Specifications

ManualsBrandsDraper ManualsAir CompressorDA100

100, 150 & 200 LITRE

COMPRESSORS

■ STOCK Nos.77709 ■ PART Nos.DA100/300B

77897 DA150/300B

77711 DA200/300B

GENERAL INFORMATION

This manual has been compiled by Draper Tools and is an integrated part of the product with which it is enclosed

and should be kept with it for future references.

This manual describes the purpose for which the product has been designed and contains all the necessary

information to ensure its correct and safe use. We recommend that this manual is read before any operation or,

before performing any kind of adjustment to the product and prior to any maintenance tasks. By following all the

general safety instructions contained in this manual, it will ensure both product and operator safety, together with

longer life of the tool itself.

All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the

product.

Whilst every effort has been made to ensure accuracy of information contained in this manual, the Draper Tools

policy of continuous improvement determines the right to make modifications without prior warning.

01/2005

• INSTRUCTIONS •

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE

SAFE AND EFFECTIVE USE OF THIS TOOL.

Summary of content (16 pages)

PAGE 1
00, 150 & 200 LITRE COMPRESSORS ■ STOCK Nos.77709 77897 77711 ■ PART Nos.DA100/300B DA150/300B DA200/300B • INSTRUCTIONS • IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL. 01/2005 GENERAL INFORMATION This manual has been compiled by Draper Tools and is an integrated part of the product with which it is enclosed and should be kept with it for future references.
PAGE 2
100, 150 & 200 LITRE COMPRESSORS ■ STOCK Nos.77709 77897 77711 ■ PART Nos.DA100/300B DA150/300B DA200/300B CONTENTS: Contents/Declaration Specification/Guarantee Power Supply General Safety Instructions Getting to Know Your Compressor Assembly Operation and Use Maintenance Trouble Shooting 1 2 3 4 5 6 6-8 8 - 10 11 DECLARATION OF CONFORMITY We Draper Tools Ltd. Hursley Road, Chandler’s Ford, Eastleigh, Hampshire. SO53 1YF. England.
PAGE 3
SPECIFICATION The Draper Tools policy of continuous improvement determines the right to change specification without notice. Stock No. Part No. Voltage Motor 77709 77897 DA100/300B DA150/300B 230V/50Hz 230V/50Hz 3HP (2.2kW) 3HP (2.2kW) 77711 DA200/300B 230V/50Hz 3HP (2.2kW) 1450 1450 145PSI (10bar) 145PSI (10bar) Air displacement 10.4cfm (295L/min) 10.4cfm (295L/min) 10.4cfm (295L/min) Free air delivery 7.2cfm (204L/min) 7.2cfm (204L/min) 7.
PAGE 4
POWER SUPPLY CONNECTING YOUR MACHINE TO THE POWER SUPPLY The machine should be connected to a 16amp power supply either using the appropriate blue 16amp plug or directly into the fused mains supply. Both of these operations should be carried out by a qualified electrician. *WARNING A plug with bare flexible wires exposed is hazardous if engaged in a live power socket outlet. WARNING THIS APPLIANCE MUST BE EARTHED.
PAGE 5
GENERAL SAFETY INSTRUCTIONS FOR COMPRESSORS WARNING: Please read the following instructions carefully, failure to do so could lead to serious personal injury. Read all these instructions before operating this product and save these instructions. IMPORTANT: Draper Tools Limited recommends that this machine should not be modified or used for any application other than that for which it was designed. If you are unsure of its relative applications do not hesitate to contact us in writing and we will advise you.
PAGE 6
GETTING TO KNOW YOUR COMPRESSOR (6) (5) (7) (9) (4) (8) (16) (11) (12) (3) (10) (2) (13) (15) (1) (14) DA150/300B Shown (1) (2) (3) (4) (5) (6) Air Receiver Tank Sump Bung Pump Unit Dipstick/Oil Inlet Pulley Guard Air Filters (7) Drive Belt (8) Motor (9) Overload Protection Switch (10) Safety Valve (11) Pressure Switch (12) In-Line Pressure Gauge (13) Tank Pressure Gauge (14) Tank Bung (15) Tank Rating Plate (16) Pressure Regulator UNPACKING: After removing the packing material, make sure
PAGE 7
OPERATION AND USE POSITIONING: Do not stand the compressor on any surface with a 15° or greater tilt as this will lead to possible running problems. Allow a minimum gap of 50cm around the compressor to aid connection and airflow. In addition to pneumatic air tools, your compressor may be connected to several accessories suitable for blowing, washing and spraying for example. For technical specifications and detailed instructions, please refer to the instructions provided with the individual accessory.
PAGE 8
OPERATION AND USE ADJUSTING THE PRESSURE SWITCH (Fig.5): Note: This is the only operation where it is acceptable to switch the compressor off without using the pressure switch. To decrease the pressure switch, run the compressor up to the desired capacity for the pressure switch to be set. At this point, turn the mains power off and do not operate the red button on the pressure switch as this will release the pressure.
PAGE 9
OPERATION AND USE OVERLOAD CUT-OUT (Fig.7): The compressor is equipped with an overload cut-out (G) which operates as a safety device to protect the motor. The device will activate in case of motor overload or overheating due to operation troubles. In this case, the safety device will automatically activate, disconnecting the compressor and avoiding possible motor damages. To restart the compressor, proceed as follows: - Allow three minutes. - Position the pressure switch to"0" OFF.
PAGE 10
MAINTENANCE In order to keep your compressor in good working conditions, we recommend you to perform periodical servicing operations. Before performing any maintenance operation, switch off the compressor and ensure all air in the tank is released. Fig.8. OPERATIONS TO BE CARRIED OUT AFTER THE FIRST 50 WORKING HOURS: Check that all screws are properly tight, paying special care to the head and crank case. Replace the lubricant with one of the recommended oil listed in the table (page10).
PAGE 11
MAINTENANCE It is advisable to clean all the finned parts of your compressor, so as to keep the cooling system efficient and to ensure a long work life to your machine. Check belt tension. Hang a weight of about 3kg at the midpoint of the belt. The belt should flex about 10mm. (Fig.11). If necessary, tension up the belt taking care not to disturb the pulley-to-flywheel alignment (Fig.12). Fig.11. OPERATIONS TO BE CARRIED OUT EVERY 2 YEARS: Check the non-return valve and if necessary replace the seal.
PAGE 12
TROUBLE SHOOTING USE ONLY ORIGINAL SPARE PARTS, AVAILABLE AT ALL AUTHORIZED SERVICE CENTRES. FAULT POSSIBLE CAUSE REMEDY Pressure drop in tank Air leaks at connections Allow the compressor to reach max. pressure allowed. Switch it of and brush a soapy water solution onto all air connections. Look carefully for air bubbles flowing out. Tighten those connections where leaks are present. If the problem is still present, contact the After Sales Service.
PAGE 13
NOTES - 12 -
PAGE 14
NOTES - 13 -
PAGE 15
NOTES - 14 -
PAGE 16
DRAPER TOOLS LIMITED, Hursley Road, Chandler's Ford, Eastleigh, Hants. SO53 1YF. U.K. Helpline: (023) 8049 4344. Sales Desk: (023) 8049 4333. General Enquiries: (023) 8026 6355. Fax: (023) 8026 0784. http://www.draper.co.uk e-mail: sales@drapertools.com YOUR DRAPER STOCKIST ©Published by Draper Tools Ltd.