted connection via the “Secure File Transfer Protocol” (SFTP). 6.6.1 Prerequisites For the SFTP to access the terminal, the following is required: 6.6.2 • SFTP client, for example WinSCP. WinSCP (Windows Secure CoPy) is a free “open source” SFTP and FTP client for Microsoft Windows. • Kaba key file.
Technical Manual Start-up 3. Enter pass phrase. Pass phrase for standard Kaba key = kaba 4. Click "OK" ð The connection to the terminal is being established.
Packaging/Return 7 Technical Manual Packaging/Return Incorrectly packaged assemblies and devices may cause expenses due to damage during transport. Please observe the following information when sending Kaba products. Kaba shall not be liable for damage to products which can be attributed to insufficient packaging. 7.1 Complete Devices The original packaging is specially adapted for the device. It offers the greatest possible protection against transport damage.
Technical Manual 7.3 Packaging/Return Marking Complete return papers and correct labeling allow us to process matters quickly. Please ensure that a delivery note is included with the package. The delivery note should include the following information: • Number of devices or components per package. • Item numbers, serial numbers, designations. • Address of your company/contact. • Reason for the return, e.g. repair exchange. • Informative description of the fault.
Disposal 8 Technical Manual Disposal This product meets the requirements of the WEEE Directive and, in accordance with DIN standard EN 50419, is labeled with the WEEE crossed-out garbage can symbol. The symbol indicates the separate disposal of electric and electronic equipment in EU countries. Do not dispose of the device with household waste under any circumstances. Used devices contain valuable recyclable materials that should be recycled.
Technical Manual Appendix 9 Appendix 9.
Appendix Technical Manual Index Numerical F 24 V DC input.............................................................................. 17 Fast online.................................................................................... Fastening dimension ............................................................... Fastening the cover.................................................................. FTCS host settings.....................................................................
Technical Manual O U Offline operating state ............................................................ 28 Online operating state ............................................................ 28 Operating states ........................................................................ 28 Output voltages......................................................................... 17 Outputs ................................................................................... 18, 57 Update records .............
