INSTALLATION GUIDE KT-CDR2 & KT-CDR3 Including Mounting & Sealing of Housing & Electrical Details For COOLDOME™ ENCLOSURE SERIES KT-CDR2 For D2 COOLDOME™ KT-CDR3 For D3 COOLDOME™
PRODUCT INSTALLATION PRECAUTIONS – WARNINGS – ADDITIONAL INFORMATION (RETAIN THIS DOCUMENT) IMPORTANT SAFEGUARDS 1 Read Instructions - All the safety and operating instructions should be read before the unit is operated. 2 Retain Instructions -The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the unit and in the operating instructions should be adhered to. 4. Follow Instructions -All operating & user instructions should be followed. 5.
Electrical Conduit Guidelines For optimal performance, your Dotworkz Enclosure is designed to be Air & Water Tight to eliminate any moisture, dust, and insect damage, safety, performance, reliability, and maintenance related issues. Use of Electrical Conduit, without sealing the entry ports/ inside wire feeds within Camera Enclosure, will subject the inside of your enclosure to possibility of condensation driven moisture, dust, and insect contamination hazards.
VENT STOPPER PLUGS for Conduit Foam Conduit Feed Plugs for ½” I.D. (PG-13) Conduit Prevents Humid Air exchange from venting thru electrical conduit into Dotworkz sealed enclosures, Thus eliminating condensation issues within Dotworkz sealed enclosures. QUICK INSTALLATION GUIDE 1) Pull wires to final installed length. 4) Push plug into conduit mouth with finger tips till it flush with outside of fitting 2) Open Vent Stop Plug and install over wire.
COOLDOME™ Wiring NO 18 gg Dotworkz CD Series Operate using DC low voltage only, and creates ample currents when cooler is engaged. 18 gg wire is Not recommended for cooler wiring. Follow relevant Cable Gauge Guidelines provide in this document applicable to your product model. CD’s are Dedicated 12 VDC or 24 VDC models Only. Use Step Down Power supply Included in CD Package to power from high voltage line supply.
Proper Cable Management to Enclosure Avoid common Installation Mistakes Only Use Qualified Installation or Service Technician for Installing & Servicing Dotworkz Enclosures. Power Must be disconnected and kept off while installing or Servicing Enclosure. Follow All Local and Applicable Electrical Codes and Standards for Installation of Electrical components. All Cable Ports, wire feeds, or Conduit must be fully sealed to eliminate moisture within Enclosure.
Tools Recommended for Enclosure & Camera Mounting Hand Tools Drill & Bits Pole Strapping Tools - #1 & #2 Phillips head screw driver -#1 Flat Blade screw driver or smaller - 3/8 Socket wrench, nut driver, or adjustable wrench - 5/16 Socket wrench, nut driver, or adjustable wrench - 7/16 Socket wrench, nut driver, or adjustable wrench - 7/32 Socket wrench, nut driver, or adjustable wrench - 11/32 Socket wrench, nut driver, or adjustable wrench - Wire stripping tool - Caulk Gun & Silicone Sealant For Wall M
KT-CDR2 & KT-CDR3: Power & Cable Hook Up The provided Dotworkz D2 COOLDOME enclosure is Powered by dedicated 12 VDC Only, (or 24VDC on 24V models) and must use step down Power Pack Pole Mount to be powered by High Voltage Never apply High Voltage directly to inputs directly inside enclosure to power COOLDOME. Power must be shut off during installation. Installation must be done by a qualified electrical technician. Read and Understand all product instruction before installation.
Detail Specifications STRAPPING: Slots Compatible with All DOT-rated ½” minimum, to 3/4” wide max. Stainless Steel Strapping Bands Use Center face slots for Strapping onto small diameter poles (1-7” dia.), Use Side slots for larger diameter poles Lag Bolting: Four (4) x 0.