Manual doro R52
7 1 2 3 6 5 4 1 Two-way recording/Memo 5 Stop / On/Off 2 Delete message 6 Set Clock/Skip Message 3 Repeat/OGM record 7 Volume Control 4 Play/Pause
English Installation Battery To ensure that messages and time/date information will be retained during a possible power cut (max. 16 hours), a 9V – PP3 battery is required (not supplied). When the battery is running low, the display will flash Lo, change the battery as soon as possible. Use only a high quality Alkaline battery. 1. Ensure the telephone line cord is disconnected. 2. Remove the battery cover. 3. Connect the battery observing correct polarity. 4. Replace the battery cover.
English Operation About the Answering Machine The answering machine has to be turned on in order to receive messages. When a call is received it will be answered after the selected number of rings (please refer to page 5). When the answering machine answers an incoming call, the caller will hear your outgoing message. After a short beep they can then leave a message up to 300 seconds (user selectable 60/300 seconds). Should the caller exceed this limit the call will be disconnected.
Operation English Number of Rings Use the 2 7 TS switch at the rear of the machine to select after how many rings the unit will respond to an incoming call. 2 = calls are answered after two rings. 7 = calls are answered after seven rings. TS (TOLL SAVER) – activates the toll save function. In Toll Saver mode incoming calls are answered after seven rings until the first new message has been recorded. Once a message has been recorded the answering machine will answer after approximately two rings.
English Operation Outgoing Message The outgoing message is your message to an incoming caller and may be up to 30 seconds in length. You may want the message to tell the caller that they may start speaking once the beep is heard after your outgoing message. If you choose not to record your own outgoing message the caller will hear a prerecorded message.
Operation English Playback of messages The display flashes to show how many new messages have been received. If no new messages have been received the display shows total messages (old). Playback will always begin with any new messages, for example if there are three old messages and two new ones, only the two new ones will be played back, then the answering machine will return to standby mode. Press the play button once again to listen to all messages, starting with the oldest messages. 1.
English Operation Personal Message - MEMO A personal message – MEMO – is a message recorded directly onto the answering machine (60 seconds maximum) without dialling. This means that the answering machine may be used as an electronic notebook, where messages, reminders or other notes to family members or colleagues can be recorded. 1. Press and hold the a button. You will hear a beep. 2. Start speaking clearly towards the machine to record your Memo message. 3. Release the a button to stop recording. 4.
Operation English Remote Control 1. Call up the answering machine. 2. While the outgoing message is playing, enter the remote code. If the code is accepted, you will hear two beeps. 3. Select a remote control command (within 10 seconds) from below. 4. When you have finished accessing the machine replace the handset. Command Function 1#........................................ Play new messages 2# ....................................... Play all messages During playback: 3#................................
English Other Remote Activation The answering machine can be activated using the remote control functions. 1. Call up the answering machine. After approximately 16 rings, the machine will answer and emit a long tone. 2. Enter the remote code, printed underneath the unit. If the code is accepted, you will hear two short beeps. 3. Press 7# . One beep confirms that the answering machine is now on. Replace the handset.
Other English Troubleshooting Check that the telephone cord is undamaged and properly plugged in. Disconnect any additional equipment that may be connected. If the problem is resolved, the fault is with the other equipment. Test the equipment on a known working line. If the product works then the fault is with the line. Please inform your local telephone company.
English Other To reset the unit If unsuccessful in rectifying any of the above or an unusual symptom occurs, the unit can be reset as follows: 1. Unplug the power adaptor and telephone line from the power outlet and wall socket. 2. Remove the back-up battery. 3. Plug the adaptor back into power socket. 4. If necessary replace the back-up battery. 5. Plug the telephone line into the wall socket. 6. Record a new outgoing message 7. Set date and time.
Other AUSTRALIA DORO Australia Pty Ltd PO Box 6760 Baulkham Hills BC NSW 2153 Australia NEW ZEALAND Atlas Gentech (NZ) Limited Private Bag 14927 Panmure Auckland New Zealand Consumer Support Ph: Ph: 1300 885 023 Fax: (02) 8853-8489 Email: support@doro.com.au Web site: www.doro.com.au Consumer Support Ph: 0900-500-25 (Toll Call) Fax: (09) 574-2722 Email: support@atlasgentech.co.
Australia(English) Version 1.
