Programming instructions

Copyright ©2009 Draper Inc. Form SPGC04-Gen2_WD09 Printed in U.S.A.
Caution
➀ Make sure power is disconnected before installing controls.
➁ SPGC4 is a line voltage control, designed to individually operate 4 motors,
activated by Low Voltage input commands.
➂ SPGC4 enclosure is 8" x 8" x 4".
➃ The Main Disconnect and Branch Circuit Protection shall be provided by
installer.
➄ Maximum surrounding air temperature 50° C.
➅ Use copper conductors rated 75° Celsius or higher only, 18-12AWG.
Please Note: This device has not been evaluated for reliability to the Standard
for Tests for Safety-Related Controls Employing Solid-State Devices, UL 991
and therefore not considered suitable for entrapment protection.
®
Wiring Instructions
™
SPGC4-Gen2 Control by Draper
If you encounter any diffi culties installing/wiring your IntelliFlex control, call your dealer or
Draper, Inc., Spiceland, Ind., [phone]; or fax [phone].
Inserting wire into spring terminal
➀ Open spring terminal by inserting screw-
driver into upper opening.
➁ Insert wire into lower opening.
➂ Remove screwdriver.
Electrical Specifi cations
Input:
Data: +12VDC BUS Commands
Low Voltage: Dry Contact—0VAC
Line Voltage: 85-265VAC 50-60Hz
Output:
115VAC 60Hz: Largest Motor 1FLA, 4FLA Total
230VAC 50-60Hz: Largest Motor 1FLA, 4FLA Total
Signal Output is Class 2.
To Switch,
splitter or
other input
device
To
Motor
To
Eye
Port
Dry
Contacts
To
Motor
Black (Dir)
Red/Brown (Dir)
Neutral
To
Motor
To
Motor
Black (Dir)
Red/Brown (Dir)
Neutral
Aux
Port
Neutral
AC (115/
230VAC)
Data cable
from Aux Port
to Eye port of
next SPGC4
Aux
Port
Aux
Port
Aux
Port
Eye
Port
Dry
Contacts
Dry
Contacts
Neutral
Red/Brown (Dir)
Black (Dir)
Neutral
Red/Brown (Dir)
Black (Dir)
Please Note:
Connect all
Ground wires to
ground block
provided.
Eye
Port
Eye
Port
Max of 100 feet of
cable between
controls, or
control and input
with circuit board.
Fabric un roll ing from back of
roller (standard)
Fabric unrolling from front of
roller (reverse roll)
Interior
side
Interior
side
Right hand motor
(Standard)
Black—Up
Red—Down
Left hand motor
Black—Down
Red—Up
Right hand motor
(Standard)
Red—Up
Black—Down
Left hand motor
Red—Down
Black—Up
E317985
3SMW
Part Number C156.060
Window Shade Control
Please Note:
All input devices (low voltage LED switches, IR eye, RF receiver) which connect to the Eye jack must be connected using electrically straight 6-conductor
modular cable (RJ25). This means colors do not cross over: blue leads to blue, green to green, etc. (see diagram below)
COLOR PIN # FUNCT ION
WHITE 1 RQRR CLOCK
BLALL CK 2 COMMON
RED 3 +5VDC
GREEN 4 RQRR DADD TA
YELLOW 5 RP DADD TA
BLUE 6 +12VDC
COLOR PIN # FUNCT ION
RQR CLOCK1WHITE
COMMON2BLAL CK
5VDC3RED
RQR DAD TA4GREEN
RP DAD T A5YELLOW
12VDC6BLUE
Six-Pin Layout
INCORRECT
Tab facing away (down)
WHITE
BLACK
RED
GREEN
YELLOW
BLUE
Tab facing away (down)
WHITE
BLACK
RED
GREEN
YELLOW
BLUE
PIN 6
PIN 1
PIN 6
PIN 1
CORRECT
Tab facing away (down)
WHITE
BLACK
RED
GREEN
YELLOW
BLUE
Tab facing away (down)
BLUE
YELLOW
GREEN
RED
BLACK
WHITE
PIN 6
PIN 1
PIN 6
PIN 1
Page 45 of 124