Dr. Infrared Heater Elite Series 1500 Watts with Two Heat Settings Built-In Humidifier Rotatable Air Outlet Automatic Thermostat Tip-Over Switch Overheat Thermal Cut-Off Protection Room Temperature LED Display Precision Temperature Control Easy Push-Button Controls Remote Control Model No.
CONGRATULATIONS! he Dr. Infrared Heater Elite Series you have just purchased is a safe and powerful heater, designed to heat a room after a few minutes of operation. The far-infrared Quartz-PTC heating system is an excellent system for safely heating whole rooms, while saving on heating costs. T Additionally, this heater includes an overheat protection system, and an inlet air overheat protection system designed to ensure your safety.
. Extreme caution is necessary when any heater is used by or near children or persons with physical challenges and whenever the heater is left operating and unattended. 4. Do not operate the heater with a damaged cord or plug, or after the heater malfunctions, has been dropped, or damaged in any manner. Return the heater to an authorized service facility for examination, electrical or mechanical adjustment, or repair. 5. Do not use outdoors. 6.
16. Always unplug heater when not in use. 17. Always plug heater directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip). 18. It is normal for the heater’s plug and cord to feel warm to the touch. A plug or cord which becomes hot to the touch or becomes distorted in shape may be a result of a worn electrical outlet. Worn outlets or receptacles should be replaced prior to further use of the heater.
Water Tank Seal Installation Guide A. Install the rubber seal ring before use. B. Wrap the ring around the tube. C. Make sure the rubber ring is in the concave area.
Water Bottle Adapter Seal Installation Guide (Seal may come in black or white) A. Install the rubber seal ring on the water bottle adapter before use. B. Wrap the ring around the tube. C. Make sure the rubber ring is all the way inside.
2. Take out the water bottle (Max. 500 ml.) from the package and fill the water bottle with distilled water. Then tighten the connector on the water bottle as shown in Figure 2. FIG 2 CAUTION: You must use distilled water to keep the humidifier working properly. Also, make sure the connector is tightened to the bottle to prevent water leakage. 3. Fully insert the humidifier into the two hooks located in the rear side of the wooden box as shown in Figure 3.
5. Insert bottle, attached to connector, into the humidifier, as shown in Figure 5. FIG 5 Special Features LED Display – When the unit is plugged in, the LED display will show the room temperature. At ECO mode, it will display the set value 2 minutes after the desired temperature is set. Overheat Cut-Off Protection System –This heater includes a protection system that cuts off the unit if it overheats for any reason.
A H TM B C D E F G Features A. “Cool-Touch” cabinet B. POWER button C. Rotatable air outlet button D. Humidifier button E. Decrease temperature button F. Increase temperature button G. MODE/OFF button H.
Steps 1, 2, 3 to turn on the heater Step 1 – Plug in power cord to outlet. Step 2 – Press power button on the unit. Step 3 – Press Mode button on the unit. The heater default setting is 68ºF, if room temperature is above 68ºF, the heater won’t start if the room temperature is higher than the set temperature. Please check Room Temp, and increase Set Temp to start heater. Note: Heater will not turn on if the room temperature is higher than 86ºF.
Operating Instructions 1. Plug the power supply cord into a grounded wall outlet (120VAC, 60Hz). Important: This heater comes with a grounded (three-prong) plug. The grounded plug must be used with a grounded outlet. Do not use an adapter in a two-slot wall outlet unless the ground plug of the adapter properly connects to a building ground. Using the heater without a properly grounded outlet or adapter could result in an electric shock hazard. The cord has a plug as shown at A in the figure that follows.
component cooling process before turning off the fan. Once the desired temperature is achieved, the heater will maintain the room to the set temperature. 6. LOW POWER MODE – 1000W LOW mode will control the heater to operate at low power until the room reached the set temperature. The heater will stop heating and initiate component cooling process before turning off the fan. Once the desired temperature is achieved, the heater will maintain the room to the set temperature. 7.
11.SETTING THE AIR OUTLET Press the OSC button. The air outlet can be rotatable left and right. For more efficient heating, try placing the heater a few feet above the floor in rooms with a large area. Ensure the heater is secure and won't fall. Remote Controller HOW TO INSERT BATTERIES NOTE: Remove the batteries if the remote control is not to be used for a month or more. Batteries left in the unit may leak and cause damage.
Maintenance 1. Always turn OFF the heater and disconnect the cord from the electrical outlet before cleaning the unit. 2. Light accumulation of dust may be removed from the heater with a soft cloth or vacuum cleaner. 3. Wipe the exterior surfaces of the heater occasionally with a damp cloth (not dripping wet), using a solution of mild detergent and water. Dry the case thoroughly before operating the heater.
Cleaning the humidifier The humidifier should be cleaned once per month or as needed to ensure efficient operation. 1.Power the heater OFF by pressing the POWER button located on the left side of the Control Panel. 2. Unplug the heater’s power cord. 3. Press the two hooks in the rear of the wooden box and push out the humidifier. 4. Open the cover of the humidifier. 5. Clean the humidifier with water. Warning! Any other servicing needed must be performed by an authorized service representative.
Model No.: DR-998 Voltage: 120V, 60Hz Current: Maximum continuous draw: 12.5 amps Output: 5200 BTUs Power: 1500 Watts Blower: Multi-blade; Low Noise, High Pressure In The Box DR Infrared Portable Space Heater with Humidifier Remote control (2 AAA batteries) User’s Manual Warranty Information Register your product at our website: Or visit DrHeaterUSA.com/register-your-heater Feedback Love it? Help us make the product more for you. Let us know with a customer review. Please visit: https://www.
How long is the warranty? This heater comes with a THREE-YEAR LIMITED WARRANTY. If your unit does not appear to be working properly, please contact our service center by calling 1-800-317-1688. Prior to your call, we encourage you to visit our service related website www.DrHeaterUSA.com for troubleshooting tips and service instructions if needed. Dr. Heater USA 860 Mahler Road Burlingame, CA 94010 Tel: 1-800-317-1688 EMAIL: SERVICE@DRHEATERUSA.COM Dr Heater USA @Dr Heater USA Dr. Heater USA Dr.
QUESTIONS AND ANSWERS Why does the blower fan keep running after I have pressed the power off button? The blower fan will continue to run until the heat chambers cool down. After a few minutes the fan will shut off automatically. What if the heater’s airflow seems to have diminished? Please ensure the rear intake is not blocked and that the filter is clean. Please follow the filter maintenance procedure to clean the filter.
desired temperature, it will cycle on and off accordingly. Can the heater be used in a bathroom? It is not recommended due to a bathroom’s high level of moisture. Can the heater be used in a basement or garage? Yes, but keep in mind that rooms with little insulation will not retain the heat as efficiently. Bare concrete floors act as a heat sink with any type of heating and will absorb some of the heat. However, placing the heater a few feet above the floor will allow for more efficient heating.
and one PTC element (which is rated for 80,000 hours and up). What is zone heating? Zone heating focuses heat where people spend the most time. After all, there is no point in heating multiple rooms to +68 degrees when not in use. Can I use an extension cord, surge protector, or power strip with my heater? No. The DR. INFRARED HEATER is designed to plug directly into a grounded 120V 15 Amp or higher circuit receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
