Headset Microphones Manual d:fineTM Omnidirectional d:fineTM 4065 d:fineTM 4067 d:fineTM 66 d:fineTM Directional d:fineTM 4066 d:fineTM 4088 d:fineTM 88 w w w. d p a m i c r o p h o n e s . c o m www.dpamicrophones.
How to tell the difference between d:fineTM Headset Microphone capsules Introduction All the d:fineTM Headset Microphones provide a uniquely natural and open sound. Ultra-lightweight and adjustable, d:fineTM Headset Mics ensure a secure and comfortable fit in live performance environments. To ensure optimal performance of your d:fine Headset Mic, please follow the simple instructions below.
Adjusting the d:fineTM 4065 4065 is pre-formed but may require adjustment in order to get a tight, fixed position to the back of the neck. Adjust the steel tube carefully at the curves. A protection grid is mounted over the microphone head. If clogged with dirt or make-up, gently remove it and clean it with distilled water. Adjusting the d:fineTM 4066, 4067, and 4088 The size of the headset mount can easily be adjusted. Change the standard bend by carefully expanding the distance between the earhooks.
Position the microphone properly by pulling or pushing the boom along the slide. Switch between left and right ear wearing style simply by rotating the microphone boom. Hold on to the earhook while gently turning the boom. For the dual-ear versions, also rotate the two earhooks. Service connector for exchange of cables or booms on the d:fineTM Omnidirectional, d:fineTM Directional, d:fineTM 66 and d:fineTM 88 These d:fineTM Headset Microphones offer exchange of cables or microphone booms.
Protection cap The d:fineTM Omnidirectional and d:fineTM Directional microphones come with a red plastic cap which serves to protect the microphone head when putting on make-up, hairspray and more.Remove the cap before use. Clothing clip for d:fineTM Omnidirectional, d:fineTM Directional, d:fineTM 66 and d:fineTM 88. The supplied clothing clip allows you to attach the cable to your clothes, thus relieving the cable draw to the headset mic. This is essential on the single-ear headset mic.
Frequency Response of d:fineTM Omnidirectional Polar Pattern of d:fineTM Omnidirectional Frequency Response (d:fineTM 4065, 4066, 4067 and d:fineTM 66) Polar Pattern (d:fineTM 4065, 4066, 4067 and d:fineTM 66) 10 0 5 dB dB -10 5 -20 -30 20 Hz 80 Hz 50 100 200 500 1 kHz 2 5 10 20 40 125 Hz 4 kHz 8 kHz 1 kHz 2 kHz 20 kHz 250 Hz 500 Hz 16 kHz 1 kHz 8 kHz 2 kHz 20 kHz 16 kHz 4 kHz Frequency Response of d:fineTM Directional Polar Pattern d:fineTM Directional 10 0 5 dB dB -10 -20
Directional characteristics Omnidirectional Principle of operation Pressure Frequency range 20 Hz - 20 kHz Frequency range, ± 2 dB d:fine omnidirectional 20 Hz - 20 kHz with 3 dB soft boost at 8 - 15 kHz 4065, 4066, 4067 and d:fine 66: 20 Hz - 20 kHz with 3 dB soft boost at 8 - 20 kHz Sensitivity, nominal, ± 3 dB at 1 kHz 6 mV/Pa; -44 dB re. 1 V/Pa Equivalent noise level, A-weighted Typ. 26 dB(A) re. 20 µPa (max. 28 dB(A)) S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL) Typ.
