Programming instructions

Copyright ©2009 Draper Inc. Form SGC4-Gen2_WD09-R Printed in U.S.A.
Caution
➀ Make sure power is disconnected before installing controls.
➁ SGC4 is a line voltage control, designed to operate up to 4 motors as a
group, activated by Low Voltage input commands.
➂ To Reduce the Risk Of Fire, Electric Shock, Or Injury To Persons, Installation
Work And Electrical Wiring Must Be Done By Qualifi ed Person(s) In
Accordance With All Applicable Codes And Standards.
➃ SGC4 enclosure is 8" x 8" x 4".
➄ Main Disconnect and Branch Circuit Protection provided by installer.
➅ Maximum surrounding air temperature 40° C.
➆ Use copper conductors rated 75° Celsius or higher only, 18-12AWG.
Electrical Specifi cations
Input:
Data: +12VDC BUS Commands
Low Voltage: Dry Contact—0v AC
Line Voltage: 115VAC +/- 10%
Output:
115VAC Largest Motor 1FLA, 4FLA Total
Signal Output Class 2
®
Wiring Instructions
™
SGC4-Gen2 Control by Draper
If you encounter any diffi culties installing/wiring your IntelliFlex control, call your
dealer or Draper, Inc., Spiceland, Ind., [phone]; or fax [phone].
Please Note:
All input devices (low voltage LED switches, IR eye, RF receiver) which
connect to the Eye jack must be connected using electrically straight
6-conductor modular cable (RJ25). This means colors do not cross over: blue
leads to blue, orange to orange, etc. (see diagram below).
Fabric un roll ing from back of
roller (standard)
Fabric unrolling from front
of roller (reverse roll)
Interior
side
Interior
side
Right hand motor
(Standard)
Black—Up
Red—Down
Left hand motor
Black—Down
Red—Up
Right hand motor
(Standard)
Red—Up
Black—Down
Left hand motor
Red—Down
Black—Up
Please Note: This device has not been evaluated for reliability to the Standard
for Tests for Safety-Related Controls Employing Solid-State Devices, UL 991
and therefore not considered suitable for entrapment protection.
Please Note:
Connect all Ground
wires to ground
block provided
To Eye Port
To Switch,
splitter or
other input
device
White (Neutral)
Black (Up)
Red (Down)
To
Motor
White
(Neutral)
Black (Up)
Red (Down)
To
Motor
White (Neutral)
Black (Up)
Red (Down)
To
Motor
White
(Neutral)
Black (Up)
Red (Down)
To
Motor
Ground
Ground
Ground
To
115
VAC
White (Neutral)White (Neutral)
Black (Up)Black (Up)
Red (Down) Red (Down)
Neutral
AC (115VAC)
Programmable Dry
Contact Inputs:
This can be any
Single Pole, Double
Throw switch
Up
Com
Down
Aux Port: Out to
next IntelliFlex motor
control Aux or Eye port
Eye Port: In
from previous
Aux port or
input device
Inserting wire into spring terminal
➀ Open spring terminal by inserting screw-
driver into upper opening.
➁ Insert wire into lower opening.
➂ Remove screwdriver.
Right hand motor
(Standard)
Max of 100 feet of
low voltage cable
between controls,
or control and input
with circuit board.
Note: Motor red/brown
and black wires will
need to “fl ip” if one
motor is right hand
and the other is left
hand.
All connection wires must conform to the motor manufacturer’s recommendation
and prevailing electrical codes. Use appropriate Class 2 wiring as determined by
location of use or install as required by Article 725 of the NEC and local codes. USE
COPPER CONDUCTORS ONLY rated at 75° C or higher.
E317985
3SMW
Part Number C156.059
Please Note:
All input devices (low voltage LED switches, IR eye, RF receiver) which connect to the Eye jack must be connected using electrically straight 6-conductor
modular cable (RJ25). This means colors do not cross over: blue leads to blue, green to green, etc. (see diagram below)
Window Shade Control
COLOR PIN # FUNCT ION
WHITE 1 RQRR CLOCK
BLALL CK 2 COMMON
RED 3 +5VDC
GREEN 4 RQRR DADD TA
YELLOW 5 RP DADD TA
BLUE 6 +12VDC
COLOR PIN # FUNCT ION
RQR CLOCK1WHITE
COMMON2BLAL CK
5VDC3RED
RQR DAD TA4GREEN
RP DAD T A5YELLOW
12VDC6BLUE
Six-Pin Layout
INCORRECT
Tab facing away (down)
WHITE
BLACK
RED
GREEN
YELLOW
BLUE
Tab facing away (down)
WHITE
BLACK
RED
GREEN
YELLOW
BLUE
PIN 6
PIN 1
PIN 6
PIN 1
CORRECT
Tab facing away (down)
WHITE
BLACK
RED
GREEN
YELLOW
BLUE
Tab facing away (down)
BLUE
YELLOW
GREEN
RED
BLACK
WHITE
PIN 6
PIN 1
PIN 6
PIN 1
Page 43 of 124