Specification Sheet

1.0 General Data
1.1 Manufacturer
1.2 Designation
1.3 Dräger Part Number
EAN Code
1.4 Intended Use
1.5 Relevant Standards
1.6 Certification Body
2.0 Design & Construction
2.1 Filter Connection
2.2 Material
2.3 Construction
2.4 Working Principle
2.5 Sizes
2.6 Service-Life
2.8 Weight (approx.)
3.0 Performance
3.1 Inhalation Resistance
3.2 Exhalation Resistance
3.3 Temperature Resistance
3.4 Flammability
3.5 Speech Diaphragm
3.6 Inward Leakage
Dimensions (approx.)2.7
S: R 55 351 M: R 55 350 L: R 55 352
4026056001064 4026056001071 4026056001088
EN 140:1998 Federal register
42 CFR part 84
(1)
AS/NZS 1716:2003 GOST R 12.4.190-99
DEKRA EXAM GmbH
Dinnendahlstr. 9
44809 Bochum
Germany
Reference number: CE
0158
National Institute for
Occupational
Safety and Health
(NIOSH)
626 Cochrans Mill Road
Pittsburgh, PA 15236
USA
SAI Global Assurance
Services Ltd
Winterhill House
Snowdon Drive
Milton Keynes MK6 1AX
United Kingdom
VNIIS, JSC
3/10, Electrichesky Ln.
Bld. 1
Moscow 123557
Russia
Mask Body:
Mask Yoke:
Head Cradle:
Head Strap:
Inhalation Valves:
Exhalation Valve:
Size: Small Height: 115mm Width: 104mm Depth: 72mm
Size: Medium Height: 128mm Width: 103mm Depth: 73mm
Size: Large Height: 139mm Width: 109mm Depth: 74mm
S/M/L 95g 99g 103g
Thermoplastic Elastomer (TPE) and Polyprophylene
Polyprophylene
Thermoplastic Elastomer (TPE) and Polyprophylene
Polyester / Elastodien / Cotton
Natural Rubber
Nitrile Rubber (NBR)
The X-plore® 3500 half mask consists of six main components: mask body, mask yoke, head cradle,
head straps, exhalation valve and (2) inhalation valves. The mask body is constructed of a soft
component and a hard component that is specially bonded to maintain its form. The mask yoke covers
the front of the mask body and is a guide for the routing of the head straps. The head cradle utilizes a
hard component for the head strap adjustment that specially bonded to a soft component that fits on
crown of head. The inhalation valves are flat discs that only allows air into the mask and the exhalation
valve is of a stepped design to apply even sealing pressure that only allows air to exit the mask.
The half face mask, in combination with two breathing filters, offers respiratory protection against
potentially hazardous gases, vapors and/or particles. Scope and effectiveness of respiratory protection
results from the combination of half mask with suitable and certified respiratory protective filters, along
with following local regulations on use limitations.
The sealing line on the inside of the mask body conforms to the face of the wearer along the cheeks,
over the nose and under the chin. A head harness with adjustable straps and a clasp firmly holds the
mask onto the face.
During inhalation, ambient air passes through the filters where it is "cleaned," and then into the mask.
During exhalation, air passes through the exhalation valve only since the inhalation valves close. This
prevents exhaled humidity from affecting the filters and reduces "dead space."
Small, Medium and Large
Only certain components (e.g. exhalation valve) must be periodically replaced. See Instructions For
Use for details. There are no time limitations on mask materials assuming proper storage,
maintenance and cleaning as stated in IFU. Damage and wear are outside of this statement.
to EN 140 (pre-conditioned at +70°C and -30°C and t hen tested)
< or = 3.0 mbar @ 160l/min constant flow
< or = 0.5 mbar @ 30 l/min constant flow
< or = 1.3 mbar @ 95 l/min constant flow
< or = 2.0 mbar @ 160 l/min constant flow
Dräger-specific bayonet connection
Dräger Safety AG & Co. KGaA
Dräger X-plore® 3500 Half Mask Respirator
Technical Data Sheet
Dräger X-plore® 3500
Air Purifying Respirator
Respirator for protection against particulates, gases and vapors in conjunction with suitable respiratory
filters. The scope is limited by the product documentation, technical standards, installed application
rules and choice of respiratory filters.
< or = 2.0% average (to EN 140)
n/a
to EN 140 (exposed to 800°C flame and must not burn for > 5s after removed)