User's Manual
Table Of Contents
- FOREWORD
- 1. SAFETY GUIDE
- 2.DEVICE DESCRIPTION
- 3.INSTRUCTIONS OF USE
- 3.1 Recharging the Pain Therapy Device.
- 3.2 To insert the Pain Therapy Device onto the Ele
- 3.3 To operate the Pain Therapy Device directly or
- 3.4 To prepare the different electrodes to use wit
- 1. Ankle & Foot Therapy Electrodes
- 2.Ankle Therapy Electrodes
- 3.Calf Circulation Promoter Electrodes
- 4.Knee Therapy Electrodes
- 5.Shoulder Therapy Electrodes
- 6.Elbow Therapy Electrodes
- 7.Hand & Thumb Therapy Electrodes
- 8.Knee Band with Electrodes (Fabric type)
- 9.Belt Electrodes I
- 10.Belt Electrodes II
- 11.Backrest Electrodes
- 12.Neck Comforter Electrodes
- 13.Neck Support Brace Electrodes
- 14.Circulation Promoter Pro (CP-Pro)
- 15.Large and Small Patch Electrode
- 16.Pain Therapy Belt with Electrodes (Fabric type)
- 17.Arm Band with Electrodes (Fabric type)
- 18.Triple Action Back Belt with Electrodes (Fabric ty
- 19.Leg Rests with Electrodes - I (Fabric type)
- 20.Leg Rest with Electrodes - II (Fabric type)
- 21.Knee Band with Electrodes (Fabric type)
- 22.Neck Therapy Pro - I
- 23.Neck Therapy Pro - II
- 24.Neck Therapy Pro - IV
- 25.Perfect Back Relief system with Electrodes
- 26.Pain Therapy Shirt
- 3.5 Operation details
- 3.6 Electrode Pads Guideline
- 4.CLEANING AND MAINTENANCE
- 5.STORAGE
- 6. TROUBLE SHOOTING
- 7. DISPOSAL
- 8. WARRANTY CARD
- 9. LABEL SYMBOLS
- 10. ELECTROMAGNETIC COMPATIBILITY
Pain Therapy Device, Models: P.T.S-X User Manual
File No. XB-UM-X-001
Guangzhou Xinbo Electronic Co., Ltd. Page
70
of
83
The use of the remote control:
1. The remote control can be used to adjust the intensity of the stimulation and to select
the mode of therapy 1, 2 or 3 only when the Pain Therapy device is power ON.
2. Press the (M) button on the device or the remote control to select the mode of
therapy. Press the (+) or (-) button on the device or on the remote control to adjust
the intensity of stimulation.
3. You cannot power ON or power OFF the Pain Therapy Device with the remote
control. To power OFF, hold down the (M) button on the Pain Therapy Device for 1~2
seconds.
Note:
Before repositioning electrode pads, turn the device Off first before disconnecting the
electrode pads from your skin. Once you replaced the electrodes back onto your skin,
you can turn the device back On.
If you want to stop the treatment before the Time of treatment is completed, turn the
device Off first then remove the electrode pads from your skin.
Remove the electrodes from your skin by pulling on the electrode pad. Do not pull on the
wire as this will cause damage to the wire connection to the electrode pad.
3.6 Electrode Pads Guideline
1. Only use the electrode pads supplied by the manufacturer; other electrode pads may
pose a risk of unsuitable electrical characteristics with your Pain Therapy Device.
2. Do not use the electrode pads on different individuals, otherwise, skin reaction or
cross infection may occur.
3. Always turn power off before removing or repositioning the electrodes.
4. Make sure the skin has been washed thoroughly before applying the electrodes. Do
not clean the skin with alcohol.
5. For better conduction, moisten your skin with the conductive gel before putting the
pads on.
6. Apply the whole surface of the electrode pads firmly to the skin. Do not use patch
electrode pads that do not stick properly to the skin or only partially stick to the skin.
7. In case of skin redness under the electrode pads after stimulation, do not stimulate in
the same place until the skin turn to normal condition
8. Replace sticky patch electrodes with new ones after using them for 30 times, or
earlier if they fail to stick properly. Replacement sticky patch electrodes are available
at your place of purchase.