ARMBAND USER GUIDE
Table of Contents Purpose of the System .......................................................... 02 Wearing the Armband ........................................................... 03 Removing the Strap/Wing Assembly From Armband.......... 03 Armband Care and Maintenance .......................................... 04 Status Indicators ................................................................... 05 Important Information About the Armband ........................ 07 Product Specifications..............
Purpose of the System Intended Use The exerspy calorie and activity tracking system works with the dotFIT Me Program to record, analyze and report parameters. These objective health metrics enable you to maintain a healthy weight and an active lifestyle, which are continually cited as the keys to combating and managing serious medical conditions including obesity, cardiovascular disease and diabetes.
Wearing the exerspy Armband TM Refer to the enclosed Start Here! card for instructions on how to start using your exerspyTM activity and calorie tracking system. The exerspy armband (the “armband”) is designed to be worn on the back of the upper left arm (the triceps) with the logo towards the shoulder and the sensors touching the skin. 1. Slide the armband onto your left arm. 2. Adjust the strap so that it fits on your arm comfortably, and secure the pull-tab.
exerspyTM Armband Care and Maintenance Clean the armband daily especially after sweating or when it becomes noticeably moist or dirty. Disinfecting the armband with isopropyl alcohol may be required occasionally. Failure to keep the armband clean or improper cleaning may irritate the skin and affect the sensor performance. Cleaning To clean the armband: Gently wipe the side of the armband touching the skin with a soft cloth or towel moistened with a mild soap and water.
Status Indicators Power The armband does not have a power button. When the armband makes secure contact with your body it will power on automatically. This may take up to 10 minutes. Activation is indicated by a series of audio tones. Battery It is recommended to fully charge the battery before use. To charge the battery, remove the armband strap and plug the USB cable into your PC. Then plug the other end of the USB cable into the armband.
Memory During steady use the armband will hold 14 days of data. To check the memory status, remove the armband and press the Status Button. The memory light will turn on as follows: upload data before continuing use. Status Button Status Lights For more information or troubleshooting help, please go to www.dotFIT.com/exerspyhelp or call Technical Support at 877.436.8348.
Important Information About the Armband Follow operating instructions CAUTION Non-ionized radiation The Waste Electrical and Electronic Equipment Regulations indicates separate collection for electrical and electronic equipment Electrical Safety Type B Applied Part FCC Logo CE (Conformité Européenne) mark Information on Proper Disposal of the exerspyTM Armband Attention: If you want to dispose of the equipment, please do not use the ordinary trash! The product must not be disposed of with your other househo
Cautions Always consult a physician before starting any new diet or exercise program. This system is not to be used for diagnostic purposes. This system is not intended as a substitute for the medical advice or supervision of your personal physician. CAUTION: This product is not defibrillation proof. CAUTION: Do not get the device close to other devices that can cause electromagnetic interferences of any nature.
Important Information About the Armband (Continued) CAUTION: Reminders should not be used for life-critical events, such as taking certain medications, if they are vital to your daily health. CAUTION: When the armband is on the arm, DO NOT connect it to the USB cable. CAUTION: If you have known metals allergies, you should consult your physician prior to wearing. CAUTION: Check armband for sharp edges or damage before each use.
CAUTION: To reduce the risk of skin irritation, be sure to dry your arm throughly before wearing the armband. CAUTION: DO NOT IMMERSE THE ARMBAND IN WATER. The armband is not designed to be used underwater or to come in continuous contact with water. CAUTION: Though the armband was designed for wearability and long-term use, it is a sensitive monitoring device. Rough handling can break internal components. Never drop or shock the armband and always store it in a safe place when not in use.
Product Specifications Sensors: Accelerometer (3-axis) Heat Flux Skin Temperature Galvanic Skin Response (GSR) Materials: Armband: ABS, polycarbonate, thermoplastic polyurethane, 304 grade stainless steel Adjustable strap/wing assembly: Nylon, polyester, Lycra (no latex content) or polyisoprene, polycarbonate, thermoplastic polyurethane, silicone Battery type: Internal lithium polymer cell battery RF Frequency: 2.
Accuracy Accelerometer (3-axis) Calibrated range is +/- 2.0g The minimum resolution is 0.01g Galvanic Skin Response Calibrated Range is 56k Ohms to 20M Ohms (50.0 nSiemens – 17.0 uSiemens) Two-standard-deviation accuracy of +/0.05g, up to 1.0g on longitudinal axis Two-standard-deviation accuracy of +/- 7.0 nSiemen up to 233.34 nSiemens reading Two-standard-deviation accuracy of +/-12.0% of expected value otherwise on the longitudinal axis Two-standard-deviation accuracy of +/3.
User Environment 2.5m 1.5m 1.5m 1.5m Computer and Wireless Communicator Diagram not to scale. Guidance and Manufacturer’s Declaration - Emissions The armband is intended for use in the electromagnetic environment specified below. The customer or user of the armband should ensure that it is used in such an environment. Emissions Test Compliance Electromagnetic Environment - Guidance RF Emissions CISPR 11 Class B, Group 1 The armband uses RF energy only for its internal function.
Guidance and Manufacturer’s Declaration - Immunity The armband is intended for use in the electromagnetic environment specified below. The customer or user of the armband should ensure that it is used in such an environment. Immunity Test IEC 60601 Test Level Compliance Level Electromagnetic Environment - Guidance ESD IEC 61000-4-2 ±6kV Contact ±8kV Air ±6kV Contact ±8kV Air Floors should be wood, concrete, or ceramic tile. If floors are synthetic, the r/h should be at least 30%.
User Environment (Continued) Guidance and Manufacturer’s Declaration - Emissions The armband is intended for use in the electromagnetic environment specified below. The customer or user of the armband should ensure that it is used in such an environment.
Recommended Separation Distances for the Product The armband is intended for use in the electromagnetic environment specified below. The customer or user of the armband can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF Communications Equipment and the armband as recommended below, according to the maximum output power of the communications equipment.
Regulatory Statement FCC Declaration of Conformity – We, BodyMedia, Inc., 4 Smithfield Street, 11th Floor, Pittsburgh, PA 15222, phone: 412-288-9901, declare under our sole responsibility that the products, BodyMedia, Inc. and BodyMedia® Armband Model MF, complies with part 15 of the FCC rules.
CENELEC EN 60601-1-1 - Medical electrical equipment - Part 1: general requirements CAN/CSA-C22.2 No.606.1-M90 ETSI EN 301 489-1 - Electromagnetic Compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) Standard for Radio Equipment and Services; Part 1: Common Technical Requirements V1.3.1 ETSI EN 301 489-3 V1.2.1 (2005 -09) - Electromagnetic Compatibility and Radio Spectrum Matters (ERM); Harmonized EN for ElectroMagnetic Compatibility (EMC) of Radio Comms.
dotFIT, LLC 250 N. Westlake Blvd., Ste 220 Westlake Village, CA 91362 877.436.8348 www.dotFIT.
