Programming instructions

Wiring Instructions
™
SC1-Gen2 Control by Draper
Copyright ©2009 Draper Inc. Form SC1-Gen2_WD09 Printed in U.S.A.
Caution
➀ Make sure power is disconnected before installing controls.
➁ To Reduce the Risk Of Fire, Electric Shock, Or Injury To Persons, Installation
Work And Electrical Wiring Must Be Done By Qualifi ed Person(s) In
Accordance With All Applicable Codes And Standards.
➂ To reduce the risk of fi re and electric shock, install SC1-Gen2 only with listed
window shade operator(s) rated maximum 9.8 amps at 115VAC each.
➃ SC1-Gen2 is a line voltage control, designed to operate one motor. Activation
by low voltage input commands. If you want to switch two or more motors,
ISO relays must be installed in the circuit.
➄ SC1-Gen2 is electrically “hot” on the back of the circuit board. INS-SC1
(Draper Part Number C199.004) insulation board is provided.
Electrical Specifi cations
Input:
Data: +12VDC BUS Commands
Low Voltage: Dry Contact—0v AC
Line Voltage: 85-265VAC 50-60Hz
Output: ½ HP, 115VAC 9.8 FLA / 230VAC 4.9 FLA.
Signal Output is Class 2.
®
If you encounter any diffi culties installing/wiring your IntelliFlex control, call your
dealer or Draper, Inc., Spiceland, Ind., [phone]; or fax [phone].
Dimensions: 2
1
/ 8 " W x 3¼" L x
7
/ 8 " H.
One SC1-Gen2 fi ts in a deep single gang J-Box.
Please Note: When connecting data "BUS," never link an "Eye" port to another "Eye" port. You may
link your BUS from "Eye" to "Aux" or "Aux" to "Aux."
All BUS command input devices must connect to an "Eye" port in order to power the input device.
Wiring Instructions for Controlling Multiple Shades with One SC1
Wiring Instructions for Controlling One Shade with One SC1
Inserting wire into spring terminal
➀ Open spring terminal by inserting screwdriver into upper opening.
➁ Insert wire into lower opening.
➂ Remove screwdriver.
Motor Neutral
-white/blue
Black - Up
Red/Brown
- Down
To
115/230VAC
Motor
115/230VAC
Hot (black/brown)
Neutral (white/blue)
Ground
Data BUS
"Eye" Port
Data BUS
"Aux" Port
Dry input terminals.
This can be any Single
Pole, Double Throw switch
(
Torque dry input screw
terminals to 3 Lb-In.
To
115/230VAC
Motor 1
Green
INPUT INPUT
INPUT INPUT
To
115/230VAC
Motor 2
Green
Neutral Neutral
Up Up
Down Down
Note:
Motor red/brown and
black wires will
need to "flip" if one
motor is right hand
and the other is left hand.
Motor Neutral
-White/Blue
Black - Up
Red/Brown
- Down
To
additional
ISOs
Earth
Ground
Neutral Neutral
Up Up
Down Down
To
Additional
Motor
Green Wire
SC1
ISO
ISO
115/230VAC
Hot (black/brown)
Neutral (white/blue)
Data BUS
"Eye" Port
Data BUS
"Aux" Port
Dry input terminals.
This can be any
Single Pole, Double
Throw switch (Torque
dry input screw
terminals to 3 Lb-In.
Fabric un roll ing from back of
roller (standard)
Fabric unrolling from front of
roller (reverse roll)
Interior
side
Interior
side
Right hand motor
(Standard)
Black—Up
Red/Brown—Down
Left hand motor
Black—Down
Red/Brown—Up
Right hand motor
(Standard)
Red/Brown—Up
Black—Down
Left hand motor
Red/Brown—Down
Black—Up
All connection wires must conform to the motor
manufacturer’s recommendation and prevailing
electrical codes. Use appropriate Class 2 wiring as
determined by location of use or install as required by
Article 725 of the NEC and local codes. USE COPPER
CONDUCTORS ONLY rated at 75° C or higher.
Please Note:
All input devices (low voltage LED switches, IR eye, RF receiver) which connect to the Eye jack must be connected using electrically straight 6-conductor
modular cable (RJ25). This means colors do not cross over: blue leads to blue, green to green, etc. (see diagram below)
Note: Motor red/brown and black wires
will need to “fl ip” if one motor is right
hand and the other is left hand.
Please Note: This confi guration
will limit SC1-Gen2 functions.
Please Note: This device has not been evaluated for reliability to the Standard
for Tests for Safety-Related Controls Employing Solid-State Devices, UL 991
and therefore not considered suitable for entrapment protection.
E317985
3SMW
Part Number C156.065
COLOR PIN # FUNCT ION
WHITE 1 RQRR CLOCK
BLALL CK 2 COMMON
RED 3 +5VDC
GREEN 4 RQRR DADD TA
YELLOW 5 RP DADD TA
BLUE 6 +12VDC
COLOR PIN # FUNCT ION
RQR CLOCK1WHITE
COMMON2BLAL CK
5VDC3RED
RQR DAD TA4GREEN
RP DAD T A5YELLOW
12VDC6BLUE
Six-Pin Layout
Window Shade Control
INCORRECT
Tab facing away (down)
WHITE
BLACK
RED
GREEN
YELLOW
BLUE
Tab facing away (down)
WHITE
BLACK
RED
GREEN
YELLOW
BLUE
PIN 6
PIN 1
PIN 6
PIN 1
CORRECT
Tab facing away (down)
WHITE
BLACK
RED
GREEN
YELLOW
BLUE
Tab facing away (down)
BLUE
YELLOW
GREEN
RED
BLACK
WHITE
PIN 6
PIN 1
PIN 6
PIN 1
Page 41 of 124